Slide 1

70V Systems Steve Brooks Atlas Sound Tech Support Manager

Slide 2

InfoComm International Brings You AND Career Development News Network Industry Awareness Market Research Integrated Systems Events Certification

Slide 3

Stay informed! Sign up for Executive Director Randal A. Lemkes Executive Update InfoComm Internationals e-Newsletters: http://subscribe.infocomm.org

Slide 4

What Are We Going To Cover In This Session? A Few Terms Used In This Industry. How 70V Systems Work, With a Brief Comparison Of Consumer Versus Commercial 70V Audio Systems. What Are The Major Components In A 70V Audio System? What Steps Does One Take In Designing A 70V Audio System? A Brief Discussion On Loudness, With Some Examples. The Impedance Bridge, Why You Need One.

Slide 5

Lets Review Some Of The Terminology Constant Voltage - A Name Given To A General Practice Begun In The Late 1920 And Early 1930s Governing the Interface Between Amplifiers And Loudspeakers Used For Public Address Systems. Early Sound System Engineers (Geeks Today!) Looked At this Countrys Electrical Power Distribution System And Used Their Practice Of Distributing Power, Not Voltage.

Slide 6

Constant Voltage The Key Here Is That Power = Voltage x Current. Example - I Want 100W Delivered to My House. Here Are Two Ways To Do This. 10V x 10A = 100W (Low Voltage x High Current) Large Cable Needed Here To Carry The High Current!

Slide 7

Constant Voltage Or, I Could Achieve The Same Result By 100V x 1A = 100W (High Voltage x Low Current) I Can Reduce The Wire Diameter And Still Get 100W To My House!

Slide 8

More Terminology.. Commercial Audio System - An audio system used in commercial spaces, typically used for paging, signaling, Voice Evac and background music. Distributed Audio System - See Commercial Audio System. BGM - Background Music. Music that is played in an office or store at a low level, designed to enhance worker productivity or the shopping experience.

Slide 9

Terminology.. 25/70/100V Audio Systems- Refers To The Maximum Output Voltage Of The Amplifier In The System. - 25V Systems Are Typically Found In Schools And Prisons. Considered Low Voltage, Conduit Typically Not Required. - 70V Is The Most Common, May Or May Not Require Conduit For The Speaker Lines. - 100V Is Used Where Very Long Speaker Runs Are Necessary, The Higher Voltage Results In Lower Current In The Speaker Line, Resulting In Smaller Gauge Wire Needed.

Slide 10

Where Did 70 Volts Come From? Sometime In The Late 1940s, UL Stated That All Voltages Above 100V Peak Will Be Installed In Conduit. To Get Around This And Reduce Install Costs, We Look At the RMS Or Average Of 100V. Vrms =.707 X Vpeak .707 x 100 = 70.7V!- No Conduit!

Slide 11

Terminology.. Transformer Taps- Refers To The Amount Of Power To Be Delivered To A Commercial Loudspeaker, i.e.: 1W, 2W, 5W. The Higher The Number, The Louder The Speaker Will Be. Auto Former - A Specific Type Of Transformer, Used On Attenuators (Volume Controls) In A Commercial Audio System. Also Available As A Stand Alone Product, Used For Stepping Up/Down Voltage And Impedance.

Slide 12

Consumer Versus Commercial A Typical Consumer Home System CD Player Integrated receiver 8 Ohm loudspeakers Assuming This Is A 100W Receiver And It Is Delivering Maximum Power, We Would See About 28VAC At The Speaker Terminals. Remember This Number. This System Has 2 Speakers Connected, Usually Up To 4 Maximum

Slide 13

Consumer Versus Commercial A Typical Commercial BGM and Paging System Paging Microphone CD Player-BGM Source Commercial Grade 70V Mixer Amplifier This Amplifier Is Rated At 120W. At Maximum Power, We See 70VAC At The Speaker Terminals. Commercial grade 70V ceiling speakers

Slide 14

Whats The difference? The Home System Can Only Have A Few Speakers Connected. The Home System Cant Work With Long Speaker Wire Runs Without Using Very Large Diameter Cable, Due To Voltage Drops In The Cable. The Commercial System Can Have Lots Of Speakers Attached To The Amplifier. The Commercial System Can Use Smaller Speaker Wire.

Slide 15

So, How Do We Accomplish This? By The Use Of Step Up And Step Down Transformers We Step Up The Voltage/Impedance (Audio Signal) Which Lowers The Current Coming Out Of The Amplifier, And Step Down The Voltage/Impedance (And Raise The Current Back Up) To The Loudspeakers! Power Companies Do This Everyday, They Step Up The Voltage On The Power Lines For Distribution, Then Step It Back Down At Your Home! Lets Take A Closer Look At Transformers!

Slide 16

Loudspeaker Transformers Typical 8W 70V step down transformer, usually mounted on the loudspeaker High Voltage, Low Current From 70V Amplifier Taps Set The Amount Of Power The Speaker Will Draw From The Amp Low Voltage, High Current To Speaker Primary Secondary

Slide 17

70V Amplifier With Internal Transformer Shown Internal 25/70/100V Transformer To 70V Loudspeakers

Slide 18

One Final Word About Transformers Besides Stepping Up/Down The Voltage, They Also Step Up/Down The Impedance Of The Amplifiers Output And Speakers. By Raising The Impedance, We Can Now Attach Lots Of Speakers In Parallel, Without Causing The Amplifier To See Too Low Of A Load At The Speaker Terminals.

Slide 19

Next Up Now Lets Take A Look At The Major Components In A 70V System.

Slide 20

Amplifiers/Mixer Amplifiers 70V Power Amps Small Mixer Amps Large Mixer Amps Power Amps And Mixer Amps?? Whats The Difference?

Slide 21

Here Is The Difference.. Power Amplifiers Typically Dont Have A Microphone Preamp And Accept Line level Signals Only. Usually Have Multiple Channels. Usually Have A Separate Mixer Connected To The Inputs. ----------------------------------------------------------------------------------- Mixer Amps Have A Preamp and A Power Amp Section And Typically Accept Multiple Line Level And Microphone Level Signals. Mixer Amps Usually Have Tone Controls (Bass/Treble) Included.

Slide 22

Loudspeakers 4 Ceiling Speaker 4 Ceiling Speaker With Tweeter High Power Ceiling Speaker Pendant Type Speaker Surface Mount Speaker Paging Horn High Power Stadium Horn

Slide 23

Slide 24

Attenuators Since We May Need A Way To Control The Loudness Of the Speakers, We Install Attenuators. 70V Attenuators Are Wired Into The Speaker Line, And Are Rated On How Much Power (Speaker Qty. x Tap Setting) They Can Deliver To The Speakers Connected!

Slide 25

While We Are On The Subject How Do We Wire Attenuators To Control The Volume Of Just One Speaker On A 70V Line?

Slide 26

Wiring A 70V Attenuator One Loudspeaker

Slide 27

Wiring A 70V Attenuator Two Volume Controls

Slide 28

Questions?

Slide 29

Designing An Audio System Some Things To Consider.. SPL - How Loud Does It Really Need To Be To Overcome The Ambient Noise Levels? Coverage - Where Does The Page Need To Be Heard? Frequency Response - Paging or BGM or Both? Background Music or Foreground Music? Power - How Large Will Our Amplifier Need To be? Important! What Does The Customer Want Or Expect?

Slide 30

Selecting A Loudspeaker Will They Be Installed Inside or Outside? Will They Be Installed Flush or Surface Mounted? What Is The Ambient Noise Level The Speaker Must Overcome? How Far Will The Speaker Be From The Listener? What Type Of Sound Quality Is The Customer Expecting?

Slide 31

Choosing A Loudspeaker Paging Horns - Used Indoors And Out, Very Efficient, Voice Only Surface Mount - Used Indoors, Voice & Music Ceiling Mount - Used Indoors, Voice & Music

Slide 32

Choosing A Loudspeaker Coaxial Indoor/Outdoor Speaker - Voice & Music

Slide 33

How Many Loudspeakers Do I Need? We Have Chosen The Amplifier And The Loudspeaker, Now, How Many Will I Need? Always Measure The Dimensions Of The Spaces Needing Audio. - Room Length? - Room Width? - Room Height To Ceiling? - Will Occupants Be Seated Or Standing?

Slide 34

What Is One Of The Most Important Things To Consider When Designing An Audio System? A. The Customers Ability To Pay For It? B. Can I Get 60 Day Terms From My Vendors? C. Proper Loudspeaker Spacing? D. Does The Customer Get The Keys To The Equipment Rack? Answer. Proper Speaker Spacing!

Slide 35

Loudspeakers - How Many? Here Is The Hard Way To Calculate. 6 Speaker in a 10ft ceiling r = (10-5) tan 110/2 r= 7.14

Slide 36

Dont Have Time To Do The Math? Most Speaker Manufacturers Provide A Ceiling Speaker Calculator On Their Website! Make Use Of It!

Slide 37

We Should Look At Three Accepted Ceiling Speaker Spacing Scenarios Each Type Has Its Own Pros And Cons Lets Start With

Slide 38

Edge To Edge Ceiling Layout Notice The Large Gaps In The Coverage? -6dB Down Point For The Loudspeaker Or The Power 14 On Center

Slide 39

Minimum Overlap Speaker Layout 10 on center See the overlap between adjacent speakers?

Slide 40

Edge To Edge Layout 7 On Center Lots Of Overlap Between Speakers Our customers may not want a system with this much density, nor would they want to pay for it!

Slide 41

A Typical Ceiling Speaker Layout

Slide 42

How Loud Does The System Need To Be? The System Only Needs To Be Loud Enough! Typically, We Shoot For Minimum 6dB Above Ambient Noise Levels, 10dB Is Better. It Is Much Easier To Turn Down The System At The Amplifier Than It Is To Go And Re- Tap All The speakers Up!

Slide 43

Lets talk About Loudness This One Goes To 11!

Slide 44

SPL Design Goals Paging Horns Required Here Typical 8 Ceiling Speakers Here, Tapped At to1W. Be Careful If SPL Is Above 100dB!

Slide 45

Now Lets Look At Wire

Slide 46

Loudspeaker Wire 70V Speakers Are Always Wired In Parallel, (+) To (+), (-) To (-). Use Stranded Wire, Do Not Use Voice And Data Wire (CAT5). Solid Core Data Wire Is Too Small And Can Be Unreliable When Twisted Typically, 2 Conductor, Stranded Of Sufficient Capacity For Speaker Lines 18 Gauge, 2 Conductor Stranded Is Most Common For Small To Mid Size Systems. Shielded Cable Is Unnecessary!

Slide 47

Calculating The Proper Size Wire If You Are Unsure, Or Have An Install With Many Loudspeakers And Long Speaker Runs Then We Need To Determine The Wire Size For This Job. Its Best To Calculate The Total Speaker Load That The Amplifier Will Be Required To Drive AND The Total Wire Length.

Slide 48

Calculating The Load Impedance The Formula For Calculating The Total Load Impedance Comes From Ohms Law. Zt=E / P Zt Is The Total Impedance You Are Looking For E = 70.7 X 70.7 or 5000 P = The Number Of Speakers X The Tap Setting

Slide 49

Lets Look At An Example Example: A system has 50 speakers, all tapped at 5W each. So, 5 X 50 = 250, this is P in the equation, and we already know E = 5000. So, divide 5000 by 250, and the answer is..20 impedance! Zt = E / P The Total Speaker Load That The Amplifier Sees Is 20.

Slide 50

Now We Factor In The Speaker Wire.. Load Impedance = 20 ohms Speaker run is 200 feet, and wire specified (14 gauge) has a resistance of.0025 ohms per foot. So, multiply.0025 X 200 X 2 = 1 ohm. The 2 in the equation is for the loop length, out and back. Add The 1 Ohm To Our 20 Ohms = 21 Ohms Looking at the wire gauge chart, I see that we will have -.4dB loss, which is acceptable with this wire and speaker load!

Slide 51

Wire Calculator RunZZsource 200ft210.01 AWGSq mmR per footLoop ResistancedB LossStatus 88.360.0006280.2512-0.1Okay 105.260.0009990.3996-0.2Okay 123.310.0015880.6352-0.3Okay 142.080.0025251.0100-0.4Okay 161.310.0040161.6064-0.7 180.8230.0063902.5560 200.5170.0101524.0608-1.6 220.3250.0161426.4568-2.4

Slide 52

Speaker Zones How Many Zones Will There Be? Are The Zones Volume Zones Or Content Zones? Each Content Zone Requires A Separate Amplifier! Each Volume Zone Requires A 70V Attenuator!

Slide 53

Questions????

Slide 54

Selecting The Proper Amplifier What Are The Power Requirements? We K now That Our Total Speaker Load Is 21 (Zt) So How Do We Know How To Choose The Correct Amplifier Size? As A General Rule Add 20% To The Total Load And The Closest Available Amp Size (Always Round Up) 5000 Divided By 21 Ohms = 238W 238W * 20% = 47.6W (+ 238W) = 285W Choose An Amplifier Rated At 300-350W / Channel

Slide 55

The Impedance Bridge What Is It, And Why Is It Often Missing From Most Toolboxes? The Impedance Bridge Is A Meter For Measuring The Impedance Of A 70V Speaker Line. It Measures Impedance At A Specific Frequency Using An AC Signal. Gives A Reading In Ohms Or Watts. VOMs Do Not Do This! The Bridge Cannot Measure Voltage Or Current, And Is Typically Not Used Everyday By Installation People.

Slide 56

The Impedance Bridge If One Calculates The Expected Impedance (Remember Taps X Speaker Count?) And Then Measures The Loudspeaker Line, The Numbers Should Be Close. If There Is A Big Difference, Its Time To Figure Out Why. The Impedance Bridge Connects To The (+) And () Connections Of The Speaker Line. It Measures The Impedance At One Or Several Frequencies, Much Different Than Using A Standard VOM Set For Resistance!

Slide 57

Typical Impedance Sweep Of An 8 Ohm Loudspeaker

Slide 58

Using The Impedance Bridge Lets Go On A Service Call And Do Some Troubleshooting With Our Impedance Bridge. We Have A Paging System That Was Working Well Until Yesterday. The System Has 8 Speakers Tapped At 1W, A 70V Mixer Amp and Paging Is Done With A Desktop Microphone. The Customer Says The Amp Is Running Hot And The paging Is Distorted. We Check Out The Equipment And Wiring In The Rack And Everything Appears OK. Next Step..

Slide 59

Impedance Bridge Continued.. We Calculate The Load 8 Speakers X 1W Tap = 8W, Impedance = 5000/8 = 625 Ohms. We Disconnect The Speaker Line And Connect The Bridge. The Bridge Measures