4 -ip-10g install - presentation v1.0

7/31/2019 4 -IP-10G Install - Presentation v1.0

1/26

Proprietary and Confidential

Installation

FibeAir IP-10 G-Series


2/26


General

2

If installation requires CFG file upload & download and / or SW fileupload & down -

1. Make sure FTP Server is installed on your PC2. FTP is configured (RD/WR permissions)

3. Latest SW version is available (FTP root directory)

FTP installation guide

is available at

Training.Ceragon.Com:

see Modules /

Installation


3/26


Site Requirements

3

IDU must be located indoors

The environment temperature must be between -5 C and +45 C.

Easily accessible, but only by authorized personnel.

Available power source of -48 VDC, and the site must comply with

National Electric Code (NEC) standards.

Available management connection (Ethernet or dial-up). IDU-ODU connection (IF cable): no more than 300m


4/26


Site Requirements

4

Heat Dissipation:

The IP-10 IDU overall heat dissipation is 25W max (~85 BTU/h).The ODU heat dissipation is 100W max.

Antenna Location:

As with any type of construction, a local permit may be required before installingan antenna. It is the owners responsibility to obtain any and all permits.


5/26


IDU Dimensions

5

42.60mm


6/26


Installing standalone IDU in a 19 Rack

6

As shown in the illustration, four screws, supplied with theinstallation kit, are used to secure the IDU to the rack.


7/26Proprietary and Confidential

Installing Nodal Enclosures in a 19 Rack

7




8

Before you install theenclosures

Plan carefully the requiredspace within the rack !

Should you need to install 3enclosures prepare at least10Us (6Us for enclosures + 2Us freespace for maneuvering above and below

shelves)

Start the installation processfrom bottom to top, e.g. Mainenclosure should be installedfirst at the bottom of your rackspace

Main Enclosure




9

Step #1:Install the IP-10 Main enclosurein the 19 inch rack using 4screws.




10


Step #2:

Slide down the 2nd extensionenclosure. Male connectorshould plug in smoothly into theMain enclosure.




11


Step #2:

Slide down the 2nd extensionenclosure. Male connectorshould plug in smoothly into theMain enclosure.

Step #3:

Slide down the 2nd extensionenclosure. Male connectorshould be plugged in smoothlyinto the Main enclosure.




12

Step #4:Secure the 2nd extension intothe Main enclosure. Use thebuilt-in screw.

Mount the 2nd extension into the

rack using the 4 screws


13/26



13

Step #4:Secure the 2nd extensioninto the Main enclosure.Use the built-in screw.

Mount the 2nd extension

into the rack using the 4screws

Step #5:Add the 3rd extensionwhen needed


14/26


Preparing the IDU for a Shelf installation

14

Remove the two 19" brackets mounted on the IP-10 IDU by unscrewing the 3

screws at each side.


15/26


Installing the IDU in a Shelf

15

Slide the IP-10 IDU into the enclosure and tighten it using 2 screws. Repeat

this step in accordance with the configuration.

IDU insertion & extractionshould NOT be under power


16/26


Installing a Blank Panel IDU in a Shelf

16

Slide the IP-10 blank panel into the enclosure, and tighten it using 2 screws.


17/26


Installing a T-Card into an IDU

17

Remove the IP-10 T-Card blank panel from the IDU, by releasing the 2 side

screws.


18/26


Installing a T-Card into an IDU

18

Insert the IP-10 T-Card panel and tighten it using the 2 side screws.


19/26


Grounding the IDU

19

Single Point Stud

Grounding Wire


20/26


Grounding the IDU

20

The IDU is suitable for installation in a Common Bonding Network (CBN).

Only copper wire should be used.

The wire must be at least 14 AWG.

Connector and connection surfaces must be plated. Bare conductors must be

coated with antioxidant before crimp connections are made to the screws.

FibeAir provides a ground for each IDU, via a one-hole mounted lug onto asingle-point stud.

The stud must be installed using a UL-listed ring tongue terminal, and two star

washers for anti-rotation.


21/26


Power General Requirements

21

1. A readily accessible Listed branch circuit over-current protective device,rated 15 A, must be incorporated in the building wiring.

2. This equipment is designed to permit connection between the earthedconductor of the DC supply circuit and the earthing conductor at theequipment.

3. The equipment shall be connected to a properly grounded supply system

4. The DC supply system is to be local, i.e. within the same premises as theequipment

5. A disconnect device is not allowed in the grounded circuit between the DCsupply source and the frame/grounded circuit connection.


22/26


Power Requirements

22

When selecting a power source, the following must be considered:

DC power can be from -40.5 VDC to -60 VDC.

Recommended: Availability of a UPS (Uninterrupted Power Source),

battery backup, and emergency power generator.

Whether or not the power source provides constant power (i.e., power issecured on weekends or is shut off frequently and consistently).

The power supply must have grounding points on the AC and DC sides.

The user power supply GND must be connected to the positive pole in the IDU

power supply.

Any other connection may cause damage to the system!


23/26


Power Requirements

23

Important

Make sure to use a circuit breaker to protect the circuit from damage byshort or overload.


24/26


Installing the IDU-ODU IF cable

24

Route the IF Coax Cable from the IDU to the ODU/RFU and terminate it

with N-type male connectors.

Note: Make sure you fasten the cable along the ladder!

Make sure that the inner pin of the connector does not exceed theedge of the connector.

The cable should have a maximum attenuation of 30 dB at 350 MHz.


25/26


Logging in, assigning IP address

CLI access groups:

Viewer read-onlyaccess

Operator read-writeaccess but cannot add/remove other users

Admin read-writeaccess including add/remove other users

Tech read-writeaccess including add/remove other users as

well as access to a bridge-specific CLI shell

Currently only Admin is defined

Other groups or users can be created via CLI only


26/26

P i t d C fid ti l

Thank You !

4 -ip-10g install - presentation v1.0

Documents