265 (002391- ) na parts manuald2z4qs2e3spnc1.cloudfront.net/...sn...parts_manual.pdf · operation,...

POWER SWEEPER Operation, Maintenance, and Parts Manual Including High Dump Model, First Serial Number 2391

t E W WANT SPECMIZED 0 MAINTENANCE SYSTEMS SWEEPERS. SCRUBBERS. SCARIFIERS. FLOOR COATINGS

Find ... Go To..

CEwra~v 265 POWER SWEEPER

This manual is furnished with each new TENNANT" Model 265. The machine operators wlil easily learn how to operate the machine and understand its mechanical lunctions by following the directions and absorbing the information in the Operation section.

This machine will give excellent service and sweeping results. and save maintenance expenses. However, as with all specially engrneered mechanical equipment, best results are obta~ned at minimum costs if:

The machine is operated w~th reasonable care and r The machine is maintained regularly - per the maintenance instructions provided.

Components used in this machine have been carefuily seiected lor performance and safety. Use only Tennant Company supplied or equivalent parts.

Parts and supplies may be ordered by phone or mail from any Tennant Company parts and service center, distributor. or from any of the Tennant Company subsidiaries.

The telephone, telex, mailing addresses, and locations are listed on the last page of the manual.

MANUAL NO. MM114 Published: 1-84

Tndcrut Rg~mnl (D: l r r r a Besim. Dmri. Eaqlr~l. F n r r . Cerluq, lbh. Sara, SnkmilmL U n ~ k d Sbltt Ltg<lb.l. 6 m W . Czmll. JWI. Me1.1. S*ML 4 T E l W l l l CUMPAHI. Uirn!wolir. Lmwlab. USA '1984. Tennant Company. Printed in U.S.A~

Find ... Go To..

STANDARD

POWER SWEEPER

CONTENTS Fig. 1 - Main Frame & Related Parts Fig. 2 - Seot 8, Instrument Panel Fig. 3 - Engine & Related Parts Fig. 4 - Ai r Cleaner & Related Parts Fig. 5 - Cooling System Fig. 6 - Exhaust System Fig. 7 - Gasoline Tank Fig. 8 - Gasoline Carburetor, Fuel Pump, Governor Fig. 9 - Filter System Fig. 10 - Vacuum Fan Assembly Fig. 11 - Rear Wheel Assembly Fig. 12 - Rear Drive Motor & Related Parts Fig. 13 - Main Brush Lift Gnlrols Fig. 14 - k i n Brush Drive 8 Related Pam Fig. 15 - Side B ~ s h Support & Drive Fig. 16 - Front Wheel & Brake Assembly Fig. 17 - Handbmke & F o o t Brake Sfiem Fig. 18 - Steering & Related Pam Complete Hydmutic System with Vickers Pump Fig. 19 - Drive Mofor & Related Parts Fig, 20 - Side Brush, Main Brush & Vacuum Fan Fig. 21 - Hydmulic Cylinder, Valve & Filter Group Fig. 22 - tlydmulic Tank & Related Ports Fig. 23 - Hydmulic Pump & Related Parts Fig. 24 - Pump Control Linkages Fig. 25 - Electrical System

List of Decals

This section includes parts for a Standard Model 265 equipped with a gasoline engine. For scrubber attachrnenfs or other accessories, see "Accessories Parts List". For Hi-Dump machines, see "Hi-Dump Parts List". For LPG fuel machine, see "LPG Po+ List". Breakdown parts l is ts for hydmulic components are shown On "Hydmulic Components Section".

Find ... Go To..

Find ... Go To..

ORDERING REPAIR PARTS

To avoid errors or delays in filling parts orders, please BOLT AND CAP SCREW STRENGTH furnish all of the following information. IDENTIFICATION

1. Always specihl the machine model number and Bolts and cap screws required to have high-strength the machine serial number shown on themachine qualities to 8AE G~~~~ 8 are identified data plate. throughout this catalog by the description GR 8. Unless

identified by this desc;ipion, ail standard bolts and screws are SAE Grade 5.

2. Give the part number, description, and the quantity needed of each item on the order. Do not order by reference number or the figure number of the illustrated parts.

3. Indented items indicate parts of assemblies. Standard hardware is furnished only when part of a purchased assembly. Please order hardware from a local hardware supplier.

4. If the old part cannot be identified, send it to us with the quantiiy needed specified on the order.

5. State definite shipping instructions to include the shipping address andlor the billing address if there is a difference. Any claim for loss or damage to a shipment in transit should be filed promptly against the transportation company making the delivery. Shipments will be complete unless the packing list or order acknowledgement indicate items back ordered.

If parts received are suspected to be incorrect or defective, please write, wire, or phone the Tennant Company representative from whom you ordered the part. They will give authorization for return and/or handle replacement shipments when required.

S1 (INTERNAtlONALSYSTEMl UNITS OFMEASURE

Metric equivalents have been included, where applicable. throughout this parts catalog.

I cap

Find ... Go To..

Find ... Go To..

Fig. 1 - FRAME AND RELATED PARTS

Ref. TENNANT No. Port No. Description Qtv.

1 "33762 DOOR, Brush, R.H. 1 2 23752-2 SHIM (if needed for weld-hinged door) 1 3 45857 RETAINER, Skirt 2 4 23275 SKIRT, Side 2 5 07259 FITTING, Grease I 5A 08407 FITTING, Grease 1

6 231 38 SHIM, Liftarm 1 7 23454-2 BEARING, Torque tube, right 1 8 56855 STOP, Sofety arm, rubber I 9 53003 ARM, Hopper, safety stop I 10 461 37 SLEEVE 2 I? 461 32 HOOK 2 12 461 47 WASHER, Neoprene 2 13 2 1 097 HOOK 1 14 23452-2 CAM, Hopper, adjusting 2 15 23384-2 RETAINER, Side seal 2 16 23382 SEAL, Hopper Side 2 17 53143 RETAINER, Top seal 1 18 23386 SEAL, Hopper top 1 19 23583-2 A STUD 1 20 53056 ARM, Lift 1 2 1 23580-2 BEARING, Toque tube, center 1 22 23455-2 BEARING, Torque tube, left 1 23 53298 SKIRT, Rear, (Brush Contuct) 1 24 53219 ANGLE, Skirt m w n t 1 25 531 37 SKIRT, Rear, (Floor Confact) I 26 23268-1 RETAINER, Rear skirt 1 27 09 342 CHAIN, Dmg(static xrfety) 1 28 **33760 DOOR, Access, L.H. 1 29 53974 SEAL, Access door 2 30 33504 FRAME, Moin 1 31 53052 SEAL, Access door 2 32 1 1 893 EYE BOLT 1 33 43250 TIP, Rubber 1 34 46307 CHAIN, Bumper hold-up 1 35 24528 ANGLE, Tie 2 36 53637 BUMPER 1 37 46567 HOSE, Chain cover 1 38 32885 HINGE, Brush door, R.H. 1 39 32886 HINGE, Brush door, L.H. 1

47954 SLEEVE, Drag chain 1 40 4621 3 PLUGNUTTO N I A1 10632-1 5 GROMMET 1

*To repface R.H. Brush door with welded on hinge, order 5K251.5; to replace door with bolted on hinge used on machines up to serial number 8543, order SK2726.

**To replace L.H. Brush door with welded on hinge, order SK2514; to replace door with belted on hi 1 o r 6K2724.

Find ... Go To..

7/83 4 /

Find ... Go To..

Fig. 2 - SEAT, INSTRUMENT PANEL & RELATED PARTS

Ref. No.

TENNANT Part No.

53871 53844 53729A 531 28 53465-2 50824 54371 -1 5351 3 54936 50808 5472 1

SEAT MOUNT, Seat SUPPORT, Seat PLATE, Cover COVER, Battery BRACKET, Seat support PANEL, Access PANEL, Instrument COVER, Engine panel DOOR, Instrument panel BOX, Instrument PANEL ASSEMBLY AkM, Hinge ARM, Hinge HINGE, Engine cover HINGE, Side door DOOR, Side COVER, Engine PANEL, Corner GRILL COVER, Top rear BUMPER SLEEVE, Instrument box mounting BRACE BRACKET TREAD, Floor STRAP, Rubber SPACER, Wood PLUGBUTTON, 0.50" PLUGBUTTON, 0.39" PLUGBUTTON, 2.1" PLUGBUTTON, 1.3" PLUGBUTTON, 0.88" PLUGBUTTON, 1.4" GROMMET GROMMET SEAL, Seat support

Qtv,

Find ... Go To..

Find ... Go To..

FIG. 3 - ENGINE AND RELATED PARTS 01899

Ref. TENN4NT No. -- Part No. ---2 Dercri tian - Qt y .

DAMPER, Engine MOUNT, Engine, left hand SPACER, Alternator ALTERNATOR ASSEMBLY (includes

ALTERNATCX REGULATOR, Voltoae

following)

- FAN, ~ l fe rna to r

STRIP, Alternator SHEAVE, Alternator BRACKET, Alternator mounting

**ENGINE, basic, Gasoline SCREW, Hex cap, 8mm PULLEY, Water pump STRAP, Coil COIL, Ignition PULLEY, Crankshaft V-BELT, Alternator-water pump V-BELT, Fan, radiator RESISTOR, Ignition coil MOUNT, Engine, right hand BRACKET, Motormount NUT, Hex, 5mm

*STARTER, Engine *RING, Starter locatins *PIN, Dowel COUPCI NG, Chain (Engine side) BRACKET, Motor & valve mount HOUSING, Flywheel BUSH I N G KEY COUPLING, Chain, half (pump side) sp!ine C W I N. Cou~l ina

8 " PLATE, ' Pump drive adaptor CABLE, Grounding SAP, O i l filler & breather

* DIPSTICK, O i l level *TUBE, Dipstick *ELEMENT, Engine o i l filter

SHlM (16-GA thick) SHlM (0.19" thick). WIRE, Coil high tension WASHER, Engine mount

+ 3RAI N COCK

Basic engine 32837 replaces engine 54912-1 on machines with S/N 7514 and above. To replace previous engine 54912-1, order SK2493.

Basic engine does not include alternator, voltage regulator, V-belts, fan, carburetor, pulleys, coil, resistor, etc.

These parts are included i n basic engine 32837 7

Find ... Go To..

Home

n A - rl F A N F R A N D RFI ATFn P A R T S

Find ... Go To..

Fig. 4 - AIR CLEANER AND RELATED PARTS

Ref. TENNANT No. Part No. Description Q t y .

1 26509 NUT, Wing, 0.25" - 20 1 2 41 178 WASHER , Steel 1 3 23791 8 COVER, Air cleaner 1 4 46591 NUT, Wing , 0.25" - 20 1 5 24924 WASHER, Nylon 1 6 5408 1 COVER 1 7 2731 3 ELEMENT, A i r filter, inner 1 8 23792 ELEMENT, A i r filter, outer 1 9 54082 STUD 1 10 54080 FUNGE, A i r cleaner 1 1 1 23731 WASHER, Neoprene 1 12 23727A-2 BASE, Air cleaner 1 13 47388 ELBOW 1 14 54148 HOSE, Breather 1 15 54333 * CLAMP 2 16 51706 * SLEEVE 1 17 4681 8 CLAMP, Wire 1 18 54155 * ELBOW, Rubber 1 19 3351 8 WASHER, Rubber 1 20 24669 DECAL, Fmm aircleaner 1 * Note: These parts are used on "old style" a i r cleaner only.

Find ... Go To..

10

Find ... Go To..

Fig. 5 - C O O L I N G SYSTEM 01900

Ref. TENNANT No. Part No. Description G ? k

1 51 321 -3 CAP, Radiator 1 2 11531 CLAMP, Wormdrive 6 3 '19593 RADIATOR 1 4 51322 DAMPER, Radiator, v ibmtion 4 5 54874 TUBE, Uadiator I 6 54884 HOSE, Radiator, (To engine) 1 7 48648 FAN (4-blade) 1 8 53867 PULLEY, Fan 1 9 23217 RING, Retaining 2 10 28868 BEARING & SHAFT, Fan 1 1 1 50837 ARM, Fan, mounting 1 12 32836 BRACKET, Fan, arm mounting 1 13 50864 SPRl NG 1 14 11398 PIN, Roll 1 15 54387 SHROUD, Fan (no longer used) 1 16 51 305 ' DRAIN, Radiator angle 1 17 26897 COUPLING 1 18 26385 NIPPLE 1 19 * *50956 HOSE, Radiator, Upper 1 20 42331-1 BOLT, Eye 1 21 50476 HOSE, Radiator (Bottom) 1 22 50825 BRACKET, Support 1 23 50824 BRACKET, Spr i ng 1 24 54795 +BRACKET, Twnbuckl e 1 25 25494 -t- TURNBUCKLE, Bel t tens i oni ng 1 26 14896-1 SHIM, 0.05" (1 -0 mm) 1 27 14896-3 SHIM, 0.01" (0.5 rnm) 1 *To replace radiator on machines wi th serial number up to and including 7587, order SK2487. Machines with serial number from 7588 to 8157 use SK2676.

**Machines with serial number up to and including 7587 used base 10323-6. To replace 10323-6, order SK2544.

+Note: Machines with serial number up to and including 8132 used the o ld style turnbuckle tensioning. To replace with the new spring tensioning, order SK2564.

7/83 11

Find ... Go To..

Y

Find ... Go To..

Fig. 6 - EXHAUST SYSTEM 01 896

Ref. TENNANT No. Part No. Description Qty.

1 50962 PAD, Rubber 2 2 54274 l SOLAT OR 1 3 47989 *BRACKET, Muffler support 1 4 47990 *SUPPORT, Muffler 1 5 09832 SPACER 2 6 53884 PIPE, Tail 1 7 23693 CLAMP, Muffler 1 8 50830 SHIELD. Muffler, heat 1

10 53820 MUFFLER 1 1 1 2401 2 CLAMP, Muffler 1 12 50966 ** PIPE, Exhaust 1 13 2401 2- 1 CLAMP, Muffler 1 14 50957 ** BRACKET, Exhaust tube 1 15 48630 BRACKET, Exhausf. tube 1 16 5491 1-21 GASKET, Exhaust manifold, end 2 17 5491 1 -2Co CASKET, Exhaust manifold, center 1 18 32838 MANIFOLD, Engine exhaust 1 19 32840 GASKET 1 20 32841 STUD 2 2 1 32842 NUT 2 22 50958 ** PIPE, Exhaust T 23 5K2068 HANGER KIT, Muffler, includes items: 1

2, 3, 4, and 5 24 SK2131 *MANIFOLD KIT, Replacement, includes items: 1

12 through 22 25 48631 'BRACKET, Exhoat pipe 1 26 48630 "BRACKET, Exhaust pipe 1 27 54926 "PIPE, Exhaust 1

* Applicable to machines with serial number up to 7032

** To replace these parts on machines with serial numbers up to and including 8132, order SK2565

13

Find ... Go To..

Fig. 7 GASOLINE TANK & RELATED PARTS

. . 7/83

-, Find ... Go To..

FIG. 7 - GASOLINE TANK & RELATED PARTS 01897

Ref. TENNANT No. Part No. Description Qty .

1 23390 TANK, Gas 1 2 23254 STRAP, Gas tank 2 3 43844 CLAMP, Hose, worm dirve 2 4 54845 HOSE, Rubber 1 5 46236 CLAMP, Hose 3 6 53390-1 GAS LINE ASSEMBLY 1 7 22383 NIPPLE 1 8 04601 STRAINER B SEDIMENT BOWL, Fuel 1 9 17413 Nl PPLE 1 10 - 48267 CAP, Gas (included in item 1 12 53011! SHIELD, Gasoiine 1 13 23826 SEAL 1

7/8 3

Find ... Go To..

-- Old S t y k

Fig. 8 Gasoline Carburetor, Fuel Pump, Govern~r and Related Parts

Find ... Go To..

Fig. 8 - GASOLINE CARBURETOR, FUEL PUMP, GOVERNOR 8 RELATED PARTS


CLAMP 2 LEVER, Throttle 1 HOSE, Air intake (new one-piece molded type) 1 AIR-HORN, Carburetor 1 GASKET, Carburetor to oir horn 1

*CARBURETOR, Gasoline (Repair k i t i s 38501) 1 ELBOW, Fuel inlet 1 CLAMP, Wormdrive 2 HOSE, Gasoline , 0 .31m x 16" (7.9 x 406 mm) 1 GASKET, Carburetor 3 PLATE, Carburetor spacer 1 HOSE, Rubber, governor to distributor 1

0.16" x 12" (4 x 305 mm) furnished with engine CONNECTOR 1 GOVERNOR, Speed 1 STUDS, 1 . 3 1 " ~ 1 8 x 3.38" ( 3 2 x 18x 86 mm) 2 PUMP, Fuel (Gasoline only) 1 SPRING, Throttle return 1 BALLJOI NT 1 CABLE ASSEMBLY, Choke 1 ROD, Throttle 1 BALLJOI NT 1 PIVOT, Arm 1 CLAMP, Stop, throttle control 1 SCREW, 0.25" x 20 x 1.75" 1 ELBOW, Barbed 1 HOSE 1 SLEEVE. Stud 2

* To replace "Old-style" Carburetor, order SK2588.

** Ford Port Number

-1- Previous air intake hose (g50331) hod spring (f50349) located inside. To replace this hose with new molded hose, order SK1844.

., -- . .

Find ... Go To..

Fig. 9 FILTER SYSTEM

Fig. 9 - FILTER SYSTEM

Ref. No.

6 7 8 9 10 11 12 13 14 15 16 17 18 19

21 22

(not shown) 23 24 25 26 27 28 29 30 31

TENNANT Part No. Description

COVER, F i l t e r box SEPARATORS BAG, Filter RACK, Bag BAR SHAKER MOTOR ASSEMBLY

STRAP, Shaker motor BAR, Rubber WEIGHT, Eccentric MOTOR, Shaker (sealed, not repairable) SUPPORT STRIP, Rod clamp

ROD, Clamp, lower SEAL, Extrusion BOX, Filter STRAINRELIEF DEFLECTOR, Dirt, left hond PLATE LIP BACKING DEFLECTOR, Dirt, right hond SUPPORT. Pan, right hand SUPPORT, Pan, left hand CATCH SPACER CATCH, Spring DOOR, Hopper SEAL, Set SPRING HINGE PIVOT FIRE DOOR FUSIBLE LINK PLUGBUTTON, 0.41 " (10.4 mm) PLUGBUTTON. 0.56" (14.2 mm) FASTENER CLAMP, Cable

Find ... Go To..

Fig.10 - VACUUM FAN


CLIP, Vacuum hovsing MANIFOLD, Intake SEAL, 0.31" x 30.50'' (7.9 x 777 mm) IMPELLER HOUSING, Impeller ISOLATOR, Vibration PLATE, Motor mounting MOTOR, Vacuum fan (inclvdes hardware)

SEAL KIT SLEEVE ADAPTER, Hose BRACKET, Hose adapter CLAMP, Wormdrive HOSE MUFFLER ASSEMBLY, Fan 1

MUFFLER, f a n 1 SEAL, Foam rvbber, 3.3" (84 mm) 2 SEAL, Foam rvbber, 6.6" (168 mm) 2 I NSUiATl ON, Muffler, top 2 I NSULATI ON. Muffler. side 2 .

19 T5951 WASHER, Flot, 0:38" 1

"Note: Before serial number n O l , vacuum f a n motor was 53923. To replace 53923, order SK2560. Seal k i t For both motors i s SK2561.

- 4

Find ... Go To..

Fig. 11 - REAR WHEEL ASSEMBLY

Ref. TENNANT No. Part No. Desc.ription Qty . 1

47550 WHEEL ASSEMBLY 53818

1

2 RIM ASSEMBLY

47525 TIRE 1 pr.

3 1

53819-1 TUBE, Inner 4 1

53819-2 5

FLAP, Tire-tube 24339 1

NUT, Wheel 5

Find ... Go To..

Fig. 12 - REAR DRIVE MOTOR & RELATED PARTS


1 53528 BAR, Support, drive casting 1 2 53525A SUPPORT, Drive casting 1 3 49225 BEARING CONE 8 CUP ASSEMBLY (includes 2 bearings 1 4 14242 NUT and 2 cones) 1 5 24984 PIN, Support 1 6 53893 HUB 8 STUD ASSEMBLY 1

24338 STUD 5 7 53032 MOT OR, flydiaulic (Ross) 1

SKI 140A SEAL KIT 1 8 53481 DRIVE LINK 1 9 47719 WASHER 1 10 39305 SCREW 4

Find ... Go To..

r1l

Line

r1l

Line

r1l

Text Box

1

r1l

Text Box

1

r1l

Line

r1l

Text Box

2

Fig. 13 - BRUSH LIFT CONTROLS

Ref. TENNANT _No. Part No. Description Qty .

1 261 56 KNOB 1 2 23304 HANDLE 1 3 23306-1 CLIP 1 4 14174 SPRING 1 5 23307-1 LEVER, Lift handle 1 6 24339 NUT, 0.50" - 20 1 7 5 1452 KNOB I 8 53876 ARM, Lift 1 9 51 391 PIN, Swivel 1 10 53906 SEAL, Rubber 1 1 1 53182 ROD, Lift 7 12 GI37156 NUT, Wing 1

Find ... Go To..

Fig. 14 - MAIN BRUSH DRIVE & RELATED PARTS


53187 ARM B PLUG ASSEMBLY, Brush, right hand 1 1 53168 ARM, Brush, right hand 1 2 51984 PLUG ASSEMBLY, Brush idler 1 3 24899 BEARING, Ball 1 4 51 046 RING, Retaining 1 5 51 564 WASHER 1 6 53985 PLUG, Threaded 1 7 53169 ARM, Brush, left hand 1 8 20050 PIN, Roll, 0.31" x 1.88" (7.9 x 47.8 mrn) 3 9 51 036 PLUG, Drive 1 10 * 35973 FLANGE 4 11 * 23624 BEAR1 NG 2 12 35677 ROD, Lift 1 13 * 50521 BRACKET 2 14 53906 SEAL, Rubber 2 15 35674 SHAFT, Counter 1 16. 531 38 HUB ASSEMBLY, Brush 1 Note: To replace previous flange, bearing, and bmcket, order SK2361.

7/82

Find ... Go To..

Fig. 15 - SIDE BRUSH SUPPORT 6 DRIVE

9/79 26

Find ... Go To..

Fig.15- SIDE BRUSH SUPPORT AND DRIVE

Ref. TENNANT No. Part No. Description Qtv.

1 26 156 KNOB, Li f t lever 1 2 23304 LEVER, Brush l i f t 1 3 23293 NUT, Adjusting (for top 23294) 1 4 23306-1 CLI P, Lift arm 1 5 23307-1 ARM, Lift 1 6 14174 SPRING 1 7 23294 CABLE, Lift, side brush 1 8 23503A YOKE, Lift, side brush 1 9 22 143 SPACER (for 23503A) 1 10 23536 PIN, Pivot 1 11 46347 LUG,Side brush 1 12 24207 BRACKET, Angle adjusting 1 13 43228 BRACKET, Motor mwnting 1 14 4750 1 ADAPTOR, Brush 1 15 46034 BUMPER, Side brush I 16 46033 SUPPORT, Bumper 1 17 48062-1 ARM, Side brush support 1 18 23191 PIN, Clevis, 0.38" x 3" (9.7 x 76 mm) 1

Find ... Go To..

Fig. 16 - FRONT WHEEL & BRAKE ASSEMBLY

Ref. TENNANT Na . Part No. Description Qtv.

FRONT WHEEL ASSEMBLY DISC , Wheel TIRE, Zero pressure, front HUB, Front wheel RING, Retaining BEARING

WASHER, Wheel retaining FRONT AXLE ASSEMBLY

SHOE, Brake (2 per wheel) SPACER, Heel pin PIN, Heel AXLE & BUSHING ASSEMBLY

BUSHING ARM, Brake CAM, Brake SPRING PIN, Roll

SPACER

Find ... Go To..

Fig. 17 - HANDBRAKE 8 FOOT BRAKE ASSEMBLY

Ref. TEN NANT No . Port No. Description Qty.

1 3691 3 HAND BRAKE ASSEMBLY 1 03560 SPRING 1 1 0677 PIN, Roll I 24245 SUPPORT 1 24246-1 LEVER 1 35671 ROD 1 24258 WASHER 2

2 18141 PIN, Roll 1 3 23529A STRAP 1 4 071 42 PAD, Pedal 1 5 14605 PIN, Clevis, 0.25" x 0.75" ( 6 . 4 ~ 19 mm) 1 6 23483-2 ROD, Adjustment 2 7 35676 SHAFT, Brake 1 8 28296 PIN, Clevis, 0.25" x 0.50" (6.4 x 12.7 mm) 1 9 03091 SPRING 1 10 23280-2 HANGER, Broke shaft 2 11 23758-1 SHIM, Hanger (for 23280-2) As req. 12 14595-1 CLEVIS, Adjustable 2 For breakdown of tire, wheel and brake see " Front Wheel and Brake" page.

11/81 29

Find ... Go To..

Find ... Go To..

Fig. 18 - STEERING 8 RELATED PARTS


1 4701 0 BUTTON, Horn 1 2 4701 1 BRUSH UNIT, Horn 1 3 47008 WHEEL, Steering 1

47007 * COLUMN & GEAR ASSEMBLY 1 4 1 14496 NUT, Steering wheel (0.5" - 20 jom nut) 1 5 264832 SPRING 1 6 5695951 BEARING 8 CABLE ASSEMBLY 1 7 264831 SEAT, Spring 1 8 5695956 COLUMN 1 9 103868 or 444746 PLUG, Filler 1 10 5692532 HOUSING 1 11 7802482 ADJUSTER, Lash 1 12 781 2838 SECTOR AND SHAFT ASSEMBLY 1 13 266316 BUSHING, Sector shaft 1 14 566734 GASKET 1 15 7801626 SEAL 1 16 5666683 CUP, Upper worm bearing 1 17 5666693 BEARING, Upper ball 1 18 5695954 WORMSHAFT 1 19 5666886 NUT, Ball 1 20 5666693 BEARING, Lower ball 1 2 1 5666683 CUP, Lower worm bearing 1 22 5666681 WORM BEARING ADJUSTER 1 23 5676217 LOCKNUT, Worm bearing adjuster 1 24 5666887 BALL GUIDE 4 25 266800 BALLS 54 26 5666888 CLAMP, Bail guide 1 27 1 87375 SCREW, Ball guide clamp 1 28 7807009 BOLTS, Side cover 3 29 114495 LOCKNUT, Losh adjuster (0.4"-20 jam nut) 1 30 7802483 HOUSING SIDE COVER 8 BUSHING ASSY. 1 31 266903, 5, 7, 9 SHIM, Lash odjust 1 32 ** 48050-1 BEARING 1 33 53481 LINK 1 34 53482 ARM, Steering, front 1 35 ** 51449 RETAINER, Bearing 1 36 23315-2 SUPPORT. Steering column 1

09385 CLAMP, Cable 1 * COLUMN B GEAR ASSEMBLY part no.% ore saginow port no.'s.

** Note: Bearing 648050-1 was 53043 and Retainer #51449 was 53044. For Field Replacement of old bearing or retainer, order SK2360.

Find ... Go To..

32

Find ... Go To..

FIG. 19 - DRIVE MOTOR & RELATED PART5 STD. 265 M T H VICKERS PUMP


1 53084-3 HOSE - 2 5 3004 TUBE 3 53525A SUPPORT, Drive motor 4 53032 MOTOR, Drive

SKI 14OA SEAL KIT KEY NUT

7 53893 HUB 8 STUD ASSEMBLY 1 24338 STUD 5

8 51782 ELBOW 2 9 54217 CLAMP, Hose 1 10 39305 SCREW, Socket head (0.50" x 13 x 2.75") 4 "Ross Cornpan y Part Number.

, - -

Find ... Go To..

Find ... Go To..

FIG. 20 - SIDE BRUSH, MAIN BRUSH,&VACUUM FAN MOTORS

Ref. TENNANT No. Part No. Description

1 30013 WASHER 2 54274 ISOLATOR, Vibration 3 54722A BRACKET, Sidebrush valve mounting 4 48108A VALVE, Sidebrush shutoff, Gresen

SKI288 SEAL KIT 48 1 083 VALVE, Sidebrush shutoff, Dukes (cbsolete) SKI806 SEAL KIT

5 449 36 ELBOW, 45' 6 5 1 782 ELBOW 6.4 449 36 *ELBOW, 45D 6A 475 1 3 ELBOW, 4 5 O 7 321 65 ROD, Valve control 8 54194 ELBOW, 45' (no longer used) 9 10632-9 WASHER, Valve rod, rubber 10 46564 BUSHING (no longer used) 11 48108A-1 KNOB, Valve handle 12 47754 CONNECTOR 13 5 1 779 TEE 14 4751 8 CONNECTOR

Qty.

4

15 76835 CONNECTOR 16 77110 **MOTOR, Vacuum fan (includes hardware)

SK2561 SEAL KIT 17 50421 TEE 18 53083-6 HOSE 1 19 52908 HOSE 1 20 53083-1 8 HOSE 1 21 47542 MOTOR, Sidebrush, Ross 1

SKI694 SEAL KIT 1 47650-1 2 MOTOR, Sidebrush, Char-Lynn 1 SKI600 SEAL KIT 1

22 62302 *BLOCK, Porting 1 23 51403 *O-RING 2 24 5K2810 *MOTOR, Mninbwsh, Ross 1

SK7694 SEAL KIT 1 SK2810 "MOTOR, Mainbrush, Char-Lynn 1 SK16M) SEAL KIT 1

25 53083-2 *HOSE 1 26 53083-3 *HOSE 1 27 321 03 ***SEAL, Hose 1 28 53489 ***STRIP, Hose sea1 retaining 2 29 46607 +CONNECTOR 2 30 47721 +CONNECTOR 1 31 17400-1 1 +TEE 1 32 16463 HOSE 1 33 16473 HOSE 1 34 42226 ELBOW, 45' 2 35 82825 ELBOW 1 36 34423 MOTOR, Mainbrush, Char-Lynn 1 37 16474 HOSE 1 38 82799 SEAL, Hose 1 * Used on machines with serial number up to and including 9002. ** SK2560 replaces motor on mochines with S/N below 7700-Seal Kit i s SK2561 for both

*** Machines with serial number up to and including 6817, order SK2386. 1/84 + Used with obsolete vacuum fan moto before serial number 7700.

55

Find ... Go To..

Find ... Go To..

FIG. 21 - HYDRAULIC CYLINDER, VALVE &FILTER PARTS GROUP

Ref. TENNANT No. Part No. Description Qry . 1 5308 1-4 HOSE 1 2 15232 ELBOW I 3 +56820 ELBOW, Restrictor 1 3A C327.54 RESTRICTOR I 4 53477 CYLINDER, Dump (Std Green) Seal K i t SKI522 1

69330-5 CYLINDER, Dump (Alt Tennant) Seal K i t SK 1573 1 5 48929 CLEVIS 1 6 23788 RING, Retaining 2 7 23145 PIN, Clevis 2 8 78227 HEAT EXCHANGER 1 9 26395-1 CLAMP, Cable 1 12 53083-10 HOSE 1 13 53083-5 HOSE 1 14 47825 HOSE 1 15 54879 BRACKET, O i l filter mounting 1 16 53076 CONNECTCR 2 17 46011 ELBOW 2 18 6771 8 FILTER, Hydraulic oil (Std Deluxe) 1 19 6771 8-2 ELEMENT, O i l filter 1 20 533488 FILTER, Hydraulic oil (Alt Ripley) ( O - R i n g ~ ~ ~ 1 0 0 4 ) 1 2 1 53348-1 ELEMENT, O i l filter 1 22 05178 PLUG, O i l cwler 2 23 52908 HOSE 1

HOSE CONNECTOR (for Crass Valve use 53076) VALVE, Dukes

SEAL KIT ** VALVE, Obsolete Dukes

SEAL KIT **VALVE, Obsolete Cross

SEAL KIT ELBOW (use 56827 before serial no. 9003 ) ELBOW CONNECTOR, Dukes (obsolete Cross i s 42223)

*LINK, Valve handle *PIN, Clevis * PIN, Clevis * LEVER, Valve control

HOSE BEARING, Valve handle HANDLE, Valve control KNOB CONNECTOR, ( ~ l d style HEAT EXCHANGER, Old style (before y'n 8157) HOSE, Old stvle HOSE, Old sty le CLAMP, Hose PIN, Roll

*Machines with serial number up ta and including 7894, order SK2563. **To replace cbsolete valves, order SK2552. +Machines with serial number up to and including 8325, order SK2703

to replace connecrors.

1 /a4

Find ... Go To..

Find ... Go To..

FIG. 22 - HYDRAULIC TANK & RELATED PARTS MODEL 265


BREATHER, Hydmulic tank relief valve ELEMENT, Breather f i l ter

COUPLING NIPPLE COVER, Hydraulic tank GASKET, Cover, hydraulic tank TANK, Hydraulic CONNECTOR ELBOW CLAMP HOSE PLUG, Drain HOSE NIPPLE, Close STRAINER, O i l sump intake SCREEN, Hydraulic tank HOSE ELBOW PLUG, Fil ler WASHER TEE HOSE CAP, Fil ler breather COVER, Hydmulic tonk

* Used on machines with serial number up to and including 8972.

Find ... Go To..

FIG. 23 - VICKERS PUMP AND ?ELATED PARTS-STD.265 WITH VICKERS PUMP

Find ... Go To..

FIG. 23 - HYDRAULIC PUMP & RELATED PARTS-STD.265 WITH VICKERS PUMP


CLAMP, Wormdrive PUMP ASSEMBLY, HydmuIic o i l

ELBOW ELBOW 2 CONNECTOR 1 ELBO W 2 CONNECTOR 2 PUMP, Complete tandem 1

(For parts breakdown see "Hydraulic Components Section" CONNECTOR 1 ELBOW 1

A1

Find ... Go To..

Find ... Go To..

FIG. 24 - PUMP CGNTRCL LINKAGES 01 905


1 42240 PEDAL, Foot control 2 06474A PIN, Clevis

ARM 1 SUPPORT ASSEMBLY, Control rod R . H . 1

SUPPORT, Control rod 1 BEARING., Control rod 1

PIN, Clevis 1 ROD, Pump control 1 SUPPORT ASSEMBLY, Control rod L.H. 1

SUPPORT, Control rod 1 BEARING, Control rod 1

SPRING, Pump arm centering 6 SUPPORT, Pump centering spring 1 BALUOINT 4 ROD, Pump control 1 ARM, Pump control 1 BOLT. Hex CUD (0.25" - 20 x 1") 2 NUT 10 -25" - 20) 2 BRACKET, speed 1 irniter ARM . ..., .

KEY 1 SHOCK ABSORBER (no longer used) 1 MOUNT, Shock absorber 1

-, - .

Find ... Go To..

Find ... Go To..

Ref. No. -- 1 2 3 4 5

FIG. 25 - ELECTRICAL SYSTEM


4701 0 BUTTON, Horn 44078 SWITCH, Shaker 14137 SWITCH, Flashing-rotating ligh: (accessory) 24576 FLASHER, Flashing light (accessory) 62530 SWITCH, Ignition 62530-1 KEY, Ignition 54180 AMMETER 68222 LIGHT, O i l ressure indicating 37351 SWTCH, 0.P I pressure sending 5 1805 SWITCH, O i l pressure (LP machines only) 58536 ALTERNATOR 5491 1-1 5 RESISTOR, Bias (Ford) 54911-11 COIL, Ignition

24518 HOUR METER 28838 DAMPER, Hour meter 44080 BLOCK, Fuse 14215 FUSE, 20 AMP 54911-4 MOTOR, Starter SK2460 SOLENOID, Starter 29830-9 CABLE,Battery (positive) 371 83 BATTERY 40681-1 CABLE, Batiery (negative) GE1141 BULB, Spotlight 141 38A HORN 54121 MOTOR, Filter, shaker 53028-1 LEAD, Shaker motor 78005-2 SENDING UNIT, Temperature 50330 GAUGE, Tempemture 32 300 RELAY, Horn 14137 SWITCH, Light 47472 GAUGE, Fuel 47473 SENDING UNiT, Fuel gauge 54875A WIRE KIT LP 54418 B WIRE HARNESS 50302 WIRE HARNESS 241 08 LEAD, Shaker motor

Qty. -

5491 1-30 STRAP, coil 1 549 1 1-31 WIRE, High tension 1 50387 WIRE KIT, incl. wires: 12 &23 1 09385 CLAMP, Cable 1

1/84 4.5

Find ... Go To..

MCDEL 265 DECAL REPLACEMENT KIT 33638


24669 Decal, From Ai r Cleaner 51 368 Decal, Warning-Keep Radiator Fins Clean 48242 Decal, A1 ternator 53299 Decal, ThroftIe 47852 Decal, Caution, k t t e r y kads 19048 Decal, Gasoline Only 68223 Decal, Oil Temp 51 773 Decal, k i n Brush Lift 65072 (Hi-Dump only) Decal, Caution, Hopper 54517 Decal, Roll In-Out 231 44 (Sweepen) Decal, Tire Pressure 54299 (Scrubbers) Decal, Tire Pressure 55373 Decal, Caution-Safety Arm 54896 Decal, 265 46193 Decal, TENNANT, Blue green background 541 03 . Decal, Fitter Service 50310A Data Plate 37089 (Hi-Dump only) Decal, Caution, Travel Slowly 53920 Decal, Filter Shaker 47682 Decal, Valve 54918 Decal K i t (consists of '265' & 'TENNANT' ) 55375 (Hi-Dump only) Decal, Caution, Stay Clear 10735 Decal, Data Plate, UL Label, LP 45579 Decal, Factory Mutual, Type "G" 45580 Decal, Factory Mutual, Type "LP" 24049 Data Plate, LP 5491 1-7 Decal, Service tnformation 5491 1-6 Decal, Heavy Duty-Ford 4585 1 Decal, Hydruulic O i l 48088-6 Decal, Instructions 45742- 1 Decal, TENNANT, Black letters 45742-2 Decal, TENNANT, Black letters 24507 Decal, Caution, This Side Out 533488-2 Decal, Filter Element 50560-2 Decal for Pump 50560 53733-3 Decal for Motor 53733 53733-2 Decal for Motor 53733-1 62550-1 Decal for Valve 62550 69181-4 Decal for Pump 69181 47454 Decal, UL Type "Gas" 54135 (Std, only) Decal, Vacuum Attachment 24787 (Std . only) Decal, Windro Broom 46276 (Std. only) Decal, Scrubber 44695 (Std . on1 y) Decal, Scrubber instructions 46847 (Std. only) Decal, Detergent Recommended 50530-2 (Std. only) Decal for Pump 50530 24892 (Std. only) Data Plate, Machine Attachment, Scrubber 24892-2 (Std. only) Data Plate, Machine Attachment, Broom 24892-3 (Std. only) Data Plate, Machine Attachment, Snow 43566 (Std . on1 y) Decol, Water Control 62088 Decal, Caution - rotating fan 36603 Decal, Potent - power sweeper 47892 Decal. Caution

7/83 Find ... Go To..

CONTENTS PAGE

Fig. I - Main Fmme & Related Parts - - - - - - - - - - 2&3 Fig. 2 - Seat 8 Instrument Panel - - - - - - - - - - - - 485 Fig. 3 - Hopper Lift Arm Assembly- - - - - - - - - - - - 687 Fig. 4 - Stabilizer Safety Leg - - - - - - - - - - - - - - 889 Fig. 5 - Hopper 8RelatedPorts-- - - - - - - - - - - -1081 1 Fig. 6 - Dust Filter & Shaker Motor - - - - - - - - - - -128~13 Fig. 7 - Vacuum Fan Assembly - - - - - - - - - - - - - 14815 Fig. 8 - Engine & Related Parts- - - - - - - - - - - - - 16817 Fig. 9 - Gasoline Carburetor, Fuel Pump,

Governor & Related Po* - - - - - - - - - - - 1881 9 Fig. 10 - Gasoline Tank &Filter - - - - - - - - - - - - 2082 1 Fig. 11 - Air Cleaner & Related Parts - - - - - - - - - - 22823 Fig, 12 -CoolingSystem - - - - - - - - - - - - - - - - -24625 Fig. 1 3 - E x h a u ~ t S ~ s t e m - - - - - - - - - - - - - - - - -26827 Fig. 14 - Steering 8. Related Parts - - - - - - - - - - - -28829 Fig. 15 - Reor Wheel Drive Motor &

Support Parts Grwp - - - - - - - - - - - - - 30 Fig. 16 - Rear Drive Wheel Parts Group- - - - - - - - - 31 Fig. 17 - Front Meels & Bmkes - - - - - - - - - - - - - 32 &33 Fig. 18 - Side Brush Drive & Support- - - - - - - - - - -34835 Fig. 19 8 20 - Mdin Brush Drive - - - - - - - - - - - - 46-38 Fig. 21 - Model 265 Hi-dump Complete Hydraulics - - -39 Fig. 22 - Pump Assembly Group - - - - - - - - - - - -40841 Fig. 23 - Hyclmulic Tank Group- - - - - - - - - - - - -42843 Fig. 24 - Rollout Cylinders & Control Valve Group - - -448.45 Fig. 25 - Hopper Dump Cylinder & Its Control Valve- - 468.47 Fig. 26 - Main Brush, Side Bnrsh, Vacuum Fan Motor 8

Side Brush Control Valve - - - - - - - - - - - 48649 Fig. 27A - Heat Exchanger & Oil Filter (current) - - - 50 Fig. 27- Heat Exchanger & O i l Filter (obsolete) - - - - 51 Fig. 28 - Pump Control Linkage Parts Group - - - - - - 52853 Fig. 29 - Rear Drive Motor - - - - - - - - - - - - - - - 54 Fig. 30 - Electrical System for 265 Hi-dump - - - - - - 55&56

Find ... Go To..

Find ... Go To..

ORDERING REPAIR PARTS

To avoid errors or delays in filling parts orders, please BOLT AND CAP SCREW STRENGTH furnish allof the following information. tDENTlFlCATlON

1. Always specify the machine model number and the machine serial number shown on the machine data plate.

I SER. NO G W 3roLBS. 1 W KG.

1 MANUFACTURED SOLD AHD SERVICED BY

a TENNANT COMPANY

2. Give tho pan number, description, and the quantity needed of each item on the order. Do not order by reference number or the figure number of the illustrated parts.


4. If the old part cannot b% identified, send it to us with thequantity needed specifisdon theorder.

5. State definite shipping instructions to include the shipping address and/or the billing address if there is a ditference. Any claim for loss or damage to a shipment in transit should be filed promptly against the transportation company making the delivery. Shipments will be complete unless the packing listororder acknowledgement indicate items back ordered.

If parts received are suspected to be incorrect or defective, piease write, wire, or phone the Tennant Company representative from whom you ordered the part. They will give authorization for return and/or handle replacement shipments when required.

Metric equivalents have been included, where applicable, throughout this parts catalog.

Bolts and cap screws required to have high-strength qualities equivalent to SAE Grade 8 are identified throughout this catalog by the description GR 6. Unless identified by this description, all standard bolts and cap screws are SAE Grade 5.

Find ... Go To..

.-,

Find ... Go To..

FIG. 1 MAIN FRAME & RELATED PARTS

Ref. TENNANT No. Port No. Description Qty.

33505 53052 53974 23275 45857 *33762

23752-2 32368 36994 23384-2 23382

To replace order

SK2125 53298 53219 531 37 23268-1 09 342

**33760 10632-1 3

FRAME, Main SEAL, Brush door SEAL, Bwsh door SKIRT, Side RETAINER, Side skirt DOOR, Brush R.H. SHIM ( i f needed for weld-hinged door) ARM, ' ~ o ~ ~ e r stop safety PIN, Safety arm RETAINER, Side seal SEAL, Hopper side SEAL, Top pan SEAL, Top pan BRACKET, Top pan seal SKIRT, Rear ( Brush contact) ANGLE, Skirt rnwnt SKIRT, Rear (Floor contact) RETAINER, Rear skirt CHAIN, Static dmg DOOR Access L.H. GRO~MET, Lintel hose

23 23386 SEAL, Top pan 1 24 50447 BRACKET. Top pan seal 1

55373 DECAL, Safety arm 2 54918 DECAL KIT "TENNANT" 8 "265" 1

25 32885 HINGE, Brush door, R.H. 1 26 32886 HINGE, Brush door, L.H. 1

*To replace R.W. Brush door with welded on hinge, order SK2515; to reploce door with bolted on hinge used on machines up to serial number 8543, order SK2726.

**To replace L.H. Brush door with welded on hinge, order 5K2514; to replace dcor with bolted on hinge used on machines up to serial number 8543, order SK2724.

3

Find ... Go To..

Find ... Go To..

265 Fig. 2 - SEAT, INSTRUMENT PANEL & :-.ATEL7 ?A'TS

te f . T E N N A N T :*lo. pcfi P A - . - Ses;r;cti=r; ~ . . .~ . ~"...

5 EAT MrJs:.;;, SeG7

SUPPOST, Seat PLATE, Cover COVER, Battery BRACKET, Seat suppcrr PANEL, Acces$ PANEL, Instrument COVER, Engine panel DOOR, lnstmment panel 8 0 X , Instrument PANEL ASSEMBLY SEAL, Seat support ARM, Hinge ARM, Hinge HINGE, Engine cover HINGE, Side door DOOR, Side COVER, Engine PANEL, Corner GRILL COVER, Top rear BUMPER SLEEVE, Instrument box mounting BRACE BRACKET TREAD, Floor

Find ... Go To..

Find ... Go To..

265 FIG. 3 - HOPPER LIFT ARM ASSEMBLY


1 04733-5 PIN, Upper pivot arm 2 2 * 55203 ARM ASSEMBLY, Upper pivot R.H. 1 3 35529 BEARING, Journal 1 4 36988 CLAMP, Hose 2 4.4 36989 PAD, Rubber hose 2 5 3563 1 BEARING, Lift arm R.H. 1 6 23138 SHIM, Lift arm 1 7 35631 -1 BEARING, Lift arm L.H. 1 8 * 55204 ARM ASSEMBLY, Upper pivot L.H. 1 9 35529 BEARING, Jwrnol 1 10 36996 WASHER, Cam 2 1 1 3354 1 CAM, Splined 2 12 35512-1 ARM, Hopper l i f t 1 13 35561 BEARING, Journal 4 14 35629 WASHER 6 15 35640 SHAFT, Torque R.H. 1 16 3561 5 WASHER 6 17 *37139 BEARING, Thrust 6 18 32448 CHAIN & EYEBOLT ASSEMBLY 2

32440 CHAIN 1 11893 EYEBOLT 1

19 35621 -1 ARM ASSEMBLY, Front pivot R. H. 1 20 3556 1 BEARING, Journal 2 2 1 35665 BEARING, Journal 1 22 35666 BEARING, Thrust 2 23 356 14 WASHER 2 24 14242 NUT 2 25 35686 RING, Retuining 2 26 35636 SHAFT, Torque L.H. 1 27 35620-1 ARM ASSEMBLY, Front pivot L. H . 1 28 35665 BEARING, Journal 1 29 3556 1 BEARING, Journal 2 30 35630 BEARING, Center toque tube 1

35668 BEARING, Journal 1 3 1 35595 ROD, Tie 1

* Before serial number 6106, Arm Assembly, R.H. was 35645A; Arm Assembly, L.H. was 35645-3; Bearing 371 39 was 35667. To replace A m Assembly, R.H. on machines before serial number 6106, order SK2694. To replace Arm Assembly, L.H. on machines before serial number 6106, order SK2695.

7

Find ... Go To..

FIG. 4A - STABILIZER SAFETY LEG

(used on machines with serial number 7355 and above)


32286 STAB1 LI ZER LEG ASSEMBLY 1 1 35591 LEG, Safety 1 2 "33568 LEVER 1 3 23788-1 Rt NG, Retaining 1 4 51727 PI N, Clevis 2 5 14595-1 CLEVI S, Adjustable 1 6 **33563 ROD, Threaded 1 7 33763 PIVOT, Shaft 1 8 35533 SUPPORT, Safety leg 1 9 23788 RING, Retaining 1 10 369 72 PIN, Groved 1 11 35527 LINK 1 12 32282 BUMPER, L.H. 1 13 24528 BRACKET, "Lo 1 14 33523 SPRING, Tension 1 15 33565 LUG, Adjusting 1 16 32899 NUT 1 17 14895 SHIM 1

* Previous lever 32280 hos been replaced by SK2606 which olx, includes the new rod with spring adjustment.

** To replace old-style rod, order SK2607 which includes the improved spring tension design.

n

Find ... Go To..

FIG. 4 - STABILIZER SAFETY LEG (used on machines with serial number up to and including 7354


36997 LEG ASSEMBLY, Stabilizer 1 I 48968 SHAFT, Pivot 1 2 35533 SUPPORT, Safety leg 1 3 36972 PIN, Safety leg pivot 1 4 23788 RING, Retaining 1 5 35591 LEG, Stabilizer 1 6 35527 LINK 1 7 23524 LINK, Retaining 2 8 48954 PIN, Roller 1 9 45794 SHAFT, Roller 1 10 48957 ROLLER 1 1 1 14601 BALLJOINT 2 12 36971 STUD 1 - NUT, 0.25" - 28 1 13 45795 BRACKET, Roller shaft 1 14 45797 BUMPER 1

Find ... Go To..

FIG. 5 - HI-DUMP HOPPER AND RELATED PARTS

Ref. TENNANT No. Part N o . Description Qty .

1 48692 BUMPER 1 2 36984 BRACKET, Door latch 3 35588 NUT 4 04733-3 PiN, Hopper door pivot 5 35526 DOOR, Hopper . . 6 51727 PIN, Clevis 2 7 23146 *PIN, Roll, 0.18" OD, 1.62" long (old style) 1 7 46585 PfN, Roll, 0.18" OD, 1.38" lona (currentstyle) 1 - . , . 8 37074 *BRACE, Hbpper door . 1 9 28387 SPRING 1 10 23788-1 RING, Retaining 11 37073 *SHAFT, Hopper door latch trip 12 35546 SLEEVE 13 48930 ROLLER 14 3706 1 SEAL, Hopper door 15 10120 PIN, Clevis 16 37078 LATCH ASSEMBLY, L.H. 17 37079 LATCH ASSEMBLY; R.H. 18 48928 SPRING, R.H. 19 3281 1 DOOR, Fire 20 37021 LIP, Hopper side 21 36995 CAM 22 35540 SHIM 23 53758 RETAINER 24 35607 LIP, Hopper lower 25 48927 SPRING, L.H. 26 37057 **HOPPER 27 53698 HOOK. Fusible l ink . .. . .. .

28 46087 BRACKET, Fire door pivot pin 29 SKI511 LINK, Fusible 30 46088 PIN, Fire door pivot 31 28564 SPRING, Fire door

DOOR, f i r e BAFFLE, F i n door SEAL, Hopper cover CAPSCREW, (.312" - 18 x 1.375") NUT, (.312" - 18) WASHER, Springlock, (.312") HQOK, Fuse PIN, Fire door pivot SPRING, F i re door DOOR, Fire STRfP, Latch LATCH, Cover BRACKET, Hinge (not used on current machines) SUPPORT, Bumper STRIP, ~;bber,'bumper SPRING STRAIN RELIEF

* To replace old style hopper door brace, hopper door latch trip shaft, and ro i l pin, order SK2003.

** For machines with serial numbers less than 6070, order SK2060. 7/83 ** Used only on machines with serial numbers less than 6070.

Find ... Go To..

..

Fig, 6 - FILTER SYSTEM

Find ... Go To..

Fig. 6 - FILTER SYSTEM

Ref. TENNANT N o . Part No. Description Qtv.

*COVER, Filter box SEPARATORS BAG, Filter RACK, Bag BAR SHAKER MOTOR ASSEMBLY

STRAP, Shaker motor BAR, Rubber WEIGHT, Eccentric MOTOR, Shaker (sealed, not repaimble) SUPPORT STRIP. Rod clamp

ROD, Clamp, lower

* Note: Before Serial No. 3649, Filter Box Cover was X53339. For field replacement of 53338, order SK2349.

Find ... Go To..

Find ... Go To..

Fig. 7 - VACUUM FAN ASSEMBLY


CLIP, Vacuum housing MANIFOLD, Intake SEAL, 0.31 " x 30.50" (7.9 x 777 mm) IMPELLER HOUSING, Impeller ISOLATOR, Vibration PLATE, Motor mounting MOTOR, Vacuum fan (includes hardware)

SEAL KIT SLEEVE ADAPTER, Hose BRACKET, Hose adapter CLAMP, Worrndrive HOSE MUFFLER ASSEMBLY, Fan

MUFFLER, Fan SEAL, F m m rubber, 3.3" (84 mrn) SEAL, Faam rubber, 6.6" (168 mm) I NSULATI ON, Muffler, top I NSULATI ON, Muffler, side

WASHER, Flat, 0.38"

"Note: Before serial number 7701, vacuum f on motor was 53923. To replace 53923, order SK2560. Seal k i t for both motors i s SK2561.

Find ... Go To..

Find ... Go To..

Fig. 8 - ENGINE AND RELATED PARTS 01 899

Ref. No.

* NOTE: 7/82

TENNANT Part No. Description Qty.

51 176 DAMPER, Engine 3 54860 MOUNT, Engine, left hand 1 54959 SPACER, Alternator mounting I 54915 ALTERNATOR ASSEMBLY (including following) 1 54915-1 ALTERNATOR 1 5491 5-2 REGULATOR, Vol toge 1 549 15-3 FAN, Aiternator 1 50309 STRIP, Alternator bracket 1 54914 SHEAVE, Alternator 1 54928 BRACKET, Alternator mounting 1 32837 **ENGINE, Basic, Gasoline 1 50388 SCREW, Hex cap, 8mm 4 5491 1-10 PULLEY, Water pump 1 5491 1-30 STRAP, Coil (new strop not mounted on engine) 1 5491 1-11 COIL, Ignition 1 5491 1 -9 PULLEY, Crankshoft 1 4456 1 V-BELT, Altemtor-water pump 1 50854 V-BELT, Fan, radiator I 5491 1 -1 5 *RESISTOR, Ignition coil 1 54892 MOUNT, Engine, right hand 1 54889 BRACKET, Motormount 1 50335 NUT, Hex, 5mm 1 32453 *STARTER, Engine 1 5491 1-5 'RING, Starter locating 1 5491 1-16 *PIN, Dowel 2 53531 -2 COUPLING, Chain, (Engine side) 1 54836 A BRACKET, Motor 8, valve mount 1 54921 A-1 HOUSING, Flywheel 1 15280- 1 BUSHING (Key No. 00926) 1 53386-1 COUPLING, Chain, half (pump side) 1 53392-3 CHAIN, Coupling 1 47933 PLATE, Pump drive adaptor I 29832-7 CABLE, Grounding 1 50352 CAP, O i l filler & breather 1 5491 1 -26 *DIPSTICK, O i l level 1 549 1 1 -27 *TUBE, Dipsfick 1 50353 ELEMENT, Engine oil f i l ter 1

47854 SHIM (16-GA thick) as req . 47854-1 SHIM (0.19" thick) as req. 5491 1-31 WIRE, High tension, coil to distributor 1 5 1564 WASHER, Engine mounting 1 5491 1-32 "DRAIN CCCK, Blcck

Basic engine 32837 replaces engine 54912-1 on machines with S/N 7514 and above. To replace previous engine 54912-1, order SK2493. Basic engine does not include aiterncltor, voltage regulator, V-belts, fan, carburetor, pulleys, coil, resistor, etc. These paris are included in bosic engine 32837.

..,

Find ... Go To..

Old Style

fig. 9 Gasoline Carburetor, Fuel Pump, Governor and Related Parts

Find ... Go To..

265 Fig, 9 - GASOLINE CARBURETOR, FUEL PUMP, GOVERNOR 8 RELATED PARTS


CLAMP 2 LEVER, Throtile 1 HOSE, Air intake (new one-piece molded type) 1 AIR-HORN, Carburetor 1 GASKET, Carburetor to oir horn 1

*CARBURETOR, Gasoline (Repair k i t i s 38501) 1 ELBOW, Fuel inlet 1 CLAMP, Wormdrive 2 HOSE, Gasoline, 0.31" x 16" (7.9 x 406 mm) 1 GASKET, Carburetor 3 PLATE, Carburetor spacer 1 HOSE, Rubber, governor to distributor 1 ,O. 16"x 12"(4 x 305 mm) furnished with engine

CONNECTOR 1 GOVERNOR, Speed 1 STUDS, 1.31" - 1 8 x 3.3811(33 - 1 8 x 86 mm) 2 PUMP, Fuel (Gasaline only) 1 SPRING, Throttle return 1 BALLJOINT 1 CABLE ASSEMBLY, Choke 1 ROD, Throttle 1 BALLJOINT 1 PIVOT, Arm I CLAMP, Stop, throttle control 1 SCREW, 0.25" - 20 x 1.75" 1 ELBOW, Barbed 1 HOSE 1 SLEEVE, Stud 2

* To replace "Old-style" Carburetor, order SK2.588.

'* Ford Part Number +Previous air intake hose (#50331) included a spring (*53349) inside i t - To replace this hose with the new molded type, order SKI844

Find ... Go To..

FIG. 10 - GASOLINE TANK & FILTER

7/83

Find ... Go To..

265 FIG. 10 - GASOLINE TANK & FILTER


TANK, Gas STRAP, Gas tank CLAMP, Hose, worm dirve HOSE, Rubber CLAMP, Hose GAS LINE ASSEMBLY NIPPLE STRAINER & SEDIMENT BOWL, FueI NIPPLE CAP, Gas (includ. in item 1)

12 5301 4 SHIELD, Gosoline 13 23826 SEAL, Seat support

3 1

Find ... Go To..

PARTS

Find ... Go To..

265 Fig. 11 - AIR CLEANER AND RELATED PARTS


1 26509 NUT, Wing , 0.25" - 20 1 2 41178 WASHER , Steel 1 3 23791 B COVER, Air cleoner 1 4 4659 1 NUT, Wing, 0.25" - 20 1 5 24924 WASHER, Nylon 1 6 54081 COVER, Air cleaner 1 7 2731 3 ELEMENT, Air filter, inner 1 8 23792 ELEMENT, Air filter, outer 1 9 54082 STUD 1 10 54080 FLANGE, Air cleaner 1 11 23731 WASHER, Necprene 1 12 23727A-2 BASE, Air cleaner 1 13 47388 ELBOW 1 14 54148 HOSE, Breather 1 15 54333 r CLAMP 2 16 51706 * SLEEVE 1 17 4681 8 CIAMP, Wire 1 18 54155 * ELBOW, Rubber 1 19 3351 8 WASHER, Rubber 1 20 24669 DECAL, Fmm air cleoner 1

* Note: Used on old style air cleaner only.

Find ... Go To..

Find ... Go To..

f i g . 12 - COOLING SYSTEM 01900

Ref. TENNANT No. Part No. Description qk .

CAP, Radiator CLAMP, Wormdrive RADIATOR DAMPER, Radiator, vibration TUBE, Radiator HOSE, Radiator, (To engine) FAN (4-blade) PULLEY, Fan RING, Retaining BEARING & SflAFT, Fan ARM, Fan, mounting BRACKET, Fan, arm mounting SPRl NG PIN, Roll SHROUD, Fon DRAIN, Radiator ongle COUPLING NIPPLE HOSE, Radiator, Upper BOLT, E y e HOSE, Radiator (Bottom) BRACKET, Support BRACKET, Spr i ng

+ BRACKET, Tur nbuckl e +TURNBUCKLE, Be! t t ensi oni ng

*To replace radiator on rnochines with sen'ol number up to and including 7587, order SK2487. Machines with serial number from 7588 to 8157 use SK2676.

**~achiner with serial number up to and including 7587 used h c ~ e 10323-6. To replace 10323-6, order SK2544.

+Note: Machines with serial number up to and including 8132 rrsed the old style turnbuckle tensioning. To replace with the new spring temioning, order SK2564.

Find ... Go To..

Find ... Go To..

Fig. 13 - EXHAUST SYSTEM 01 896


PAD, Rubber ISOLATOR

'BRACKET, Muffler support *SUPPORT, Muffler SPACER PIPE, Tail CLAMP, Muffler SHIELD. Muffler, heat

MUFFLER CLAMP, Muffler

** PIPE, Exhaust CLAMP, Muffler

** BRACKET, Exhaust tube BRACKET, Exhaust tube GASKET, Exhaust manifold, end GASKET, Exhaust manifold, center MANIFOLD, Engine exhaust GASKET STUD NUT

** PIPE, Exhaust HANGER KIT, Muffler, includes items:

2, 3, 4, and 5 "MANIFOLD KIT, Replacement, includes items:

12 through 22 *BRACKET, Exhaust pipe *BRACKET, Exhaust pipe *PIPE, Exhaust

* Applicable to machines with serial number up to 7032

** TO replace fhese parts on machines with serial numbers up to and including 8132, order SK2565

-- Find ... Go To..

Find ... Go To..

265 Fig.14 - STEERING 8 RELATED PARTS

Ref. TENNANT No. Part NO. Description Qty.

1 47010 BUTTON, Horn 1 2 4701 1 BRUSH UNIT, Horn 1 3 47008 WHEEL, Steering 1

47007 * COLUMN 8 GEAR ASSEMBLY 1 4 114496 NUT, Steering wheel (0.50"- 20 jam nut) 1 5 264832 SPRING 1 6 5695951 BEARING & CABLE ASSEMBLY 1 7 264831 SEAT, Spring 1 8 5695956 COLUMN 1 9 103868 PLUG, Filler 1 10 5692532 HOUSlNG 1 11 7802482 ADJUSTER, Lcrsh 1 12 781 2838 SECTOR AND SHAFT ASSEMBLY 1 13 266316 BUSHING, Sector shaft 1 14 566734 GASKET 1 15 7801626 SEAL 1 16 5666683 CUP, Upper worm bearing 1 17 5666693 BEAR1 NG, Upper boll 1 18 5695954 WORMSHAFT 1 19 5666886 NUT, Ball 1 20 5666693 BEARING, Lower ball 1 21 . 5666683 CUP, Lower worm bearing 1 22 5666681 WORM BEARING ADJUSTER 1 23 567621 7 LOCKNUT, Worm bearing adjuster 1 24 5666887 BALL GUIDE 4 25 266800 BALLS 54 26 5646888 CLAMP, Boll guide 1 27 187375 SCREW, Ball guide clamp I 28 7807009 BOLTS, Side cover 3 29 1 14495 LOCKNUT, Lash adiuster(0+44"-20 jam nut) 1 30 7802483 HOUSING SIDE COVER & BUSHING ASSY. 1 31 266903, 5, 7, 9 SHIM, Lash adjust 1 32 ** 48050-1 BEAR1 NG 1 33 53481 LINK 1 34 35618 ARM, Steering, front 1 35 ** 51449 RETAINER, Bearing 1 36 23315-2 SUPPORT, Steering column 1

09385 CLAMP, Cable 1 * COLUMN 8 GEAR ASSEMBLY part no.% are Saginaw port no.ls.

**Note: Bearing $48050-1 was 53043; Retainer #51449 was 53044. For Field Replacement of old bearing or retainer, order SK2360.

Find ... Go To..

FIG. 15 - REAR WHEEL DRIVE MOTOR 8, SUPPORT PARTS GROUP

Ref. TEN NANT No . Part No. Descritpion - __L?.!.L-

N U T 1 WASHER 1 BEARING & CONE ASSEMBLY, Motor support 1

(includes 2 bearings & 2 cones) PIN, Support 1 SUPPORT 1 BAR, Hose support 1 SCREW, 0.50" - 13 x 2.75" (12.7 - 1 3 x 70 rnm) 4 MOTOR,Drive 1

SEAL KIT 1 HUB ASSEMBLY, Drive wheel 1

STUD 5 LINK, Steering 1

Find ... Go To..

FIG. 16 -REAR DRIVE WHEEL PARTS GROUP

Ref. TENNANT N o . Part N o . Description Qty.

47550 WHEEL ASSEMBLY 1 5381 8 RIM 2 47525 TIRE, 570/500-8, 6 ply) 3 53819-1 TUBE. Inner tire 570/500-8

45786 CAP, Valve stem 4 53819-2 FLAP, Tire-tube 5 24339 NUT, M e e l

Find ... Go To..

Find ... Go To..

265 FIG.17- FRONT WHEEL & BRAKES


1 3691 3 BRAKE, Parking 1 2 18141 PIN, Roll 1 3 23529A STRAP 1 4 071 42 PAD 1 5 35676 SHAFT, Broke 1 6 14605 PIN, Clevis, 0.25" x 0.75" (6.4 x 19 mm) 1 7 14595-1 CLEVIS, Adjustable 1 8 23483-2 ROD, Adjusting 1 9 0309 1 SPRl NG 1 10 28296 PIN, Clevis , 0.25" x 0.50" (6.4 x 12.7 mm) 1 11 23280-2 HANGER 1 12 23758-1 SHIM, Hanger as req .

* 1 9966 AXLE ASSEMBLY 2 13 23484 ARM 1 14 **I9965 AXLE & BUSHING ASSEMBLY 1 15 24992 BUSHING 1

20021 PIN, Roll 1 16 23272 CAM 1 17 10413 PIN, Threaded 1 18 1041 5 SPACER 1 19 10414 SHOE, Bmke (2 per wheel) 2 20 09758 SPRING, Tension 1

48076 WHEEL ASSEMBLY, Front 2 21 1 3534 BEAR1 N G 2 22 23244 RING, Retaining 2 23 23332 HUB 1 24 09006 SPACER 1 25 24120 TIRE B RIM ASSEMBLY 1

25193A WHEEL ASSEMBLY 1 25197A TIRE, Fmnt, solid (bonded to rim) 1

* Ta replace axle assembly on machines with serial number up b and including 8331 order SK2604.

**To replace axle and bushing assembly on machines with serial number up to and including 8331 order SK2603.

Find ... Go To..

FIG. 18 - SIDE BRUSH DRIVE d SUPPORT

Find ... Go To..

265 Hi-Dump FIG. 18 - SIDE BRUSH DRIVE & SUPPORT PARTS CROUP

Ref. TENNANT No. Port No. Descriotion

1 3699 3 PIN 2 23788 RING, Retaining 3 36958 BUMPER, Side brush arm 4 48951 -1 PLATE, Bumper end 5 36986 PLATE, Bumper end 6 55662 ARM, Side brush 7 23191 PIN, Clevis 8 26 156 KNOB 9 35649 HANDLE

~ - - ~ - . , ~ . - ~

1 1 23307-1 LEVER, Lift hclndle 12 23294 CABLE ASSEMBLY, Side brush l i f t 13 23306-1 BRACKET, Clip 14 14174 SPRING 15 22143 SPACER 16 23503A YOKE, Side brush l i f t 17 23536 PIN, yoke pivot 18 53773 BRACKET, Bumper 19 53826 BUMPER 20 53772 MOUNT, Side brush motor 21 47501 ADAPTER, Side b ~ s h

Qty.

1 1

7/83 2;

Find ... Go To..

Find ... Go To..

37

Find ... Go To..

265 FIG. 19 & 20 - MAIN BRUSH LIFT CONTROLS & MAIN BRUSH DRIVE


KNOB HANDLE LEVER, Lift handle SPRING NUT , 0.50" - 20 CLIP ROD, Lift ARM, Lift SEAL PIN BRACKET, Clamp CLAMP, Cable hold down KNOB, Brush height adiusting NUT, Wing , 0.50" - 13 ROD, Lift BRACKET, Countershaft bearing FLANGE, Countershaft bearing BEARING. Countershaft PIN, Roll, 0.31" x 1.88" (7.9 x 48 mm) ARM, B ~ s h L.H. P L U ~ , B ~ s h drive SHAFT, Counter ARM & PLUG ASSEMBLY, Brush R.H.

WASHER RING, Retaining BEARING, B ~ s h idler plug PLUG, Brush idler ARM, B N S ~ R.H. PLUG, Threaded dust, 0 .SO" - 13

HUB, Countershaft end

+ Note: Bracket 950521 was 531 32; Flange 635973 was 53879 and Bearing #23624-1 was 53878, For Field Replacement of former parts order SK2361

Find ... Go To..

265 HI-DUMP N T H VICKERS PUMP

Find ... Go To..

F I G . 22 - VlCKERS PUMP and FITTINGS PARTS

Find ... Go To..

FIG. 22 - VICKERS PUMP AND FITTINGS


1 29696 ClAMP 2 47696 ELBOW 3 51787 ELBOW 4 47516 CONNECTOR 5 4786 1 "PUMP, Complete tandem (Vickem)

* SKI 344 SEAL KIT , Complete 6 50430 CONNECTOR 7 47934 CONNECTOR 8 53076 ELBOW 9 56827 ELBO W 10 475; 7-1 HOSE

*NOTE: Shoft seal kit is SK1345.

Find ... Go To..

FIG. 23 HYDRAULIC TANK PARTS GROUP

Find ... Go To..

FIG. 23 - HYDRAULIC TANK PARTS GROUP


1 *53430 VALVE ASSEMBLY, Breather & Relief *53431 ELEMENT, Breather

2 " 1 0222 COUPLING 3 *lo221 NIPPLE 4 56322 HOSE 5 *48117 PLUG, Filler 6 *06507 ELBOW 7 'SK2720 COVER, Hydraulic fank 8 33753 GASKET 9 *50022 WASHER I 0 *48086 SCREEN, Tank filler 1 1 54873 TANK, Hydraulic fluid 12 5 1 885 SCREEN, Tank sump 13 02546 Nl PPLE, Sump screen 14 46.480 CONNECTOR 15 47695 ELBOW 16 40362 PLUG, Tank dmin 17 32375 HOSE 18 29696 CLAMP 19 53083T04 HOSE 20 34369 TEE 21 34306 CAP, Filler breather 22 33574 COVER, Hydmulic tclnk

" Used on machines with serial number up to and inclding 8972.

Qty.

Find ... Go To..

FIG. 24 - ROLLOUT CYLINDERS & CONTROL VALVE GROUP

44

Find ... Go To..

FIG. 24 - ROLLOUT CYLINDERS 8 CONTROL VALVE GROUP


PIN, Clevis RING, Retaining RING, Retaining PIN CYLINDER ASSEMBLY REPLACEMENT KIT CYLINDER ASSEMBLY, Rollout

CYLINDER REPLACEMENT KIT CYLINDER, Rollout

SEAL KIT ELBOW, 4 5 O CLEVIS

BEARING, Jourml HOSE HOSE KNOB HANDLE LINK, "5" hook PIN, Clevis VALVE, Cylinder control

SEAL KIT ELBOW CONNECTOR ELBOW TEE

RESTRICTOR FITTING REPLACEMENT KIT

* For machines with serial number up to and including 3229. ** For machines with serial number up to and including 3229. (This k i t contains

two cylinders - it i s necessary to replace both.)

+ For machines with serial number up to and including 8327.

45

Find ... Go To..

Find ... Go To..

FIG. 25 - DUMP CYLINDER & ACCESSORIES CONTROL VALVE Ref. TENNANT No. Part No. Description QY-

1 47825 HO SE 1 2 52374 HOSE 1 3 35515 PIN, Dump cylinder pivot 1 4 23788 RING, Retaining 3

*39206 CYLINDER ASSEMBLY, Dump 1 5 50421 TEE 1 6 35587 CONNECTOR 1 7 +5&20 EMOW 1 7A +32754 RESTRfCTOR 1 8 48981 CYLINDER, Dump 1

SK 1805 SEAL KIT 1 9 -32942 CLEVIS, Dump cylinder 1 10 35688 BEARING, Clevis iournol 2 11 23145 PIN, Dump cylinder clevis 1 12 51 753 HOSE 1 13 53083-6 HOSE 1 14 46480 CONNECTOR, In-port I

42223 CONNECTOR, In-~ort (used with Cross valves) 1 VALVE, Dukes

SEAL KIT **VALVE , Obsolete C m s

SEAL KIT **VALVE , Obsolete Cross

SEAL KIT ** VALVE, Cbsolete Dukes

SEAL KIT CONNECTOR ELBOW, Ou t -~o r t (used with Cross Valves) ELBOW (use elbow 56827 before S/N9003 ) ELBOW HOSE HOSE (use hose 53083-3 before S/N 9003 ) LINK, Connecting PIN, Clevis PIN, Clevis

PIN, Roll

+Machines with serial number up to and including 8326, order SK2703. *Machines with serial number u to and including 7777, order SK2555 for replacement

of Cylinder assembly. To rep i' ace clevis on mochines with serial number up to-and including 7777, order SK2554.

*Machines with serial number up to and including 7899 used old-style linkoge. To replace former design, order SK2563.

**To replace obsolete valves, order SK2552.

Find ... Go To..

"Old style" !r', :..a vacuum fan -...

motor 53923 ,&.? ; (replaced by SK2560)

&-5

"Old style" main brush motor replaced by SK2810

Find ... Go To..

FIG. 26 - MAIN BRUSH, SlDE BRUSH &VACUUM FAN MOTORS &CONTROL VALVE

TENNANT Ref. No. Pari No. Description Qty.

1 76835 CONNECTOR 1 2 5 1 779 TEE 2 3 47518 CONNECTOR 2 4 7iI 10 **MOTOR, Vacuum fan (includes hardware) 1

SKZ561 SEAL KIT 1 5 46607 CONNECTOR (old style) 2 6 17400-1 1 TEE (old style) 1 7 4772 1 CONNECTOR (old style) 1 8 541 94 ELBOW, 45' (no longer used) 1 9 53083-1 HOSE 1 10 5042 1 TEE 1 11 53083-6 HOSE 1 12 47542 MOTOR, Side brwsh (Rw) 1

SKI 694 SEAL KIT 1 47650-12 MOTOR, Side brush (CharLynn) 1 SKI600 SEAL KIT 1

13 46480 CONNECTOR 2 14 54044 TUBE, Side brush motor 2 15 53083-1 8 HOSE 1 16 SK28lO ***MOTOR, Main brush (Ross) 1

SKI694 SEAL KIT 1 SK2810 ***MOTOR, Main brwsh (CharLynn) 1 SKI600 SEAL KIT 3

17 51403 ***O-RING 2 18 62302 ***BLOCK, Porting 1 19 53083-2 ***HOSE 1 20 321 03 *SEAL, Brush wrap hose 2 2 1 53489 STRIP 1 22 449 36 ELBOW, 4.5' 1 23 51782 ELBOW 1 23A 449 36 ***ELBOW, 45' 1 23A 475 1 3 ELBOW, 45' 1 24 48108A VALVE, Side brush shut-off (Gresen) 1

SKI 288 SEAL KIT 1 48108B VALVE, Side brush shut-off (Dukes) 1 SKI 806 SEAL KIT 1

25 30013 WASHER 4 26 54722A BRACKET, Valve mounting 1 27 54274 ISOLATOR, Vibration 2 28 56322 HOSE 1 29 321 65 EXTENSION, Valve handle 1 30 10632-9 GROMMET 1 31 46564 BUSHING (no longer used) 1 32 481 08A-1 KNOB, Valve handle 1 33 82799 SEAL, Hose 1 34 16463 HOSE 1 35 42226 ELBOW, 4S0 2 36 82825 ELBOW 1 37 1 6474 HOSE 1 38 34423 MOTOR, Main brush (Char-Lynn) 1

SKI600 SEAL KIT 1 * To replace previous seal used on machines before serial number 6818, order SK2386 ** SK2560 replaces motor on machines with S/N below 7700-Seal Kit i s SK2561 for both.

1/84 *** Used on machines with serial number up foand including 9002. 49

Find ... Go To..

FIG. 27A - HEAT EXCHANGER & O I L FILTER (For machines with s/n 8157 and above)


1 78227 EXCHANGER. Heat 1 , 2 54879 BRACKET, Oil fi lter mounting 1 3 53076 ELBOW 2 4 6771 8 FILTER ASSEMBLY, Hydraulic fluid (std. Deluxe) 1 5 * 6771 8-2 ELEMENT, O i l f i l ter (std. Deluxe) 1 6 52908 HOSE 1 7 53083-5 HOSE 1 8 05 1 78 PLUG 9 53083-1 0 HOSE 10 4661 1 ELBOW 11 26395-1 CLAMP, Hose

"Note: Either Deluxe Products or Ripley filters may be used . The element part number i s printed on the element.

50

Find ... Go To..

Alternate cartridge -

To Vocuum Fan Motor

FIG. 27 - HEAT EXCHANGER & OIL FILTER (For machines with Jn up to and including 8156)


1 53086 EXCHANGER, Heat 2 542 1 4 BACKING, Clamp 3 54492 HOSE, Split 4 54493 CLAMP 5 52908 HOSE 6 51753-1 HOSE 7 42223 CONNECTOR

Qty.

9 54879 BRACKET, O i l filter mounting 1 10 53076 ELBOW 1 1 1 53083-3 HOSE 1 12 6771 8 FILTER ASSEMBLY, Hydraulic o i l (Std Deluxe) 1 13 67718-2 % ELEMENT, O i l f i l ter (Std. Deluxe) 1 14 533488 FtLTER ASSEMBLY, Hydmulic oil (A l t Ripley) 1 15 53348-1 +6 ELEMENT, Oi l fi lter (Al t Ripley) 1

(0-Ring for filter i s DH1004) *NOTE: Either Deluxe Products or Ripley filfers may be used. Please check your machine before ordering filter elemenk. The element port number i s printed on the element.

12/80 51

Find ... Go To..

Find ... Go To..

FIG. 28 - PUMP CONTROL LINKAGE 01 905

Ref. TENNANT No. Part No. Description Q ~ Y -

1 42240 PEDAL. Foot control 1 PIN, &is ARM SUPPORT ASSEMBLY, Control rod R.H.

SUPPORT, Confml rod BEARING, Control rod

PIN, Clevis SUPPORT, Follower cam ROD, Pum control P CAM, Fol ower SUPPORT ASSEMBLY, Control rod L. H.

SUPPORT, Control rod BEARING, Control rod

SPRING, Pump am centering SUPPORT, Pump centering spring BALLJOINT ROD, Pump control ARM, Pump control BOLT, Hex cap, 0.25" - 20 x 1 " NUT, 0.25" - 20 BRACKET, Speed limiter ARM, Shock absorber mounfing KEY SHOCK ABSORBER (no longer used) MOUNT, Shock absorber (no longer used) BALLJOINT, Shock absorber (no longer used)

Find ... Go To..

FIG. 29 - REAR DRlVE MOTOR

Ref. TENNANT No. Port N o . Description Q ~ Y

1 53084-3 HOSE 2 2 53004 TUBE 2 3 39305 BOLT, Socket head , 0.50" - 13 x 2.75" 4 4 53525A SUPPORT. Rear drive motor 1

~ -~

5 37041 ** M O T O R , < R ~ ~ ~ drive SKI951 SEAL KIT

6 *039027 KEY 7 W25126 NUT 8 53893 . HUB AND STUD ASSEMBLY 9 51 782 ELBOW I0 542 17 SUPPORT, Hose

*Ross Company part number

**For parts breakdown, see "HYcImuIic Componenk" section.

Find ... Go To..

Find ... Go To..

FIG. 30 - ELECTRICAL SYSTEM 265 HI-DUMP

Ref. TEN NA N T No. - Part No. Descripticn Qty.

--

1 4701 0 BUTT0 N, Horn 1 2 44078 SL'dTCH, Shaker 1 3 14137 SWITCH, Flashing-rotating light (accessory) 1 4 24576 FLASHER, Flashing light (accessory) 1 5 62530 SWITCH, Ignition 1

62530-1 KEY, Ignition 1 6 54180 AMMETER 1

LIGHT,-oil ressure indicating 1 SWITCH, 0.7 I pressure sending 1 SWITCH, O i l pressure (LP machines only) 1 ALTERNATOR (does not include fan 1 RESISTOR, Bias 1 COIL, Ignition 1 WIRE K i I, includes wire 23 1 METER, Hour 1 DAMPER, nour meter 1 BLOCK, Fuse 1 FUSE, 20 AMP 5 MOTOR, Starter 1 SOLENOID, Starter CABLE,Bottery (paitive) BATTERY CABLE, Battery (negative) BULB, Spotlight WORN MOTOR, Filter, shaker LEAD, Shaker motor SENDING UNIT, Tempemture GAUGE, Temperature RELAY, Horn SWITCH, Light GAUGE, Fuel SENDING UNiT, Fuel gauge WIRE KIT LP WIRE HARNESS WIRE HARNESS LEAD, Shaker motor

* See Ford park section for Ford part numbers.

Find ... Go To..

Descri~t ion Paoe

. . . . . . . . . Fig. 1 - Parts Required for Scrubbing 1 Fig. 2 - Tank Holder Frame . . . . . . . . . . . . 2.a 3 Fig. 3 - Pickup and Detergent Tanks . . . . . . . . . 4 & 5 Fig. 4 - Rear Squeegee . . . . . . . . . . . . . 6 8 7 Fig. 5 - Main Scrub B ~ s h . . . . . . . . . . . . 8 6 9 Fig. 6 - Detergent Solution Control . -10 8 11 Fig. 7 - Side Scrub B N S ~ & Squeegee . 12 & 13 Fig. 8 - Headlights, Taillights & Spotlights Kits . .14 & 15 Fig. 9 - Revolving Light K i t . . . . . . . 16 & 17 Fig. 11 - Bmke Light Ki t . . . . . . . . . . . . . . . 18 Fig. 12 - Overhead Guard K i t . . . . . . . . . . . . . 19

. . . . . . . Fig. 13 - Overhead Gwrd K i t (Hi-Dump) 20 Fig. 14 - Sweeper Cab K i t . . . . . . . . . . 21 & 22 Fig. 15 - Hi-Dump Cab K i t . . . . . . . . . . . 23 824 Fig. 16 - Scrubber Cab K i t . . . . . . . . . . . 25 8.26 Fig. 17 - Side Brush Dust Control . . . . . . . . 27 828 . . . . . . . . . . . Fig. 18 - Vacuum Wand K i t 29 &30 . . . . . . . . . . . . . . . Miscellaneous Kits 31 - 33 Accessories Not l l l ustmted . . . . . . . . . . . 34

Find ... Go To..

Find ... Go To..

FIG. 1 - PREP FOR SCRUB KIT 02327

Ref. TENNANT No. Part No, Description Qty.

45740 PREP FOR SCRUB KIT 1 1 47525 TI RE 1 2 48076 TIRE A N D W H E E L ASSEMBLY 2 3 25197A TIRE, Solid 1 4 54299 DECAL, Tire pressure 1 5 46093 EXTENSION, Side brush arm 1 6 43346A GUARD, Motor 1

FITTING, E I ~ O W

COUPLING, Male COUPLING, Female FITTING, Straight FlTTl NG, Straight FITTING, Elbow 0-RI NG

ARM,. Sidebrush BUMPER

* Used on machines with serial number up to and including 9002. ** Used on factory installed scrubbers only.

Find ... Go To..

Fig. 2 - TANK HOLDER FRAME

2

Find ... Go To..

Fig. 2 - TANK HOLDER FRAME

Ref. TENNANT Na . Part No. Description Qtv . 1 04428A SPRI NG 4 2 1 1048 FITTING, Grease 2 3 201 60 PIN, Rolf 0.13" x 0.63" (3.3 x 16 mm) 4 4 26065 BUSHING 2 5 26565 KNOB 4 6 43004 PICKUP TROUGH 1 7 43005 TROUGH SUPPORT 1 8 32449 PIN 4 9 43030 BRACKET, Pin 4 10 43614 FRONT LEG 2 11 43615 REAR LEG 2 12 43039 SUPPORT 2 13 43079 ACCESS PANEL 1 1 3.4 43192 CAM, Pan adjusting 1 14 43203 CHAl N 1 15 43616 CASTER 4 16 43287 LID 2

18 43363 HOOK 19 53368 SHIELD, Spray 20 53371 BUMPER 21 43564 MAIN FRAME 22 43609 BUSH t N G

54289 BAG ASSEMBLY,. Wrench 23 43249 SUPPORT, L. H .

Find ... Go To..

FIG. 3 - PICKUP AND DETERGENT TANKS PARTS GROUP 7/82

4

Find ... Go To..

FIG. 3 - PICKUP & DETERGENT TANKS PARTS GROUP

Ref. TENNANT No. PART No. Description Qty.

SCREW SCREEN SEAL, Lid GASKET, How Outlet CONNECTOR, Tank hose TANK, Detergent BRACKET, Flexible hose ( incl HOSE, Flexible CLAMP COLIAR, Float gouge BALL, Float GUIDE, Float ball GASKET

f43805 gasket)

PLUG BRACKET, Tank mounting, R.H. BRACKET, Tank mounting, L.H. DRAIN HOSE ASSEMBLY

CUFF, Hose CLAMP

f COVER ASSEMBLY, P i ck-up tank PLATE, Sealing SEAL. D w r cleanout LOCK, cam NUT, Wing

*TANK, Water pick-up VACUUM HOSE ASSEMBLY,

CUFF, Hose CUFF, Pickup

STRAP, Hose retainer CLAMP, Hose VACUUM HOSE ASSEMBLY,

CUFF, Hose BOLT, Pick-up tank FlANGE TUBE, Tank locating

Rear

Bottom

*Note: Machines with serial number up to and including 17901 used old-style metal recovery tank 430078 and cover assembl y 43579.

Find ... Go To..

Fig. 4 _ REAR SQUEEGEE

Find ... Go To..

Fig. 4 - REAR SQUEEGEE

Ref. No.


PIN, Clevis- 0.37" x 1 -00'' PIN, Cotter, 0-09" x 0.75" ( 2 . 3 ~ 19 mm) PIN, Roll, 0.25" x 1 .SO" (6.4 x 3.8 mm) PIN, Rofl, 0.38" x 1 .5UN (9.7 x 38 mm) PIN REAR SQUEEGEE SUPPORT ASSEMBLY

Clevis P i n Pivot Squeegee Link

SQUEEGEE LlNK ASSEMBLY REAR SQUEEGEE ASSEMBLY

Squeegee frame Blade, squeegee Backing Strip Retainer Refuiner Nmr le Pin Clamp

STOP, Adjustable

SUPPORT PIVOT, Squeegee l i f t BUSHING, Flange BRACKET, Arm pivot ARM, Squeegee lift HANDLE LlNK CROSS SHAFT PIVOT, Cross shaft PIN, Clevis RFAR SQUEEGEE LIFT ROD ASSEMBLY

43543 TUBE 431 64 SPRING, Compression 4361 1 WASHER, Nylon 4641 9 RING, Retaining 14330 CLEVIS, Adjusting 53283 Piston & Rod Assembly

Qty.

Find ... Go To..

FIG. 5 - MAIN SCRUB BRUSH DRIVE GROUP

Find ... Go To..

FIG. 5 - WIN SCRUB BRUSH GROUP

Ref. TENNANT No. Part No. Descri~tion Qty.

1 261 56 KNOB 2 50457 HANDLE 3 43086 CRANK 4 14331 PIN, Clevis 5 43502 CLEVIS 6 43505 END, Cylinder 7 431 64 SPRING, Compression 8 20021 PIN, Roll 9 431 16 COLLAR 10 43096 CYLINDER, Spring 11 43503 ROD, Brush l i f t 12 1 4 3 0 CLEVIS, Adjustable 13 46646 NUT, Wheel 14 46644 ARM AND PLUG ASSEMBLY, Brush 15 07026 SLEEVE 16 471 78-1 3 PLUGBUTTON 17 46390 BEARING, Ball 18 10464 RING, Retaining, inferml 19 10459 WASHER 20 07037 PLUG, Brush 21 43656 STRl P 22 43653 ABSORBER, Shock 23 43652 ABSORBER, Shock 24 1 1398 PIN, Roll 25 24743 PLUG, Brush drive 26 46605 BLOCK, Bearing 27 46443 BUSHING, Flange 28 24338 STUD, M e e l 29 46642-2 SHIM 30 4349 1 ARM AND SHAFT, Brwh lift 31 43457 ANGLE 32 46480 FITTING, Stmight 33 32377 HOSE 34 53083-8 HOSE 35 4751 8 FITTING, Stmight 36 65084 COUPLING, Hydraulic 37 SK2811 **MOTOR, Drive (Seal K i t i s SK1600) 38 26065 BUSHING 39 33795 *MOTOR, Drive (Seal K i t i s SK1600) 40 77097 *ELBOW 41 33810 *HOSE 42 49263 *TIE, Cable 43 06678 "FITTING, Sfmight 44 33797 *CAP, Dust 45 34414 "COUPLING, Female 46 3441 3 *COUPLING, Male 47 33798 *CAP, Dust 48 478 1 0 *FITTI NG, Reducer 49 47566 *FITTING, Straight 50 55622 *FITTING, Cross 51 55455 *FITTING, Elbow * used on mohines with S/N 9003 and above.

** For machines up to S/N 9003. 1/84 9

Find ... Go To..

Fig. 6 - DETERGENT SOLUTION CONTROL

Find ... Go To..

Fig. 6 - DETERGENT SOLUTION CONTROL


1 9092-1 CLIP, Hold down 2 2 20346 NUT, Casing 4 3 43242 SWIVEL 2 4 54333 C LA MP, Hose 8 5 43372-1 ELBOW ASSEMBLY , R.H. 1 5A 19867 ELBOW ASSEMBLY, L.H. 1 6 43376 ELBOW ASSEMBLY 2 7 43377 HOSE, Side b ~ h 2 8 43379 VALVE 2 9 4359 1 SUPPORT, Spacer, valve 2 10 4341 1 ELBOW ASSEMBLY 1 11 4341 3 HOSE, Tank outlet 2 12 43506 TUBE, Spreader 1 13 43507 HANGER, Spreader tube 2 14 43539 WATER DIVIDER 1 15 43557A CONTROL CABLE 1 16 43558A CONTROL CABLE 1

43560 CLAMP, Cable 1 26683 CLAMP, Cable 2

Find ... Go To..

Fig. 7 - SIDE SCRUB BRUSH 8 SQUEEGEE

Find ... Go To..

Fig. 7 - SlDE SCRUB BRUSH 8 SQUEEGEE

Ref. TENNANT No Part No. Description Qty.

1 04428A SPRING 1 2 43204 CHANNEL 1 3 43667 SIDE BRUSH SQUEEGEE ASSEMBLY 1 4 43290 Pin, clevis ,0.5OUx 1.75" ( 1 2 . 7 ~ 44.5 mm) 1 5 43291 Squsagee back 1 6 43292 Blade, squeegee 1 7 43294 Retainer 1 8 43295 Link 1 9 4331 7 Link 1 10 43500 Chain, side bmh squeegee lift 1 11 43553 Pin, clevis 1 12 43299 PIN 2 13 43497 SUPPORT, Squeegee 1 14 43499 CLIP 1 15 43549 CATCH, Squeegee 1 16 43554 SIDE BRUSH DRIVE ASSEMBLY 1

Find ... Go To..

Detail of

c. HEADLIGHT A N D TAI LLIGHT-LI NTEL MOUNTED ASSEMBLY 54676

Detail of

Assembly

HEADLIGHT AND TAILLIGHT-CAB MOUNTED ASSEMBLY 54677

- Detail of Head Light Assembly

7/83 ~, -- HEADLIGHT A N D TAILLIGHT-HOPPER MOUNTED ASSEMBLY 54679

Find ... Go To..

Ref. No.

Fig. 8 .IGHTS, TAILLIGHTS & SPOTLIGHT KITS

#54679 on HOPPER (Lowdump) #50473 on HOPPER (Hi-dump) #54676 on LI NTE 1 #54677 on CAB

HEADLIGHT AND TAILIGHT KITS

Bumper Mounted: 54679 Lintel Mounted: #54676 Cab Mounted: 54677

TENNANT Part No. Description Qty. Q2-

9384 CLIP, wire 6 141 37 SWITCH 1 15006 CONNECTOR, vinyl sleeve faston 3 22465 SPOTLIGHT 1 32827 BULB 1 5 1572 TAILLIGHT 2 1157-1 2v BULB 2

LENS (signa I-stat 6505) 2 51798 GROMMET, Rubber 2 5 3245 GUARD, Light 2 46108 HEADLIGHT ASSEMBLY 2 10801 HEADLIGHT 1 45110 HEADLIGHT PLATE 2 5 1665 WAP, Headlight 2 46237 GUARD, Hopper wire 1 53245 GUARD, Taillight 2 5441 7 WRING KIT (for hopper mounted) 1 24142 WASHER, Light, adjustable 4 24227 WASHER 2 33545 BRACKET, Headlight 2 5441 5 WIRING KIT (for l intel mounted) 2 24142 WASHER, Light adjusting 4 24298 HEADLIGHT 2 5 1570 BULB, 2 24227 WASHER 2 50448 BRACKET, ~ead l igh t (Standard machine only) 2 50448~ BRACKET, Headlight (Hi-Dump only) 2 524.03 PLATE, Taillight, LPG 2 54420 WIRE HARNESS, Taillight 1 50469 CORD ASSEMBLY 1 46236 CIAMP, Cable, 0.25" dia 1 49287 CLAMP, Cable, 0.75" dia 1 49266 TIE, Cable 1 01574 GROMMET, 0.22" [D 44289

2 GROMMET, 0.38" ID 2

Find ... Go To..

FIG. 9 - REVOLVING LfGHT KITS

Ref. TENNANT No. PortNo. Description Qty.

1 14137 SWITCH 1 07423 FUSE 1

SUPPORT, Flashing 1 light

* LIGHT, Revolving Red 1 BULB 1

46928-1 * LENS, Red 1 46928-2 * LENS, Blue 1 46928-3 * LENS, Amber 1 01 574 RUBBER GROMMET 2

PIATE, Adapter 1 WIRING KIT (Universal 1

kit for all machines) PLATE, Top 1 WIRING KIT, Cab i Includes: wires 14,

42, 8 46 GROMMET 1 BRACKET 2

2 CLAMP, Cable 4

1

Find ... Go To..

FIG. 10 - FlASHlNG LIGHT KITS

No. Part No.

n SMndard achine Ref. TENNANT

On Overhead

*Select color of light

Description Qty.

GROMMET (For LPG Machines) 1 SWITCH, ~ i & t FUSE

TIGHT, Flashing red *LIGHT, Flashing amber "LIGHT, Flashing blue

FLASHER FIASHER BRACKET BU LB

*DOME LENS, Red *DOME LENS, Amber *DOME LENS, Blue

WIRING KIT (Universal) SUPPORT, Flashing light PLATE, Top BRACKET, L CLIP CLAMP, Cable SLEEVE GROMMET WIRING KIT, Cab Includes: wires 7, 14, 42, &43

desired

Find ... Go To..

FIG. 1 l - BRAKE LIGHT KIT 54112

Ref. TENNANT N o . Part No. Description Qty .

1A 47954 SLEEVE 1 28499 CHAIN 2 43672 SPRING, Tension 3 43673 SWITCH 4 44539 BRACKET. Switch .

51798 GROMMET, Rubber 19824 WIRE KIT

Note: This kit adopts opernfing light kit to provide brake light feature.

Find ... Go To..

FIG. 12 - CVERHEAD GUARD - STANDARD MACHINE

Ref. TE N N A N T No . Port No. Description Qty.

50400 OVERHEAD GUARD, Standard machine 1 I 5040 1 GUARD, Top 1 2 50404 LEG, Front, R.H. 1 3 47644 BRACE, Front, R.H. 1 4 50403A LEG, Reor, R.H. 1 5 47645 BRACE, Front, L .H. 1 6 50405 LEG, Front, L .H. 1 7 54522 BRACE, Reor 2 8 50402A LEG, Rear, L .H . 1

Find ... Go To..

FIG. 13- OVERHEAD GUARD for HI-DUMP MACHINE

Ref. TENNANT N o . Part N o . Description Qty.

5041 0 OVERHEAD GUARD, Hi-Dump machine 1 1 50401 GUARD, Overhead 1 2 50404 LEG, Front, R.H. 1 3 62 1 70-4 MOLDING, Channel hose guard 4 4 33576 BRACE, Front 2 5 50405 LEG, Front, L.H. 1 6 50402A LEG, Rear, L. H. 1 7 50403A LEG, Rear, R.H. 1

Find ... Go To..

Find ... Go To..

FIG 14 SWEEPER CAB KIT - $50345

Ref. No.


DOOR, Cab 1 SUPPORT, Rear cab 1 HANDLE, Control 2 RING, Rubber insulating 8 BUSHING, Rubber insulating 8 EXTRUSION, Weatherstripping 1 GLASS, Rear 1 CAB 1 WIPER ASSEMBLY, Windshield 1

MOTOR, Windshield wiper 1 BRACKET, Switch 1 SWITCH, Wiper motor 1 ARM, Wiper blade 1 BLADE, Wiper 1 CLAMP, Cable 3 WIRE KIT, Includes wires 45,46,47,48 1

INSULATION & SEAL KIT, Cab 1 GLASS, Stationary 1 GLASS, Sliding 1 HANDLE ASSEMBLY, Pull & lockset 1 PANEL, Engine cover 1 BRACKET, Support panel 1

SHIELD, Operator SHIELD, Operator, ~o rne r WEATHERSTRIP, Rubber EXTRUSION, Weatherstripping GLASS, Windshield CHANNEL, Rigid CHANNEL, Glassrun, flexible STRIP, Rubber STUD, Snap-on CHANNEL, Rigid, 2.25" (57 mm) CHANNEL, Rigid, 1.06" (27 mm) GROMMET, 0.25" dia GROMMET, 0.38" dia

Find ... Go To..

Find ... Go To..

Fl G. 15 - HI-DUMP MODEL CAB KIT #35504

Ref. No.

TE NNANT Port No. Description Qty.

CAB KIT, Hi-Dump DOOR, Cab SUPPORT, Rear cab HANDLE, Control RING, Rubber BUSHING, Rubber EXTRUSION, Weatherstripping GLASS, Rear CAB ASSEMBLY, Hi-Dump WIPER ASSEMBLY, Windshield

MOTOR, Windshield wiper BRACKET, Switch SWITCH, Wiper motor ARM, Wiper bLode BUD€. Woer ctatii, 3 WIRE KIT, Includes wires: 45, 46, 47, 48

INSULATION 8 SEAL KIT, Cob noise 1 GLASS, Stationary 1 GIASS, Sliding 1 HANDLE ASSEMBLY, Pull & lock set 1 WEATHER STRIP, Rubber 1 CHANNEL, Rigid 1 CHANNEL, Glassrun 1 STRIP, Rubber ,0.25" x 0.50" x 55" (6.4 x 12.7 x 139 mm) 1 PANEL, Engine cover 1 BRACKET, Support panel 1 STUD, Snap on 12 GROMMET, 0.25" hole 1 GROMMET, 0.38" hole 1

23867 EXTRUSION, Weathentripping 23868 GLASS, Windshield 591 18-6 CHANNEL, Rigid, 2.25" (57 mm) 59 1 18-7 CHANNEL, Rigid , 1.06" (27 rnm)

Find ... Go To..

Find ... Go To..

FIG. 16 SCRUBBER CAB KIT #50347

Ref. TENNANT No. Part no.

1 . 241 06 2 50737 3 24464 4 54528 5 54527 6 23934 7 23869 8 53855

23940-2 9 23945 10 23948-1 11 141 37 12 15121 13 2 3947

09384 47999

14 5471 0 15 23870 16 23877 17 15066 18 50826 19 48542-1

14741 21 23942 22 54436 23 5471 1 24 23867 25 23868

23864 23865 23863

Description Qty.

DOOR, Cab SUPPORT, Rear cab HANDLE, Control RING, Rubber insulating BUSHING. Rubber insvlating EXTRUSION, Weatherstripping GLASS, Rear

CAB WPER ASSEMBLY, Windshield

MOTOR, Windshield wiper BRACKET, Switch SWITCH, Windshield wiper motor

ARM, Wiper blode BLADE, Wiper CLAMP, Cable WIRE KIT, Includes wires: 45, 46,

INSULATION KIT, Cab noise GLASS, Stationary GLASS, Sliding HANDLE ASSEMBLY, Pull 8 lock set PANEL, Engine cover BRACKET, Support panel STUD, Smp-on SHIELD, Operofor SHIELD, Operator corner SEAL KIT, Cab EXTRUSION, Weotherstripping GLASS, Windshield CHANNEL, Rigid CHANNEL, Glassrun, flexible STRIP. Rubber

Find ... Go To..

Fia. 17 - SIDE BRUSH DUST CONTROL KIT '54920-1

Find ... Go To..

FIG. 17 S[DE BRUSH DUST CONTROL KIT


IMPELLER HOUSING, Fan RETAINER, Hopper, side skirt SKIRT, Side hopper RETAINER, Hopper, front skirt SKIRT, Front hopper FILTER BOX SEAL, Fire baffle HOUSING, Vacuum intake BAR, Mounting, side BAR, Mounting, front CLAMP, Hose SIDE BRUSH SHROUD ASSEMBLY

SUPPORT, Bumper front SUPPORT, Bumper side SHROUD ASSEMBLY, Side brush BUMPER, Shroud SKIRT, Front

SKIRT, Side RETAINER, Skirt SEAL, Hopper SEAL, Hopper SEAL, Hopper RETAINER, Seal shroud SEAL, Shroud

SEAL MOTOR ASSEMBLY, Shaker RACK, Bag BAG, Filter ARM, Side brush BRACKET, Dust shield support BOLT, Carriage (-50 - 13 x 0.56) NUT, Acorn (-50 - 13) WASHER

NOTE: A l l f i l ter and fan assembly numbers not listed, are standard ports and can be found in parts l i s ts pages.

Find ... Go To..

FIG. 18

VACUUM WAND KIT 54016

Find ... Go To..

PARTS LIST FOR VACUUM WAND KIT 54016 (Standard Machine)

Ref. No. TENNANT Part No. Description

I 2 3 4 5 6 7 8 9

(not shown) (net shown)

DOOR, Fire PIN, Clevis SPRING LATCH PLUG, Expandable CLAMP CHAIN HOSE & CUFF ASSEMBLY WAND CLIP, Holddown SPACER (Hopper) DECAL, Vacuum attachment

PARTS LIST FOR VACUUM WAND KIT 50596 (Hi-Dump Machines) (factory installed only)

TENNANT Port No. Description Qty

DOOR, Fire LEVER, Fire door CATCH, Spring DOOR, Access, hopper SEAL, Hopper access door F1 LTER BOX COVER, Filter bax PIN , Clevis SPRl NG PLUG, Expandable CLAMP CHAl N HOSE & CUFF ASSEMBLY WAND CLIP, Holdown SPACER, Hopper DECAL, Vacuum attachment DECAL, TENNANT oval

Qty.

Find ... Go To..

FARR AIR CLEANER KIT i? 54852

1 531 80-2 AIR FILTER ASSEMBLY, Farr 53179-3 HOUSING, Air cleaner 54028 PANEL, Air pre-cleaner 481 27 ELEMENT, Air cleaner 52033 INDICATOR, Air restriction

2 50827 DOOR, instrument panel 3 54333 CLAMP, Wormdrive 4 50380 HOSE 5 53148-1 MANIFOLD, Vacuum fan air intake 6 49195 FASTENER ASSEMBLY

48088-6 DECAL 62595-17 M O L D I N G

02506-6 CAP, Gas, (Prot ectoseol)

Find ... Go To..

OPERATOR SHIELD KIT #47553

54436 PANEL, Operator corner 23942 SHIELD. O~era tor lea

01 L PRESSURE GAUGE KIT #50307 (In place of warning light)

1 47436 GAUGE, Oil pressure 1 2 53126 HOSE 1 3 17414 CONNECTOR I

47178-4 PLUG BUTTON, 0.50 dia . 1

ELECTRIC FUEL PUMP KIT #50323-1

1 50337 BRACKET, Fuel pump mounting 1 2 50325 TUBE 1 3 22383 CONNECTOR 2 4 54230 PUMP, Fuel 1

1 5 56724 TUBE 1 6 51805 SENDING UNIT, Oil pressure 1

Existing Ford 7 17414 CONNECTOR I Oil pressure switch 24929 TEE 1

0 54875A WIRE HARNESS 1 47454 DECAL, UL type gas 1 50567 DIODE ASSEMBLY (LPG) 1

7/83 32

Find ... Go To..

4671 2 PANEL LIGHT KIT 1 47768 LAMP & WIRE ASSEMBLY 1 141 37 SWITCH 1 47769 WlRE ASSEMBLY 1

53195 FUEL GAUGE KIT 1 I 1 47472 GAUGE, Fuel level 1

2 47473 SENDING UNIT , Fuel level 1 74131 GASKET 1 MD204 WlRlNG DIAGRAM 1 14215 FUSE I

24147 HOPPER DOLLY ASSEMBLY 1 1 241 45 CART 1 2 241 49 SOCKET 4

24259A CASTER, Swivel 4

45938 FIRE EXTtNGUISHER KIT 1 2531 2 FIRE EXTINGUISHER 1

- -

Find ... Go To..

ACCESSORIES NOT ILLUSTRATED


53848 TIRE CHAIN 1

43941 GAS SPOUT EXTENSION KIT 1 43940 EXTENSION, Spout 1

HEAVY DUTY FILTER BOX KIT FILTER BOX ASSEMBLY LEAD, Shaker motor

REAR TlRE & WHEEL ASSEMBLY, "BEARCAT" 1 RIM ASSEMBLY 1 TIRE, Solid 1 DECAL, Caution 1

FRONT TlRE & WHEEL ASSEMBLY,SOLID TIRE2 RIM, M e e l I TIRE, Solid smooth 1

HI-SPEED PROPELLING KIT MOTOR (Char-Lynn) SCREW CONNECTOR HOSE

BATTERY HOLD-DOWN KIT 1 BRACKET, Batte hold down T~ 1 ROD, k t t e r y h o d down I

TIRE 8 WHEEL ASSEMBLY, Foam-filled TlRE TUBE RIM ASSEMBLY CAP, Valve stem

53819-2 FLAP

TIRE & WHEEL ASSEMBLY, SteeIgwrd 1 TIRE, TUBE & FLAP ASSEMBLY 1 CAP; Valve stem 1

TIRE a WHEEL ASSEMBLY, 4 I TIRE 1 TUBE 1 RIM ASSEMBLY T CAP, Valve stem 1

61034-1 BATTERY, 12 V 1

39550 AIR BYPASS KIT 1 3955 1 STIFFENER, Door seal 1 39554 DOOR ASSEMBLY 1 39559 ARM, Control 1 56202 SCOOP, Air 1

7/83 09092-1 CLAMP - . 1 ,a

Find ... Go To..

POWER SWEEPER

LPG SYSTEM PARTS LISTS

LP Tank and Engine Cover - - - - - -1

LPSystemParfs - - - - - - - - - - - 2 - 3

LP Carburetor - - - - - - - - - - .. - 4 - 5

Find ... Go To..

Find ... Go To..

01906

LP COMPONENTS - TANK AND COVER GROUP

Ref. I E N N A N T No, Part No. Description Qty.

1 3231 8 STRAP ASSEMBLY, Left Hand 1 2 24928 TANK, 1P (liquid withdrawal) 1 3 3231 7 STRAP ASSEMBLY, Right Hand 1 4 32319 LOCATOR, Tank I 5 53400-1 LATCH 2 6 53400-4 NUT, Adiustable 2 7 26496 COUPLING, LP 1 8 22308-3 HOSE 1 9 24049 PLATE, Data, LP 1 10 54216 TEE (Includes 3/4 flat washer, 3/4 star washer 1

and 314 nut) 11 24047 VALVE, Pressure relief, LP 1 12 54937-2 COVFR, Engine 1

50306 PAWL, Latch 1 49302-1 FASTENER, Engine cover 1

7/83 1

Find ... Go To..

Find ... Go To..

LP COMPONENTS 01907 Ref. No.

16 17 18 19 20 21 22 23 24 25 26 27 28

29 30 31 33 34

35 36 37 38

39 (not shown)

40

TENNANT Port No. Description Qiy.

CLAMP 3 HOSE, Air Intake (New one-piece molded type)l NOTE: Previous hose (#50331), Spring (X50349) and Adapter (#54149) (replaced by SK 1844) PLUG, Pipe, 1/8" 1 CLAMP 1 CARBURETOR, LP 1 HOSE 1 CLAMP 4 ELBOW, 45' 1 ELBOW 2 TUBE, LP 1 STUD 2 GASKET, Carburetor 2 HOSE, Rubber, governor t o distributor 1

(Furnished w i th engine) CONNECTOR 1 GOVERNOR 1 SWITCH, Oil pressure 1 ELBOW 3 SWITCH, Oil pressure (Ford) 1 BALLJOINT 1 ROD, Throttle 1 BALLJOINT 1 PIVOT, Arm 1 CLAMP, Stop, throttle rod 1 LEVER, Throttle 1 SPRING, Throttle return 1 CONVERTER, LP 1

REPAIR KI T, Converter 1 ELBOW 2 HOSE, LP 2 ELBOW 1 CONNECTOR 1 FUEL FILTER LOCK (repair kit i s SK1444) 1 . . DIODE ASSEMBLY BRACKET HOSE WIRE HARNESS, LP FITTING, Pipe TEE

**ENGINE, Basic, LP COVER, (fuel pump opening) GASKET, (Fuel pump opening)

""Machines with serial number up to and including 7414 used engine 5491 1-1. To replace 5491 1-1, order SK2492. The basic engine 32512 does not include

7/83 alternator, carburetor, voltage regulator, V-belt, fan, pulleys, and coi l .

3

Find ... Go To..

LPG CARBURETOR 854929

Find ... Go To..

PARTS H S T FOR LPG CARBURETOR t54929

Ref. lmpco No. Part No. Description Qtv.

1 51 -3 SCREW 4 2 C1-17 COVER 1 3 52-1 3 SPRING. Air Valve 1 4 51 -22 SCREW 4 5 PZ-22 PLATE, Back-up 1 6 D l -17 DIAPHRAGM 1 7 R1-19 RING, Air valve 1 8 BVi -14 AIR-GAS VALVE ASSEMBLY 1 9 AVl-1 4 VALVE & DIAPHRAGM ASSEMBLY 1 10 ABl-8-. . . BODY ASSEMBLY (Specify for 2.06" air horn) 1 11 52-6 SPRING, Idle screw 1 12 S1-11 SCREW, Idle 1 13 GI-11 GASKET, Throat to body 1 14 51 -19 SCREW 4 15 P3-3 PLUG, Pipe 1 16 T 2-3 THROAT 1 17 PI-5 PIN, Throttle stop 2 18 55-... SHAFT, Throttle (specify shaft dia .) 1 19 F2-4 FLY, (for 1 .SOa thrwt) 1 20 GI-18 GASKET 1

NOTE: Ref. N d r 1 hnr 15 are included in MIXER ASSEMBLY ~CA-IWM-~. THROTTLE BODY ASSEMBLY # i s A.T2-3.

Find ... Go To..

Find ... Go To..

CONTENTS page

Fig. 1, 2, 8 3 VICKERS TANDEM PUMP 2-5 Fig. 4 ALTERNATE MOTORS (Char-Lynn) 6-7 Fig. 5 MAIN BRUSH MOTOR 8 Fig. 6 M A I N BRUSH MOTOR (Ross Obsolete) 9 Fig. 7 SIDE BRUSH MOTOR (Ross) 10 Fig. 8 M A I N SCRUB BRUSH MOTOR 11 Fig. 9 WHEEL DRIVE MOTOR 12-13

NOTE

The moton, pumps, and valves covered here have been rncdified far use on TENNANT Company rnochines. Repair parts should be ordered only from the parts lists provided i n this section.

Production requirements may occasionally dictate that hydraulic components made by other manufacturers must be used. Please check the component For manufacturer's name and model number before ordering parts or seal kits.

Find ... Go To..

Find ... Go To..

ORDERING REPAIR PARTS FOR GASOLINE ENGINETENNANTB PART NO. 76874A

FOR LPG ENGINE TENNANT' PART NO. 78081 A

The componenls usec in this machine have been care- If parts received are suspected to be incorrect or fully selected for performance and safety. Use only defective, please write, wire, or phone the parts supplier Tennant Camnanv suoolied or eauivalent oarts. from whom you ordered the part. They will give authori- .~~ . ~ ~ - 7 - - - ~~ - ~7~~ ~

zation for return andlor handle replacemeit shipments To receive prompt service in filling your parts orders, when required, please direct all parts orders with Tennant Commny part numbers to the Tennant Company, and all parts orders with vendor part numbers to the local suDplier of the respective vendor.

To avoid errors or delays in filling your parts orders, please furnish all of the following information.

1. Refer to Tennant Company data plate. Always specify the machine model number and the machine serial number shown on the machine data plate.

2. Refer to the vendor part data plate. Always specity the model number and serial number shown on the data plate.

3. Give the part number,description, and the auanti- ty needed of each item on the order. Do not order by reference number or the figure number of the illustrated parts.


5. If the old part cannot be identified, send it to us with thequantity needed specified on theorder.

6. State definite shipping instructions to include the shipping address and/or the billing address. if there is a difference. Any claim for loss or damage to a shipment in transit should be filed promptly against the transportation company making the delivery. Shipments will be complete unless the packing list ororder acknowledgement indicate items back ordered.

POWER SWEEPER - 165HU114(7-831 LlTiiOIN U.S.A.

51 (INTERNATIONAL SYSTEM) UNITS OFMEASURE


BOLT AND CAP SCREW STRENGTH IDENTIFICATION

Bolts and cap screws required to have high-strength qualities equivalent to SAE Grade 8 are identified throughout this catalog by the description GR 8. Unless identified by this description, all standard boltsand cap screws are SAE Grade 5.

Find ... Go To..

Find ... Go To..

FIG. 1 - VICKERS TANDEM PUMP PARTS LIST

Ref. No.

TENNANT Company Part Number 47925 (Standard machine) TENNANT Company Part Number 47861 (Hi-Dump machine)

VICKERS Part No. Description Qty.

001 278 SCREW 4 039640 PIN 2 093509 RING, Snap 1 98653 RING, Refainer 1 119982 RING, Reiainer I 120428 RING, Retainer 1 1704 BEAR1 N G 1 *I 541 30 0 - R I N G 1 *I54131 0 - R I N G 1 181 792 PLUG 1 187087 PLUG 1

* 159822 0 - R I N G 1 *I59823 0 - R I NG 2 239077 PLATE, Swash 1 241 954 WASHER, Thrust 1 245223 WASHER 1 247294 SPRING 1 24881 1 PIN, Spring 3 260860 CYLINDER, Block 1 941 887 PISTON KIT, (9 1

*q63585 SEAL, Shaft 1 274382 RETAINER, Shaft seal 1 275961 PLATE, Shoe 1 317162 GASKET 1

BODY, Vane pump RING -. . ..

326805 BEARING, Ball 325689 YOKE

*"343573 SEAL, Oil, shaft

351 247 ROTOR, Vane pum P 1 423324 WASHER, Spherics 1 374343 PRESSURE PLATE SUB-ASSEMBLY 1 372865 COVER, Vane pump 1 397742 SHAFT, Vane pump 1 39021 8 R i NG, Retainer 1 389354 COUPLING 1 389355 RACE, Inner 1 390219 BEAR1 NG, Needle 1 392305 HOUSING 1 400395 PLATE, Valve 1 39i737 SHAFT, Drive, Piston pump 1 923500 VANE KIT, (12 vanes) 1

* lnciuded i n Overhaul Seal Ki t SK 1344 ** Included in Shaft Seal Ki t SK 1345

(See Following pages for additional park) 3

Find ... Go To..

FIG. 2 - VICKERS TANDEM PUMPS N O . 47925 & 47861

Ref. VICKERS NO. Part No. Description Qiy.

1 001 306 SCREW 2 2 09966 KEY, Lever 2 3 012016 BEARING, Needle 2 4 .*I54014 0-RI N G 4 5 474963 KEY, Pintle 2 6 347573 PLATE, Pintle cwer 2 8 424520 YOKE, Pintle, Long 2 9 318399 RELlEF VALVE , 4500 psi (31,027 kPa) for 47861 pump 2 9 339490 RELIEF VALVE , 3000 psi (20,685 kPo) for 47925 pump 2 10 307354 PLUG 2 1 1 *I54129 O-RING 2

* Induded in Overhaul Sml Kif SK 1344

Find ... Go To..

FIG. 3 - VICKERS TANDEM PUMPS NO. 47925 & 47861

Ref. VICKERS No. Parf No. Description Qty.

FlTTl NG 0 - R I NG 0 - R I NG SPRl NG SHIPPING PLUG SHIPPING PLUG PLUG POPPET-CHECK VALVE RETAl NER, Spring

* Included in Overhaul Seal K i t SK 1344

Find ... Go To..

FIG. 4 EXPLODED VIEW OF CHAR-LYNN HYDRAULIC MOTORS (-007SERIES) USED FOR SIDE BRUSH, M A l N BRUSH AND M A l N SCRUB BRUSH.

(Reference numbers refer to Parts List)

.Model Number

Serial Number

Ftuid Power F:'I.IY-

Find ... Go To..

Ref. No.

1 2 3 4

5 6 7 8 9 10 11 12 13 14

15 16 17 18

* Indicates parts of Seal K i t No. SK1600, which includes instructions.

FIG. 4 - HYDRAULIC MOTORS

PARTS LISTS FOR CHAR-LYNN HYDRAULIC MOTORS (-007 Series) USED O N SIDE BRUSH, MAIN BRUSH & MAIN SCRUB BRUSH

PI1 component parts numbers listed above are Char-Lynn numbers.

Before ordering ports, check motor nameplate to determine which motor model was used on your machine. Remember that Ross and Char-Lynn hydraulic motors con be used as olterncrtes.

Side Brush Char-Lynn

TENNANT #

I design series 007

47650-1 2 Description

5777 SCREW, Cap * SEAL, Dust, shaft

7464 FLANGE, Mounting I SEAL, Shaft (alternate sea

& back-up ring may be used, however, for replacement order #9057-1)

+ O-RING 7462 RACE, Thrust bearing 75 37 BEARING, Thrust, needle 7360-1 3 SHAFT, Output 7359 - 1 HOUSING 9029-1 NAMEPLATE 61 6 DRIVE 7358 PLATE, Spacer

s O-RING 7357-6 GEROTOR ASSEMBLY

(includes ring & star) 6901-5 SPACER 746 1 CAP, End 6049 WASHER, Seal 5389-6 SCREW, Cop

Obsolete

I Obsolete

Main Blush Main Scrub Brush Char-Lynn

TENNANT design series 007

47650

5777 *

7464 3

I * 7462 7537 7360-7 7359-3 9029-1 602 7358

* 7357-2

none 7461 6049 5389-2

1

Char-Lynn

TENNANT # design series 007

476504

5777 *

7620 *

.x

7462 7537 7360-5 7359-1 9029-1 602 7358

+ 7357-2

none 7461 6049 5389-2

Qty.

4 1 1

11

1 1 1 1 1 1 1 1 3

1 1 1 7 7

Find ... Go To..

FIG. 5 - M A I N BRUSH MOTOR BREAKDOWN 9x556


* 34423 MOTOR, Hydraulic 1 SKI600 SEAL KIT 2 34174 F I A NGE, Mounting 3 341 75 SHAFT ASSEMBLY, Outpuf 4 341 76 DRIVE 5 341 77 GEROTOR SET

* Used on machines with serial number from 9003 and above.

Find ... Go To..

Ref. No.

FIG.^ - MAIN BRUSH MOTOR 47514 (OBSOLETE)

ROSS Part No. Description

MAC012007 HOUSING 065503 BEAR I NG, Needle 401 369 RING, Retaining * *SPACER

I: *SEAL, Shaft 4001 08 WASHER, Thrust 066980 BEARING, Thrust 09 1430 SHAFT, Coupling MAC063000Al DRlVE LINK ASSEMBLY 477255 SPACER MAC067000 ROTOR SET MAC015000 MANIFOLD MAC014000Al COMMUTATOR ASSEMBLY

* *O-RI NC 099061 RETAINER, Seal 028395 WASHER 402364X T END COVER ASSEMBLY 021 306 SCREW 032200-1 0 0 - R I NG, Port

Qty.

* Included in Seal K i t SK1694(instructions for seal replacement and repair included).

Char-Lynn motors may be used as alternates -- check your motor before ordering repair parts.

Find ... Go To..

FIG. 7 - SIDE BRUSH MOTOR 47542

Ref. ROSS No. Part Number Descripfion Qty.

1 MAC012008 HOUSING 2 065503 BEARING, Needle 3 401 369 RING, Retaining 4 * SPACER . .

SEAL, Shaft WASHER, Thrust BEARING, Thrust SHAFT, coupling DRIVE LINK ASSEMBLY SPACER ROTOR SET MANIFOLD COMMUTATOR ASSEMBLY 0 - R I NG RETAINER, Seal WASHER END COVER ASSEMBLY SCREW

* Included in Seal K i t SKI694 (instrwtions for seal replacement and repair included).

Char-Lynn motors may be used as alternates - check your motor before ordering repair parts.

Find ... Go To..

Is- FIG. 8 - MAf N SCRUB BRUSH BREAKDOWN

Ref. Char-Lynn No. Port No. Description Qty.

* 33795 MOTOR, Hydmulic, Scrub 1 ** SK1600 SEAL KIT 2 7620 FLANGE, Mounting 3 7462 RACE, Thrust bearing 4 7537 BEAR1 NG, Thrust, needle 5 7360-5 SHAFT, Output 6 602 DRIVE 7 7357-2 GEROTOR ASSEMBLY

* Used on mochines with serial number from 9003 and above.

** Tennant Company part number

Find ... Go To..

Find ... Go To..

PARTS LIST FOR FIG. 9

Fig. 6 Ref. No.

(not shown) 27

WHEEL DRIVE MOTOR - STANDARD MACHINES '53032 WHEEL DRIVE MCTCR - HI-DUMP MACHINES "3041

Motor Motor 53032 37041 Part No. Part No.

067031 067031 MAB243001 MAE243000 477237 477259 MAB24700043 MAE247000 NSS NSS NSS . NSS NSS NSS 477238 477260 MABO15001 MAE015000 MAB018M)OSI MABOlaOOOSl

NSS NSS G32435 032435 NSS NSS 099024 099066 MAB016000-A1 MAE016000-A1 02 1272 021 273 039027 039027 0251 13 0251 13 SKI 140A SKI 140A

Description

SEAL, Dirt RING, Retaining SPACER, Seal WASHER, Backup SEAL, Shaft HOUSING ASSY. (includes

items 8, 4, 10, and 12 O-RING, Body WASHER, Thrust BEAR1 NG, Thrust BEARING, Needle SHAFT BEARING, Needle BEARING, Thrusf LINK, Drive PLATE. Wear ROTOR ASSY., Includes:

ROTOR - - -

VANE STATOR & RING ASSY.

PLATE, Manifold MANIFOLD COMMUTATOR ASSY.

(includes 19 B 21) COMMUTATOR SEAL, Commutator RING, Comrnutacrtor SLEEVE END COVER ASSY. SCREW KEY, Shaft NUT, Slotted SEAL KIT (includes items 1,

2,3,4,5,7, & 20) O-RING, Port (not part of

motor)

NOTE Al l reference part nurnben are Ross part numbers. Items marked "NSS" are not available separately, only in assemblies. Motor seal k i t includes all seals and repair instructions.

Find ... Go To..

Find ... Go To..

CONTENTS Page

Ordering Repair Pans 1 Fig. 1 - Cylinder Block and Head Group ................ 2 Fig. 2 - Crankshaft Parts Group 4 Fig. 3 -Valves. Push Rods, and Rmker Arm

-Cover Group .................................................. 6 Fig. 4 - Camshaft. Gear. and Bearings Group ....... 8 Fig. 5 - Piston and Connecting Rod Group ............ 9 Fig. 6 - Oil Pump. Oil Pan, and Crankcase Vent

- Group ... 10 Fig. 7 - Water Pump. Thermostat, and Fan Blade

- ~ r o u p ..................................................... $ 2 Fig. 8 - Intake. Exhaust Manifold, and

- Carburetor Group ...................................... 13 Fig. 9 - Fuel Fitter and Fuel Pump Group ............. 14 Fig. 10 - Ignition Coil Distributor. and Spark

- Plugs Group 15 Fig. 11 - Alternator Gmup ......................................... 16 Fig. 12 - Starter Motor 17 Fig. 13 - Engine Gasket Kits Group ........................ 18

Find ... Go To..

Find ... Go To..

ORDERING REPAIR PARTS FOR GASOLINE ENGINE TENNANT" PART NO. 76874A

FOR LPG ENGINE TENNANP PART NO. 78081A

The components used in this machine have been care- fully selected for performance and safety. Use only TennantCompany suppliedorequivalent parts.

To receive prompt service in filling your parts orders. please direct all parts orders with Tennant Company part numbers to the Tennant Company, and all parts orders with vendor part numbers to the local supplier of the respective vendor.

To avoid errors or delays in filling your parts orders. pleasefurnishall of thefoflowing information.

1 Refer to Tennant Company data plate. Always specify the machine &el number and the machine serial number shown on the machine data plate.

If parts received are suspected to be incorrect or defective, please write, wire, or phone the parts supplier from whom you ordered the part. They will give authorization fcr return and/or handle replacement shipments when required.

SI (INTERNATIONAL SYSTEM) UNITS OF MEASURE


BOLT AND CAP SCREW STRENGTH IDENTIFICATION

Bolts and cap screws required to have high-strength qualities equivalent to SAE Grade B are identified thmuahout this cataloa bv the descriotion GR 8. Unless identified by this description, all standard bolts and screws are SAE Grade 5.

2. Refer to the vendor part data plate. Always specity the model number and serial number shown on the data plate.

3. Give the part number, description, and the quantity needed of each item on the order. Do not order by reference number or the figure numbsr of the illustrated parts.


5. If the old part cannot be identified, send i t to us with the quantity needed specified on the order.

6. State definite shipping instructions to include the shipping address andlor the billing address if there is a difference. Any claim for loss or damage to a shipment in transit should be filed promptly against the transportation company making the delivery. Shipments will be complete unless the packing list or order acknowledgement indicate items back ordered.

Find ... Go To..

FIG. 1 - CYLINDER BLOCK AND HEAD GROUP

Find ... Go To..

FIG. 1 - CYLINDER BLOCK AND HEAD GROUP

TENNANTB FORD ENGINE KEY PARTNO. PART NUMBER SERIAL NUMBER DESCRIPTION

1 71 1 M-6010-BA ( ) BLOCK. Cylinder 751M-6011-ACA ( - 1 BLOCK, Cylinder with ptstons, etc.

2 37351 01 RY-9278-A ( SWITCH. Oil pressure 3 DORY-6055-A ( LINER, Cylinder block, standard

DORY-6055.6 ( ) LINER, Cylinder block. 0.020" OIS 4 731 M-6059-3A ( ) FRONTCOVER 5 37333 D l FZ-6020-6 ( 1 GASKET, Front cover 6 37342 D l FZ-6700-8 ( SEAL. Front cover oil 7 54911-2 D6JL-6A018-A ( ) HEAD, Cylinder 8 54911-23 DORY8051 -8 ( - ) GASKET. Cylinder head 9 DlFZ-6065-B ( . I BOLT. Cylinder head

D l R b 0 6 5 C ( - ) BOLT, Cylinder head 10 78005-2 D t FZ-10684-8 ( - 1 SENDER, Water temperature

54911-16 70HM-6397-AA ( - 1 PIN. Dowel

QTY. -

1 1 1 4 4 1 1 1 1 1 5 2 1 1

Find ... Go To..

~micedo& in Block Asaembly

FIG. 2 -CRANKSHAFT GROUP

Find ... Go To..

KEY

FIG. 2 - CRANKSHAFT GROUP

TENNANT" FORD ENGINE PART NO. PART NUMBER SERIAL NUMBER DESCRIPTION

D8RZ-6303-A ( I CRANKSHA- 37321 DORY-6306-A 1 I SPROCKET

01 FZ-631 O-A ( I SLINGER DSJL-6A3I 2-A ( I PULLEY. Double sheave

3731 2 DORY-6B316-A ( I KEY 37353 D2FZ-6333-L ( I BEARING, Standard O.D. and

standard 1.0. red 37352 D2FZ-6333-0 ( - I BEARING. Standard 0.0. and

standard 1.0. blue 38073 D2FZ-6333-E ( I BEARING. Standard O.D. and

0.010" undersize I.D. D2FZ-6333-F ( - 1 BEARING. Standard O.D. and

0.020" undersize I.D. D2Ft-6333-0 ( I BEARING, Standard O.D. and

0.030" undersize 1.0. BEARING. 0.01 5" oversize O.D. and standard 1.0.

BEARING. 0.015 oversize O.D. and 0.010 undersize I.D.

BEARING, 0.01 5 oversize 0.0. and 0.020 undersize 1.0.

BEARING. 0.01 5" oversize 0.D. and 0.030" undersize I.D.

BOLT, Main bearing cap RETAINER GASKET WASHER. Main bearing, standard. 2.938" O.D.

WASHER, Main bearing, 0.025" oversize

WASHER, Main bearing, 0.005" oversize

WASHER. Main bearing. 0.0075" oversize .

WASHER, Main bearing, 0.010 oversize

SEAL, Front cover SEAL, Crankshaft rear PLATE, Rear engine FLYWHEEL GEAR, Flywheel ring DOWEL. Cylinder block to flywheel DOWEL. Flywheel to clutch pressure plate

As Req.

As Req.

As Req.

As Req.

As Req.

AS Req.

As Req.

AS Req.

As Req.

As Req.

Find ... Go To..

UG. 3 - VALVES, PUSH RODS, AND ROCKER ARM COVER GROUP

Find ... Go To..

KEY

1

TENNANT" PART NO.

FIG. 3 - VALVES, Pusn RODS, AND ROCKER ARM COVER GROUP

FORD ENGINE PART NUMBER SERIAL NUMBER DESCRIPTION

D 1 FZ-6500-A ( ) TAPPET. Standard 0.51 5" stem O.D. D l R-6500-6 1 TAPPET. 0.004" oversize 71 1 M-6507-KA ( ) VALVE. Standard. 3 groove, intake 731 M-6507-AA ( ) VALVE, Standard, 1 groove. intake 71 1 M-6507-LA ( ) VALVE. 0.003 oversize, 3 groove.

intake 71 1 M-6507-MA ( ) VALVE. 0.01 5 oversize. 3 groove.

intake DH8RZ-6505-A I ) VALVE. Standard. 3 groove, exhaust 731 M-6505-AA ( ) VALVE. Standard, 1 groove, exhaust 71 1 M-6505-JA 1 ) VALVE. 0.01 5 oversize. 3 groove.

exhaust DORY-6510-A 1 ) BUSHING, Valve guide, intake. .

1.825". plain DORY-6510-C ( - 1 BUSHING, Valve guide. intake.

1.825". shouLdered DORY-6510-6

DORY-651 O-D

BUSHING. Valve guide, exhaust, 2.075, plain

BUSHING, Valve guide, exhaust, 2.075", shouldered

SPRING RETAINER KEY, 3 groove BOLT WASHER SUPPORT SCREW NUT SHAFT PIN, Cotter, 1" long PLUG ARM. R.H. ARM, L.H. ROD, Push SEAL SPRING, Valve rocker to shaft WASHER. Flat type WASHER. Spring type COVER GASKET CAP

QTY.

8 AS Req.

4 4

As Req.

As Req.

4 4

As Req.

As Req.

As Req.

As Req.

As Req.

8 8 16 4 4 4 8 8 1 2 2 4 4 8 8 3 4 2 1 1 1

Find ... Go To..

KEY -

FIG. 4 - CAMSHAFI, GEAR, AND BEARINGS GROUP

TENNANP FORD PART NO. PART NUMBER

71 1F-6250dC DORY-6253-A DORY-8255-A

37315 DORY-6256-A DORY-6258-A

37316 DORY-6261 -A

ENGINE SERIAL NUMBER DESCRIPTION

( 1 CAMSHAFT ( I DOWEL ( 1 RETAINER ( ) SPROCKET ( RETAINER

) BEARING, Front, standard I.D, and 0.0.

3731 7 DORY-6261-5 ( - 1 BEARING. Front, standard I.D. and 0.020 0,s. - O.D.

37306 DORY-6262-A ( - 1 BEARING, Center, standard I.D. and O.D.

38242 DORY-6262-6 ( ) BEARING, Center. standard 1.0. and 0.020 O.S. - 0.0.

37306 DORY-8262-A ) BEARING. Rear. standard I.D. and 0.0.

38242 DORY-6262-B ( ) BEARING, Rear, standard I.D. and 0.020" 0,s. - 0.0.

37307 DORY-6268-A I CHAIN DORY-6269-A I - I PLATE

37337 01 FZ-6284-A ( I TENSIONER 37338 D l FZ-62B5-A I I ARM 37694 Dl FZ-6286-A ( I PIN

OTY.

8

Find ... Go To..

I-' RG. 5 - PISTON AND CONNECTlNG ROD GROUP w7u

TEMNANTs FORD ENGINE KEY PARTNO. PART NUMBER SERIAL NUMBER DESCRIPTION QTY.

PISTON, Standard PISTON. 0.030 0/S

PIN, Standard PIN, 0.002" Undersize RETAINER. Pin RING SET. Piston. standard RING. Piston. 0.030" O/S

ROD ASSEMBLY BUSHING BEARING. Standard BEARING. 0.001" undersize BEARING, 0.002 undersize BEARING, 0.010" undersize BEARING, 0.020" undersize BEARING. 0.030 undersize BEARING. 0.040" undersize BOLT. 0.38" - 24 x 1.718 DOWEL. 0.31" dia x 0.375"

4 As Req.

4 AS Req.

8 1

AS Req. 4 4 8

AS Rw. As Req. As Req. AS Req. As Rea. As Req.

8 8

Find ... Go To..

FIG. 6 -OIL PUMP, OIL PAN, AND CRANKCASE VENT GROUP

Find ... Go To..

FIG. 6 - 01L PUMP, OIL PAN, AND CRANKCASE VENT GROUP m7si

TENNANTB FORD ENGINE KEY PART NO. PART NUMBER SERIAL NUMBER DESCRIPTION QTY.

OIL PUMP 1 ROTOR AND SHAFT 1 O-RING 1 TUBE, Oil pickup 1 GEAR 1 PIN 1 TUBE, Oil return 1 GASKET 1 ADAPTOR. Crankcase ventilation 1 VALVE. Crankcase ventilation. PCV 1 HOSE. PCV 1 SPRING 1 PLUNGER 1 OIL FILTER 1 OIL PAN 1 PLUG, Oil drain 1 GASKET, Oil drain 1 INDICATOR. Oil level 1 TUBE. Oil level indicator 1 O-RING 1 GASKET, Oil pan 1 SEPARATOR 1 EXTENSION. Oil levet indicator 1 INSERT. Oil filter rnountlng bolt 1 GROMMET. PCV valve 1

Find ... Go To..

KEY

1 2 3 4 5 6 7 8 9

10 11 1 2 1 3 14 15 16

17

FIG. 7 - WATER PUMP, THERMOSTAT, AND FAN BLADE GROUP


37345 DORY-8501-A ( . I WATER PUMP 37325 DORY-8507-A [ - 1 GASKET

01 FZ-8564-A t - ) SEAL Dl--8512-8 I IMPELLER DORY-851 7-A ( ) SEAT D4RY-8530-A ( ) SHAFT AND BEARING DORY-8K537-A ( ) RETAINER DORY -8550-A ( - 1 SLINGER DORY-8553-A ( - 1 HUB

54971-10 D l FZ-85096 ( - 1 PULLEY 37327 D4PZ-8575-A ( - ) THERMOSTAT 5491 1-25 D l FZ-82556 ) GASKET 37346 D l FZ-8592-8 ( - ELBOW

D9JL-8600-A ( . FAN. 6 blade D7PZ-8620-C ( ) BELT 241 589 ( ) BOLT. M8 x 20mm 8A-8115 ( ) DRAIN COCK D9JL-8546A ( - ) SPACER. Fan

QTY.

Find ... Go To..

flG. 8 - INTAKE, EXHAUST MANIFOLD, AND CARBURETOR GROUP 01 31 s

TENNANTD FORD ENGINE KEY PART NO. PART NUMBER SERIAL NUMBER DESCRIPTION QTY.

1 761 F-9425-AA ( . MANIFOLD. Intake 1 2 32838 781 F9430AA ( - ) MANIFOLD. Exhaust 1 3 5491 7 -22 ( - 1 GASKET. Intake manifold 1 4 5491 1-20 DORY-9448A ( 1 GASKET, Exhaust manifold, inner 1 5 5491 1-21 DORY-94486 ( . ) GASKET. Exhaust manifold, outer 2

13

Find ... Go To..

FIG. 9 - FUEL FILTER AND WEL PUMP GROUP ~ 7 4 0

TENNANT FORD ENGINE KEY PART NO. PART NUMBER SERIAL NUMBER DESCRIPTION OTY.

1 CZRZ-97 55-A ( ) FUEL FILTER KIT 1 2 D9JL-9180-B I 1 BRACKET 1 3 EOJL-9261 AA ( 1 HOSE. Filter to carburetor 1 4 380882-S32 ( 1 HOSE, Clamp 3 5 5491 2-2 DORY-9350-0 ( ) FUEL PUMP ASSEMBLY 1 6 5491 1-29 DORY-941 7-A ( I GASKET 1

Find ... Go To..

KEY - 1 2 3 4 5 5 6 6 7 7 8 8 9 9

10

w

FIG. 10 - IGNITION COLL, DISTRIBUTOR, AND SPARK PLUGS GROUP


DSTE-I 2029-A0 ( 1 COIL SKI945 ( - ) STRAP

DSJ6-12250-A ( - I RESISTOR B7P-14497-A ( WIRE, Resistor to coil 7lBB-12100-BHA ( - I D~STRIBUTOR, ~ o s c h

37440 71 00-1210WANB ( ) DISTRIBUTOR. tucas 58507 DlfZ-12106-A ( 1 CAP. Boscn 3731 1 DORY-12106-A ( 1 CAP, Lucas 58506 778F-12177-AA ( I POINTS, Bosch 37356 DP12 ( 1 POINTS SET, Lucas 58508 D l FZ-12200-A ( ) ROTOR, Bosch 3731 0 DORY-12200-A ( 1 ROTOR, Lucas 58509 831 F-12300-AA ( ) CONDENSER, Bosch 37408 DORY-12300 ( I CONDENSER, Lucas 37328 Dl FZ-12259A ( ) WIRE. No. 2 37328 D l FZ-12259A ( ) WIRE, NO. 3 37328 D l FZ-12259A ( ) WIRE. NO. 1 37328 D l R-12259A ( i WIRE. No. 4

D4FZ-I 2298-A ( 1 WIRE. High tension 45770-8 ( 1 SPARK PLUGS

IS

QTY. - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4

Find ... Go To..

FIG. 11 - ALTERNATOR GROUP ~ 1 0 7

TENNANTm FORD ENGINE KEY PART NO. PART NUMBER SERtAL NUMBER DESCRIPTION QTY.

DBZF-I 0300-AA I 1 ALTERNATOR ASSEMBLY 1 D9PZ-10316-A ( 1 REGULATOR. 2.60" high 1 OBVZ-10316-A ( 1 REGULATOR, 1.70" high 1 D l R-10A313-C I 1 BRACKET. Mounting I C9JJ-10145-A ( I ARM, Adjusting, with 2 bolt holes 1

Find ... Go To..

no. t 2 - STARTER MOTOR m7ll

TENNANT* FORD ENGINE KEY PART NO. PART NUMBER SERIAL NUMBER DESCRIPTION ' QTY.

STARTER MOTOR CONSISTS OF: ARMATURE, No. 25270 ARMATURE. No. 121 1206 BRUSH SET, No. 25270 BRUSH SET. No. 121 1206 DRIVE ASSEMBLY. No. 121 1206 SOLENOID, No. 25270 SOLENOID, No. 121 1206

Find ... Go To..

KEY -

FIG. 13 - ENGlNE GASKEt KITS GROUP

TENNANT" FORD ENGINE PART NO. PART NUMBER SERIAL NUMBER DESCRIPTION QTY. - 37332 D l FZ-6008-A ( ) GASKET KIT, Engine overhaul 37334 Dt FZ-6079-A ( 1 GASKET KIT, Valve grind

Find ... Go To..

TENNANT COMPANY LIMITED WARRANTY NEW MACHINES

Tennant Company warrants to the original purchaser for the period stated below that goods manufactured by it will be free from defects of workmanship and material, provided such goods are installed, operated. and maintained in accordance with Tennant Company's written manuals or other instructions. No warranty is made with respect t o items supplied by Tennant Company on speciai order of purchaser. Tennant Company's sole obligation under this Warranty will be to repair and replace, at Tennant Company's option. parts that do not conform to this Warranty.

SIX-MONTH LABOR COVERAGE (U.S.A. AND CANADA ONLY) For six (6) months in the U.S.A. or Canada, thirty (30) days elsewhere, from date of installation. Tennan: Company will, at its option, provide labor for repair, pay for outside repair service, or pay the customer straight time in accordance with Tennant Company's flat rate schedule for particular warranty repairs. After six (6) months, Tennant Company's sole obligation shall be limited to the repair or replacement, at Tennant Company's option, of parts that do not conform to this Warranty according to the schedule below.

BATTERIES AND TIRES Batteries and tires will be replaced if failure occurs due to defective material or workmanship within ninety (90) days from date of purchase. Thereafter, a pro rata adjustment from date of purchase to twelve (12) months will be made. The pro rata adjustmenf price af the replacement battery andlor tire.wiil be the fennant Company current price as of the adjustment request less 1112th of that price for each month remaining in the twelve (12) month period. This Warranty applies only to batteries and tires purchased from Tennant Company and installed in vehicles used in normal service.

BRUSHES Brushes that fail due to defective material or workmanship will be replaced on a pro rata basis within the first twelve (12) months of purchase. The replacement price will be calculated by multiplying the current Tennant Company price by the percentage of usable bristle remaining at the time of adjustment.

MACHINE WARRANTY PERIOD Tennant Company warrants its equipment for a set number of months or for a set number of hours of use, whichever comes first. The warranty periods and hours of use vary depending upon the machine model. The warranty periods for Tennant Company's various machines are:

SCARIFIERS Machine Model Warranty Period Machine Model Warranty Period G 12 months1500 hours 12 12 months1500 hours K4 12 months1500 hours RSITLR 12 months1500 hours KDC 12 months1500 hours

SCRUBBERS Machine Model Warranty Period Machine Model Warranty Period 426 12 months1500 hours 540E 12 months11 500 hours 432 12 months1500 hours 550 12 months11 500 hours 520 12 months/1500 hours 550E 12 monthsi1500 hours 527-11 12 months11 500 hours

[except engine and hydraulics-24 months12000 hours)

SWEEPERS Machine Model Warranty Period Machine Model Warraniy Period 42HD 12 months1500 hours 240 12 rnonths/1500 hours 140 12 months1500 hours 240EH SE 24 months11750 hours 186 18 months1500 hours 255 18 months11 500 hours 215 18 monthsi750 hours 2751275SE 24 months12000 hours 220 12 months11500 hours 365 24 months12000 hours 235 24 months11250 hours 92 GR 12 months11500 hours

(except Duramerc hopper 95 24 months/2000 hours 5 years15000 hours) 71 7 24 months11 500 hours

Find ... Go To..

RECONDITIONED MACHINES Tennant Companywarrants to the purchaser of reconditioned equipment, purchased from Tennant Company, for the period of ninety (90) days from the date of deiively that the purchased equipment will be free from defects of workmanship and material, provided such equipment is operated and maintained according to Tennant Company written manuals or instructions. Tennant Company's sole obiigation under this Warranty will be to repair and replace, at Tennant Company's option, pans that do not conform to this Warranty. No warranty of any kind is extended to equipment that is sold for salvage.

LABOR COVERAGE For thiny (30) days from date of delivery Tennant Company will, at its option, provide labor for repair, pay outside repair service, ar pay the customer straight time in accordance with Tennant Company flat rate schedule for particular warranty repair. After thirty (30) days, Tennant Company's sole obligation shall be limited t o the repair or replacem&ntnt, at Tennant Company's option. of parts that do not conform to this Warranty.

REPAIR PARTS Repair pans supplied by Tennant Company are warranted against defects for the period stated below. Tennant Company's ObliQation is limited to the replacement of the warranted part, and Tennant Company shall not be obligated t o provide labor (except certain engines also stated below) in installing such part.

ENGINES, SHORT BLOCKS, AND LONG BLOCKS Manufacturer Warranty Period Manufacturer Warranty Period Continental 1 year or 1500 hours parts 8 labor Perkins 1 year or 1500 hours parts & labor Kohler 1 year or 1500 hours parts 8 labor KuDOta 1 year or 1500 hours parts & labor

(except Kohler Model Kl8lS -500 hours) Briggs Stratton 90 days or 200 hours parts &lanor Wisconsin 1 year or 500 hours parts &labor Onan 1 year or 1500 hours parts 8 labor Ford 1 year or 1500 hours parts only

Engine Dart rePlaCements such as watef pwps. carburetors. and alternators are warranted for thirly (30) days pans only. m labor.

Labor is t o include only the time it takes to repair an engine. It does not include rernoval and replacement nor does it include travel tlme.

MAJOR HYDRAULIC COMPONENTS (PUMPS. MOTORS. CYLINDERS. AND CONTROL VALVES) Manufacturer Warranty Period Manufacturer Warranty Period Cessna 1 year parts oniy Oilgear 1 year parts only Char-Lynn 1 year parts only Gresen 90 days parts only Victor (Dukes) 1 year parts only MTE 90 days parts only Ross t year parts only Barnes 90 days parts only Vickers I year parts only All seal kits and replacement Parts are warranted for thirty (30) days parts oniy.

MAJOR ELECTRIC MOTORS Manufacturer Warranty Period Manulacrurer Warranty Period Baldor 1 year parts only Ohio Electric 1 year parts only General Electric 1 year parts only HK Porter 1 year parts only

Ail other repair parts are warranted for thirty (30) Gays oniy.

SERVICE LABOR Labor performed by a Tennant Company service representative shall be warranted for thiny (30) days from the date the repairs are completed. This policy does not cover work performed by any service company, other than Tennant Company, and is restricted to the specific repair operation or compcnent for which a claim is made.

THIS WARFIANTY IS EXPRESSLY IN LIEU OF ALL OTHER EXPRESSED OR IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS AND OF ALL OTHER OBLIGATIONS AND LIABILITIES ON THE PART OF TENNANT COMPANY, INCLUDING LIABILITIES FOR DIRECT, IMMEDIATE. SPECIAL. INDIRECT, OR CONSEOUENTIAL DAMAGES ARISING OUT OF THE FAILURE OF ANY MACHINE OR PART OF IT TO OPERATE PROPERLY, [NCLUDING THE COST OR EXPENSE OF PROVIDING SUBSTITUTE EQUIPMENT OR SERVICE DURING PERIODS OF MALFUNCTION OR NON-USE.

This Warranty cannot b e extended. changed, or modified by any representative of Tennant Company.

Find ... Go To..

TEN WANT ~ N W T COYPP~NY WORD HEAWUARTERS, M ~ N N ~ P ~ L I S , HN U.SA 0 Find ... Go To..

265 (002391- ) na parts manuald2z4qs2e3spnc1.cloudfront.net/...sn...parts_manual.pdf · operation,...

Documents