2015+ VW GTI/Audi S3 S-FLO Carbon Intake

Contact us with any installation questions. 215-658-1670 AWE-Tuning.com performance@AWE-Tuning.com

Congratulations on your purchase of the AWE Tuning S-FLO Carbon Intake for the 2015+ VW GTI and Audi S3.

Exquisite build quality and superior performance distinguishes this intake from all others.

Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0

INSTALLATION GUIDE

PERFORMANCE ENGINEERING FOR EUROPEAN AUTOS

2

1 S-FLO Carbon airbox 1 S-FLO Air 8lter 3 Mounting grommet 6 M5 x 20mm Button head bolt 1 Foam gasket Required Tools: T-25 Torx Phillips head screwdriver

PARTS LIST

Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0

Step 1

Figure 1

Remove the four T-25 Torx screws at arrows in Figure 1 and remove the upper half of the plastic inlet duct.

Step 2

Figure 1

Unclip the hose, at arrow in Figure 2, and remove the lower half of the plastic inlet duct.

3 Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0

Step 3

Figure 3

Step 4

Loosen both hose clamps from the factory intake tube, at ar-rows in Figure 4, and remove the hose.

Figure 4

Remove hose at Arrow A in Figure 3.

If vehicle is equipped with a secondary air pump, a hose will be present at Arrow B in Figure 3. If this hose is present, an AWE Tuning Breather Filter, sold separately, will be required. Re-move hose at Arrow B in Figure 3. See Step 6. A

B

Step 5

Pull straight up on the factory intake to pop it loose from the three pins holding it in place, shown at arrows in Figure 5.

Figure 5

4 Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0

Step 6

For secondary air pump equipped cars: Install the AWE Tuning Breather Filter, sold separately, to the secondary air pump intake hose, at Arrow A in Figure 6.

Next, zip tie the hose to an intake mount, as shown at Arrow B in Figure 6.

Install the supplied rubber grommets into the bottom of the lower section of the AWE Tuning S-FLO intake. Install the lower assembly into the engine bay by pressing the intake grommets onto the three posts.

Install the supplied foam gasket into the lower airbox groove, at arrow in Figure 7.

Figure 6

Figure 7

Step 7

Install the AWE Tuning S-FLO air 8lter onto the carbon 8ber tube of the airbox and tighten the clamp, at arrow in Figure 8, to secure the 8lter in place.

Step 8

Figure 8

B

A

5 Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0

Step 9

Re-install the factory intake tube and tighten the factory hose clamps.

Install the air box lid by using the supplied allen head bolts. Be sure not to over tighten the bolts as doing so could cause the carbon 8ber to crack.

Re-attach the rubber vent tube to the nipple on the AWE Tuning intake tube, at arrow in Figure 9.

Re-install the plastic inlet ducts that were removed in Steps 1 and 2.

Figure 9

ENJOY

Any questions or comments, please do not hesitate to contact us:

215-658-1670 AWE-Tuning.com performance@AWE-Tuning.com

PERFORMANCE ENGINEERING FOR EUROPEAN AUTOS

Remove the top lid allen head bolts to inspect the air 8lter element every 25,000 miles for integrity. Clean every 50,000 miles under normal operating conditions, sooner in dusty conditions. Contact AWE Tuning to purchase a 8lter maintenance kit.

6

Thank you for choosing AWE Tuning as your performance automotive parts supplier. Please remember that a performance car is only as strong as its weakest link. Therefore, it is vital that you maintain your vehicle to factory speci8cations.

By installing or using the purchased product, the Consumer accepts this warranty and any speci8c Manufacturer warranties enclosed.

Limited Warranty

The following warranty is valid only in the United States.

The Manufacturer’s full warranty applies to all products sold.

Secor Ltd. (AWE Tuning) warrants to the original retail purchaser (Consumer) this product (2015+ VW GTI/Audi S3 S-FLO Carbon Intake), from date of original purchase, against manufacturing defects for:

ONE YEAR

Upon veri8cation of warranty coverage, AWE Tuning will repair or replace the defective product at their discretion, without charge. This is the only remedy the Consumer has for any loss or damage, however arising, due to nonconformity in or defect of the product. This warranty does not cover consequential damage, loss of time or revenues, labor costs, shipping costs, inconvenience, loss of use of vehicle, dam-age to the vehicle or components, or other incidental or indirect damage.

All warranties are void if the product was not installed by a certi8ed auto mechanic, improperly serviced, modi8ed, or used in a way not intended by the Manufacturer. Use of product in Motorsports or Racing conditions is grounds for warranty denial. Motorsports and Racing is an inherently abusive operational condition, and it is impossible to warranty for this type of usage.

The Consumer is responsible for ensuring that the product is installed in a safe and proper manner, and should cease usage of the product immediately if an unsafe or improper condition is noted. If an unsafe or improper condition is noted, the Consumer should then immediately contact the facility where the product was installed or AWE Tuning directly.

Please contact the original place of purchase for any warranty claims or explanations of this document.

Copyright 2015, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Rev1.0

AWE Tuning 199 Precision DriveHorsham, PA 19044 215-658-1670performance@AWE-Tuning.com