2013 xtreme trim catalog 100812 - tamlyn.com trim catalog.pdf · colors shown are as accurate as...
TRANSCRIPT
COVER
© 2013 R.H. Tamlyn & Sons, LP
®XtremeTrim
Ventilation
XtremeColor Flashing
Water Management
®
Versatile Design Options . Aesthetically Pleasing . Sustainable . Durable . Lightweight
Intexure Architects, Houston, Texas
For use with siding and soffit
ProLine Plank Flash ...................... 35PLPFUS Patent #7,721,488
®
Table of Contents
2 www.tamlyn.com © 2013 TAMLYN
® XtremeTrim Butt Joint Flashing
Plank Flash .................................... 35PFUS Patent #7,721,488
Horizontal Bead Reveal ................. 9BRH
Horizontal Board Reveal ................ 17RHB
Horizontal Reveal ........................... 16RH
Horizontal Z .................................... 15CQZ
Horizontal Z .................................... 15XZH
Bullnose Inside Corner .................. 29XICB
Inside Corner .................................. 20XIC / XICJUS Patent #5,960,598
Low Profile Plank Inside Corner ... 23XICLP
Low Profile Panel Inside Corner ... 22XICLP
Panel Inside Corner ....................... 21XICUS Patent #5,960,598
F Reveal .......................................... 32FR
® XtremeTrim Horizontal Reveal
J Mold .............................................. 11JMH
Standard H Mold ............................. 6XHM
Transition Vertical Reveal .............. 14RVT
Vertical Batten Reveal .................... 18RVBN
Vertical Bead Reveal ...................... 8BRV
Vertical Board Reveal .................... 13RVB
Vertical Siding H Mold ................... 7SHM
Vertical T Mold ................................ 10TM
® XtremeTrim Vertical Reveal
® XtremeTrim Inside Corner
® XtremeTrim Outside Corner
3-1/2" Outside Corner .................... 31XOC
Batten Corner ................................. 19XOCBN
Blunt Panel Outside Corner .......... 26XOCBL
Bullnose Outside Corner ............... 30XOCB
Butted Outside Corner ................... 27XOCBT
Low Profile Outside Corner ........... 24XOCLP
Reveal Outside Corner .................. 25XOCR
Transition Outside Corner ............. 28XOCB
Starter Strip .................................... 33XS
® XtremeTrim Starter Strip
® XtremeTrim Soffit Transition Trim
Starter Strip .................................... 32XS
F Reveal .......................................... 32FR
Horizontal Z .................................... 15XZS
Window Flashing ............................ 34XWF
® XtremeTrim Vertical Reveal
Vertical Reveal ................................ 12RV
Vertical Reveal ................................ 12RV58
Horizontal Board Reveal ................ 17RHBG
Vertical Board Reveal .................... 13RVBG
®What is XtremeTrim
XtremeTrim® consists primarily of extruded aluminum profiles for fiber cement siding & soffit and other materials.
XtremeTrim® profiles are designed to work together as a system to create an aesthetically attractive and durable appearance.
It is a highly value-added product allowing many different, durable and dramatic design options not available using other materials.
XtremeTrim® is made from 75 to 100 % post industrial and post consumer scrap, extruded aluminum trim meets requirements for sustainability and can contribute to LEED® points.
XtremeTrim® extruded items are sustainable trim that is fabricated from custom die-extruded heavy duty 6063 T-5 aluminum alloy with a coating that protects against harsh weather conditions and allows for paint adhesion.
Painting Guide
Use Direct to Metal (DTM) paint with XtremeTrim®; consult with your local paint manufacturer for best practice and proper painting methods. Always follow the paint manufacturer’s recommendations to apply.
J Mold .............................................. 11JMS
BRH .......... Horizontal Bead Reveal
PF ............. Plank Flash ...................................... 35PLPF ......... ProLine Plank Flash ......................... 35
................... 9BRV........... Vertical Bead Reveal ........................ 8CQZ .......... Horizontal Z...................................... 15FR ............. F Reveal ........................................... 32JMH........... J Mold ............................................... 11JMS........... J Mold ............................................... 11
RH............. Horizontal Reveal ............................. 16RHB .......... Horizontal Board Reveal .................. 17RHBG........ Horizontal Board Reveal .................. 17RV ............. Vertical Reveal ................................. 12RVB........... Vertical Board Reveal....................... 13RVBG........ Vertical Board Reveal....................... 13RVBN ........ Vertical Batten Reveal ..................... 18RVT........... Transition Vertical Reveal ................ 14SHM .......... Siding H Mold .................................. 7TM............. Vertical T Mold ................................. 10XHM .......... Standard H Mold .............................. 6XIC ............ Inside Corner.................................... 20XICB.......... Bullnose Inside Corner..................... 29XICLP ....... Low Profile Inside Corner................. 22XOC .......... Outside Corner ................................ 12XOCB........ Bullnose Outside Corner .................. 28XOCBL...... Blunt Panel Outside Corner ............. 26XOCBN ..... Batten Corner .................................. 19XOCBT...... Butted Outside Corner .................... 27XOCLP...... Low Profile Outside Corner ............. 24XOCR........ Reveal Outside Corner .................... 25XS ............. Starter Strip ...................................... 32XZH........... Horizontal Z ..................................... 15XZS ........... Horizontal Z ..................................... 15
Alphabetical Listing
3
®
Table of Contents
© 2013 TAMLYN www.tamlyn.com
Ezvent® ........................................... 37EZV
Soffit / Ventilation Products
Snapvent® ...................................... 36SV
Soffit H-Mold (soffit use only) ....... 38HM
Soffit Vent Connector Clip ............. 38CONNCLIP
Weep Strip ....................................... 39VSZ
Vent Strip ........................................ 39VSJ
Hat Shaped Vent ............................. 37CUV
PVC Trim Painting Guide
Tamlyn PVC Trim may be painted to achieve a custom color.
Use a light color, 100% acrylic latex paint with a light reflective value (LRV) of 55 or higher (Flat Black=0, pure white=100). Painting PVC trim with dark colors may cause the product to warp.
Tamlyn does not recommend painting our PVC products with dark colors unless a good quality heat reflective paint is used such as Sherwin-Williams Vinyl Safe™, and that it is applied according to the paint manufacturer’s recommended application instructions.
If a dark color (LRV value of 50 or lower/darker) paint is used, excess solar heat may be absorbed, subjecting the PVC to warping and distortion due to extremes of thermal expansion and contraction. This reaction is even more evident when these parts are exposed to direct sunlight in hot climates. Paint adhesion loss, blistering and peeling may also result.
Failure to use heat reflective dark color paints on Tamlyn PVC products will void warranty and Tamlyn will not be responsible for repair or replacement of any resulting damage due to distortion, warping, buckling, shrinkage, paint blistering, or peeling of paint on the PVC products, or repair or replacement of related siding, soffit, or trim products.
Always follow the paint manufacturer’s recommendations to apply.
Make sure Tamlyn PVC Trim is clean and dry before painting.
Counter Flashing ........................... 402TF
XtremeColor Flashing
Angle/Base Flashing ...................... 41BF
Step Flashing .................................. 41FS
Overhang Roof Edge ..................... 42DL
Gravel Stop Roof Edge .................. 43GS
Angle Roof Edge ............................ 42ME
Reglet Flashing .............................. 40RF
XtremeColor Flashing
Fascia Cap Roof Edge .................. 43FC
Deck Ledger Flashing .................... 44VWF
Inside Corner .................................. 45XIC, XICJ, XICS
Outside Corner ............................... 45XOCBT
Z Flashing ....................................... 46VZB
Individual Outside Corner ............. 46OCI
Window Flashing ............................ 44VWF
J Flashing ....................................... 47JMF
Parapet/Coping Flashing ............... 47PCF
Horizontal Transition ..................... 48HBD
Brick/Stone Ledger Flashing ........ 48BL
XtremeCoil ...................................... 49TC
Kick Out Flashing ........................... 49KOFL, KOFR
Counter Flashing ........................... 40F2TF
Counter Flashing ........................... 40CF
Reglet Flashing .............................. 40RF
Angle/Base Flashing ...................... 41BFH
Angle/Base Flashing ...................... 41BFHH
Angle/Base Flashing ...................... 41BFRH
Angle Roof Edge ............................ 42MG
Water Management
HardiePanel, HardiePlank, HardieSoffit, JamesHardie, Recommended logo are trademarks or registered trademarks of
James Hardie Technology Limited
TamlynWrap™ ................................ 50Drainable House WrapDHW
Tamlyn Window Tape ..................... 50WS
Utility Moisture Flash ..................... 51UMF
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
TAMLYN
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
UTI
LITY
MO
ISTU
RE F
LASH
Tamlyn Color Sealant ..................... 51XB9500COLOR SEALANT
USE R
OLL
ER T
O A
PPLY
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLY
USE R
OLL
ER T
O A
PPLY
TAMLY
N
USE R
OLL
ER T
O A
PPLY
TAMLY
N
USE R
OLL
ER T
O A
PPLYTAM
LYN
®®
USE R
OLL
ER T
O A
PPLY
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLY
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLY
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLYTAM
LYN
®®
USE R
OLL
ER T
O A
PPLY
TAMLY
N
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLY
TAMLY
NTAM
LYN
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLY
Counter Flashing ........................... 40FTF4
BF ............. Angle/Base FlashingAngle/Base FlashingAngle/Base FlashingAngle/Base Flashing
BL.............. Brick/Stone Ledger Flashing ............ 482TF............ Counter Flashing.............................. 40
Counter Flashing.............................. 40Counter Flashing.............................. 40Counter Flashing.............................. 40
........................ 41BFH........... ........................ 41BFHH ........ ........................ 41BFRH ........ ........................ 41ME............. Angle Roof Edge ............................. 42MG ............ Angle Roof Edge ............................. 42
F2TF ......... CF ............. FTF4 ......... VWF .......... Deck Ledger Flashing ...................... 44FC ............. Fascia Cap Roof Edge ..................... 43GS............. Gravel Stop Roof Edge .................... 43HBD .......... Horizontal Transition ....................... 48OCI............ Individual Outside Corner ................ 46XIC ............ Inside Corner ................................... 45XICJ .......... Inside Corner ................................... 45XICS.......... Inside Corner ................................... 45JMF ........... J Flashing ........................................ 47KOFL......... Kick Out Flashing ............................. 49KOFR ........ Kick Out Flashing ............................. 49XOCBT...... Outside Corner................................. 45DL ............. Overhang Rood Edge ...................... 42PCF........... Parapet/Coping Flashing ................. 47RF ............. Reglet Flashing ................................ 40FS ............. Step Flashing ................................... 41VWF .......... Window Flashing ............................. 44TC ............. XtremeCoil ....................................... 49VZB ........... Z Flashing ....................................... 46
Alphabetical Listing
Colors shown are as accurate as printing methods will permit. Please see actual product sample for true color. Product and color availability vary by region and are subject to change. There will be color variance lot to lot.
Tamlyn warrants defective-free products for a period of 10 years for the original purchaser unless otherwise stated for the specific product ordered. Tamlyn products are further warranted as to adequacy of design, provided products are properly specified and installed. This warranty does not apply in the event products are altered in any way or are improperly installed. Liability is limited to replacement of products proven to be defective. Tamlyn has made no other warranty, express or implied, regarding its products, including but not limited to, any warranty regarding merchantability or fitness for a specific purpose. Any claim that a product is defective must be brought within 1 month of the date of installation of such products to the original purchaser. Customer hereby agrees that no other incidental or consequential damages are the responsibility of Tamlyn.
The following voids any warranty regarding Tamlyn products:Ÿ Product has been improperly installedŸ Accepted siding installation methods have not been
followed Ÿ Building codes have not been followed Ÿ The building envelope has not been properly installed Ÿ Products not installed by a contractor/installer with
common knowledge of the building industry
Responsibility remains with the architect or engineer, contractor and owner for the design, application and proper installation of each Tamlyn product. Specifier and user shall determine the suitability of products for specific application and assume all responsibilities in connection there within.
XtremeTrim® - Aluminum does not rust, however it does corrode. XtremeTrim® has a protective coating to cover the bare aluminum. When making cuts on XtremeTrim® recoating will be required at ends, surface scratches or when performing form cuts. Failure to do this voids your warranty. For answers to your technical questions on recoating consult your local paint manufacturer before installation. Please refer to XtremeTrim® painting guide.
PVC Trim - The PVC TAMLYN buys is an industry-standard, rigid, durable, chemically resistant product designed for outdoor weatherability. While the PVC is paintable, we cannot know what may be added to paints, primers etc. that could affect the PVC. Installers must consult with the paint manufacturer recommendations on priming and painting PVC. Where parts are designed to work together, TAMLYN vinyl products are not warranted if installed in conjunction with other non-Tamlyn vinyl products.
TAMLYN PVC Trim may be painted to achieve a custom color. Use a light color, 100% acrylic latex paint with a light reflective value (LRV) of 55 or higher (Flat Black=0, pure white=100). Painting PVC trim with dark colors may cause the product to warp. TAMLYN does not recommend painting our PVC products with dark colors If a dark color (LRV value of 50 or lower/darker) paint is used, excess solar heat may be absorbed, subjecting the PVC to warping and distortion due to extremes of thermal expansion and contraction. This reaction is even more evident when these parts are exposed to direct sunlight in hot climates. Paint adhesion loss, blistering and peeling may also result.
TAMLYN will not be responsible for repair or replacement of any resulting damage due to distortion, warping, buckling, shrinkage, paint blistering, or peeling of paint on the PVC products, or repair or replacement of related siding, soffit, or trim products if dark colors were used.
Follow the paint manufacturer’s recommendations to apply. Make sure TAMLYN PVC Trim is clean and dry before painting.
Note re flammability: PVC products will not support or spread flames. They are self-extinguishing as soon as the flame source is removed.
Please follow siding manufacturers best practice application when installing any Tamlyn accessory. Xtreme Trim™ profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope. Xtreme Trim™ products are not part of an Exterior Insulation Finishing System (EIFS) and are not designed or intended to be used in an EIFS or similar system.
Limited Warranty
®
General Information
4 www.tamlyn.com © 2013 TAMLYN
Color Palette
TAMLYN was established in May 1971 by Ron Tamlyn, Sr. with $800 borrowed money and help from his wife, Jean, in a small shack in the back yard of their modest home in Bellaire, Texas. We remain family-owned to this day. Our history is one of quality, innovation, and proven performance. We are proud to represent the manufacturing end of the building products industry, and remain a competitive manufacturer committed to making products in America, giving customers a choice and not putting all their eggs in an uncertain import basket. An overwhelming majority of our products are still made in the USA. We believe it matters in helping America keep control of its destiny.
Tamlyn manufactures Xtreme Trim® for fiber cement, roofing products and structural metal products for stronger homes and buildings that will hold together under high wind and seismic forces.
Tamlyn provides a full line of XtremeColor Flashings recommended for use with HardiePanel® and HardiePlank® sidings and other quality siding products. XtremeColor Flashing is recommended by James Hardie because it is made to exactly color match their pre-finished fiber cement sidings to comply with their warranty. Tamlyn provides tough, weather-resistant coatings for a long lasting beauty and low maintenance on XtremeColor Flashing. Easy to install with all fiber cement siding and soffit products.
A very diversified mix of frequently needed building products is available from Tamlyn. We manufacture joist and truss hangers, brick ties, hurricane clips, straps, and holdowns, as well as special and custom welded hangers. Tamlyn structural products are ICC-listed and Florida Building Code-approved. We also make G-185 triple zinc connectors for use with the new ACQ treated wood products.
We offer quality products, competitive prices, and fast service. While we recognize we are in a global economy, we remain committed to making products by choice in the USA, giving customers a quality domestic option.
To become a world-class and world-wide supplier of quality building products. We will help build the dream of better homes, continually innovating, while honoring our heritage as a family business that values all employees, making Tamlyn a rewarding place to work. We will promote positive, lasting relationships with customers, providing excellent products at fair prices with superior service. We commit to be good stewards of our resources to leave Tamlyn in a stronger position for the next generation, passing these values on and bringing glory to God in all we do.
Corporate Headquarters / Plant13623 Pike RoadStafford, Texas 77477USA Toll Free 800-334-1676Phone: 281-499-9604Fax: 281-499-8948Technical support: 713-562-5149
Dallas Plant10940 Petal StreetDallas, Texas 75238USA Toll Free 888-416-9676Phone: 214-348-9676 Fax: 214-348-0976
About Tamlyn
Mission Statement
Company Directory
5
®
© 2013 TAMLYN www.tamlyn.com
®XtremeTrim Best Practices Installation
While we design all our XtremeTrim® with drain dams for vertical runs and shingle fashion for horizontal profiles, its primary design is for aesthetics. XtremeTrim® will not stop all water from penetrating the surface of the cladding. The primary insurance of moisture mitigation for the building envelope is your house wrap, a drainable house wrap. Other options are to use skin venting along with your house wrap. We recommend that you consult your siding manufacturer for best practice application when installing XtremeTrim® with their siding. As all building professionals know, water is the most significant factor in the premature deterioration of buildings, and why proper steps should always be taken to protect the envelope.
Leakage paths exist at any opening in the wall surface, whether intended or unintended. Joints between materials and around windows and doors, vents, cracks, and porous surfaces are all potential entry points for water. This is why all roof parapets must be properly sealed with flashing membrane and all windows and door openings flashed in shingle fashion.
All XtremeTrim® profiles do not form a moisture management system. The architect, builder, designer and contractor are responsible for designing and installing a code compliant building envelope. Below are the code minimum requirements.
Tamlyn XtremeTrim® products are not part of an EIFS system and not designed or intended to be used in an EIFS or similar system.
INTERNATIONAL RESIDENTIAL CODE 2006
WALL COVERING - SECTION R703 EXTERIOR COVERING
R703.1 General.
The exterior wall envelope shall be designed and constructed in such a manner that prevents the accumulation of water within the wall assembly by providing a water-resistive barrier behind the exterior veneer as required by Section R703.2 and a means of draining water that enters the assembly to the exterior.
R703.8. Flashing.
EXTERIOR WALLS - SECTION 1403 PERFORMANCE REQUIREMENTS
IBC § 1403.2:
. The exterior wall envelope shall be designed and constructed in such a manner as to prevent the accumulation of water within the wall assembly by providing a water-resistant barrier behind the exterior veneer, as described in Section 1404.2, and a means for draining water that enters the assembly to the exterior. Protection against condensation in the exterior wall assembly shall be provided in accordance with the International Energy Conservation Code.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
Exterior walls shall provide the building with a weather-resistant exterior wall envelope. The exterior wall envelope shall include flashing as described in Section R703.8
Approved corrosion-resistive flashing shall be applied shingle-fashion in such a manner to prevent entry of water into the wall cavity or penetration of water to the building structural framing components. The flashing shall extend to the surface of the exterior wall finish. Approved corrosion-resistant flashings shall be installed at all of the following locations:
Weather protection. Exterior walls shall provide the building with a weather resistant exterior wall envelope. The exterior wall envelope shall include flashing, as described in Section 1405.3
TamlynWrap™Drainable House Wrap
Weep Strip
Water ResistiveBarrier
Rainscreen
Weep Strip
Best Practices Installation Option #1
Best Practices Installation Option #2
DESIGN FEATURE: Designed to work as a system component with Tamlyn vinyl soffit vent products. Covers the end seams of the soffit material and vents, providing a cleaner transition than simply butting the vents and panels end to end.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Use of the XtremeTrim® H-Mold at horizontal joints is not recommended.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
PRODUCT DETAIL:
AVAILABLE SIZES:
®®
XtremeTrim Standard H-Mold
1"
1/2"
Siding/SoffitSize
Framing Member
XtremeTrim® Standard H-Mold
Soffit Panel
6 www.tamlyn.com © 2013 TAMLYN
EXTRUDED ALUMINUM
TamlynWrap™Drainable
House Wrap
Stud
Stud
WallSheathing
Vertical Siding
XtremeTrim® Standard H-Mold
3/8" beadof polyurethane
sealant
ITEM ID LENGTH
XHM148
XHM5168
SIDING SIZE
8'
8'
1/4" (6mm)
5/16" (8mm)
Rafter
Ledger
Blocking
Subfascia
Water Resistive Barrier
Soffit Panel
XtremeTrim®Horizontal Z
Tamlyn Window Tape
Drainable HouseWrap
SEALANT
XtremeTrim® Standard H-Mold
Vertical Siding
Weep Strip
DESIGN FEATURE: Designed to cover vertical joints in vertical siding. Longer lasting and more effective than contractor grade caulk. Provides a smooth seam at joints.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Use of the XtremeTrim® Vertical Siding H-Mold at horizontal joints is not recommended.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
7© 2013 TAMLYN www.tamlyn.com
®XtremeTrim Vertical Siding H-Mold
EXTRUDED ALUMINUM
ITEM ID LENGTH
SHM5168
SHM51610
SHM7168
SHM71610
SHM588
SHM5810
SIDING SIZE
10'
8'
10'
8'
10'
8'5/16" (8mm)
5/16" (8mm)
7/16" (11mm)
7/16" (11mm)
5/8" (16mm)
5/8" (16mm)
XtremeTrim®Horizontal
Bead Reveal
Stud
XtremeTrim® Vertical Siding H-Mold
Tamlyn Window Tape
Vertical Siding
3/8" beadof polyurethane
sealant
SEALANT
Weep Strip
PRODUCT DETAIL:
AVAILABLE SIZES:
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
1-1/2"
1/2"
SidingSize
XtremeTrim® Vertical Siding H-Mold
®
PRODUCT DETAIL:
AVAILABLE SIZES:
DESIGN FEATURE: XtremeTrim® Vertical Bead Reveal serves as an aesthetic expansion joint between panels on the wall of your home or larger project. Works with all panel profiles/ finishes. A better, more appealing and secure solution to the “open wall” vertical joint look popular in many areas.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Use of the XtremeTrim® Vertical Bead Reveal at horizontal joints is not recommended.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
®®XtremeTrim Vertical Bead Reveal
8 www.tamlyn.com © 2013 TAMLYN
EXTRUDED ALUMINUM
ITEM ID LENGTH
BRV14516
BRV12516
BRV12716
BRV1258
REVEAL
10'
10'
10'
10'
1/4"
1/2"
1/2"
1/2"
1/4" Reveal
1-1/2"
1/2" Reveal
1-1/2"
1/4" Reveal
1/2" Reveal
SIDING SIZE
5/16" (8mm)
5/16" (8mm)
7/16" (11mm)
5/8" (16mm)
XtremeTrim® Vertical Bead Reveal
XtremeTrim®Horizontal Bead Reveal
Stud
XtremeTrim® Vertical Bead Reveal
Tamlyn Window Tape
Vertical Siding
3/8" beadof polyurethane
sealant
Weep Strip
SEALANT
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
SidingSize
SidingSize
DESIGN FEATURE: Designed to work as a system with Vertical Bead Reveal. XtremeTrim® Horizontal Bead Reveal provides a minimal exposure aesthetic while providing protection for the top edge of the lower panel.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Do not install Horizontal Bead Reveal on Horizontal applications where the exterior flange can catch water.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
PRODUCT DETAIL:
AVAILABLE SIZES:
9© 2013 TAMLYN www.tamlyn.com
®®XtremeTrim Horizontal Bead Reveal
EXTRUDED ALUMINUM
Siding Size
5/8"
1/8"
1/4"
1/4"
1-3/4"
Rafter
Subfascia
Soffit
WallSheathing
Ledger
Vertical Siding
XtremeTrim®HorizontalBead Reveal
Tamlyn Widow Tape
1/4" reveal line
1/2" reveal line
ITEM ID LENGTH
BRH516
BRH716
BRH58
10'
10'
10'
5/16" (8mm)
7/16" (11mm)
5/8" (16mm)
SIDING SIZE
XtremeTrim®Horizontal Bead Reveal
Stud
XtremeTrim® Vertical Bead Reveal
Tamlyn Window Tape
Vertical Siding
Weep Strip
SEALANT
3/8" beadof polyurethane
sealant
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
93°
PRODUCT DETAIL:
AVAILABLE SIZES:
DESIGN FEATURE: XtremeTrim® Vertical Panelseam® T-Mold serves as a minimal exposure expansion joint between panels. Works with all panel profiles/ finishes.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Use of the XtremeTrim® Panelseam® T-Mold at horizontal joints is not recommended.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
®® ®XtremeTrim Vertical Panelseam T-Mold
10 www.tamlyn.com © 2013 TAMLYN
EXTRUDED ALUMINUM
1-1/2"
3/8"
US Patent #6,032,426, US Trademark #2,358,771
Stud
WallSheathing
XtremeTrim® VerticalPanelseam® T-Mold
Vertical Siding3/8" bead
of polyurethanesealant
XtremeTrim®Horizontal Bead Reveal
Stud
Tamlyn Window Tape
Vertical Siding
Weep Strip
SEALANT
XtremeTrim® VerticalPanelseam® T-Mold
ITEM ID LENGTH
TM158 8'
3/8" beadof polyurethane
sealant
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
PRODUCT DETAIL:
AVAILABLE SIZES:
11© 2013 TAMLYN www.tamlyn.com
®®XtremeTrim J-Mold
EXTRUDED ALUMINUM
Rafter
Soffit
XtremeTrim®J-Mold
Wall Sheathing
Vertical Siding
XtremeTrim®J-Mold
DrainableHouse Wrap
Wall Sheathing
Lap Siding
Brick Ledge Flashing
SEALANT
3/8" beadof polyurethane
sealant
DESIGN FEATURE: Provides a cleaner finish at openings and the edges of panels or planks.
JMH - Designed to work in conjunction with XtremeTrim® Horizontal Bead Reveal, Vertical Reveal, and Horizontal Z.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: JMH .050" (1.27mm) ± .005JMS .037" (0.94mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Do not install XtremeTrim® J mold on Horizontal applications where the exterior flange can catch water.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
1"SidingSize
JMS Series JMH Series
1-1/8"
3/8"3/8"
ITEM ID LENGTH
JMS5168
JMS7168
JMS588
JMH51610
JMH71610
JMH5810
JMH3410
SIDING SIZE
8'
8'
8'
10'
10'
10'
10'
5/16" (8mm)
7/16" (11mm)
5/8" (16mm)
5/16" (8mm)
7/16" (11mm)
5/8" (16mm)
5/16" Lap SidingTamlynWrap™
Drainable House Wrap
Subfascia
Soffit Panel
TamlynWrap™Drainable
House Wrap
XtremeTrim®J-Mold
XtremeTrim®J-Mold
XtremeTrim®Siding H-Mold
Vertical Siding
SidingSize
®®XtremeTrim Vertical Reveal
12 www.tamlyn.com © 2013 TAMLYN
EXTRUDED ALUMINUM
Double Stud or Nail Block
XtremeTrim® Vertical Reveal
3/8" beadof polyurethane
sealant
PRODUCT DETAIL:
AVAILABLE SIZES:
2-3/4"
1/2"
Siding Size
3/8"3/8"
ITEM ID LENGTH
RV516
RV716
RV58
RV34
SIDING SIZE
10'
10'
10'
10'
5/16" (8mm)
7/16" (11mm)
5/8" (16mm)
5/16" Lap Siding
DESIGN FEATURE: Designed to create a uniform, aesthetically consistent vertical reveal between panels or lap sidings.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Use of the XtremeTrim® Vertical Reveal at horizontal joints is not recommended.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
TamlynWrap™Drainable
House Wrap
Wall Sheathing
XtremeTrim®Horizontal Z
XtremeTrim® Vertical Reveal
TamlynWindow Tape
Vertical Siding
SEALANT
3/8" beadof polyurethane
sealant
Weep Strip
TamlynWrap™Drainable
House Wrap
WallSheathing
SEALANT
3/8" beadof polyurethane
sealant
Lap Siding
XtremeTrim® Reveal Outside Corner
XtremeTrim® Vertical Reveal
TamlynWindow Tape
TamlynWrap™Drainable
House Wrap
Vertical or Lap Siding
REVEAL
1/2"
1/2"
1/2"
3/4"
RV
3"
5/8"3/4"5/8"
3/4"RV34
1-3/4"
1/2" 3/8"3/8"
5/8"
RV58
13© 2013 TAMLYN www.tamlyn.com
®®XtremeTrim Vertical Board Reveal
EXTRUDED ALUMINUM
3/8" beadof polyurethane
sealant
PRODUCT DETAIL:
AVAILABLE SIZES:
2-1/4"
DESIGN FEATURE: Produces a broad vertical accent between siding panels while not protruding beyond the plane of the facade.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Use of the XtremeTrim® Double Vertical Reveal at horizontal joints is not recommended.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
Double Stud or Nail Block
XtremeTrim® Vertical Board Reveal
TamlynWrap™Drainable
House Wrap
Vertical Siding
SidingSize
1/2"3/8"
Wall Sheathing
XtremeTrim®Horizontal Z
TamlynWindow Tape
Vertical Siding
3/8" beadof polyurethane
sealant
Weep Strip
TamlynWrap™Drainable
House Wrap
SEALANT
ITEM ID LENGTH
RVB516
RVB716
RVBG516
RVBG716
SIDING SIZE
10'
10'
10'
10'
5/16" (8mm)
7/16" (11mm)
5/16" (8mm)
7/16" (11mm)
RVB
2-1/4"SidingSize
1/2"3/8"
RVBG
RVB Series
RVBG Series
PRODUCT DETAIL:
AVAILABLE SIZES:
®®
XtremeTrim Transition Vertical Reveal
14 www.tamlyn.com © 2013 TAMLYN
EXTRUDED ALUMINUM
ITEM ID LENGTH
RVT51634 10'
2-3/4"
1/2"
3/4"
3/8"
3/8"
Double Stud or Nail Block
VerticalSiding
XtremeTrim® Transition Vertical Reveal
Wall Sheathing
XtremeTrim®Horizontal Z
Termination Piece
Stud
VerticalSiding
3/8" beadof polyurethane
sealant
Tamlyn Window Tape
3/8"
XtremeTrim® Transition Vertical Reveal
Lap Siding
3/8" beadof polyurethane
sealant
SEALANT
Lap Siding
use polyurethanesealant to
seal the seams
Weep Strip
DESIGN FEATURE: Designed to create a uniform, aesthetically consistent vertical reveal at transitions between panels and lap sidings.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Use of the XtremeTrim® Transition Vertical Reveal at horizontal joints is not recommended.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
15© 2013 TAMLYN www.tamlyn.com
®® XtremeTrim Horizontal Z
EXTRUDED ALUMINUM
DESIGN FEATURE: Designed to work in conjunction with XtremeTrim® Vertical Reveal and siding H-Mold. XZH5163 provides greater flexibility in reveal size.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: XZS .030" (0.76mm) ± .005CQZ, XZH .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply waterproofing membrane on trim before setting panels to help minimize water intrusion behind siding
NOTE: Do not install XtremeTrim® Horizontal Z on horizontal applicationswhere the exterior flange can catch water.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
PRODUCT DETAIL:
AVAILABLE SIZES:
ITEM ID LTH
XZS5168
XZS7168
XZS588
XZH516
XZH716
XZH58
XZH5163
CQZ
SIDING SIZE
8'
8'
8'
10'
10'
10'
10'
10'
5/16" (8mm)
7/16" (11mm)
5/8" (16mm)
5/16" (8mm)
7/16" (11mm)
5/8" (16mm)
5/16" (8mm)
5/16" (8mm)
3/4
"
SidingSize
3/8"
XZS
1-1
/2"
93°
XZH
SidingSize
3/8"
3-1
/2"
SidingSize
93°
XZH5163
3/8"
MAX REVEAL
1/4"
1/4"
1/4"
1"
1"
1"
2-1/2"
3/4"
1-1
/4"
1-1
/4"
3/8"
CQZ
Rafter
Soffit
Wall Sheathing
Vertical Siding
Ledger
XZH5163 XtremeTrim® Horizontal Z
See the table for max reveal size
TamlynWrap™Drainable House Wrap
Tamlyn Window Tape
Horizontal Z Termination Piece: Pre cut ends for termination intooutside or inside corner trims.One end has left hand cut with the other end having a right end cut.
XZHT516
XtremeTrim® Horizontal Z
Vertical Siding
XtremeTrim® Vertical Reveal
Weep Strip
TamlynWrap™Drainable
House Wrap
TamlynWindow
Tape
Wall Sheathing
Vertical Siding
CQZ
TamlynWrap™Drainable House Wrap
TamlynWindow Tape
See the table formax reveal size
®®XtremeTrim Horizontal Reveal
16 www.tamlyn.com © 2013 TAMLYN
EXTRUDED ALUMINUM
DESIGN FEATURE: Profile gives a horizontal reveal consistent with and complimentary to the Vertical Reveal.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply waterproofing membrane on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Do not install XtremeTrim® Double Horizontal Reveal on horizontal applications where the exterior flange can catch water.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
Rafter
Subfascia
Soffit
Wall Sheathing
VerticalSiding
Ledger
XtremeTrim®Horizontal Reveal
1/4" to 1" Reveal
Stud
XtremeTrim®Horizontal Reveal
Tamlyn Window Tape
ITEM ID LENGTH
RH516 10'
SIDING SIZE
5/16" (8mm)
Vertical Siding
XtremeTrim® Vertical Reveal
3/8" beadof polyurethane
sealant
SEALANT
Weep Strip
PRODUCT DETAIL:
AVAILABLE SIZES:
2"
93°
3/8"
93°
SidingSize
3/8"
1/2" TamlynWrap™Drainable
House Wrap
Tamlyn Window Tape
TamlynWrap™Drainable
House Wrap
DESIGN FEATURE: Design creates a broad horizontal accent within the plane of the wall without protruding beyond.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply waterproofing membrane on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Do not install XtremeTrim® Horizontal Reveal on horizontal applications where the exterior flange can catch water.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
17© 2013 TAMLYN www.tamlyn.com
®® XtremeTrim Horizontal Board Reveal
EXTRUDED ALUMINUM
PRODUCT DETAIL:
AVAILABLE SIZES:
3/8"
1/2"
2-1/4"
Siding Size
ITEM ID LENGTHSIDING SIZE
RHB516
RHB716
RHBG516
RHBG716
10'
10'
10'
10'
5/16" (8mm)
7/16" (11mm)
5/16" (8mm)
7/16" (11mm)
RHB RHBGRafter
Subfascia
Soffit
Wall Sheathing
Vertical Siding
XtremeTrim®HorizontalGroovedBoard Reveal
TamlynWrap™Drainable House Wrap
Weep Strip
TamlynWrap™Drainable
House Wrap
TamlynWindow
TapeSEALANT
3/8" beadof polyurethane
sealant
VerticalSiding
93°
93°
3/8"
1/2"
2-1/4"
Siding Size
93°
93°
RHB
RHBGTamlynWindowTape
XtremeTrim®HorizontalBoard Reveal
XtremeTrim® Vertical Board Reveal
DESIGN FEATURE: Unique design duplicates the look of a wood batten without the maintenance headaches while serving as a rustproof flashing between vertical siding.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
FASTENING: Do not fasten edges of panels until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite panel edges.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
NOTE: Use of the XtremeTrim® VerticalBatten Reveal at horizontal joints is not recommended.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
®®XtremeTrim Vertical Batten Reveal
18 www.tamlyn.com © 2013 TAMLYN
EXTRUDED ALUMINUM
PRODUCT DETAIL:
AVAILABLE SIZES:
XtremeTrim®Vertical Batten Reveal
Top PlateStud
Wall SheathingVertical
Siding
XtremeTrim®Batten Corner
XtremeTrim® Vertical Batten Reveal
Vertical Siding
Wall Sheathing
SEALANT
3/8" beadof polyurethane
sealant
WindowTape
1/2"1/2"
1"1" SidingSize
1/2"
ITEM ID LENGTH
RVBN516 10'
SIDING SIZE
5/16" (8mm)
XtremeTrim®Batten Corner
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
Wall Sheathing
Top PlateStud
XtremeTrim®Batten Corner
Vertical Siding
XtremeTrim®Batten Corner
Stud
XtremeTrim® Vertical Batten Reveal
Vertical Siding
Wall Sheathing
3/8" beadof polyurethane
sealant
SEALANT
TamlynWindow Tape
XtremeTrim® Vertical Batten Reveal
Tamlyn Window Tape
Outside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
19© 2013 TAMLYN www.tamlyn.com
®®XtremeTrim Batten Corner
EXTRUDED ALUMINUM
PRODUCT DETAIL:
AVAILABLE SIZES:
1/2"
SidingSize
1/2"
ITEM ID LENGTH
XOCBN 10'
SIDING SIZE
5/16" (8mm)
DESIGN FEATURE: Offers a bold, unique corner for vertical siding panels. Works best visually with Batten Reveal and Vertical Reveal.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
Outside Corner
1"
PRODUCT DETAIL:
AVAILABLE SIZES:
20 www.tamlyn.com © 2013 TAMLYN
®®XtremeTrim Inside Corner
WallSheathing
Lap Siding
Top Plate
XtremeTrim® Plank Inside Corner
FABRICATED STEEL
ITEM ID LENGTH
XIC
XICJ
XICS
10'
10'
10'
"A" "B"
7/8"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
2"
"A"
"B"
Stud
Inside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Inside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
Top Plate
WallSheathing
Weep Strip
3/8" beadof polyurethane
sealant
XtremeTrim® Plank Inside Corner
Lap Siding
SEALANT
TamlynWindow Tape
DESIGN FEATURE: Eliminates wood inside corner piece that will split/rot over time.
MATERIAL: Galvanized steel with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .019" ± .003
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
TamlynWrap™Drainable
House Wrap
TamlynWindow Tape
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
US Patent #5,960,598
21© 2013 TAMLYN www.tamlyn.com
®®XtremeTrim Panel Inside Corner
EXTRUDED ALUMINUM
Vertical Siding
Stud Top Plate
XtremeTrim® PanelInside Corner
Top Plate
WallSheathing
XtremeTrim®Panel Inside Corner
3/8" beadof polyurethane
sealant
Weep Strip
Vertical Siding
SEALANT
TamlynWindow Tape
DESIGN FEATURE: Design duplicates the look of a wood corner piece without the maintenance headaches. For use with 5/16" (8mm) panel products only.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
PRODUCT DETAIL:
AVAILABLE SIZES:
13/16"
1/2"
1/2"
ITEM ID LENGTH
XIC516 10'
Inside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Inside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
TamlynWindow Tape
TamlynWrap™Drainable
House Wrap
US Patent #5,960,598
PRODUCT DETAIL:
AVAILABLE SIZES:
22 www.tamlyn.com © 2013 TAMLYN
®®XtremeTrim Low Profile Panel Inside Corner
EXTRUDED ALUMINUM
Wall Sheathing
XtremeTrim®Low Profile PanelInside Corner
Vertical Siding
Top Plate
WallSheathing
3/8" beadof polyurethane
sealant
Weep Strip
Vertical Siding
TamlynWindow Tape
XtremeTrim®Low Profile PanelInside Corner
SEALANT
DESIGN FEATURE: Minimal face produces a clean, pleasing durable inside corner for vertical siding panels. For use with 5/16" (8mm) panel products only.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS: Stainless steel fasteners are recommended when installing XtremeTrim®. The nail application is in accordance to the siding manufactures best practice. A nail or two can be attached to hold trim in place while installing siding directly through trim and on to studs.
FASTENING: Do not fasten edges of panels until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite panel edges.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
1-1/2" 1/2"
Siding Size
ITEM ID LENGTH
XICLP516
SIDING SIZE
10'5/16" (8mm)
TamlynWindow Tape
TamlynWrap™Drainable
House Wrap
Inside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Inside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
PRODUCT DETAIL:
AVAILABLE SIZES:
23© 2013 TAMLYN www.tamlyn.com
®®XtremeTrim Low Profile Plank Inside Corner
EXTRUDED ALUMINUM
Wall Sheathing
XtremeTrim®Low Profile PlankInside Corner
Top Plate
WallSheathing
Weep Strip
DrainableHouse Wrap
3/8" beadof polyurethane
sealant
Lap Siding
SEALANT
XtremeTrim®Low Profile PlankInside Corner
DESIGN FEATURE: Minimal face produces a clean, pleasing durable inside corner with plank siding panels.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
ITEM ID LENGTH
XICLP34 10'
1.1"
3/8"
3/4"
TamlynWindow Tape
TamlynWindow Tape
Lap Siding
TamlynWrap™Drainable
House Wrap
Inside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Inside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
PRODUCT DETAIL:
AVAILABLE SIZES:
24 www.tamlyn.com © 2013 TAMLYN
®®XtremeTrim Low Profile Outside Corner
EXTRUDED ALUMINUM
"A"
Siding Size3/4" (XOCLP34)
ITEM ID "A"
XOCLP516
XOCLP716
XOCLP58
XOCLP34
SIDING SIZE
3/4"
3/4"
3/4"
1-1/2"
5/16" (8mm)
7/16" (11mm)
5/8" (16mm)
5/16" Lap Siding
3/4"1" (XOCLP34) Wall
Sheathing
Top Plate
XtremeTrim®Low ProfileOutside Corner
VerticalSiding
Stud
WallSheathing
Weep Strip
XtremeTrim® Siding H-Mold
Vertical Siding
3/8" beadof polyurethane
sealant
XtremeTrim® Low Profile Outside Corner
SEALANT
DESIGN FEATURE: Offers a clean outside corner with a minimum visual reveal for vertical siding panels or lap siding.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
TamlynWrap™Drainable
House Wrap
TamlynWindow Tape
Outside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
Outside Corner
TamlynWindow Tape
TamlynWrap™Drainable
House Wrap
25© 2013 TAMLYN www.tamlyn.com
®®XtremeTrim Reveal Outside Corner
EXTRUDED ALUMINUM
Stud
XtremeTrim®Reveal
Outside Corner
Wall SheathingStud
Vertical orLap Siding
WallSheathing
3/8" beadof polyurethane
sealant
XtremeTrim® Reveal Outside Corner
TamlynWindow Tape
SEALANT
Weep Strip
XtremeTrim® Vertical Reveal
Vertical Siding
PRODUCT DETAIL:
AVAILABLE SIZES:
ITEM ID "A"
XOCR516
XOCR716
XOCR58
XOCR34
SIDING SIZE
3/8"
3/8"
3/8"
3/4"
5/16" (8mm)
7/16" (11mm)
5/8" (16mm)
3/4" (19mm)
"A"
Siding Size
DESIGN FEATURE: Provides a clean, open outside corner which compliments the vertical reveal system.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
Outside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Outside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
TamlynWindow TapeTamlynWrap™
Drainable House Wrap
TamlynWrap™Drainable
House Wrap
26 www.tamlyn.com © 2013 TAMLYN
®®XtremeTrim Blunt Panel Outside Corner
ITEM ID LENGTH
XOCBL
PANEL SIZE
10'5/16" (8mm)
Wall Sheathing
Vertical Siding
XtremeTrim® BluntPanel Outside Corner
Stud
WallSheathing
3/8" beadof polyurethane
sealant
XtremeTrim® Blunt Panel Outside Corner
TamlynWindow Tape
Weep Strip
XtremeTrim® Siding H Mold
Vertical Siding
SEALANT
EXTRUDED ALUMINUM
PRODUCT DETAIL:
AVAILABLE SIZES:
1/2"
1-1/3"
7/8"
Siding Size
DESIGN FEATURE: Unique design creates an aesthetically attractive blunt corner look, for a strong durable outside corner with vertical siding panels.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
Outside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Outside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
TamlynWindow Tape
TamlynWrap™Drainable
House Wrap
11/16"
27© 2013 TAMLYN www.tamlyn.com
®XtremeTrim Butted Outside Corner
EXTRUDED ALUMINUM
Stud
WallSheathing
3/8" beadof polyurethane
sealant
XtremeTrim® Butted Outside Corner
TamlynWindow Tape
Weep Strip
XtremeTrim® Vertical Reveal
Vertical Siding
ITEM ID LENGTH
XOCBT 10'
Wall Sheathing
Vertical Siding or Lap Siding
XtremeTrim® Butted Outside Corner
SEALANT
PRODUCT DETAIL:
AVAILABLE SIZES:
3/4"
1"
1-1/2"
DESIGN FEATURE: A solid appearance and a versatile corner application with panel or plank or at transitions.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
Outside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Outside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
®
TamlynWrap™Drainable
House Wrap
TamlynWindow Tape
TamlynWrap™Drainable
House Wrap
Lap Siding
PRODUCT DETAIL:
AVAILABLE SIZES:
28 www.tamlyn.com © 2013 TAMLYN
®®XtremeTrim Transition Outside Corner
EXTRUDED ALUMINUM
Stud
WallSheathing
Weep Strip
XtremeTrim® Vertical Reveal
Vertical Siding
3/8" beadof polyurethane
sealant
XtremeTrim® Transition Outside Corner
SEALANT
ITEM ID LENGTH
XOCB51634 10'
3/8"
1-5/8"
5/16"
3/4"
1/2"
1-3/4"
Wall Sheathing
XtremeTrim® TransitionOutside Corner
Lap Siding
DESIGN FEATURE: Provides a smooth, rounded transition from vertical siding panels to lap siding.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
Outside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Outside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
Vertical Siding
TamlynWrap™Drainable
House Wrap
TamlynWindow Tape
TamlynWindow Tape
TamlynWrap™Drainable
House Wrap
Lap Siding
PRODUCT DETAIL:
AVAILABLE SIZES:
29© 2013 TAMLYN www.tamlyn.com
®®XtremeTrim Bullnose Inside Corner
EXTRUDED ALUMINUM
XtremeTrim®BullnoseInside Corner
ITEM ID LENGTH
XICB516
XICB34
10'
10'
Top Plate
WallSheathing
Weep Strip
3/8" beadof polyurethane
sealant
Vertical Siding
SIDING SIZE
1-5/16"1-1/4"
3/8"
1-1/2"
90°
Siding Size
5/16" (8mm)
3/4" (19mm)XtremeTrim®BullnoseInside Corner
SEALANT
DESIGN FEATURE: Provides a smooth, rounded inside corner for vertical siding panels and lap siding.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
Outside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Outside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
TamlynWindow Tape
TamlynWrap™Drainable
House Wrap
WallSheathing
TamlynWindow Tape
VerticalSiding
TamlynWrap™Drainable
House Wrap
PRODUCT DETAIL:
AVAILABLE SIZES:
30 www.tamlyn.com © 2013 TAMLYN
®®XtremeTrim Bullnose Outside Corner
EXTRUDED ALUMINUM
Wall Sheathing
Vertical Siding
Stud
WallSheathing
Weep Strip
XtremeTrim® Vertical Reveal
Vertical Siding
3/8" beadof polyurethane
sealant
XtremeTrim® Bullnose Outside Corner
SEALANT
ITEM ID LENGTH
XOCB516
XOCB34
10'
10'
SIDING SIZE
Siding Size
5/16" (8mm)
3/4" (19mm)
3/8"
1-1/2"
XtremeTrim® Bullnose Outside Corner
DESIGN FEATURE: Provides a smooth, rounded outside corner for vertical siding panels and lap siding.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
Outside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Outside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
TamlynWindow Tape
TamlynWindow Tape
TamlynWrap™Drainable
House Wrap
PRODUCT DETAIL:
AVAILABLE SIZES:
31© 2013 TAMLYN www.tamlyn.com
®®XtremeTrim 3-1/2" Outside Corner
EXTRUDED ALUMINUM
ITEM ID LENGTH
XOC35 10'
Wall Sheathing
Top PlateStud
XtremeTrim® Plank Outside Corner
3-1/2"
1/2"
3/4"
DESIGN FEATURE: A traditional outside corner without the joints, caulked seams and nail holes that butted 1x4s require.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply a continuous 3/8” bead of polyurethane sealant on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
Outside Corner
Window tape orbutyl flashing tapemin 2-1/2” overlap
Outside Corner
RECOMMENDED APPLICATION: If more than one length is required, refer to the following for overlapping instructions.
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
Lap SidingTamlyn
Window Tape
Stud
WallSheathing
3/8" beadof polyurethane
sealant
TamlynWindow Tape
Weep Strip
SEALANT
XtremeTrim® Plank Outside Corner
Lap Siding
TamlynWrap™Drainable
House Wrap
PRODUCT DETAIL:
AVAILABLE SIZES:
32 www.tamlyn.com © 2013 TAMLYN
®XtremeTrim Soffit Transition Trim
EXTRUDED ALUMINUM
ITEM ID LENGTH
XS516
FR716
8'
8'
1"
3/8"
93°
3°
3/8"
1.65"
1/2"
5/16"
5/16"
1/2"
XS516
FR716
Soffit
TamlynWrap™DrainableHouse Wrap
Wall Sheathing
VerticalSiding
Vertical Siding
XtremeTrim®Starter Strip
XtremeTrim®F Reveal
TamlynWrap™DrainableHouse Wrap
WallSheathing
SubfloorBottomPlate
Stud
Joist
TamlynWrap™DrainableHouse Wrap
Wall Sheathing
Vertical Siding
XtremeTrim®F Reveal
Soffit
Lap Siding
XtremeTrim®Starter Strip
TamlynWrap™DrainableHouse Wrap
WallSheathing
Soffit
Soffit
Vertical Siding
XtremeTrim®F Reveal
Weep Strip
TamlynWrap™DrainableHouse Wrap
Wall Sheathing
XtremeTrim® Vertical Reveal
3/8"
DESIGN FEATURE: Design for facade / soffit transition with an appearance complementary to the vertical reveal.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
®
33© 2013 TAMLYN www.tamlyn.com
WallSheathing
Stud
Bottom Plate
ConcreteFoundation
XtremeTrim®Starter Strip
LapSiding
WallSheathing
1"
.392"
®®XtremeTrim Starter Strip
93°
3°
EXTRUDED ALUMINUM
ITEM ID LENGTH
XS516 8'
3°
3/8"
WallSheathing
Stud
Bottom Plate
ConcreteFoundation
XtremeTrim®Starter Strip
VerticalSiding
XtremeTrim®Starter Strip
Stud
Lap Siding
PRODUCT DETAIL:
AVAILABLE SIZES:
DESIGN FEATURE: Starter/bottom course for both vertical and lap siding. Provides ease-of-installation with correct angle.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
WallSheathing
Vertical Siding
XtremeTrim® Transition Outside Corner
XtremeTrim®Starter Strip
TamlynWrap™Drainable
House Wrap
TamlynWindow Tape
®XtremeTrim Window Flashing
EXTRUDED ALUMINUM
Subfascia
Soffit
Vertical or Lap Siding
1/4" gap
Do not Caulk
Trim
XtremeTrim®Window Flashing
Shim Strips
XtremeTrim®Window Flashing
Trim
Lap Siding
ITEM ID LENGTH
XWF1148
XWF1128
XWF158
8'
8'
8'
DEPTH
1-1/4" (31.75mm)
1-1/2" (38.10mm)
1-5/8" (41.27mm)
TamlynWindow Tape
PRODUCT DETAIL:
AVAILABLE SIZES:
95°
45°
5/16"
1-3/4"
1/2"
Depth
DESIGN FEATURE: Provides an easy to install and long-lasting method of minimizing water penetration. Used over window trim, band boards, panel intersections, and other vertical surfaces.
MATERIAL: 6063 T-5 extruded aluminum alloy with proprietary coating that protects against harsh weather conditions and allows for paint adhesion.
THICKNESS: .050" (1.27mm) ± .005
FINISH: Available in standard primed (ready-to-paint), standard color match (available in most popular siding and soffit colors), Coastal Color Coating™, and anodized finishes. Unless otherwise specified all XtremeTrim® products are provided in primed.
FASTENERS AND FASTENING: Stainless steel fasteners are recommended when installing XtremeTrim® and fiber cement products. Panel/Plank nail application shall be in accordance with the siding manufacturers best practice. XtremeTrim® profiles may be secured in place with a few SS nails until fastened through panels and in to studs during panel fastening. Do not fasten edges of panels or planks until trims are in place. Fasten panel at center and work outward. Fasteners should be staggered on opposite edges of panels.
CUTTING: Use a non ferrous carbide miter saw blade when cutting XtremeTrim®.
PAINTING: Use Direct to Metal (DTM) paint with XtremeTrim®. See XtremeTrim® Painting Guide.
BUTT JOINTS: Polyurethane sealant is required between butt joints where two trims come together. May also be further protected by use of a piece of TAMLYN SecureSeal Tape behind the butt joint or with a metal flasher behind the joint.
RECOMMENDED APPLICATION: Apply waterproofing membrane on trim before setting panels to help minimize water intrusion behind the siding.
BEST PRACTICE FOR INSTALLING CORNERS Install house wrap - continuous from bottom to top, overlapping as per manufacturer's install method. Install 12" self adhesive membrane tape vertically at both inside and outside corners for additional protection against break down.
NOTES: Do not install XtremeTrim® Window Flashing on horizontal applications where the exterior flange can catch water.
Please follow siding manufacturer's best practice application when installing any Tamlyn accessory. XtremeTrim® profiles do not form a moisture management system, the architect and builder are responsible for designing and installing a code compliant building envelope.
WARNING: Before installing Tamlyn XtremeTrim® you must use either a drainable house wrap or a standard house wrap with rainscreen thus allowing moisture to weep between the siding and the house wrap. See drawings on page 5 for both the drainable housewrap and rainscreen methods.
34 www.tamlyn.com © 2013 TAMLYN
®
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable House Wrap
Tamlyn Window Tape
This profile may be specified as an arched product
XtremeTrim® ArchedWindow Flashing
TamlynWrap™Drainable
House Wrap
PRODUCT DETAIL:
AVAILABLE SIZES:
®® XtremeTrim Plank Flash / ProLine Plank Flash
US Patent #7,721,488
Weep Strip
FABRICATED ALUMINUM
ITEM ID LENGTH
PF5
PF6
PF7
PF8
PF9
PF12
SIDING SIZE
5-1/4"
6-1/4"
7-1/4"
8-1/4"
9-1/4"
12"
EPDM (Ethylene Propylene Diene Monomer): characteristics common to all closed-cell vinyl foam products include the ability to seal out air, moisture, light and dust.
5"
6"
7"
8"
9"
11-3/4"
ITEM ID LENGTH
PLPF6
PLPF7
PLPF8
SIDING SIZE
6-1/4"
7-1/4"
8-1/4"
6"
7"
8"
Length
1/4"6"
ProLine Plank Flash
EPDM
Finally a butt-joint flashing that really works!
Stud
WallSheathing
Lap Siding
XtremeTrim® Plank Flash
Weep Strip
35© 2013 TAMLYN www.tamlyn.com
PRODUCT DETAIL:
AVAILABLE SIZES:
Length
1/4"6"
DESIGN FEATURES: Use to reduce moisture penetration behind the joint where two planks butt together and drain water over the top edge of the last full course of siding. Pre-cut for quick and easy installation. Conveniently clips to your belt. Coating eliminates any reaction with fiber cement. Coating/paint means no reflective flashback as found using regular metal flashing. Stiff metal helps hold a tighter seal against the siding to not allow water pressure to enter and wick off to the sides, get past the plankflash and end up behind the siding. Better than using housewrap because housewrap is really intended as an air barrier not a flashing, and has limited uv exposure life. Roofing felt tends to weep and breakdown over time.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
THICKNESS: .019" ± .003
AVAILABLE COLOR: Navajo Beige
XtremeTrim® Plank Flash
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
THICKNESS: .012" ± .003
AVAILABLE COLORS: Available in Primed Arctic White or Light (Navajo Beige), Medium (Khaki Brown) and Dark (Iron Gray).
Stud WallSheathing
Lap Siding
ProLinePlank Flash
®® Snapvent Continuous Soffit Vent
DESIGN FEATURES: The best looking, most "framer-friendly", easy to install, effective continuous soffit vent on the market. Unique double leg channels hide edges of soffit material for clean look and help prevent vent from being pulled up into subfascia. Complies with the International Residential Code requiring that ventilation be balanced 50% exhaust / 50% intake (soffit) in all situations including continuous ridge vents. Patents cover use of Tamlyn H Mold at seams. 1/8" holes proven to not allow insects/ bugs/bees etc to enter the attic.
3" and 4" Snapvent® - 1/4", 5/16" and 5/8" Snapvent® is a must for large attic/steep pitched homes with limited soffit areas available to vent, and multifamily jobs, providing 12.7 and 18.8 sq.in/foot air flow (more attic ventilation = less likelihood of preventable problems such as mold, caused by excessive attic moisture), or use double vents.
MATERIAL: Extruded rigid PVC, industry-standard, durable, chemically resistant product designed for outdoor weatherability.
SV143 / SV51638 - Available in most popular Siding and Soffit colors. Specify color code using Color Palette on page 4.
WARNING: Use light or pastel paint colors only on Tamlyn PVC or Sherwin-Williams Vinyl Safe™ Paint. Use of dark color paint will cause deformation. Tamlyn vinyl products are not warranted if painted with dark color paint.
US Patents #5,799,446 / #5,937,592. US Trademark #2,170,997
3" Snapvent®
2-3/4"
1-7/8"
3/8"
Soffit Panel Size
2" Snapvent®
2-7/8"
3/8"
3-3/4"
Pre-trimmed upper legsallow for usage of same-size
vent/H Mold/soffit material for best look.
Soffit Panel
Snapvent®
Rafter
Ledger
Blocking
Soffit H-Mold
Subfascia
ITEM ID LENGTHPANEL SIZE
SV148
SV5168
SV388
SV7168
SV128
SV348
8'
8'
8'
8'
8'
8'
1/4" (6mm)
5/16" (8mm)
3/8" (9.52mm)
7/16" (11mm)
1/2" (12.7mm)
3/4" (19mm)
NFA*
9
9
9
9
9
9
*NFA = net free area / sq.in. per lineal ft.
36 www.tamlyn.com © 2013 TAMLYN
Rafter
Subfascia
Soffit PanelSnapvent®
Ledger
Fascia
Roof Sheathing
Frieze Board
Lap Siding
Shim Strip
Water ResistiveBarrier
WallSheathing
4" Snapvent®
4"
5"
EXTRUDED PVC
ITEM ID LENGTHPANEL SIZE
SV1438
SV51638
SV5838
8'
8'
8'
1/4" (6mm)
5/16" (8mm)
5/8" (16mm)
NFA*
12.7
12.7
12.7
3" SNAPVENT®
4" SNAPVENT®
ITEM ID LENGTHPANEL SIZE
SV1448
SV51648
8'
8'
1/4" (6mm)
5/16" (8mm)
NFA*
18.8
18.8
2" SNAPVENT®
3/8"
Soffit Panel Size
Soffit Panel Size
*NFA = net free area / sq.in. per lineal ft.
*NFA = net free area / sq.in. per lineal ft.
®® Ezvent Continuous Soffit Vent
US Patents #5,881,502 / #5,937,592. US Trademark #2,149,898
DESIGN FEATURES: The best looking, most "framer-friendly", easy to install, effective continuous soffit vent on the market. Unique double leg channels hide edges of soffit material for clean look and help prevent vent from being pulled up into subfascia. Patents cover use of Tamlyn H Mold at seams.
MATERIAL: Extruded rigid PVC, industry-standard, durable, chemically resistant product designed for outdoor weatherability.
WARNING: Use light or pastel paint colors only on Tamlyn PVC or Sherwin-Williams Vinyl Safe™ Paint. Use of dark color paint will cause deformation. Tamlyn vinyl products are not warranted if painted with dark color paint.
®
Hat Shaped Continuous Soffit Vent
DESIGN FEATURES: Tamlyn vinyl hat-shaped vents are available in 2", 3" and 4" widths to handle nearly any soffit ventilation needs. 3/8" depth works with all soffit thicknesses. Large perforated holes provide excellent intake airflow but inhibit pest entry. Wide Hat Shaped Vent is minimum acceptable for large homes and multi-family, or use double vents. Use Continuous Soffit Vent Connector Clip or Vinyl H Mold to join seams
MATERIAL: Extruded rigid PVC, industry-standard, durable, chemically resistant product designed for outdoor weatherability.
WARNING: Use light or pastel paint colors only on Tamlyn PVC or Sherwin-Williams Vinyl Safe™ Paint. Use of dark color paint will cause deformation. Tamlyn vinyl products are not warranted if painted with dark color paint.
1-7/8"
3/8"
2-7/8"
3/8"
2" Hat Shaped Vent
*NFA = net free area / sq.in. per lineal ft.
*NFA = net free area / sq.in. per lineal ft.
Pre-trimmed upper legs allow for usage of same-size vent/H Mold/soffit
material for best look.
Rafter
Subfascia
FasciaSoffitEzvent®
Frieze Board
Lap Siding
Shim Strip
Ledger
37© 2013 TAMLYN www.tamlyn.com
EXTRUDED PVC
EXTRUDED PVC
1-7/8"
3/8"
2-7/8"
SoffitPanel Size
ITEM ID LENGTHPANEL SIZE
EZV148
EZV5168
EZV7168
8'
8'
8'
1/4" (6mm)
5/16" (8mm)
7/16" (11mm)
NFA*
9
9
9
2" EZVENT®
ITEM ID LENGTHPANEL SIZE
EZV1448
EZV51648
8'
8'
1/4" (6mm)
5/16" (8mm)
NFA*
18.8
18.8
4" EZVENT®
Rafter
Subfascia
SoffitEzvent®
Ledger
Fascia
Frieze Board
Shim Strip
Lap Siding
Roof Sheathing
Water Resistive Barrier
WallSheathing
ITEM ID LENGTH
CUV8V 8'
NFA*
9
2" HAT SHAPED VENT
ITEM ID LENGTH
CUV8VW 8'
NFA*
12.7
3" HAT SHAPED VENT
ITEM ID LENGTH
CUV8V4 8'
NFA*
18.8
4" HAT SHAPED VENT
4"
5"
2-7/8"
3/8"
3/8"
3" Hat Shaped Vent
3-7/8"
4" Hat Shaped Vent3/8"
3/8"
Fascia
Soffit
Lap Siding
Shim Strip
Frieze Board
LedgerSubfascia
Hat ShapedVent
Rafter
4"
5"
3/8"
SoffitPanel Size
2" EZVENT® 4" EZVENT®
*NFA = net free area / sq.in. per lineal ft.
38 www.tamlyn.com © 2013 TAMLYN
®
Soffit H-Mold (Soffit Use Only)
1"
1/2"
Soffit Panel Size
DESIGN FEATURES: Covers the end seams of the soffit material and continuous vents, providing a more appealing appearance than simply butting the vents end to end.
MATERIAL: Extruded rigid PVC, industry-standard, durable, chemically resistant product designed for outdoor weatherability.
HM148 / HM5168 - Available in most popular Siding and Soffit colors. Specify color code using Color Palette on page 4.
WARNING: Use light or pastel paint colors only on Tamlyn PVC or Sherwin-Williams Vinyl Safe™ Paint. Use of dark color paint will cause deformation. Tamlyn vinyl products are not warranted if painted with dark color paint.
Rafter
Ledger
Blocking
Subfascia
Framing Member
ITEM ID LENGTHPANEL SIZE
HM148/12
HM5168/12
HM3812
HM71612
HM1212
HM5812
8' / 12'
8' / 12'
12'
12'
12'
12'
1/4" (6mm)
5/16" (8mm)
3/8" (9.52mm)
7/16" (11mm)
1/2" (12.7mm)
5/8" (16mm)
PVC Soffit H Mold
Soffit Panel
EXTRUDED PVC
Soffit Panel
®
Continuous Soffit Vent Connector Clip
DESIGN FEATURES: Join ends of vinyl continuous soffit vent pieces, creating a very clean look. Allows for expansion/ contraction of soffit material and/or continuous vents and eliminates gaps where pests can enter the attic.
MATERIAL: Extruded rigid PVC, industry-standard, durable, chemically resistant product designed for outdoor weatherability.
WARNING: Use light or pastel paint colors only on Tamlyn PVC or Sherwin-Williams Vinyl Safe™ Paint. Use of dark color paint will cause deformation. Tamlyn vinyl products are not warranted if painted with dark color paint.
ITEM ID LENGTH
CONNCLIP
CONNCLIP265
CONNCLIP4
1-13/16"
2.65"
4"
1-3/8"
Connector Clip
ContinuousSoffit Vent
ConnectorClip
Rafter
Ledger
Blocking
Soffit Panel
Subfascia
ContinuousSoffit Vent
EXTRUDED PVC
39© 2013 TAMLYN www.tamlyn.com
®
Weep Strip
DESIGN FEATURES: Designed to be installed at the base of vertical siding. The vents allow any moisture build up behind the siding panels to weep out while preventing pests from entering. The venting also provides cavity ventilation which assists in drying cavity moisture and also helps increase energy efficiency due to the separation between outside heat and interior walls.
MATERIAL: Extruded rigid PVC, industry-standard, durable, chemically resistant product designed for outdoor weatherability.
WARNING: Use light or pastel paint colors only on Tamlyn PVC or Sherwin-Williams Vinyl Safe™ Paint. Use of dark color paint will cause deformation. Tamlyn vinyl products are not warranted if painted with dark color paint.
ITEM ID LENGTH
VSJ38
VSJ34
8'
8'
®
Vent Strip
ConcreteFoundation
WallSheathing
Stud
Water ResistiveBarrier
1/2" expressed
joint
Bottom Plate
WallSheathing
Stud
SidingNail
ConcreteFoundation
PVC VentStrip
Water ResistiveBarrier
Vertical Siding
Rainscreen
2-3/4"
.71"
RainscreenSize
RAINSCREEN SIZE
3/8" (9.52mm)
3/4" (19mm)
EXTRUDED PVC
EXTRUDED PVC
Rainscreen
Vertical Siding
DESIGN FEATURES: Starter/bottom course for both lap siding and vertical siding. Perforated holes allow any moisture build up behind the siding panels to weep out while preventing pests from entering. The venting also provides cavity ventilation which assists in drying cavity moisture and also helps increase energy efficiency due to the separation between outside heat and interior walls.
MATERIAL: Extruded rigid PVC, industry-standard, durable, chemically resistant product designed for outdoor weatherability.
WARNING: Use light or pastel paint colors only on Tamlyn PVC or Sherwin-Williams Vinyl Safe™ Paint. Use of dark color paint will cause deformation. Tamlyn vinyl products are not warranted if painted with dark color paint.
WallSheathing
Stud
Bottom Plate
ConcreteFoundation
Weep Strip
VerticalSiding
Wall Sheathing
Stud
Bottom Plate
ConcreteFoundation
VerticalSiding
TamlynWrap™Drainable
House WrapWall
Sheathing
Window Tape
Weep Strip
XtremeTrim® Vertical Reveal
Vertical Siding
XtremeTrim® Bullnose Outside Corner
TamlynWrap™Drainable
House Wrap
TamlynWrap™Drainable
House Wrap2" 2"
3/4" 3/8"
3/8"3/8"Water Resistive
Barrier
Rainscreen
Rainscreen
ITEM ID LENGTH
VSZ38
VSZ34
8'
8'
RAINSCREEN SIZE
3/8" (9.52mm)
3/4" (19mm)
®
Counter Flashing
®
Reglet Flashing
DESIGN FEATURES: Designed to provide clearance between siding products and roofs, decks, paths, steps, driveways or any other solid surfaces.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular Siding and Soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
WallSheathing
2" Trim Piece
1/4" gapbetween flashing
and siding
Lap Siding
ExteriorSlab
Water Resistive Barrierlaps over 2" Trim Piece
Wall Sheathing
2" Trim Piece
Water Resistive Barrier laps over2" Trim Piece
Step Flashing
Roof Underlayment
Lap Siding
1/4" gap between flashing and siding
7/8”
2”
2TF - Specify Color #
1-5/8”
XtremeTrim®Starter Strip
F2TF - Specify Color #
4"
1"
CF4 - SpecifyColor #
XtremeTrim®Starter Strip
Custom sizes available to fit your specifications !
Custom sizes available to fit your specifications !
1”
95°
40 www.tamlyn.com © 2013 TAMLYN
US Patent #7,784,222
2”
2” 2”
95°
DESIGN FEATURES: Illustrated are examples of ways TAMLYN can produce appropriate reglet flash for your project. Based on the height of the wall to be flashed, the composition of the wall surface, and whether hidden or exposed fasteners are desired, the fabrication will be produced from first quality materials and is available pre-finished or ready to paint.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular Siding and Soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
"A"Specify
"B" Specify
"C" Specify
"A"Specify
"B" Specify
"C"Specify
"D"Specify
Screw
Reglet Flash
Flashing(look and size may differ)
Sealant
Sealant
Reglet Flash
RF - Specify Color #
135°
4”
1” 1”FTF4 -Specify Color#
®
Angle/Base Flashing
®
Step Flashing
Custom sizes available to fit your specifications !
Custom sizes available to fit your specifications !
41© 2013 TAMLYN www.tamlyn.com
DESIGN FEATURES: Efficient wall to roof application. Protects against leaks at walls and chimneys to roof connections.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
Wall Sheathing
Water Resistive Barrier laps over flashing
Angle Flashing
Roof Underlayment
Lap Siding
BF - Specify Color #
minimum 1 - 2"clearance from
high point of roofing
"B" Specify
90°
"A"Specify
XtremeTrim®Starter Strip
DESIGN FEATURES: Multiple uses including chimney and skylight flashing. Furnished in pre-cut, user friendly pieces; no need to spend valuable time cutting 10' flashing pieces to required shorter lengths.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
FS - Specify Color #
"A"
"B"
"C"
Wall Sheathing
Water Resistive Barrier laps over thestep flashing and the roofing felt
Step Flashing
Roof Underlayment
Lap Siding
minimum 1 - 2" clearance from high point of roofing
BFRH - Specify Color #
"B" Specify
90°
1/2" Hem
"A"Specify
BFHH - Specify Color #
"B" Specify
90°
1/2" Hem
"A"Specify
ITEM ID
FS448
FS6612
"A" "B" "C"
4"
6"
4"
6"
8"
12"
BFH - Specify Color #
"B" Specify
90°
1/2" Hem
"A"Specify
42 www.tamlyn.com © 2013 TAMLYN
®
Overhang Roof Edge
®
Angle Roof Edge
DESIGN FEATURES: Deflects water away from fascia board. Extended lip helps prevent shingle damage.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
Wall Sheathing
SoffitSubfascia
RoofSheathing
Roof DripEdge
Fascia
Vertical Siding
Rafter
Soffit
Wall Sheathing
Water ResistiveBarrier
SubfasciaFascia
RoofSheathing
Roof DripEdge
WaterResistiveBarrier
Vertical Siding
Custom sizes available to fit your specifications !
Wall Sheathing
SoffitSubfascia
RoofSheathing
Roof DripEdge
Fascia
Vertical Siding
Rafter
Soffit
Wall Sheathing
Water ResistiveBarrier
SubfasciaFascia
RoofSheathing
Roof DripEdge
Water ResistiveBarrier
Vertical Siding
3/16" Kick with Hem
On Roof
Face
DESIGN FEATURES: Deflects water away from fascia board. Extended lip helps prevent shingle damage.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
Over Hang
ITEM ID
DL145
DL1560
FACE ON ROOF
1"
1-1/2"
2-1/8"
3"
4-1/2"
6"
GIRTH
On Roof (min. 2")
1/2"
Face
ME Specify Color #
-
1/2"MG
Specify Color #-
ITEM ID
ME130
ME240
ME360
MG130
MG240
MG360
FACE
2"
2"
3"
2"
4"
3"
3"
4"
6"
3"
6"
6"
GIRTH
On Roof (min. 2")
Face
1"
2"
3"
1"
2"
3"
ON ROOF
DL Specify Color #
-
43© 2013 TAMLYN www.tamlyn.com
®
Fascia Cap Roof Edge
®
Gravel Stop Roof Edge
Custom sizes available to fit your specifications !
Custom sizes available to fit your specifications !
DESIGN FEATURES: Acceptable method of protection. All dimensions are variable based on job requirements, dimensions shown are minimums for those legs. For use with shingle or metal roofs.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
"A"Specify
1"
3-1/2"
3/8"
2"
DESIGN FEATURES: The correct edge that is to be installed at the conjunction of a wall surface and a flat or built-up roof deck. TAMLYN offers both a conventional ¾” knuckle for gravel roofs and a ¼” knuckle for modified roofing. We can adapt the face and deck dimensions to meet your job requirements, and available in either aluminum or pre-primed galvanized steel.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
"A"Specify
up to1-1/2"
3/8"
2"
"B" Specify
Fascia Cap
Roof FeltPaper
Appropriate fastenersfastened Approx. 6" on center
Gasketed fastenersfastened approx. 18" on center
Cleat
Gravel Stop
Roofing membrane
Appropriatefasteners fastenedapprox. 6" on center
Appropriate fasteners fastenedapprox. 3" on center staggered 1/2"
GS - Specify Color #
FC - Specify Color #
Hidden cleat: Preferred method of protection.All dimensions are variable based on job requirements
Shingles
Roof Sheathing
Roof Felt Paper
Fascia Cap
Gravel Stop
Roof Felt Paper
Roof Sheathing
44 www.tamlyn.com © 2013 TAMLYN
®
Window Flashing
®
Deck Ledger Flashing
DESIGN FEATURES: Protects against leaks at walls to deck intersection.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
WARNING: A layer of self-stick flexible material such as asphalt or butyl tape should always be used before installing aluminum or galvanized flashing on treated lumber. This prevents a chemical reaction between the flashing and copper azole in treated lumber.
Water ResistiveBarrier
"B" Specify
VWF - Specify Color #
"A"Specify
95°
Wall Sheathing
Custom sizes available to fit your specifications !
Custom sizes available to fit your specifications !
Lap Siding
Minimum 1 - 2"clearance fromhighest point of decking
DeckLedgerFlashing
Ledger
Deck Framing
XtremeTrim®Starter Strip
Requires Window Tape
Deck Ledger Flashing
Wall Sheathing
Lap Siding
Water Resistive Barrier
XtremeTrim® Starter Strip
Minimum 1 - 2" clearance from highest point of decking
Peel-and stick flashing
1/2" Hem
DESIGN FEATURES: Window flashing provides an easy to install and long-lasting method of stopping water penetration. Used over window trim, band boards, panel intersections, and other vertical surfaces.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
"A"Specify
"C"Specify
"B" Specify
VWF - Specify Color #
95°
Rafter
Subfascia
Soffit
Vertical Siding
Ledger
1/4" gap
Do not Caulk
Shim
Trim
Window Flashing
Lap Siding
Shim strips
Window Flashing
WaterResistiveBarrier
Trim
Window Tape
Water Resistive Barrier
ITEM ID
VWF348
VWF18
VWF1148
VWF1128
VWF158
VWF1W
VWF158W
"A" "B"
1-1/4"
1-1/2"
2-1/4"
2"
1-7/8"
4"
1-7/8"
3/4"
1"
1-1/4"
1-1/2"
1-5/8"
1"
1-5/8"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
"C"
120°
VWF158W
ITEM ID LENGTH
XIC
XICJ
XICS
10'
10'
10'
"A" "B"
7/8"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
2"
®
Outside Corner
DESIGN FEATURES: Patented design authentically duplicates the look of a wood corner piece without the maintenance headaches. Eliminates wood inside corner piece that will split/rot over time.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
Wall Sheathing
Water Resistive Barrier
Top Plate
Wall Sheathing
Inside Corner Lap SidingVertical Siding /
Inside Corner
WaterResistive Barrier
Custom sizes available to fit your specifications !
45© 2013 TAMLYN www.tamlyn.com
XIC, XICJ, XICS Specify Color #
Lap Siding
®
Inside Corner
Custom sizes available to fit your specifications ! US Patent #5,960,598
DESIGN FEATURES: Provides a good looking, durable outside corner with lap siding.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
1"
3-1/2"
3/4"
XOCBT4 - Specify Color #
Water ResistiveBarrier
Wall Sheathing
Top Plate
Vertical Siding orLap Siding
Butted Outside Corner
Wall Sheathing
Stud
Lap Siding
Water ResistiveBarrier
Butted Outside Corner
Vertical Siding
"A"
"B"
46 www.tamlyn.com © 2013 TAMLYN
®
Individual Outside Corner
®
Z Flashing
Custom sizes available to fit your specifications !
DESIGN FEATURES: Z Flashing provides an easy to install and long-lasting method of stopping water penetration. Used over window trim, band boards, panel intersections, and other vertical surfaces.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
"A"Specify
"B" Specify
VZB - Specify Color #
"C"Specify
95°
Roof Sheathing
Vertical Siding
Water Resistive Barrier
Wall Sheathing
SoffitSubfascia
Z Flashing
Water Resistive Barrier
Rafter
Subfascia
Soffit
Wall Sheathing
Vertical Siding
Ledger
Z Flashing
1/4" minimum gap
Decorative band board
DESIGN FEATURES: The traditional corner look that emulates hand fitted board junctions at the corners of siding plank walls. The individual corners create the “sawtooth” look that has a timeless appeal on Craftsman and other walls. Available in sizes for each common plank width and in both smooth and textured finishes to compliment the siding being used.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
ITEM ID LENGTH
OCI6
OCI7
OCI8
OCI9
OCI12
SIDING SIZE
5/16"
5/16"
5/16"
5/16"
5/16"
Length
6-1/4"
7-1/4"
8-1/4"
9-1/4"
12"
Siding Size
Stud
WallSheathing
TamlynWindow Tape
Lap Siding
TamlynWrap™Drainable
House Wrap
Weep Strip
IndividualOutside Corner
Water ResistiveBarrier
Wall Sheathing
Top Plate
IndividualOutside Corner
ITEM ID
VZB5168
VZB5168W
VZB388
VZB7168
VZB128
VZB588
"A" "B"
1-3/16"
4"
1-1/8"
1-1/16"
1"
1-3/8"
5/16"
5/16"
3/8"
7/16"
1/2"
5/8"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
"C"
47© 2013 TAMLYN www.tamlyn.com
®
J Flashing
Custom sizes available to fit your specifications !
®
Parapet/Coping Flashing
Custom sizes available to fit your specifications !
DESIGN FEATURES: Covers the top edge of siding at the soffit or intersections and at door and window openings. Isolates the edges of trim or siding from the mortar or masonry. Vertical use only in open areas. Can be used in horizontal areas where moisture and rain is not a factor.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
JMF - Specify Color #
"B" Specify"A" Specify
"C" Specify
Water Resistive Barrier
Wall Sheathing
Trim
J Flashing
Lap Siding
Brick LedgeFlashing
Do not caulkmin. 1/4" Gap
Ledger
Subfascia
Soffit
Vertical Siding
Water ResistiveBarrier
Wall Sheathing
J Flashing
XtremeTrim®Starter Strip
DESIGN FEATURES: Utilizing your own custom design, we will fabricate a coping flashing to cover and protect your parapet wall design from high grade aluminum or steel sheets. Whether you prefer a simple screw through or more complex, hidden fastener style, we are able to build what you require. The examples shown indicate styles commonly used.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
"A"Specify
1/2"
"B" Specify
Specify
Hidden cleat fastenedcoping/parapet cover:Preferred method of protection. All dimensions are variable based on job requirements
"C"Specify
Face fastened coping/parapet cover:Acceptable method of protection. All dimensionsare variable based on job requirements
Parapet/CopingFlash
Siding
Water ResistiveBarrier
Wall Sheathing
Membrane
Wood Framing
ITEM ID
JMF5168
JMF388
JMF128
JMF588
JMF348
JMF788
"A" "B" "C"
1-1/4"
1-5/8"
1-1/2"
1-3/8"
1-1/4"
2"
5/16"
3/8"
1/2"
5/8"
3/4"
7/8"
1/2"
1/2"
1/2"
1/2"
1/2"
1"
PCF - Specify Color #
48 www.tamlyn.com © 2013 TAMLYN
®
Horizontal Transition
®
Brick/Stone Ledger Flashing
Custom sizes available to fit your specifications !
Custom sizes available to fit your specifications !
90°
135°
.884"
2.03
3"
DESIGN FEATURES: Horizontal transition from vertical siding panels to lap siding.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
3"
135°
1-1/8"
1/2"
Water Resistive Barrier
Water Resistive Barrier
Rafter
Subfascia
Soffit
WallSheathing
Lap Siding
Ledger
HorizontalTransitionFlashing
BattenStrip
WallSheathing
Water Resistive Barrier
Lap Siding
Vertical Siding
BattenStrip
DESIGN FEATURES: Designed to prevent siding and trim to be butted directly against mortar or masonry, including stone and brick.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular Siding and Soffit colors. Specify color code using Color Palette on page 4.
8' Length Standard
"A"Specify
1/2" Hem
"B" Specify
BL - Specify Color #
120°
120°
WallSheathing
Stud
Bottom Plate
ConcreteFoundation
Lap Siding
WaterResistiveBarrier
Brick/StoneLedger Flashing
Brick, Stone orConcrete Block
Xtreme Trim™Starter Strip
Water Resistive Barrier
Wall Sheathing
Trim
J Flashing
Lap Siding
Do not caulkmin. 1/4" Gap
Xtreme Trim™Starter Strip
Brick/StoneLedgerFlashing
HBD54 - Specify Color #
INSTALLATION GUIDELINES Bending a doubled-over hem on the lengths up to 12 ft. Follow the brake edges of shapes will increase their manufacturer’s instructions for using the Aluminum expands when temperatures strength and help assure wave-free brake.r ise and contracts whenever edges.temperatures drop. Shapes, especially
longer ones, must be able to move CUTTING TRIM COILslightly. Failure to allow movement can Be sure that any joints are overlapped XtremeCoil can be cut with duckbill tin result in bulging or buckling when in the proper direction and by a snips or aviation shears for short or temperature changes significantly. sufficient amount to shed water. curved cuts. For longer straight cuts, it is
easiest to use a sharp heavy-duty utility Allow approximately 1/16” space Do not install coated aluminum trim knife to score the coil, then bend the coil between the ends of shapes and fixed coil in locations subject to standing back and forth on the score line until it objects, such as the walls of inside water for sustained periods of time. breaks. If you are using a portable brake, corners. position the coil in the brake and clamp it
down so that the brake’s jaws align with Do not place aluminum shapes in Nail shapes into place using painted corrosive environments or in direct where the cut is to be made. Score the aluminum or stainless steel trim nails. contact with corrosive materials. coil along the straight edge of the brake Drill oversized nail holes and do not nail jaw with the utility knife, then bend the too tightly. Nails should penetrate the coil back and forth on the score line until BENDING TRIM COILwood a minimum of 3/4.” the coil breaks.XtremeCoil can be used to make
custom aluminum trim shapes using a Never face nail fascia shapes. portable brake. Brakes are available in
49© 2013 TAMLYN www.tamlyn.com
®
XtremeCoil
Custom sizes available to fit your specifications !
®
Kick Out Flashing
DESIGN FEATURES:
XtremeCoil is designed for residential and light commercial applications. Trim coil can be field formed to provide low-maintenance coverings for exterior trim surfaces such as window and door casings, window sills, drip caps, fascias, porch posts, louvers, flashings, etc.
XtremeCoil is available in most popular James Hardie siding & trim colors and is available in a 24" x 50' roll. Also available in 4", 8", 12" and 24" x 8' flat stock.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
WARNING: Direct contact of aluminum Product(s) with certain dissimilar materials or contact with the water run-off from such materials is likely to result in corrosion, which is not covered by the Warranty.
J Flashing
Brick LedgeFlashing
WindowFlashing
DESIGN FEATURES: Kick out flashing is used where a lower roofline terminates against a vertical wall. The kick out is installed above the rain gutter or drip edge where the roof meets a vertical wall. It kicks out rain water and diverts it away from the lower wall.
MATERIAL: Aluminum sheet coated on both sides with paint system that is specifically formulated for residential exterior applications.
Available in most popular siding and soffit colors. Specify color code using Color Palette on page 4.
For use with 8/12 pitch or less.
Wall Sheathing
Water Resistive Barrier
Step Flashing
Lap Siding
Kick Out Flashing
Roof Underlayment
Shingles
Fascia board
KOFL (Left) Specify Color #
-
KOFR (Right) Specify Color #
-
50 www.tamlyn.com © 2013 TAMLYN
®
TamlynWrap™ Drainable House Wrap
®
Tamlyn Window Tape
DESIGN FEATURES: Tamlyn WindowTape is a self-adhering, self-sealing waterproofing tape designed for use around windows, doors, building seams and in general construction. It is composed of a white polymer film that is coated with an aggressive Broad Temperature Spectrum (BTS™) asphalt adhesive. A release liner protects the adhesive and is removed as the tape is installed.
The BTS™ adhesive self-seals around punctures such as nails and staples. This advanced system bonds to all common building and window materials and seals around fasteners to prevent damage caused by water penetration.
INTENDED USES: Install on the window sill to protect against moisture that can contribute to rot, mold and mildew. Use to seal the window flange to the building wall in new construction to prevent window leaks, seal around doors, under siding, exterior plaster, sill plates and wall joints, or in any application where the membrane is protected from long-term ultraviolet exposure.
AVAILABLE SIZES: Width 4", 6", 9" and 12", Length 75' and 100'
Installhorizontalstrip on sill
STEP 1 - Sill Flashing STEP 2 - Set Window
STEP 3 - Jamb Flashing STEP 4 - Head Flashing
Adherehorizontalstrip to headflange andsheathing.
Adhere verticalstrips to jambflanges andsheathing
Setwindowframe
DESIGN FEATURES: TamlynWrap™ Drainable House Wrap provides advanced moisture management. TamlynWrap™ minimize trapped moisture from an exterior wall and prevent the damaging effects of mold and rot. Provides faster cavity dry time from a wall versus standard housewraps. 1.5mm gap for better drainability.
ROLL SIZE: 5ft Width x 100' Length
EXCEEDS AC38, INCLUDING NEW DRAINAGE PROVISION
StudWall
Sheathing
TamlynWindow Tape
Weep Strip
XtremeTrim® Plank Outside Corner
Lap Siding
TamlynWrap™Drainable
House Wrap
USE R
OLL
ER T
O A
PPLY
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLY
USE R
OLL
ER T
O A
PPLY
TAMLY
N
USE R
OLL
ER T
O A
PPLY
TAMLY
N
USE R
OLL
ER T
O A
PPLYTAM
LYN
®®
USE R
OLL
ER T
O A
PPLY
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLY
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLY
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLYTAM
LYN
®®
USE R
OLL
ER T
O A
PPLY
TAMLY
N
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLY
TAMLY
NTAM
LYN
TAMLY
N
®®
USE R
OLL
ER T
O A
PPLY
"When Doing It Right Matters"
"When Doing It Right Matters"
DHW5
WS
51© 2013 TAMLYN www.tamlyn.com
®
Utility Moisture Flash
®
Tamlyn Color Sealant
Tamlyn Color Sealant is a high performance, one
component, permanently flexible, easy to use, multi-
purpose fast cure modified polyurethane sealant.
Tamlyn Color Sealant cures rapidly when exposed
to atmospheric moisture to form a durable bond.
Tamlyn Color Sealant Modified Polyurethane
Sealant is now available in 26 colors, all of which
match today’s popular window extrusions, and
siding colors, regardless of the material or
manufacturer.
FEATURES:- No Solvents, Very Low VOCs - AAMA Certified - Non-Yellowing- Can Be Painted in 2 hours - Fast Cure at a wide range of temperatures - Aggressive Adhesion to common construction
substrates - Compatible with SBS Flashing
APPLICATIONS - Perimeter sealing of windows, doors & skylights - Siding - Construction Flashing Applications - Sealing Water Proof Membrane - Industrial Applications
SPECIFICATIONS: ASTM C-920 Type S & TTS-
0230C, Grade NT, Class 25. AAMA 808.3-92
Exterior Perimeter Sealing.
HOW TO USE:
For best results, prepare clean, dry surface. Cut nozzle to desired bead size and puncture inner seal. Apply with a caulking gun forcing sealant onto the substrate, then tool if needed. Can be painted within 2 hours depending upon bead size. Clean excess material with mineral spirits or similar solvents. It is the user's responsibility to thoroughly test any proposed uses with any and/or all substrates.
PACKAGING:
10.1 fl oz plastic fixed nozzle cartridges
STORAGE LIFE:
10 months shelf life. Material is to be stored in a controlled environment below 75 degrees
LIMITED LIFETIME WARRANTY:
This product is guaranteed to give satisfactory performance if applied in accordance with the label directions. Liability to Tamlyn is limited to a full refund of the purchase price or product replacement if product is proven defective. Tamlyn shall not be liable for loss or damage, whether direct, consequential or incidental. There are no other warranties expressed or implied including the implied warranty of merchantability or fitness for a particular purpose.
COLOR SEALANTColors shown are as accurate as printing methods will permit. Please see actual product sample for true color. Product and color availability vary by region and are subject to change. There will be color variance lot to lot.
AW - Arctic White
AT - Autumn Tan
BB - Boothbay Blue
CHB - Chestnut Brown
CS - Cobble Stone
CR - Countrylane Red
HC - Harris Cream
HM - Heathered Moss
IG - Iron Gray
KB - Khaki Brown
MT - Monterey Taupe
MS - Mountain Sage
NB - Navajo Beige
PP - Parkside Pine
TB - Timber Bark
WB - Woodstock Brown
AW - Arctic White
AT - Autumn Tan
BB - Boothbay Blue
CHB - Chestnut Brown
CS - Cobble Stone
CR - Countrylane Red
HC - Harris Cream
HM - Heathered Moss
IG - Iron Gray
KB - Khaki Brown
MT - Monterey Taupe
MS - Mountain Sage
NB - Navajo Beige
PP - Parkside Pine
TB - Timber Bark
WB - Woodstock Brown
DESIGN FEATURES: Utility Moisture Flash is a heavy duty, flexible, tear resistant, woven polypropylene nail on flashing designed to prevent moisture and water from entering the wall cavity and when used around windows and doors. Utility Moisture Flash was engineered to provide excellent durability when exposed to high ultraviolet rays and has the ability to withstand high winds. The cross woven design is to be mechanically fastened with staples or capped nails. Easy to integrate with a weather-resistive barrier.
Approved for usage per ASTM E2112-01, Installation of Exterior Windows & Doors
Excellent Moisture Resistance - Up to 140 Hrs at 100% Humidity
Mold & Mildew Resistant
Wind & Tear Resistant
UV Resistant Up to 365 days
Fast & Flexible Installation
Resists Cracking
Will not De-laminate or Shrink
ROLL SIZE: 12" Width x 120' Length
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
TAMLYN
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
TAMLYN
®
WW
W.TA
MLYN
.COM
800-
334-
1676
UTI
LITY
MO
ISTU
RE F
LASH
ExteriorSheathing
Stud
Brick Ledge
UtilityMoisture Flash
TAM
LYN
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676 TA
MLY
N
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676 TA
MLY
N
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676 TA
MLY
N
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676 TA
MLY
N
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676 TA
MLY
N
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676 TA
MLY
N
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676 TA
MLY
N
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676 TA
MLY
N
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
TAM
LYN
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676 TA
MLY
N
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676 TA
MLY
N
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
®
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
TAM
LYN
WW
W.T
AM
LY
N.C
OM
800-3
34-1
676
PRODUCT OF
UTILITY MOIS
TURE FLASH
Brick Ledge
Exterior Sheathing(OSB/Insulation Board/HouseWrap)
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
WW
W.T
AM
LYN.C
OM
800-3
34-1
676TAM
LYN
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
N
®
WW
W.T
AM
LYN.C
OM
800-3
34-1
676
TAMLY
NTAM
LYN
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
NTAM
LYN
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
WW
W.TAMLY
N.C
OM 800-3
34-1
676 TAM
LYN
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
TAMLY
N
®
WW
W.TAMLY
N.C
OM 800-3
34-1
676
UtilityMoisture Flash
"When Doing It Right Matters"
"When Doing It Right Matters"
UMF
®
www.tamlyn.com
800-334-1676
EXCEEDS AC38, INCLUDING NEW DRAINAGE PROVISION
Advanced moisture management Minimize trapped moisture
Faster cavity dry time 1.5mm gap for better drain-ability
TamlynWrapDrainable House Wrap
TM
"When Doing It Right Matters"