1244 wall road broussard, la 70518 337-889-3203packer are anticipated and utilizes...
TRANSCRIPT
1244 Wall Road
Broussard , LA 70518
337-889-3203
WWW.EMINENTOILFIELDSERVICES.COM
Broussard, LA • Odessa, TX • El Campo, TX
Hobbs, NM • Jane Lew, WV
DOWNHOLE TOOLS
DOWNHOLE TOOLS
JS-2A Retrievable Casing Packer
The JS-2A Retrievable Casing Packer is a full-opening, set-down type hook-wall
and feature a large internal bypass that provides a free flow of fluids throughthe packer during running, retrieving, and circulating.
This packer is ideal for use when high differential pressures from below thepacker are anticipated and utilizes hydraulically-actuated button-type slips toanchor the packer against upward movement.
Setting the JS-2A is accomplished by rotating 1/3 right hand turn at the tool andsetting weight down. This one operation sets the slips, energizes the packingelements, and closes the bypass. Retrieval is accomplished by straight pick-up of the tubing or workstring that opens the bypass to equalize pressureabove and below the packer. Continued pick-up will retract the slips and allowthe packing elements to relax. The automatic ‘J’ system will engage and allowthe packer to be retrieved or moved downhole and be reset.
Specifications
Note: The most common sizes and specifications are depicted above. Other sizes are available upon request.
Internal Bypass
HydraulicHold Down
Slips
PackingElements
Slips
Drag Blocks
Casing Casing Max I.D. ThreadsO.D. Weight O.D. In. Box Up-Pin Down
4-1/2 9.5 - 13.5 3.77 1.812 2-3/8 EU 8RD
5.0 15.0 - 18.0 4.13 1.812 2-3/8 EU 8RD
5.0 11.5 - 15.0 4.25 1.812 2-3/8 EU 8RD
5-1/2 26.0 4.25 1.812 2-3/8 EU 8RD
5-1/2 20.0 - 23.0 4.51 1.938 2-3/8 EU 8RD
5-1/2 15.0 - 20.0 4.64 1.938 2-3/8 EU 8RD
5-1/2 13.0 - 15.5 4.78 1.938 2-3/8 EU 8RD
6-5/8 24.0 5.65 2.375 2-7/8 EU 8RD
7.0 38 5.65 2.375 2-7/8 EU 8RD
7.0 32.0 - 35.0 5.81 2.375 2-7/8 EU 8RD
7.0 26.0 - 29.0 5.97 2.375 2-7/8 EU 8RD
7.0 20.0 - 26.0 6.07 2.375 2-7/8 EU 8RD
7.0 17.0 - 20.0 6.27 2.375 2-7/8 EU 8RD
7-5/8 33.7 - 39.0 6.45 2.375 2-7/8 EU 8RD
7-5/8 24.0 - 29.7 6.67 2.375 2-7/8 EU 8RD
7-5/8 20.0 - 24.0 6.81 2.375 2-7/8 EU 8RD
8-5/8 57.4 - 60.7 6.98 3.000 3-1/2 EU 8RD
8-5/8 44.0 - 49.0 7.31 3.000 3-1/2 EU 8RD
8-5/8 32.0 - 40.0 7.53 3.000 3-1/2 EU 8RD
8-5/8 20.0 - 28.0 7.78 3.000 3-1/2 EU 8RD
9-5/8 47.0 - 53.5 8.21 3.000 3-1 /2 EU 8RD
9-5/8 40.0 - 57.0 8.44 3.000 3-1/2 EU 8RD
9-5/8 29.3 - 36.0 8.59 3.000 3-1/2 EU 8RD
10-3/4 40.5 - 55.5 9.50 3.000 3-1/2 EU 8RD
11-3/4 60.0 - 83.0 10.06 3.000 3-1/2 EU 8RD
11-3/4 38.0 - 65.0 10.38 3.000 3-1/2 EU 8RD
13-3/8 48.0 - 72.0 12.13 3.000 3-1/2 EU 8RD
16.0 75.0 - 102.0 14.50 3.750 3-1/2 EU 8RD
packer that is applicable for use in a variety of well treating, testing and tubingconveyed perforation operations. The packers have EU 8RD connections,
DOWNHOLE TOOLS
JS-3 Storm Packer
The JS-3 Storm Packer is a full-opening, set-down type hook-wallpacker that is applicable for use in a variety of well treating, testing, and stormpackers. The packers have drill pipe connections and feature a largeinternal bypass that provides a free flow of fluids through thepacker during running, retrieving, and circulating.
This packer is ideal for use when high differential pressures from below thepacker are anticipated and utilizes hydraulically-actuated button-type slips toanchor the packer against upward movement.
Setting the JS-3 is accomplished by rotating 1/3 right hand turn at the tool andsetting weight down. This one operation sets the slips, energizes the packingelements, and closes the bypass. Retrieval is accomplished by straight pick-up of the tubing or workstring that opens the bypass to equalize pressureabove and below the packer. Continued pick-up will retract the slips and allowthe packing elements to relax. The automatic ‘J’ system will engage and allowthe packer to be retrieved or moved downhole and be reset.
Specifications
Note: The most common sizes and specifications are depicted above.
Other sizes are available upon request.
Internal Bypass
HydraulicHold Down
Slips
PackingElements
Slips
Drag Blocks
7.0 38 5.65 2.25 2-7/8 IF
7.0 32.0 - 35.0 5.81 2.25 2-7/8 IF
7.0 26.0 - 29.0 5.97 2.25 2-7/8 IF
7.0 26.0 - 29.0 5.97 2.25 3-1/2 IF
7.0 20.0 - 26.0 6.07 2.25 2-7/8 IF
7.0 17.0 - 20.0 6.27 2.25 2-7/8 IF
7-5/8 33.7 - 39.0 6.45 2.25 2-7/8 IF
7-5/8 24.0 - 29.7 6.67 2.25 2-7/8 IF
7-5/8 20.0 - 24.0 6.81 2.25 2-7/8 IF
8-5/8 44.0 - 49.0 7.31 2.75 3-1/2 IF
8-5/8 32.0 - 40.0 7.53 2.75 3-1/2 IF
8-5/8 20.0 - 28.0 7.78 2.75 3-1/2 IF
9-5/8 47.0 - 53.5 8.21 2.75 3-1/2 IF
9-5/8 40.0 - 47.0 8.44 2.75 3-1/2 IF
9-5/8 29.3 - 36.0 8.59 2.75 3-1/2 IF
10-3/4 40.5 - 55.5 9.50 2.75 3-1/2 IF
10-3/4 40.5 - 55.5 9.50 2.75 4-1/2 IF
10-3/4 60.7 9.38 2.75 4-1/2 IF
11-3/4 60.0 - 83.0 10.06 2.75 3-1/2 IF
11-3/4 38.0 - 65.0 10.38 2.75 3-1/2 IF
13-3/8 48.0 - 72.0 12.13 2.75 3-1/2 IF
13-3/8 48.0 - 72.0 12.13 2.75 4-1/2 IF
16.0 75.0 - 102.0 14.50 3.75 4-1/2 IF
20.0 94.0 - 133.0 18.40 3.75 4-1/2 IF
Casing Casing Max I.D. ThreadsO.D. “ Weight # O.D. “ in. Box up-Pin Down
RUNNING:
1 On pipe rack or rig floor, make up Bottom Guide Sub and Top Crossover Sub (if needed) on packer using 36 and Cheater Pipe. Then make up storm valve in top of tool with 36 and cheater pipeon bottom sub of valve (Caution: Do not torque through any of the valve or packer internal connections. This connection will have to be made up with tongs when picked up).
2 Pick up and make up single joint of pipe in top of valve. Pick up storm packer assembly with elevators using joint of pipe as lift sub. Make up bottom connection of guide sub to drill pipe below packer with tongs. Make up guide sub to bottom sub of packer with tongs.
3 Pick up assembly with single joint and slack off to Top sub of packer and make up with tongs Storm valve to Packer and Drill pipe to Storm valve holding back up on top and rotating tight below rotary. (NOTE: DO NOT MAKE UP CONNECTIONS ABOVE PACKER ABOVE THE ROTARY AS THIS WILL OVER TIGHTEN STORM VALVE STINGER ASSEMBLY. MAKE UP AND BREAK STORM VALVE USING 36 SEVERAL TIMES TO TEST RELEASE MAXIMUM TORQUE 500 FT/LBS.)
4 Do not put slips on body of tool with weight of drill pipe hanging below (this will shift weight of drill pipe from mandrel to outer body and shear “J” mechanism).
5 Check tool to insure that it is not in set position. Turn 1/3 right-hand rotation and push up on drag block and slip assembly, and slips will engage cone. Release slip assembly and let it re-jay to bottom sub and attempt to push up; slips will not engage cone. Tool is ready to start in hole.
6 Run plug to setting depth (take precautions going through preventers and wellhead so plug will not hang up). Run real slow.
7 Care should be taken while running not to apply left torque to the drill pipe string before setting the Storm Packer. Once in position, the packer is ready to be set, Pick up the string approximately 1 foot. Set slip on drill pipe and use rotary to apply 1 to several turns to right depending on depth and deviation of well. If rig has Top Drive DO NOT SET SLIPS AND USE TOP DRIVE TO MAKE TURNS. Slack off on drill string until the packer starts taking weight. (usually takes about 1 foot ). Pick up on Drill pipe just enough to remove slips and Slack off the string weight onto the packer slowly.
8 To disconnect the Top sub from storm valve, pick up 1,000 to 3,000 lbs over string weight of drill pipe above the valve. Apply left hand torque to break the right hand acme thread and continue rotating to back out the Top Sub and close the valve. Approximately 14 round at valve.
9 Pull out of hole. If time and condition permit, the assembly may be pressure tested at this time to maximum of 1,000 psi differential pressure from the top. Too high a differential from above will cause the plug to shear out.
Stor m Packer
RUNNING & RETRIEVING INSTRUCTIONS FOR JS-3 PACKER & STORM VALVE AVAILABLE SIZES: 7”, 7 5/8”, 9 5/8”, 10 3/4”, 13 3/8”, 16”
RETRIEVING
1 Run the drill pipe back in with Storm Valve Top Sub on the bottom (use the proper size gauge ring for the casing size). Tag the valve and set approximately 1,000lbs. onto it. Be sure and have rig safety valve on top of drill pipe.
2 Turn drill pipe to right to re-engage drill pipe (turn with chain tongs or TOP DRIVE if equipped) while maintaining the weight on the valve. After drill pipe is made up with additional right-hand rotation, with 4 rounds of rotation, will move off seat to let pressure equalize. A total of 14 rounds will bottom out. (Do not use rotary). Place TIW valve on string and be prepared to handle pressure on drill pipe when opening equalizing sub.
3 To unseat packer. Pick up the weight of total string and ½ foot, the bypass will opened and be prepared to handle pressure on casing. Continue to pick up on the packer to release and packer will return to running position.
4 Pull out of hole slowly, especially when plug comes back through BOP stack.
VERY IMPORTANT FACTS WHEN RUNNING PACKER:
1 Tongs and back-up directly onto the immediate Box and Pin subs being tightened. Do not torque through any of the valve or packer internal connection.
2 Do not set slips around packer with drill pipe hanging below.
3 Make sure tool is not in set position before starting in hole. With tool hanging in rotary, pick up slip assembly and it should not come up on cone.
4 Run slowly through BOP stack and wellhead, making sure it will not hang-up. Bottom guide will help guide it through.
Stor m Packer
RUNNING & RETRIEVING INSTRUCTIONS FOR JS-3 PACKER & STORM VALVE AVAILABLE SIZES: 7”, 7 5/8”, 9 5/8”, 10 3/4”, 13 3/8”, 16”
SET-DOWN WEIGHT TABLE - JS-3 PACKERSMinimum rated load below packer after drill pipe is disconnected
7" - 8 5/8"...............................20,000#9 5/8" - 13 3/8”............... .......30,000#16" .........................................50,000# 20" .........................................60,000#
SET-DOWN WEIGHT TABLE - JS-3 PACKERS
Packing Element Temp. Limits Packer SizeSystem Hardness (Deg F) 7 & 7 5/8 8 5/890-70-90 0-300 9,000 11,00095-80-95 250-350 10,000 12,00080-70-80 0-200 8,000 10,000
Minimum Set Down Weight (in lbs.) Required To Pack-Off Packing Elements Systems While Drill pipe is connected
SET-DOWN WEIGHT TABLE - JS-3 PACKERS
Packing Element Temp.Limits Packer SizeSystem Hardness (Deg F) 9 5/8“ 10 3/4” 13 3/8” 16”
11 3/4”90-70-90 0- 300 15,000 18,000 20,000 25,000
Minimum Set-Down Weight (in lbs.) Required To Pack-Off Packing Elements Systems
7” & 7 5/8” .......................200,000#9 5/8”, 10 3/4”, 13 3/8......350,000#16”....................................500,000#Inquire for additional maximum loads
RATED MAXIMUM LOAD:
SERVICE TOOLS
SERVICE TOOLS
Model A Storm Valve
The Storm valve is a combination Back Pressure valve and Safety Joint that is run above a Storm Packer,in order to provide well control protection during a temporary abandonment of the well, without having topull the drill pipe or tubing. The Storm Valve allows the packers to be set and then permits disconnectionand retrieval of the drill pipe or tubing and the upper sub of the valve, while at the same time automaticallyclosing the Storm Valve, isolating the drill pipe below the Storm Packer.
Note:This Storm Valve is designed to be used with right hand set compression type packers only.
RunningThe Storm Valve is made up directly onto the top sub of the Storm Packer. The 4-1/2” I.F. connections areto be tightened with 22,800 ft-lbs. torque, (3-1/2” I.F. — 10,500 to 11,500 ft-lbs. torque)
Warning:Tongs and back-ups must be on the immediate Box and Pin Subs being tightened. Do not
torque through any of the valve or packer internal connections.
The two-start right acme connection (marker hand tight ) between the Top Sub and the Housing is to betightened at this time to about 500 ft-lbs. of torque (equivalent to 200 lb. man on 36” wrench). This is theconnection that will be broken and backed off downhole, so do not overtighten. Care should be takenwhile running not to apply left hand torque to the drill pipe string before setting the Storm Packer. Once inposition, the packer is ready to be set. Pick up the drill string approximately 1 foot.
Apply and hold right hand torque while moving back down with the drill string until the packer startstaking weight (usually 1 to 2 feet depending on the packer model). Slack off the string weight onto thepacker. To disconnect the Top Sub from the valve, pick up 1,000 to 3,000 lbs. over the string weight of the drill pipe above the valve. Apply left hand torque to break the two-start righthand acme thread and continue rotating to back out the Top Sub and close the valve. The drill pipe and Top Sub are retrieved and the B.O.P.’s closed. If time and conditions permit, the assembly may be pressure tested at this time to a maximum of 1,000 psi differential pressure fromthe top. Too high a differential from above will cause the Plug to shear out.
RetrievingRun the drill pipe back in with the Storm Valve Top Sub on the bottom (use the proper size Gauge Ringfor casing size). Tag the valve and set approximately 1,000 lbs. onto it and slowly rotate the pipe to theright while maintaining the weight on the valve. This will make up the acme thread and begin to openthe valve.
Warning:A valve should be installed on the string at surface before reconnection in case pressure has
built up in the pipe below the valve.
The valve will open before the Top Sub shoulders, but continue rotating until the pipe torques up. Donot attempt to unset the packer until any pressure in the drill string is under control.
To unset the Storm Packer, the drill pipe is picked up, opening the bypass in the packer. Before doingthis, insure the annulus is closed off at surface in case pressure has built up below the packer. After anypressure has been equalized, continue to pick up and pull out of the hole.
The Storm Valve incorporates an emergency pump-out plug which can be sheared out of the valve withdifferential pressure from above (it is not necessary for the Top Sub to be attached). The plug will shearout and move down the drill string.
Note:Once the plug is out, the valve cannot be closed.
Strength Specifications
• Body Tensile Load Rating Lbs. • Plug Shear out Differential Pressure with 8 BrassYield - 500,000 lbs. Screws: 2,200-2,700 psi total (approx. 300 psi/screw)Working - 250,000 lbs.
• Plug Shear out Differential Pressure with 8 Mild Steel• Pressure Rating psi Screws: 3,000-3,400 psi total (approx. 400 psi/screw)
(not considering Shear Out Plug)Yield - 16,000 psiWorking - 10,000 psi
SERVICE TOOLS
CS-1 Retrievable Casing Packer
The CS-1 Retrievable Casing Packer is a full-opening, set-down type hook-wall packer that is applicable for use in a variety of well treating, testing, andTubing Conveyed Perforating operations. The packers are available in 4-1/2”through 7-5/8” casing sizes and feature a large internal bypass that providesa free flow of fluids through the packer during running, retrieving, andcirculating. This packer is ideal for use when high differential pressures frombelow the packer are anticipated and utilizes hydraulically actuated buttontype slips to anchor the packer against upward movement.
Setting the CS-1 is accomplished by rotating 1/3 right hand turn at the tool andsetting weight down. This one operation sets the slips, energizes the packingelements, and closes the bypass. Retrieval is accomplished by straight pick-up of the tubing or workstring that opens the bypass to equalize pressureabove and below the packer. Continued pick-up will retract the slips and allowthe packing elements to relax.
Specifications
Note: Additional sizes available on request.
Casing Casing Tool Tool Threads OD Wt. OD ID Box up-Pin Down
4.50” 9.5 - 13.5 3.771 1.812 2-3/8 EU 8RD
4.50” 15.1 3.620 1.812 2-3/8 EU 8RD
5.00” 15 - 18 4.125 1.812 2-3/8 EU 8RD
5.00” 11.5-15 4.250 1.812 2-3/8 EU 8RD
5.50” 26 4.250 1.812 2-3/8 EU 8RD
5.50” 20 - 23 4.50 1.875 2-3/8 EU 8RD
5.50” 15.5 - 20 4.641 1.875 2-3/8 EU 8RD
5.50” 13 - 15.5 4.781 1.875 2-3/8 EU 8RD
6.625 12 6.078 2.375 2-3/8 EU 8RD
6.625 17 - 20 5.812 2.375 2-3/8 EU 8RD
6.625 24 5.656 2.375 2-3/8 EU 8RD
7.00” 38 5.656 2.375 2-7/8” EU 8RD
7.00” 32-35 5.812 2.375 2-7/8” EU 8RD
7.00” 26-29 5.968 2.375 2-7/8” EU 8RD
7.00” 20 - 26 6.078 2.375 2-7/8 EU 8RD
7.625” 33.7 - 39 6.453 2.375 2-7/8” EU 8RD
7.625” 24 - 29.7 6.672 2.375 2-7/8” EU 8RD
7.625” 20 - 24 6.812 2.375 2-7/8” EU 8RD
SERVICE TOOLS
2-3/8” - 20” Bridge Plug
The 2-3/8” through 20” are premium plugs designed to run on electric line.
Applications Used to isolate zones for temporary or permanent abandonment.
Product Features• Cost competitive• Constructed with drillable materials• Retaining rings to assist in preventing element extrusion• Top set with shear stud• No tension mandrel required• Rated at 300° F• Runs on existing electric line setting tool with most existing sleeves• Sets in P-110 casing
Specifications Guide
Casing T & C Plug O.D. Setting Range Set ForceO.D. Weight (lbs.) (in) (in) (lbs.)
min max
2-3/8” 4.0 - 5.8 1.750 1.780 2.074 9,000
2-7/8” 6.4 - 6.5 2.220 2.340 2.525 9,000
3-1/2” 5.75 - 10.3 2.750 2.867 3.258 9,000
3-1/2” 12.8 - 15.8 2.430 2.548 2.764 9,000
4” 5.6 - 14.0 3.140 3.340 3.732 20,000
4-1/2” 9.5 - 16.6 3.562 3.826 4.090 33,000
5” 11.5 - 20.8 3.937 4.154 4.560 33,000
5-1/2” 13.0 - 23.0 4.312 4.580 5.044 33,000
5-3/4” 14.0 - 25.2 4.699 4.890 5.290 33,000
6-5/8” 17.0 - 32.0 5.375 5.595 6.135 50,000
7” 17.0 - 35.0 5.687 6.000 6.538 50,000
7-5/8” 20.0 - 39.0 6.312 6.625 7.125 50,000
8-5/8” 24.0 - 49.0 7.125 7.310 8.097 50,000
9-5/8” 29.3 - 58.4 8.125 8.435 9.063 50,000
10-3/4” 32.7 - 60.7 9.437 9.660 10.192 50,000
11-3/4” 38.0 - 60.0 10.437 10.772 11.150 50,000
11-3/4” 60.0 - 83.0 9.937 10.192 10.772 50,000
13-3/8” 48.0 - 84.5 11.880 12.175 12.715 50,000
16” 65.0 - 118 14.125 14.576 15.250 50,000
20” 94.0 -133 18.375 18.730 19.124 50,000
SERVICE TOOLS
Wide Range Bridge Plug
The Wide Range Bridge Plug is a premium plug designed to run on electric line.
Applications Wide Range Bridge Plugs have small outside diameters that are designed torun through tubing or drill pipe with restricted internal diameters.
Product Features• Cost competitive• Runs through tubing nipples and other restrictions• Top set with shear stud• 10,000 psi rated at 350° F• Sets in P-110 Casing• Three piece element with rocker action back up rings• One piece slips
Specifications
Plug O.D. Setting Range Set Force Setting(in) Min Max (lbs.) Tool
1.468 1.610 1.995 8,000 1
1.906 2.156 2.50013,000
1, 2, 3
2.501 2.765 3
Note:1 = 1 1/2 Shorty2 = 1 11/16 Shorty with 6 3/8” Stroke3 = 1 11/16 Multi-Stage
Additional sizes available on request.
SERVICE TOOLS
Cement Retainer
The Cement Retainer is a modular designed drillable cement retainer.
Applications • Acidizing• Fracturing or cementing with a cement retainer
Product Features• Simple surface controlled valve• Allows pressure testing before squeeze• Valve automatically closes when the stinger
is removed locking in the squeeze pressure• Simple conversion to bridge plug• Mechanical or wireline set• Easily drilled
Specifications
Casing T & C Plug O.D. Setting Range Set ForceO.D. Weight (lbs.) (in) (in) (lbs.)
min max
2-3/8” 4.0 - 5.8 1.750 1.780 2.074 9,000
2-7/8” 6.4 - 6.5 2.220 2.340 2.525 9,000
3-1/2” 5.75 - 10.3 2.750 2.867 3.258 9,000
4” 5.6 - 14.0 3.140 3.340 3.732 20,000
4-1/2” 9.5 - 15.1 3.593 3.826 4.090 33,000
5” 11.5 - 20.8 3.937 4.156 4.560 33,000
5-1/2” 13.0 - 23.0 4.312 4.580 5.044 33,000
5-3/4” 14.0 - 25.2 4.700 4.890 5.290 33,000
6-5/8” 17.0 - 32.0 5.375 5.595 6.135 50,000
7” 17.0 - 35.0 5.688 6.004 6.538 50,000
7-5/8” 20.0 - 39.0 6.312 6.625 7.125 50,000
8-5/8” 24.0 - 49.0 7.125 7.511 8.097 50,000
9-5/8” 29.3 - 58.4 8.125 8.435 9.063 50,000
10-3/4” 32.7 - 60.7 9.437 9.660 10.192 50,000
11-3/4” 38.0 - 60.0 10.437 10.772 11.150 50,000
11-3/4” 60.0 - 83.0 9.937 10.192 10.772 50,000
13-3/8” 48.0 - 80.7 11.875 12.175 12.715 50,000
16” 65.0 - 118 14.125 14.576 15.250 50,000
20” 94.0 - 133 18.375 18.730 19.124 50,000
SERVICE TOOLS
Mechanical Setting Tool
The Mechanical Setting Tool is for setting drillable cement retainers and bridge plugs with pipe.
Applications• Setting cement retainers or bridge plugs on tubing or drill pipe
Product Features• Allows single run for squeeze work• Locked to cement retainer or bridge plug to avoid
premature setting or loss• Top slips partially covered to protect from accidental damage• Modular design• Will set other manufacturers’ cement retainer or bridge plugs• Drag spring design also available
SERVICE TOOLS
Snap-Out Seal Assembly
The “SOSA” is a tubing conveyed seal assembly used to operate thesliding valve of a cement retainer.
Applications • Acidizing• Fracturing or cementing with a cement retainer
Product Features• Same tool operates several sizes of retainers• Deters seals from pumping out of the retainer• Multiple safety release (rotate, snap-out)• Gives positive indication of stinger location
Setting ProcedureRun the “SOSA” to the setting depth of the Cement Retainer. Wash any debrisoff of the retainer. When the stinger enters the retainer bore, stop washing andset approximately 1,000 lbs. down on the retainer.
Retrieving ProcedureWhen the job is finished, the “SOSA” can also be released from the CementRetainer by pulling 5,000 to 8,000 lbs. of tension.
The “SOSA” can also be released from the retainer by rotating 8 to 10 turns tothe right at the tool while pulling 1,000 to 2,000 lbs. of tension.
SERVICE TOOLS
Tubing Tester
The Tubing Tester is a full open tool which is used to pressure test the tubingfor leaks. The tubing tester is designed to run with any of our set-down typepackers which are compatible.
The tubing tester has a maximum pressure differential of 10,000 PSI but otherfactors should be taken into consideration regarding pressures, such as theother tools run with the tester and the tubing strength.
OperationRun the tubing tester in on tubing above the Packer or any other tool which iscompatible. The tubing tester is run in with the flapper in the open position. Theflapper is closed to test the tubing. This is done by rotating the tubing 1-1/2turns to the right at the tool and pick up. After testing is complete, the tester islocked open by straight set down weight.
Note: When pulling high tension on the tester, the tester should be left in thetest position.
Specifications
Nominal Max. O.D. Min. I.D. Standard ThreadTubing of Tool of Tool ConnectionSize (in) (in) (in)
2-3/8” 3.750 1.88 2.375” EU 8RD
2-7/8” 5.250 2.38 2.875” EU 8RD
Note:Additional sizes available on request.
SERVICE TOOLS
“K” Valve
DescriptionThe “K” Valve is a high pressure valve that converts a retrievable packer intoa bridge plug.
ApplicationsUsed with neutral set packers to create a temporary bridge plug for acidizing,fracturing, cementing, casing pressure tests, well head replacement and zoneisolation.
Features• Balanced equalizing system• Large bypass area minimizes plugging by debris• Bonded seals allow repeated opening• Open during running or pulling• Strong jay pins are not threaded to the fishing neck• Retrieving head is auto-on jay, left hand release• Full bore retrieving head permits through tubing perforating• Bypass valve can be opened and closed without releasing the packer• Locked to retrieving head while running or pulling
RETRIEVABLE PACKERS
R E T R I E VA B L E PA C K E R S
AS1-X Retrievable Production Packer
The AS1-X Retrievable Production Packer effectively meets severalrequirements for zone isolation, injection, pumping and production. Fullopening gives unrestricted flow and allows the passage of wireline tools andother accessories. A mechanical lock-set action holds substantial pressuresfrom above or below the packer, whether the packer is left in tension,compression or neutral. A large internal bypass reduces the swabbing effectwhen running or retrieving. The bypass closes upon setting the packer. Whenreleasing, the bypass opens first to equalize pressures before releasing theupper slips. The AS1-X Retrievable Production Packer has a rotationalsafety release feature, or an optional adjustable straight pull shear safetyrelease.
The AS1-X Retrievable Production Packer can be set by compression or with tension, thus making it ideal for shallow wells requiring the use offiberglass tubing.
Product Features• Available with Ecner Array• Patented releasing slip system• Bypass Valve below upper slips so the debris is washed
from slips when valve is opened• Bypass valve opens before hold down is released• Can be set with tension for use in shallow wells• No tension or compression required to hold tool in place after set• 1/4 turn right-hand set, right-hand release• Safety release (optional)
(see specification chart on next page)
AS1-X 10K packer incorporates all the features of AS1-X, with the ability towithstand differential pressure of 10,000 psi from above or below. AS1-X 10Kis not available in sizes larger than 7-5/8”.
AS1-X HP packer incorporates all the features of AS1-X, with the ability towithstand differential pressure of 7,500 psi from above or below. AS1-X Hpis not available in sizes larger than 9-5/8”.
R E T R I E VA B L E PA C K E R S
Specifications (2-7/8” - 13-7/8”)
Casing Weight O.D. of Nominal Packer StandardSize Tool Casing I.D. Bore Thread
Range ConnectionMin. Max.
2-7/8” 6.4 - 6.5 2.250 2.376 2.441 0.625 0.750 EU 10RD
3-1/2” 7.7 - 10.2 2.781 2.922 3.068 1.250 1.500 EU 10RD
4” 9.5 - 11.0 3.250 3.476 3.548 1.500 1.500 NU 10RD
4-1/2” 15.1 - 16.6 3.594 3.754 3.826 1.500 1.900 NU 10R13.5 - 15.1 3.680 3.826 3.920 1.938 2.375 EU 8RD9.5 - 13.5 3.750 3.920 4.090 1.938 2.375 EU 8RD
5” 18.0 - 20.8 4.000 4.156 4.276 1.938 2.375 EU 8RD11.5 - 15.0 4.125 4.408 4.560 1.938 2.375 EU 8RD
5-1/2” 20.0 - 23.0 4.500 4.670 4.778 1.938 3.375 EU 8RD13.0 - 17.0 4.625 4.892 5.044 1.938 2.375 EU 8RD20.0 - 23.0 4.500 4.670 4.778 2.375 2.875 EU 8RD15.5 - 20.0 4.625 4.778 4.950 2.375 2.875 EU 8RD13.0 - 14.0 4.813 5.012 5.044 2.375 2.875 EU 8RD
6” 15.0 - 20.0 5.188 5.352 5.524 2.375 2.875 EU 8RD
6-5/8” 24.0 - 32.0 5.500 5.675 5.921 2.500 2.875 EU 8RD20.0 - 24.0 5.750 5.921 6.049 3.000 3.500 EU 8RD17.0 - 24.0 5.750 5.921 6.135 2.500 2.875 EU 8RD
7” 29.0 - 35.0 5.812 6.004 6.184 2.500 2.875 EU 8RD17.0 - 26.0 6.000 6.276 6.538 2.500 2.875 EU 8RD26.0 - 32.0 5.875 6.004 6.276 3.000 3.500 EU 8RD17.0 - 26.0 6.000 6.276 6.538 3.000 3.500 EU 8RD
7-5/8” 39.0 - 45.3 6.250 6.435 6.625 2.500 2.875 EU 8RD33.7 - 39.0 6.453 6.625 6.765 2.500 2.875 EU 8RD24.0 - 29.7 6.672 6.875 7.025 2.500 2.875 EU 8RD
8-5/8” 32.0 - 40.0 7.500 7.725 7.921 4.000 4.500 EU 8RD24.0 - 28.0 7.750 8.017 8.097 4.000 4.500 EU 8RD
9-5/8” 43.5 - 53.5 8.250 8.535 8.755 4.000 4.500 EU 8RD32.0 - 32.6 8.500 8.755 9.001 4.000 4.500 EU 8RD
10-3/4” 51 - 65.7 9.312 9.560 9.850 4.00 4.500 EU 8RD32.75 - 45.5 9.700 9.950 10.192 4.00 4.500 EU 8RD
4.500 EU 8RD48 - 72 12.000 12.347 4.0013-3/8” 12.716
Note:Additional sizes available on request.
AS1-X Retrievable Production Packer
RETRIEVABLE PACKERS
AS1-XW Retrievable Production Packer
The AS1-XW Packer is a full opening, retrievable production packer thatperforms like a permanent packer without the expense of seal units. Run withan on/off tool the AS1-XW can be set on wireline and retrieved on tubing.Unlike other wireline set retrievable packers that require seal units and aseparate retrieving tool, the AS1-XW can be pulled from the well without extratubing runs. Once the packer has been retrieved it can be redressed and runagain on wireline or tubing. The AS1-XW is one of the most economicalwireline set retrievable packers on the market today.
Product Features• Packer can be set on wireline or tubing• No need for expensive seal units• Packer can be run under pressure with plugging device• Bypass opens before slips are released
Specifications
Casing O.D. Casing WT. Max O.D. Connection
4-1/2” 15.1 - 16.6 3.594 1.900 EU 8RD
4-1/2” 9.5 - 13.5 3.750 2.375 EU 8RD
5” 18.0 - 21.0 4.000 2.375 EU 8RD
5” 11.5 - 15.0 4.125 2.375 EU 8RD
5-1/2” 13.0 - 20.0 4.625 2.375 EU 8RD
5-1/2” 20.0 - 23.0 4.500 2.375 EU 8RD
5-1/2” 15.5 - 17.0 4.625 2.875 EU 8RD
5-1/2” 20.0 - 23.0 4.500 2.875 EU 8RD
7” 26.0 - 32.0 5.875 2.875 EU 8RD
7” 17.0 - 26.0 6.000 2.875 EU 8RD
7-5/8” 33.7 - 39.0 6.453 2.875 EU 8RD
7-5/8” 24.0 - 29.7 6.672 2.875 EU 8RD
8-5/8” 44.0 - 49.0 7.312 2.875 EU 8RD
Note: Additional sizes available on request.
4.500 EU 8RD9-5/8” 43.5 - 53.5 8.250
9-5/8” 32.3 - 43.5 8.500 4.500 EU 8RD
10-3/4 32.75 - 45.5 9.700 4.500 EU 8RD
9.312 4.500 EU 8RD10-3/4” 51-65.7
R E T R I E VA B L E PA C K E R S
“R-3” Double & Single Grip Packer
DescriptionThe “R-3” is a double grip, compression set, retrievable packer.
Applications• Most production, stimulation and testing operations
Features• Differential lock helps keep the by-pass closed and locked to the
mandrel during high pressure operations• Automatically returns to run in position when moved up the hole• Hydraulic hold-down for differential pressure from below• Long stroke mandrel simplifies circulation of fluids without
releasing the packer• Large by-pass allows speedy equalization of fluids• Rocker type slips• Parts interchangeable with other manufacturers• Standard Right Hand Set, optional left hand set
Specifications
Casing Packer
O.D. Wt. Min. Max. Max. StandardO.D. Box x PIN
4-1/2” 9.5 - 13.5 3.910 4.090 3.771 2-3/8” EU 8RD
5” 15 - 18 4.250 4.408 4.125 2-3/8” EU 8RD11.5 - 15 4.408 4.560 4.250 2-3/8” EU 8RD
5-1/2” 26 4.408 4.560 4.250 2-3/8” EU 8RD20 - 23 4.625 4.778 4.500 2-3/8” EU 8RD
15.5 - 20 4.778 4.950 4.641 2-3/8” EU 8RD13 - 15.5 4.950 5.190 4.781 2-3/8” EU 8RD
5-3/4” 22.5 4.950 5.190 4.781 2-3/8” EU 8RD
6” 26 4.950 5.190 4.781 2-3/8” EU 8RD20 - 23 5.191 5.390 5.062 2-3/8” EU 8RD15 - 18 5.391 5.560 5.156 2-3/8” EU 8RD
6-5/8” 34 5.561 5.609 5.406 2-3/8” EU 8RD28 - 32 5.610 5.291 5.484 2-3/8” EU 8RD24 - 28 5.992 5.921 5.781 2-3/8” EU 8RD
24 5.830 5.937 5.656 2-7/8” EU 8RD17 - 20 5.938 6.135 5.812 2-7/8” EU 8RD
7” 38 5.830 5.937 5.656 2-7/8” EU 8RD32 - 35 5.938 6.135 5.812 2-7/8” EU 8RD26 - 29 6.136 6.276 5.968 2-7/8” EU 8RD20 - 26 6.276 6.456 6.078 2-7/8” EU 8RD17 - 20 6.456 6.578 6.266 2-7/8” EU 8RD
7-5/8” 33.7 - 39 6.579 6.797 6.453 2-7/8” EU 8RD24 - 29.7 6.798 7.025 6.672 2-7/8” EU 8RD20 - 24 7.025 7.125 6.812 2-7/8” EU 8RD
8-5/8” 44 - 49 7.511 7.687 7.312 3-1/2” EU 8RD32 -40 7.688 7.921 7.531 3-1/2” EU 8RD20 - 28 7.922 8.191 7.781 3-1/2” EU 8RD
9-5/8” 47 - 53.5 8.343 8.681 8.218 3-1/2” EU 8RD40 - 47 8.681 8.835 8.437 3-1/2” EU 8RD
29.3 - 36 8.836 9.063 8.593 3-1/2” EU 8RD
Note:Additional sizes available on request.
R E T R I E VA B L E PA C K E R S
Large Bore “R-3” Double and Single Grip Packer
DescriptionThe Large Bore “R-3” is a double grip, compression set, retrievable packer.
Applications• Most production, stimulation and testing operations
Features• Differential lock helps keep the by-pass closed and locked
to the mandrel during high pressure operations• Automatically returns to run in position when moved up the hole• Hydraulic hold-down for differential pressure from below• Long stroke mandrel simplifies circulation of fluids without
releasing the packer• Large by-pass allows speedy equalization of fluids• Rocker type slips• Parts interchangeable with other manufacturers• Large bore
Specifications
Casing Packer
O.D. Wt. Min. Max. Size Max. StandardO.D. Box x PIN
5-1/2” 20 - 23 4.625 4.777 5-1/2 x 2.38 4.500 2-7/8” EU 8RD17 - 20 4.778 4.892 5-1/2 x 2.38 4.641 2-7/8” EU 8RD
13 - 15.5 4.950 5.190 5-1/2 x 2.38 4.781 2-7/8” EU 8RD
5-3/4” 22.5 4.893 5.044 5-3/4 x 2.38 4.781 2-7/8” EU 8RD
6” 26 4.893 5.044 6 x 2.38 4.781 2-7/8” EU 8RD
6-5/8” 20 5.989 6.094 6-5/8 x 3.00 5.812 3-1/2” EU 8RD17 6.136 6.276 6-5/8 x 3.00 5.968 3-1/2” EU 8RD
7” 32 - 35 5.989 6.094 7 x 3.00 5.812 3-1/2” EU 8RD26 - 29 6.136 6.276 7 x 3.00 5.968 3-1/2” EU 8RD20 - 26 6.276 6.456 7 x 3.00 6.078 3-1/2” EU 8RD17 - 20 6.456 6.578 7 x 3.00 6.266 3-1/2” EU 8RD
7-5/8” 33.7 - 39 6.579 6.765 7-5/8 x 3.00 6.453 3-1/2” EU 8RD24 - 29.7 6.766 7.025 7-5/8 x 3.00 6.672 3-1/2” EU 8RD20 - 24 7.025 7.125 7-5/8 x 3.00 6.812 3-1/2” EU 8RD
Note: Additional sizes available on request.
RETRIEVABLE PACKERS
Specifications
Casing Packer
O.D. Wt. Min. Max. Max. StandardO.D. Box x PIN
4-1/2” 11.6 - 13.5 3.910 4.00 3.771 2-3/8” EU 8RD9.5 - 10.5 4.001 4.090 3.771 2-3/8” EU 8RD
5” 15 - 18 4.250 4.408 4.125 2-3/8” EU 8RD11.5 - 15 4.408 4.560 4.250 2-3/8” EU 8RD
5-1/2” 26 4.408 4.560 4.250 2-3/8” EU 8RD20 - 23 4.625 4.778 4.500 2-3/8” EU 8RD
15.5 - 20 4.778 4.950 4.641 2-3/8” EU 8RD13 - 15.5 4.950 5.190 4.781 2-3/8” EU 8RD
6” 26 4.950 5.190 4.781 2-3/8” EU 8RD20 - 23 5.191 5.390 5.062 2-3/8” EU 8RD15 - 18 5.391 5.560 5.156 2-3/8” EU 8RD
6-5/8” 34 5.561 5.609 5.406 2-3/8” EU 8RD24 - 32 5.610 5.921 5.484 2-3/8” EU 8RD17 - 24 5.922 6.135 5.781 2-3/8” EU 8RD
24 5.830 5.937 5.656 2-7/8” EU 8RD17 - 20 5.938 6.135 5.812 2-7/8” EU 8RD
7” 38 5.830 5.937 5.656 2-7/8” EU 8RD32 - 35 5.938 6.135 5.812 2-7/8” EU 8RD26 - 29 6.136 6.276 5.968 2-7/8” EU 8RD23 - 26 6.276 6.366 6.078 2-7/8” EU 8RD17 - 20 6.456 6.578 6.266 2-7/8” EU 8RD
7-5/8” 33.7 - 39 6.579 6.797 6.453 2-7/8” EU 8RD24 - 29.7 6.798 7.025 6.672 2-7/8” EU 8RD20 - 24 7.025 7.125 6.812 2-7/8” EU 8RD
8-5/8” 44 - 49 7.511 7.687 7.312 3-1/2” EU 8RD32 -40 7.688 7.921 7.531 3-1/2” EU 8RD20 - 28 7.922 8.191 7.781 3-1/2” EU 8RD
9-5/8” 47 - 53.5 8.343 8.681 8.218 3-1/2” EU 8RD40 - 47 8.681 8.835 8.437 3-1/2” EU 8RD
29.3 - 36 8.836 9.063 8.593 3-1/2” EU 8RD
Lok-Set Packer
DescriptionThe Lok-Set is a compression set, retrievable packer that allows thetubing to be left in a tension, compression, or neutral condition.
Applications• Most production, injection and zone isolation operations.
Features• Internal by-pass• Opposed dovetail slips for positive set• Holds pressure from above or below• Can leave tubing in a tension, compression, or neutral condition• Right hand rotation sets and releases the packer• Retracted dovetail slips• Converts to mechanical bridge plug with the addition of a valve• Parts interchangeable with other manufacturers• Optional packing element systems
R E T R I E VA B L E PA C K E R S
“FH” Hydrostatic/Hydraulic Packer
The “FH” is a Hydrostatic and/or Hydraulic Set Packer that allows the tubingto be left in a compression or neutral condition.
Applications• Multi-zone production in crooked or deviated holes not suitable for
mechanical packers• Installations where the wellhead is flanged up before the packer is set
Features• No tubing manipulation required• Withstands high hydrostatic pressures• Hydraulic set for low hydrostatic head wells• Locked in pack-off force• No mandrel movement during setting• Straight pull or optional rotational release• Hydraulic hold-down for differential pressure from below• Parts interchangeable with other manufacturers
Setting ProcedureThe “FH” Hydrostatic/Hydraulic Packer is set by pressuring the tubing to obtaina differential at the packer. To accomplish this, a means of temporarilyplugging the tubing below the packer must be provided.
Releasing ProcedureThe standard “FH” is a Hydrostatic and/or Hydraulic Set Packer and isequipped with 30,000 lbs. shear ring for a straight upstrain release. Othervalues of shear rings are available (20,000 to 40,000 lbs. for size 4-1/2” and20,000 to 50,000 lbs. for all sizes 5-1/2” thru 9-5/8”).
(see specification chart on back)
RETRIEVABLE PACKERS
Hydrow II Dual String Packer
The Hydrow II is a hydraulic set, mechanically held dual string productionpacker which is normally run above a single hydraulic set or wireline set sealbore packer. The short length of the Hydrow II makes it ideally suited fordeviated wells or doglegs. Also, since there is no tubing manipulation requiredto set the packer, the well head can be installed and flanged up before settingthe packer.
The Hydrow II is available with short or long string setting capabilities and avariety of tubing connections. The packer has been carefully designed formaximum flexibility when it comes to submersible pump applications. Bychanging only a few parts, the Hydrow II can be modified from a high pressureproduction packer to a packer installation for submersible pump.
The Hydrow II has a patented sequential upper slip releasing system that isdesigned so that each slip is released individually to reduce the pull requiredto release the packer. The angles on the penetration of the slip body result insmooth release from the casing.
The Hydrow II has several seal options for the short string. J-Latch or colletlatch tops are available with various types of seal assemblies.
Product Features• Short, compact, and economical• No hydraulic hold down buttons• Shear release easily adjusted• Heavily loaded slip system for easy release• Sequential upper slip on low pressure side of
the critical O-rings after setting• Hydraulic set to allow flanging-up before setting packer• Differential pressure helps to improve rubber pack-off
Specifications
Casing Casing I.D. Max O.D. Long String Short StringRange I.D. (in.) of Tool
Thread Mandrel Thread Stringer Seal BoreO.D. Wt. Min. Max. Connection I.D. Connection
Box Up/Pin Down Box Up/Pin Down
5-1/2” 14.0 - 20.0 4.778 5.012 4.625 1.900 NU 10RD 1.531 1.660 EU 8RD 1.313 1.969
7” 23.0 - 32.0 6.094 6.366 5.938 2.375” EU 8RD 1.938 2.375” EU 8RD 1.938 2.688
7” 17.0 - 29.0 6.184 6.538 6.000 2.375” EU 8RD 1.938 2.375” EU 8RD 1.938 2.688
8-5/8” 28.0 - 40.0 7.725 8.017 7.531 2.375” EU 8RD 2.406 2.375” EU 8RD 2.406 3.250
9-5/8” 47.0 - 53.0 8.535 8.681 8.250 3.500” EU 8RD 3.000 3.500” EU 8RD 3.000 3.750
9-5/8” 36.0 - 47.0 8.500 8.921 8.500 3.500” EU 8RD 3.000 3.500” EU 8RD 3.000 3.750
PA C K E R A C C E S S O R I E S
Locator Seal NippleThe Locator Seal Nipple provides a sealbetween the tubing and the Hydrow II packer.The seal nipple simply stabs into the sealbore of the packer and requires no tension orrotation to remove it.
J-Latch Seal NippleThe J-Latch Seal Nipple connects the tubingin compression or tension. The J-Latchlatches into the packer when set down weightis applied. A 1/4 turn to the right at the packerand pick-up is required to release the sealnipple from the tool.
Collet Latch Seal NippleThe Collet Latch Seal Nipple is used toconnect the short string into the collet andallows a positive surface indication when thenipple snaps in and out of the packer.Removal of the seal nipple requires straightpick-up of the tubing string.
Telescoping Swivel Sub The Telescoping Swivel Sub allows easymake-up of the tubing string between multi-string packer by enabling rotation as well astelescoping action. The Sub telescopes 24”,but can be furnished with various lengths.
Adjustable Sub With Rotational Lock The Adjustable Sub is designed to beinstalled below the Hydrow II packer in orderto make it easier to connect or space out thetubing between multiple string packers. Therotational lock locks the sub in place at anydesired length (up to 24”) to preventtelescoping or rotational movement.
Expendable Seating SubThe Expendable Seating Sub is designed totemporarily plug the tubing below a hydraulicset packer by dropping a ball down the tubinginto a seat designed to shear-out at a givenpressure, depending on the number of shearpins used.
Hydrow II Accessories
RETRIEVABLE PACKERS
AD-1 Tension Packer
DescriptionThe AD-1 is a tension set, retrievable packer.
Applications• Waterflood• Shallow or low fluid level wells with insufficient
tubing weight to set compression packers
Features• Compact• J-slot control for normal set and release• Shear ring secondary release• Right-hand safety joint emergency release• Rocker type slips• Inexpensive• Parts interchangeable with other manufacturers
Specifications
Casing Packer
O.D. Wt. Min. Max. Max. StandardO.D. Box x PIN
4-1/2” 9.5 - 13.5 3.910 4.160 3.771 2-3/8” EU 8RD
5” 15 - 18 4.161 4.408 4.125 2-3/8” EU 8RD11.5 - 15 4.408 4.560 4.250 2-3/8” EU 8RD
5-1/2” 26 4.408 4.560 4.250 2-3/8” EU 8RD20 - 23 4.625 4.778 4.500 2-3/8” EU 8RD
15.5 - 20 4.778 4.950 4.641 2-3/8” EU 8RD13 - 15.5 4.950 5.190 4.781 2-3/8” EU 8RD
5-3/4” 22.5 4.950 5.190 4.781 2-3/8” EU 8RD
6” 26 4.950 5.190 4.781 2-3/8” EU 8RD20 - 23 5.191 5.390 5.062 2-3/8” EU 8RD15 - 18 5.391 5.560 5.156 2-3/8” EU 8RD
6-5/8” 34 5.561 5.595 5.406 2-3/8” EU 8RD28 - 32 5.596 5.791 5.484 2-3/8” EU 8RD
24 5.830 5.921 5.656 2-7/8” EU 8RD17 - 20 5.922 6.135 5.812 2-7/8” EU 8RD
7” 38 5.830 5.921 5.656 2-7/8” EU 8RD32 - 35 5.922 6.135 5.812 2-7/8” EU 8RD26 - 29 6.136 6.276 5.968 2-7/8” EU 8RD20 - 26 6.276 6.456 6.078 2-7/8” EU 8RD17 - 20 6.456 6.538 6.266 2-7/8” EU 8RD
7-5/8” 33.7 - 39 6.539 6.765 6.453 2-7/8” EU 8RD24 - 29.7 6.766 7.025 6.672 2-7/8” EU 8RD20 - 24 7.025 7.125 6.812 2-7/8” EU 8RD
8-5/8” 40 - 49 7.511 7.725 7.312 3-1/2” EU 8RD32 - 40 7.725 7.921 7.531 3 -1/2” EU 8RD20 - 28 7.922 8.191 7.781 3 -1/2” EU 8RD
9-5/8” 47 - 53.5 8.300 8.681 8.218 4-1/2” LTC 8RD40 - 47 8.681 8.835 8.437 4-1/2” LTC 8RD
29.3 - 36 8.836 9.063 8.593 4-1/2” LTC 8RD
10-3/4” 32.7 - 55.5 9.625 10.192 9.500 5” LTC x 5” STC
Note:Additional sizes available on request.
RETRIEVABLE PACKERS
ADL-1 Tension Packer
The ADL-1 is a large bore, tension set, retrievable packer.
Applications• Waterflood• Shallow or low fluid level wells with insufficient tubing
weight to set compression packers
Features• Compact• J-slot control for normal set and release• Shear ring secondary release• Right-hand safety joint emergency release• Rocker type slips• Inexpensive• Large bore• Parts interchangeable with other manufacturers
Setting ProcedureRun the packer to desired setting depth, making the last movement downward.Rotate the tubing to the left one-quarter turn at the tool. Then pick-up and pack-off.
Releasing ProcedureLower the tubing at least one foot more than is needed to remove appliedtension so that the j-pin will move fully to the top of the j-slot.
Rotate the tubing to the right one-quarter turn at the packer so slips will nowbe in the running position. Packer can be moved to a new position and resetor it can be retrieved.
As an alternate release method, the ADL-1 Tension Packer has shear ringsdesigned to part at tension varying from 13,000 to 100,000 lbs. The cone,packing element and guide drop down are carried out of the hole by the bottomsub.
For emergency tubing retrieval, left-hand threads on the top sub of the packerallow the tubing to be retrieved when the packer will not otherwise release.
Specifications
Casing Packer
O.D. Wt. Min. Max. Size Max. StandardO.D. Box x PIN
5-1/2” 13 - 17 4.876 5.044 5-1/2 x 2.90 4.750 3-1/2” EU 8RD
6” 23 - 26 5.140 5.240 6 x 2.90 5.000 3-1/2” EU 8RD18 - 20 5.241 5.424 6 x 2.90 5.218 3-1/2” EU 8RD
7” 23 - 29 6.136 6.366 7 x 4.12 5.96817 - 20 6.367 6.538 7 x 4.12 6.266
4-1/2” LTCor
4-1/2” STC8-5/8” 24 - 32 7.921 8.097 8-5/8 x 4.00 7.600
RETRIEVABLE PACKERS
Shear Tension Packer
Shear Tension Packer is an economical packer designed to be used inwaterflood, injection and pumping wells. A built-in shear safety allows thepacker to be retrieved by applying tension. The packer comes standard withstainless steel drag springs. Protective coatings are available for corrosiveenvironments.
Product Features• Long packing element to give maximum sealing area• Built-in shear safety release• Stainless steel drag springs• Special coatings available• Left hand safety joint emergency release
Specifications
Casing O.D. WT. Max O.D. Connection
3-1/2” 7.7 - 10.2 2.781 1.900 EU 10RD
2-7/8” 6.4 - 6.5 2.250 1.315 EU 10RD
4” 9.5 - 11.0 3.25 2.375 EU 8RD
4-1/2” 9.5 - 13.5 3.75 2.375 EU 8RD
4-1/2” 3.50 2.375 EU 8RD15.1 - 16.6
5” 11.5 - 18.0 4.125 2.375 EU 8RD
5-1/2” 13.0 - 20.0 4.625 2.375 EU 8RD
5-1/2” 20.0 - 23.0 4.50 2.375 EU 8RD
5-1/2” 13.0 - 20.0 4.625 2.875 EU 8RD
5-1/2” 20.0 - 23.0 4.50 2.875 EU 8RD
7” 17.0 - 29.0 6.00 2.875 EU 8RD / 3.500 EU 8RD
7” 32.0 - 38.0 5.50 2.875 EU 8RD / 3.500 EU 8RD
7-5/8” 20.0 - 33.7 6.625 2.875 EU 8RD / 3.500 EU 8RD
8-5/8” 24.0 - 40.0 7.50 2.875 EU 8RD / 3.500 EU 8RD
8-5/8” 20.0 - 28.0 7.75 2.875 EU 8RD / 3.500 EU 8RD
9-5/8” 29.3 - 43.5 8.50 2.875 EU 8RD / 3.500 EU 8RD
9-5/8” 43.5 - 53.5 8.250 2.875 EU 8RD / 3.500 EU 8RD
9-5/8” 32.3 - 53.5 8.500 4.500 LTC
10-3/4” 32.7 - 55.5 9.50 3.500 EU 8RD
11-3/4” 38.0 - 60.0 10.375 3.500 EU 8RD / 3.500 EU 8RD
13-3/8” 48.0 - 72.0 12.00 3.500 EU / 4.50 E U 8RD
Note: Additional sizes available on request.
RETRIEVABLE PACKERS
“G” Compression Packer
DescriptionThe “G” is a compression set, retrievable packer.
ApplicationsMost low pressure production applications. When combined with an unloaderand hold down mechanism it can be used for well stimulation, testing and otherpressuring operations and then left in the well as a production packer.
Features• Rocker type slips• Inexpensive• J-slot control for normal set and release• Right-hand safety joint emergency release• Parts interchangeable with other manufacturers• Compact
Specifications
Casing Packer
O.D. Wt. Min. Max. Max. StandardO.D. Box x PIN
4-1/2” 9.5 - 13.5 3.910 4.160 3.771 2-3/8” EU 8RD
5” 15 - 18 4.161 4.408 4.125 2-3/8” EU 8RD11.5 - 15 4.408 4.560 4.250 2-3/8” EU 8RD
5-1/2” 26 4.408 4.560 4.250 2-3/8” EU 8RD20 - 23 4.625 4.778 4.500 2-3/8” EU 8RD
15.5 - 20 4.778 4.950 4.641 2-3/8” EU 8RD13 - 15.5 4.950 5.190 4.781 2-3/8” EU 8RD
5-3/4” 22.5 4.950 5.190 4.781 2-3/8” EU 8RD
6” 26 4.950 5.190 4.781 2-3/8” EU 8RD20-23 5.191 5.390 5.062 2-3/8” EU 8RD
15 - 18 5.391 5.560 5.156 2-3/8” EU 8RD
6-5/8” 34 5.561 5.595 5.406 2-3/8” EU 8RD28 - 32 5.596 5.791 5.484 2-3/8” EU 8RD
24 5.830 5.921 5.656 2-7/8” EU 8RD17 - 20 5.922 6.135 5.812 2-7/8” EU 8RD
7” 38 5.830 5.921 5.656 2-7/8” EU 8RD32 - 35 5.922 6.135 5.812 2-7/8” EU 8RD26 - 29 6.136 6.276 5.968 2-7/8” EU 8RD20 - 26 6.276 6.456 6.078 2-7/8” EU 8RD17 - 20 6.456 6.538 6.266 2-7/8” EU 8RD
7-5/8” 33.7 - 39 6.539 6.765 6.453 2-7/8” EU 8RD24 - 29.7 6.766 7.025 6.672 2-7/8” EU 8RD20 - 24 7.025 7.125 6.812 2-7/8” EU 8RD
8-5/8” 40 - 49 7.511 7.725 7.312 3-1/2” EU 8RD32 -40 7.725 7.921 7.531 3-1/2” EU 8RD20 - 28 7.922 8.191 7.781 3-1/2” EU 8RD
9-5/8” 47 - 53.5 8.300 8.681 8.218 4-1/2” LTC x STC4-1/2” 40 - 47 8.681 8.835 8.437 4-1/2” LTC x 4-1/2” STC
29.3 - 36 8.836 9.063 8.593 4-1/2” LTC x 4-1/2” STC
10-3/4” 32.7 - 55.5 9.625 10.192 9.500 4-1/2” LTC x 4-1/2” STC
Note: Additional sizes available on request.
R E T R I E VA B L E PA C K E R S
Snap Series (I,II) Packers
The Snap Series Packers are compression set tools which only requirestraight set down weight to pack off. They are generally run above anotherpacker for selective production, treating or injection in multiple zone completions. They are also used to isolate casing holes or perforations.
The Snap I Packer is the basic packer of the series. This has upper or lowerslips and should be used only where intermediate differential pressures areexpected.
The Snap II Packer is a modification of Snap I Packer with the addition ofupper hold down slips for use in applications where high differential pressureis expected from below the packer.
The Snap Series is designed with an internal latch which prevents the packersfrom presetting while running in the hole. The tools are keyed to allow tubingtorque in either direction.
Product Features• Internal By-pass• Equalizing Valve• Internal latch to prevent presetting• Pressure compensating piston on Snap II
Specifications (Snap 1)
Casing WT. O.D. of Nominal Packer StandardSize Tool Casing I.D. Bore (in) Thread
Range ConnectionMin. Max.
3-1/2” 7.7 - 10.2 2.781 2.922 3.068 1.250 1.900 NU 10RD
4-1/2” 9.5 - 13.5 3.750 3.920 4.090 1.875 2.375 EU 8RD
5-1/2” 13.0 - 20.0 4.625 4.778 5.044 2.000 2.375 EU 8RD
5-1/2” 20.0 - 23.0 4.500 4.670 4.778 2.000 2.375 EU 8RD
5-1/2” 20.0 - 23.0 4.500 4.670 4.778 2.375 2.875 EU 8RD
5-1/2” 13.0 - 20.0 4.625 4.778 5.044 2.375 2.875 EU 8RD
7” 17.0 - 26.0 6.094 6.276 6.538 2.500 2.875 EU 8RD
7” 26.0 - 35.0 5.875 6.004 6.276 2.875 3.000 EU 8RD
9-5/8” 40.0 - 53.5 8.250 8.535 8.835 3.000 3.500 EU 8RD
(see more specification charts on next page)
Note:Additional sizes available on request.
Snap II
Snap III
Snap IV
Snap IV
RETRIEVABLE PACKERS
Snap Series (I,II) Packers
Specifications (Snap II)
Casing WT. O.D. of Nominal Packer StandardSize Tool Casing I.D. Bore (in) Thread
Range ConnectionMin. Max.
3-1/2” 7.7 - 10.2 2.781 2.922 3.068 1.260 1.900 NU 10RD
4-1/2” 9.5 - 13.5 3.750 3.920 4.090 1.937 2.375 EU 8RD
5-1/2” 13.0 - 20.0 4.625 4.778 5.044 2.000 2.375 EU 8RD
5-1/2” 20.0 - 23.0 4.500 4.670 4.778 2.000 2.375 EU 8RD
5-1/2” 20.0 - 23.0 4.500 4.670 4.778 2.375 2.875 EU 8RD
5-1/2” 13.0 - 20.0 4.625 4.778 5.044 2.375 2.875 EU 8RD
7” 17.0 - 26.0 6.000 6.276 6.538 2.500 2.875 EU 8RD / 3-1/2” EU 8RD
7” 26.0 - 35.0 5.875 6.004 6.276 2.500 2.875 EU 8RD / 3-1/2” EU 8RD
9-5/8” 40.0 - 53.5 8.250 8.535 8.835 3.000 3.500 EU 8RD
Note: Additional sizes available on request
RETRIEVABLE PACKERS
Set Down Isolation Packer
The Set Down Isolation Packer is a short, economical packer designed toisolate a zone, casing leak or perforations. The packer is designed to runabove any compression set packer and no rotation is required to set or releasethe tool. For low to moderate pressure applications
Product Features• Full opening• Straight set down to set, straight pick up to release• Keyed mandrel• Adjustable shear set• Long packing element
Specifications
Casing O.D. Casing WT. Connection
4-1/2” 9.5 - 13.5 2.375 EUE 8RD
5” 11.5 - 21.0 2.375 EUE 8RD
5-1/2” 14.0 - 20.0 2.375 EUE 8RD
5-1/2” 14.0 - 20.0 2.875 EUE 8RD
7” 17.0 - 26.0 2.875 EUE 8RD
7” 26.0 - 32.0 2.875 EUE 8RD
7-5/8” 20.0 - 29.7 2.875 EUE 8RD
7-5/8” 33.7 - 39.0 2.875 EUE 8RD
9-5/8” 40.0 - 47.0 4.500 EUE 8RD
Note: Additional sizes available on request.
R E T R I E VA B L E PA C K E R S
Tubing Pressure Packer and Casing Packer
Tubing Pressure PackerThe Tubing Pressure Packer is designed to handle a variety of downholeneeds in slim hole casing. It is used for acidizing, fracturing and water injectionwhere moderate pressure is expected. The packer may be run in eithertension or compression.
Casing PackerThe Casing Packer can be set in open hole or in the casing string. It is oftenrun beneath casing holes to isolate water so the well can be pumped or gasvented. The packer can be set in tension or compression for shutting off water,for injection or for various cementing procedures. When run in compressionand in conjunction with special release sub, the packer can be used as a linerhanger.
Deeply cut, widely spaced wickers allow the packer to set, whether it is in openhole or in corroded casing. The Casing Packer is also available for open holeswith a softer dual packing element system. This system provides a morereliable pack-off in irregular formations and a trouble free release withoutswabbing.
Features• Full opening casing size• Deep cut wickers• Compression or tension set• Casing can be run below packer• Can be used as a liner hanger• Available in open hole version
Tubing Pressure Packer Specifications (2-3/8” 3-1/2”) chart 1
Casing WT. O.D. of Nominal Min. StandardSize Tool Casing I.D. Tool I.D. Thread
Range ConnectionMin. Max.
2-3/8” 4.0 - 4.7 1.813 1.995 2.041 0.750 1.00 11-1/2 LPor .75 NPT
2-7/8” 8.6 - 8.7 2.062 2.165 2.259 1.125 1.660 NU10 RD
6.4 - 6.5 2.250 2.375 2.441 .750 1.00 11-1/2 LPor .75 NPT
3-1/2” 12.950 2.625 2.729 2.770 1.125 1.900 or1.660 NU 10RD
7.7 - 10.2 2.750 2.922 3.068 1.125 1.900 or1.660 NU 10RD
(see more specifications on next page)
R E T R I E VA B L E PA C K E R S
Casing Packer Specifications (4-1/2” - 16”) Chart 2
Casing WT. O.D. of Nominal Min. StandardSize Tool Casing I.D. Tool I.D. Thread
Range ConnectionMin. Max.
4-1/2” 15.1 3.500 3.750 4.000 1.938 2.375 EU 8RD9.5 - 13.5 3.750 3.920 4.090 2.500 2.875 EU 8RD
5” 11.5 - 18.0 4.125 4.276 4.560 2.500 2.875 EU 8RD
5-1/2” 20.0 - 23.0 4.500 4.670 4.788 3.000 3.500 EU 8RD13.0 - 17.0 4.625 4.892 5.044 3.000 3.500 NU 10RD
13.0 - 17.0 4.625 4.892 5.044 3500 4.000 NU 8RD
6” 18.0 - 20.0 5.188 5.352 5.424 3.500 4.000 NU 8RD
6-5/8” 20.0 - 28.0 5.625 5.791 6.049 3.500 4.000 NU 8RD20.0 - 28.0 5.625 5.791 6.049 4.000 4.500 LTC 8RD
7” 17.0 - 38.0 5.750 5.920 6.538 4.000 4.500 LTC 8RD20.0 - 26.0 6.125 6.276 6.456 4.500 5.000 LTC 8RD17.0 - 23.0 6.188 6.366 6.538 4.500 5.000 LTC 8RD
7-5/8” 20.0 - 33.7 6.625 6.765 7.125 4.000 4.500 LTC 8RD20.0 - 33.7 6.500 6.765 7.125 5.000 5.500 LTC 8RD
8-5/8” 32.0 - 44.0 7.375 7.625 7.921 5.000 5.500 LTC 8RD24.0 - 40.0 7.500 7.725 8.097 4.000 4.500 LTC 8RD24.0 - 40.0 7.500 7.725 8.097 5.000 5.500 LTC 8RD24.0 - 36.0 7.625 7.825 8.097 6.000 6.625 LTC 8RD
9-5/8” 43.5 - 53.5 8.250 8.535 8.755 4.000 4.500 LTC 8RD43.5 - 53.5 8.250 8.535 8.755 6.500 7.000 LTC 8RD32.6 -43.5 8.250 8.755 9.001 6.000 6.625 LTC 8RD32.6 -43.5 8.250 8.755 9.001 6.000 7.000 LTC 8RD
10-3/4” 32.75 - 55.5 9.500 9.760 10.192 6.500 7.000 LTC 8RD
11-3/4” 42.0 - 54.0 10.625 10.880 11.084 8.000 8.625 LTC 8RD
13-3/8” 48.0 - 72.0 12.000 12.347 12.715 9.000 9.625 LTC 8RD
16” 65.0 - 84.0 14.750 15.010 15.250 9.000 9.625 LTC 8RD65.0 - 84.0 14.700 15.010 15.250 12.500 13.375 LTC 8RD
Note:Additional sizes available on request.
RETRIEVABLE PACKERS
“B” Tubing Anchor Catcher
DescriptionThe “B” acts as a tubing anchor to maintain tension in the tubing string and asa tubing catcher to prevent parted pipe from falling to the bottom of the well.
Applications• Most rod pumping applications where it is important to
maintain tension in the tubing.
Features• Rotate left to set, right to release• Straight pull emergency shear release• Increases pump efficiency• Improves operating costs by reducing maintenance
and down time caused by tubing or sucker rod wear• Optional right hand set• Parts interchangeable with other manufacturers
Specifications
Casing Anchor
O.D. Wt. Min. Max. Size Max. StandardO.D. Box x PIN
4” 9.5 - 12.6 3.250 3.562 41 2.875
4-1/2” 9.5 - 13.5 3.826 4.090 43A 3.750 2-3/8” EU8 RND
5” 11.5 - 18 4.276 4.560 43B 4.000
5-3/4” 11.5 - 15 4.408 4.778 43C 4.125
5-1/2” 13 - 23 4.670 5.044 45A 4.500
6” 18 - 23 5.240 5.424 45B 4.812 2-3/8” EU8 RND
6-5/8” 17 - 32 5.675 6.456 47A 5.500 or2-7/8”
7” 20 - 38 5.675 6.456 47B 5.500 8 RND17 - 20 6.413 7.125 47B 6.250
7-5/8” 20 - 39 6.413 7.125 47B 6.250
6-5/8” 17 - 20 5.675 6.538 47 x 3.00 5.500
7-5/8” 17 - 38 5.675 6.538 47 x 3.00 5.500 3-1/2” EU8 RND
8-5/8” 24 - 49 7.250 8.093 49 7.000
9-5/8” 32.3 - 47 8.681 9.001 51 8.000
Note: Additional sizes available on request.
10-3/4” 32.75 - 65.7 9.560 10.192 53 8.656
PACKER ACCESSORIES
PA C K E R A C C E S S O R I E S
On-Off Tool
The “On-Off” Tool is a left hand release, tubing disconnect device that has aninternal lock profile for securing flow control equipment.
ApplicationsOperations that require tubing disconnect and re-engagement withoutdisturbing the packer. The internal lock profile is used to retain flow controldevices such as plugs, valves, chokes, or regulators.
Features• Left hand release, auto-on• Optional right hand release• Bonded seals allow multiple disconnects• Can be pinned in a shear-up or shear-down position• X, F and R Internal Lock Profiles are available• Straight set down to engage
Specifications
—Overshot—
Tubing Size Casing Size
4-1/2” 5-1/2” 7” 7-5/8” 8-5/8” 9-5/8”
2-3/8” • • •
2-7/8” • • • • •
3-1/2” • • • •
—Seal Nipple—
Tubing Size F - Seal Bore / X - Seal Bore
1.781 1.812 1.875 2.250 2.312 2.750 2.812
2-3/8” • • •
2-7/8” • • • • •
3-1/2” • • • • • • •
—Overshot—
Tubing Size R - Seal Bore
1.781 1.812 1.875 2.250 2.312 2.750 2.812
2-3/8” • • •
2-7/8” • • • • •
3-1/2” • • • • • • •
Note: Other Seal Bores available upon request.
PA C K E R A C C E S S O R I E S
Sliding Sleeve
The Sliding Sleeve is a simple, downhole flow control tool used to establishselective communication between the tubing and annulus at any desired timeand can be opened and closed by standard wireline methods.
The Sliding Sleeve can be utilized for displacing the annulus or tubing afterflanging up the wellhead, for selective testing, treating and/or production, aswell as producing multiple zones through a single string.
Product Features• Recessed closing sleeve for protection• Incorporates an additional profile seating nipple• Design allows tools to be run in multiples• Proven seal design
Specifications Guide
Tubing Size Profile
2.375 1.78 1.81 1.87
2.875 1.78 1.81 1.87 2.25 2.31
(Other sizes available upon request)
Safety Joints
The Safety Joints allow positive release of the tubing string in completionswhere retrieval problems are anticipated. These safety joints are available inadjustable, straight pull or rotational release versions.
Rotational Specification Guide
Tubing Size O.D. I.D. ThreadConnection
1.660 2.250 1.250 1.660 NU 10RD
2.375 3.063 2.000 2.375 EU 8RD
2.875 3.688 2.500 2.875 EU 8RD
3.500 4.500 3.000 3.500 EU 8RD
Shear Out Specification Guide
Tubing Size OD ID ThreadConnection
1.315 1.750 .750 1.315 NU 10RD
1.660 2.250 1.250 1.660 NU 10RD
1.660 2.063 1.250 1.660 NU 10RD
1.900 2.688 1.610 1.900 NU 10RD
2.375 3.063 2.000 2.375 EU 8RD
2.875 3.688 2.500 2.875 EU 8RD
3.500 4.500 3.000 3.500 EU 8RD
Sliding Sleeve
Rotational
Shear Out
SEAL BORE PACKERS
SEAL BORE PACKERS
Specifications
Casing WT. O.D. of Nominal Packer Min. BoreSize Tool Casing I.D. Bore Through
Range SealsMin. Max.
4-1/2” 15.1 - 16.6 3.600 3.754 3.826 2.390 1.703 / 1.8139.5 - 13.5 3.750 3.920 4.090 2.390 1.703 / 1.8139.5 - 13.5 3.750 3.920 4.090 2.500 1.91013.5 - 15.1 3.594 3.826 3.900 2.500 1.9109.5 - 13.5 3.750 3.920 4.090 2.688 1.938
5” 15.0 - 21.0 3.968 4.156 4.408 2.688 1.938
5-1/2” 23.0 - 26.0 4.250 4.548 4.670 2.688 1.93817.0 - 23.0 4.437 4.670 4.892 2.688 1.93813.0 - 17.0 4.563 4.892 5.044 3.000 2.375 / 2.27017.0 - 23.0 4.437 4.670 4.892 3.000 2.375 / 2.270
6-5/8” 17.0 - 32.0 5.687 5.675 6.135 4.000 3.000
7” 23.0 - 32.0 5.687 6.094 6.366 2.688 1.93832.0 - 38.0 5.468 5.920 6.094 3.250 2.40623.0 - 32.0 5.687 6.094 6.366 3.250 2.40617.0 - 20.0 6.187 6.456 6.538 3.250 2.40632.0 - 38.0 5.687 5.920 6.094 4.000 3.00026.0 - 29.0 5.875 6.184 6.276 4.000 3.00020.0 - 23.0 6.000 6.366 6.456 4.000 3.00017.0 - 20.0 6.250 6.456 6.538 4.000 3.000
7-5/8” 24.0 - 39.0 6.250 6.625 7.025 3.250 2.40633.7 - 39.0 6.250 6.625 6.765 4.000 3.000 24.0 - 33.7 6.500 6.765 7.025 4.000 3.000
8-5/8” 36.0 - 49.0 7.125 7.511 7.825 4.000 3.00024.0 - 36.0 7.500 7.825 8.097 4.000 3.000
9-5/8” 29.3 - 53.5 8.125 8.535 9.063 3.250 2.40629.3 - 53.5 8.125 8.535 9.063 4.750 3.750
10-3/4” 60.7 - 81.0 8.718 9.250 9.660 3.250 2.37560.7 - 81.0 8.718 9.250 9.660 4.000 3.00032.7 - 55.5 9.50 9.760 11.150 3.250 2.37532.7 - 55.5 9.50 9.760 11.150 4.000 3.000
11-3/4” 38.0 - 60.0 9.50 9.760 11.150 3.250 2.37538.0 - 60.0 9.50 9.760 11.150 4.000 3.000
13-3/8” 48.0 - 80.7 12.000 12.215 12.715 9.00 8.000
Note: Additional sizes available on request.
D & DB Seal Bore Packers
The Seal Bore Packers are highly versatile tools which may be set on wireline,mechanically or hydraulically. They are frequently used on stimulation jobs whereexcessively high pressure and temperatures are encountered. The Seal BorePackers also have several options that allow the packer to be converted to a bridgeplug by installing a Knock-Out plug, Pump-Out Plug or Screw Out Plug to isolate alower zone. The zone may later be produced by removing the plug with theproduction string and landing the seals.
Optional bottoms are available which enable the use of a full line of packer accessoryequipment. There is also a full line of seals to select from including Kalrez, Aflas,Viton, Teflon, Ryton and our own standard Nitrile compound. The DB Packerincorporates the same features as the standard Type D Packer with the addition of alarge upper seal bore. This features allows the largest possible ID through the packerand seals for completions requiring large tubing sizes.
Product Features• Wireline, mechanical or hydraulic setting options• Metal back-up system expands to casing ID to
prevent rubber extrusion• Top connection interchangeable to accept competitive seals• Parts keyed for easy mill-out• Rubber options for high temperatures, H2S and CO2 applications
SEAL BORE PACKERS
BH and DBH Seal Bore Packers
The BH Seal Bore Packer is a hydraulic set version of the standard type D SealBore Packer. The packer is run to setting depth on the tubing string and setwith tubing pressure making it ideal for deviated holes or wells with doglegs.
The DBH Seal Bore Packer is the same as the addition of a large upper sealbore to allow the largest possible ID through the seals and packer.
Product Features• One trip setting• Metal back-up system expands to casing ID to prevent rubber extrusion• Top connection interchangeable to accept competitive seals• Parts keyed for easy mill-out• Elastomer options for high temperatures, H2S and CO2 applications
Specifications
Casing WT. Model O.D. of Nominal Packer Min. BoreSize Tool Casing I.D. Bore Through
Range SealsMin. Max.
5-1/2” 13.0 - 23.0 DBH 4.438 4.670 5.044 2.688/1.938 1.938
6-5/8” 17.0 - 32.0 BH 5.468 5.675 6.135 3.250 2.406
7” 23.0 - 32.0 BH 5.875 6.094 6.366 3.250 2.406
9-5/8” 29.3 - 53.5 BH 8.125 8.535 9.063 4.750 3.750
9-5/8” 40.0 - 58.4 BH 8.125 8.435 8.835 6.000 4.875
Note: Additional sizes available on request.
SEAL BORE PACKERS
“AP” Retrievable Seal Bore Packer
The “AP” Retrievable Seal Bore Packer delivers high performance withsimplicity of design and desirable economics. It is a 10,000 PSI plus ratedpacker and can be equipped to withstand severe corrosion and hightemperatures.
The “AP” Retrievable Seal Bore Packer is set on wireline or tubing and iseasily retrieved. This tool has undergone an intense testing and developmentprogram with consistently successful results. It is ideally suited for use as agravel pack packer, but will also handle deep, high pressure completions.
The “AP” Retrievable Seal Bore Packer is designed with a unique sealingsystem and has proven itself to be a superior seal. These packing elementspackoff easily and still resist swab-off.
Product Features• High pressure rating• High temperature rating• “Ecner” array packing elements system• Sets in a wide range of casing I.D.• Extremely short design• Minimal o-ring required• Wireline set• Optional tubing set using hydraulic setting tool
Specifications
Casing WT. O.D. of Nominal Packer Min. BoreSize Tool Casing I.D. Bore Through
Range SealsMin. Max.
5” 18.0 - 21.4 3.969 4.176 4.276 2.688 1.938
5” 11.5 - 15.0 4.250 4.408 4.560 2.688 1.938
5-1/2” 20.0 - 23.0 4.500 4.670 4.778 3.000 2.375
5-1/2” 13.0 - 20.0 4.625 4.788 5.044 3.000 2.375
7” 23.0 - 32.0 5.938 6.094 6.366 3.250 2.406
7” 29.0 - 35.0 5.813 6.004 6.184 3.250 2.406
7” 29.0 - 35.0 5.813 6.004 6.184 4.000 3.000
7” 23.0 - 32.0 5.938 6.094 6.366 4.000 3.000
7-5/8” 29.7 - 39.0 6.438 6.625 6.875 4.000 3.000
7-5/8” 20.0 - 29.7 6.688 6.875 7.125 4.000 3.000
9-5/8” 32.6 - 43.5 8.539 8.755 9.001 4.000 3.000
9-5/8” 32.6 - 43.5 8.539 8.755 9.001 6.000 4.875
9-5/8” 47.0 - 53.5 8.319 8.535 8.681 6.000 4.875
Note:Additional sizes available on request.
Extreme Ser vice Packer
Extreme Service Permanent Packer
The ES Extreme ServicePermanent Production Packer
The ES Seal Assembly Is "service matched" to today's deeper, hotter well environments. The ES Packer is designed to withstand full differential pressure with the seal assembly latched into the packer bore. The 450º F. Temperature rating insures suitability with operating conditions in deeper wells. The ES provides a unique slip arrangement, utilizing dual upper and lower slips and cones to more effectively distribute pressure induced forces into the supporting casing. Each set of slips is one-piece construction with inserts strategically positioned to provide maximum packer retention under extreme loads. The lower slips are secured to the packer mandrel through a threaded connection to avoid damage while the packer is going into the hole.
The ES packing element design incorporates positive anti-extrusion components to eliminate element extrusion under pressure and temperature extremes. Non-elastomer sealing mechanisms at threaded connections insure maximum pressure performance. A large bore through the mandrel and a complete line of accessories make the ES packer an excellent choice for high-flow production applications or situations demanding high volume sand fracs.
ES Seal Assembly
The ES Seal Assembly is a matched performance design accessory for the ES packer. This seal assembly features a jay lug locking system capable of withstanding the loads induced by the full pressure capability of the ES packer. The jay lug lock, combined with an autojay packer top provides easy seal assembly stabbing and facilitates space out of the production tubing string. A half turn to the right, at the packer, quickly releases the seal assembly.
ES Seal Assembly seal units are full performance seals rated for 450º F at 15,000 psi pressure conditions. A full range of elastomers is available for special wellbore conditions and fluids. Additional seal units can be added when the packer is run with seal bore extensions below the packer mandrel. A half-mule shoe, bottom guide aids in stabbing.
Extreme Ser vice Packer
ES Seal Assembly Features:
· 15,000 psi differential pressure capability at 450º F· One-piece, tandem slip and cone configuration for maximum holding
power· Lower slips secured to packer mandrel with a threaded connection· Non-elastomeric sealing mechanism for threaded connections· Full line of accessory equipment for completion flexibility· Can be set hydraulically
Full performance rated at 15,000 psi at 450º F
· 110,000 psi minimum yield alloy steel mandrel is standard· Locator threaded to match tubing connection· Full selection of seal materials match performance with well bore fluids· Integral jay lugs on seal assembly mandrel· Auto-jay latch for easy stabbing and retrieval· Half turn, right hand release or on wireline
Extreme Service Permanent Packer
CASING PACKER SEAL ASSEMBLY SETTING TOOL
O.D. WEIGHT MIN. MAX. SIZE MAX O.D. SEAL BORE SIZE MIN BORE KNOCK ADAPTER BAKER HYDRAULIC
(in) (ppf) (in) (in) (in) (in.) THRU SEALS OUT KIT E-4
(in.) PLUG
4 1/2 9.5-13.5 3.795 4.090 37-26 3.750 2.688 26-18 1.807 26 37-26 Size 10 2 3/8 Tool
5 15-20.8 4.029 4.408 39-26 3.960 2.688 26-18 1.807 26 37-26 Size 10 2 3/8 Tool
5 11.5-13 4.369 4.670 42-26 4.250 2.688 26-18 1.807 26 37-26 Size 10 2 3/8 Tool
5 1/2 20-23 4.545 4.811 44-26 4.500 3.000 30-21 2.125 30 45-30 Size 20 2 7/8 Tool
5 1/2 20-23 4.545 4.811 44-30 4.500 3.000 30-21 2.125 30 45-30 Size 20 2 7/8 Tool
5 1/2 13.5-17 4.767 5.044 45-26 4.641 3.000 30-21 2.125 30 45-30 Size 20 2 7/8 Tool
5 1/2 13.5-17 4.767 5.044 45-30 4.641 3.000 30-21 2.125 30 45-30 Size 20 2 7/8 Tool
7 32-38 5.875 6.094 56-32 5.687 4.000 40-28 2.875 40 56-40 Size 20 2 7/8 Tool
7 32-38 5.875 6.094 56-40 5.687 4.000 40-28 2.875 40 56-40 Size 20 2 7/8 Tool
7 26-32 6.095 6.276 58-32 5.875 4.000 40-28 2.875 40 56-40 Size 20 2 7/8 Tool
7 26-32 6.095 6.276 58-40 5.875 4.000 40-28 2.875 40 56-40 Size 20 2 7/8 Tool
7 17-23 6.456 6.765 61-32 6.187 4.000 40-28 2.875 40 56-40 Size 20 2 7/8 Tool
7 17-23 6.456 6.765 61-40 6.187 4.000 40-28 2.875 40 56-40 Size 20 2 7/8 Tool
7 5/8 33.7-45.3 6.456 6.765 61-32 6.187 4.000 40-28 2.875 40 56-40 Size 20 2 7/8 Tool
7 5/8 33.7-45.3 6.456 6.765 61-40 6.187 4.000 40-28 2.875 40 56-40 Size 20 2 7/8 Tool
7 5/8 24-39 6.706 7.025 63-32 6.375 4.000 40-28 2.875 40 56-40 Size 20 2 7/8 Tool
7 5/8 24-39 6.706 7.025 63-40 6.375 4.000 40-28 2.875 40 56-40 Size 20 2 7/8 Tool
9 5/8 40-58.4 8.279 8.968 82-60 8.218 6.000 60-42 4.25 60 82-60 Size 20 2 7/8 Tool
9 5/8 36.47 8.525 9.050 84-60 8.438 6.000 60-42 4.25 60 82-60 Size 20 2 7/8 Tool
SEAL BORE ACCESSORIES
PA C K E R A C C E S S O R I E S
Seal Bore Packer Accessories
Extensions
Seal Bore ExtensionThese extensions are generally used in installations where floating seals arerequired due to tubing contraction. They are available in five and ten footlengths and allow a continuous seal bore.
Mill-Out ExtensionMill-out extensions are used in installations where floating seals are requiredbut allow a packer with a larger inside diameter to accept a “packer plucker”in the event the packer is milled out.
Concentric CouplingsConcentric couplings are used to connect seal bore extensions to obtainmore seal bore length.
Bottoms
Wireline Guide BottomThis is the standard bottom which serves as a wireline re-entry guide anddoes not accommodate extensions.
Tubing Adapter BottomAvailable with choice of tubing threads for running tail pipe or mill-outextensions below the packer.
Concentric BottomUsed for running a seal bore extension below the packer.
Knock-out Plug BottomUsed for running a knock-out plug in the packer. When the packer is set, thepacker serves as a bridge plug until the plug is knocked out with theproduction string.
Screw-Out Plug Bottom Used for running a screw-out plug in the packer. After being set, the packerserves as a bridge plug until the plug is screwed out of shoe.
Flapper BottomThe Flapper bottom contains a spring loaded flapper type back pressurevalve which holds pressure from below only. The valve is opened when theproduction string is stung into the packer and automatically closes when thestring is retrieved.
Pump-Out PlugThe Pump-out seals off pressure from below so that the packer can serve asa bridge plug. The pump-out plug can be removed by pump pressure to allowa full opening in the packer.
Concentric Coupling
Seal Bore Extension
ConcentricBottom
WirelineGuideBottom
Knock-outPlug Bottom
Screw-outPlug Bottom
FlapperBottom
Mill-out Extension
Tubing AdaptorBottom
Pump-out Plug
Wireline GuideBottom
PA C K E R A C C E S S O R I E S
Seal Bore Tubing Accessories
J-Latch Anchor Assembly
The J-Latch is used with a seal assembly to hold tubing anchored in thepacker. The J-Latch will automatically latch into the packer upon set down.To release the J-Latch from the packer, set down, rotate tubing 1/4 turn tothe right at the packer and pick up. J-Latch Anchor Assemblies are availablefor most seal bore sizes. Double seal units are recommended when using aJ-Latch Anchor Assembly
Threaded Latch Anchor or Snap Latch Seal Assembly
The Threaded Latch is used with a seal assembly to hold tubing anchored inthe packer. The Threaded Latch will automatically latch into the packer uponset down. To release the Threaded Latch from the packer, apply slighttension on the tubing and rotate 8 - 10 turns to the right to release from thePacker. The Threaded Latch Anchor Seal Assembly includes a seal stack asrequired for the downhole environment and application. The snap latch is used
for sump packers.
Locator Sub
The Locator is used with a seal assembly to stop downward tubingmovement but allows the seals to move freely with tubing contraction.Locators are available for most seal bore sizes. Double seal units arerecommended when using a Locator Assembly.
Locator Sub
J-Latch Sub
Thread Latch Anchor SealAssembly
PA C K E R A C C E S S O R I E S
Seal Bore Tubing Accessories (cont)
MOLDED SEALS
Recommended in applications where seal movement or dirty fluids areanticipated. Seals are bonded to a metal sleeve with an internal 0-ring toallow a positive seal. Molded seals are available in Nitrile, HSN, Viton,Flourel, EPOM & ECO.
CHEVRON SEALS
Stack consists of Chevron Seal Rings with steel spacers. Chevron Seals areavailable in Nitrile, Viton, Flourel, Teflon, Aflas, Ryton, and Kalrez materials. Note: Chevron seals are not recommended for movement outside the seal bore.
VTM PREMIUM SEAL
VTM Premium Seal Stack consists of Viton seals, Teflon back-up, knittedwire mesh back-up, male adapter, metal spacer and retaining rings. VTMstacks are recommended for installations similar to VTR stacks but wheremovement or dirty fluids are anticipated.
Half Mule Shoe Guide
Screw Out Shoe Guide
Seal Wireline Re-entry Guide
Locator Sub
Chevron Seal
VTR Premium Seal
AKTM Premium Seal
PA C K E R A C C E S S O R I E S
Seal Bore Tubing Accessories (cont)
Available in a variety of Seal Systems and alloy materials to accommodate
various well conditions. It is important to know the well conditions and work
to be performed in order to choose the proper seal system. Consideration
should be given to temperature (minimum and maximum), concentration of
hostile elements (H 2S, C0 2, etc.), seal movement and maximum pressure
differential. These factors will determine the seal type, metal material and
accessories to be utilized. For all seal bore tubing accessories,
standardization of threads, seal diameters and seal lengths have been
carefully considered in the design to maximize interchangeability with
competitive seal bore equipment.
All steel components for the seal bore tubing accessories are manufactured
to meet N.A.C.E. specifications MR-O1 75 for H 2S service. The accessories
are also available in several types of material with the following three as
an example:
• High strength alloy steel - High pressure applications
• 9CR-I MO or 13CR-1 MO alloy steel - H2S and C02 applications
• Incoloy 925 alloy steel - Severe corrosion applications
Two basic seal types are currently available:• Elastomer bonded to metal commonly known as molded seals and
available in Nitrile, Viton, Flourel, EPDM, ECO and HSN materials.
• Chevron type seals commonly known as V-rings (not recommended to
move out of seal bore) and available in Nitrile, Viton, Flourel, Teflon,
Aflas, Ryton and Kalrez materials.
Temperature, hostile elements, seal movement and pressure differential are
parameters to consider when selecting seal types.
Trademarks
Aflas Trademark of Ashi Glass
Flourel Trademark of 3M
Kalrez Trademark of Dupont
Ryton Trademark of Phillips Petroleum Co.
Teflon Trademark of Dupont
Viton Trademark of Dupont
GENERAL
PARTS LIST
1/4" HEX
THREADLEFT HAND
3/8-24 NF
BLEEDER VALVE ASSY.
(OPTIONAL ACCESSORY)
BLEEDER WRENCHWST-5125-146 WST-5125-142
26
25
24
23
21
22
2.13
2.13
.81 11
12
13
14
15
16
17
18
19
20
2
2.75
3
21
4
3
5
6
3
7
3
10
8
3
1
4.50
63.78
15.50
16.63
.88
13.91
1.00
1.50
2.38
7.50
9
1.75
METI REBMUNTRAP .QER NOITPIRCSED
1 100-01KB-TSWGNITTESERUSSERPENILERIW01EZIS-.YSSA
62-2SMETI.LCNI-LOOT
2 020-01KB-TSW 1 REBMAHCERUSSERP
*3 723-965N-000 41 .ORUD09-GNIR-O
4 430-01KB-TSW 1 BUSEVLAVREDEELB
5 220-01KB-TSW 1 NOTSIPREPPU
6 120-01KB-TSW 1 REDNILYCREPPU
7 320-01KB-TSW 1 ROTCENNOCMEDNAT
8 530-01KB-TSW 1 REDNILYCREWOL
9 420-01KB-TSW 1 NOTSIPREWOL
01 1 .GL8/3x.C.N02-4/1-WERCSTESTEKCOSXEH
11 520-01KB-TSW 1 NIPGNINIATER
21 620-01KB-TSW 1 DORNOTSIP
*31 112-965N-000 2 .ORUD09-GNIR-O
41 720-01KB-TSW 1 DAEHREDNILYC
51 1 .GL2/1x.C.N61-8/3-WERCSTESTEKCOSXEH
61 1 .GL8/3x.C.N61-8/3-WERCSTESTEKCOSXEH
71 920-01KB-TSW 1 GNIRGNINIATER
81 130-01KB-TSW 1 KNILSSORC
91 820-01KB-TSW 1 EVEELSKNILSSORC
02 030-01KB-TSW 1 LERDNAMGNITTES
12 241-5215-TSW 1 62-22SMETI.LCNI-EVLAVREDEELB-.YSSA
22 341-5215-TSW 1 EVLAVREDEELBROF-METS
32 441-5215-TSW 1 EVLAVREDEELBROF-TUNRENIATER
42 541-5215-TSW 1 EVLAVREDEELBROF-TAES
*52 312-965N-000 1 EVLAVREDEELBROF-.ORUD09-GNIR-O
*62 210-965N-000 1 EVLAVREDEELBROF-.ORUD09-GNIR-O
* 010-01KB-TSW100-01KB-TSWROF-°523-TIKGNIR-O
-62DNA,52,31,3SMETI.LCNI
SIZE 10 WIRELINE PRESSURE SETTING TOOL
WST-5125-142BLEEDER VALVE ASSY.
22
BLEEDER WRENCHWST-5125-146
23
20
21
19
3/8-24 NF
LEFT HANDTHREAD
18
1/4" HEX
(OPTIONAL ACCESSORY)
METI REBMUNTRAP .QER NOITPIRCSED
1 100-02KB-TSWGNITTESERUSSERPENILERIW02EZIS-.YSSA
32-2SMETI.LCNI-LOOT
2 020-02KB-TSW 1 REBMAHCERUSSERP
*3 433-965N-000 41 .ORUD09-GNIR-O
4 220-02KB-TSW 1 NOTSIPREPPU
5 120-02KB-TSW 2 REDNILYC
6 320-02KB-TSW 1 ROTCENNOCMEDNAT
7 420-02KB-TSW 1 NOTSIPREWOL
8 520-02KB-TSW 1 NIPKCOL
9 620-02KB-TSW 1 DORNOTSIP
*01 612-965N-000 2 .ORUD09-GNIR-O
11 720-02KB-TSW 1 DAEHREDNILYC
21 1 .GL2/1x.C.N61-8/3-WERCSTESTEKCOSXEH
31 920-02KB-TSW 1 GNIRGNINIATERKNILSSORC
41 1 .GL8/3x.C.N02-4/1-WERCSPACTEKCOSXEH
51 130-02KB-TSW 1 KNILSSORC
61 820-02KB-TSW 1 EVEELSKNILSSORC
71 030-02KB-TSW 1 LERDNAMGNITTES
81 241-5215-TSW 1 32-91SMETI.LCNI-EVLAVREDEELB-.YSSA
91 341-5215-TSW 1 EVLAVREDEELBROF-METS
02 441-5215-TSW 1 EVLAVREDEELBROF-TUNRENIATER
12 541-5215-TSW 1 EVLAVREDEELBROF-TAES
*22 312-965N-000 1 EVLAVREDEELBROF-.ORUD09-GNIR-O
*32 210-965N-000 1 EVLAVREDEELBROF-.ORUD09-GNIR-O
* 010-02KB-TSW100-02KB-TSWROF-°523-TIKGNIR-O
-32DNA,22,01,3SMETI.LCNI
PARTS LIST
3
4
5
3
6
3
7
8
9
5
3
1
10
11
12
13
14
15
16
17
3.8
5.2
3.5
13
21.5
1.00
74.88
21.5
1.25
10.06
6.56
3.25
3.00
1.75
2.25
1.12
2
18
SIZE 20 WIRELINE PRESSURE SETTING TOOL
12. PLACE TOOL IN VISE AND TIGHTEN ALL JOINTS. AIR TRAPPED IN CYLINDER DURING TIGHTENINGSHOULD MAKE CROSSLINK SLEEVE STAND OFF FROM CYLINDER HEAD NO MORE THAN 3/8".
VALVE (3 AND 18) IN PRESSURE CHAMBER (2).1. INSTALL O-RINGS AND MANUAL BLEEDER
2 18 3 5
2. INSTALL O-RINGS (3) ON UPPER PISTON (4)THEN PUSH PISTON THROUGH CYLINDER
43
SCREW CHAMBER TO CYLINDER (5). UNTIL IT CONTACTS PRESSURE CHAMBER.
LONG THREAD END
5. SLIDE SETTING MANDREL (17)
1716
6. SLIDE PISTON ROD (9)
17 9
7. ALIGN SLOTS IN ALL ITEMSAND INSERT CROSSLINK (15).
141315
INSIDE CROSSLINK SLEEVE (16).LONG THREADED END OF MANDRELPOSITIONED AS SHOWN.
INTO SETTING MANDREL (17).
INSTALL RETAINING RING (13)AND CAP SCREW (14).
5
WHILE CYLINDER IS BEING MADE UP.MAKING SURE CYLINDER HEAD IS POSITIONED AGAINST CROSSLINK SLEEVESLIDE CYLINDER OVER PISTON AND MAKE UP TO CYLINDER HEAD WHILE10. LUBRICATE PISTON, CYLINDER HEAD THREADS, AND CYLINDER BORE.
8. INSTALL O-RINGS (3 AND 10) TO CYLINDER HEAD (11).SLIDE HEAD ON PISTON ROD. MAKE UP HEAD HANDTIGHT TO SETTING MANDREL. INSTALL SET SCREW (12).
1112 3 10
PLACE PISTON ON PISTON ROD. INSTALL9. INSTALL O-RINGS (3) ON LOWER PISTON (7).
78 3
LOCK PIN (8) AND TIGHTEN.
11. CONNECT UPPER ANDLOWER HALVES OF THETOOL TOGETHER.
TO FOLLOWING LEVELS:3. FILL CYLINDER WITH SAE 10-40 OIL
350° F - 400° F275° F - 350° F200° F - 275° F200° F OR LESSWELL TEMP. SIZE 10 SIZE 20
4-1/8 IN. 4-3/8 IN. 4-5/8 IN.
4 IN. 4 IN.
5-1/2 IN.
4-1/2 IN. 5 IN.
ORIFICE TOWARD OIL.CYLINDER WITH SMALLTHEN SCREW INTO UPPERTANDEM CONNECTOR (6)4. INSTALL O-RINGS (3) ON
6
3
SIZE 20 WIRELINE SETTING TOOLASSEMBLY INSTRUCTIONS
1. Hose off setting assembly to clean and cool it. Unscrew the cable head. If the cable head is tight, pressuremay have leaked into it. In this case bleed pressure from tool (steps 3 and 4) before removing cable head.
2. Remove the setting adapter kit. Hold ear of lock spring with pliers and twist against spring to relieve the bindon the threads. Unscrew the Tension Mandrel.
3. Place chain tongs around Lower Cylinder. Position bleeder holes in Cylinder facing away from you and SLOWLYunscrew Cylinder Head until compressed air escapes. DO NOT BACK-OFF CYLINDER HEAD FROM CYLIN-DER MORE THAN 1-1/4”.
4. Preferred gas pressure bleed-off method: Position setting assembly so that side vent for Manual BleederValve is facing away from you and the Bleeder Stem is FACING UP. Using Bleeder Wrench, slowly turn Stemto LEFT until gas pressure escapes through the side vent. The Stem will shoulder at Retainer Nut.
5. Alternate gas pressure bleed-off method: Place chain tongs around Pressure Chamber. Position bleeder holein Pressure Chamber facing away from you. SLOWLY unscrew the Firing Head until gas pressure bleeds off.DO NOT BACK-OFF FIRING HEAD FROM PRESSURE CHAMBER MORE THAN 1-1/4”.
6. Alternate gas pressure bleed-off method: Should pressure not bleed off as explained in steps 4 and 5 anothermethod is available. Place chain tongs around Upper Cylinder and position bleeder hole in Cylinder pointingaway from you. SLOWLY unscrew the Pressure Chamber until gas pressure bleeds off. DO NOT BACK-OFFPRESSURE CHAMBER FROM UPPER CYLINDER MORE THAN 1-1/4”.
7. If gas pressure still does not bleed off, back off Firing Head exactly 1-1/4” from Pressure Chamber and drivenail into bleeder hole in Pressure Chamber. POSITIVELY STAND CLEAR OF BLEEDER HOLE DURINGTHIS PROCEDURE.
8. CAUTION: ALL PESSURIZED GAS MUST BE BLED OFF BEFORE FURTHER DIASSSEMBLY IS BE-GUN. THE TWO HALVES OF THE TOOL WILL BLOW APART.
9. Unscrew and remove Firing Head. Unscrew and remove Pressure Chamber and Upper Cylinder.
10. Push Upper Piston out lower end of Upper Cylinder. Remove O-rings from Pressure Chamber, Upper Piston,and Firing Head.
Disassemble remainder of setting assembly components. Thoroughly remove power charge debris by washingall parts with kerosene. Apply light coat of oil to all parts to prevent rust from forming.
SIZE 20 WIRELINE SETTING TOOLASSEMBLY INSTRUCTIONS
PO
WE
R C
HA
RG
E
OILDAMPER
POWERCHARGE
BLEED VALVE
IGNITER
3-5/8" O.D. 1.50, 1.71, 2.12" O.D.
Model “BP” wireline pressure setting tools are compact tools insidewhich the ignition and burning of a pyrotechnic power charge (manufac-tured by TITAN SPECIALTIES, Pampa,Texas) produces gas pressurethat elongates the tool. This provides the stroke and force necessary toset and anchor conventional bridge plugs, packers, and cement retain-ers provided by various manufacturers. The tools feature pressure balanced top and bottom pistons to eliminatepresetting of the mentioned products caused by high hydrostatic wellpressure.
OPERATION: An electrically actuated high temperature rated igniter (also manufac-tured by TITAN SPECIALTIES) located at the upper end of the tool isignited and produces a flash flame which, in turn, ignites the power chargethat is located directly below the igniter. The power charge, which isconstructed of carefully controlled combustible elements, begins a slowburn lasting approximately 30 seconds. The resultant gas derived fromthe burning charge gradually builds to high pressure and causes the toolto elongate. The pressurized gas migrates down the center of the top piston and outinto an annular cavity formed between the top piston and connector sub.The pressure acting on this area drives the outside of the tool (consistingof top and bottom cylinders) downward while the top and bottom pistonsremain stationary. This motion anchors the bridge plug to the casing i.d.then pulls the shear stud of the bridge plug apart, freeing the setting toolfor removal from the well. An oil damper system is built into the tool to control the speed at whichthe tool strokes. As the tool elongates, this oil is forced through anannular orifice and out of the tool at a controlled rate and prevents thetool from stroking too fast, causing damage to the tool once the shearstud has parted. NOTE: IT IS MANDATORY THAT THE TOOL BE FILLED TO CAPACITYWITH OIL EACH USE OR DAMAGE TO THE TOOL WILL RESULT.Excess oil will be purged out automatically during assembly. Likewise,oil expansion caused by high well temperature during running will bepurged in the same manner. In wells where hydrostatic pressure is less than 10,000 psi, all toolsizes are available with manual bleeder valve assemblies. This valve pro-vides a safe, easy method of bleeding trapped gas pressure from the toolbefore disassembly is begun. When bottom hole pressures exceeding10,000 psi are to be encountered, the manual bleeder valve and its corre-sponding sub are replaced by a portless sub. Bleeding is then accom-plished by backing the firing head out of the setting tool. Both methodsof bleeding pressure are illustrated in the disassembly steps found laterin this manual.
MODEL “BP” WIRELINE SETTING TOOLS
COMPACT - SINGLE STAGE
3-5/8” O.D. “BP” SETTING TOOL
VENDOR POWER CHARGES AND IGNITERS FOR USE WITH THIS TOOL:
1. POWER CHARGES:TITAN SPECIALTIES, LTD. PT. NO. 6000-000-170-4OWEN OIL TOOLS, INC. PT. NO. JEC-5334-104 (HIGH TEMP)
2. IGNITERS:TITAN SPECIALTIES, LTD. PT. NO. 6035-000-050OWEN OIL TOOLS, INC. PT. NO. DET-5306-074
THREAD
WST-5125-142BLEEDER VALVE ASSY.BLEEDER WRENCH
WST-5125-146
23
24
22
21
3/8-24 NF
7
20LEFT HAND
1/4" HEX
PARTS LIST
TOOL TOTAL STROKE: 9.94 IN.
TOOL PISTON AREA: 5.26 IN.²
TOOL MAX. PULL: 55,000 LBS. AT 6.6 INCH STROKE
TOOL MAX. HYDROSTATIC PRESSURE: 10,000 P.S.I.
16.25
8.94
1.75
12.00
3.25
1.00
43.19
3.50
3.25
3.62
3
11
4
5
6
7
8
9
10
12
13
14
15
16
17
18
19
6
6
1 2
FILLWITHOIL
9.94"STROKE
METI REBMUNTRAP .QER NOITPIRCSED
1 101-5263-TSWPOT-LOOTGNITTES"PB".D.O"8/5-3-.YSSA
-.YSSAEGNAHCKCIUQ"4/1-3TIFOTNOITCENNOC42-6DNA,4,3SMETI.LCNI
2 201-5263-TSWPOT-LOOTGNITTES"PB".D.O"8/5-3-.YSSAGNIRIF01#EZISREKABTIFOTNOITCENNOC
42-7DNA5SMETI.LCNI-DAEH
*3 823-965N-000 1 .ORUD09-GNIR-O
4 021-5263-TSW 1 .YSSAEGNAHCKCIUQ"4/1-3TIFOT-BUSPOT
5 231-5263-TSW 1 DAEHGNIRIF01#EZISREKABTIFOT-BUSPOT
*6 233-965N-000 6 .ORUD09-GNIR-O
7 241-5215-TSW 1 42-02SMETI.LCNI-EVLAVREDEELB-.YSSA
*8 622-965N-000 2 .ORUD09-GNIR-O
*9 300-3035-250 1 raehs.sbl0056.xorppa-WERCSRAEHSSSARB
01 121-5263-TSW 1 BUSECIFIRO
11 521-5263-TSW 1 REDNILYCPOT
21 221-5263-TSW 1 NOTSIPPOT
*31 223-965N-000 2 .ORUD09-GNIR-O
41 621-5263-TSW 1 BUSROTCENNOC
*51 533-965N-000 1 .ORUD09-GNIR-O
61 721-5263-TSW 1 REDNILYCMOTTOB
71 031-5263-TSW 1 GNIRKCOL
81 821-5263-TSW 1 NOTSIPMOTTOB
91 131-5263-TSW 1 TUNKCOL
02 341-5215-TSW 1 EVLAVREDEELBROF-METS
12 441-5215-TSW 1 EVLAVREDEELBROF-TUNRENIATER
22 541-5215-TSW 1 EVLAVREDEELBROF-TAES
*32 312-965N-000 1 EVLAVREDEELBROF-.ORUD09-GNIR-O
*42 210-965N-000 1 EVLAVREDEELBROF-.ORUD09-GNIR-O
* 011-5263-TSW101-5263-TSWROF-°523-TIKGNIR-O
-42,32,51,31,9,8,6,3SMETI.LCNI
* 211-5263-TSW201-5263-TSWROF-°523-TIKGNIR-O
-42,32,51,31,9,8,6SMETI.LCNI
3-5/8” O.D. “BP’ SETTING TOOLAssembly Instructions
11 14 12
FILLWITHOIL
10
1. Screw Connector Sub (item 14) toeither end of Top Cylinder (item 11).
2. Place Top Piston (item 12), lower end first,inside Top Cylinder and Connector Sub.
3. Bump Top Piston fully closed insideTop Cylinder and Connector Sub.Bump on wooden block only.
fill reservoir with motor oil4. Turn tool upright and 5. Screw Orifice Sub
(item 10) to Top Cylinder.to bottom of threads.
6. Install Bleeder Valve (item 7) in Top Sub (item 4). Place Power Charge (open end up)inside Top Piston. Screw Top Sub to Top Piston. Do not allow oil to leak out of reservoir.
wrench on Top Sub and tightening Bottom Piston. Next, rotate Top Sub until the Shear Screw (item 9) can be installed into tapped8. Screw Bottom Piston (item 18) to Top piston. Wrench tighten the Top Sub, Top Piston, and Bottom Piston by holding backup
47
POWER CHARGE
16
7. Screw Bottom Cylinder (item 16) to Connector sub.
POWER CHARGE
hole of Orifice Sub and blind hole provided in Top Sub. Finally, install Igniter Assembly and 3-1/4" o.d. Quick Change Assembly .
18
POWER CHARGE
9
3-5/8” O.D. “BP” SETTING TOOLMin. & MAX. WEAR DIAMETERS
A-0-T-E, INC. WIRELINE PRESSURE SETTING TOOLS ARE CONSTRUCTED FROM HIGH QUALITY ALLOY STEELWITH TRACEABLE HEAT NUMBERS. MATERIAL HARDNESS IS ALSO CONTROLLED.
THE ILLUSTRATIONS SHOWN ABOVE LIST SUGGESTED CRITICAL MINIMUM AND MAXIMUM WEAR DIAMETERS.
TOP SUB
TOP PISTON
BOTTOM PISTONBOTTOM CYLINDER
CONNECTOR SUB
TOP CYLINDER
ORIFICE SUB
2.885MAX.
3-5/8"O.D.
2.885MAX.
3-1/2"O.D.
2.805MIN.
1.980MAX.
MIN.1.960
2.125"O.D.
3-1/2"O.D.
MAX.2.160
3-1/4"O.D.
MAX.3.135
2.860MIN.
1.240MIN.
1.263MAX.
2.860MIN.
2.860MIN.
3-5/8"O.D.
.493MIN.
BLEEDER STEM
BLEEDER SEAT
RETAINER NUT
MIN..917
.502MAX.
NOTE:
THE RETAINER, STEM, AND SEAT MUST BEREPLACED BEFORE 20 RUNS, OR EARLIER
IF CONDITIONS WARRANT.
1.71” O.D. “SHORTY” SETTING TOOL
#8-32 THREAD
THREAD
BLEEDER VALVE ASSY.
LEFT HAND
WST-2125-146BLEEDER WRENCH
21
WST-2125-142
20
19
18
16
171/8" HEX
22
PARTS LIST
6
WITHFILL
OIL
3
8
10
3
9
8
7
11
4
3
2
1
14
13
3
8
3
12
5
3
3.50
14.63
5.04
2.70
1.91
11.00
.50
11.56
50.84
6.36STROKE
METI REBMUNTRAP .QER NOITPIRCSED
1 100-8171-TSW-LOOTGNITTES"YTROHS".D.O"17.1-.YSSA
.D.O"61/7-1"OG"TIFOTNOITCENNOCPOT41-2SMETI.LCNI-DAEHGNIRIFERUSSERPHGIH
2 020-8171-TSW 1 BUSPOT
*3 612-965N-000 31 .ORUD09-GNIR-O
4 120-8171-TSW 1 REBMAHCREDWOP
5 820-8171-TSW 1 DETROPNON-BUSRAEHS
6 620-8171-TSW 1 NOTSIPPOT
*7 300-4035-250 1 raehs.sbl0032.xorppa-WERCSRAEHSSSARB
*8 511-965N-000 6 .ORUD09-GNIR-O
9 320-8171-TSW 1 BUSECIFIRO
01 420-8171-TSW 1 REDNILYCPOT
11 720-8171-TSW 1 BUSMEDNAT
21 520-8171-TSW 1 REDNILYCMOTTOB
31 030-8171-TSW 1 GNIRKCOL
41 920-8171-TSW 1 NOTSIPMOTTOB
* 010-8171-TSW100-8171-TSWROF-°523-TIKGNIR-O
-8,7,3SMETI.LCNI
100-8171-TSW.YSSANIDEDULCNITONTNEMPIUQELANOITPO
51 220-8171-TSW 1 EVLAVREDEELBROFDETROP-BUSRAEHS
61 241-5212-TSW 1 12-71SMETI-EVLAVREDEELB-.YSSA
71 341-5212-TSW 1 METS
81 441-5212-TSW 1 TUNRENIATER
91 541-5212-TSW 1 TAES
02 111-965N-000 1 .ORUD09-GNIR-O
12 600-965N-000 1 ORUD09-GNIR-O
22 641-5212-TSW HCNERWREDEELB
TOOL TOTAL STROKE: 6.36 IN.
TOOL PISTON AREA: 1.11 IN. ²
TOOL MAX. PULL: 13,000 LBS. AT 4.25 INCH STROKE
UNPORTED TOOL MAX. HYDROSTATIC PRESSURE: 15,000 P.S.I.
PORTED TOOL MAX. HYDROSTATIC PRESSURE: 10,000 P.S.I.
VENDOR POWER CHARGES AND IGNITERS FOR USE WITH THIS TOOL:
1. POWER CHARGES:TITAN SPECIALTIES, LTD. PT. NO. 6000-000-171-1SOWEN OIL TOOLS, INC. PT. NO. JEC-5302-041
2. IGNITERS:TITAN SPECIALTIES, LTD. PT. NO. 6035-000-050OWEN OIL TOOLS, INC. PT. NO. DET-5306-074
1.71” O.D. “SHORTY” SETTING TOOLMIN. AND MAX. WEAR DIAMETERS
SHEAR SUBMAX..693
BOTTOM CYLINDER
POWDER CHAMBER
1.360
MIN.1.360
MIN.
REF.1.25
MAX.1.385
TOP SUB
MIN.1.360
1.257MAX.
TANDEM SUB
MAX.1.385
MIN.
.693MAX.
(BOTH ENDS)
TOP CYLINDER
1.360
MAX.1.385
ORIFICE SUBMAX..697
1.363MIN.
MIN.1.363
TOP PISTON
.678MIN.
.678MIN.
BOTTOM PISTON
A-0-T-E, INC. WIRELINE PRESSURE SETTING TOOLS ARE CONSTRUCTED FROM HIGH QUALITY ALLOY STEELWITH TRACEABLE HEAT NUMBERS. MATERIAL HARDNESS IS ALSO CONTROLLED.
THE ILLUSTRATIONS SHOWN ABOVE LIST SUGGESTED CRITICAL MINIMUM AND MAXIMUM WEAR DIAMETERS.
6
WITHFILL
OIL
3
8
10
3
9
8
7
11
4
3
2
1
14
13
3
8
3
12
5
3
5.00
16.00
7.88
2.51
1.63
10.75
.50
11.69
55.94
6.36STROKE
24
26
25
23
PARTS LIST
TOOL TOTAL STROKE: 6.36 IN.
TOOL PISTON AREA: .859 IN.²
TOOL MAX. PULL: 13,000 LBS. AT 4.25 INCH STROKE
UNPORTED TOOL MAX. HYDROSTATIC PRESSURE: 15,000 P.S.I.
PORTED TOOL MAX. HYDROSTATIC PRESSURE: 10,000 P.S.I.
METI REBMUNTRAP .QER NOITPIRCSED
1 100-0051-TSW-LOOTGNITTES"YTROHS".D.O"05.1-.YSSA
.D.O"61/7-1"OG"TIFOTNOITCENNOCPOT41-2SMETI.LCNI-DAEHGNIRIFERUSSERPHGIH
2 020-0051-TSW 1 BUSPOT
*3 312-965N-000 31 .ORUD09-GNIR-O
4 120-0051-TSW 1 REBMAHCREDWOP
5 820-0051-TSW 1 DETROPNON-BUSRAEHS
6 620-0051-TSW 1 NOTSIPPOT
*7 300-4035-250 1 raehs.sbl0032.xorppa-WERCSRAEHSSSARB
*8 311-965N-000 6 .ORUD09-GNIR-O
9 320-0051-TSW 1 BUSECIFIRO
01 420-0051-TSW 1 REDNILYCPOT
11 720-0051-TSW 1 BUSMEDNAT
21 520-0051-TSW 1 REDNILYCMOTTOB
31 030-0051-TSW 1 GNIRKCOL
41 920-0051-TSW 1 NOTSIPMOTTOB
* 010-0051-TSW100-0051-TSWROF-°523-TIKGNIR-O
-8,7,3SMETI.LCNI
100-0051-TSW.YSSANIDEDULCNITONTNEMPIUQELANOITPO
51 220-0051-TSW 1 EVLAVREDEELBROFDETROP-BUSRAEHS
61 241-5212-TSW 1 12-71SMETI-EVLAVREDEELB-.YSSA
71 341-5212-TSW 1 METS
81 441-5212-TSW 1 TUNRENIATER
91 541-5212-TSW 1 TAES
02 111-965N-000 1 .ORUD09-GNIR-O
12 600-965N-000 1 ORUD09-GNIR-O
22 641-5212-TSW HCNERWREDEELB
32 040-0051-TSWGNITTES.D.O"61/11-1OT-TIK.TPADA-.YSSA
62,52,42SMETI-SRETPADAGNITTESLOOT
42 140-0051-TSW 1 EVEELSRETPADA
52 240-0051-TSW 1 DORRETPADA
62 030-8171-TSW 1 GNIRKCOL
BLEEDER VALVE ASSY.WST-2125-146BLEEDER WRENCH
WST-2125-142
#8-32 THREAD
THREADLEFT HAND
21
20
19
18
16
171/8" HEX
22
VENDOR POWER CHARGES AND IGNITERS FOR USE WITH THIS TOOL:
1. POWER CHARGES:TITAN SPECIALTIES, LTD. PT. NO. 6000-000-171-1SOWEN OIL TOOLS, INC. PT. NO. JEC-5302-041
2. IGNITERS:TITAN SPECIALTIES, LTD. PT. NO. 6035-000-050OWEN OIL TOOLS, INC. PT. NO. DET-5306-074
1.5” O.D. “SHORTY” SETTING TOOL
1.5” O.D. “SHORTY” SETTING TOOL
1.172
ORIFICE SUBMAX.
MIN.
.572
SHEAR SUBMAX..568
MIN.1.172
POWDER CHAMBER
REF.
MAX.
1.18
1.197
TOP SUB
MIN.1.172
MAX.
BOTTOM CYLINDER
1.197MAX.
BOTTOM PISTON
1.175MIN.
TANDEM SUBMAX..568
TOP CYLINDER
1.172
(BOTH ENDS)MIN.
TOP PISTON
MIN..553
MIN.1.175
1.197MAX.
MIN..553
A-0-T-E, INC. WIRELINE PRESSURE SETTING TOOLS ARE CONSTRUCTED FROM HIGH QUALITY ALLOY STEELWITH TRACEABLE HEAT NUMBERS. MATERIAL HARDNESS IS ALSO CONTROLLED.
THE ILLUSTRATIONS SHOWN ABOVE LIST SUGGESTED CRITICAL MINIMUM AND MAXIMUM WEAR DIAMETERS.
MIN. AND MAX. WEAR DIAMETERS
2-1/8 O.D. MULTI-STAGE SETTING TOOL
BLEEDER WRENCHWST-2125-146
LEFT HAND
WST-2125-142BLEEDER VALVE ASSY.
22
19
20
21
THREAD
#8-32 THREAD
181/8" HEX
17
PARTS LIST
FILL WITH
3
5.00
15.88
14
15
16
12
13
3
387.13
1.06
16.06
3
11
4
10
9
1.06
16.06
STROKE10.36
3
11
4
1
10
OIL
9
23.50
2.63
1.88
7
8
4
5
17
3
24.0 6
3
METI REBMUNTRAP .QER NOITPIRCSED
1 101-5212-TSW-LOOTGNITTESEGATS-ITLUM.D.O"8/1-2-.YSSAHGIH.D.O"61/7-1"OG"TIFOTNOITCENNOCPOT
71-2SMETI.LCNI-DAEHGNIRIFERUSSERP
2 021-5212-TSW 1 BUSPOT
*3 222-965N-000 81 .ORUD09-GNIR-O
*4 212-965N-000 6 ORUD09-GNIR-O
*5 300-4035-250 1 raehs.sbl0032.xorppa-WERCSRAEHSSSARB
6 121-5212-TSW 1 REBMAHCREDWOP
7221-5212-TSW
1EVLAVREDEELBROFDETROP-BUSRAEHS
231-5212-TSW )EVLAVREDEELBON(DETROPNU-BUSRAEHS
8 321-5212-TSW 1 BUSECIFIRO
9 421-5212-TSW 2 REDNILYCPOT
01 521-5212-TSW 2 NOTSIPPOT
11 621-5212-TSW 2 BUSROTCENNOC
21 721-5212-TSW 1 REDNILYCMOTTOB
31 821-5212-TSW 1 NOTSIPMOTTOB
41 921-5212-TSW 1 GNIRKCOL
51 031-5212-TSW 1 TNIOPKAEW.SBL000,25-TUNESAELERYTEFAS
61 131-5212-TSW 1 RETPADAMOTTOB
71 241-5212-TSW 1 22-81SMETI-EVLAVREDEELB-.YSSA
81 341-5212-TSW 1 METS
91 441-5212-TSW 1 TUNRENIATER
02 541-5212-TSW 1 TAES
*12 111-965N-000 1 ORUD09-GNIR-O
*22 600-965N-000 1 ORUD09-GNIR-O
32 641-5212-TSW HCNERWREDEELB
* 011-5212-TSW101-5212-TSWROF-°523-TIKGNIR-O
-22,12,5,4,3SMETI.LCNI
TOOL TOTAL STROKE: 10.36 IN.
TOOL PISTON AREA: 3.6 IN.²
TOOL MAX. PULL: 30,000 LBS. AT 6.91 INCH STROKE
UNPORTED TOOL MAX. HYDROSTATIC PRESSURE: 15,000 P.S.I.
PORTED TOOL MAX. HYDROSTATIC PRESSURE: 10,000 P.S.I.
TOP SUB
MAX.1.258
1.737MIN.
POWDER CHAMBER
1.760MAX.
REF.1.63
TOP PISTON(2-REQ'D.)
.870MIN.
SHEAR SUB
MIN.1.737
.885MAX.
ORIFICE SUB
.911MAX.
TOP CYLINDER
CONNECTOR SUB(2-REQ'D.)
MAX..885
1.737MIN.
(BOTH ENDS)
1.760MAX.
(2-REQ'D.)
BOTTOM CYLINDER
1.760MAX.
BOTTOM PISTON
.870MIN.
1.737MIN.
M1N.1.737
(BOTH ENDS)
A-0-T-E, INC. WIRELINE PRESSURE SETTING TOOLS ARE CONSTRUCTED FROM HIGH QUALITY ALLOY STEELWITH TRACEABLE HEAT NUMBERS. MATERIAL HARDNESS IS ALSO CONTROLLED.
THE ILLUSTRATIONS SHOWN ABOVE LIST SUGGESTED CRITICAL MINIMUM AND MAXIMUM WEAR DIAMETERS.
2-1/8 O.D. MULTI-STAGE SETTING TOOLMIN. AND MAX. WEAR DIAMETERS
PARTS LIST
TOOL TOTAL STROKE: 10.45 IN.
TOOL PISTON AREA: 2.22 IN.²
TOOL MAX. PULL: 13,000 LBS. AT 6.91 INCH STROKE
UNPORTED TOOL MAX. HYDROSTATIC PRESSURE: 15,000 P.S.I.
PORTED TOOL MAX. HYDROSTATIC PRESSURE: 10,000 P.S.I.
LEFT HAND
BLEEDER VALVE ASSY.
THREAD
#8-32 THREAD
BLEEDER WRENCHWST-2125-146
24
WST-2125-142
23
22
21
20
18
191/8" HEX
METI REBMUNTRAP .QER NOITPIRCSED
1 101-8171-TSW-LOOTGNITTESEGATS-ITLUM.D.O"17.1-.YSSA
.D.O"61/7-1"OG"TIFOTNOITCENNOCPOT61-2SMETI.LCNI-DAEHGNIRIFERUSSERPHGIH
2 020-8171-TSW 1 BUSPOT
*3 612-965N-000 81 .ORUD09-GNIR-O
*4 511-965N-000 6 .ORUD09-GNIR-O
*5 300-4035-250 1 raehs.sbl0032.xorppa-WERCSRAEHSSSARB
6 121-8171-TSW 1 REBMAHCREDWOP
7 820-8171-TSW 1 DETROPNON-BUSRAEHS
8 320-8171-TSW 1 BUSECIFIRO
9 421-8171-TSW 2 REDNILYCPOT
01 521-8171-TSW 2 NOTSIPPOT
11 621-8171-TSW 2 BUSROTCENNOC
21 721-8171-TSW 1 REDNILYCMOTTOB
31 821-8171-TSW 1 NOTSIPMOTTOB
41 030-8171-TSW 1 GNIRKCOL
51 031-8171-TSW 1 TNIOPKAEW.SBL000,52-TUNESAELERYTEFAS
61 131-8171-TSW 1 RETPADAMOTTOB
* 011-8171-TSW101-8171-TSWROF-°523-TIKGNIR-O
-32,22,5,4,3SMETI.LCNI
101-8171-TSW.YSSANIDEDULCNITONTNEMPIUQELANOITPO
71 220-8171-TSW 1 EVLAVREDEELBROFDETROP-BUSRAEHS
81 241-5212-TSW 1 32-91SMETI-EVLAVREDEELB-.YSSA
91 341-5212-TSW 1 METS
02 441-5212-TSW 1 TUNRENIATER
12 541-5212-TSW 1 TAES
22 111-965N-000 1 .ORUD09-GNIR-O
32 600-965N-000 1 ORUD09-GNIR-O
42 641-5212-TSW HCNERWREDEELB
92 38. 3
3
5 0. 1
16.00
14
61
51
13
12
3
31. 1
15.56
3
11
4
10
9
STRO EK
31. 1
15.56
0 41 . 5
3
11
4
1
OIL
01
FILL W T I H
9
91. 1
72. 0
4
8
5
7 71
81
3
9.52
.503
3
6
2
1.718” O.D. MULTI-STAGE SETTING TOOL
1.718” O.D. MULTI-STAGE SETTING TOOLMIN. AND MAX. WEAR DIAMETERS
TOP SUB
MAX.1.257
1.360MIN.
POWDER CHAMBER
1.385MAX.
REF.1.25
TOP CYLINDER
1.385MAX.
(2-REQ'D.)
CONNECTOR SUB(2-REQ'D.)
MAX..693
1.360MIN.
(BOTH ENDS)
SHEAR SUB
MIN.1.360
.693MAX.
BOTTOM CYLINDER
1.385MAX.
TOP PISTON(2-REQ'D.)
BOTTOM PISTON
ORIFICE SUB
.697MAX.
1.360MIN.
MIN..678
1.363MIN.
1.363MIN.
.678MIN.
A-0-T-E, INC. WIRELINE PRESSURE SETTING TOOLS ARE CONSTRUCTED FROM HIGH QUALITY ALLOY STEELWITH TRACEABLE HEAT NUMBERS. MATERIAL HARDNESS IS ALSO CONTROLLED.
THE ILLUSTRATIONS SHOWN ABOVE LIST SUGGESTED CRITICAL MINIMUM AND MAXIMUM WEAR DIAMETERS.
3-1/4” O.D. MULTI-STAGE SETTING TOOL
PARTS LIST
TOOL TOTAL STROKE: 14.8 IN.
TOOL PISTON AREA: 7.66 IN.²
TOOL MAX. PULL: 72,000 LBS. AT 9.0 INCH STROKE
PORTED TOOL MAX. HYDROSTATIC PRESSURE: 10,000 P.S.I.
WST-5125-146BLEEDER WRENCH
26
LEFT HAND
3/8-24 THREAD
THREAD
BLEEDER VALVE ASSY.
25
WST-5125-142
23
24
22
20
211/4" HEX
22.28
18
17
5
16
14
15
6
5
13
7.42
5
12
126.56
1.50
14.89STROKE
22.28
22.00
1.50
OIL
1
6
5
13
12
5
FILL WITH
6
7
9
5
37.0
5.00
2.41
3.16
8
5
202.00
19
3
4
2
10
11
11
METI REBMUNTRAP .QER NOITPIRCSED
1 100-0523-TSW-LOOTGNITTESEGATS-ITLUM.D.O"4/1-3-.YSSA
KCIUQ.D.O"4/1-3"OG"TIFOTNOITCENNOCPOT52-2SMETI.LCNI-.YSSAEGNAHC
2 020-0523-TSW 1 EVLAVREDEELBROFDETROP-BUSPOT
*3 823-965N-000 1 .ORUD09-GNIR-O
*4 233-965N-000 1 ORUD09-GNIR-O
*5 133-965N-000 81 ORUD09-GNIR-O
*6 523-965N-000 6 ORUD09-GNIR-O
*7 300-4035-250 1 raehs.sbl0032.xorppa-WERCSRAEHSSSARB
8 120-0523-TSW 1 REBMAHCREDWOP
9 220-0523-TSW 1 BUSRAEHS
01 320-0523-TSW 1 BUSECIFIRO
11 420-0523-TSW 2 REDNILYCPOT
21 520-0523-TSW 2 NOTSIPPOT
31 620-0523-TSW 2 BUSROTCENNOC
41 720-0523-TSW 1 REDNILYCMOTTOB
51 820--0523-TSW 1 NOTSIPMOTTOB
61 920-0523-TSW 1 GNIRKCOL
71 030-0523-TSW 1 TNIOPKAEW.SBL000,021-TUNESAELERYTEFAS
81 130-0523-TSW 1 RETPADAMOTTOB
91 131-5263-TSW 1 TUNKCOL
02 241-5215-TSW 1 52-12SMETI-EVLAVREDEELB-.YSSA
12 341-5215-TSW 1 METS
22 441-5215-TSW 1 TUNRENIATER
32 541-5215-TSW 1 TAES
*42 312-965N-000 1 ORUD09-GNIR-O
*52 210-965N-000 1 ORUD09-GNIR-O
62 641-5215-TSW HCNERWREDEELB
* 010-0523-TSW100-0523-TSWROF-°523-TIKGNIR-O
-52,42,7,6,5,4,3SMETI.LCNI
MULTI-STAGE SETTING TOOLSAssembly Instructions
11 11
2. Screw CONNECTOR SUBS (11) into BOTTOM CYLINDER and one of TOP CYLINDERS.Make wrench tight. Wrench only on wrenching areas provided. Do not wrench on pistonsanywhere except in knurled areas.
3. Join TOP CYLINDER / TOP PISTON unit to CONNECTOR SUB / TOP PISTON unit.Make wrench tight.
1. Install o-rings then lubricate o-rings and threads. Slide TOP PISTONS (10) inTOP CYLINDERS (9). Install RELEASE NUT and BOTTOM ADAPTER (15 & 16)to BOTTOM PISTON (13) then install this unit in BOTTOM CYLINDER (12).
10 9 1213 1615
2
8. Screw TOP SUB (2) to POWDER CHAMBER wrench tight. Check IGNITOR by first removing ground wire from contact springthen checking resistivity (51 ohms) with blasting galvanometer. Next, wrap ground wire around case of ignitor body then placeignitor in firing head. Tool is now assembled. Attach appropriate firing adapter, collar locator, and setting adapters.
6 POWER CHARGE 7
7. Install BLEEDER VALVE ASSY. (17) if used. Screw POWDER CHAMBER (6) to SHEAR SUB (7).Install POWER CHARGE. Make sure open end of power charge is facing up.
17
5. Remove tool from vise. Bump tool (view A) completely closed(on wooden block). Next, turn tool upright then fill TOP CYLINDERwith motor oil until oil level reaches groove at lower end of thread.
Install ORIFICE SUB (8). Excess oil will purge as sub is screwed in.
7 5 16
6. Return tool to vise. Make ORIFICE SUB (8) wrench tight to TOP CYLINDER. Screw SHEAR SUB (7) to TOP PISTON.Hold back-up wrench on BOTTOM ADAPTER (16) and tighten SHEAR SUB which will ensure all inside connectionsare tight. Rotate SHEAR SUB clockwise until SHEAR SCREW holes align then install SHEAR SCREW (5).
8
8
View BView A
4. Join remaining TOP CYLINDER / TOP PISTON unit to CONNECTOR SUB / TOP PISTON unit.Make wrench tight.
PRESSURE BLEEDING LOCATIONS
1-1/2” - 2-1/8” O.D. SETTING TOOLS
A-O-T-E, Inc. wireline pressure setting tools in o.d. sizes 1-1/2” through 2-1/8” do not containa Baker style manual bleeder valve assembly (A-O-T-E pt. no. WST-2125-142) except whenspecifically ordered.
Two locations for bleeding pressure from tools less manual bleed valves are illustrated in drawing“A”. The preferred method of bleeding pressure is to hold wrench on “GO” 1-1/2” o.d. high pressurefiring adapter while turning the setting tool counter clockwise. Pressure will begin to bleed as soon asthe lower o-ring on the firing adapter is uncovered. Ample threads are provided on the firing adapter.Should a bridge occur and pressure stops bleeding, screw the tool clockwise then begin the procedureagain.
The alternate method shown in drawing “A” is accomplished by holding wrench on shear sub (see parts list)while turning the top cylinder counter clockwise. The top piston will back out of shear suband pressure will begin to bleed. Again, if a bridge occurs screw the tool clockwise then begin the procedureagain.
An indication that most of pressure has safely bled off is when the tool partially closes. This indicates that thetrapped compressed atmosphere in bottom cylinder is overcoming what little gas pressure remains of the
power charge.
A. TOOLS WITHOUT MANUAL
BLEEDER VALVE ASSY. BLEEDER VALVE ASSY.
B. TOOLS WITH MANUAL
WST-2125-146BLEEDER WRENCH
BLEED LOCATION
(ALTERNATE)
WST-2125-142BLEEDER VALVE ASSY.
SHEAR SUB
TOP PISTON
TOP CYLINDER
"GO" TYPE 1-7/16" O.D. HIGH
PRESSURE FIRING ADAPTER
BLEED LOCATION
(PREFERRED)
BLEED LOCATION
(ALTERNATE)