#11162m ottage arbor assembly instructions instru… · dura-trel, inc. ~ po box 122, sheboygan...
TRANSCRIPT
Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
#11162M Cottage arbor
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED:
Drill with #2 Phillips Bit or Phillips Screwdriver Hammer or Mallet
ARBOR SIDE PANEL ASSEMBLY (Refer to Drawing 1) (Make 2) On clean flat surface, lay the two 2 x 2 x 65" posts with screw pilot holes facing up and routed holes for 7/8 x 1 ½ x 29 ¾" cross rails facing each other. Insert one of the 7/8 x 1 ½ x 29 ¾" top/bottom rails into the bottom routed holes in post, then insert the center rails. Slide the 1 x 1 x 58 ¼" vertical rails through the routed holes of the cross rails and insert the last top/bottom cross rail into the top of the posts guiding the 1 x 1's into the top rail. Firmly press the posts together so that all cross rails are completely inserted in the posts. Fasten the posts and cross rails with the ¾" screws and snap the screw caps over the screw heads. ARBOR TOP ASSEMBLY (Refer to Drawing 2) Using the two bent arbor tops, with 1 x 1" routed holes facing each other, insert the 1 x 1 x 29 ¾" square rail between tops. Make sure 1 x 1's are completely in both bent arbor top pieces and fasten with the 1 ¼" screws and snap screw caps over screw heads. Set the flared ends of the arbor top assembly onto the assembled side panels. The screw caps on the side panels should face the outside of the completed arbor unit. The arbor is now ready for installation (See Ground Anchor Hardware Bag). If you encounter missing or defective parts, please contact manufacturer direct at toll free
# below.
Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
PACKING LIST
PARTS CONTAINED:
#11162M cottage Arbor (mocha)
QTY. PART NO. PART DESCRIPTION BOX NO. 2 40202-M65000L 2 x 2 x 65" LEFT POST 1 2 40202-M65000R 2 x 2 x 65" RIGHT POST 1 4 47815-M29750 ⅞ x 1½ x 29¾" TOP/BOTTOM RAIL 1
10 47815-M29751 ⅞ x 1½ x 29¾" CENTER RAIL 1
2 40202-M50000 2 x 2 x 50" ARBOR TOP 2 6 60101-M58000 1 x 1 x 58" RAIL 2 8 60101-M29750 1 x 1 x 29¾" TOP CROSS RAIL 2 1 HWBAG-M22GAA GROUND ANCHOR HARDWARE BAG 2 Hardware Bag Includes:
12 7HDWR-K8034 ¾" KAPPET SCREW 2 8 7HDWR-K8125 1 ¼" KAPPET SCREW 2
20 7HDWR-MK8000 KAPPET SCREW CAP 2 COTTAGE ARBOR INSTRUCTIONS
NOTE: Some parts may be packed inside of others.
If you encounter missing or defective parts, please contact manufacturer direct at toll free # below.
Option 1 (soft ground) Slide one 16” steel L-channel ground anchor into bottom of each post. Slide ground anchor up to bottom cross rail. Using two 1” self-tapping white-head screws per post, screw post to ground anchor (figure 1). When fastening, use one screw per side where ground anchor meets post. For added support fasten screws with at least two inches vertically between them. Option 2 (hard ground) Measure distances between posts and mark ground accordingly. Pound 16” steel L-channel ground anchors into ground according to measurements and basic layout (figure 2), leaving about 4 inches of ground anchor exposed. When pounding into ground, use block of wood to prevent ground anchor from bending. Slide arbor over ground anchors. Using two 1” self-tapping white-head screws per post screw post to ground anchor (figure 1). When fastening, use one screw per side where ground anchor meets post. For added support fasten screws with at least two inches vertically between them. Option 3 (permanent installation) Measure distances between posts and mark ground accordingly. Dig holes 12” deep according to measurements and basic layout (figure 2). Fill with cement and place 16” steel L-channel ground anchors in wet cement. Be sure that ground anchors are straight and in accordance with measurements of arbor posts. Allow cement to dry. NOTE: There is very little room for error with this installation method. Slide arbor over ground anchors. Using two 1” self-tapping white-head screws per post screw post to ground anchor (figure 1). When fastening, use one screw per side where ground anchor meets post. For added support fasten screws with at least two inches vertically between them.
FIGURE 1 Ground Anchor
Assembly
FIGURE 2 Ground Anchor
Basic Installation Layout
2” sq. post arbor ground anchor
Assembly & installation Instructions
Description Qty
16” L-channel Ground Anchor 4
1” Self-tapping White-head Screws 8
Parts List: