xsf xlite 10s plate connected square truss r • •.xsftruss.com we recycle • the loads outlined...

300 CMH Road • Sulphur Springs , Texas 75482 903.438.1100 • www.xsftruss.com

We Recycle

• The loads outlined in the above table are for the Xtreme Structures and Fabrication XLITE 10T Plate Connected Triangular Truss.• This truss has 1 1/2" diameter chords and 5/8" diameter steel bolts.•This truss is also available in a 10" square truss.

XSF XLITE 10T PLATE CONNECTED TRIANGULAR TRUSSLoads Calculated Considering Truss Weight (Beam Configuration)

XSF XLITE 10S PLATE CONNECTED SQUARE TRUSSLoads Calculated Considering Truss Weight (Beam Configuration)

5 524 2620 0.04 1310 0.03 984 0.04 655 0.04 546 0.0410 260 2601 0.35 1300 0.28 976 0.36 650 0.33 542 0.3515 172 2581 1.18 1290 0.95 963 1.20 645 1.12 538 1.1920 71 1429 1.60 896 1.60 525 1.60 377 1.60 296 1.6025 35 866 2.00 543 2.00 318 2.00 228 2.00 179 2.0030 18 552 2.40 346 2.40 203 2.40 145 2.40 114 2.40

XSF XLITE 10S PLATE CONNECTED SQUARE TRUSSLoads Calculated Considering Truss Weight (Beam Configuration)

Uniformly Distributed Center Point Loads Third Point Loads Quarter Point Loads Fifth Point Loads

SpanLength

(ft) UDL (plf)

Total Load (lbs)

Calc. Defl. (in)

Load(lbs)

Calc. Defl. (in)

Calc. Defl. (in)

Calc. Defl. (in)

Calc. Defl. (in)

Load(lbs)

Load(lbs)

Load(lbs)

• The loads outlined in the above table are for the Xtreme Structures and Fabrication XLITE 10S Plate Connected Square Truss.• This truss has 1 1/2" diameter chords and 5/8" diameter steel bolts.•This truss is also available in a 10" triangular truss.

XLITE 10" Square Truss

XLITE Utility Platforms

XLITE Base Plates

XLITE 10" Triangle Truss

• Each4'x8'deckweighs136LBS.

• Standardaluminumconstruction

• Fixedheightsupportlegsare availablewithfootpadsor lockingcasters

• Blackpowdercoatingavailable

• Greatforchoirriseruseinschoolsandworshipfacilities

• Platformsareratedfor60LB/SQ.FT.


We Recycle

Our high quality truss is available with three connection options: Fork Ended, Plated and Aluminum Fork Ended. We inventory a large selection of straight and circular trussing here in the Dallas area at XSF, as well as multiple locations across the U.S. at our Master Stocking Distribu-tors listed on the back cover. Our book-end and center-pivot hinges all include heavy duty stainless steel shafts and high quality oil-impregnated bronze bushings.

Thefollowingisalistofstandardavailabletrussingsizes:

12"x12" Utility12"x18" Utility16"x16" Utility20.5"x20.5" Utility30"x20.5" Heavy Duty30"x30" Super Duty36"x30" Super Heavy Duty26"x30" DHPRT18.5"x26" SHPRT

Plated

HingesCorner Blocks

Steel Fork Ended

Aluminum Fork Ended

Standard Product TrussXSF 12" x 12" PLATED UTILITY TRUSS

Maximum Superimposed Gravity Loads

Main Chords are 2.0" OD x 1/8" wall aluminum. Diagonals are 1.0" OD x 1/8" wall aluminum. Bolt plate connection for use with 5/8" bolts.

Visitusonlineatwww.XSFtruss.comforafulllistoftrussloadtablesavailablefordownload.

XSF 12" x 12" STEEL FORK ENDED UTILITY TRUSSMaximum Superimposed Gravity Loads

Main Chords are 2.0" OD x 3/16" wall aluminum. Diagonals are 1.0" OD x 1/8" wall aluminum. Fork ended connection for use with 3/4" Clevis Pins.

XSF 12" x 12" ALUMINUM FORK ENDED UTILITY TRUSSMaximum Superimposed Gravity Loads


Center Point Loads Third Point Loads Quarter Point Loads Fifth Point LoadsUniformly Distributed

Span (ft) UDL (plf)Total Load

(lbs)Max Defl.

(in) Load (lbs)Max Defl.




(in)

2084969450237135764428

104209690675047403375228015401120

0.040.290.691.161.672.002.332.62

1028848483377237519311436894561

1@1@1@1@1@1@1@1@

0.060.230.550.931.532.002.172.20

52123636239617811244843570419

2@2@2@2@2@2@2@2@

0.050.300.671.191.672.002.332.67

3474242416521188892604409281

3@3@3@3@3@3@3@3@

0.050.280.641.101.672.002.332.52

260617311198848681475321234

4@4@4@4@4@4@4@4@

0.050.250.591.011.622.002.332.65

510152025303540


We Recycle

Standard Product Truss

XSF 16" x 16" STEEL FORK ENDED UTILITY TRUSSMaximum Superimposed Gravity LoadsXSF 12" x 18" STEEL FORK ENDED UTILITY TRUSS


Main Chords are 2.0" OD x 3/16" wall aluminum. Diagonals are 1.0" OD x 1/8" wall aluminum. Fork ended connection for use with 3/4" Clevis Pins.Main Chords are 2.0" OD x 3/16" wall aluminum. Diagonals are 1.0" OD x 1/8" wall aluminum. Fork ended connection for use with 3/4" Clevis Pins.


XSF 16" x 16" PLATED UTILITY TRUSSMaximum Superimposed Gravity Loads

XSF 12" x 18" PLATED UTILITY TRUSSMaximum Superimposed Gravity Loads

Main Chords are 2.0" OD x 1/8" wall aluminum. Diagonals are 1.0" OD x 1/8" wall aluminum. Bolt plate connection for use with 5/8" bolts.Main Chords are 2.0" OD x 1/8" wall aluminum. Diagonals are 1.0" OD x 1/8" wall aluminum. Bolt plate connection for use with 5/8" bolts.





(lbs)Max Defl.





(in)

2084969450237135764428

104209690675047403375228015401120

0.040.290.691.161.672.002.332.62

1028848483377237519311436894561

1@1@1@1@1@1@1@1@

0.060.230.550.931.532.002.172.20

52123636239617811244843570419

2@2@2@2@2@2@2@2@

0.050.300.671.191.672.002.332.67

3474242416521188892604409281

3@3@3@3@3@3@3@3@

0.050.280.641.101.672.002.332.52

260617311198848681475321234

4@4@4@4@4@4@4@4@

0.050.250.591.011.622.002.332.65

510152025303540





(lbs)Max Defl.





(in)

2186105163333522214593613928

5101520253035404550

109301051094956700555043503255244017551400

0.020.160.500.841.371.882.332.673.003.33

1093367994750335027422179186415381118799

1@1@1@1@1@1@1@1@1@1@

0.030.170.400.671.101.522.142.673.003.07

5466509933712513197416341201903656519

2@2@2@2@2@2@2@2@2@2@

0.030.210.480.851.331.922.332.673.003.33

364434002325167513431089862647471372

3@3@3@3@3@3@3@3@3@3@

0.030.200.460.801.271.792.332.673.003.33

2733242816851197968778660509370292

4@4@4@4@4@4@4@4@4@4@

0.030.180.430.721.171.642.282.673.003.33


We Recycle

XSF 20.5" x 20.5" STEEL FORK ENDED UTILITY TRUSSMaximum Superimposed Gravity Loads


XSF 20.5" x 20.5" PLATED UTILITY TRUSSMaximum Superimposed Gravity Loads



XSF 20.5" x 20.5" ALUMINUM FORK ENDED UTILITY TRUSSMaximum Superimposed Gravity Loads




(lbs)Max Defl.





(in)

244111898074432951931451057353

5101520253035404550

1220511890121058860737557905075420032852650

0.010.110.360.631.051.432.042.533.003.33

12210899162844439363528972481210718291618

1@1@1@1@1@1@1@1@1@1@

0.020.130.300.510.831.151.622.072.693.26

610559454460332926182173180715801213975

2@2@2@2@2@2@2@2@2@2@

0.020.140.370.651.011.461.992.593.003.33

40703964307622201781144812221054870699

3@3@3@3@3@3@3@3@3@3@

0.020.130.350.600.961.361.882.423.003.33

305229732230158512831035879753649549

4@4@4@4@4@4@4@4@4@4@

0.020.130.320.550.891.241.732.222.873.33





(lbs)Max Defl.





(in)

2095995690493384250190137109825034

51015202530354045505560

104759950

10350986096007500665054804905410027502040

0.010.050.190.420.811.101.581.962.592.992.952.94

1047699588161576347313765323827422398205414021044

1@1@1@1@1@1@1@1@1@1@1@1@

0.010.080.230.390.640.891.251.602.082.462.502.52

52384979518143223406282323592057175815411052783

2@2@2@2@2@2@2@2@2@2@2@2@

0.010.070.250.500.781.131.532.002.533.053.053.05

3492331934542882231718821596137111851027701522

3@3@3@3@3@3@3@3@3@3@3@3@

0.010.070.240.470.741.051.451.872.402.862.872.88

2619248925902058167013441147979851754584435

4@4@4@4@4@4@4@4@4@4@4@4@

0.010.060.220.420.680.961.341.712.212.693.013.01

Center Point Loads Third Point Loads Quarter Point Loads Fifth Point LoadsUniformly DistributedSpan Description

Span (ft)Number ofSections UDL (plf)

Total Load(lbs)

Max Defl.(in) Load (lbs)




Max Defl.(in)

1943673293160995425

194301346087906400495032401750

0.080.420.941.672.623.183.22

1361567344407322024871643877

1@1@1@1@1@1@1@

0.080.340.761.372.152.682.76

971950503305241518651233658

2@2@2@2@2@2@2@

0.100.430.971.722.683.293.28

64793367220416101244822438

3@3@3@3@3@3@3@

0.100.400.901.602.513.093.11

4859240515741150888685365

4@4@4@4@4@4@4@

0.090.360.821.472.313.253.24

10203040506070

1234567

XSF 26" x 18.5" SINGLE-HUNG PRE-RIGGED FORK ENDED ALUMINUM TRUSSMaximum Superimposed Gravity Loads

XSF 30" x 20.5" ALUMINUM FORK ENDED UTILITY TRUSSMaximum Superimposed Gravity Loads


XSF30"x20.5"trussisalsoavailablewithSteelorAluminumForkEndedconnections,contactusformoreinformation.

XSF26"x18.5"trussisalsoavailablewithSteelorAluminumForkEndedconnections,contactusformoreinformation.


We Recycle


XSF 26" x 30" DOUBLE-HUNGPLATED PRE-RIGGED TRUSS



XSF 26" x 30" DOUBLE-HUNG PRE-RIGGED ALUMINUM FORK ENDED TRUSS





(lbs)Max Defl.





(in)

2091993686491380248186134104826147

51015202530354045505560

10455993010290982095007440651053604680410033552820

0.010.050.190.420.811.101.581.952.563.063.674.00

1045699368131574146803732316826982308205517381608

1@1@1@1@1@1@1@1@1@1@1@1@

0.010.080.230.390.640.891.261.602.092.533.163.69

522849685151430633702799230820241693154212331044

2@2@2@2@2@2@2@2@2@2@2@2@

0.010.070.250.500.781.131.532.002.533.133.674.00

3485331234342871229218661561134911411028861749

3@3@3@3@3@3@3@3@3@3@3@3@

0.010.070.230.470.741.051.451.872.402.933.594.00

2614248425762050165213331122964819734618574

4@4@4@4@4@4@4@4@4@4@4@4@

0.010.060.220.430.690.961.341.722.222.703.343.92

STAGEMAKER® SM20

STAGEMAKER® concert hoists are designed to handle stage and theatrical equipment and enable the safe and accurate positioning of speakers, lighting systems, stage sets, and sceneries. The features and options of STAGEMAKER® concert hoist make it the best choice for a demanding customer. Its low weight makes it ideal for touring events. The hoist's compact size permits it to fit inside truss structures. Its quietness makes it ideal for operation during performances, even in theaters. The CE mark and CSA c/us certification ensures the quality process. Contact us for pricing and availability.

STAGEMAKER® SM10 Variable Speed

STAGEMAKER® SM5

XSF26"x30"double-hungpre-riggedtrussisalsoavailablewithSteelForkEndedconnections,contactusformoreinformation.


We Recycle

Ground Support SystemsRoof Systems

• Fork End or Plated connections available• Single or Double Reeved pulley configurations• 12"x12", 16"x16" and 20.5"x20.5" Towers available• Pivoting Outrigger for placement flexibility• Braced Stabilizer for maximum resistance to overturning• Headblocks include stainless steel shafts and custom bearings• 6" diameter levelling pads with stainless steel hardware• Powder coating available in any color

Available in 24"x24" and 36"x36" sizes. Securely bolts to truss sizes from 10"x10" up to 20.5"x20.5"

Available in 24"x24" and 36"x36" sizes. Securely bolts to truss sizes from 10"x10" up to 20.5"x20.5"

Our motto at XSF is “Not all roof systems are created equal.” We work with our clients to design a roof system that will meet their needs regardless of the size or shape of the system. Preliminary design and layouts are provided at no additional cost to the customer when purchasing a roof system. So if it is a standard 40' x 40' roof that you need, no problem. If your roof system includes 20 towers in an unusual shape, PA wings and is permanently installed on uneven ground, no problem. Custom roof systems at off-the-shelf pricing is what we do.

The XSF heavy duty ground support system (shown this page) offers a number of benefits over standard ground support systems and is capable of roof system trim heights of up to 60 feet. We also offer a light duty ground support system (not shown) for applications that may not require the strength of our heavy duty system.

Steel Base Plate

Aluminum Base Plates


We Recycle

Design & Fabrication of custom applications is our specialty. We pride ourselves on quick response and timely quotes for custom projects of any size. Technical design, utilizing the latest graphic software allows us to furnish 3D concept design drawings for approval. We work closely with our third party engineering firms to ensure that your design meets standard codes and safety regulations. Regardless of the size or require-ments of your project, we can work with you to design and fabricate a custom truss that will meet your needs. No project is too large or too small for our team at XSF.

Custom Truss

DisneyonIce

Metallica EdgeFest

OzzyOsbourne

SeaWorld

GeminiSLV DefLeppard

GeorgeThorogood

MetropolisMall

TacomaDome


We Recycle

Truss & Rigging Accessories

Fall ProtectionGotcha Rescue KitXtreme Structures and Fabrication is proud to offer the SpanSet Gotcha Fall Protection Kit to our customers.

Work at height can be a hazardous activity. The SpanSet Gotcha kit is a unique solution to a problem faced by all workers at height who use PPE for protection against falls. Whereas most rescue provision has focused on the more extreme activities carried out at height, the Gotcha kit is designed for tradesmen who use common items of fall protection. In the event of a fall, a swift recovery from a harness suspension situation is essential.

Gotcha Rescue kit will work effectively with conscious or unconscious casualties. It is a quick rescue from the point of safety, the rescue can be carried out by a single person, no cutting is required and you can raise or lower the casualty to the nearest point of safety.

Trussing Accessories

Rigging Accessories We carry a variety of trussing accessories and replacement parts including:

• Bolts and Clevis Pins• Truss Casters• Shank Hooks/Couplers• Baseplate Pins• PRT Guide Rods• Sleeve Block Caster • Steel and Aluminum Base Plates • Pipe Battens • And much more

XSF provides a full line of rigging accessories to complement our truss line. In addition to our line of XSF accessories, our inventory includes a full line of products from SpanSet and Lightsource. Call us for pricing and availability.

SpanSet Stage Sling

SpanSet’s Stage Sling is a double -walled dark covered sling, designed specifically for the entertainment and theatrical industry. This sling is lightweight, soft and pliable, and ideal for inconspicu-ous suspension of stage and lighting equipment. The steel core within this sling eliminates the need for steel back-up safety lines. Each sling comes with a velcro opening that allows the user to properly inspect the steel core. Spanset is the original manufacturer of round slings and is the first name in safety.

Air Wall Hangers

Beam Clamps

Mega Couplers

Half Couplers

Quad Couplers

Mega ClawsTruss Protectors

Mega Truss Picks

Pinch Blocks/Grapples

Square CouplersMini-Clamps


We Recycle

Circle & Oval Truss

XSF truss circles come in standard sizes of 10', 12', 15', 20', and go up to 80' in diameter. Portions of these circles can be used to create ovals, arcs or vertical arches. Truss sizes for circles include any plated truss size we offer ranging from 12"x12" Utility truss up to 36"x36" truss or larger. We form roll our aluminum tubes in house and can fabricate any custom size circle or oval to meet your needs.

Array Towers

Heavy Duty Line Array Tower

Our heavy duty tower is a free standing support structure that has been designed and engineered to support 4,400 pounds of weight and resist 45mph wind loads. The tower mast and legs consist of 16"x16" fork end truss and extends up to a maximum overall height of 31'-0".Water ballast tanks are provided with the system to prevent overturning. Screw jacks are provided in the legs for adjustability on uneven surfaces.

XLITE Tower Structure

Our XLITE tower structure is a free standing support structure designed and engineered to support 1,000 pounds of weight in indoor applications. The structure masts consist of our efficient 10" XLITE Truss and measure up to an overall height of 23'-0". The channel legs are fabricated from high grade aluminum alloy and provide adjustability for uneven surfaces. No additional ballasting components are required.

Arch Line Array Tower

The arch line array tower structure is a free-standing support structure that has been designed and engineered to support 2,200 pounds of weight in indoor applications. The mast and outriggers consist of 12"x12" plated utility circle truss. The mast hinges down and back on itself to create a com-pact portable unit. The tower is provided with or without a tower lifter, depending on height and weight requirements. The tower is shipped assembled and ready to hinge up into position.

Light Duty Line Array Tower

Our light duty tower is a free standing support structure that has been designed and engineered to support 1,300 pounds of weight and resist 45mph wind loads. The tower mast and legs consist of 12"x12" plated Utility Truss. This is a cost effective tower that measures a maximum overall height of 28'-6" and requires no additional ballasting components. Screw jacks are provided in the legs for adjustability on uneven surfaces.


We Recycle

Parasol offers a whole new dimension of lighting design and gives light-ing designers an unprecedented level of additional control and options in the deployment of automated lighting fixtures. XSF is proud to be the exclusive manufacturer of Parasol Para™Cart and KLR™ systems.

Parasol has developed a system consisting of self-propelled, wirelessly controlled vehicles, which travel along pre-determined guideways. Each vehicle or “ParaCart” is utterly independent of the other. Vehicles can move together in groups, or sub-groups, or individually. The Kinetic Light Ring, or KLR, enables the designer to move the source point of automated fixtures along a pre-defined path. Lighting designers will no longer be restricted to light sources that stem from one static point. Now, Parasol will move entertainment lighting into a whole new dimension!

From concept to design to a functioning lighting system, XSF has been an integral part of developing Parasol products. Contact us for more information, pricing and availability of the Parasol product line.

Parasol™ Advanced Lighting Systems

KineticLightRing3DDesign

ParaCartsatPirates of the Caribbean 4WorldPremier KineticLightRing,GeminiSLV,Dallas


We Recycle

Truss Use and Inspection

Shownaboveisa20.5x20.5UtilityTrussthatshowsthetypeofdamagethatmaybecausedbyaforklift.Notethatthediagonalontheleft,theinternaldiagonalinthemiddle,andtheverticalmemberontherighthaveallbeenclearlymarkedwithred andhotpinktapeatthedamagedlocations.Thetrusswas immediatelyremovedfromserviceandsenttousforrepair.

It is our recommendation that inspection procedures should be performed on any truss that is in use or is scheduled for use. Truss inspection procedures should be performed by an individual competent in the use and inspection of trusses. It is the responsibility of the owner/user to inspect the truss or to hire competent individuals to inspect the truss.

Truss components such as chords and diagonals should be inspected for abrasions, punctures, dents or bent members. Each truss should also be checked to make sure all of the components are in place and have not been removed such as internal diagonals that are often damaged by fork lift use.

Truss bolt plate connections should be checked for cracked welds and/or plates as well as elongation or deformation of the bolt holes. Pinned connections (including inline aluminum or steel connections) should be checked for abrasion, elongation or deformation of pin holes, and deformation of pins.

All welds on the truss should be visually inspected for cracks or abrasions. Alternate means of inspecting welds such as dye penetrant testing or weld x-ray technology may be used. However, these types of weld inspections must be performed by a professional welding inspector and often times can be much more costly that simply repairing or replacing the truss.

The truss should be reviewed as a whole for camber, squareness and/or bending. In other words if the truss will not sit flat on a flat surface it may have been overstressed in use with no apparent damage on the truss members.

It is our recommendation that complete records be kept on file of the annual inspections.

Upon completing the inspection of a truss, should the truss show damage as listed above, the truss shall be taken out of service immediately. Clearly mark the truss unsafe for use with red tape, a sign, or some other means that will leave no question as to the condition of the truss. If the truss is not repairable it is our recommendation that the truss be cut into pieces to avoid accidental use in the future which could endanger lives. If the truss is repairable it should be set aside and discontinued from use until properly repaired.

All repairs made to a truss shall be performed by a qualified manufacturer’s representative or someone approved by the manufacturer. Records of the repair shall be kept on file by the owner along with the serial number and description of the truss.

Please contact us if you have questions concerning truss inspections or if you would like to have one of our representatives on site to inspect your truss. We offer full inspection services with records of the inspections provided to the owner along with our recommendations. We also offer truss inspection training and seminars which can be provided on site with your staff inspecting your truss under our supervision.

Truss InspectionThe proper use and handling of aluminum truss can significantly increase the lifespan of any truss. Always avoid unnecessary abrasive or impact damage to the truss such as dragging or dropping the truss if at all possible. Always use enough people to ensure that the truss is properly handled when moving truss by hand. Dollies should also be used when moving truss to prevent dropping or dragging the truss members.

When transporting truss by truck, take precautions to properly package and secure the truss and other items around the truss properly which will prevent rubbing and/or bouncing that could cause serious damage.

Always use extreme caution when moving trusses with a fork lift and ensure that the person operating the machinery is properly trained and certified in the use of a fork lift. The steel forks of the lift can easily damage the aluminum members in a truss if not used properly. If at all possible place the forks under the truss to avoid damaging the diagonals and internal members.

When handled properly aluminum truss is a relatively maintenance free product with a long life expectancy.

Fall Protection on TrussIt is our recommendation that fall protection always be used when working in overhead situations. Many times when working up at trim height there are not convenient lifelines or proper fall protection anchorage points within existing facilities. Other times the structures may be outdoors and the only option a rigger has while working is to clip off to the aluminum truss. There are dozens of other scenarios in which the aluminum truss may be required as a fall protection anchor. When working in these situations several important issues must be addressed prior to anchoring yourself to the truss.

First, is the truss capable of supporting the stress incurred from a fall given it's current load application? In other words, if a span of truss is already supporting a considerable amount of load is there enough capacity left in the truss to safely arrest a fall. After all, what good would the truss be to a rigger as an anchor point if the shock loading from the fall only brought the truss down on top of them? Load tables are provided for industry standard trusses by reputable manufacturers. Refer to these tables to ensure that there is a minimum of 1,000 pounds

of additional capacity available in the truss before climbing up and anchoring to a truss. To re-emphasize this very important point, if the truss is not capable of supporting it's current load AND another 1,000 pounds it is our recommendation that workers do not anchor to it as a means of fall protection. Second, is the system as a whole capable of supporting the stress incurred from a fall? In this situation there may be an instance where an outdoor roof system is loaded unsym-metrically and does not have the additional capacity required to arrest a fall. For instance, often times PA Wings are used on outdoor roof systems and the towers onstage of the PA Wings may already be loaded up to capacity. The lighting truss spanning cross stage, where a rigger might be required to work before or between shows, could potentially have the capacity to support a fall, but the tower it is sitting on does not. This is certainly a rare situation, but we present this scenario to raise awareness about using systems for fall protection. In the end it may be much safer to use a lift rather than climb on the system. Third, in the event you find yourself anchored to a truss it is important that the anchor point is at an appropriate location. An appropriate location on a typical truss is at a panel point. The panel point, also referred to as a node, is the location where two or more members are welded together on the truss. A good example of a panel point is the location where the two diagonals are welded to the chord of the truss.

TrussUseWhen attaching 2 trusses together always ensure that the con-nections are secure prior to lifting or loading the truss. This includes tightening all bolts and/or securing fork end clevis pins with R-clips. Once the trusses are connected together the span acts as a single truss. There are no special requirements to be met at or around the connections concerning load distribution or rigging.

When rigging a truss always ensure that the rig point is located at a panel point or node. This includes rigging to support mo-tors or rigging to structures above as well as lighting, sound or video applications loaded below the truss. The truss has been designed so that rigging may be applied either to the top or the bottom of the truss as long as the rigging is at a panel point.

Truss Handling

The information provided above is certainly not all encompassing and is provided only as a guideline to raise awareness about the use of fall protection on aluminum truss and truss systems.

Master Stocking Distributors Reed Rigging

4400 W. 45th StreetChicago, Illinois 60632773.521.7333www.reedrigging.com

Jax Logistics145 S. Glenoaks Blvd. Suite 434Burbank, CA 91502951.733.2741www.jaxlogistics.com

C&J EnterpriseP.O. Box 13182Baltimore, MD 21203443.790.0431www.candjonline.com

Gemini Stage Lighting10218 Miller RoadDallas, TX 75238214.341.4822geminilightsoundvideo.com

Atlanta Rigging Systems1270 Tacoma DriveAtlanta, GA 30318404.355.4370www.atlantarigging.com

Mountain Light Company4920 Fox Street Suite BDenver, CO 80216303-572-9700www.mountain-light.com

We currently have one Master Stocking Distributor territory available in the USA. If you are located in the Pacific Northwest and would like to be an official XSF Distributor contact us for more details! Distributorships are also available in Canada and Mexico.

XSF is a premier provider of standardized truss sizes, as well as custom stages, roof systems, hardware, rigging, risers, platforms, and exhibit components.

Founded in 2002 and based in Sulphur Springs, TX, we are proud to also offer products through our distributors in Los Angeles, Denver, Chicago, Dallas, Baltimore, and Atlanta. Our products are safe, reliable, user friendly and always the highest quality available. With innovative vision and superior customer service, Xtreme Structures and Fabrication is ready to meet your trussing and staging needs.

Xtreme Quality. Xtreme Service. Xtreme Innovation.

300CMHRoadSulphurSprings,Texas75482

903.438.1100www.xsftruss.com

We Recycle

xsf xlite 10s plate connected square truss r • •.xsftruss.com we recycle • the loads outlined...

Documents