x200 series variable frequency drive | industrial eco ...analog frequency monitor, analog current...

1-/3-phase 200V class

Standard Specifications

3

General Specifications

3-phase 400V class

002SFEF2002NFU2002LFRF2

0.2(1/4)0.50.51.4


0.4(1/2)1.01.02.6

005SFEF2--

0.55(3/4)1.11.23.0


0.75(1)1.51.64.0

011SFEF2--

1.1(1.5)1.92.05.0


1.5 (2)2.82.97.1


2.2(3)3.94.110.0

-037LFU2

037LFRF23.7(5)

6.36.6

15.9

-55LFU2

055LFRF25.5(7.5)

9.69.9

24.0

-075LFU2

075LFRF27.5(10)

12.713.332.0

150% for 60 sec.3-phase (3-wire) 200 to 240V (corresponding to input voltage)

SFEF: 1-phase 200 to 240V+10%, -15%, 50/60Hz ±5%NFU: 1-/3-phase 200 to 240V+10%, -15%, 50/60Hz ±5%LFU/LFRF: 3-phase 200 to 240V+10%, -15%, 50/60Hz ±5%

Self-cooling Force ventilation

0.80.80.8

3.11.8

5.83.4

6.7-

9.05.2

11.2-

16.09.3

22.513.0

-20.0

-30.0

-40.0

-SFEF2-NFU2/LFU2-LFRF2

1.00.90.9

1.5--

1.51.51.1

2.4--

2.42.32.2

2.52.42.4

-2.32.4

-4.24.2

-4.24.2

Rated input voltage (V)

Rated input current(A)

European VersionUS VersionJP Version

Model X200-

Output Ratings

Input Rating

Enclosure *4Cooling method

Applicable motor size, 4-pole kW(HP) *1

Rated capacity

Rated output current (A) *2Overload capacity(output current)Rated output voltage (V)

230V240V

SFEF2NFU2/LFUF2/LFRF2

Weight (kg)

Zero phase Reactor

-SFEF2-NFU2/LFU2/LFRF2-LFRF2

Integrated EMC filter

Model X200-004HFEF2004HFU2

004HFRF20.4(1/2)

1.01.21.5

007HFEF2007HFU2

007HFRF20.75(1)

1.72.02.5

015HFEF2015HFU2

015HFRF21.5 (2)

2.63.13.8

022HFEF2022HFU2

022HFRF22.2(3)

3.84.55.5

030HFEF2--

3(4)5.46.47.8

040HFEF2040HFU2

037HFRF24(5)5.97.18.6

055HFEF2055HFU2

055HFRF25.5(7.5)

9.010.813.0

075HFEF2075HFU2

075HFRF27.5(10)

11.113.316.0

150% for 60 sec.3-phase (3-wire) 380 to 480V (corresponding to input voltage)

3-phase 380 to 480V +10%, -15%, 50/60Hz±5%

IP20Self-cooling Force ventilation

1.51.41.5

2.0 3.3 5.0 7.0 10.0 11.0 16.5 20.0

Output Ratings

Input Rating

Enclosure *4Cooling method

Applicable motor size, 4-pole kW(HP) *1

Rated capacity

Rated output current (A) *2Overload capacity(output current)Rated output voltage (V)

European VersionUS VersionJP Version

2.32.22.3

2.42.32.4

2.42.32.4

2.4-

2.4

2.42.32.4

4.24.24.2

4.24.24.2

Rated input voltage (V)Rated input current (A)

400V480V

-HFEF2-HFU2-HFRF2

Weight (kg)

Zero phase Reactor

Integrated EMC filter

Item General SpecificationsLine-to-line sine wave pulse-width modulation (PWM) control0.5 to 400HzDigital command :±0.01%, Analog command±0.4% (25 ±10˚C)Digital: 0.1Hz, Analog: (max frequency)/1000V/f control,V/f variable (constant torque, reduced torque)0.01 to 3000 sec. (linear, sigmoid), two-stage accel./decel.100%/6Hz2.0 to 12kHzOver-current, over-voltage, under-voltage, overload, overheat, ground fault at power-on, input over-voltage, external trip, EEPROM error,CPU error, USP error, Termister error, Driver error, Safety stop10kohm input impedance, sink/source logic selectableFW(Forward), RV(Reverse), CF1-CF4(Multispeed command), JG(Jogging), DB(External DC braking), SET(Second motor constants setting),2CH(Second accel./decel.), FRS(Free-run stop), EXT(External trip), USP(Unattended start protection), SFT(Software lock), AT(Analog inputselection), RS(Reset), PTC(Thermistor input) *8, STA(3-wire start), STP(3-wire stop), F/R(3-wire fwd./rev.), PID(PID On/Off), PIDC(PID reset),UP/DWN(Remote-controlled accel./decel.) , UDC(Remote-controlled data clearing), OPE(Operator control), ADD(ADD frequency enable), F-TM(force terminal mode), RDY(quick start enable),S-ST(Special-Set 2nd Motor Data),EMR(Safety stop), NO(Not selected)27V DC 50mA max open collector output, 1 terminals 1c output 250V AC/30V DC 2.5A relay (AL0, AL1, AL2 terminals)RUN(run signal), FA1(Frequency arrival type 1 - constant speed), FA2(Frequency arrival type 2 - over-frequency), OL(overload advancenotice signal), OD(Output deviation for PID control), AL(alarm signal), DC(Wire brake detect on analog input), FBV(PID Second StageOutput), NDC(ModBus Network Detection Signal), LOG(Logic Output Function), ODC(Option Card Detection Signal), LOC(Low load)0 to 10V DCAnalog Frequency monitor, analog current monitor4-digits 7 segment LEDsParameter setting, output frequency, output current, scaled value of output frequency, trip history, I/O terminal condition, outputvoltage. Rotation direction, PID Feedback, RON time, Power-on time.Power, Alarm, Run, Prg, Hz and A Potentiometer, RUN, STOP/RESET, UP, DOWN, FUN and STR keysUp and Down keys / Value settings or analog setting via potentiometer on operator keypad0 to 10 V DC, 4 to 20 mARS485 interface (Modbus RTU)Run key / Stop key (change FW/RV by function command)FW Run/Stop (NO contact), RV set by terminal assignment (NC/NO), 3-wire input availableRS485 interface (Modbus RTU)-10 to 50˚C(carrier derating required for aambient temperature higher than 40°C), no freezing-20 to 65˚C20 to 90% RH5.9mm/s2 (0.6G) 10 to 55HzAltitude 1,000 m or less, indoors (no corrosive gasses or dust)AVR (Automatic Voltage Regulation), V/f characteristic selection, accel./decel. curve selection, frequency upper/lower limit, 16 stagemultispeed, PID control, frequency jump, external frequency input bias start/end, jogging, cooling fan On/Off, trip history etc.

Remote operator with copy function (SRW-0EX), input/output reactors, DC reactors, radio noise filters, braking resistors, braking units, LCR filter, communication cables (ICS-1, 3)

Control

Input terminal

Output signal

Operator

Operation

Environment

Other functions

Coating colorOptions

Control methodOutput frequency range *5Frequency accuracy *6Frequency setting resolutionVoltage/Frequency CharacteristicAcceleration/deceleration timeStarting torque *7Carrier frequency range

Protective functions

Specification

Functions

Intelligent output terminal

Analog output terminal

Display

Status LED Interface

Frequency setting

FW/RV Run

Operating temperatureStorage temperatureHumidityVibrationLocation

Operator keypadExternal signalSerial portOperator KeypadExternal signalSerial port

Function

SpecificationFunctionSpecification

Function

Note 1: The applicable motor refers to Hitachi standard 3-phase motor (4-pole). When using other motors, care must betaken to prevent the rated motor current (50/60 Hz) from exceeding the rated output current of the inverter.

Note 2: The output voltage decreases as the main supply voltage decreases (except when using the AVR function). Inany case, the output voltage cannot exceed the input power supply voltage.

Note 3: The braking torque via capacitive feedback is the average deceleration torque at the shortestdeceleration (stopping from 50/60 Hz as indicated). It is not continuous regenerative braking torque. The average decel torque varies with motor loss. This value decreases when operating beyond 50 Hz.If a large regenerative torque is required, the optional regenerative braking resistor should be used.

Note 4: The protection method conforms to JEM 1030.Note 5: To operate the motor beyond 50/60 Hz, consult the motor manufacturer

for the maximum allowable rotation speed.Note 6: The output frequency may exceed the maximum frequency setting

(A004 or A204) for automatic stabilization control.Note 7: At the rated voltage when using a Hitachi standard 3-phase, 4pole

motor.Note 8: Only terminal 5 is assignable the PTC (thermistor) function.

Blue

EN61800-3 category C1 filter

IP20

-

EN61800-3 category C2 filter

Built-in

Built-in

--HFEF2-HFU2/HFRF2-HFRF2

Specification

Dimensions

4

143(

5.63

)

155(

6.10

)

80(3.15)67(2.64)

5(0.20)

5(0.20)

6(0.

24)

4.4(

0.17

)93

(3.6

6)

13(0

.51)

2.6(

0.10

)

Wall

143(

5.63

)

155(

6.10

)

80(3.15)

67(2.64)

5(0.20)

5(0.20)

6(0.

24)

4.4(

0.17

)10

7(4.

21)

27(1

.06)

2.6(

0.10

)

Wall

176(

6.93

)

189(

7.44

)

110(4.33)

98(3.86)

5(0.20)

5(0.20)

6(0.

24)

4.4

(0.1

7)12

8(5.

04)

28(1

.10)

2.6(

0.10

)

176(

6.93

)

189(

7.44

)

5(0.20)

5(0.20)

6(0.

24)

4.4

(0.1

7)15

5(6.

10)

55(2

.17)

6(0.

24)

Wall

WallWall

WallWall

98(3.86)

Wall

110(4.33)

Air Intake

011SFEF2,007HFEF2,HFU2:without FAN

Exhaust

X200-002SFEF2, NFU2, LFRF2

X200-005SFEF2 X200-007SFEF2,NFU2 X200-004HFEF2,HFU2, HFRF2

X200-055~075LFU2,LFRF2 X200-055~075HFEF2,HFU2,HFRF2 X200-011SFEF2 X200-015～022SFEF2, NFU2 X200-037LFU2 X200-007~040HFEF2, HFU2 X200-015~037LFRF2 X200-007~037HFRF2

X200-004SFEF2, NFU2, LFRF2

180(7.09)164(6.46)

235(

9.25

)

250(

9.84

)

2-φ6(0.24)

4.4(

0.17

)

165(

6.50

)

6(0.24)

143(

5.63

)

155(

6.10

)

80(3.15)

67(2.64)

5(0.20)

5(0.20)

6(0.

24)

4.4

(0.1

7)13

0(5.

12)

50(1

.97)

2.6(

0.10

)

X200-007LFRF2

[Unit: mm(inch)]Inches for reference only

Operation and Programming

5

(1) or the value previously monitored is displayed.



(2)The motor runs at the frequency set by the potentiometer. (3)The motor stops.

(2)Function code appears. (3) appears.

(5) appears. (6)Preset value is displayed. (7)Newly set value is displayed.(8)Returns to and the setting is complete.

(4) or the code number set in the end of last setting is displayed.

Poweron

Power on

Power on

Press until appears.

Pressto set desired value.

Press

until

appears.

Press key.

Press key. Press key.

Press keyto store the value.

*To run the motor, go back tomonitor mode or basic setting mode.

*Pressing key

for a while and back to

Press key to stop the motor.Press key and turn the potentiometer clockwise.

Press key. Press key.

(2)Function code appears. appears.(4)Output current value is displayed.

Press

until appears.

1. Setting the maximum output frequency

2. Running the motor(by potentiometer)

3. Monitoring output current value

(3)

(Output frequency monitor)

RS-485 communication/operator selection switch

Safety stop ON/Off switch

SW7

SW8

ON

OFF

485

OPE

Operation / Terminal Functions

6

Hardware switches

Terminal DescriptionTerminal Symbol

L1 / N

+1+-U/T1 V/T2 W/T3

L1 L2 L3/N

SFEF2

NFU2, LFU2, LFRF2

+1+-U/T1 V/T2 W/T3

L1 / N

L1 L2 L3/N

SFEF2

NFU2,LFU2

R/L1 S/L2 T/L3HFEF2,HFU2, HFRF2

Screw Diameter and Terminal Width

Terminal arrangement

Control circuit terminalsTerminal arrangement

! "

#

Note 1:The standard keypad OPE (OPE-SRmini) can be used either the switch is set to 485 or OPE.Note 2:Input terminal selection (EMR) cannot be chosen from an operaator. If the slide switch SW8 is turned ON, it

divides automatically and is attached.

Terminal function

SW7

SW8

RS-485communication/key padselection switch

Safety stop ON/OFF

Switch symbol Switch Name Switch Name Description

Select communication connector distination. *1

485

OPE [default]

RS-485 communicaiton via Modbus protocol

Keypad (option)

Select frequency and run command input source.

The SW8 is for the Safety signal input. If you turn this DIP switchON, the inverter is ready to receive Safety signal from the dedicatedterminal #3. Inverter shuts off the output by means of pure hardwarewhen a signal is given to the terminal. Each signals related to this Safety input must be in accordance withthe norm. Additionally, the logic input terminal assign will bechanged automatically if the SW8 is made ON.

L1,L2,N/L3

U/T1,V/T2,W/T3

+1,++ -

Main power supply input terminals

Inverter output terminals

DC reactor connection terminals

External braking unit connection terminals

Ground connection terminal

Terminal Symbol Terminal Name

Model Screw diameter (mm)

002 - 004NFU2/SFEF2

002-007LFRF2

007- 022NFU2, 037LFU2

005 - 022SFEF2

015-037LFRF2

004- 040HFU2/HFEF2

004-037HFRF2

055- 075LFU2/LFRF2/HFU2/HFEF2/HFRF2

M3.5

M4

M5

Terminal width W (mm)

7.1

9.2

12

-

Terminal name Description Ranges and Notes

Input/monitorsignals

AML

P24PCS

54

3

2

1

Freqencysetting

Output signals

11

CM2

Relayoutput

AL2

AL1

AL0

H

O

OI

L

+10V analog reference

Analog input, voltage

Analog input, current

Common for inputs

Intelligent (programable) output terminals, selection from:RUN(run signal), FA1(Frequency arrival type 1 -constant speed), FA2(Frequency arrival type 2 -over-frequency), OL(overload advance noticesignal), OD(Output deviation for PID control), AL(alarm signal), DC(Wire brake detect on analog input), FBV(Feedback voltage comparison),NDc(Network Disconnection), LOG(Logic operation result), ODC(Option Card Detection signal), LOC(Low Load Detection).

Open collector outputL level at operation (ON)27V DC, 50mA max.

Common for intelligent output terminals

10V DC, 10mA max

0 to 10V DC, input impedance10kohm

4 to 20mA DC,input impedance 250ohm

-

Voltage analog outputCommon for inputs+24V for logic inputsIntelligent input common

0 to10V DC, 1mA max.-

24V DC, 30mA (do not short to terminal L)-

Intelligent (programable) input terminals, selection from:FW(Forward), RV(Reverse), CF1-CF4(Multispeed command), JG(Jogging), DB(External DC braking), SET(Second motor constants setting),2CH(Second accel./decel.), FRS(Free-run stop), EXT(External trip), USP(Unattended start protection), SFT(Software lock), AT(Analog inputselection), RS(Reset), PTC(Thermistor input), STA(3-wire start), STP(3-wire stop), F/R(3-wire fwd./rev.), PID(PID On/Off), PIDC(PID reset),UP/DWN(Remote-controlled accel./decel.), UDC(Remote-controlled data clearing), OPE(Operator control), ADD(Frequency setpoint), F-TM(Force terminal enable), RDY(Quick start enable), S-ST(Special-Set 2nd Motor Data), EMR(Safety stop) or NO(Not selected).

-

SWP24

1-5

Operated by closing switch.(Input logic is selectable)

+ - + -

Assign [AT] for input terminal to selecting frequency source from voltage or current.

(1kΩ-2kΩ) DC0-10VInput inpedance 10kΩ

DC4-20mAInput inpedance 250Ω

VR

H O OI L H O OI L H O OI L

AC250V 2.5A (Resistive load)0.2A (cos =0.4)

DC30V 3.0A (Resistive load)0.7A (cos =0.4)

(minimum) AC100V 10mADC 5V 100mA

! "

#$%& '(( ! "

Function List

7

Monitoring and main profile parameters

A Group: Standard functions

: Allowed[ X: Not allowed ]Lo Hi

The parameter tables in this chapter have a column titled "Run Mode Edit." An Ex mark x means the parameter cannot be edited; a Checkmark means the parameter can be edited. The table example to the right contains two adjacent marks "x ". These two marks (that canalso be "xx" or " ") correspond to low-access or high-access levels to Run Mode edits (note Lo and Hi in column heading).

: Allowed[ X: Not allowed ]

Function Code Name Range Default UnitRun mode edit

Monitor

Main ProfileParameters

F001F002F202F003F203F004

d001d002d003d004

d005

d006

d007d013d016d017d018d080d081d082d083d102d104

Output frequency monitorOutput current monitorRotation direction monitorProcess variable, PID feedback monitor

Intelligent input terminal status

Intelligent output terminal status

Scaled output frequency monitorOutput voltage monitorCumulative operation RUN time monitorCumulative power-on time monitorCooling fin temperature monitorTrip counterTrip monitor 1Trip monitor 2Trip monitor 3DC bus voltage monitorElectronic themal monitorOutput frequency settingAcceleration time (1) settingAcceleration time (2) settingDeceleration time (1) settingDeceleration time (2) settingKeypad Run key routing

----

-

-

-----------

HzA--

-

-

-Vhrhr˚C

events---V%

----

-

-

-----------

0.0/start freq. to 400.00.01 to 99.99/100.0 to 999.9/1000. to 3000.0.01 to 99.99/100.0 to 999.9/1000. to 3000.0.01 to 99.99/100.0 to 999.9/1000. to 3000.0.01 to 99.99/100.0 to 999.9/1000. to 3000.00(Forward)/01(Reverse)

0.010.010.010.010.000

Hzsecsecsecsec-

Expanded functions

A--b--C--H--P--

A Group: Standard functionsb Group: Fine-tuning functionsC Group: Intelligent terminal functionsH Group: Motor constants functionsP Group: Expansion Card Functions

5 4 3

ONOFF

2 1

AL

ONOFF

11

e.g. :1,2 : ON 3,4,5: OFF

e.g. :11 : ON AL : OFF

----

-

-

-----------

X

Basic setting

A001A201A002A202A003A203A004A204

Frequency source settingFrequency source setting, 2nd motorRun command source settingRun command source setting, 2nd motorBase frequency settingBase frequency setting, 2nd motorMaximum frequency settingMaximum frequency setting, 2nd motor

00(Keypad potentiometer)/01(Control terminal)/02(Function F001 setting)/03(RS485)/10(Calculation result)

01(Control terminal)/02(Run key on keypad)/03(RS485)

30 to maximum freq.30 to maximum freq.30 to 40030 to 400

0101010150.50.50.50.020.00.00.

100.018.

0.00.00.00.00.00.00.00.00.00.0

0.0

100.0000001.80.010.00.00000

100.100.100.0.50.00.

0.001

0000020260.60.60.60.020.00.00.

100.018.

0.00.05.010.015.020.030.040.050.060.0

0.0

100.0000001.80.010.00.00000

100.100.000.50.00.

0.001

0000020260.60.60.60.020.00.00.

100.018.

0.00.00.00.00.00.00.00.00.00.0

0.0

100.0000001.80.010.00.00000

100.100.100.0.50.00.

0.001

----HzHzHzHz-HzHz%%--HzHzHzHzHzHzHzHzHzHz

Hz

Hz---%%%%--%%-HzsecHzsec-

XXXXXXXXXXXXXXX

XXX

XX

XXXXXX

XXXXXXXX

XX

XX

Analog input setting

A005A011A012A013A014A015A016

[AT] selection[O]-[L] input active range start frequency[O]-[L] input active range end frequency[O]-[L] input active range start voltage[O]-[L] input active range end voltage[O]-[L] input start frequency enableExternal frequency filter time constant

02(O/VR)/03(OI/VR)/04(O)/05(OI)0.0 to maximum freq.0.0 to maximum freq.0 to 1000 to 10000(use set value)/01(use 0 Hz)1 to 17

Multi-speed andjogging

A020A220A021A022A023A024A025A026A027A028 A029-A035A038A039A041A241A042A242A043A243A044A244A045A245A051A052A053A054A055A056

Multi-speed frequency setting (0)Multi-speed frequency (2nd), setting 2nd motorMulti-speed frequency setting (1)Multi-speed frequency setting (2)Multi-speed frequency setting (3)Multi-speed frequency setting (4)Multi-speed frequency setting (5)Multi-speed frequency setting (6)Multi-speed frequency setting (7)Multi-speed frequency setting (8)

Multi-speed frequency setting (9-15)

Jog frequency settingJog stop modeTorque boost selectTorque boost select 2nd motorManual torque boost valueManual torque boost value, 2nd motorManual torque boost frequency adjustmentManual torque boost frequency adjustment, 2nd motorV/f characteristic curve selectionV/f characteristic curve selection, 2nd motorV/f gain settingV/f gain setting, 2nd motorDC braking enableDC braking frequency settingDC braking wait timeDC braking force during decelerationDC braking time for decelerationDC braking / edge or level detection for [DB] input

0.00/start freq. to 9.9900(free-run stop)/01(deceleration and stop)/02 (DC braking)00(Manual)/01(Automatic)00(Manual)/01(Automatic)0.0 to 20.00.0 to 20.00.0 to 50.00.0 to 50.000(VC)/01(Reduced torque)/06 (Reduced torque 1)00(VC)/01(Reduced torque)/06 (Reduced torque 1)20 to 10020 to 10000(Disable)/01(Enable)/02(Frequency detection)0.0 to 60.00.0 to 5.00. to 100.0.0 to 60.000(Edge)/01(Level)

0.0/start freq. to maximum freq.

V/f Characteristic

DC braking

Run modeeditFunction Code Name Range

Default

-EF(CE) -U(UL) -R(JP)Unit

Lo Hi

0.0 to 400.00.0 to 999.9F(Forward)/o(Stop)/r(Reverse)0.00 to 99.99/100.0 to 999.9/1000. to 9999.

0.00 to 99.99/100.0 to 999.9/1000. to 9999./1000 to 9999(10000 to 99999)0.0 to 600.00. to 9999./1000 to 9999/ 100 to 999 (10000 to 99900)0. to 9999./1000 to 99990.0 to 200.00. to 9999.

Displays trip event information

0.0 to 999.90.0 to 100.0

X

Function List

8

A Group: Standard functions

b Group: Fine-tuning functions



PID Control

PID Control

AVR function

Operation mode andacc./dec. function

External freq. tuning

Frequencycaluculation

A061A261A062A262A063A064A065A066A067A068A071A072A073A074A075A076A077A078A081

A082

A085A086A092A292A093A293A094A294A095A295A096A296A097A098A101A102A103A104A105A141A142A143A145A146A151A152A153A154A155

Frequency upper limit settingFrequency upper limit setting, 2nd motorFrequency lower limit settingFrequency lower limit setting, 2nd motorJump (center) frequency setting 1Jump (hysteresis) frequency setting 1Jump (center) frequency setting 2Jump (hysteresis) frequency setting 2Jump (center) frequency setting 3Jump (hysteresis) frequency setting 3PID EnablePID EnablePID proportional gainPID integral time constantPID derivative time constantPV scale conversionPV source settingReverse PID actionPID output limitAVR function select

AVR voltage select

Operation mode selectionEnergy saving mode tuningAcceleration (2) time settingAcceleration (2) time setting, 2nd motorDeceleration (2) time settingDeceleration (2) time setting, 2nd motorSelect method to switch to Acc2/Dec2 profileSelect method to switch to Acc2/Dec2 profile, 2nd motorAcc1 to Acc2 frequency transition pointAcc1 to Acc2 frequency transition point, 2nd motorDec1 to Dec2 frequency transition pointDec1 to Dec2 frequency transition point, 2nd motorAcceleration curve selectionDeceleration curve selection[OI]-[L] input active range start frequency[OI]-[L] input active range end frequency[OI]-[L] input active range start current[OI]-[L] input active range end current[OI]-[L] input start frequency enableA input select for calculate functionB input select for calculate functionCalculation symbolADD frequencyADD direction selectPot. input active range start frequencyPot. input active range end frequencyPot. input active range start currentPot. input active range end currentPot.input start frequency enable

0.0/Freq. lower limit setting to maximum freq.0.0/Freq. lower limit setting (2nd) to maximum freq. (2nd)0.0/Start freq. to freq. upper limit setting0.0/Start freq. (2nd) to freq. upper limit setting (2nd)0.0 to 400.0.0 to 10.00.0 to 400.0.0 to 10.00.0 to 400.0.0 to 10.000(Disable)/01(Enable)0.2 to 5.00.0 to 150.00.00 to 100.00.01 to 99.9900([OI] terminal)/01([O] terminal)/02(RS485)/10(Calculation result)00(OFF)/01(ON)0.0 to 100.000(Enable)/01(Disable)/02(Enabled except during deceleration)200V class: 200/215/220/230/240400V class: 380/400/415/440/460/48000(Normal)/01(Energy-saver)0.0 to 100.00.01 to 99.99/100.0 to 999.9/1000. to 3000.0.01 to 99.99/100.0 to 999.9/1000. to 3000.0.01 to 99.99/100.0 to 999.9/1000. to 3000.0.01 to 99.99/100.0 to 999.9/1000. to 3000.00(2CH from input terminal)/01(transition freq.)00(2CH from input terminal)/01(transition freq.)0.0 to 400.00.0 to 400.00.0 to 400.00.0 to 400.000(Linear)/01(S-curve)00(Linear)/01(S-curve)0.0 to 400.00.0 to 400.00. to 100.0. to 100.00(Use setting value)/01(0Hz)00(Digital operator)/01(Keypad potentiometer)02(O input)/03(OI input)/04(RS485)00(A141+A142)/01(A141-A142)/02(A141*A142)0.0 to 400.000(Plus)/01(Minus)0.0 to 400.00.0 to 400.00.0 to 100.00.0 to 100.000(Use offect (A151 value))/01(Use 0Hz)

0.00.00.00.00.00.50.00.50.00.5001.01.0

0.001.0000000.000

200/400

0050.0

15.0015.0015.0015.00

00000.00.00.00.000000.00.00.

100.010102000.0000.00.00.0

100.01

0.00.00.00.00.00.50.00.50.00.5001.01.0

0.001.0000000.000

200/400

0050.0

15.0015.0015.0015.00

00000.00.00.00.000000.00.00.

100.010102000.0000.00.00.0

100.01

0.00.00.00.00.00.50.00.50.00.5001.01.0

0.001.0000000.002

200/400

0050.0

15.0015.0015.0015.00

00000.00.00.00.000000.00.00.

100.010102000.0000.00.00.0

100.01

HzHzHzHzHzHzHzHzHzHz--

secsec---%-

V

-%

secsecsecsec--HzHzHzHz--HzHz%%----Hz-HzHz%%-

XXXXXXXXXXX

XXXXX

X

XX

XXXXXXXXXXXXXXXX

XXXXXX


Default


Lo Hi

X

X

XXXXXXXX

Restart afterinstantaneous power

failure

b001

b002b003

b004

b005

b011

b012

b212

b013b213

Selection of automatic restart mode

Allowable under-voltage power failure timeRetry wait time before motor restartInstantaneous power failure / under-voltage tripalarm enableNumber of restarts on power failure / under-voltagetrip eventsStart frequency to be used in case of frequencypull-in restart

Electronic thermal setting

Electronic thermal setting, 2nd motor

Electronic thermal characteristicElectronic thermal characteristic, 2nd motor

00(Alarm output)/01(Restart at 0Hz)/02(Resume after freq. matching)/03(Resume freq. matching then trip)0.3 to 25.00.3 to 100.0

00(Disable)/01(Enable)

00(Restart 16 times)/01(Always restart)

00(frequency at previous shutoff)/01(Max. Hz)/02(Set frequency)

0.2*Rated current to 1.0*Rated current

00(Reduced torque)/01(Constant torque)/02(Reduced torque 2)

00

1.01.0

00

00

00

0101

00

1.01.0

00

00

00

0101

-

secsec

-

-

-

A

A

--

X

XX

X

X

X

X

X

XX

Overload restriction

b021b221b022b222b023b223b028b228b029

b030

Overload restriction operation modeOverload restriction operation mode, 2nd motorOverload restriction settingOverload restriction setting, 2nd motorDeceleration rate at overload restrictionDeceleration rate at overload restriction, 2nd motorOverload restriction source selectionOverload restriction source selection, 2nd motorDeceleration rate of frequency pull-in restart

Current level of frequency pull-in restart

00(Disable)/01(Enable)/02(Enable for during acceleration)


0.1 to 3000.0

00(b022/b222 setting level)/01([O]-[L] analog input)

0.1 to 3000.0


0101

1.01.000000.5

0101

30.030.000000.5

--AA

secsec--

sec

A

XXXXXXXXX

X


Default


Lo Hi

Lock b031 Software lock mode selection

00([SFT] input blocks all edits)/01([SFT] input blocks edits exceptF001 and Multispeed parameters/02(No access to edits)/03(Noaccess to edits except F001 and Multi-speed parameters)/10(High-level access,including b031)

01 01

00

1.01.0

00

00

00

00000101

1.01.000000.5

01 - X

XX

Automatic EnergySaving

X

X

X

Rated current

Rated current

1.5*Rated current

Rated current

Function List

9

C Group: Intelligent terminal functions: Allowed[ X: Not allowed ]

Note: C014: 01 for UL version.


Default


Lo

Intelligent inputterminal

C001C201C002C202C003C203C004C204C005C205

Terminal [1] functionTerminal [1] function, 2nd motorTerminal [2] functionTerminal [2] function, 2nd motorTerminal [3] functionTerminal [3] function, 2nd motorTerminal [4] functionTerminal [4] function, 2nd motorTerminal [5] functionTerminal [5] function, 2nd motor

00(FW:Forward), 01(RV:Reverse), 02-05(CF1-CF4:Multispeed command),06(JG:Jogging), 07(DB:External DC braking), 08(SET:Second motor constantssetting), 09(2CH:Second accel./decel.), 11(FRS:Free-run stop), 12(EXT:External trip),13(USP:Unattended start protection), 15(SFT:Software lock), 16(AT:Analog inputselection), 18(RS:Reset), 19(PTC:Thermistor input), 20(STA:3-wire start), 21(STP:3-wire stop), 22(F/R:3-wire fwd./rev.), 23(PID:PID On/Off), 24(PIDC:PIDreset), 27(UP:Remote-controlled accel.), 28(DWN:Remote-controlled decel.),29(UDC:Remote-controlled data clearing), 31(OPE:Operator control), 50(ADD: Frequency setpoint), 51(F-TM: Force terminal enable), 52(RDY: Quick StartEnable), 53(S-ST: Special-Set (select) 2nd Motor Data), 64(EMR:Safety stop),255(NO:Not selected)

00000101020203031818

00000101161613131818

-

-

-

-

-

XXXXXXXXXX

XXXXXXXXXX

Hi

C011-C015

Terminal [1] to [5] active state 00(NO)/01(NC) 00 00* - X X

C021 Terminal [11] function

00(RUN:run signal), 01(FA1:Frequency arrival type 1 - constant speed),02(FA2:Frequency arrival type 2 - over-frequency), 03(OL:overloadadvance notice signal), 04(OD:Output deviation for PID control), 05(AL:alarm signal), 06(DC:Wire brake detect on analog input),07(FBV: Feedback voltage comparison), 08(NDc: NetworkDisconnection), 09(LOG: Logic operation result), 10(ODC: Option CardDetection Signal), 43(LOC:Low load detection)

01 01 - X X

Intelligent inputterminal

C026C028C031C036

C038

C039C041C241C042C043C044C052C053

Alarm relay function[AM] signal selectionTerminal [11] active stateAlarm relay active state

Output mode of low load detection signal

Low load detection levelOverload level settingOverload level setting, 2nd motorFrequency arrival setting for accelerationFrequency arrival setting for decelerationPID deviation level settingFeedback comparison upper levelFeedback comparison lower level

05000001

01

0.00.03.01000.0

05000001

01

0.00.03.01000.0

----

-

A

HzHz%%%

00(Output frequency)/01(Output current)00(NO)/01(NC)00(NO)/01(NC)00(Disabled)/01(During acceleration, deceleration and constantspeed)/02(During constant speed only)0.0 to 2.0*Rated current


0.0 to 400.00.0 to 400.00.0 to 100.00.0 to 100.00.0 to 100.0

XXXX

X

XXXXXXXX

X

XX

Serial communication

C070C071C072C074C075

C076

C077C078

SELECTION OF OPE/MODBUSCommunication speed selectionNode allocationCommunication parity selectionCommunication stop bit selection

Communication error mode

Communication error timeCommunication wait time

02(OPE or option)/03(485)04(4800bps)/05(9600bps)/06(19200bps)1. to 32.00(No parity)/01(Even parity)/02(Odd parity)1(1-bit)/2(2-bit)00(Trip)/01(Trip after deceleration stop)/02(Disable)/03(FRS)/04(Deceleration stop)0.00 to 99.990. to 1000.

02061.001

02

0.000.

02041.001

02

0.000.

----bit

-

secmsec

XXXXX

X

XX

Analog meter settingC081C082C086

0. to 200.0. to 200.0.0 to 10.0

[O] input span calibration[OI] input span calibration[AM] terminal offset tuning

100.100.0.0

100.100.0.0

%%V

00 (must not be changed)00(Clear last frequency)/01(Keep last frequency adjusted by UP/DWN)00(Cancel trip state at input signal ON transition)/ 01(Cancel trip stateat signal OFF transition)/02(Cancel trip state at input signal ON transition)00(RUN)/01(FA1)/02(FA2)/03(OL)/04(OD)05(AL)/06(Dc)/07(FBV)/08(NDc)/10(ODc)/43(LOC)00(AND)/01(OR)/02(XOR)0.0 to 100.00.0 to 100.00.0 to 100.00.0 to 100.0

Others

C091C101

C102

C141C142C143C144C145C148C149

Reserved (for factory adjustment)Up/Down memory mode selection

Reset mode selection

Input A select for logic output 1Input A select for logic output 2Logic function selectON delay time, output terminal 11OFF delay time, output terminal 11ON delay time, relayOFF delay time, relay

0000

00

0001000.00.00.00.0

0000

00

0001000.00.00.00.0

00000101020203031818

00

01

05000001

01

0.00.03.01000.002041.001

02

0.000.

100.100.0.00000

00

0001000.00.00.00.0

--

-

---

secsecsecsec

X

X

XXXXXXX

XXX


Default


Lo Hi

Others

b050b051b052b053b054b055b056b080b082b083

b084

b085b086b087b088

b089

b091

b092

b130b131b133b134b140b150b151

Selection of the non stop operationNon stop operarion start voltage settingOV-LAD Stop level of non stop operation settingDeceleration time of non stop operation settingFrequency width of quick deceleration settingDC bus AVR P-gainDC bus AVR I-time[AM] terminal analog meter adjustmentStart frequency adjustmentCarrier frequency setting

Initialization mode (parameters or trip history)

Country code for initializationFrequency scaling conversion factorSTOP key enableRestart mode after FRS

Monitor display select for networked inverter

Stop mode selection

Cooling fan control (see note below)

Over-voltage LADSTOP enableOver-voltage LADSTOP levelDC bus AVR selectionThreshold voltage of DC bus AVR settingOver-current trip suppressionCarrier modeQuick start enable

00(Disabled)/01(Enabled stop)/02(Enabled restart)0.0 to 1000.00.0 to 1000.00.01 to 30000.0 to 10.00.2 to 5.00.0 to 150.00. to 255.0.5 to 9.92.0 to 12.000(Trip history clear)/01(Parameter initialization)/02(Trip history clear and parameter initialization)00(JP)/01(CE)/02(US)0.1 to 99.900(Enable)/01(Disable)00(Restart from 0Hz)/01(Restart with frequency detection)01(Output frequency)/02(Output current)/03(Rotation direction)/04(PV, PID feedback)/05(Input terminal status)/06(Output terminal status)/07(Scaled output frequency)00(Deceleration and stop)/01(Free-run stop)00(Always ON)/01(ON during RUN, OFF during STOP)/02(Temperature controlled)00(Disable)/01(Enable)330 to 395V/660 to 790V00(Disabled)/01(Enabled)330 to 395V/660 to 790V00(Disable)/01(Enable)00(Disable)/01(Enable)00(Disable)/01(Enable)

000.00.01.00.00.20.2100.0.53.0

00

011.00000

01

00

00

00380/760

00380/760

010000

000.00.01.00.00.20.2100.0.53.0

00

021.00000

01

00

00

00380/760

00380/760

010000

000.00.01.00.00.20.2100.0.53.0

00

001.00000

01

00

00

00380/760

00380/760

010000

-VV

secHz-

sec-HzkHz

-

----

-

-

-

-V-V---

XXXXXXX

XX

X

X

XX

X

X

X

XXXX

XXXXXXX

X

X

X

X

X

Rated current

OC.Drive

OC.Decel

OC.Accel

Over.C

Over.L

Over.V

EEPROM

Under.V

CPU

EXTERNAL

USP

GND.Flt

OV.SRC

OH FIN

DRIV

TH

EMERGENCY

COMM

Protective Functions

10

Name

Over current

Overloadprotection *1

Over voltage protection

EEPROM error *2,3

Under-voltage error

CPU error

External trip

USP *4

Ground fault *5

Input over-voltage

Inverter thermal trip

Thermistor

Communications error

Cause(s) Display on digitaloperator

The inverter output was short-circuited, or the motor shaft is locked or has a heavyload. These conditions cause excessive current for the inverter, so the inverteroutput is turned OFF.

When a motor overload is detected by the electronic thermal function, the inverter trips and turns OFFits output.

When the DC bus voltage exceeds a threshold, due to regenerative energy from the motor.

When the built-in EEPROM memory has problems due to noise or excessive temperature, the invertertrips and turns OFF its output to the motor.A decrease of internal DC bus voltage below a threshold results in a control circuit fault. This conditioncan also generate excessive motor heat or cause low torque. The inverter trips and turns OFF its output.A malfunction in the built-in CPU has occurred, so the inverter trips and turns OFF its output to themotor.A signal on an intelligent input terminal configured as EXT has occurred. The inverter trips and turnsOFF the output to the motor.When the Unattended Start Protection (USP) is enabled, an error occurred when power is applied while aRun signal is present. The inverter trips and does not go into Run Mode until the error is cleared.The inverter is protected by the detection of ground faults between the inverter output and the motorduring powerup tests. This feature protects the inverter, and does not protect humans.When the input voltage is higher than the specified value, it is detected 100 seconds after powerupand the inverter trips and turns OFF its output.When the inverter internal temperature is above the threshold, the thermal sensor in the inverter moduledetects the excessive temperature of the power devices and trips, turning the inverter output OFF.

When a thermistor is connected to terminals [PTC] and [CM1] and the inverter has sensed thetemperature is too high, the inverter trips and turns OFF the output.

The inverter's watchdog timer for the communications network has timed out.

While atconstant speedDuringdecelerationDuringacceleration

Others

Display on remoteoperator/copy unit

Error Codes

Error codeOutput frequency

at trip pointMotor currentat trip point

Voltage betweenP(+) and N(-) at trip point

Cumulative inverterRUN time at trip point

Cumulative power-ontime at trip point

1 2 1 2 1 2 1 2 1 2

1 2

How to access the details about the present fault

Note 1: Reset operations acceptable 10 seconds after the trip. Note 2: If an EEPROM error (E08) occurs, be sure to confirm the parameter data values are still correct.Note 3: EEPROM error may occer at power-on after shutting down the power while copying data with remote operator or initializing data. Shut down the power after completing copy or initialization.Note 4: USP error occures at reseting trip after under-voltage error (E09) if USP is enabled. Reset once more to recover.Note 5: Ground fault error (E14) cannot be released with resetting. Shut the power and check wiring.

P Group: Expansion Card Functions

H Group: Motor constants functions

Note: The "P" Group parameters do not appear in the parameter list shown on the keypad display unless the expansion card is installed on the inverter.

Function List

Option Setting

Motor constants andgain

P044

P045

P046P047

P048

P049

H003H203H004H204H006H206

Network comm watchdog timer

Inverter action on network comm error

Polled I/O output instance numberPolled I/O input instance number

Inverter action on network idle mode

Network motor poles setting for RPM

0.00 to 99.9900(Trip (Error Code E70)) 01(Decelerate to stop and trip (Error Code E70))02(Hold last speed), 03(Free run stop), 04(Decelerate and stop)20/21/10070/71/10100(Trip (Error Code E70))01(Decelerate to stop and trip (Error Code E70))02(Hold last speed), 03(Free run stop), 04(Decelerate and stop)00 to 38

1.00

01

2171

01

0

1.00

01

2171

01

0

1.00

01

2171

01

0

sec.

-

--

-

-

Run modeedit

Run modeedit

Function Code

Function Code

Name

Name

Range

Range

Default

Default

-EF(CE)

-EF(CE)

-U(UL)

-U(UL)

-R(JP)

-R(JP)

Unit

Unit

Lo

Lo

Hi

Hi

X

X

XX

X

X

X

X

XX

X

X



Driver error An internal inverter error has occurred at the safety protection circuit between the CPU and main driverunit. Excessive electrical noise may be the cause. The inverter has turned OFF the IGBT module output.

Safety Stop Safety stop signal given.

Motor capacity, 1st motorMotor capacity, 2nd motorMotor poles setting, 1st motorMotor poles setting, 2nd motorMotor stabilization constant, 1st motorMotor stabilization constant, 2nd motor

0.2/0.4/0.55/0.75/1.1/1.5/2.2/3.0/4.0/5.5

2/4/6/8

0. to 255.

Factoryset44

100100

Factoryset44

100100

Factoryset44

100100

kWkW

polespoles

%%

XXXX

XXXX

Connecting Diagram

11

AL2

AL1

AL0

R(L1)

T/N(L3)

S(L2)

(T1) U

(T3) W

(T2) V

P24

4

5

3

2

1

PCS

L

AM

H

O

OI

L

DC24V

DC10V

11

CM2

(+1)PD

(+)P

(-)N

DC link choke

Motor

Intelligent relayoutput contacts

Intelligent outputterminal

Current input4mA~20mA

X200

Intelligent inputterminals

(5 terminals)Source type

DC 0~10V(8bit)

Terminal 1,2,3,4,5 H,O,OI 11

Common

Sink logic : L L CM2

Source logic : PCS

Note 1: Common terminals are depend on logic.

Note 2: Please choose proper inverter input volotage rating.

10k 250

Frequency setting1k ~2k

Dynamic breaking umit (BRD)

P

P

N

RBRB

R1 AL1

AL2R2

Power source1-/3-phase 200~240V+10%, -15%

3-phase 380~480V+10%, -15%50/60Hz 5%

Short bar

Source type logic

Connecting Diagram

12

!"#

"$"%

$#&#$ %#'(

")$*)$ "$' $+

$#&#$ ")$*)$

$#%,'

)%%#$ *)$

,-,

$#&#$ *)$

$#%,'+

$#%,'+

$(*#

!"%$ .'%

-/.$

#%,' 1111 11

",," "& 2

")% # "& 2

"$# 2 ",," $#%,'+ '%# 3#*#3 " "& 4

"$# 2 #'+# !""+# *%"*#% 5#%$#% *)$ 5""$'&# %'$&4

6%#7)# ( +#$$&

-

(', .%#'& ),$ 8

8

8

"9#% +")% #

*!'+# -:1 :

*!'+# /-/:1 :

;< :

Sink type logic

13

Wiring and Accessories

L1 L2 L3

U(T1) V(T2) W(T3)

+1

+

-

IM

Power Supply

Fuse

Inverter

Motor

Note 1: Field wiring connection must be made by a UL and c-UL listed closed-loop terminal connector sized for the wire gauge involved. Connector must be fixed using the crimping tool specified by the connector manufacturer. Note 2: Be sure to use large wire gauges for power wiring if the distance exceeds 20m (66ft). Note 3: Use 0.75mm2 /18 AWG wire for the relay terminals (AL0, AL1 and AL2) signal wire.

Name Function

This is useful in suppressing harmonics induced on the power supplylines, or when the main power voltage imbalance exceeds 3% (and power source capacity is more than 500kVA), or to smooth out line fluctuations. It also improves the power factor.

Electrical noise interference may occur on nearby equipment such as a radio receiver. This magnetic choke filter helps reduce radiat-ed noise (can also be used on output).

Reduces the conducted noise on the power supply wiring generated by theinverter. Connect to the inverter input side.

This capacitor filter reduces radiated noise from the main power wires in the inverter input side.

Suppresses harmonics generated by the inverter.

This is useful for increasing the inverter’s control torque for high duty-cycle (on-off) applications, and improving the decelerating capability.

Reduces radiated noise from wiring in the inverter output side.

Electrical noise interference may occur on nearby equipment such as a radio receiver. This magnetic choke filter helps reduce radiated noise (can also be used on input).

This reactor reduces the vibration in the motor caused by the inver-ter’s switching waveforms, by smoothing the waveforms to approximate commercial power quality. It is also useful when wiring from the inverter to the motor is more than 10m in length, to reduce harmonics.

Sine wave shaping filter for the output side.

Input side AC reactor

Radio noise filter

EMC filter

Radio noise filter (Capacitor filter)

DC link choke

Braking resistor

Braking unit

Output side noise filter

Radio noise filter

AC reactor

LCR filter

Input Voltage

Applicable Motor

(kW(HP))Model

Wireing

Power Lines

AWG mm2 Signal Lines

Fuse (Class J)

0.2(1/4)

0.4(1/2)

0.55(3/4)

0.75(1)

1.1(1.5)

1.5(2)

2.2(3)

3.7(5)

5.5(7.5)

7.5(10)

0.4(1/2)

0.75(1)

1.5(2)

2.2(3)

3(4)

3.7(5)

4.0(5)

5.5(7.5)

7.5(10)

X200-002NFU2/SFEF2

X200-002LFRF2

X200-004NFU2/SFEF2

X200-004LFRF2

X200-005SFEF2

X200-007NFU2/SFEF2/LFRF2

X200-011SFEF2

X200-015NFU2/SFEF2

X200-015LFRF2

X200-022NFU2/SFEF2

X200-022LFRF2

X200-037LFU2/LFRF2

X200-055LFU2/LFRF2

X200-075LFU2/LFRF2

X200-004HFU2/HFEF2/HFRF2




X200-030HFEF2

X200-037HFRF2

X200-040HFU2/HFEF2



14

16

14

16

14

14

10

10

14

10

14

12

10

8

16

16

16

14

14

14

14

12

12

2.0

1.25

2.0

1.25

2.0

2.0

5.5

5.5

2.0

5.5

2.0

3.5

5.3

8.4

1.25

1.25

1.25

2.0

2.0

2.0

2.0

3.3

3.3

18 to 28 AWG0.14 to

0.75mm2

shelded wire

18 to 28 AWG0.14 to

0.75mm2

shelded wire

10

10

10

10

10

15

15

20

20

30

30

30

40

50

3

6

10

10

15

15

15

20

25

400V

200V

14

Torque characteristics/Derating Curves

150

130

95

80

5545

35

100

1 6 20 60 120

Out

put t

orqu

e (%

)

Base frequency = 60Hz Base frequency = 50Hz

100

130

150

7555

4535

90

1 5 16.7 50 120

Output frequency (Hz)Output frequency (Hz)

Out

put t

orqu

e (%

)

0.2~4kW

0.2~4kW

5.5, 7.5kW

Continuous performance

5.5, 7.5kW

Short time performanceShort time performance

Continuous performance

0.2~4kW

5.5, 7.5kW

0.2~4kW

5.5, 7.5kW

Torque characteristics

100%

95%

90%

85%

80%

75%

70%4 6 10 122 8

100%

95%

90%

85%

80%

75%

70%4 6 10 122 8

037LFU2/LFRF2

4 6 10 122 8

002～004、022SFEF2/NFU2/LFRF2, 005SFEF2、055LFU2/LFRF2

60%

65%

70%

75%

80%

85%

90%

95%

100%

4 6 10 122 8

055HFEF/HFU/HFRF

60%

65%

70%

75%

80%

85%

90%

95%

100%

4 6 10 122 8

002～022SFEF2/NFU2/LFRF2, 055、075LFU2/LFRF2

75%

80%

85%

90%

95%

100%

037LFU2

075LFU2/ LFRF2

055HFEF2/HFU2/HFRF2

4 6 10 122 8

004～030,055,075HFEF2/HFU2 004～022,055,075HFRF2

75%

80%

85%

90%

95%

100%

040HFEF2/HFU2/037HFRF2

037LFU2/LFRF2

007SFEF2/NFU2/LFRF2, 011SFEF2

004～015、075HFEF2/HFU2/HFRF2

022HFEF2/HFU2/ HFRF2

040HFEF2/HFU2/ 037HFRF2

030HFEF2

002～022SFEF2/NFU2/LFRF2, 055,075LFU2/LFRF2

075HFEF2/ HFU2/HFRF2

030HFEF2

004～022 HFEF2/HFU2/HFRF2

040HFEF2/HFU2/ 037HFRF2

015SFEF2/ NFU2/LFRF2

Derating CurvesUse the following derating curves to help determine the optimal carrier frequency setting for your inverter and find the output current derating.Be sure to use the proper curve for your particular X200 inverter model number.

For Correct Operation

15

Application to Motors

The overspeed endurance of a general-purpose motor is 120% of the rated speed for 2 minutes (JIS C4,004). For operation at higherthan 60Hz, it is required to examine the allowable torque of the motor, useful life of bearings, noise, vibration, etc. In this case, besure to consult the motor manufacturer as the maximum allowable rpm differs depending on the motor capacity, etc.

The torque characteristics of driving a general-purpose motor with an inverter differ from those of driving it using commercial power(starting torque decreases in particular). Carefully check the load torque characteristic of a connected machine and the driving torquecharacteristic of the motor.

Application to general-purpose motors

Operating frequency

Torque characteristics

The torque characteristics of driving a general-purpose motor with an inverter differ from those of driving it using commercial power Motor loss and

temperature increase

When run by an inverter, a general-purpose motor generates noise slightly greater than with commercial power.NoiseWhen run by an inverter at variable speeds, the motor may generate vibration, especially because of (a) unbalance of the rotorincluding a connected machine, or (b) resonance caused by the natural vibration frequency of a mechanical system. Particularly, becareful of (b) when operating at variable speeds a machine previously fitted with a constant speed motor. Vibration can be minimizedby (1) avoiding resonance points using the frequency jump function of the inverter, (2) using a tire-shaped coupling, or (3) placing arubber shock absorber beneath the motor base.

Vibration

Under continued, low-speed operation, oil lubrication can deteriorate in a power transmission mechanism with an oil-type gear box(gear motor) or reducer. Check with the motor manufacturer for the permissible range of continuous speed. To operate at more than60Hz, confirm the machine , s ability to withstand the centrifugal force generated.

Power transmission mechanism

The allowable rotation range of continuous drive varies depending on the lubrication method or motor manufacturer.(Particularly in case of oil lubrication, pay attention to the low frequency range.)

Application to special motors

Gear motor

For use of a brake-equipped motor, be sure to connect the braking power supply from the primary side of the inverter.Brake-equipped motor

There are different kinds of pole-change motors (constant output characteristic type, constant torque characteristic type, etc.), withdifferent rated current values. In motor selection, check the maximum allowable current for each motor of a different pole count. Atthe time of pole changing, be sure to stop the motor. Also see: Application to the 400V-class motor.

Pole-change motor

The rated current of a submersible motor is significantly larger than that of the general-purpose motor. In inverter selection, be sureto check the rated current of the motor.Submersible motor

Inverter drive is not suitable for a safety-enhanced explosion-proof type motor. The inverter should be used in combination with apressure-proof explosion-proof type of motor.*Explosion-proof verification is not available for X200 Series.

Explosion-proof motor

In most cases, the synchronous (MS) motor and the high-speed (HFM) motor are designed and manufactured to meet thespecifications suitable for a connected machine. As to proper inverter selection, consult the manufacturer.

Synchronous (MS) motorHigh-speed (HFM) motor

A single-phase motor is not suitable for variable-speed operation by an inverter drive. Therefore, use a three-phase motor.Single-phase motor

Application to the 400V-class motor

A system applying a voltage-type PWM inverter with IGBT may have surge voltage at the motor terminals resulting from the cable constantsincluding the cable length and the cable laying method. Depending on the surge current magnification, the motor coil insulation may bedegraded. In particular, when a 400V-class motor is used, a longer cable is used, and critical loss can occur, take the followingcountermeasures:(1) install the LCR filter between the inverter and the motor,(2) install the AC reactor between the inverter and the motor, or(3) enhance the insulation of the motor coil.

Notes on UseDrive

Run or stop of the inverter must be done with the keys on the operator panel or through the control circuit terminal. Do not operate byinstalling a electromagnetic contactor (MC) in the main circuit.Run/Stop

When the protective function is operating or the power supply stops, the motor enters the free run stop state. When an emergencystop is required or when the motor should be kept stopped, use of a mechanical brake should be considered.Emergency motor stop

A max. 400Hz can be selected on the X200 Series. However, a two-pole motor can attain up to approx. 24,000 rpm, which isextremely dangerous. Therefore, carefully make selection and settings by checking the mechanical strength of the motor andconnected machines. Consult the motor manufacturer when it is necessary to drive a standard (general-purpose) motor above 60Hz.A full line of high-speed motors is available from Hitachi.

High-frequency run

Installation location and operating environment

Avoid installation in areas of high temperature, excessive humidity, or where moisture can easily collect, as well as areas that are dusty, subjectto corrosive gasses, mist of liquid for grinding, or salt. Install the inverter away from direct sunlight in a well-ventilated room that is free ofvibration. The inverter can be operated in the ambient temperature range from -10 to 50 C.(Carrier frequency and output current must bereduced in the range of 40 to 50˚C.)

Unbalance factor of voltage =

VRS-(VRS+VST+VTR)/3(VRS+VST+VTR)/3

Max. line voltage (min.) - Mean line voltageMean line voltage x100

= x100 = x100 =1.5(%)205-202

202

For Correct Operation

16

In the following examples involving a general-purpose inverter, a large peak current flows on the main power supply side, and is ableto destroy the converter module. Where such situations are foreseen or the connected equipment must be highly reliable, install anAC reactor between the power supply and the inverter. Also, where influence of indirect lightning strike is possible, install a lightningconductor.(A) The unbalance factor of the power supply is 3% or higher. (Note)(B) The power supply capacity is at least 10 times greater than the inverter capacity (the power supply capacity is 500 kVA or more).(C) Abrupt power supply changes are expected.

Examples:(1) Several inverters are interconnected with a short bus.(2) A thyristor converter and an inverter are interconnected with a short bus.(3) An installed phase advance capacitor opens and closes.

In cases (A), (B) and (C), it is recommended to install an AC reactor on the main power supply side.Note: Example calculation with VRS = 205V, VST = 201V, VTR = 200V

VRS : R-S line voltage, VST : S-T line voltage, VTR : T-R line voltage

An inverter run by a private power generator may overheat the generator or suffer from a deformed output voltage waveform of thegenerator. Generally, the generator capacity should be five times that of the inverter (kVA) in a PWM control system, or six timesgreater in a PAM control system.

Main power supply

Installation of anAC reactor on the

input side

Using a private powergenerator

(1) Be sure to connect main power wires with R(L1), S(L2), and T(L3) terminals (input) and motor wires to U(T1), V(T2), and W(T3)terminals (output). (Incorrect connection will cause an immediate failure.)

(2) Be sure to provide a grounding connection with the ground terminal ( ).

When an electromagnetic contactor is installed between the inverter and the motor, do not perform on-off switching during runningoperation.

When used with standard applicable output motors (standard three-phase squirrel-cage four-pole motors), the X200 Series does notneed a thermal relay for motor protection due to the internal electronic protective circuit. A thermal relay, however, should be used:• during continuous running outside a range of 30 to 60 Hz.• for motors exceeding the range of electronic thermal adjustment (rated current). • when several motors are driven by the same inverter; install a thermal relay for each motor. • The RC value of the thermal relay should be more than 1.1 times the rated current of the motor. Where the wiring length is 10 m or

more, the thermal relay tends to turn off readily. In this case, provide an AC reactor on the output side or use a current sensor.

Install a circuit breaker on the main power input side to protect inverter wiring and ensure personal safety. Choose an inverter-compatible circuit breaker. The conventional type may malfunction due to harmonics from the inverter. For more information, consultthe circuit breaker manufacturer.

Notes on Peripheral Equipment Selection

Wiring connections

Wiring between

inverter andmotor

Installing a circuit breaker

The wiring distance between the inverter and the remote operator panel should be 20 meters or less. When this distanceisexceeded, use CVD-E (current-voltage converter) or RCD-E (remote control device). Shielded cable should be used on thewiring.Beware of voltage drops on main circuit wires. (A large voltage drop reduces torque.)

IWiring distance

If the earth leakage relay (or earth leakage breaker) is used, it should have a sensitivity level of 15 mA or more (per inverter).Earth leakage relayDo not use a capacitor for power factor improvement between the inverter and the motor because the high-frequency components ofthe inverter output may overheat or damage the capacitor.Phase advance capacitor

Electromagneticcontactor

Thermal relay

High-frequency Noise and Leakage Current(1) High-frequency components are included in the input/output of the inverter main circuit, and they may cause interference in a transmitter,

radio, or sensor if used near the inverter. The interference can be minimized by attaching noise filters (option) in the inverter circuitry.(2) The switching action of an inverter causes an increase in leakage current. Be sure to ground the inverter and the motor.

Lifetime of Primary PartsBecause a DC bus capacitor deteriorates as it undergoes internal chemical reaction, it should normally bereplaced every five years. Be aware, however, that its life expectancy is considerably shorter when theinverter is subjected to such adverse factors as high temperatures or heavy loads exceeding the rated currentof the inverter.The approximate lifetime of the capacitor is as shown in the figure at the right when it is used12 hours daily (according to the " Instructions for Periodic Inspection of General-Purpose Inverter "(JEMA).)Also, such moving parts as a cooling fan should be replaced. Maintenance inspection and partsreplacement must beperformed by only specified trained personnel.

50

40

30

2.5 5 10Capacltor lifetime(years)A

mbi

ent t

empe

ratu

re(˚

C)

Precaution for Correct Usage• Before use, be sure to read through the Instruction Manual to insure proper use of the inverter.• Note that the inverter requires electrical wiring; a trained specialist should carry out the wiring.• The inverter in this catalog is designed for general industrial applications. For special applications in fields such as aircraft, outer space,

nuclear power, electrical power, transport vehicles, clinics, and underwater equipment, please consult with us in advance.• For application in a facility where human life is involved or serious losses may occur, make sure to provide safety devices to avoid a serious

accident.• The inverter is intended for use with a three-phase AC motor. For use with a load other than this, please consult with us.

Information in this brochure is subject to change without notice.

MEMO

17

MEMO

18

x200 series variable frequency drive | industrial eco ...analog frequency monitor, analog current...

Documents