x-ie data sheet - hilti

April 2021

X-IEDATA SHEETInsulation fastener

04/2021 2www.hilti.group

X-IE

X-IE 6 and X-IE 9 insulation fasteners

Product data

X-IE 6 Product description• Suitable for a wide range of insulation materials –

Soft mineral wool, mineral wool, EPS, XPS, PIR, PUR, soft core multilayer board, rigid core multilayer board

• Suitable for 20–200 mm thick insulation• Very high thermal efficiency in a one-step solution• No holes in the fastener shank – helping prevent mold and

moisture penetration in the insulation material• Gauge included for easy visual control of correct fastener

driving depth• Specially-designed 90 mm disc diameter for soft mineral

wool, providing excellent clamping of the insulationX-IE 9

Dimensions

Ø

Ls

Designation Diameter Ø Nail length L sX-IE 6 60 mm 47–62 mmX-IE 9 90 mm 47–62 mm

Material properties for plastic parts

Element Designation Material Color Other propertiesPlate X-IE 6 HDPE Colorless UV stabilized materialPlate X-IE 9 HDPE Black UV stabilized material

3 04/2021www.hilti.group

X-IE

Material properties for carbon steel parts

Element Designation Material Coating Minimum coating thickness

Hardness

NailX-PX 47, X-PX 52, X-PX 62

Carbon steel Zinc 5 µm 58 HRC

Approvals and certificates

Authority Approval / certificate no. Date of issue Country of issueSocotec 1601601R0000003 07/ 2019 FranceITB AT-15-7235 / 2015 06/ 2016 PolandITB AT-15-7696 / 2016 12/ 2016 PolandRussian Ministry / FCS TS / TO 5851-19 10/ 2019 Russia

Not all information presented in this product data sheet might be subject to approval / certificate content. Please refer to approval / certificate for further information.

Applications

Curtain wall insulation Ceiling insulation Basement perimeterinsulation

Base materials

Soft concrete

Medium concrete

Tough concrete

Solid sand- lime masonry

Solid brick Steel


X-IE

• Soft core multilayer board: hard top layer with insulation core of mineral wool • Rigid core multilayer board: hard top layer with insulation core of EPS, XPS, PIR,

PUR

• The intended use comprises fastening in dry conditions.

• During construction, exposure to UV due to solar radiation of the fixing element not protected by rendering shall not exceed the time of 6 weeks.

• The temperature during installation of the fixing element shall not be less than 5 °C.

Fastened materials

Load condition

Environmental conditions

Soft mineral wool

Staticquasi-static

Mineral wool

EPS XPS PIR, PUR

Soft and rigid core multilayer board

Application requirements

Fastened material properties

tI

Fastened material

Compressive strength

Fastened material thickness tl

Soft mineral wool < 500 kN / m2 50–200 mmMineral wool < 500 kN / m2 20–200 mmEPS, XPS, PIR, PUR, soft core multilayer board

< 500 kN / m2 20–200 mm

Rigid core multilayer board < 500 kN / m2 14–197 mm


X-IE

Base material properties

tII

Base material Base material strength

Base material thickness tII

Soft, medium concrete fcc = 15–45 N / mm2 ≥ 80 mm

Tough concrete fcc = 45–65 N / mm2 ≥ 80 mmSolid sand-lime masonry fb = 15–45 N / mm2 –

Solid brick fb = 28–45 N / mm2 –Steel fu = 360–450 N / mm2 4–6 mm

Fastener edge distance and spacing in base material

cs

sc

ce

c e

Minimum corner distance ce

Minimum edge distance c

Minimum fastener spacing distance s

100 mm 75 mm 100 mm

Number of fasteners per m²

Fastened material Fastened material weight Minimum number of fasteners per m²

Soft mineral wool, mineral wool, EPS, XPS, PIR, PUR,soft core multilayer board, rigid core multilayer board

≤ 15 kg/m² 4> 15 kg/m² 5

Fastened material Fastened material density Minimum number of fasteners per m²

Soft mineral wool, mineral wool, EPS, XPS, PIR, PUR,soft core multilayer board, rigid core multilayer board

≤ 75 kg/m3 4> 75 kg/m3 5

Please consult insulation material supplier

Fastener edge distance and spacing in insulation material


X-IE

Performance data

Recommended resistance under tension and shear load

N

V

Base material TensionNrec

ShearVrec

Soft, medium concrete 0.4 kN 0.4 kNTough concrete 0.2 kN 0.2 kNSolid sand-lime masonry 0.2 kN 0.2 kNSolid brick 0.2 kN 0.2 kNSteel 0.6 kN 0.6 kN

• For more details in relation to base material properties, please refer to the chapter

Fastener selection guide in the Direct Fastening Technology Manual (DFTM). • The above data value for solid sand-lime masonry and solid brick are based

on laboratory and field experience. Because of the wide variety of types and forms of masonry in use worldwide, users are advised to carry out tests on site or on masonry of the type and form on which the fastenings are to be made.

• The above data refers to the fastener pull-out failure mode. • For pull-over under tension load please consult insulation material supplier.

Stick rate estimation

Designation Soft, medium concrete15 ≤ fc,cube ≤ 45 N / mm2

Tough concrete45 < fc,cube ≤ 65 N / mm2

X-IE 6, X-IE 9 90 %–95 % 85 %–90 %

The stick rate indicates the percentage of nails that were driven correctly to carry a load. Stick rate can vary from the above values depending on job site conditions

Thermal efficiency according to EOTA TR 025

Application Insulation thicknesstI

Point thermal transmittanceϰ

Curtain wall insulation 60–90 mm 0.002 W/K100–200 mm 0.001 W/K

Ceiling insulation 60–90 mm 0.002 W/K100–200 mm 0.001 W/K

Basement perimeter insulation

60 mm 0.003 W/K70–100 mm 0.002 W/K120–200 mm 0.001 W/K


X-IE

■ = recommended, ■ = feasible

Cartridge recommendation

Base material Cartridge color (tool power level)Tool type: DX 6 IE

Tool type: DX 5 IE, DX 460 IE

Cartridge type: 6.8/11 M Cartridge type: 6.8/11 MSoft, medium concrete titanium ■ (2–8) yellow ■, red ■Tough concrete titanium ■ (2–8) yellow ■, red ■Solid sand-lime masonry titanium ■ (1–5) green ■, yellow ■Solid brick titanium ■ (1–5) green ■, yellow ■Steel titanium ■ (2–8) yellow ■, red ■

Designation Tools and equipmentDX 6 IE DX 5 IE DX 460 IEL equipmentFastener guide:X-6-FIE-LPiston:X-6-5-PIE-L

XL equipmentFastener guide:X-6-FIE-XLPiston:X-6-5-PIE-XL

L equipmentFastener guide:X-5-460-FIE-LPiston:X-5-460-PIE-L

XL equipmentFastener guide:X-5-460-FIE-XLPiston:X-5-460-PIE-XL

L equipmentFastener guide:X-5-460-FIE-LPiston:X-5-460-PIE-XL

XL equipmentFastener guide:X-5-460-FIE-XLPiston:X-5-460-PIE-XL

X-IE 6X-IE 6-20 X-IE 6-140 ■ ■ ■ ■ ■ ■X-IE 6-150 X-IE 6-200 ■ ■ ■

X-IE 9X-IE 9-50 X-IE 9-140 ■ ■ ■ ■ ■ ■X-IE 9-160 X-IE 9-200 ■ ■ ■

System recommendation

Tool and energy recommendation

• For more details, please refer to the chapter Accessories and consumables compatibility in the Direct Fastening Technology Manual (DFTM).

• Tool power level adjustment by setting tests on site. • Start tool energy selection with lowest recommended tool power level. • Correct according requirement from chapter quality assurance.


X-IE

Fastened material Insulation thickness tI

Designation Nail Item number

Mineral wool, EPS, XPS, PIR, PUR, soft core multilayer board

20 mm X-IE 6-20 X-PX 47 214395625 mm X-IE 6-25 X-PX 47 204171430 mm X-IE 6-30 X-PX 52 204171535 mm X-IE 6-35 X-PX 52 204171640 mm X-IE 6-40 X-PX 52 204171750 mm X-IE 6-50 X-PX 62 204171860 mm X-IE 6-60 X-PX 62 204171970 mm X-IE 6-70 X-PX 62 204174075 mm X-IE 6-75 X-PX 62 204174180 mm X-IE 6-80 X-PX 62 204174290 mm X-IE 6-90 X-PX 62 2041743100 mm X-IE 6-100 X-PX 62 2041744120 mm X-IE 6-120 X-PX 62 2041745125 mm X-IE 6-125 X-PX 62 2323244140 mm X-IE 6-140 X-PX 62 2041393150 mm X-IE 6-150 X-PX 62 2048523160 mm X-IE 6-160 X-PX 62 2041394175 mm X-IE 6-175 X-PX 62 2323245180 mm X-IE 6-180 X-PX 62 2041395200 mm X-IE 6-200 X-PX 62 2041396

Fastener selection



Soft mineral wool

50 mm X-IE 9-50 X-PX 62 209203460 mm X-IE 9-60 X-PX 62 204174680 mm X-IE 9-80 X-PX 62 204174790 mm X-IE 9-90 X-PX 62 2041748100 mm X-IE 9-100 X-PX 62 2041749120 mm X-IE 9-120 X-PX 62 2041750140 mm X-IE 9-140 X-PX 62 2041751160 mm X-IE 9-160 X-PX 62 2041752180 mm X-IE 9-180 X-PX 62 2041753200 mm X-IE 9-200 X-PX 62 2041754


X-IE



Rigid core multilayer board

14–17 mm X-IE 6-20 X-PX 47 214395619–22 mm X-IE 6-25 X-PX 47 214171424–27 mm X-IE 6-30 X-PX 52 214171529–32 mm X-IE 6-35 X-PX 52 214171634–37 mm X-IE 6-40 X-PX 52 214171744–47 mm X-IE 6-50 X-PX 62 214171857–57 mm X-IE 6-60 X-PX 62 214171964–67 mm X-IE 6-70 X-PX 62 214174069–72 mm X-IE 6-75 X-PX 62 214174174–77 mm X-IE 6-80 X-PX 62 214174284–87 mm X-IE 6-90 X-PX 62 214174394–97 mm X-IE 6-100 X-PX 62 2141744114–117 mm X-IE 6-120 X-PX 62 2141745119–122 mm X-IE 6-125 X-PX 62 2323244134–137 mm X-IE 6-140 X-PX 62 2041393144–147 mm X-IE 6-150 X-PX 62 2048523154–157 mm X-IE 6-160 X-PX 62 2041394169–172 mm X-IE 6-175 X-PX 62 2323245174–177 mm X-IE 6-180 X-PX 62 2041395194–197 mm X-IE 6-200 X-PX 62 2041396

• Insulation board thickness tolerance: ±3 mm

• Soft mineral wool, mineral wool: for intermediate thicknesses use next shorter fastener, example: for mineral wool insulation thickness 110 mm, use X-IE 6-100

• EPS, XPS, PIR, PUR, soft core multilayer board: for intermediate thicknesses use next longer fastener, example: for PIR insulation thickness 110 mm, use X-IE 6-120

• Rigid core multilayer board: for thicknesses not specified, please contact Hilti


X-IE

Fastening inspection

tI

x hET Designation Embedment depth

hET

Distance between nail head and X-IE platex

X-IE 6-20 24 – 29 mm 4 – 9 mmX-IE 6-25 24 – 29 mm 4 – 9 mmX-IE 6-30 24 – 29 mm 4 – 9 mmX-IE 6-35 24 – 29 mm 4 – 9 mmX-IE 6-40 24 – 29 mm 9 – 14 mmX-IE 6-50, X-IE 9-50 24 – 29 mm 9 – 14 mmX-IE 6-60, X-IE 9-60 24 – 29 mm 19 – 24 mmX-IE 6-70 24 – 29 mm 29 – 34 mmX-IE 6-75 24 – 29 mm 34 – 39 mmX-IE 6-80, X-IE 9-80 24 – 29 mm 39 – 44 mmX-IE 6-90, X-IE 9-90 24 – 29 mm 49 – 54 mmX-IE 6-100, X-IE 9-100 24 – 29 mm 59 – 64 mmX-IE 6-120, X-IE 9-120 24 – 29 mm 79 – 84 mmX-IE 6-125 24 – 29 mm 84 – 89 mmX-IE 6-140, X-IE 9-140 24 – 29 mm 99 – 104 mmX-IE 6-150 24 – 29 mm 109 – 114 mmX-IE 6-160, X-IE 9-160 24 – 29 mm 119 – 124 mmX-IE 6-175 24 – 29 mm 134 – 139 mmX-IE 6-180, X-IE 9-180 24 – 29 mm 139 – 144 mmX-IE 6-200, X-IE 9-200 24 – 29 mm 159 – 164 mm

Quality assurance


X-IE

Setting depth control and power tool adjustment

Check setting depth with the gaugeimmediately after fastening

Adjust the power setting if required

• Visible setting failures must be replaced with a new fastener, not in the same hole

• These are abbreviated instructions which may vary by application. • ALWAYS review / follow the instructions accompanying the product

x-ie data sheet - hilti

Documents