wpled 26w installation instructions - rab …...wpled 26w installation instructions thank you for...
TRANSCRIPT
WPLED 26W INSTALLATION INSTRUCTIONSThank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
®
JUNCTION BOX MOUNT FOR CONDUITFor use on applications where conduit wiring is needed.1. Loosen (4) Lens Screws and swing open Hinged Door.
Screws will remain in place with O-Rings.2. Loosen and remove (2) Housing Screws. Remove Housing
from Back Box. Keep Housing Gasket intact for re-assembly.3. Feed wires into Back Box through Silicone Wiring Plug, if
not using conduit/ connectors.4. Secure Back Box to the mounting surface using hardware
appropriate for that mounting surface. Silicone around the edge of Back Box Gasket (self adhesive) and/ or junction box.
5. Wire the fixture using UL listed wire connectors according to NEC and local codes. Apply sealant to all unused conduit entry points.
6. Place Gasket between Back Box and Housing. Re-mount Housing to Back Box. Check Housing Gasket seal all around the Back Box.
7. Re-mount Door to Housing. Tighten (4) Lens Screws. Check door gasket (not shown) seal.
8. Fixture is UL Listed for down and up lighting and may be mounted in either position. Fixture may not melt heavy snow accumulation in an uplight position.
Lens Screws
Junction Box Surface Mount
Back Box Housing Gasket
Housing
Hinged Door
Housing Screws
SURFACE MOUNT FOR RECESSED JUNCTION BOXFor use with recessed junction box and wiring.1. Mount Surface Plate to fixture with (4) Surface Plate
Screws. There are two screws from the front and two screws from the back. Make sure Housing Gasket makes complete seal all the way around.
2. Use supplied crossbar. Mount Crossbar to recessed junction box with (2) screws.
3. Place Junction Box Gasket on back of the fixture. Gasket should create seal against mounting surface.
4. Wire fixture to supply wires in recessed junction box according to wiring section.
5. Use 1/4 x 20 stainless steel Mounting Screw to attach fixture to Crossbar. Tighten Mounting Screw.
6. Cover screw with Cap, provided.7. Fixture is UL Listed for down and up lighting and may be
mounted in either position. Fixture may not melt heavy snow accumulation in an uplight position.
Crossbar
Junction Box Gasket
Mounting Screw
Cap
Recessed Junction Box (not provided)
Surface Plate
Housing Gasket
(4) Surface Plate Screws
IMPORTANTREAD CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
CAUTION: For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened firmly. Apply weatherproof silicone sealant around the edge of the Back Box and/or JunctionBox. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.
Door
Back Box Gasket
Silicone Wiring Plug
WPLED 26W INSTALLATION INSTRUCTIONSThank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
®
TROUBLESHOOTING 1. Check that the line voltage at fixture is correct. Refer to
wiring directions.2. Is the fixture is grounded properly?3. Be sure the photocell, if used, is functioning properly.
CLEANING & MAINTENANCECAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.1. Clean glass lens with non-abrasive glass cleaning
solution.2. Do not open fixture to clean the LED. Do not touch the
LED.
ON-OFF WIRINGUniversal voltage driver permits operation at 100V to 277VAC, 50 or 60Hz except fixtures factory ordered with a 120V photocell (/PC) and 277V photocell (/PC2). For Non-Dimming, follow the wiring directions as in fig. 1.1. For Junction Box Mount, feed wires through silicone
wiring plug into the junction box.2. Connect the black fixture lead to the (+) LINE supply lead.3. Connect the white fixture lead to the (-) COMMON supply
lead.4. Connect the bare copper Ground wire from fixture to
supply ground.
JUNCTION BOX 1. The Junction box has (4) conduit entry points on the
center of each side and (1) in the center back.2. Mounting Points are dimensioned below.
PATENTS: US: pat. D634,878, CN: ZL201030679778.2
4 3/4”
2 3/16”
3 1/2”
1 1/8”
1 1/8”
Mounting Points
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
Fig. 2
0-10V DIMMABLE WIRINGUniversal voltage driver permits operation at 120V thru 277V, 50 or 60 Hz. For 0-10V Dimming, follow the wiring directions as in fig. 2.1. For Junction Box Mount, feed wires through silicone
wiring plug into the junction box.2. Connect the black fixture lead to the (+) LINE supply lead.3. Connect the white fixture lead to the (-) COMMON supply
lead.4. Connect the GROUND wire from fixture to supply ground.
Do NOT connect the GROUND of the dimming fixture to the output.
5. Connect the purple fixture lead to the (V+) DIM lead.6. Connect the gray fixture lead to the (V-) DIM lead.7. Cap the yellow fixture lead, if present. Do NOT connect.
LIGHTFIXTURE
(+)LINE BLACK
(-)COMMON WHITE
GROUND GROUND
Fig. 1
WPLED26-IN 1213
Easy Installation & Product HelpTech Help LineCall our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.Northvale, New Jersey 07647 USA
rabweb.comVisit our website for product info
emailAnswered promptly [email protected]
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
WPLED 18W-26W WITH EMERGENCY BATTERYINSTALLATION INSTRUCTIONS
®
IMPORTANTREAD CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
CAUTION: For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened firmly. Apply weatherproof silicone sealant around the edge of the Back Box and/or JunctionBox. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.
Door
MOUNTINGCAUTION: Suitable for Wet Locations as Downlight and Wall Mount only.
1. Loosen and remove (4) Screws and separate Back Box from Emergency Housing. Use provided tether.
2. Drill necessary holes on Back Box. Measurements of drill positions are shown below.
3. Match the hole pattern and place the Gasket on the Back Box.
4. Secure the Back Box on the surface with hardware appropriate for the mounting surface.
5. Wire the fixture to the incoming supply wires according to NEC and local codes. Use UL listed wire connectors.
6. For WPLED*/E and WPLED*/EC wiring details refer to the appropriate Wiring Diagram section supplied Instruction Sheet.
7. Connect the battery connectors. DO NOT connect the Batteries before wiring the fixture to the supply.
8. Secure Housing to Back Box. Check Housing Gasket seal all around.
9. Apply sealant to all unused conduit entry points.To ensure weatherproof seal, apply weatherproof silicone sealant around the edge where the fixture meets the wall.
Housing
Screws
Two connectors for WPLED18/EC OR WPLED26/EC
Back Box Housing Gasket
Gasket
Screws
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
WPLED 18W-26W WITH EMERGENCY BATTERYINSTALLATION INSTRUCTIONS
®
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
WPLED18-26/E2-IN 0517
Easy Answersrabweb.comVisit our website for product info
Tech Help LineCall our experts - 888 722-1000
e-mailAnswered promptly - [email protected]
Free Lighting LayoutsAnswered online or by request© 2017 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
CLEANING & MAINTENANCE CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is ener-gized.
1. Clean glass lens & fixture with non-abrasive glass cleaning solution.
2. Do not open fixture to clean the LED. Do not touch the LED.
2.940[74,68]
7.500[190,5]
.600[15,24]
3.750[95,25]
DRILL TEMPLATE
7.5”3.75”
0.6”
2.94”
EMERGENCY BATTERY WIRING CAUTION: THIS IS AN EMERGENCY BATTERY BACKUP FIXTURE. Voltage could be present in Battery. To prevent high voltage from being present on output leads, inverter connector must be open. Do not join inverter connector until installation is complete and AC power is supplied to the emergency ballast. NOTE: Make sure that the necessary branch circuit wiring is available. An unswitched AC source of power is required. The emergency ballast must be fed from the same branch circuit as the AC ballast.Do not use any supply voltage other than those specified below. WPLED18 OR WPLED26 120V-277V, 50/60Hz1. Connect the UNSWITCHED black fixture lead to the HOT
supply lead.2. Connect switched and unswitched black leads together, if
not using a switching method.3. If switching, connect SWITCHED black lead to a switch.4. Connect the COMMON fixture lead to the COMMON
supply lead.5. For 0-10V Dimming, connect DIM (+) purple lead and DIM
(-) gray lead to 0-10V dimmer. 6. Connect the GROUND wire from fixture to supply ground.
Do NOT connect the GROUND of the dimming to the output.
7. All unused leads must be capped and insulated.8. After installation is complete, supply AC power to the
emergency ballast and join the inverter connector.9. At this point, power should be connected to both the
AC ballast and the emergency ballast, and the Charging Indicator Light should illuminate indicating the battery is charging.
10. A short-term discharge test may be conducted after the emergency ballast has been charging for one hour. Charge for 24 hours before conducting a long-term discharge test. Refer to OPERATION.
US: Pat. D643,147; CN: ZL201130171304.1; MX: 39260; TW: D159371; CA: D Patent Pending.
RE
D
BLA
CK EM
RG
ENC
Y D
RIV
ER
TEST
SW
ITC
H
IF U
NSW
ITC
HED
,C
AP
TWO
BLA
CK
WIR
ES T
OG
ETH
ER
EM
ERG
ENC
Y BA
TTER
Y
Cus
tom
er s
houl
d co
nnec
t uni
t con
nect
or o
nly
afte
rfin
ishi
ng w
iring
to A
C p
ower
. Bat
tery
cou
ld h
ave
char
ge a
nd s
hock
.
INV
ERTE
RC
ON
NEC
TOR
:C
ON
NEC
TO
NLY
AFT
ERA
C S
UP
PLY
PO
WER
IS
CO
NN
ECTE
DR
AB
LA
BEL
- A
DD
LED
DR
IVER
WP
LED
18/E
and
WP
LED
26/E
WIR
ING
DIA
GR
AM
(Ref
er to
nex
t pag
e fo
r WPL
ED*/E
C w
iring
dia
gram
)
WPL
ED26
/E2-
IN 0
517
AC
DRIV
ER
COM
GRO
UND
EMER
GEN
CY
D
RIVE
R
BATT
ERY
1
LEAV
E O
PEN
DO N
OT
CONN
ECT
DURI
NGM
ANUF
ACTU
RING
CUST
OM
ER S
HOUL
DCO
NNEC
T O
NLY
AFTE
RFI
NISH
ING
WIR
ING
TO
AC
POW
ER.
BATT
ERY
COUL
DHA
VE C
HARG
E &
SHO
CK
RED-
WHI
TE S
TRIP
E
RED
FUSE
HOLD
ER
CHAR
GIN
GIN
DICA
TOR
LIG
HT /
TEST
SW
ITCH
BLUE
WHI
TE
YELL
OW
YELL
OW
- BL
ACK
STRI
PE
WPL
ED26
UNSW
ITCH
ED H
OT
CHAR
GIN
GIN
DICA
TOR/
TEST
SWIT
CHBL
ACK
WHI
TE
WHI
TE/B
LACK
VIO
LET
BRO
WN
BLAC
KRED-
WHI
TE S
TRIP
E
BLUE
BLAC
K
BLAC
KG
REY
GRE
Y
WHI
TE
YELL
OW
/RED
WHI
TE -
RED
STRI
PE
WHI
TE
BLAC
K
WHI
TE
BLAC
K
BLAC
K
BLAC
K
BLAC
K
SWIT
CHED
HO
TRA
B LA
BEL
- ADD
RAB
LABE
L - A
DD
LABE
L PR
OVI
DED
BATT
ERY
2
EMER
GEN
CYHO
USIN
G
REDRE
D
RED
RED
BLUE
/ORA
NGE
RED
BLAC
K
WHI
TE
RED
YELL
OW
/RED
RED
WHI
TE
WHI
TE
WHI
TE
YELL
OW
/RED
RED
BLUE
BLUE
RED
WHI
TE
RED
YELL
OW
/RED
RED
WHI
TE
WHI
TE
BLUE
/ORA
NGE
BAT
1
BAT
1
BAT
2
BAT
2
BAT
1
BAT
1
BAT
2
BAT
2
WP
LED
18/E
C O
R W
PLE
D26
/EC
WIR
ING
DIA
GR
AM
(Ref
er to
pre
viou
s pa
ge fo
r WPL
ED*/E
wiri
ng d
iagr
am)
WPL
ED26
/E2-
IN 0
517
RED
BLAC
K EMER
GENC
Y DR
IVER
TEST
SW
ITCH
EMER
GENC
Y BA
TTER
Y
Custo
mer
shou
ld co
nnec
t unit
conn
ecto
r only
afte
rfin
ishing
wirin
g to
AC
powe
r. Ba
ttery
could
hav
ech
arge
and
shoc
k.
INVE
RTER
CON
NEC
TOR:
CON
NEC
TO
NLY
AFT
ERAC
SUP
PLY
POW
ER I
SCO
NN
ECTE
DRA
B LA
BEL
- AD
D
PC
D
RIVE
R
WP
LED
18/E
C O
R W
PLE
D26
/E W
ITH
PC
WIR
ING
DIA
GR
AM
(wiri
ng d
iagr
am)
WPLED 26W DC INSTALLATION INSTRUCTIONSThank you for buying RAB lighting � xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
®
JUNCTION BOX MOUNT FOR CONDUITFor use on applications where conduit wiring is needed.1. Loosen (4) Lens Screws and swing open Hinged Door.
Screws will remain in place with O-Rings.2. Loosen and remove (2) Housing Screws. Remove Housing
from Back Box. Keep Housing Gasket intact for re-assembly.3. Feed wires into Back Box through Silicone Wiring Plug, if
not using conduit/ connectors.4. Secure Back Box to the mounting surface using hardware
appropriate for that mounting surface. Silicone around the edge of Back Box Gasket (self adhesive) and/ or junction box.
5. Wire the � xture using UL listed wire connectors according to NEC and local codes. Apply sealant to all unused conduit entry points.
6. Place Gasket between Back Box and Housing. Re-mount Housing to Back Box. Check Housing Gasket seal all around the Back Box.
7. Re-mount Door to Housing. Tighten (4) Lens Screws. Check door gasket (not shown) seal.
8. Fixture is UL Listed for down and up lighting and may be mounted in either position. Fixture may not melt heavy snow accumulation in an uplight position.
Lens Screws
Junction Box Surface Mount
Back Box Housing Gasket
Housing
Hinged Door
Housing Screws
SURFACE MOUNT FOR RECESSED JUNCTION BOXFor use with recessed junction box and wiring.1. Mount Surface Plate to � xture with (4) Surface Plate
Screws. There are two screws from the front and two screws from the back. Make sure Housing Gasket makes complete seal all the way around.
2. Use supplied crossbar. Mount Crossbar to recessed junction box with (2) screws.
3. Place Junction Box Gasket on back of the � xture. Gasket should create seal against mounting surface.
4. Wire � xture to supply wires in recessed junction box according to wiring section.
5. Use 1/4 x 20 stainless steel Mounting Screw to attach � xture to Crossbar. Tighten Mounting Screw.
6. Cover screw with Cap, provided.7. Fixture is UL Listed for down and up lighting and may be
mounted in either position. Fixture may not melt heavy snow accumulation in an uplight position.
Crossbar
Junction Box Gasket
Mounting Screw
Cap
RecessedJunction Box(not provided)
Surface Plate
Housing Gasket
(4) Surface Plate Screws
IMPORTANTREAD CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF before installing or maintaining � xture. No user serviceable parts inside.
CAUTION: For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened � rmly. Apply weatherproof silicone sealant around the edge of the Back Box and/or JunctionBox. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.
Door
Back Box Gasket
Silicone Wiring Plug
WPLED 26W DC INSTALLATION INSTRUCTIONSThank you for buying RAB lighting � xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
®
TROUBLESHOOTING 1. Check that the line voltage at � xture is correct. Refer to
wiring directions.2. Is the � xture is grounded properly?3. Be sure the photocell, if used, is functioning properly.
CLEANING & MAINTENANCECAUTION: Be sure � xture temperature is cool enough to touch. Do not clean or maintain while � xture is energized.1. Clean glass lens with non-abrasive glass cleaning
solution.2. Do not open � xture to clean the LED. Do not touch the
LED.
ON-OFF WIRINGUniversal DC voltage driver permits operation at 10VDC to 30VDC.1. For Junction Box Mount, feed wires through silicone
wiring plug into the junction box.2. Connect the WHITE � xture lead to the
(+) supply lead.
3. Connect the BLACK � xture lead to the (-) supply lead.
4. Connect the bare copper Ground wire from � xture to sup-ply ground.
JUNCTION BOX 1. The Junction box has (4) conduit entry points on the
center of each side and (1) in the center back.2. Mounting Points are dimensioned below.
PATENTS: US: pat. D634,878, CN: ZL201030679778.2
4 3/4”
2 3/16”
3 1/2”
1 1/8”
1 1/8”
Mounting Points
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
Fig. 1
WPLED26DC-IN 0914
Easy Installation & Product HelpTech Help LineCall our experts 888 RAB-1000
©2014 RAB LIGHTING Inc.Northvale, New Jersey 07647 USA
rabweb.comVisit our website for product info
emailAnswered promptly [email protected]
(+) (+) WHITE
(-) (-) BLACK