wiring diagram iagram &&&& iiii...1:1000 ssscale eeeenterprise nnxxnx-nx ---01001101...

TenaControls LLC Milford, M@ 01757 U.S.@. www.Ten^Controls.com

TenaControls Brings Models to Life

© Copyright 2018 Ten^Controls LLC

P^ge 1

---- WWWWIRING IRING IRING IRING DDDDIAGRAMIAGRAMIAGRAMIAGRAM &&&& IIIINSTRUCTIONSNSTRUCTIONSNSTRUCTIONSNSTRUCTIONS ----

WWWWIRING IRING IRING IRING DDDDIAGRAM IAGRAM IAGRAM IAGRAM OFOFOFOF THE THE THE THE NXNXNXNX----01010101----1K1K1K1K KKKKITITITIT FFFFOR OR OR OR TTTTHE HE HE HE

1:10001:10001:10001:1000 SSSSCALE CALE CALE CALE EEEENTERPRISE NTERPRISE NTERPRISE NTERPRISE NXNXNXNX----01010101

IIIITEMS TEMS TEMS TEMS YYYYOU OU OU OU WWWWILL ILL ILL ILL NNNNEEDEEDEEDEED::::

Soldering Iron Solder Cutter

Wire Stripper

Refer to the Master Wiring Diagram on page 8 for all external connections to

the circuit board.

Here is the link to the Instructional Video:Here is the link to the Instructional Video:Here is the link to the Instructional Video:Here is the link to the Instructional Video:

https://www.youtube.com/watch?v=zHrNIi8qKQ4https://www.youtube.com/watch?v=zHrNIi8qKQ4https://www.youtube.com/watch?v=zHrNIi8qKQ4https://www.youtube.com/watch?v=zHrNIi8qKQ4

***A digital version of this Manual can be requested via email: ******A digital version of this Manual can be requested via email: ******A digital version of this Manual can be requested via email: ******A digital version of this Manual can be requested via email: *** [email protected]@[email protected]@tenacontrols.com




P^ge 2

HHHHow to distinguish which side is the Cathode and which side is ow to distinguish which side is the Cathode and which side is ow to distinguish which side is the Cathode and which side is ow to distinguish which side is the Cathode and which side is

the Anode on an LED:the Anode on an LED:the Anode on an LED:the Anode on an LED:

**Note:**Note:**Note:**Note: When using the shrink tubing, you need to only slide the shrink tubing over one

leg of the LED to keep it from shorting against the other leg. Then use a heat gun or

flame from a lighter to heat the shrink tubing until it shrinks around the wire connected

to one of the LED legs. Recommendation: shrink tube the positive side of the LED.

Now, connect the 9 volt battery clip, red to one side of the on/off switch, the other side

of switch to Red wire from board, then the Black from battery clip to Black wire from the

board. See Master Wiring Diagram on page 8.




P^ge 3

---- IIIINSTRUCTIONS NSTRUCTIONS NSTRUCTIONS NSTRUCTIONS ----

SSSSTROBTROBTROBTROBE E E E SSSSIDEIDEIDEIDE (REFERENCE THE MASTER WIRING DIAGRAM ON PAGE 8)

1. TwoTwoTwoTwo White White White White LED’s: LED’s: LED’s: LED’s: LED LED LED LED2222 ---- 3mm3mm3mm3mm and and and and LEDLEDLEDLED6666 ---- 3mm 3mm 3mm 3mm

The Two Anodes (+) of the Strobe LED’s, LED2 and LED6 will terminate to White wire from JST Micro Connector on the pc board. Then connect the Cathode (-) of LED2 and LED6 to Black wire from JST Micro Connector on the pc board.

NNNNAVIGATION AVIGATION AVIGATION AVIGATION SSSSIDEIDEIDEIDE (REFERENCE THE MASTER WIRING DIAGRAM ON PAGE 8)

2. TTTTwowowowo GreenGreenGreenGreen LED’s: LED’s: LED’s: LED’s: LED LED LED LED1111 ---- 1.8mm 1.8mm 1.8mm 1.8mm and LED5and LED5and LED5and LED5 ---- SMD SMD SMD SMD

The Anode (+) of the Navigation LED’s, LED1 will terminate to one side of resistor R3, the other side of resistor R3 will terminate to Orange wire from JST Micro Connector on the pc board. The Anode (+) of the Navigation led’s, LED5 will terminate to one side of resistor R4, the other side of resistor R4 will terminate to Orange wire from JST Micro Connector on the pc board. Then, connect the Cathode (-) of LED1 and LED5 to Black wire from JST Micro Connector on the pc board.

3. TTTTwowowowo Red Red Red Red LED’s: LED’s: LED’s: LED’s: LEDLEDLEDLED3333 ---- 1.8mm 1.8mm 1.8mm 1.8mm and and and and LEDLEDLEDLED4444 ---- SMD SMD SMD SMD The Two Anodes (+) of the Navigation LED’s, LED3 and LED4 will terminate to one side of resistor R5, the other side of resistor R5 will terminate to Orange wire from JST Micro Connector on the pc board. Then connect the Cathode (-) of LED1 and LED5 to Black wire from JST Micro Connector on the pc board.

4. Place the Strobe and Navigation LED’s in the locations shown on the LED Locations Drawings/Pictures on page 5, 6 & 7.




P^ge 4

LLLLEFT EFT EFT EFT AND AND AND AND RRRRIGHT IGHT IGHT IGHT SSSSIDE IDE IDE IDE IIIIMPULSE MPULSE MPULSE MPULSE EEEENGINESNGINESNGINESNGINES (REFERENCE THE MASTER WIRING DIAGRAM ON PAGE 8)

1. Two Blue LEDTwo Blue LEDTwo Blue LEDTwo Blue LED’s’s’s’s:::: LED LED LED LED7777 ---- 3mm 3mm 3mm 3mm and LEDand LEDand LEDand LED8888 ---- 3mm 3mm 3mm 3mm

The Two Anodes (+) of the Impulse Engines LED’s LED7 and LED8 will terminate to Blue wire from JST Micro Connector on the pc board. Then connect the Cathode (-) of LED7 and LED8 to Black wire from JST Micro Connector on the pc board.

NNNNAVIGATIONAL AVIGATIONAL AVIGATIONAL AVIGATIONAL DDDDEFLECTOR EFLECTOR EFLECTOR EFLECTOR DDDDISHISHISHISH (REFERENCE THE MASTER WIRING DIAGRAM ON PAGE 8)

2.2.2.2. Two Blue LED’s:Two Blue LED’s:Two Blue LED’s:Two Blue LED’s: LED1 LED1 LED1 LED12222 ---- 1.8mm 1.8mm 1.8mm 1.8mm and LED1 and LED1 and LED1 and LED13333 ---- 1.8mm 1.8mm 1.8mm 1.8mm

The Two Anodes (+) of the Navigation Deflector Dish LED’s LED12 and LED13 will terminate to one side of resistor R2, the other side of resistor R2 will terminate to Green wire from JST Micro Connector on the pc board. Then connect the Cathode (-) of LED12 and LED13 to Black wire from JST Micro Connector on the pc board.

LLLLEFT EFT EFT EFT AND AND AND AND RRRRIGHT IGHT IGHT IGHT SSSSIDE IDE IDE IDE BBBBLUE LUE LUE LUE NNNNACELLE ACELLE ACELLE ACELLE LLLLEDEDEDED’’’’SSSS (REFERENCE THE MASTER WIRING DIAGRAM ON PAGE 8)

1.1.1.1. Two BlTwo BlTwo BlTwo Blue LEDue LEDue LEDue LED’s’s’s’s:::: LED14LED14LED14LED14 ---- SMD SMD SMD SMD, LED15 , LED15 , LED15 , LED15 ---- SMD, SMD, SMD, SMD, LED16LED16LED16LED16 ---- SMD SMD SMD SMD and LED1and LED1and LED1and LED17777 ---- SMD SMD SMD SMD

The Four Anodes (+) of the Left and Right Side Nacelle LED’s LED14, LED15, LED16 and LED17 will terminate to one side of resistor R1, the other side of resistor R1 will terminate to Green wire from JST Micro Connector on the pc board. Then connect the Cathode (-) of LED14, LED15, LED16 and LED17 to Black wire from JST Micro Connector on the pc board..




P^ge 5

LLLLOWER OWER OWER OWER SSSSAUCER AUCER AUCER AUCER DDDDOME OME OME OME LLLLIGHTIGHTIGHTIGHT (REFERENCE THE MASTER WIRING DIAGRAM ON PAGE 8)

1.1.1.1. One WhiteOne WhiteOne WhiteOne White LED: LED: LED: LED: LED11 LED11 LED11 LED11 ---- 3mm 3mm 3mm 3mm

The Anode (+) of the Lower Dome LED, LED11 will terminate to one side of resistor R6, the other side of resistor R6 will terminate to Green wire from JST Micro Connector on the pc board. Then connect the Cathode (-) of LED11 to Black wire from JST Micro Connector on the pc board.

Now, attach a nine volt battery to the nine volt battery clip. Throw the on/off switch to

the on position.

TTTTOP OP OP OP VVVVIEW OF IEW OF IEW OF IEW OF LEDLEDLEDLED LLLLOCATIONSOCATIONSOCATIONSOCATIONS




P^ge 6

BBBBOTTOM OTTOM OTTOM OTTOM VVVVIEW OF IEW OF IEW OF IEW OF LEDLEDLEDLED LLLLOCATIONSOCATIONSOCATIONSOCATIONS




P^ge 7

RRRREAR EAR EAR EAR VVVVIEW OF IEW OF IEW OF IEW OF LEDLEDLEDLED LLLLOCATOCATOCATOCATIONSIONSIONSIONS

R1=150 OHMS R2,R3,R4,R5 = 300 OHMS R6 = 820 OHMSR1=150 OHMS R2,R3,R4,R5 = 300 OHMS R6 = 820 OHMSR1=150 OHMS R2,R3,R4,R5 = 300 OHMS R6 = 820 OHMSR1=150 OHMS R2,R3,R4,R5 = 300 OHMS R6 = 820 OHMS




P^ge 8

MMMMASTER ASTER ASTER ASTER WWWWIRING IRING IRING IRING DDDDIAGRAMIAGRAMIAGRAMIAGRAM




P^ge 9

WarrantyWarrantyWarrantyWarranty TenaControls LLC warrants that the control boards sold meet TenaControls specifications and are adequately contained, packaged and labeled and conform to the promises and affirmations of fact made on the container and label. THE FOREGOING WARRANTIES ARE EXCLUSIVE, AND ARE IN LIEU OF ALL OTHER WARRANTIES (WHETHER WRITTEN, ORAL OR IMPLIED) INCLUDING WARRANTY OR MERCHANTABILITY IN OTHER RESPECTS THAN EXPRESSLY SET FORTH ABOVE AND WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

In the event that there is a breach of express warranty by the manufacturer made in connection with the purchase of this product, if any, the sole remedy of any buyer shall be to return the product along with original sales receipt, at buyer’s expensebuyer’s expensebuyer’s expensebuyer’s expense for repair (or replacement of the product if repair is impossible) to the manufacturer’s facility in the Commonwealth of Massachusetts, located at 22 Hancock Street, Milford, MA 01757. Some states do not allow the exclusion or limitation of any incidental or consequential damages, so the above limitation may not apply to you. Nothing herein contained shall be construed to be a waiver by the manufacturer of any of the obligations imposed upon said buyer under the laws of the Commonwealth of Massachusetts except as herein specifically stated. This warranty is enforceable only by the buyer of the product or a person in the buyer’s immediate family. This warranty is enforceable for a period of FIVE YEARS FIVE YEARS FIVE YEARS FIVE YEARS from the date of purchase. Some states do not allow limitations on how long an implied warranty lasts, so the above warranty may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Warranty Void if:Warranty Void if:Warranty Void if:Warranty Void if: A) Product is altered in any way. B) Used for other than its intended use. C) Buyer mishandling.

wiring diagram iagram &&&& iiii...1:1000 ssscale eeeenterprise nnxxnx-nx ---01001101...

Documents