Wireless Router CW-5358U

Quick Installation Guide

(Including BT Downloader & DualWan Guide)

CHECK BEFORE YOU PROCESS:

Thank you very much for choosing cd-r king’s Wireless products. Please carefully go through

this Quick Installation Guide (QIG) before using this wireless router. Please note that this QIG

only provides you with basic connection guide. If you need more advance setup, please refer

to your user manual or link to www.cdrking.com.ph

You will need:

A standard CD-ROM drive

Internet connection should be setup & ready to use (ADSL or cable modem ready to connect).

Modem must provide RJ45 port to connect with CW-5358U.

Microsoft Windows compatible PC/Notebook with UPnP enabled network adapter

CAT 5 network cable(s), RJ45 port on PC/Notebook. Package Content: 1. IEEE 802.11 b/g/n CW-5358U wireless router x 1 2. 12V Power adapter x 1 3. QIG x 1 4. 2 dBi 2.4 GHz External detachable Antenna x 2 5. CD with User’s Manual and BT downloader x 1 6. Ethernet cable x 1 (8P8C)

Wireless Router LED light indication:

LED Description Light

IndicationFunction Note

On Power On Power Power

Off Power Off

Power light flash indicates

wireless router in process

On WLAN Port is connecting

Flash Data Transmitting WLAN WLAN Port Indication Light

Off WAN Port is not connecting

On LAN Port is connecting

Flash Data Transmitting LAN 2~4 LAN Port Indication Lights

Off LAN Port is not connecting

On LAN Port is connecting

Flash Data Transmitting LAN1/ Wan2 LAN Port Indication Lights

Off LAN Port is not connecting

INSTALLATION PROCESS: 1. Device Connection Diagram:

WAN Port: For connecting to your modem. LAN Port: For connecting to you computer. Highly recommend using LAN2~LAN4. In Dual WAN mode, LAN1 will become WAN2 port (Next to WAN port is WAN2) Adapter Port: For connecting to the power adapter. Reset Button: For bringing the device back to factory default setup. Please

use sharp and pointing item to press the Default button for about 10 seconds to restore back to factory setup. Then power off for 30 seconds and Power ON. Please Wait for 1 minute at least (may show limited connectivity please reboot and wait; it needs time to configure all settings!)

2. Wireless Router setup

1. Open your Internet browser, type in http://192.168.11.1 in Address, and press Enter.

2. When a new window pop-up, please type in User Name: admin, Password: admin; then click OK.

3. When first entered the CW-5358U’s web management page, you will see “Status” page

4. “Basic Setup” page. Please select your connection method from the options. If you are not sure your internet connection method, please contact your Internet service provider (ISP).

This section provides three common connection types from the "Basic Setup”. PPPoE user (ADSL)

DHCP user (Cable Modem)

Static user

PPPoE user (for DSL modem) in Setup

When selecting “PPPoE” as your internet connection method, please enter your PPPoE

Username and PPPoE Password provided by your Internet Service Provider (ISP). When

complete entering, please click “Save” at bottom of this page to save and complete your basic

setup.

PPPoE Username and Password is provided by your ISP, they are not the same

as the login name and password when entering to the wireless router’s web

management page. When entering the Username and Password, please make sure that

the characters are in the same format as your ISP provided.

Service name and other advanced functions are not necessarily setup needed.

You might refer to Help at the right column. If you are not clear with some functions,

please leave it at default value.

DHCP user (for Cable modem) in Setup

When selecting “DHCP user (Cable Modem)” as your internet connection method, please

enter the DNS server address as the Primary DNS and Secondary DNS provided by your

Internet Service Provider. You may also be required to enter the MAC address in some

cases depending if your ISP requires. When complete entering, please click “Save” at

bottom of this page to save and complete your basic setup.

Static user in Setup

When selecting “Static IP” as your internet connection method, you will need to enter WAN IP

address, Subnet Mask, Default Gateway, and Static DNS provided by your Internet Service

Provider. When complete entering, please click “Save” at bottom of this page to save and

complete your basic setup.

5. After WAN/Internet Setting, if you need Wireless settings, please going down the same

page. You can see wireless setting as pictures below. At the bottom, enable “Wireless

Security” to select your preferred “Security Mode”, if you need. Please remember to “Save”

your changes. The Default SSID is CW-5358U and you could change by yourself!

3. DualWan : Setting WAN2

Do not enable WAN2, if you have only single WAN line

If you have 2 different lines from Internet service providers, you can enable the WAN2 and select the type of connection. (the same process of setup as WAN1)

After setting WAN2, please remember to enter the WAN1:WAN2 Weight. The larger

number, the higher the priority. Ex: If you have 10M for WAN1 and 1M for WAN2 ADSL lines, you should set 10:1

Please click “Save” at bottom of this page to save and complete your basic setup and make sure you plug the line to LAN1 (WAN2) port 4. Checking Internet Connection:

After Wireless Router’s basic setting, please click “Status”.

Using PPPoE as an example, upon connecting to the internet, you should be able to see

updated information on your IP address, Subnet Mask, Default Gateway, Primary DNS,

and/or Secondary DNS which gathered from your modem by your wireless router. This means

your internet connect is now ready to use.

USB Application BitTorrent Client

This downloader is a cross-platform BitTorrent client, which allows users to download BT files without PC.

CW-5358U has only 32MB RAM, if you are a heavy user for BT, please use

SWAP to increase memory for Router. Please see page 15 for SWAP guide

For applying BT Cilent (Downloader), Please: 1. Make sure CW-5358U’s internet has been set successfully and connecting. 2. Prepare a spare USB flash drive 3. Plug the USB into CW-5358U and power on it. 4. Browse 192.168.11.1 on Web browser (IE or Firefox) and Click USB and NAS

function.

5. Check (Tick) to enable ALL necessary USB function, besides Bidirectional copying. Then, Save it.

6. Check the USB and NAS page is as following

7. Click BitTorrent Client and you must do this step manually 8. Click BitTorrent Client and you must check the following steps

i. Enable torrent client ii. Enable Keep alive iii. Check the right Download directory and enter the PATH (Please Check

the the bottom of USB support page and the Attached device. It shows the right PATH)

iv. Download directory: /tmp/mnt/sda1 (default), please confirm with the bottom of USB Support page.

v. Enable Use .incomplete/ vi. Enable GUI vii. If you do not need, please remain Authentication required unticked. If

you enable, please input password! Default username is “admin” password is “ ” (blank)

viii. Please Enalbe all Download/upload/ratio limit, this will keep the router’s LOADING.

ix. Enable queuing (download 2 files at a time is recommended) x. Please Click Save

Please Check the Picture below

For Using BT Downloader, Please: 1. Start : Click USB and NAS>BitTorrent Cliet> Remote Access [Click here to open Transmission GUI] or Open your web browser (IE or Firefox) and enter http:// Router IP Address:9091/ to control BT downloader. For example: http://192.168.11.1:9091. You will see following on the screen.

2. Uploading torrent file: Please click “OPEN” and “Browse” to your torrent file in your computer. Then, click “Upload”. (CW-5358U is not as good as PC, five more missions may cause CW-5358U becomes slow or even shut down)

Do not upload file larger than your free space of USB device. After uploading the file, please wait 5 minutes before uploading another.

If you see any error from about “tracker”. The downloading is continuing! (see

picture bellow)

You may click “refresh” on you IE if there is any error message to get

information renew.

If you’d like to unmount USB, please make sure you click “Pause” for all

missions from BT downloader web page. It will verify missions once you

restart. 3. Preference Setting: At the left bottom of the screen (see picture above), you could click to adjust the preference setting. Click Inspector at the right top, you can see the information of missions.

4. Getting file: After downloading, please go to http://192.168.11.1 , Click USB and NAS. Find the right bottom of the screen and click “Unmount” as following. Then, you could unplug you USB device from CW-5358U and plug in your computer to get the file.

5. Deleting file: Right-Click the file on your screen, you will see screen as following. Please choose “Trash Data & Remove From List” to completely delete the file from USB device.

If mission stay still for a while (caused by disconnected from internet or other causes), you may click “Verifying Local Data” (see above) to refresh the mission. 3. Computer Setup

(Optional: If any problem occurs, you might check your computer setup) 1. After connecting your computer’s LAN port with CW-5358U. Please Click START, then choose Connect To and open Show all connections.

2. Upon opening Network Connections, right click on your Local Area Connection and

select Properties.

3. Left Click on Internet Protocol (TCP/IP) in the new popup window, and select Properties.

4. When Internet Protocol (TCP/IP) Properties popup, first click on Use the following IP address. Then type in as follows:

IP address: 192.168.11.xxx (1<xxx<255) Subnet mask: 255.255.255.0 Default gateway: 192.168.11.1

Then click on Use the following DNS server addresses:

Preferred DNS server: 192.168.11.1

4. When done, please click OK twice to complete.

Troubleshooting

Q: How to enable Telnet function in Windows Vista and 7?

By default, Telnet is not installed with Windows Vista and Windows 7, but you can install it by

following the steps below.

To install Telnet Client:

1. Click the Start button, click Control Panel, click Programs, and then click Turn Windows

features on or off. If you are prompted for an administrator password or confirmation, type the

password or provide confirmation.

2. In the Windows Features dialog box, select the Telnet Client check box.

3. Click OK. The installation might take several minutes.

4. Please Restart the BT downloader Installation again

Q: If I upload the file larger than free space and it keeps showing error message, what

should I do? (See following)

1. Refresh your Browser. ( This will fixed the most situation)

Q: If the torrent file is wrong or broken, it might cause error message “connection

Failed” on BT downloader. (See above picture) What should I do?

Please turn off CW-5358U and unplug the USB device from CW-5358U. Plug the USB device

on your pc. Then, please delete the over-sized file from “download” folder and “torrents” folder.

The BT downloader will be recovery when you plug USB back to CW-5358U

Q: What if I plug USB switch to extend the USB ports?

Sorry, the router only consumes limited power. It is not enough to extend USB ports by switch.

Q: How do I RESET my CW-5358U? 1. Reset Button: For bringing the device back to factory default setup. Please use sharp and pointing item to press the Default button for about 10 seconds to restore back to factory setup. 2. Software Reset: Launch 192.168.11.1 and Administration page. By clicking the

“configuration” and goto “Restore Default Configuration”, then select “Restore router default

settings”. Your CW-5358U will start restore back to factory default setting. Please do not

remove power when Router is resetting.

Q: I cannot see or access the Login screen in the Web Management page.

A: Make sure you are using the correct IP address. You can also try below methods.

The default IP address is 192.168.11.1.

If you changed the default IP address, please use your changed IP address.

If you changed the IP address and have forgotten it, see the Question 1 on how

to find the IP address of your CW-5358U.

Reset the device to its factory defaults, and try to access the CW-5358U with

the default IP address

If the problem continues, contact the network administrator or cd-r king.

Q: What other versions of Tomato could I upload?

A: Highly recommend only upload the firmware provided by cd-rking. Please ask our engineer

before you upload unknown versions of Tomato firmware!

Use other firmware might cause the router malfunction.

Q: What is SWAP:

Swap space in Linux is used when the amount of physical memory (RAM) is full. If the system

needs more memory resources and the RAM is full, inactive pages in memory are moved to

the swap space. While swap space can help machines with a small amount of RAM, it should

not be considered a replacement for more RAM. Swap space is located on hard drives, which

have a slower access time than physical memory.

Q: When should I SWAP memory?

While you use this router as a NAS device or BT downloader, you can borrow sdram from your

hard disk through CW-5356/5358 USB port.

The steps of how to SWAP memory for router:

CAUTION: Make SWAP memory will format your USB flash or HDD disk !!

STEP 1~~

Please untick the automount , and unmount your USB storage from web GUI first. Then

Plug you USB Disk on router. (see below picture)

STEP 2~~ Click Start>RUN> and type cmd <enter>

STEP 3~~ Telnet 192.168.11.1 <Enter> unknown login:root <Enter>

Password:admin)

STEP 4. fdisk /dev/sda <Enter>

STEP 5. delete partition: d <Enter> 1<Enter>

STEP 6. Create swap(512M): n <Enter> p <Enter> 2 <Enter> 1<Enter> +512M

<Enter> t <Enter> 82 <Enter>

STEP 7. Create data: n <Enter> p <Enter> 1<Enter> <Enter> <Enter>

STEP 8. Choose formation of storage: t <Enter>1 <Enter> b (FAT32)

If you need Linux formation, you could type 83 (ext2/ext3) instead of b

STEP 9. Exit: w <Enter>

S

1. mkswap /dev/sda2 <Ent

2. swapon /dev/sda2 <Enter>

TEP 10.Activate and make swap:

er>

STEP 11.Activate and make storage partition

ows formation)

NAS>>>then TICK the AUTOMOUNT on the

unt

AVE

1. mkfs.vfat /dev/sda1 (for fat32 Windor mkfs.ext3 /dev/sda1 (for ext3 Linuxformation)

Then go to web GUI 192.168.11.1>>>>USB and

"Run after mounting" script, PASTE the following line:

swapon /dev/sda2 and enable AutomoThen

Click S

Please Click Save and Reboot the Router

PS: If you use ext2/ext3, you need to use samba or ftp to transfer data. (It’s not Windows

formation)

Thank you for purchasing a quality cd-r king Product.