wireless power transfer for electric vehicles …eprints.utem.edu.my/16303/1/wireless power transfer...
TRANSCRIPT
WIRELESS POWER TRANSFER FOR ELECTRIC VEHICLES
AMALUDDIN BIN ZAINUDDIN
This Report Is Submitted In Partial Fulfillment of Requirement for the Bachelor Degree of Electronic Engineering (Computer Engineering)
Fakulti Kejuruteraan Elektronik Dan Kejuruteraan Computer
Universiti Teknikal Malaysia Melaka
June 2015
ii
UNIVERSTI TEKNIKAL MALAYSIA MELAKA
FAKULTI KEJURUTERAAN ELEKTRONIK DAN KEJURUTERAAN KOMPUTER
BORANG PENGESAHAN STATUS LAPORAN
PROJEK SARJANA MUDA II
Tajuk Projek : WIRELESS POWER TRANSFER FOR ELECTRIC VEHICLES
Sesi Pengajian : 1 4 / 1 5
Saya AMALUDDIN BIN ZAINUDDIN (HURUF BESAR) mengaku membenarkan Laporan Projek Sarjana Muda ini disimpan di Perpustakaan dengan syarat-syarat kegunaan seperti berikut:
1. Laporan adalah hakmilik Universiti Teknikal Malaysia Melaka.
2. Perpustakaan dibenarkan membuat salinan untuk tujuan pengajian sahaja.
3. Perpustakaan dibenarkan membuat salinan laporan ini sebagai bahan pertukaran antara institusi
pengajian tinggi.
4. Sila tandakan ( √ ) :
SULIT*
*(Mengandungi maklumat yang berdarjah keselamatan atau
kepentingan Malaysia seperti yang termaktub di dalam AKTA
RAHSIA RASMI 1972)
TERHAD**
**(Mengandungi maklumat terhad yang telah ditentukan oleh
organisasi/badan di mana penyelidikan dijalankan)
TIDAK TERHAD
Disahkan oleh:
__________________________ ___________________________________
(TANDATANGAN PENULIS) (COP DAN TANDATANGAN PENYELIA)
Tarikh: ……………………….. Tarikh: ………………………..
Tarikh : 12 JUN 2015 Tarikh : 12 JUN 2015
iii
“I declare this report in my own work except for summary and quotes that I have mentioned its sources”
Singnature :
Author’s Name : AMALUDDIN BIN ZAINUDDIN
Date : 12 JUNE 2015
iv
“I hereby declare that I have read this report and in my opinion this report is sufficient in
terms of the scope and quality for the award of Bachelor of Electronic Engineering
(Computer Engineering) With Honours”
Signature :
Supervisor Name : DR NORIHAN BINTI ABDUL HAMID
Date : 12 JUNE 2015
v
Dedicated to
My Beloved Parents,
Zainuddin Bin Mah Jilis and Rohaya Binti Alias,
My supportive supervisor,
Dr Norihan Binti Abdul Hamid
My lovely siblings,
My friends who have encouraged, guided and
inspired me throughout my education journey
vi
ACKNOWLEDGEMENT
First of all, I would like to take this opportunity to express my deepest gratitude to
my project supervisor, Dr Norihan Binti Abdul Hamid for her guidance, encouragement
and endurance the whole course of this project. It is indeed my pleasure for her support,
invaluable advices and enthusiastic toward my project. Your advice on both research as
well as on my career have been priceless.
My special gratitude is to my beloved family, especially my parents Zainuddin Bin
Mah Jilis and Rohaya Binti Alias for their fullest support throughout the year study in
Technical University Malaysia Melaka (UTeM). Because of them, I am the person who I
am today, for all their moral support all these while so that I will be to complete project
successfully. Not forget for my brother, Ahmad Anwar Bin Zainuddin for his guidance in
completing this project.
Last but not least, I would like to give a bunch of thanks to everyone especially to
all my friends who involved directly and indirectly in this project. The encouragement and
support given towards me earning my experience and knowledge are indescribable and
without them, this project and this report would have been impossible.
vii
ABSTRACT
This project is a development of a new approach to charging battery for electric
vehicles using the inductive resonance coupling method. Inductive resonance coupling is
a combination of inductive coupling and resonance frequency produced by the alternator.
The aim of this project is focused on producing suitable power of the receiver coil to
charge electric vehicle’s battery. This project is start through designed and simulation
circuit testing, then the data are collected and analyzed. The device is develop and
presented in prototype. The performance of the charging device is analyzed. The
demonstration of electric car prototype can be charged wirelessly using receiver coil
placed under the car and the transmitter coil on the surface on the ground. However, the
prototype are not able to charge the battery of electric vehicle but power produced are able
to charge any low voltage electronic device such as a smartphone and rechargeable
battery.
viii
ABSTRAK
Projek ini memperkenalkan pendekatan baharu untuk mengecas bateri kenderaan
elektrik dengan menggunakan kaedah gandingan resonans induktif. Gandingan resonans
induktif adalah gabungan antara gandingan induktif dan frekuensi resonans yang
dihasilkan oleh alternator. Matlamat projek ini difokuskan untuk menghasilkan kuasa
yang sesuai untuk mengecas bateri kenderaan elektrik menggunakan teknologi tanpa
wayar. Projek ini bermula melalui percubaan rekaan litar simulasi dan hasil dapatan kajian
ini dikumpul dan dianalisa. Peranti yang dihasilkan dan dipersembahkan dalam bentuk
prototaip. Kemudian, prestasi peranti pengecasan ini dianalisa. Demonstrasi prototaip
kenderaan elektrik yang menggunakan pengecasan tanpa wayar dengan menggunakan
gegelung penerima dipasang di bawah kereta dan gegelung penerima di atas permukaan
jalan. Walaupun prototaip ini tidak mampu untuk mengecas kenderaan elektrik sebenar,
kuasa yang dipindahkan mampu untuk mengecas peranti bervoltan rendah seperti telefon
pintar dan bateri dicas semula.
ix
TABLE OF CONTENTS
CHAPTER TITLE PAGE
PROJECT TITLE I
REPORT STATUS VERIFICATION FORM II
DECLARATION III
SUPERVISOR DECLARATION VI
DEDICATION V
ACKNOWLEDGEMENT VI
ABSTRACT VII
ABSTRAK VIII
TABLE OF CONTENT IX
LIST OF TABLES XIII
LIST OF FIGURES XIV
LIST OF APPENDICES XVII
I INTRODUCTION
1.1 Introduction 1
1.2 Problem Statement 3
1.3 Objectives 4
1.4 Scope of projects 4
1.5 Thesis Outline 5
x
II LITERATURE REVIEW
2.1 Introduction 6
2.2 Wireless Power Transfer Principle 7
2.2.1 Microwave Principle 7
2.2.2 Laser Principle 9
2.2.3 Inductive Resonant Coupling Principle 10
2.2.3.1 Concept of Electromagnetism 11
2.2.3.2 Electromagnetic Induction 12
2.2.3.3 Resonance Frequency 14
2.2.3.4 Definition of Inductor 15
2.3 Comparison of three Principle
In Wireless Power Transfer 16
2.4 Chapter Summary 18
III RESEARCH METHODOLOGY
3.1 Introduction 19
3.2 Electric Vehicle Charging System 20
3.2.1 Circuit Diagram 21
3.3 Methodology and Project Development 22
3.3.1 Methodology Flowchart 23
3.3.2 Circuit Design 25
3.3.3 Simulation and Analysis Circuit on
Breadboard 26
3.3.4 Transistor and Receiver coil 27
xi
3.3.5 Printed Circuit Board (PCB)
Development
3.3.5.1 Layout Design 29
3.3.5.2 Etching Process 30
3.3.5.3 Soldering Process 30
3.3.5.4 Traoubleshooting 30
3.4 Electric Vehicle Prototype Development 31
3.5 Charging Indicator 32
3.6 Component and Device used in Designed Circuit 33
3.7 Chapter Summary 36
IV RESULT AND DISCUSSION
4.1 Introduction 37
4.2 Inductance and Capacitance Value Consideration 38
4.3 Experimental Set Up 40
4.4 Result and Analysis 41
4.4.1 Correlation between distances of transmitter
Circuit and receiver circuit 41
4.4.2 Correlation between of input power
(via transmitter circuit) and output power
(via receiver circuit) in fixed distance of 0 cm 44
4.4.3 Correlation between of input power
(via transmitter circuit) and output power
(via receiver circuit) in fixed distance of 5 cm 47
xii
4.4.4 Correlation between of input power
(via transmitter circuit) and output power
(via receiver circuit) in fixed distance of 10 cm 48
4.4.5 Relationship between of input power
(via transmitter circuit) and output power
(via receiver circuit) in fixed distance of 15 cm 49
4.5 Prototype 50
4.6 Prototype with a different obstacle between
transmitter coil and receiver coil 51
4.7 Result of the circuit prototype demonstration 53
4.8 Electric Vehicle Prototype 54
4.9 Charging Indicator 55
4.10 Chapter Summary 56
VI CONCLUSION AND RECOMMENDATION
5.1 Conclusion 57
5.2 Recommendation 59
REFERENCES 60
APPENDICES 62
xiii
LIST OF TABLES
TABLE TITLE PAGE
2.1 Comparison of advantage and disadvantage of three 16
wireless power transfer method
xiv
LIST OF FIGURES
FIGURE TITLE PAGE
1.1 Example of electric car using plug in cable 3
2.1 Block Diagram of Microwave System 8
2.2 Magnetic field around the wire/conductor 12
2.3 Transformer 13
3.1 Block diagram of the system 20
3.2 Schematic design of transmitter circuit 21
3.3 Schematic design of receiver circuit 21
3.4 Methodology flowchart 23
3.5 Methodology flowchart 24
3.6 Circuit testing using breadboard 26
3.7 Circuit tested using multimeter to check functionality 26
3.8 Transmitter and Receiver coil manufacturing 28
(Multilayer air core Inductor)
3.9 Layout design of transmitter circuit 29
3.10 Layout design of receiver circuit 29
3.11 Acrylic sheet 31
3.12 Toy’s tyre 31
xv
3.13 Charger module with rechargeable battery 31
3.14 Schematic of LCD Circuit Diagram 32
3.15 MAX17043 Fuel Gauge 33
3.16 Toroidal core inductor 34
3.17 IRFZ44N Power MOSFET 35
3.18 Enameled Cooper Wire 35
4.1 Frequency produced by an oscillator 38
4.2 Completed prototype model of wireless 40
power transfer system
4.3 Relationship between output voltages (V) and 41
output current (mA) versus distance
4.4 Relationship between output power (W) and 42
output current (mA) versus distance
4.5 Relationship between output voltages (V) and 44
output current (mA) versus input voltage (V)
4.6 Relationship between input voltages (V) versus 46
efficiency, ŋ % at the distance of 0 cm
4.7 Relationship between output voltages (V) and 47
current (mA) versus input voltage (V) at the
distance of 5 cm
4.8 Relationship between output voltages (V) and c 48
urrent (mA) versus Input Voltage (V) at the
distance of 10 cm
4.9 Relationship between input voltages (V) and 49
current (mA) versus input voltage (V) at the
distance of 15 cm
xvi
4.10 LED light up brightly when the coil is closer 50
4.11 LED dim slightly when the coil is far each other 50
4.12 A pack of soil 51
4.13 A pack of water 51
4.14 Thick book 51
4.15 Correlation between output voltages with 52
different barrier versus distance
4.16 The output of receiver can be used as charger 53
of smartphone
4.17 An electric vehicle prototype integrated with 54
wireless power transfer device
4.18 Charging indicator to show the charging percentage 55
of the battery
xvii
LIST OF APPENDICES
NO TITLE PAGE
A Table of Collected Data 62
G Source Code of Charging Indicator 68
H INOTEK Poster 70
CHAPTER 1
INTRODUCTION
1.1 Introduction
Electricity is a necessity of today modern life. It is difficult to live or passing a day
without electricity. Today, wireless power transfer has been attracting a great deal of
attention. Wireless power transfer is the transmission of electrical energy from a power
source to an electrical load without interconnecting wires. It is used to power on the
electrical devices without the wire. Besides, because of this wireless power, some of the
devices will not require the battery to operate.
2
There is a demand for wireless power transfer system. Nowadays, the development
of wireless charging for smartphone is rapidly increase in market. The drawbacks of the
system is the smartphone are need to attach charging plate but cannot lift it while charging.
In this project, the proposed wireless power transfer technique based on inductive
resonance coupling method. When AC power has been supplied through a coil, magnetic
field will be generated around the coil. At the moment, if another coil put aside it, induced
current will produced and caused the magnetic field will also appear around the other coil.
This is the reason that wireless power transfer is set up between two coils. Energy will be
transfer when both coils will have same resonant frequency.
Many of the contactless feed systems are based on the electromagnetic induction’s
principle. Small distance wireless power transfer is demonstrated through used of
induction. Knowledge of electric circuit logic and electromagnetic theory is important to
realize the practical design. Knowledge of electric circuit logic and electromagnetic theory
is important to realize the practical design.
This project provides a literature review of several wireless power transfer
principle. All the methods that have been used to design wireless power transfer will be
reviewed along with advantage and disadvantage of each principle. This project will
conclude a discussion to choose suitable principle to charge electric vehicle.
3
1.2 Problem Statement
Current technologies only allow electric vehicles to be charged through plug-in
cable. However, the problem occurs when the user need to find the charging point and the
charging cable is lost or damaged. This project is about designing a wireless power
transfer for electric vehicles. The concept of this project is suitable for any electric vehicles
such as bus, car and light train. It will prepare a new convenient way to recharge the battery
of the electric vehicles rather than using the traditional plug-in cable.
With the implementation of wireless power transfer (WPT) in order to charge the
electric vehicle, there is no physical connection or contact between the vehicles and the
power supply. The process is fully automated, whereby no human handling works are
required to perform the charging process. Even though wireless power transfer concept is
well developed and has been applied in industrial application, but its applications in the
transport sector are still emerging.
Furthermore, another serious problem occurred with current plug in cable for
electric vehicles is people tend to get an electrical shock if the cable system is damaged.
With wireless charging approach for electric vehicle can prevent this incident happen
because no wire or cable is required and it’s transfer in electromagnetic form, so that,
people will not get electrical shock in this kind of energy transfer.
Figure 1.1: Example of electric car using plug in cable
4
1.3 Objectives
The objectives of this project is:
To study and investigate on wireless power transfer. A technique used in my
research is an inductive resonance coupling method.
To identify how many power (voltage and current) could transmit from primary
coil (source) to a secondary coil (load).
To design the wireless power transfer for electric vehicles by using the concept of
inductive resonance coupling method. To prove it, a prototype will be built.
1.4 Scope of project
This research focus on developing a new approach of electrical charging using wireless
power transfer.
Study about wireless power transmission using the inductive resonance coupling
method.
Implement the receiver and transmission circuit simulation into the prototype.
Develop the electric vehicles wireless power transfer devices.
Develop the charging indicator using LCD display.
Analyze the prototype through functionality measurement and testing.
5
1.5 Thesis Outline
This outline is divided into five chapters to provide reader to understand the whole
project. It is organized as follows:
Chapter 1, Introduction, covers the overview of the project.
Chapter 2, Literature Review and Background Studies, all the project theory,
perspective, methods that used to solve problem and any hypothesis that related in order
to design the appropriate circuit.
Chapter 3, Research Methodology, the proper procedure in designing and
manufacturing of the system is presented.
Chapter 4, Result and Discussion, the result of all experiments is presented. The
experimental result is discussed and analyzed for future improvement.
Chapter 6, Conclusions and Recommendations, the conclusions of the
experimental result is drawn and future work is recommended.
CHAPTER 2
LITERATURE REVIEW
2.1 Introduction
This chapter encompasses the study of existing research related to the project.
Every information extracted will be analyzed to enhance the understanding of the main
concept all the way through this project. There are three principle used in wireless power
transfer which is microwave, laser and inductive resonance coupling principle. The
fundamental of these method are analyzed and compared in terms of performance. The
suitable principle will be chosen to design wireless charging for electric vehicle.
7
2.2 Wireless Power Transfer Principle
The wireless power transfer is a technology of no wire included in terms of transfer
the energy. Concept of wireless power transfer has been discovered widely since Nikola
Tesla carried out his first experiment about pursuing his idea on wireless lighting and
electrical distribution after successfully invent an alternating current [1]. They are many
methods used in the wireless power transfer which are microwave, laser, and inductive
resonance coupling method.
2.2.1 Microwave Principle
Wireless power transfer by using microwave method has been used more than a
century [1]. It is called as microwave because the characteristics itself which is shorter
wavelength of electromagnetic radiation in microwave range. The limitation of the
wavelength radio is difficult to tune and overall efficiency would be too low for practical
use [1]. The signal transmitted by microwave method will be received by rectenna.
Rectenna is a combination of rectifier and antenna is used to convert the microwave
energy back into electricity. The first rectenna is developed by W. Brown, the pioneer in
wireless power transfer technology in 196.The concept of microwave method is explained
with block diagram shown in figure below [5].