The Easy to Use Deep Cleaner

™

™

SteamVac™ Widepath Deep Cleaner cleans carpet fibersby applying hot tap water and cleaning solution.

Widepath

Congratulations on your purchaseSteamVac Widepath cleaners have 6 rotatingbrushes that deep clean carpets and scrubbare floors!

www.hoovercompany.com

LS MODEL

2

Fill in and RetainThis HOOVER deep cleaner isdesigned for deep cleaning carpet,rugs, carpeted stairs and upholstery.The model and serial numbers arelocated on the data label on the backof the handle.

For your personal records, pleaseenter the COMPLETE model and serialnumbers in the spaces provided andretain this information.

Your deep cleaner is model

and has serial number

It is suggested that you attach yoursales receipt to this owner s manual.

Verification of date of purchase maybe required for warranty service ofyour Hoover product.

IndexImportant safeguards . . . . . . . . . . 2Assembly . . . . . . . . . . . . . . . . . . . 4-5

Carton contents. . . . . . . . . . . . . . 3How to use. . . . . . . . . . . . . . . . . . 6-7

Agitator speed selector . . . . . . . 7Automatic “shut-off” . . . . . . . . . . 7Deep cleaner description . . . . . . 6Emptying the recovery tank . . . . 8Filling the clean solution tank . 7-8

How to cleanAfter cleaning . . . . . . . . . . . . 9-10Before you begin . . . . . . . . . . . . 9Carpet cleaning . . . . . . . . . . . . . 10Cleaning bare floors . . . . . . 10-11Clean Surge Feature . . . . . . . . . 10 Picking up spills . . . . . . . . . . . . 10Using the tools . . . . . . . . . . . . . 11

Attaching tools . . . . . . . . . . . . 11Cleaning carpeted stairs . . 11-12Cleaning upholstery . . . . . . . 12

Scrub module . . . . . . . . . . . . . . 11Maintenance

Headlight replacement . . . . . . . 13If you have a problem . . . . . . . . 13Lubrication . . . . . . . . . . . . . . . . 12Service . . . . . . . . . . . . . . . . . . . 12Storage . . . . . . . . . . . . . . . . . . . 12

Warranty . . . . . . . . . . . . . . . . . . . . 13

I m p o rtant Safeguard s !When using an electrical appliance, always follow basic

precaution, including the following:

WARNING: To reduce the risk of fire, electricshock, or injury:

• Use indoors only.• Use only on surfaces moistened by the cleaning process or small spills. Do

not immerse product.• Connect to a properly grounded outlet only. See “Grounding Instructions”.• Do not clean over floor electrical outlets.• Do not use without tanks in place.• Use extra care when cleaning on stairs.Do not place deep cleaner on stairs.• Use deep cleaner only for its intended use as described in the instructions.• Use only attachments recommended by The Hoover Company; others may

cause hazards.• The use of an extension cord is not recommended. If an extension cord is

absolutely necessary, use at least a 16 gauge 3-wire cord which has a 3-prong grounding type plug and a 3-pole receptacle that accepts the machine plug.

• Unplug deep cleaner when not in use. Turn off all controls before unplugging.• A lw ays disconnect cord from electrical outlet before servicing the deep cl e a n e r.• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.• Never handle plug or appliance with wet hands.• Do not pull or carry by cord, use cord as a handle, close door on cord or pull

cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

• Do not use with damaged cord or plug. If appliance is not working as it should,has been dropped, damaged, left outdoors, or dropped into water, take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer.

• Close supervision is necessary when any appliance is used by or near children. Do not allow deep cleaner to be used as a toy or to run unattended atany time.

• Do not point tools toward people or pets.• Use only commercially available floor cleaners intended for machine

application. Do not use any type of wax with deep cleaner.• To assist In reducing drying time, be certain the area is well ventilated when

using detergents and other cleaners with this machine.• Keep detergents and other cleaners out of children's reach.• Do not use to pick up flammable or combustible liquids such as gasoline or

use in areas where they may be present.• Do not pick up chlorine bleach, drain cleaner, gasoline or any other toxic

material with this appliance.• Do not pick up anything that is burning or smoking, such as cigarettes,

matches, or hot ashes.• Avoid picking up hard, sharp objects with the deep cleaner. They may damage

the machine.• Keep hair, loose clothing, fingers, feet and all parts of body away from

openings and moving parts.• Do not put any object into openings. Do not use with any opening blocked;

keep free of dust, lint, hair, and anything that may reduce air flow.• To help prevent matting and resoiling, avoid contact with carpets until they are

dry. Keep children and pets away from carpets until they are completely dry.• Store in a dry place. Do not expose machine to freezing temperatures.

Save these instru c t i o n s !© 1993, 1999 The Hoover Companyw w w. h o ov e rc o m p a ny. c o m

READ ALL INSTRUCTIONS BEFORE USING APPLI-

Review this manual beforeoperating deep cleaner

Owner’sManual

ENGLISH ➜ pp. 1-14ESPAÑOL ➜ pág. 15-23FRANÇAIS ➜ p. 24-32

3

GroundingInstructions

This appliance must be grounded. If itshould malfunction or breakdown,grounding provides a path of least resis-tance for electrical current to reduce therisk of electric shock. This appliance isequipped with a cord having an equip-ment-grounding conductor (C) andgrounding plug (A). The plug must beplugged into an appropriate outlet (B)that is properly installed and grounded inaccordance with all local codes andordinances.

DANGER-Improper connection of the equipment-grounding conductor can result in therisk of electric shock. Check with a qual-ified electrician or service person if youare in doubt as to whether the outlet isproperly grounded. Do not modify theplug provided with the appliance - if itwill not fit the outlet, have a proper outletinstalled by a qualified electrician. Thisappliance is for use on a nominal 120volt circuit and has a grounding plugthat looks like the plug illustrated insketch (A).

A temporary adapter (D) may be used toconnect this plug to a 2-pole receptacle(E) if a properly grounded outlet is notavailable. The temporary adapter shouldbe used only until a properly groundedoutlet (B) can be installed by a qualifiedelectrician. The green colored rigid ear,lug, or the like (F) extending from theadapter must be connected to a perma-nent ground (G) such as a properlygrounded outlet box cover. Wheneverthe adapter is used, it must be held inplace by a metal screw. NOTE: InCanada, the use of a temporary adapteris not permitted by the CanadianElectrical Code.

A B

C

D F

G

E

1. Assembly

Unpack deep cleaner from the carton and identify theparts shown. Remove and dispose of the packing.

A B

C DE F G

H

I

J

M

N

L K

1-1

A. Deep cleaner B. Upper handle with powered hand tool OR

Upper handle with powered hand tool and scrub module*

C. Bolts (2) D. Nuts (3 - one extra included) E. Carpet/Upholstery Detergent (some have 2 bottles)F. Bare Floor Cleaner*G. PreCleaner* SprayH. Bare floor attachment

Contained in carton with hose:I. HoseJ. Stair/upholstery nozzle K. Tool holder and screw (taped on rack under nozzle)L. Hose holderM. Crevice tool*N. Nozzle cleanout-tool*

*Included with some models

Carton contents

Press cord into cord clip on back ofhandle. Pull cord tight.

4

The assembled cleaner will look like thisdrawing (LS model shown). Assemble handle

1-2

Attach upper handleRemove clean solution tank (upper tank)from deep cleaner.

With cord hook (A) to back of deep cleaner,push upper handle down onto lower han-dle. Push b o l t s into holes on f ront of han-d l e. If bolts will not go through hole easi-ly handle is not pushed completelyd ow n .

1-3

1-5 1-6

1-7

Attach hose holderPosition hose holder (B) onto handle bymatching tabs on rack with openings onback of handle. Make sure holes forbolts are aligned.

1-4

1-8 1 - 9

Place nuts in recessed areas on back ofhandle. Hold each nut in place whiletightening each bolt securely (from thefront of the handle) with a Phillips screwdriver.

Only two nuts are needed on this model.The extra nut is not required but hasbeen provided for your convenience.

A

C

DB

When handle sections are completelytogether, squeeze trigger (C) anddepress Clean Surge™ Button (D) onupper handle to snap trigger rod inplace.

Replace clean solution tank (upper tank)by positioning bottom first. Press ontank handle to snap top of tank intoplace.

Attach tool holderRemove tool and taped screw from holder.Insert projections on holder into slots onback of cleaner.

5

1 - 1 0 1 - 1 1 1 - 1 2

1 - 1 3 1 - 1 4 1 - 1 5

Slide rack down into place. Insert screwat (E) and tighten with a Phillips screw-driver.

Storing hose & toolsStore hose on holder by first positioninghose in front section of holder.

E

F

Then continue wrapping hose as shownsnapping end of hose connector intoholder.

Slide crevice tool (F) into holder.Position stair/upholstery nozzle in holderat base of cleaner and snap it into placeas shown at arrow.

Insert end of bare floor attachment intoholder and snap into clip as shown.

Powered hand toolThe powered hand tool is shipped in aplastic bag for protection. Remove thebag before using the tool by first open-ing tool door.

To remove powered hand tool (G), pull itdown and outward. To reposition the tool, reverse this proce-dure.To remove the scrub module* (H), graspit at the sides and pull it forward. To reposition module, fit tabs in the stor-age area into holes on back of module.Push module to snap it securely intoposition. *included with some models

How to reattach toolcoverThe tool cover is designed with a break-away feature which allows it to snap freeif it is pushed open too far.

To reattach, align hinges of cover withholes on sides of tool storage area.

1 - 1 7

G

H1 - 1 6

6

1. Hand grip2. Solution trigger: press to

release clean solution.3. Clean Surge™ button4. Hose5. Hose holder: wrap hose

around holder and top hose hook (6) for storage.

6. Hose hook7. Cord hooks: wrap cord

around hooks for storage. The top hook can be rotated right or left for quick and easy cord release.

8. Scrub module*9. Powered hand tool10. Carrying handle11. Clean solution tank handle12. Clean solution tank cap/

measuring cup13. Clean solution tank: holds

cleaning solution.14. Recovery tank handle:

raise handle to unlock tank for removal; lower handle forward to lock tank into position.

15. Recovery tank: holds dirty solution.

2. How to useThe assembled deep cleaner will look like the drawing.

2-1

2-2

16. Brush speed selector:slide selector to set brush speed on HI, LO, or OFF.

17. Hood18. Headlight: on both sides of

the hood19. Edge bristles: on both sides

of the hood for cleaning close to edges of carpet.

20. Nozzle21. Cleaning mode indicator:

shows either floor or tool usage

22. ON/OFF pedal23. Handle release pedal: step

on pedal to lower handle to operating (floor) position;

24. Stair/upholstery nozzle 25. Crevice tool26. Bare floor attachment

*Included with some models

This deep cleaner is intendedfor household use.

Operate deep cleaner only at voltage specified on data plate on back of cleaner.Plug deep cleaner into a properly grounded outlet.

ON/OFF pedal &Handle release pedalStep on pedal (A) to turn deep cleaneron. Step on pedal again to turn deepcleaner off.

Step on pedal (B) to lower handle tooperating position. Handle does not lockinto a single position but “floats” to allowconvenient operation.

A B

C

D

Cleaning mode indicatorIndicator will show a green window nextto FLOOR (C) when handle is in theoperating position for cleaning carpetrugs and bare floors.Indicator will show a green window nextto TOOL (D) when handle is in theupright position for tool use on stairs,upholstery, etc.Deep cleaner automatically divertssuction from FLOOR to TOOL whenhandle is raised from the operating tothe upright position.

To transportTo move your deep cleaner from room toroom put handle in upright and lockedposition tilt deep cleaner back onwheels and push forward.

2-3 2-4

1

2 3

48

6

57

7

910

11

12

13

14

15

17

16

18

18

20

21

1922

23

25

24

26

Deep Cleaner Description

7

The deep cleaner may also be lifted byplacing a hand under the upper cleansolution tank handle as shown.

2-5 2-6 2-7

2-8

Automatic “shut off”When the re c o v e ry tank (lower tank) is fullthe automatic shutoff mechanism will shuto ff the deep cleaner suction (suction willbe noticeably reduced).At that time the yellow float disk will riseto the top of the recovery tank lid (E).The deep cleaner will no longer pick updirty solution and the motor sound willbecome noticeably higher in pitch.

When this happens turn deep cleaneroff and empty recovery tank beforecontinuing use.Check clean solution tank also; it mayneed to be refilled.Do not use without float and floatretainer in place. If broken or dis-lodged, take to an Authorized HooverService Center or Dealer for repair.

E

B rush speed selectorYour ‘SteamVac’ deep cleaner has threeagitator brush settings.Hl - for normal cleaning of carpet andbare floorsLO - for gentle cleaning of carpets andbare floorsOFF - for cleaning carpets and barefloors when brushing is not desired.(Such as when picking up liquid spills.See page 10.)Slide selector button to the desired set-ting before cleaning.

The tanksClean solution tank(upper tank) The clean solution tank holds the clean-ing solution that is to be dispersed ontothe surface to be cleaned.

How to fillDisconnect deep cleaner from electrical outlet.Place deep cleaner handle in theupright, locked position.To remove tank, press down on tankhandle and pull forward.

Continued ➜

2-9 2-10

Carry tank to a sink. Rotate tank cap counterclockwise andlift up to remove cap.

5 OUNCES/150 ml

A

Turn cap (A) upside down to serve as ameasuring cup.Using cap, measure detergent followingthe chart below.For carpet, carpeted stairs and uphol-stery:Fill cap to fill line (5 ounces) with HOOVERC a r p e t / U p h o l s t e ry Deterge n t .For bare floors :Fill cap to fill line (5 ounces) with HOOVERBare Floor Cleaner*Do not use Bare Floor Cleaner on carpet oru p h o l s t e ry. Do not use any type of waxwith your ‘ S t e a m Va c ’Widepath deepcl e a n e r.

For heavy traffic areas:Pre-treat with HOOVER PreCleaner*Spray.If you do not have access to thePreCleaner Spray, double the amountof HOOVER Detergent (use 2 capfulsor 10 ounces per 1 gallon tank).

*Available at additional cost if notincluded with your model.

8

D

C

2-11 2-12

2-13 2-14

2-15 2-16

Pour detergent into tank. Fill tank tofill line (B) (1 gallon) with hot tapwater.

To assure proper performance, use onlyHOOVER cleaning detergent.

B

If rubber ring (C) on cap has becomedislodged, reposition it with unevenside against ledge (D) as shown.

Replace cap. Rotate cap clockwiseuntil it locks In place. Cap must belocked In place for proper perfor-mance and to prevent leaking.

Position bottom of tank into unit andpress on tank handle to snap tank intoplace.

Recovery tank(lower tank)The recovery tank holds the dirty solu-tion that is picked up from the carpet.When the recovery tank is full, the auto-matic shut-off will engage (see page 7)and the tank must be emptied.How to emptyTurn deep cleaner off and disconnectfrom electrical outlet.To prevent possible leaking, removeclean solution tank (Fig.2-8) by pressingdown on tank handle and pulling for-ward; set tank aside (do not set tankon furniture).Step on handle release pedal (Fig. 2-2)and lower handle until it rests on thefloor.

Raise handle to carrying position(straight up) to unlock tank from base ofdeep cleaner. Lift tank from deep clean-er and carry it to a sink or drain.

To remove tank lid, lower handle com-pletely toward back of tank and lift offlid.Empty the tank and reposition the lid.

UNLOCK

LOCK

For full suction, it is important thatthe recovery tank lid is properlysecured before cleaning.

Raise tank handle to carrying position toplace it into base of deep cleaner. Movehandle completely forward to lock tankinto place (see Fig. 2-15).

Raise handle of deep cleaner to uprightposition and reposition upper cleansolution tank.

NOTE: Use only HOOVER detergents.They are specially formulated for usewith your ‘SteamVac’ deep cleaner.CAUTION: Detergents containAnionic and Nonionic Surfactants.Avoid contact with eyes and skin. Incase of contact with eyes, flush withcold water for 15 minutes. In case ofcontact with skin, wash with water. IfIrritation persists, call a physician.For Medical Information (U.S.) call 1-800-752-7869.

9

3-1

3-2 3-3

3. How to cleanBefore you begincleaninga. Vacuum thoroughly - For carpet, usea HOOVER vacuum cleaner with an agi-tator for best results. Vacuum upholsterywith a vacuum cleaner with cleaningtool attachments. Use a crevice tool toreach into tufts and folds. Do not usethe ‘SteamVac’deep cleaner as a dryvacuum cleaner.b. For upholstery, check cleaningcode - Use your HOOVER ‘SteamVac’Widepath deep cleaner only if theupholstery fabric is marked with a “W”(for “wet” clean) or “S/W” (for“solvent/dry” or “wet” clean). Do notclean fabric marked “S” (“solvent/dry”clean only). If your upholstery does nothave a code, seek professional assis-tance.c .Test for colorfastness - Mix deterg e n tand water according to the instru c t i o n s

under “Fill clean solution tank”, Figs. 2-8 to2--14. Wet a white absorbent cloth with thesolution. In a small, hidden area, gently ru bthe surface with the dampened cloth. Wa i tten minutes and check for color removal orbleed with white paper towel or cloth. If sur-face has more than one color, check all col-o r s .d.When cleaning entire floor, movefurniture out of area to be cleaned(may not be necessary if only high trafficareas are to be cleaned). For furnituretoo heavy to move, place aluminum foilor wax paper under legs. This will pre-vent wood finishes from staining carpet.Pin up furniture skirts and draperies.e. Pretreat spots and heavy trafficareas with HOOVER® PreCleaner*- Test PreCleaner for colorfastness by firstspraying it on a hidden area; wait tenminutes and blot with white paper towelsor cloth.If no color change is visible, sprayP reCleaner onto spots and traffic are a s .Wait at least ten minutes. Use your‘ S t e a m Vac’ Widepath deep cleaner to pickup PreCleaner and spot. Repeat until spotis removed; carefully scrub with a house-hold scrub brush if necessary.

Do not saturate carpet or upholstery withP re C l e a n e r.If you do not have access to thePreCleaner Spray, double the amountof HOOVER Detergent (use 2 capfulsor 10 oz. per 1 gallon) in the cleansolution tank.No cleaning solution removes all stains fro mall carpets. Stain removal varies with thetype of spill, time elapsed before re m o v a l ,carpet material, and carpet type.f.To prevent staining, use plastic or alu-minum foil to protect wood or metal sur-faces from possible water spray.g .To avoid wetting and possible damageto wood floors underneath area rugs/car-p e t , e i t h e r move area rugs/ carpet to a non-wood bare floor surface o r place waterpro o fmaterial (e.g. plastic) underneath themb e f o re cleaning.* Available at additional cost if not includedwith your model.See pages 10-13 for instructions on variouscleaning tasks.

After cleaninga. Allow carpet or upholstery to dry. Tohelp prevent matting and resoiling thecarpet, keep children and pets awayfrom surface until it is completely dry. Ifit is necessary to walk on damp car-pet, place towels or white cloths on thetraffic areas.If furniture must be replaced before thecarpet is dry, place plastic or aluminumfoil under legs of furniture so metalslides or wood finishes will not stain thecarpet.

b. If desired, the carpet may be rinsed.Rinsing is not necessary for cleaning,but it may improve the surface’s appear-ance after it is dry.If rinsing is desired, be careful not toover-wet the carpet or upholstery.Allow time for carpet or upholstery todry completely between cleaning andrinsing. To rinse, follow the same proce-dure for cleaning only using hot tapwater with no detergent in the upperclean solution tank.c. Empty tanks, rinse with clear waterand let air dry. Rinse the solution tankcap and recovery tank lid and let air dry.

d. Remove lint from filter screen locatedinside recovery tank.

Continued ➜

e. Remove lint from filter screen locatedon bottom of cleaner as follows. Note:When brushes seem to be rotatingslowly, disconnect deep cleaner fromelectical outlet and check and cleanthis screen.Tilt cleaner back so handle rests on floor.Squeeze frame, lift and pull it out. Wipeoff screen and push frame back intoplace.

Return cleaner to upright position.f. If desired, vacuum thoroughly aftercarpet has completely dried. This willhelp reduce any shading left by thedeep cleaner’s brushes.

To clean nozzleIf lint or other debris becomes lodged innozzle, do not attempt to remove nozzle cover.Pour one to two cups of clear water on anon-carpeted floor. Do not pour wateronto a wood floor.Pick up the water with your deep clean-er. Repeat as necessary until debris isflushed out of nozzle.

Some models have a nozzle clean-outtool for removing debris or if a non-car-peted floor is not available. To use thetool:Disconnect deep cleaner from electri-cal outlet.Slide tool into nozzle and remove debrisas shown.

10

Carpet Cleaning

Picking up spills

Cleaning bare floors

To clean the outside of the machine,wipe off dirt with a cloth dampened inwarm water and mild detergent. Do notuse solvent or petroleum based prod-ucts to clean the machine.

3-4

3-7

Read “Before you begin cleaning”instructions on page 9.1. Fill clean solution tank (upper tank)with HOOVER Carpet/UpholsteryDetergent according to instructions forFigs. 2-8 to 2-14.2. Move speed selector to LO for gen-tle cleaning or Hl for normal cleaning.3. Dry hands and plug cord into a prop-erly grounded outlet.Do not clean over floor electrical out-lets.4. To avoid walking on damp carpet,start at the end of the room farthest fromthe door or path to sink where tanks willbe emptied and filled.Step on handle release pedal and lowerhandle to operating position; turn deepcleaner ON.

5. Squeeze trigger to release cleaningsolution and slowly push deep cleanerforward (equals one wet stroke).

6. Continue to squeeze trigger andslowly pull deep cleaner back towardyou (second wet stroke). Release triggerand slowly push deep cleaner forwardover area just sprayed with solution (drystroke). Then slowly pull deep cleanerback toward you without squeezing trig-ger (dry stroke).

7. Overlap strokes by 1 inch to help pre-vent streaking.

Keep nozzle flat on floor for both for-ward and reverse strokes.8. For heavily soiled areas, use CleanSurge™ button (see following section).To avoid saturating carpet, do not usemore than 4 wet strokes over onearea. Always end with dry strokes.It is best to alternate wet and drystrokes as described above.

For best cleaning results and to aid infaster drying of carpet, end with moredry strokes. (Continue using dry strokesuntil little water is visible passingthrough the recovery tank lid.)Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see“Automatic shut-off”, Fig. 2-6)When finished cleaning, follow “Aftercleaning” instructions on pages 9-10.

Clean Surge™ ButtonThe ‘Clean Surge’ button can be used todispense extra solution when cleaningparticularly soiled areas of carpet or spots.To use, press ‘Clean Surge’ button whilesqueezing solution trigger. For normalsolution spray, release button and contin-ue to squeeze solution trigger.

When picking up spills on bare floors ,use only the floor nozzle with the barefloor attachment in place and speedselector in the OFF position (this will helpp revent spreading the spill).If a spot is left, the stair/upholstery nozzle isgenerally more effective for removing it. Although no cleaning solution can com-pletely remove all spots, they can be tre a t-ed by following the instructions pro v i d e dby the manufacturer of the carpet, uphol-s t e ry, or bare floor surface being cleaned.Do not use the deep cleaner to pick upf l a m m a ble or combu s t i ble liquids orch e m i c a l s .When finished, follow “After cleaning”i n s t ructions on pages 9-10.

How to attach bare floorattachmentDisconnect deep cleaner from electri-cal outlet.To prevent possible leaking, removeclean solution tank (Fig. 2-8) and recov-ery tank (Fig. 2-15) before positioningbare floor attachment.Set tanks aside (do not set tank on furni-ture).1. With handle in upright position, tiltcleaner back so that handle rests on thefloor.

2. With foam strip (A) (located under thenetting) in position as shown, placeattachment on front of nozzle (B).Make sure arrow on end of attachmentpoints in the direction as shown.

3. Push attachment against nozzle whilerotating attachment downward until bothends snap into place.( N o t e : Some fo rce may be required torotate and snap attachment into place. )

3-5Your deep cleaner may also be used topick up small liquid spills (1 gallon orless, never to exceed 1/4 inch indepth) on carpet, upholstery, or barefloors.1. For best results, pick up spills imme-diately by placing the stair/upholsterynozzle just above the spill and suctionup any residue on top of the carpet. 2. If the spill remains, place either thestair/ upholstery nozzle or floor nozzlewith brushes turned OFF in front of thespill, pull the nozzle very slowly over thespill initially with suction only.Repeat with spray and suction.

3-6

A

B

Using the tools

3-8

3-10

4. Return deep cleaner to upright posi-tion. Lower handle and replace recoverytank.5. Raise handle to upright position andreposition clean solution tank.

To clean floorRead “Before you begin cleaning”instructions on page 9.

Do not use the deep cleaner on hard-wood floors.1. Fill clean solution tank with HOOVERBare Floor Cleaner* according toinstructions for Figs. 2-8 to 2-14.Do not use any type of wax with yourdeep cleaner.2. Move speed selector to the Lo or Hlposition for scrubbing or OFF ifscrubbing is not desired.3. Dry hands and plug deep cleanerinto a properly grounded outlet.4. Step on handle release pedal andlower handle to operating position; turndeep cleaner ON.5. To release solution, press trigger.Slowly move deep cleaner forward andbackward over area to be cleaned.

6. To pick up dirty solution, release trig-ger and slowly move deep cleaner overarea where solution has just been dis-persed. Use both forward and reversestrokes.7. Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see “Automaticshut-off”, Fig.2-6)8. When finished cleaning, follow “Aftercleaning” instructions on pages 9-10.Disconnect deep cleaner freom elec-trical outlet and remove attachmentfrom nozzle. Rinse it in clear water. Donot remove plastic screen or foamfrom attachment.*available at additional cost if not includ-ed with your model

Your model includes some combinationof the following tools.A. Powered hand tool has rotatingbrushes for extra scrubbing action onsmall carpet areas, carpeted stairs andupholstery. For some models, thebrushes can be removed for convertingto the scrub module.

C

E

D

With a little solution, test the scrubtool on a hidden area before using onthe desired surface. If no surfacechange is visible, continue to use asdescribed below.1. Fill clean solution tank with HOOVERBare Floor Cleaner* according toinstructions for Figs. 2-8 to 2-14.2. Hold scrub tool above area to becleaned and press trigger to dispensesolution.3. Release trigger and scrub area withtool. Pick up dirty solution withsqueegee as shown.*included with some models

After using scrub tool

Continued ➜

3-9

B. Stair/upholstery nozzle has a built-inbrush to help provide the scrubbingaction some spots may need forremoval.C. Scrub module with detachablescrub pad* attaches to the base of thepowered hand tool (in place of brushmodule). Can be used to scrub stubbornareas such as scuff marks, dried spills,and in hard to reach areas on hard sur-faces.

D. Crevice tool* can be used to cleanalong edges of carpet, carpeted stairsand on upholstery.

*some models

How to attach toolsDisconnect deep cleaner from electri-cal outlet.1. Place handle in upright position andremove hose from rack.All tools attach to the hose in the samemanner:2. Connect tool to hose by sliding it ontoconnector until the tab (C) locks itsecurely.Using your thumb, push forward and upon the latch (D) to remove tool asshown.

Before using toolIt may be necessary to remove air fromthe system (“prime the pump”) so theclean solution will flow to the tool. Followthese steps:1. Attach tool to hose and turn the deepcleaner ON.2. Put the tool on a hard surface oragainst your hand to block off the suc-tion.3. Wait a few seconds (can take up to 15

seconds). Then squeeze the trigger andbegin cleaning.Follow the instructions on pages 12-13for the appropriate cleaning task.

Attaching scrub module*1. Open the tool door and remove thepowered hand tool.2. Grasp the sides of the brush moduleand lift it from the base (E).3. Pull scrub module from deep cleanerand snap it onto the base.Note: It may be necessary to rotate thescrub module (F) slightly so it will alignproperly to the base.

Using the scrub tool

11

3-11

A

B

C

D

F

3-16

12

3-13 3-14

3-15

1. Follow steps a and b for “After clean-ing” on page 9.2. Rinse tool and hose by filling sinkwith a small amount of water. Turndeep cleaner ON and pickup the waterwith the tool.3. Drain hose by turning deep cleaner

ON and holding end of hose up for sev-eral seconds. Do not press trigger.4. Disconnect deep cleaner from electri-cal outlet.5. Drain solution tube (located insidehose) by pointing end of hose in sinkand pressing trigger.6. Proceed with steps c, d, and e, for“After cleaning” on page 9.

Cleaning carpetedstairs

Read “Before you begin cleaning”instructions on page 9.1. Place handle in upright position.Agitator brushes will not rotate whilehandle is in upright position.2. Fill clean solution tank with HOOVERCarpet/Upholstery Detergent accordingto instructions for Figs. 2-8 to 2-14. 3. Attach tool to end of hose. 4. Hose length may require that machinebe placed at the top of the stairs toclean upper half of stairway and at bot-tom of stairs to clean lower half. To prevent machine from falling, useextra caution when cleaning on stairs.Do not place deep cleaner on stairs.Do not point tools toward people orpets.5. Dry hands and plug deep cleaner intoa properly grounded outlet.6. Turn deep cleaner ON. If necessary,refer to “Before using tool” section toremove air from the system.

7. Pre-spray the carpeted stair by hold-ing the tool (A) or (B) about one inchabove the carpet and push it forwardwhile pressing the trigger (equals onewet stroke). 8. Position tool against the riser and slightlyp ress it into carpet pile. Press the trigger andpull the tool s l ow ly over the carpet (secondwet stroke). Release trigger at end of stroke.

9. Lift tool, and position it against riser.Pull tool slowly over carpet withoutpressing trigger (dry stroke). It is best to alternate wet and dry strokesas described above. End with more drystrokes to aid in faster drying of carpet. 10. Overlap strokes by 1/2 inch to helpprevent streaking. To avoid saturating carpet, do not usemore than 4 wet strokes over any onearea. Always end with dry strokes.If additional cleaning is necessary, waituntil the carpet is completely dry beforeusing the tool again. 11. Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see “Automaticshut-off”, Fig. 2-6).When finished cleaning, follow “Aftercleaning” instructions on page 9 and“After using tool” instructions on page 12.

To clean scrub pad, pull it off module.Wash it in water with mild detergent.Rinse and let air dry.Pad must be completely dry before reat-taching to module and storing on deepcleaner.Replacement pads may also be pur-chased. Ask for HOOVER part no.40308001.To store scub module, remove scrubmodule from tool in same manner asremoving the brush module.Align openings on back of module withtabs in storage area (G). Push module into position.After using tool

3-12

G

13

3-17 3-18

Read “Before you begin cleaning”instructions on page 9.Be sure to check the cleaning code onyour upholstery. Use your deep cleaneronly on upholstery marked “W” or“W/S”.1. Place handle in upright position.Agitator brushes will not rotate whilehandle is in upright position.2. Fill clean solution tank with HOOVERCarpet/Upholstery Detergent accordingto instructions for Figs. 2a-8 to 2-14. 3. Attach tool to end of hose.Do not point tools toward people orpets.4. Dry hands and plug deep cleaner intoa properly grounded outlet.5. Turn deep cleaner ON. If necessary,refer to “Before using tool” section toremove air from the system. 6. Gently press the tool onto the fabric.

Cleaning upholstery

Press the trigger and slowly pull the noz-zle over the fabric.7. Overlap strokes by 1/2 inch to helpprevent streaking.Make additional strokes without pressingthe trigger to remove more moisture.8. To clean in corners or creases, lift thetool one-half inch from the fabric andpress the solution trigger. The crevicetool (included in some models) is veryuseful for this task.9.Vacuum up the solution with the toolwithout pressing the trigger.10. For heavily soiled areas, it may be

necessary to repeat the cleaningprocess. Make crisscrossing strokes tothe original pattern; overlap each pass.Make no more than 2 passes with thesolution over any one area to preventover-wetting and damage to fabric.If additional cleaning is necessary, waituntil the upholstery is completely drybefore using the tool again.11. Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see “Automaticshut-off”, Fig. 2-6).When finished cleaning, follow “Aftercleaning” instructions on page 9 and“After using tool” instructions on page 12.

H e a d l i g h tre p l a c e m e n t

What to buyThe deep cleaner uses a 7 volt, wedgebase type bulb, H O OVER part no.2 7 3 1 3 1 0 6 .

W h e re to buyBulbs may be purchased from autho-rized Hoover dealers (Depot), HooverF a c t o ry Service Centers, or through TheHoover Company online atw w w. h o o v e rc o m p a n y. c o m

S t o r a g eBefore storing:

• Empty solution tank and rinse thoroughly with clean water.

• Replace empty solution tank and turn deep cleaner ON. Squeeze trigger and push deep cleaner for-ward and back several times to expel any solution remaining in thedeep cleaner’s system. (Do not usedeep cleaner on wood floors.)

• Empty recovery tank and rinse thoroughly with clean water.

Allow brushes and underside of deepcleaner to air dry thoroughly beforestoring deep cleaner on a carpeted orwood surface.Do not store deep cleaner with a fullsolution tank in place.

LubricationThe motor is equipped with bearingswhich contain sufficient lubrication forthe life of the motor. The addition oflubricant could cause damage. Do notadd lubricant to motor bearings.

4-1 4-24. Maintenance

How to re p l a c eTurn cleaner off and with dry hands,disconnect deep cleaner from electri-cal outlet.1. Using a Phillips scre w d r i v e r, re m o v ethe screw as shown and lift off lens.

2. Pull old bulb straight out of socket. 3. Push new bulb straight into socket untillocked into place.Excessive fo rce is not required.Reposition lens and secure with scre w.

14

ServiceTo obtain approved HOOVER serviceand genuine HOOVER parts, locate thenearest Hoover Factory Service Centeror Authorized Hoover WarrantyService Dealer (Depot) by:

•checking the Yellow Pages under Vacuum Cleaners - Household” OR

•checking the list of Factory Service Centers provided with this cleaner OR -

•calling 1-800-944-9200 for an automated referral of authorized service outlet locations (U.S. only)OR-

• checking the Service section of TheHoover Company on-line at www.hoovercompany.com

Do not send your cleaner to The HooverCompany in North Canton for service,this will only result in delay.If further assistance is needed, contactThe Hoover Company ConsumerResponse Center, North Canton, Ohio44720 Phone: 330-499-9499.In Canada, contact Hoover Canada,Burlington, Ontario L7R 4A8, Phone: 1-800-263-6376.Always identify your cleaner by the com-plete model number when requestinginformation or ordering parts. (Thtom

Problem: Machine won’t run

Problem: Low suction

Problem: Clean solution won’t

dispense

P ro bl e m : Brushes won’t rotate duringfloor cl e a n i n g

4. If you have aproblemIf a minor problem occurs, it usually canbe solved quite easily when the cause isfound by using the check list below.

Full One YearWarranty

(Domestic Use)

Your HOOVER® appliance is warr a n t e din normal household use, in accord a n c ewith the Owner’s Manual against originaldefects in material and workmanship fora period of one full year from date ofp u rchase. This warranty provides, at nocost to you, all labor and parts to placethis appliance in correct operating con-dition during the warranted period. Thisw a rranty applies when the appliance isp u rchased in the United States includingits territories and possessions, or inCanada or from a U. S. MilitaryExchange. Appliances purchased else-w h e re are covered by a limited one yearw a rranty which covers the cost of part so n l y. This warranty does not apply if theappliance is used in a commercial orrental application.

Warranty service can only be obtainedby presenting the appliance to one ofthe following authorized warranty ser-vice outlets. Proof of purchase will berequired before service is rendered.

1. Hoover Factory Service Centers.

2. Hoover Authorized Warranty Service Dealers (Depots).

For an automated referral of autho-rized service outlets in the U.S.A.,phone 1-800-944-9200 ORvisit The Hoover Company on-line atwww.hoovercompany.com

This warranty does not cover pick updelivery, or house calls; however, if youmail your appliance to a Hoover FactoryService Center for warranty service,transportation will be paid one way.

While this warranty gives you specificlegal rights, you may also have otherrights which vary from state to state.

If further assistance is needed, or ifthere are questions concerning this war-ranty or the availability of warranty ser-vice outlets, write or phone theConsumer Response Center, TheHoover Company, 101 East Maple St.,North Canton, Ohio 44720, Phone 1-330-499-9499.

In Canada, contact Hoover Canada,Burlington, Ontario L7R 4A8, 1-800-263-6376.

Possible causePossible solution

• Not firmly plugged in• Plug unit in firmly

• No voltage in wall plug• Check fuse or breaker

• Blown fuse/tripped breaker• Replace fuse/reset breaker

Possible causePossible solution

• Recovery tank full/automatic shut off engaged

• Remove and empty recovery tank

• Blockage in tool on end of hose • Remove tool and clear blockage

• Recovery tank lid not on correctly

• Make sure lid is on securely

Possible causePossible solution• Solution tank not firmly in place • Make sure tank is securely locked in

position • Solution tank empty• Refill tank according to instructions for

surface being cleaned• Recovery tank lid not on

correctly• Make sure lid is firmly in place • Pump needs to be “primed”(when

using tool)• See “Before using tool” section, p.11

Possible causePossible solution• Dirty filter screen on bottom of unit• Clean screen as shown in Fig. 3-2 • Speed selector on OFF • Move speed selector to Low or Hi

HOOVER and are registered trademarksTHE HOOVER COMPANY, NORTH CANTON, OHIO 44720

HOOVER y son marcas registradasTHE HOOVER COMPANY, NORTH CANTON, OHIO 44720

HOOVER et sont des marques déposéesTHE HOOVER COMPANY, NORTH CANTON, OHIO 44720

4-99 F6020/23/24-900 Litho USA 56518-113