welcome to your precept touch - amesburytruth...user guide 40.84.xx.316 and .317 1 1 2 3 6 5 4 1 2 3...

USER GUIDE40.84.XX.316 AND .317

1

1

2

3

6

5

4

123 6

54Notifications Window Position Sensor

Touch Pad Interior Manual Override - Thumb Slide

Exterior Manual Override - Key Cylinder Battery Compartment - 4x AA Battery

WELCOME TO YOUR PRECEPT TOUCH


2

BATTERY INSTALLATION

Unscrew the battery cover.

Insert 4 AA batteries in the bat-tery pack.

Rotate the battery pack handle out and pull to remove battery pack.

Replace the battery cover and tighten thecaptive screw.

Replace battery pack into the handle. Battery pack will only insert fully in the correct orientation.

1

2

A

A

B

C

B

APPS

Navigate to www.myprecept.com/apps

Scan the QR code to download an app for your mobile deviceOR


3

ENROLLING

Open the Precept app and click on the “+” sign in the upper right-hand corner.

Prepare the App

Prepare the Precept Touch

Unlock the handle pushing the manual thumb slide down.

Click on the “Pair a Device” button.

Insert a straightened paper clip into the hole above the mounting screw underneath the thumb slide to press the enroll button.

Read the instructions on screen, Then click on the “Pair a Device” button.

When the handle has finishedcommunicating with your mobiledevice, name your handle on theprompt screen. Then click the“Complete Setup” button at thebottom of your screen.

1

2

A

A

B

B

C

C

Note: If you have any problems setting up your handle, remove the handle from your mobile app, perform a factor reset, and repeat this procedure.


4

OPERATING YOUR PRECEPT TOUCH

A D

B E

C

Ensure the app is running on your mobile device.

Blue spinning: The handle is authenticating with your mobile device.

Red flash: The handle has detected an unauthorized device.

Blue spinning then green flash: The handle has been unlocked.

Bottom solid red: The AA batteries in the handle are low and need to bechanged.

Blue spinning then amber flash: The handle has been locked.

Sides flash red: The lock has jammed.

Magenta flash: Your mobile device is beyond the activation range.

The handle will communicate with your mobile device.

Place your mobile device where you normally carry it.

When the handle is finishedcommunicating with your mobile device, the handle will actuate.

Touch the pad on the exterior of the handle.

Note: As you use the handle, it will learn where you typically carry your mobile device.The handle uses the first ten actuations to train. Ensure your mobile device is in its normal carrying location. For example, in your pocket or purse.

LED ANIMATIONS


5

SYSTEM RESET

A

D

B CUnlock the handle pushing the manual thumb slide down.

The Precept Touch is now ready to be enrolled by a new user.

Insert a straightened paper clip into the hole above the mounting screw underneath the thumb slide to pressthe enroll button.

The handle has a sensor that can determine if your mobile device is inside or outside your door. This prevents unauthorized users from accessing your home while your mobile device is inside.

The handle activity can be viewed with the Precept app or on the web page: www.myprecept.com.

The Precept app can send you customized notifications to monitor a specific user and/or time frame or you can choose the system’s default notifications. The app can notify the user when aneKey holder locks and unlocks the handle.The app will also notify you of low battery and software updates.

The Precept app has an enhanced security feature that can require a pass code to access the mobile app and the touch to open feature. Enabling this se-curity feature allows the app to be protected against unauthorized access when your mobile device isunlocked.On Apple devices, the Touch ID/Face ID can be used in place of the pass code.

Smartphones, and other mobile devices must be Bluetooth Low Energy 4.0 compatible; running iOS 9.0 or higher, or Android OS 5.0 or greater. The Precept app must be installed. Find out if your device is compatible at www.myprecept.com/devices

Hold the button for 10 sec-onds or until the LED ring flashes white.

ADVANCED FEATURES

PRECEPT COMPATABLE DEVICES

INSIDE / OUTSIDE HISTORY LOG

NOTIFICATIONS APP PASSCODE and TWO FACTOR AUTHENTICATION

Perform system reset to make the Precept Touch forget all current eKeys. This might be recom-mended when changing ownership.


6

REGULATORY COMPLIANCE

UNITED STATES of AMERICA

CANADA

Federal Communications Commission (FCC) - Part 15 Sub Part C

FCC Declaration of Conformity - According to 47 CFR, Parts 15.209 and 15.247

Industry Canada Notice and Marking

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party: AmesburyTruth, 5001 West Delbridge Street, Sioux Falls, SD 57107www.amesburytruth.com or 1-800-773-2378

This Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Product: Precept Touch (4513C)

The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.

• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experience radio/TV technician for help.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

Warning: Changes or modifications not expressly approved by AmesburyTruth could void the FCC compliance and negate your authority to operate the product.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.


7

WARNINGS

To ensure compliance with FCC and Industry Canada RF exposure requirements, this device must be installed in a location where the antennas of the device will have a minimum distance of at least 20 cm from all persons. Using higher gain antennas and types of antennas not certified for use with this product is not allowed. The device shall not be co-located with another transmitter.Installez l’appareil en veillant à conserver une distance d’au moins 20 cm entre les éléments rayonnants et les personnes. Cet avertissement de sécurité est conforme aux limites d’exposition définies par la norme CNR-102 at relative aux fréquences radio.To ensure compliance with FCC and Industry Canada RF exposure requirements, this device must be installed in a location where the antennas of the device will have a minimum distance of at least 20 cm from all persons. Using higher gain antennas and types of antennas not certified for use with this product is not allowed. The device shall not be co-located with another transmitter.

RF Radiation Hazard Warning

This product has been designed for indoor use. Operation of channels in the 5150MHz to 5250MHz band and in the 5470MHz to 5725MHz band is permitted indoors only to reduce the potential for harmful interference to co-channel mobile satellite systems.Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage réjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

Indoor Use

Currently, the maximum antenna gain for external antennas is limited to 5.2dBi for operation in the 2400MHz to 2483.5MHz, 5150MHz to 5250MHz and 5725MHz to 5825MHz bands. The antenna gains must not exceed maximum EIRP limits set by the FCC / Industry Canada.Actuellement, le gain d’antenne maximal d’antennes externes est limité à 5.2Dbi pour un fonctionnement en 2400MHz à 2483.5MHz, 5150MHz à 5250MHz et 5725MHz à 5825MHz par points à bandes. L’antenne gains doit pas être supérieure à maximum Eirp limites fixées par la FCC/Industrie Canada.

Maximum Antenna Gain

This radio transmitter (identify by certification number or model number) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.

Alternative

High power radars are allocated as primary users (meaning they have priority) in the 5150MHz to 5250MHz and 5650MHz to 5850MHz bands. These radars could cause interference and/or damage to LELAN devices used in Canada.Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz. Ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

High Power Radars

welcome to your precept touch - amesburytruth...user guide 40.84.xx.316 and .317 1 1 2 3 6 5 4 1 2 3...

Documents