welcome to hrist hurch athedral’s ‘how did they do that ......welcome to hrist hurch...
TRANSCRIPT
Welcome to Christ Church Cathedral’s
‘How Did They Do That?’ Family Trail
Christ Church has teamed up with local makers to create
a fascinating self-guided trail which explores the huge
amount of work and the many materials and methods
that were used to create the Cathedral building and its
priceless collection of artefacts.
Ever wondered how to make stone look like fur, how to
carve wood or the secret to making coloured glass?
Here’s your chance to find out, with help from the ex-
perts.
You can follow this trail in any order you like around the
Cathedral. Directions to each object can be found at the
start of each section.
Entrance
Crypt
Entrance
Baptistery
Quire
Welcome
Desk
Where to find
things...
North
Transept
Carved pulpit
South
Transept
Strongbow’s
Tomb
Chapel
of St
Laud
Stained Glass Windows
These can be found all over the Cathedral — just look up!
Stained glass windows tell stories. They were originally used to teach people who couldn’t read
about the Bible. With sunlight shining through them, casting bright colours around the Cathedral,
they provided quite a show. Almost like an early form of cinema, before films were even thought
of…
What is glass and
how is it made?
Glass is basically molten sand (silica). As
obsidian it occurs naturally in volcanos.
About 7,000 years ago people discovered
that by adding soda ash or potash and lime
to sand they could melt it themselves at a
much lower temperature.
How can you make different
coloured glass?
Coloured glass is produced by adding min-
erals or metal oxides to the glass mix. Cop-
per oxide for example gives blue and green,
and cobalt makes blue-purple. The most
expensive colour is red because you have
to add pure gold to achieve a ruby red. This
was a highly guarded secret.
How do you make a leaded stained
glass window?
To make a large stained glass window a
whole team of highly skilled craftspeople
are involved. First a sketch is drawn to de-
pict a biblical scene or a saint and coloured
in.
Then the cartoon is made, a full-size
sketch, drawn on timber or card
board, showing all the lead lines.
This is copied onto paper and then
cut out to get the patterns for all the
individual pieces of glass.
Then the glass is painted. The traditional meth-
od uses pigments mixed with gum arabic and
water. This is applied in a thin layer to the whole
surface of the glass. When dry, fine brushes are
used to reveal the glass colour underneath again
in places. This is called matting. The painted
glass is then fired in a kiln to make the colours
permanent.
Incredibly fine lines,
textures and shading
can be achieved with
this paint. Just look at
the saints – you can
almost count the hairs
in their beards!
Sometimes details are also etched. A glass piece, col-
oured on one side, is dipped into melted wax. When
the wax is hard, the areas to be etched are scraped
away on the coloured side of the glass. Then it is im-
mersed in acid which eats away the exposed glass.
To assemble all the glass pieces, long lead
channels (cames) are used. The cross section
looks like an H so the glass can slot in on each
side. The cames are draped around all the
glass pieces and cut to size. They are needed
to hold all the pieces of the puzzle in place.
Then the window is soldered together. To prepare for soldering all the
lead joints are cleaned with steel wool and then rubbed with animal fat.
This lets the solder, which is a mixture of tin and lead, flow more easily.
This is a difficult job as too much heat melts away the lead cames or
cracks the glass!
As the glass pieces have different thicknesses the window is
still wobbly after soldering and would let wind and rain
through. So finally, all the tiny spaces and gaps have to be
filled with a leaded cement and are then cleaned and pol-
ished.
The Stained Glass window
is now finished and can
be put in place!
All the windows in Christ Church, apart from one, were designed by the architect George Ed-
mund Street, when he restored the Cathedral in the 1870s. He selected three English stained
glass firms to make the windows and gave them precise guidelines to paint them in the origi-
nal thirteenth-century style.
Contribution by glass artist Gerlinde Kugler
www.gerlinde.ie
Silverware - William III Plate
Go downstairs to the crypt and find the showcase full of large candle-
sticks, bowls and plates towards the back.
This incredible collection of objects was given to the Cathedral by King William III of England
(better known as William of Orange) to celebrate his victory at the Battle of the Boyne in 1690.
At this time the Cathedral also functioned as his personal chapel , when he was in Ireland, and
this amazing altar-ware would have been used on special occasions, when he was here.
These items were made using the tech-niques of
Chasing and Repoussé. These terms are often confused and not
without good reason since the two tech-
niques are often used
together
We might as well think of
slipping and sliding to realise how difficult it is to establish a
clear definition, particular to each process.
In general, repoussé is mainly a 3D or
relief method and chasing is more often a
2D or linear technique.
Another useful division is to think of repoussé as a process that creates relief without significantly altering the thickness of the starting
sheet. The metal is pushed and pulled but its thickness remains
the same. This differs from chasing where the ability of metal to
compress is used to create relief. Some areas remain at their original
height while other areas are compacted to make them lower.
Th
ese
tech
niq
ues
sh
are
sev
eral
pro
per
ties
.
Th
ey c
an b
e w
ork
ed o
n t
iny
jew
elry
pie
ces
or
larg
e sc
ulp
tura
l p
iece
s.
In
bo
th c
ases
ham
mer
s ar
e u
sed
to
pre
ss p
enci
l-li
ke
stee
l t
oo
ls a
gai
nst
met
al,
form
ing
or
com
pre
ssin
g i
t, o
r b
oth
.
Bo
th r
epo
uss
é an
d c
has
ing
can
be
wo
rked
on
all
th
e je
wel
lery
met
als
wit
h e
ase.
H
igh
kara
t g
old
, fin
e s
ilv
er
an
d c
op
per
resp
on
d v
ery
wel
l,
wh
ile p
ale
bra
ss, n
ick
el
silv
er a
nd
ste
el
req
uir
e g
reate
r ef
fort
.
This is the back of the
large plate, showing an ex-ample of repoussé. You can see how the shapes have been hammered out.
This is the right side of
the plate showing both tech-
niques.
Repoussé and chasing both require that the metal be well
anchored on a resistant
surface for working. In both
cases a material called jew-ellers pitch does the job.
It consists of three principle ingredients:
3 parts Pitch - originally a
residue derived from tree resins, but now produced from petrol .
2 parts Binder - brick dust or dry plaster are
added to give the pitch more body.
1 part Lubricant - linseed oil,
beeswax, or tallow are added to make the pitch softer.
These ingredients are blended in a pot at a low heat and stirred with a stick until
well blended. It is possible for pitch to catch fire if it gets too hot so you must
watch the pot at all times!
Remember those torches in Frankenstein movies? They were made of pitch...
Remember those torches in Frankenstein movies? They were made of pitch...
Contribution by silversmith Edward Cook
www.waylandsforge.com
Wood Carving
Make your way to the Quire in the centre of the Cathedral
Take a good look at the intricately carved stalls where the famous Christ Church Cathedral choir sing
and the impressive chair or ‘Cathedra’ where the Archbishop of Dublin sits when he is in the
Cathedral. All this carving dates from the 1870s when the Cathedral was restored.
The Craftsmen who worked
on Christ Cathedral would
have had a deep under-
standing of the materials
they were using. They
would have been appren-
ticed to a Master Wood-
carver for at least 7 years
before they qualified as
working tradesmen.
The apprentice would have
learned many things in
the workshop before he
even touched a piece of
wood - how to sharpen
tools, the properties of
wood and of course learn-
ing how to draw and read
drawings.
The study of drawing is es-
sential to woodcarving. If
you don’t have the ability
to draw a certain design,
you will probably not be
able to carve it.
Sometimes the preparatory
drawings made by wood-
carvers are works of art in
their own right.
Drawing is 2 dimensional
and woodcarving is 3 di-
mensional. To help the ap-
prentice with the under-
standing of 3 dimensions,
modeling in clay was used
for practice.
A high level of self-discipline was required
as a carver could spend anything from 8 to
10 hours a day at his bench under instruc-
tion from the Master Carver.
When searching for inspiration for their designs, woodcarvers
often looked to nature. Oak and Agapanthus leaves were par-
ticularly popular for their beautiful shapes. Fruit and flowers
also make regular appearances.
What inspired the Christ Church Carv-
ers? See how many different plants,
fruit and flowers you can spot...
Agapanthus leaves
Oak leaves
Grapes
Chisels and
gouges are the
tools used by
woodcarvers. A
carver may have
up to 300 gouges.
Tools were made
in the workshop
on demand by
the carvers them-
selves. If a partic-
ular job needed a
certain tool to get
into a difficult
area then it was
specially made. To cut wood efficient-
ly the edge of the tool
needs to be razor
sharp. This is created
by using Sharpening
Stones. Different
grades of stone are
used throughout the
process, starting with
a heavy grit stone and
finishing with a fine
stone. A leather Strop
is then used to polish
the edge.
Contribution by woodcarver James McLoughlin
www.woodcarvingireland.ie
Stonework
This can be found all over the Cathedral — the walls themselves
are built of stone!
Around 1200 when work began on Christ Church, and during several stages of later development and repair - the main building
material was .... STONE. Concrete which is a modern material had not been invented - nor any other fancy modern materials.
All the better for Christ Church as natural stone is very beautiful and lasts a long time
“Written in stone” - is a saying that means that it will be there forever
some decorative work on the capitals / arches
carved pulpit made of Mansfield
stone
HOW HEAVY would this piece of stone
be ????
1 piece of Mansfield stone measuring 1 me-
ter x 1 meter x 1 meter would weigh about
2,250 kg - { 2 - 3 tonnes }
That is about the weight of 70 children
around the age of 10!
EVERY STONE IS DIFFERENT
All stone is old - VERY OLD - it was formed when the earth first came into existence. A person who stud-
ies stone is a Geologist
Stone masons and stone carvers learnt to tell what was good about some stone - they needed stone that
did not break off in big chunks as they needed to control what they did. They didn’t want big cracks !! So
not all stone is good for carving.
Each stone has a different colour. How many colour stones can you spot in the Cathedral ??
Kilkenny Marble
Grey limestone
Caen Stone
from Normandy
Carrera Marble
from Italy
Cork Marble Dundry
Stone
Portland Stone
When the Cathedral was being built there
were no trucks no cranes, and no engines of
any type - so ALL this stone got here by using
horses , carts , ropes ,and pulley systems.
Wow!
And all the more wow was that much of it
came from England and other parts of Europe
so had to go on a boat first - a very strong
boat that would not sink. with the weight of
the stone.
The craftsmen have put their own designs on the stone , but if you
look closely you may see designs within the stone , like fossils and
marble lines ....
Feel the stone around the church and write down things you notice about the tex-
ture ,the colour, patterns etc.
TEXTURE:
Colour:
Fossils and Patterns:
HOW DID THEY DO IT ??
Humans could only carve stone once they had learnt how to make metal chisels . So when the cathedral was built, wherever there were men { yes it was just men in those days ! } carving stone there were also blacksmiths. They made the chisels and sharpened them, as well as making the horseshoes for the horses who moved all the stone around.
A stone carver starts with a large chunk of stone and begins to take away the parts he does not want using a point chisel. By hitting this chisel with a lump hammer he shocks away a part of the stone. He does this again and again and again. The skill is in knowing where to take the stone away and when to stop!
The tooth chisel is then used to even out the bumpy surface he has just created and a flat chisel to give a smoother finish. Then the painstaking process of sanding begins . Special rough stones that are abrasive { scratchy }, sandpaper and metal files are all used to smooth the stone down.
o had to move all the stone around.
THE STONE TRAIL
The Cathedral is built of stone - which is amazing in itself. Just stand in the cathedral and think about the time, sweat and tears that all the men { yes men again } used to get those heavy blocks right up to the top.
Now have a look around the Cathedral and see if you can spot the following:
1 - Capitals in the North Transept - fancy decorative stone work at the top of the arches
featuring animals, flowers and people. Some of these are the original medieval capitals.
2 - Baptistery font - look at the beautiful stone ‘intarsia’ work { inlaying of different stones
into each other }. How many kinds of marble can you find?
3 - Monument to the 19th Earl of Kildare in the South Transept - sculpted by Henry
Cheere in 1746. It was said to be his best work, largely because of its incredible textures
and details {look for the fur and wrinkled stockings...}
4- Strongbow’s tomb - carved in Kilkenny limestone
5 - Funerary monuments down in the Crypt - can you find the rather grumpy looking Lord
Bowes? This monument was once 5 metres high and stood upstairs. It is made of Carra-
ra and Kilkenny marble. Lord Bowe’s portrait was said to look very like him and the
sculptor John van Nost was paid the huge sum of £500 for it in the late 1760s.
Contribution by stonecarver Sonia Caldwell
www.kilcoestudios.com
Men working as stone masons
often worked in a stone yard
and had very specific jobs.
Some did the decorative work,
some did the more complicated
figures and others just helped
with sanding and other jobs.
Many of these men would have
been apprentices - who learnt
by doing and watching.
Medieval Floor Tiles
These can be found in the Chapel of St Laud. Later reproductions can be
found all over the Cathedral - just look at your feet!
There are two types of tiles on the cathedral floor, the original 13th century
tiles and reproductions made in the 19th century. In 1562, when the roof of the Cathedral fell in,
lots of the medieval tiles were broken. Those that survived were re-laid in the chapel of St Laud. New ones
were made to replace them from the original designs. Can you tell the difference between the two?
Here is how the red and white medieval tiles were made….
Clay was dug from the ground – it was often found in fields or river banks. Different areas gave up different coloured clays. Once dug, the clay was transported either by wheelbar-row or cart and stored in the shade outside the potter’s work-shop for about a year, to weath-er. This made the clay easier to work.
The clay was wedged (kneaded, to remove the air). Sometimes sand was mixed into the clay. This helped to stop the tiles bending or warping as they dried. Once prepared, the soft clay was shaped into a ball and then thrown into a square wood-en frame or mould.
Extra clay was cut off with a thin wire. The tile was left to stiffen in the wooden mould until it was firm but not completely dry.
The moulds were probably laid on the ground to dry, as paw and hoof marks are sometimes found pressed into medieval tiles. Christ Church is said to have its very own 13th cen-tury bird claw-print! Can you find it?
When the tile was almost dry, a wooden stamp was pressed into the tile surface and sometimes patterns were cut out with a knife.
The inlaid marks were then filled with a liquid white clay, called slip. This was left to dry until it was as firm as the rest of the tile. The surface was then carefully scraped back to reveal the con-trasting white pattern in the red clay.
The inlaid marks were then filled with a liq-uid white clay, called slip. This was left to dry until it was as firm as the rest of the tile. The surface was then carefully scraped back to reveal the contrasting white pattern in the red clay.
The tiles were dried under cover in buildings with open sides for air to circulate and turned every day to ensure they dried evenly. As the clay dried, it shrank away from the wooden frame. The frames were then removed.
After about a week of drying, the tiles would be covered in a dusting of powdered lead and placed on shelves in a kiln. This glaze caused the white clay to appear yellowish when melted onto the tile surface.
Medieval tile kiln showing floor and wall thickness.
The kiln walls were made from large stones bound together with clay. Small spyholes were left in the walls to view inside the kiln during firing.
The kiln was heated with wood. This took several days. Once the glaze became shiny inside the red-hot kiln, all the fire boxes beneath the kiln would be closed up to stop cold air getting in and the kiln left to cool down slowly. After a few days, the kiln was opened and the tiles removed, ready to be laid as a floor.
Can you find all the
different animals de-picted in the tiles?
Here are just a few...lions, birds and
foxes dressed as fri-ars. You’ll only find
the foxes in Christ Church. (Medieval
people thought it was very funny to dress
animals as humans!) Contribution by glass and ceramic artist Michael Ray
www.glitteringglass.com
Books
A selection of old books from the Cathedral Archives can be found
down in the Crypt
Before the invention of PAPER, many ancient civilisations were using a rich variety of materi-
als on which to write: they engraved stone or metal, stamped clay surfaces or carved onto
bark stripped from trees to make their mark. They also stretched animal skin to make PARCH-
MENT. Many of Christ Church’s earliest books, including the famous Liber Niger (Black Book)
are written on parchment. Later books were written on handmade PAPER.
Parchment
Parchment is a general term for an animal skin which has been pre-
pared for writing or printing. Parchment has been made for centuries,
and is usually calf, goat, or sheep skin. VELLUM - from the French
`veau` - refers to a parchment made from calf skin.
Parchment was invented in Asia in around 1500BC and was widely used in
Europe until the sixteenth century. Although methods of PAPERMAK-
ING had reached parts of Europe by the 13th century, most medieval
manuscripts were still written on parchment.
PAPER – Where does it come from?
The Beginnings of Paper Making
The earliest records of PAPER are from China, 105AD. The Chinese had al-
ready been using felted off-cuts of silk as a painting surface. This practice led
to the use of plant leaves and bark to make strong, fibrous pulps.
Papermaking was
brought from China to
Japan in the 7th century
by Buddhist monks.
The use of linen rags
and flax fibre to make
paper was introduced to
the Arabian peninsula
by armies returning
from wars in Asia in the
8th – 9th century.
Over a thousand years after its invention, pa-
permaking finally reached Europe as the first
paper mills were established in Italy and
France. The very first was at Fabriano in Ita-
ly, which began in 1276.
` Did You Know?
WASPS can be also regarded as the first real papermak-
ers or nature`s papermakers: they chew on slivers of
wood and vegetation to `make` their own pulp for lining
their nest!
Paper` - Wasps Nest Installation (`NEST` Project), 2013 – by Tunde Toth
Handmade Paper – How do
we make it today?
Paper Making Processes
Western techniques of hand pa-
permaking vary greatly but most
methods use a mesh-covered mould
and deckle which are held together and
dipped into a vat / container filled with
pulp and water.
The `screen` shapes the wet
sheet of handmade paper.
The sheet is couched onto a
board, felt or cotton sheet,
gets pressed and is hung to
let it dry.
Papermaking at KOZO Studio, Co. Kilkenny
There are a great variety of materials that are suitable for pulps. Cotton,
bamboo, abaca and other plant fibres are available from specialist suppliers.
You can also use plants you collect yourself: daffodils, grasses, rushes and
nettles.
You can also make interesting, tex-
tured, recycled handmade papers from
(good quality) left over paper and pa-
per products.
Contribution by Visual Artist and
Papermaker Tunde Toth
www.kozostudio.wordpress.com
www.tundetoth.com