· web viewlinear floor drain consisting of a formed stainless steel channel body and grate...

SECTION 09 30 50TILE SETTING MATERIALS AND ACCESSORIES

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2007 - 2007 ARCAT, Inc. - All rights reserved

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Edge-protection and transition profiles for floors.

B. Finishing and edge-protection profiles for walls and countertops.

C. Wall access panel system.

D. Finishing and edge-protection profiles for stair nosings.

E. Movement joint and cove-shaped profiles.

F. Modular screed system.

G. Uncoupling membrane.

H. Waterproofing Membrane.

I. Floor drain, with integrated bonding flange.

J. Shower waterproofing: prefabricated substrates, waterproofing membrane, floor drain with integrated bonding flange, and sealant.

K. Drainage membranes.

L. Finishing and edge-protection profiles and gutters for balconies and terraces.

M. Setting materials: adhesives, mortars, grouts, and sealants.

N. Finishing and edge-protection profiles for resilient coverings.

1.2 RELATED SECTIONS

A. Section 03 30 00 - Cast-in-Place Concrete.

B. Section 05 55 00 - Metal Stair Treads and Nosings.

C. Section 06 10 00 - Rough Carpentry.

D. Section 07 90 00 - Joint Protection.

E. Section 09 29 00 - Gypsum Board.

09 30 50-1

F. Section 09 30 00 - Tiling.

G. Section 09307 - Tile Shower Components and Waterproofing Membrane. Shower trays, curbs, ramps, bench, niche, sealing compound, waterproofing membrane, drainage panels, drainage membrane compatible with floor drains.

H. Section 10 26 13 - Corner Guards.

I. Section 22 30 00 - Plumbing Equipment.

J. Section _____ - Radiant Heating Units: electric cables, electric mats, and hydronic piping.

1.3 REFERENCES

A. CSA B79-08: Floor, Area, and Shower Drains, and Cleanouts for Residential Construction.

B. IAPMO IGC 195: Interim Guide Criteria for Floor Drain with Integrated Bonding Flange.

C. Tile Council of North America (TCNA) Handbook for Ceramic Tile Installation.

D. Terrazzo, Tile and Marble Association of Canada (TTMAC) Specification Guide 09300 Tile Installation Manual.

E. American National Standard Specifications for the installation of ceramic tile A108 / A118 / A136.1.

1.4 SUBMITTALS

A. Submit under provisions of Section 01 30 00.

B. Product Data: Manufacturer's data sheets on each product to be used, including:1. Preparation instructions and recommendations.2. Storage and handling requirements and recommendations.3. Installation methods.

C. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) long, representing actual product, color, and finish.

D. Manufacturer's Certificates: Certify products meet or exceed specified requirements.

1.5 QUALITY ASSURANCE

A. Installer Qualifications: Company specializing in performing the work of this section with minimum five years experience.

B. Source Limitations for Setting Materials and Accessories: Obtain product of a uniform quality for each application condition from a single manufacturer.

C. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.1. Finish areas designated by Architect.2. Do not proceed with remaining work until workmanship, color, and sheen are

approved by Architect.3. Refinish mock-up area as required to produce acceptable work.

D. Preinstallation Conference: Conduct conference at the Project site.1. Convene one week prior to commencing work of this section.

09 30 50-2

2. Require attendance of installation material manufacturer, tile supplier, tile installer and installers of related work. Review installation procedures and coordination required with related work.

3. Meeting agenda includes but is not limited to:a. Surface preparation.b. Tile and installation material compatibility.c. Edge protection, transition and pre-fabricated movement joint profiles.d. Waterproofing techniques.e. Crack isolation techniques.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Store products in manufacturer's unopened packaging until ready for installation.

B. Protect materials from exposure to moisture. Do not deliver until after wet work is complete and dry.

C. Store materials in a dry, warm, ventilated weathertight location.

1.7 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

1.8 COORDINATION

A. Coordinate Work with other operations and installation of floor finish materials to avoid damage to installed materials.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: Schluter Systems, L.P., 194 Pleasant Ridge Road, Plattsburgh, NY 12901-5841. ASD. Tel: (800) 472-4588. Fax (800) 477-9783. E-mail:[email protected]. Web:www.schluter.com.

B. Acceptable Manufacturer: Schluter Systems (Canada) Inc., 21100 Chemin Ste-Marie, Ste-Anne-de-Bellevue, QC H9X 3Y8. Tel: (800) 667-8746. Fax (514) 336-2410. E-mail:[email protected]. Web:www.schluter.ca.

C. Substitutions: Not permitted.

D. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00.

2.2 EDGE-PROTECTION AND TRANSITION PROFILES FOR FLOORS

A. Schluter-SCHIENE1. Description: L-shaped profile with 1/8 inch (3.2 mm) wide visible surface integrated

trapezoid-perforated anchoring leg, and integrated grout joint spacer.2. Anchoring Leg:

a. Provide with straight anchoring leg.b. Provide with special radius anchoring leg for radius applications.

3. Material and Finish:a. EV4A - Stainless Steel Type 316 L = V4A.

09 30 50-3

1) Height as required to coordinate with tile selection and setting system selected.

b. E - Stainless Steel Type 304 = V2A.1) Height as required to coordinate with tile selection and setting system

selected.c. EB - Brushed Stainless Steel Type 304 = V2A.


d. M - Solid Brass.1) Height as required to coordinate with tile selection and setting system

selected.e. A - Aluminum.


f. AE - Satin Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.

B. Schluter-DECO1. Description: profile with 1/4 inch (6 mm) wide visible surface and integrated trapezoid-

perforated anchoring leg.2. Anchoring Leg:


3. Material and Finish:a. E - Stainless Steel Type 304 = V2A.


b. M - Solid Brass.1) Height as required to coordinate with tile selection and setting system

selected.c. MC - Chrome-plated Solid Brass.


d. AE - Satin Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.

C. Schluter-RENO-T1. Description: T-shaped profile with 1/16 inch (1 mm) thick beveled exposed surface

and 11/32 inch (9 mm) tall integrated vertical anchoring leg.2. Material and Finish:

a. E - Stainless Steel Type 304 = V2A.1) Width as required.

b. EB - Brushed Stainless Steel Type 304 = V2A.1) Width as required.

c. M - Solid Brass.1) Width as required.

d. AE - Satin Anodized Aluminum.1) Width as required.

e. AT - Satin Nickel Anodized Aluminum.1) Width as required.

f. AK - Satin Copper/Bronze Anodized Aluminum.1) Width as required.

g. AM - Satin Brass Anodized Aluminum.1) Width as required.

09 30 50-4

D. Schluter-RENO-TK1. Description: profile with sloped exposed surface, 1/4 inch (6 mm) deep channel below

exposed surface, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2. Anchoring Leg:a. Provide with straight anchoring leg.b. Provide with special radius anchoring leg for radius applications.



b. EB - Brushed Stainless Steel Type 304 = V2A.1) Height as required to coordinate with tile selection and setting system

selected.c. M - Solid Brass.


d. AE - Satin Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.e. ACB - Bright Chrome Anodized Aluminum.


f. AT - Satin Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.g. AK - Satin Copper/Bronze Anodized Aluminum.


h. ATGB - Brushed Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.i. AKGB - Brushed Copper/Bronze Anodized Aluminum.


j. ABGB - Brushed Antique Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.k. AMB - Bright Brass Anodized Aluminum.


E. Schluter-RENO-U1. Description: profile with sloped exposed surface, 5/32 inch (4 mm) tall leading edge,

integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.2. Material and Finish:

a. E - Stainless Steel Type 304 = V2A.1) Height as required to coordinate with tile selection and setting system

selected.b. EB - Brushed Stainless Steel Type 304 = V2A.


c. M - Solid Brass.1) Height as required to coordinate with tile selection and setting system

selected.d. AE - Satin Anodized Aluminum.

09 30 50-5


e. ACB - Bright Chrome Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.f. AT - Satin Nickel Anodized Aluminum.


g. AK - Satin Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.h. ATGB - Brushed Nickel Anodized Aluminum.


i. ABGB - Brushed Antique Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.j. AKGB - Brushed Copper/Bronze Anodized Aluminum.


k. AM - Satin Brass Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.l. AMB - Bright Brass Anodized Aluminum.


F. Schluter-RENO-RAMP-K1. Description: anodized aluminum profile with textured, sloped exposed surface,

tapered leading edge and integrated grout joint spacer.2. Material and Finish:

a. AE - Satin Anodized Aluminum.3. Height: 1/2 inch (12.5 mm).4. Ramp Length: 2-1/2 inch (64 mm)

G. Schluter-RENO-RAMP1. Description: anodized aluminum profile with textured, sloped exposed surface,

tapered leading edge, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2. Material and Finish:a. AE - Satin Anodized Aluminum.

3. Height:a. 3/8 inch (10 mm).b. 1/2 inch (12.5 mm).c. 9/16 inch (15 mm).d. 3/4 inch (20 mm).e. Height as required.

4. Ramp Length:a. 2-1/2 inch (64 mm) Only available in 3/8 inch (10 mm) and 1/2 inch (12.5 mm)

heights.b. 3-1/2 in (89 mm). Only available in 1/2 inch (12.5 mm), 9/16 inch (15 mm) and

3/4 inch (20 mm) heights.c. Length as required.

H. Schluter-RENO-V1. Description: ball-and-socket hinged profile with sloped exposed surface, tapered

09 30 50-6

leading edge, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.



b. AM - Satin Brass Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.3. Ramp Length:

a. 3/4 inch (20 mm).b. 1-3/16 in (30 mm).c. 1-9/16 in (40 mm).d. Length as required.

2.3 FINISHING AND EDGE-PROTECTION PROFILES FOR WALLS AND COUNTERTOPS

A. Schluter-JOLLY1. Description: L-shaped profile with 1/8 inch (3.2 mm) wide top section vertical wall

section that together form the visible surface, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2. Anchoring Leg:a. Provide with straight anchoring leg.b. Provide with special radius anchoring leg for radius applications.

3. Material and Finish:a. MC - Chrome-plated Solid Brass.


b. ACG - Polished Chrome Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.c. ACGB - Brushed Chrome Anodized Aluminum.


d. AT - Satin Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.e. ATG - Polished Nickel Anodized Aluminum.


f. ATGB - Brushed Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.g. AK - Satin Copper/Bronze Anodized Aluminum.


h. AKG - Polished Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.i. AKGB - Brushed Copper/Bronze Anodized Aluminum.


j. ABGB - Brushed Antique Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.k. AM - Satin Brass Anodized Aluminum.

09 30 50-7


l. AMG - Polished Brass Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.m. AMGB - Brushed Brass Anodized Aluminum.


n. AGRB - Brushed Graphite Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.o. AGSG - Bright Black Anodized Aluminum.


p. AC - Color-coated Aluminum.1) BW - Bright White.

a) Height as required to coordinate with tile selection and setting system selected.

2) W - White.a) Height as required to coordinate with tile selection and setting

system selected.3) SP - Sand Pebble.


4) BH - Bahama.a) Height as required to coordinate with tile selection and setting

system selected.5) HB - Light Beige.


6) HG - Light Grey.a) Height as required to coordinate with tile selection and setting

system selected.7) PG - Classic Grey.


8) G - Grey.a) Height as required to coordinate with tile selection and setting

system selected.9) RB - Red Brown.


10) SB - Black Brown.a) Height as required to coordinate with tile selection and setting

system selected.11) GM- Metallic Grey.


12) TSR - Rustic Brown.a) Height as required to coordinate with tile selection and setting

system selected.13) TSDA - Dark Anthracite.


14) TSLA - Light Anthracite.a) Height as required to coordinate with tile selection and setting

09 30 50-8

system selected.15) TSSG - Stone Grey.


16) TSC - Cream.a) Height as required to coordinate with tile selection and setting

system selected.17) TSBG - Greige.


18) TSI - Ivory.a) Height as required to coordinate with tile selection and setting

system selected.19) TSB - Beige.


20) TSOB - Bronze.a) Height as required to coordinate with tile selection and setting

system selected.21) TSG - Pewter.


22) MGS - Matte Black.a) Height as required to coordinate with tile selection and setting

system selected.23) MBW - Matte White.


q. P - PVC.1) BW - Bright White.












system selected.9) GS - Black.


09 30 50-9

B. Schluter-SCHIENE1. Description: L-shaped profile with 1/8 inch (3.2) wide visible surface, integrated

trapezoid-perforated anchoring leg, and integrated grout joint spacer.2. Anchoring Leg:







d. M - Solid Brass.1) Height as required to coordinate with tile selection and setting system

selected.e. A - Aluminum.



selected.

C. Schluter-QUADEC1. Description: profile with square visible surface, integrated trapezoid-perforated

anchoring leg, and integrated grout joint spacer.2. Corners:

a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with internal connectors.




selected.c. ES1 - Stainless Steel Type 304 = V2A with Square Check Pattern.


d. ES2 - Brushed Stainless Steel Type 304 = V2A with Leather Textured Pattern.1) Height as required to coordinate with tile selection and setting system

selected.e. AE - Satin Anodized Aluminum.


f. ACG - Polished Chrome Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.g. AT - Satin Nickel Anodized Aluminum.


h. ABGB - Brushed Antique Bronze Anodized Aluminum.

09 30 50-10


i. AC - Color-coated Aluminum:1) BW - Bright White.





4) PG - Classic Grey.a) Height as required to coordinate with tile selection and setting

system selected.5) SB - Black Brown.


6) QG- Quartz Grey.a) Height as required to coordinate with tile selection and setting

system selected.7) VG- Traffic Grey.


8) TSR - Rustic Brown.a) Height as required to coordinate with tile selection and setting

system selected.9) TSDA - Dark Anthracite.


10) TSLA - Light Anthracite.a) Height as required to coordinate with tile selection and setting

system selected.11) TSSG - Stone Grey.


12) TSC - Cream.a) Height as required to coordinate with tile selection and setting

system selected.13) TSBG - Greige.


14) TSI - Ivory.a) Height as required to coordinate with tile selection and setting

system selected.15) TSB - Beige.


16) TSOB - Bronze.a) Height as required to coordinate with tile selection and setting

system selected.17) TSG - Pewter.


18) MGS - Matte Black.a) Height as required to coordinate with tile selection and setting

09 30 50-11

system selected.19) MBW - Matte White.


j. P - PVC.1) BW - Bright White.


2) White.a) Height as required to coordinate with tile selection and setting










system selected.9) GS - Black.


D. Schluter-DIADEC1. Description: Anodized aluminum profile with a 45 Degree beveled reveal for outside

corners of tiled walls, integrated trapezoid-perforated anchoring leg.2. Corners:

a. Provide with matching outside corners.3. Material and Finish:

a. AE - Satin Anodized Aluminum.b. ACG - Polished Chrome Anodized Aluminum.c. ACGB - Brushed Chrome Anodized Aluminum.

4. Profile Height:a. Height as required to coordinate with tile selection and setting system selected.

E. Schluter-DIADEC - K1. Description: Anodized aluminum profile with a 45 Degree beveled reveal for outside

corners of tiled walls, without anchoring leg.2. Corners:


a. AE - Satin Anodized Aluminum.b. ACG - Polished Chrome Anodized Aluminum.


09 30 50-12

F. Schluter-INDEC1. Description: Anodized aluminum profile with a square recessed reveal for outside

corners of tiled walls, integrated trapezoid-perforated anchoring leg.2. Corners:


a. AE - Satin Anodized Aluminum.b. ACG - Polished Chrome Anodized Aluminum.


G. Schluter-FINEC1. Description: Profile with a 1/8 inch (3.5 mm) reveal for outside corners of tiled walls,

and 135 Degree integrated trapezoid-perforated anchoring leg.2. Corners:

a. Provide with matching outside corners3. Material and Finish:

a. E - Stainless Steel Type 304 = V2Ab. AE - Satin Anodized Aluminumc. AC - Color-coated Aluminum:

1) TSR Rustic Brown color-coated Aluminum2) TSDA - Dark Anthracite color-coated Aluminum3) TSLA - Light Anthracite color-coated Aluminum4) TSSG - Stone Grey color-coated Aluminum5) TSC - Cream color-coated Aluminum6) TSBG - Greige color-coated Aluminum7) TSI - Ivory color-coated Aluminum8) TSB - Beige color-coated Aluminum9) TSOB - Bronze color-coated Aluminum10) TSG - Pewter color-coated Aluminum11) MSG - Matte Black color-coated Aluminum12) MBW - Matte White color-coated Aluminum


H. Schluter-DECO-DE1. Description: roll-formed stainless steel finishing and edge-protection profile with a 135

degree reveal for outside corners of tiled walls. Profile features an integrated trapezoid perforated anchoring leg.

2. Material and Finish:a. E - Stainless Steel 304b. EB - Brushed Stainless Steel 304.

3. Profile Height:a. Height as required to coordinate with tile selection and tile setting system

selected.

I. Schluter-DECO-SG1. Description: Prefabricated channel reveal profile with 1/8 inch (3 mm) wide vertical

side sections and channel that together form the exposed shadow gap reveal, integrated trapezoid perforated anchoring leg.




09 30 50-13

selected.c. E - Stainless Steel 304.


3. Reveal Width:a. 1/2 inch (12.5 mm).b. 9/16 inch (15 mm).

J. Schluter-QUADEC-FS1. Description: anodized aluminum, double-rail profile with 3/8 inch (10mm) -wide,

square exposed surfaces separated by a 2 inch (51 mm) -wide recessed section with dovetail channel.

2. Corners:a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with end caps for exposed edges.


1) 5/16 inch (8 mm).b. ACG - Polished Chrome Anodized Aluminum.

1) 5/16 inch (8 mm).c. AT - Satin Nickel Anodized Aluminum.

1) 5/16 inch (8 mm).d. ABGB - Brushed Antique Bronze Anodized Aluminum.

1) 5/16 inch (8 mm).

K. Schluter-RONDEC1. Description: bullnose-type profile with symmetrically rounded visible surface with 1/4

inch (6 mm) radius, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2. Corners:a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with matching internal connectors.






d. MC - Chrome-plated Solid Brass.1) Height as required to coordinate with tile selection and setting system

selected.e. AE - Satin Anodized Aluminum.


f. ACG - Polished Chrome Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.g. ACGB - Brushed Chrome Anodized Aluminum.


09 30 50-14

h. AT - Satin Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.i. ATG - Polished Nickel Anodized Aluminum.


j. AGB - Brushed Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.k. AK - Satin Copper/Bronze Anodized Aluminum.


l. AKG - Polished Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.m. AKGB - Brushed Copper/Bronze Anodized Aluminum.


n. AM - Satin Brass Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.o. AMG - Polished Brass Anodized Aluminum.


p. AMGB - Brushed Brass Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.q. AGR - Graphite Anodized Aluminum.


r. AGSG - Bright Black Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.s. AGSB - Brushed Black Anodized Aluminum.


t. AC - Color-coated Aluminum.1) BW - Bright White.










09 30 50-15



system selected.9) TSR - Rustic Brown Color-coated Aluminum.


10) TSDA - Dark Anthracite Color-coated Aluminum.a) Height as required to coordinate with tile selection and setting

system selected.11) TSLA - Light Anthracite Color-coated Aluminum.


12) TSSG - Stone Grey Color-coated Aluminum.a) Height as required to coordinate with tile selection and setting

system selected.13) TSC - Cream Color-coated Aluminum.


14) TSBG - Greige Color-coated Aluminum.a) Height as required to coordinate with tile selection and setting

system selected.15) TSI - Ivory Color-coated Aluminum.


16) TSB - Beige Color-coated Aluminum.a) Height as required to coordinate with tile selection and setting

system selected.17) TSOB - Bronze Color-coated Aluminum.


18) TSG - Pewter Color-coated Aluminum.a) Height as required to coordinate with tile selection and setting

system selected.19) MGS - Matte Black Color-coated Aluminum.


20) GM - Metallic Grey.a) Height as required to coordinate with tile selection and setting

system selected.21) SB - Black Brown.


22) MBW - Matte White Color-coated Aluminum.a) Height as required to coordinate with tile selection and setting

system selected.u. PRO - PVC. Color

1) BW - Bright White.a) Height as required to coordinate with tile selection and setting

system selected.2) W - White.


3) SP - Sand Pebble.a) Height as required to coordinate with tile selection and setting

09 30 50-16

system selected.4) BH - Bahama.


5) HB - Light Beige.a) Height as required to coordinate with tile selection and setting

system selected.6) HG - Light Grey.


7) PG - Classic Grey.a) Height as required to coordinate with tile selection and setting

system selected.8) G - Grey.


9) GS - Black.a) Height as required to coordinate with tile selection and setting

system selected.

L. Schluter-ECK-E1. Description: roll-formed stainless steel V-shaped profile with 1-15/32 inch (37 mm)

wide exposed surfaces joined by a symmetrically rounded corner, with integrated trapezoid-perforated anchoring legs.

2. Profile Angle:a. Profile with 90 degree angle.b. Profile with 135 degree angle.



b. EV4A - Stainless Steel Type 316 L = V4A.1) Height as required to coordinate with tile selection and setting system



M. Schluter-ECK-K1. Description: roll-formed stainless steel V-shaped profile with 1-9/32 inch (32 mm) or 2

inch (50 mm) wide beveled exposed surfaces joined by a symmetrically rounded corner.

2. Profile Angle:a. Profile with 90 degree angle.b. Profile with 135 degree angle.


1) 9/16 inch (15 mm).2) 1-9/32 inch (32 mm).3) 2 inch (50 mm).4) Width as required.

b. EV4A - Stainless Steel Type 316 L = V4A.1) 9/16 inch (15 mm).2) 1-9/32 inch (32 mm).3) 2 inch (50 mm).4) Width as required.

09 30 50-17

c. EB - Brushed Stainless Steel Type 304 = V2A.1) 9/16 inch (15 mm).2) 1-9/32 inch (32 mm).3) 2 inch (50 mm).4) Width as required.

N. Schluter-ECK-KI1. Description: Stainless steel inside wall corner profile with 9/16 inch (15 mm) wide

exposed surfaces joined by a symmetrically rounded inside corner with 3/64 inch (1 mm) radius.

2. Corners and Connectors:a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with matching connectors.

3. Material and Finish:a. E - Stainless Steel Type 304 = V2A.b. EV4A - Stainless Steel Type 316 L = V4A.c. EB - Brushed Stainless Steel Type 304 = V2A.

O. Schluter-ECK-KHK1. Description: Stainless steel inside wall corner profile with 9/16 inch (15 mm) wide

exposed surfaces joined by a symmetrically rounded inside corner with 5/16 inch (8 mm) radius.



P. Schluter-RONDEC-DB1. Description: profile with symmetrically rounded 3/8 inch (10 mm) wide, 17/32 inch (14

mm) tall exposed surface, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2. Corners:a. Provide with matching outside corners.



b. AK - Satin Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.c. AM - Satin Brass Anodized Aluminum.


Q. Schluter-DESIGNLINE1. Description: U-shaped profile with 1 inch (25 mm) wide exposed surface and 1/4 inch

(6 mm) tall integrated vertical anchoring legs on each side.2. Material and Finish:


selected.

09 30 50-18


selected.c. ES1 - Stainless Steel Type 304 = V2A with Square Check Pattern.


d. ES2 - Brushed Stainless Steel Type 304 = V2A with Leather Textured Pattern.1) Height as required to coordinate with tile selection and setting system

selected.e. MC - Chrome-plated Solid Brass.



selected.g. ACG - Polished Chrome Anodized Aluminum.


h. ACGB - Brushed Chrome Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.i. AT - Satin Nickel Anodized Aluminum.


j. ATG - Polished Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.k. ATGB - Brushed Nickel Anodized Aluminum.


l. AK - Satin Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.m. AKG - Polished Copper/Bronze Anodized Aluminum.


n. AKGB - Brushed Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.o. AM - Satin Brass Anodized Aluminum.


p. AMG - Bright Brass Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.q. AMGB - Brushed Brass Anodized Aluminum.


R. Schluter-DESIGNBASE - SL1. Description: Prefabricated Baseboard profile comprised of a symmetrically-rounded

top, flat exposed face, and 5/16 inch (8 mm) radius lower section.2. Corners:

a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with matching connectors.

09 30 50-19

d. Provide with matching end caps.e. Provide with matching Sealing Lip.


1) Height:a) 2-3/8 inch (60 mm).b) 3-1/8 inch (80 mm).c) Height as required.

b. AEEB - Anodized Aluminum with Brushed Stainless Steel appearance.1) Height:

a) 2-3/8 inch (60 mm).b) 3-1/8 inch (80 mm).c) Height as required.

c. MBW - Matte White Color-Coated Aluminum.1) Height:

a) 2-3/8 inch (60 mm).b) 3-1/8 inch (80 mm).c) Height as required.

S. Schluter-RONDEC-CT1. Description: anodized aluminum, double-rail profile with symmetrically-rounded

exposed surfaces with 1/4 inch (6 mm) radii separated by a 1-1/4 inch (31 mm) wide recessed section with dovetail channels, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2. Corners:a. Provide with matching inside corners.b. Provide with matching outside corners.



b. ACGB - Brushed Chrome Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.c. AT - Satin Nickel Anodized Aluminum.


d. ATGB - Brushed Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.e. AK - Satin Copper/Bronze Anodized Aluminum.


f. AKGB - Brushed Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.g. AM - Satin Brass Anodized Aluminum.


h. AMGB - Brushed Brass Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.i. TSB - Beige Color-coated Aluminum.


j. TSOB - Bronze Color-coated Aluminum.

09 30 50-20


k. TSG - Pewter Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.

T. Schluter-RONDEC-STEP1. Description: anodized aluminum profile with flat exposed face, symmetrically-rounded

exposed top surface with 1/4 inch (6 mm) radius, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2. Corners:a. Provide with matching inside corners.b. Provide with matching outside corners.



2) Length:a) 1-3/8 inch (35 mm).b) 1-1/2 inch (39 mm).c) 2-1/4 inch (57 mm).d) Length as required.


selected.2) Length:

a) 1-3/8 inch (35 mm).b) 1-1/2 inch (39 mm).c) 2-1/4 inch (57 mm).d) Length as required.

c. AT - Satin Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.2) Length:



selected.2) Length:

a) 1-3/8 inch (35 mm).b) 1-1/2 inch (39 mm).c) Length as required.

e. AK - Satin Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.2) Length:



selected.

09 30 50-21

2) Length:a) 1-3/8 inch (35 mm).b) 1-1/2 inch (39 mm).c) 2-1/4 inch (57 mm).d) Length as required.

g. AM - Satin Brass Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.2) Length:



selected.2) Length:



selected.2) Length:

a) 1-1/2 inch (39 mm).b) Length as required.

U. Schluter-REMA1. Description: wall access panel system featuring aluminum brackets with molded

casings containing magnets that are clamped to lateral, movable guide shoes, and ferromagnetic metal counterplates.

2.4 FINISHING AND EDGE-PROTECTION PROFILES FOR STAIR NOSINGS

A. Schluter-TREP-E1. Description: roll-formed stainless steel (type 304 = V2A) profile with ribbed, 1-3/16

inch (30 mm) wide exposed surface with rounded leading edge, and integrated trapezoid-perforated anchoring leg.

2. End Caps: Provide with matching end caps.3. Material and Finish:

a. EV4A - Stainless Steel Type 316 L = V4A.1) Height as required to coordinate with tile selection and setting system

selected.b. E - Stainless Steel Type 304 = V2A.


B. Schluter-TREP-EK1. Description: roll-formed stainless steel (type 304 = V2A) profile with ribbed, 1-3/16

inch (30 mm) wide exposed surface with rounded leading edge.

C. Schluter-TREP-EFK1. Description: roll-formed stainless steel (type 304 = V2A) profile with ribbed, 2-7/32

inch (56.5 mm) wide exposed surface.

D. Schluter-TREP-G-S1. Description: roll-formed brushed stainless steel (type 304 = V2A) profile with self-

09 30 50-22

adhesive, non-slip tread, 1-3/16 inch (30 mm) wide exposed surface with rounded leading edge, and integrated trapezoid-perforated anchoring leg.

2. End Caps: Provide with matching end caps.3. Tread Color:

a. T - Transparent.1) Height as required to coordinate with tile selection and setting system

selected.b. NB - Nut Brown.


c. GS - Black.1) Height as required to coordinate with tile selection and setting system

selected.d. CG - Yellow.


E. Schluter-TREP-G-B1. Description: roll-formed brushed stainless steel (type 304 = V2A) profile with self-

adhesive, non-slip tread, 2-5/32 (55 mm) wide exposed surface with rounded leading edge, and integrated trapezoid-perforated anchoring leg.


a. T - Transparent.1) Height as required to coordinate with tile selection and setting system




selected.d. CG - Yellow.


F. Schluter-TREP-GK-S1. Description: roll-formed brushed stainless steel (type 304 = V2A) profile with self-

adhesive, non-slip tread, 1-3/16 inch (30 mm) wide exposed surface with rounded leading edge.

2. Tread Color:a. T - Transparent.b. GS - Black.

G. Schluter-TREP-GK-B1. Description: roll-formed brushed stainless steel (type 304 = V2A) profile with self-

adhesive, non-slip tread, 1-3/16 inch (30 mm) wide exposed surface with rounded leading edge.

2. Tread Color:a. T - Transparent.b. GS - Black.

H. Schluter-TREP-SE1. Description: Profile with replaceable, ribbed, 1-1/32 inch (26 mm) wide, thermoplastic

rubber exposed surface with rounded leading edge, and roll-formed stainless steel type 304 = V2A support section with integrated trapezoid-perforated anchoring leg.

09 30 50-23


a. HB - Light Beige.1) Height as required to coordinate with tile selection and setting system




selected.d. G - Grey.


e. CG - Yellow.1) Height as required to coordinate with tile selection and setting system

selected.

I. Schluter-TREP-S1. Description: Profile with replaceable, ribbed, 1-1/32 inch (26 mm) wide, thermoplastic

rubber exposed surface with rounded leading edge, and aluminum support section with integrated trapezoid-perforated anchoring leg.









selected.

J. Schluter-TREP-B1. Description: Profile with replaceable, ribbed, 2-1/16 inch (52 mm) wide, thermoplastic

rubber exposed surface with rounded leading edge, and aluminum support section with integrated trapezoid-perforated anchoring leg.







09 30 50-24



selected.

K. Schluter-TREP-FL1. Description: roll-formed stainless steel (type 304 = V2A) profile, with 11/32 inch (9

mm) -wide, 13/16 inch (21 mm) -tall, exposed surface with rounded leading edge, and integrated trapezoid-perforated anchoring leg.

2. End Caps: Provide with matching end caps.3. Material and Finish:


selected.b. EB - Brushed Stainless Steel Type 304 = V2A.


L. Schluter-SCHIENE-STEP1. Description: T-Shaped profile with 1/8 inch (3 mm) wide top section and vertical leg

that together for the exposed surface, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2. Corners:a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with Matching End Caps.



2) Vertical Length:a) 1-3/16 inch (30 mm).b) 1-1/2 inch (39 mm).c) Length as required.

b. AT - Brushed Chrome Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.2) Vertical Length:


c. EB - Brushed Stainless Steel.1) Height as required to coordinate with tile selection and setting system


a) 7/16 inch (11 mm).b) 1-3/16 inch (30 mm).c) 1-1/2 inch (39 mm).d) Length as required.

M. Schluter-RONDEC-STEP1. Description: anodized aluminum profile with flat exposed face, symmetrically-rounded

exposed top surface with 1/4 inch (6 mm) radius, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2. Corners:

09 30 50-25

a. Provide with matching inside corners.b. Provide with matching outside corners.



2) Vertical Length:a) 1-3/8 inch (35 mm).b) 1-1/2 inch (39 mm).c) 2-1/4 inch (57 mm).d) Length as required.




c. AT - Satin Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system






e. AK - Satin Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system






g. AM - Satin Brass Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system



09 30 50-26






a) 1-1/2 inch (39 mm).b) Length as required.

2.5 MOVEMENT JOINTS AND COVE-SHAPED PROFILES

A. Schluter-DILEX-BWS1. Description: profile with integrated rigid, recycled PVC, trapezoid-perforated anchoring

legs, connected by a 3/16 inch (5 mm) wide soft CPE movement zone that forms the visible surface.

2. Movement Zone Color:a. BW - Bright White.


b. SP - Sand Pebble.1) Height as required to coordinate with tile selection and setting system

selected.c. HB - Light Beige.


d. GS - Black.1) Height as required to coordinate with tile selection and setting system

selected.e. PG - Classic Grey.


f. G - Grey.1) Height as required to coordinate with tile selection and setting system

selected.

B. Schluter-DILEX-BWB1. Description: profile with integrated rigid, recycled PVC, trapezoid-perforated anchoring

legs, connected by a 3/8 inch (10 mm) wide soft CPE movement zone that forms the visible surface.






d. GS - Black.

09 30 50-27


e. PG - Classic Grey.1) Height as required to coordinate with tile selection and setting system

selected.f. G - Grey.


C. Schluter-DILEX-AKWS1. Description: profile with integrated aluminum, trapezoid-perforated anchoring legs,

connected by grip bars to a 1/4 inch (6 mm) wide soft PVC movement zone, which together form the visible surface.

2. Movement Zone Color:a. SP - Sand Pebble.


b. HB - Light Beige.1) Height as required to coordinate with tile selection and setting system

selected.c. GS - Black.


d. PG - Classic Grey.1) Height as required to coordinate with tile selection and setting system

selected.e. G - Grey.


D. Schluter-DILEX-EDP1. Description: stainless steel profile with integrated trapezoid-perforated anchoring legs

connected by a 15/32 inch (12 mm) wide tongue-and-groove joint that forms the visible surface.



E. Schluter-DILEX-KSN1. Description: profile with integrated trapezoid-perforated anchoring legs, connected by

a 7/16 inch (11 mm) wide replaceable thermoplastic rubber movement zone, which together form the visible surface.

2. Anchoring Legs Material:a. E - Stainless Steel Type 304 = V2A.



selected.c. A - Aluminum.


3. Movement Zone Color:a. SP - Sand Pebble.b. HB - Light Beige.

09 30 50-28

c. GS - Black.d. PG - Classic Grey.e. G - Grey.

F. Schluter-DILEX-EKSB1. Description: profile with integrated roll-formed stainless steel with trapezoid-perforated

anchoring legs, connected by a 1/4 inch (6 mm) wide thermoplastic rubber movement zone, which together form the visible surface.




selected.3. Movement Zone Color:

a. HB - Light Beige.b. GS - Black.c. PG - Classic Grey.d. G - Grey.

G. Schluter-DILEX-EZ1. Description: Profile with textured, concave, rigid PVC side walls connected on top

and bottom by 9/32 inch (7 mm) wide soft PVC movement zones that form the visible surface.

2. Movement Color:a. M/G - Brass Inlay/Grey.


b. C/CG - Chrome Inlay/Yellow.1) Height as required to coordinate with tile selection and setting system

selected.

H. Schluter-DILEX-BT1. Description: Extruded satin anodized aluminum profile with integrated trapezoid-

perforated anchoring legs, connected by a 1-3/16 inch (30 mm) wide sliding telescopic center section with two interconnected ball-and-socket joints, which together form the visible surface.

2. Profile Heighta. Height as required to coordinate with tile selection and setting system selected.

I. Schluter-DILEX-BT/O1. Description: Extruded satin anodized aluminum profile with integrated trapezoid-

perforated anchoring legs, connected at a 90-degree angle by a 1-3/16 inch (30 mm) wide sliding telescopic center section with two interconnected ball-and-socket joints, which together form the visible surface.


J. Schluter-DILEX-BTS1. Description: Extruded satin anodized aluminum profile with 3/8 inch (10 mm) tall

integrated anchoring legs, connected by a 1-3/16 inch (30 mm) wide sliding telescopic center section with two interconnected ball-and-socket joints, which together form the visible surface.

K. Schluter-DILEX-MOP1. Description: profile with serrated rigid, recycled PVC side sections connected by a soft

09 30 50-29

PVC central movement zone, which form the 5/16 inch (8 mm) wide visible surface.2. Size:

a. Height as required to coordinate with tile selection and setting system selected.

L. Schluter-DILEX-MP1. Description: profile with dovetailed, rigid, recycled PVC side sections overlapped and

connected by a 5/16 inch (8 mm) wide soft CPE central movement zone that forms the visible surface.

2. Color:a. HB - Light Beige.

1) 1-3/8 inch (35 mm).b. ZR - Brick Red.

1) 1-3/8 inch (35 mm).c. GS - Black.

1) 1-3/8 inch (35 mm).d. G - Grey.

1) 1-3/8 inch (35 mm).3. Size: Height as required.

M. Schluter-DILEX-MPV1. Description: profile extension for Schluter-DILEX-MP with rigid, recycled PVC side

sections and interlocking top and bottom cross-sections.2. Size:

a. Height: 9/16 inch (15 mm).b. Height: 1 inch (25 mm).c. Height as required.

N. Schluter-DILEX-AS1. Description: profile with integrated rigid PVC trapezoid-perforated anchoring leg and a

sloped flexible joining leg, with self-adhesive tape on the underside, which forms the visible surface.

2. Corners:a. Provide with matching inside corners.b. Provide with matching end caps.

3. Color:a. BW - Bright White.

1) 3/8 inch (10 mm).

O. Schluter-DILEX-BWA1. Description: profile with integrated rigid, recycled PVC trapezoid-perforated anchoring

leg and dovetailed channel, which are connected by a 3/16 inch (5 mm) wide soft CPE movement zone that forms the visible surface, and a slit lower movement zone of soft CPE.

2. Color:a. BW - Bright White.



selected.c. SP - Sand Pebble.



selected.

09 30 50-30

e. PG - Classic Grey.1) Height as required to coordinate with tile selection and setting system

selected.f. G - Grey.


P. Schluter-DILEX-KSA1. Description: profile with integrated trapezoid-perforated anchoring leg and 3/8 inch (10

mm) wide replaceable thermoplastic rubber movement zone with self-adhesive backing strip, which together form the visible surface.




selected.c. A - Aluminum.


3. Movement Color:a. HB - Light Beige.b. GS - Black.c. G - Grey.d. PG - Light Grey.

Q. Schluter-DILEX-EKE1. Description: profile with integrated rigid, recycled PVC trapezoid-perforated anchoring

legs, connected at a 90-degree angle by a 3/16 inch (5 mm) wide soft CPE movement zone that forms the visible surface.







selected.e. PG - Classic Grey.


f. G - Grey.1) Height as required to coordinate with tile selection and setting system

selected.

R. Schluter-DILEX-HKW1. Description: profile with rigid, recycled PVC integrated trapezoid-perforated anchoring

legs, connected at a 90-degree angle by a rigid PVC cove-shaped section with 11/16 inch (18 mm) radius that forms the visible surface.

2. Corners:

09 30 50-31

a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with matching end caps.d. Provide with matching connectors.

3. Cove Section Color:a. BW - Bright White.



selected.c. PG - Classic Grey.


d. G - Grey.1) Height as required to coordinate with tile selection and setting system

selected.

S. Schluter-DILEX-HK1. Description: profile with integrated rigid, recycled PVC trapezoid-perforated anchoring

legs, connected at a 90-degree angle by a soft CPE cove-shaped section with 11/16 inch (18 mm) radius that forms the visible surface.

2. Corners:a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with matching end caps.d. Provide with matching connectors.

3. Cove Section Color:a. BW - Bright White.



selected.c. G - Grey.


T. Schluter-DILEX-AHK1. Description: anodized aluminum profile with integrated trapezoid-perforated anchoring

legs, connected at a 90-degree angle by a cove-shaped section with 3/8 inch (10 mm) radius that forms the visible surface.





selected.c. ACGB - Brushed Chrome Anodized Aluminum.

1) Height as required to coordinate with tile selection and setting system

09 30 50-32

selected.d. AT - Satin Nickel Anodized Aluminum.


e. ATG - Polished Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.f. ATGB - Polished Brushed Nickel Anodized Aluminum.


g. AK - Satin Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.h. AKG - Polished Copper/Bronze Anodized Aluminum.


i. AKGB - Brushed Copper/Bronze Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.j. AM - Satin Brass Anodized Aluminum.


k. AMG - Polished Brass Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.l. AMGB - Brushed Brass Anodized Aluminum.


m. AGRB - Brushed Graphite Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.n. TSR - Rustic Brown Color-coated Aluminum.


o. TSDA - Dark Anthracite Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.p. TSLA - Light Anthracite Color-coated Aluminum.


q. TSSG - Stone Grey Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.r. TSC - Cream Color-coated Aluminum.


s. TSBG - Greige Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.t. TSI - Ivory Color-coated Aluminum.


u. TSB - Beige Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.v. TSOB - Bronze Color-coated Aluminum.

09 30 50-33


w. TSG - Pewter Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.

U. Schluter-DILEX-PHK1. Description: Pre-colored rigid PVC profile with integrated trapezoid-perforated

anchoring legs, connected at a 90-degree angle by a cove-shaped section with 3/8 inch (10 mm) radius that forms the visible surface.


3. Finish and Height:a. BW - Bright White.


b. W - White.1) Height as required to coordinate with tile selection and setting system

selected.c. SP - Sand Pebble.


d. BH - Bahama.1) Height as required to coordinate with tile selection and setting system

selected.e. HB - Light Beige.


f. PG - Classic Grey.1) Height as required to coordinate with tile selection and setting system

selected.g. G - Grey.


V. Schluter-DILEX-AHKA1. Description: Anodized aluminum profile with single integrated trapezoid-perforated

anchoring leg and dovetailed channel, connected at a 90 degree angle by a cove-shaped 3/8 inch (10 mm) radius section that forms the visible surface.

2. Corners:a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with matching end caps.




selected.c. AT - Satin Nickel Anodized Aluminum.


09 30 50-34

d. ATGB - Polished Brushed Nickel Anodized Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.e. TSR - Rustic Brown Color-coated Aluminum.


f. TSDA - Dark Anthracite Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.g. TSLA - Light Anthracite Color-coated Aluminum.


h. TSSG - Stone Grey Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.i. TSC - Cream Color-coated Aluminum.


j. TSBG - Greige Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.k. TSI - Ivory Color-coated Aluminum.


l. TSB - Beige Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.m. TSOB - Bronze Color-coated Aluminum.


n. TSG - Pewter Color-coated Aluminum.1) Height as required to coordinate with tile selection and setting system

selected.

W. Schluter-DILEX-EHK1. Description: roll-formed stainless steel profile with integrated trapezoid-perforated

anchoring legs, connected at a 90-degree angle by a cove-shaped section with 23/32 inch (18.5 mm) radius that forms the visible surface.







X. Schluter-DILEX-HKU1. Description: roll-formed stainless steel cove-shaped profile with 3/8 inch (10 mm)

radius that forms the visible surface and an internal integrated trapezoid-perforated

09 30 50-35

anchoring leg .2. Corners:

a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with matching end caps.d. Provide with matching connectors.


Y. Schluter-DILEX-HKS1. Description: profile with integrated, roll-formed stainless steel with trapezoid-

perforated anchoring legs, connected at a 90-degree angle by a stainless steel cove-shaped section with 23/32 inch (18.5 mm) radius and 1/2 inch (12.5 mm) wide thermoplastic rubber movement zone, which together form the visible surface.





selected.4. Movement Zone Color:

a. HB - Light Beige.b. GS - Black.c. PG - Classic Grey.d. G - Grey.

2.6 MODULAR SCREED SYSTEM

A. Schluter-BEKOTEC Polyethylene Foil:1. Modular Screed System: Schluter-BEKOTEC 36 inch by 47-1/4 inch (90 cm by 120

cm) polyethylene panel, with 7/8 inch (23 mm) high integrated studs set in a grid pattern spaced 4-1/4 inch (108 mm) on center.a. Provide with matching edge strip.

B. Schluter-BEKOTEC-DRAIN Polyethylene Foil:1. Modular Screed System: Schluter-BEKOTEC 36 inch by 47-1/4 inch (90 cm by 120

cm) polyethylene panel, with evenly spaced openings and interconnected drainage channels, with 7/8 inch (23 mm) high integrated studs set in a grid pattern spaced 4-1/4 inch (108 mm) on center.a. Provide with matching edge strip.

C. Schluter-BEKOTEC Expanded Polystyrene:1. Description: 24 inch by 48 inch by 1-3/8 inch (610 mm by 1219 mm by 35 mm)

expanded polystyrene panel, with 15/16 inch (24 mm) high integrated studs set in a grid pattern spaced 4-1/4 inch (108 mm) on center.a. Provide with matching edge strip.

2.7 UNCOUPLING MEMBRANE

09 30 50-36

A. Schluter-DITRA1. Description: 1/8 inch (3 mm) thick, orange, high-density polyethylene membrane with

a grid structure of 1/2 inch by 1/2 inch (12 mm by 12 mm) square cavities, each cut back in a dovetail configuration, and a polypropylene anchoring fleece laminated to its underside. Conforms to definition for uncoupling membranes in the Tile Council of North America Handbook for Ceramic Tile Installation and is listed by cUPC to meet or exceed the requirements of the "American national standard specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation A118.10 and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467).

2. Waterproofing seaming membrane:a. Provide KERDI BAND Seams and Corners material 0.004 inch (0.1 mm) thick,

orange polyethylene membrane, with polypropylene fleece laminated on both sides.

B. Schluter-DITRA-XL1. Description: 9/32 inch (7 mm) thick, orange, high-density polyethylene membrane with

a grid structure of 1/2 inch by 1/2 inch (12 mm by 12 mm) square cavities, each cut back in a dovetail configuration, and a polypropylene anchoring fleece laminated to its underside. Conforms to definition for uncoupling membranes in the Tile Council of North America Handbook for Ceramic Tile Installation and listed by cUPC to meet or exceed the requirements of the "American national standard specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation A118.10 and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467).



C. Schluter-DITRA-HEAT1. Description: 1/4 inch (5.5 mm) thick, orange, high-density polypropylene membrane

with a cut-back stud structure, specifically designed to secure Schluter DITRA HEAT electric heating cables in place. An anchoring fleece is laminated to its underside. The membrane conforms to the definition for uncoupling membranes in the Tile Council of North America Handbook for Ceramic Tile Installation and is listed by cUPC to meet or exceed the requirements of the "American national standard specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation" A118.10 and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467).

D. Schluter-DITRA-HEAT DUO1. Description: 5/16 inch (8 mm) thick, orange, high-density polypropylene membrane

with a cut-back stud structure, specifically designed to secure Schluter-DITRA-HEAT electric heating cables in place. An integrated sound control layer and thermal break in the form of a thicker bonding fleece is laminated to its underside. When tested according to the ASTM E 2179 "Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors," a flooring assembly consisting of the membrane and porcelain tile produces a ΔIIC value of 20. The membrane conforms to the definition for uncoupling membranes in the Tile Council of North America Handbook for Ceramic Tile Installation, meets or exceeds the requirements of the ANSI A118.13 "American National Standard Specifications for Bonded Sound Reduction Membranes for Thin-Set Ceramic Tile Installation," meets or exceeds the requirements of the ANSI A118.10 "American National Standard Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installation,"

09 30 50-37

and is listed by cUPC (see File No. 4654) and evaluated by ICC-ES (see Report No. ESR-2467 and PMG 1204).

2. Thermostat:a. WiFi Touchscreen Programmable.b. Touchscreen Programmablec. Non-Programmable.

3. Heating Cable Voltage:a. 120V.b. 240V.

4. Heating Cable:a. Heating cable placement as detailed.



E. Schluter-DITRA-DRAIN1. Description: 5/32 inch (4 mm) thick, Drainage membrane designed for use with thin

bed ceramic and stone tile assemblies in exterior applications. Membrane consists of orange, high-density studded polyethylene sheet with laminated polypropylene filter fabric to the upper side.

2.8 WATERPROOFING MEMBRANE

A. Schluter-KERDI1. Description: 0.008 inch (0.2 mm) thick, orange polyethylene membrane, with

polypropylene fleece laminated on both sides, which is listed by cUPC to meet or exceed requirements of the "American national standard specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation A118.10 and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467).

2. Corners and seals:a. Provide matching preformed inside corners.b. Provide matching preformed outside corners.c. Provide matching preformed pipe seals.d. Provide matching preformed mixing valve seals.

B. Schluter-KERDI-DS1. Description: 0.020 inch (20. mils) thick, orange polyethylene membrane, with

polypropylene fleece laminated on both sides, which is listed by cUPC to meet or exceed requirements of the "American national standard specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation" A118.10 and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467).

2. Corners and seals:a. Provide matching preformed inside corners.b. Provide matching preformed outside corners.c. Provide matching preformed pipe seals.

C. Schluter-KERDI-BAND1. Description: Seams and Corners material 0.004 inch (0.1 mm) thick, orange

polyethylene membrane, with polypropylene fleece laminated on both sides.2. Width:

a. Width as required.

2.9 FLOOR DRAIN WITH INTEGRATED BONDING FLANGE

09 30 50-38

A. Schluter-KERDI-DRAIN, Plastic:1. Description: floor drain 11-25/32 inch (300 mm) diameter, trapezoid-perforated,

integrated bonding flange with polypropylene fleece thermally laminated to the surface and hubbed connection to 2 inch (50 mm) drain pipe. Grate assembly includes 4 inch by 4 inch (102 mm by 102 mm) square grate, height adjustment collar, and lateral adjustment ring with trapezoid perforations.

2. Drain listed by UPC to meet requirements of "International Association of Plumbing and Mechanical Officials Interim Guide Criteria for Floor Drain with Integrated Bonding Flange" (IGC 195), listed by CSA to meet requirements of the Canadian Standards Association standard, "Floor, Area, and Shower Drains, and Cleanouts for Residential Construction" (CSA B79), and referenced in method B422 and B422C of the Tile Council of North America Handbook for Ceramic Tile Installation.

3. Drain Housing Material:a. ABS.b. PVC.

4. Grate Material and Finish:a. Design 1 - Arc-shaped and trapezoid-shaped openings

1) E -Stainless Steel Type 3042) EP -Stainless Steel Type 304, Polished3) EOB -Stainless Steel Type 304, Oil-Rubbed Bronze4) ET -Stainless Steel Type 304, Nickel5) ECG -Stainless Steel Type 304, Classic Gold6) EVG -Stainless Steel Type 304, Vintage Gold7) ERG -Stainless Steel Type 304, Rose Gold

b. Curve - Alternating arc-shaped openings1) EB -Stainless Steel Type 304, Brushed2) EBT -Stainless Steel Type 304, Brushed Nickel3) EBCG -Stainless Steel Type 304, Brushed Classic Gold4) EBVG -Stainless Steel Type 304, Brushed Vintage Gold5) EBRG -Stainless Steel Type 304, Brushed Rose Gold6) TSC - Color Coated Aluminum, Cream7) TSBG - Color Coated Aluminum, Greige8) TSSG - Color Coated Aluminum, Stone Grey9) TSOB - Color Coated Aluminum, Bronze10) MBW - Color Coated Aluminum, Matte White11) MGS - Color Coated Aluminum, Matte Black

c. Floral - Petal-shaped openings1) EB -Stainless Steel Type 304, Brushed2) EBT -Stainless Steel Type 304, Brushed Nickel3) EBCG -Stainless Steel Type 304, Brushed Classic Gold4) EBVG -Stainless Steel Type 304, Brushed Vintage Gold5) EBRG -Stainless Steel Type 304, Brushed Rose Gold6) TSC - Color Coated Aluminum, Cream7) SBG - Color Coated Aluminum, Greige8) TSSG - Color Coated Aluminum, Stone Grey9) TSOB - Color Coated Aluminum, Bronze10) MBW - Color Coated Aluminum, Matte White11) MGS - Color Coated Aluminum, Matte Black

d. Pure - Circular opening with central slot opening1) EB -Stainless Steel Type 304, Brushed2) EBT -Stainless Steel Type 304, Brushed Nickel3) EBCG -Stainless Steel Type 304, Brushed Classic Gold4) EBVG -Stainless Steel Type 304, Brushed Vintage Gold5) EBRG -Stainless Steel Type 304, Brushed Rose Gold6) TSC - Color Coated Aluminum, Cream7) TSBG - Color Coated Aluminum, Greige

09 30 50-39

8) TSSG - Color Coated Aluminum, Stone Grey9) TSOB - Color Coated Aluminum, Bronze10) MBW - Color Coated Aluminum, Matte White11) MGS - Color Coated Aluminum, Matte Black

e. Design 2 - Arc-shaped openings1) ATGB - Anodized Aluminum, Brushed Nickel2) AKGB - Anodized Aluminum, Brushed Copper3) AMGB - Anodized Aluminum, Brushed Brass

f. ECS - Tileable Covering Support, Stainless Steel Type 3045. Nominal Grate Size:

a. 4 inch (100 mm) by 4 inch (100 mm) square.b. 6 inch (150 mm) by 6 inch (150 mm) square.c. 6 inch (150 mm) round.

6. Drain Outlet:a. 2 inch (50 mm) outlet.b. 2 inch (50 mm) horizontal outlet.c. 3 inch (75 mm) outlet.

B. Schluter-KERDI-DRAIN, Stainless Steel:1. Description: stainless steel floor drain 9-27/32 inch (250 mm) diameter integrated

bonding flange with 3 inch (75 mm) no-hub outlet, and grate assembly. Grate assembly includes stainless steel grate, height adjustment collar, and lateral adjustment ring with trapezoid perforations.

2. Drain listed by UPC to meet requirements of "International Association of Plumbing and Mechanical Officials Interim Guide Criteria for Floor Drain with Integrated Bonding Flange" (IGC 195), listed by CSA to meet requirements of the Canadian Standards Association standard, "Floor, Area, and Shower Drains, and Cleanouts for Residential Construction" (CSA B79), Drain detail as referenced in method B422 and B422C of the Tile Council of North America Handbook for Ceramic Tile Installation.

3. Drain Housing Material:a. Stainless Steel.


1) E -Stainless Steel Type 3042) EP -Stainless Steel Type 304, Polished3) EOB -Stainless Steel Type 304, Oil-Rubbed Bronze4) ET -Stainless Steel Type 304, Nickel5) ECG -Stainless Steel Type 304, Classic Gold6) EVG -Stainless Steel Type 304, Vintage Gold7) ERG -Stainless Steel Type 304, Rose Gold

b. Curve - Alternating arc-shaped openings1) EB -Stainless Steel Type 304, Brushed2) EBT -Stainless Steel Type 304, Brushed Nickel3) EBCG -Stainless Steel Type 304, Brushed Classic Gold4) EBVG -Stainless Steel Type 304, Brushed Vintage Gold5) EBRG -Stainless Steel Type 304, Brushed Rose Gold

c. TSC - Color Coated Aluminum, Cream1) TSBG - Color Coated Aluminum, Greige2) TSSG - Color Coated Aluminum, Stone Grey3) TSOB - Color Coated Aluminum, Bronze4) MBW - Color Coated Aluminum, Matte White5) MGS - Color Coated Aluminum, Matte Black

d. Floral - Petal-shaped openings1) EB -Stainless Steel Type 304, Brushed2) EBT -Stainless Steel Type 304, Brushed Nickel3) EBCG -Stainless Steel Type 304, Brushed Classic Gold

09 30 50-40

4) EBVG -Stainless Steel Type 304, Brushed Vintage Gold5) EBRG -Stainless Steel Type 304, Brushed Rose Gold6) TSC - Color Coated Aluminum, Cream7) TSBG - Color Coated Aluminum, Greige8) TSSG - Color Coated Aluminum, Stone Grey9) TSOB - Color Coated Aluminum, Bronze10) MBW - Color Coated Aluminum, Matte White11) MGS - Color Coated Aluminum, Matte Black

e. Pure - Circular opening with central slot opening1) EB -Stainless Steel Type 304, Brushed2) EBT -Stainless Steel Type 304, Brushed Nickel3) EBCG -Stainless Steel Type 304, Brushed Classic Gold4) EBVG -Stainless Steel Type 304, Brushed Vintage Gold5) EBRG -Stainless Steel Type 304, Brushed Rose Gold6) TSC - Color Coated Aluminum, Cream7) TSBG - Color Coated Aluminum, Greige8) TSSG - Color Coated Aluminum, Stone Grey9) TSOB - Color Coated Aluminum, Bronze10) MBW - Color Coated Aluminum, Matte White11) MGS - Color Coated Aluminum, Matte Black

f. Design 2 - Arc-shaped openings1) ATGB - Anodized Aluminum, Brushed Nickel2) AKGB - Anodized Aluminum, Brushed Copper3) AMGB - Anodized Aluminum, Brushed Brass

g. ECS - Tileable Covering Support, Stainless Steel Type 304.5. Nominal Grate Size:


6. Drain Outlet:a. 2 inch (50 mm) outlet.b. 2 inch Threaded stainless steel (50 mm) outlet.c. 3 inch (75 mm) outlet.

C. Schluter-KERDI-DRAIN ADAPTER KIT1. Description:

a. Floor drain adaptor kit consisting of stainless steel adaptor ring with over-molded santoprene gasket, 11-13/16 inch (300 mm) diameter sloped integrated bonding flange with thermally laminated polypropylene fleece, and grate assembly. Grate assembly includes grate, height adjustment collar, and lateral adjustment ring with trapezoid perforations. Drain detail as referenced in method B422 and B422C of the Tile Council of North America Handbook for Ceramic Tile Installation.

b. Drain type as referenced in methods B422 and B422 STONE in the Tile Council of North America Handbook for Ceramic, Glass, and Stone Tile Installation.

2. Drain Housing Material:a. ABS.b. PVC.


1) E -Stainless Steel Type 3042) EP -Stainless Steel Type 304, Polished3) EOB -Stainless Steel Type 304, Oil-Rubbed Bronze4) ET -Stainless Steel Type 304, Nickel5) ECG -Stainless Steel Type 304, Classic Gold6) EVG -Stainless Steel Type 304, Vintage Gold

09 30 50-41

7) ERG -Stainless Steel Type 304, Rose Goldb. Curve - Alternating arc-shaped openings

1) EB -Stainless Steel Type 304, Brushed2) EBT -Stainless Steel Type 304, Brushed Nickel3) EBCG -Stainless Steel Type 304, Brushed Classic Gold4) EBVG -Stainless Steel Type 304, Brushed Vintage Gold5) EBRG -Stainless Steel Type 304, Brushed Rose Gold6) TSC - Color Coated Aluminum, Cream7) TSBG - Color Coated Aluminum, Greige8) TSSG - Color Coated Aluminum, Stone Grey9) TSOB - Color Coated Aluminum, Bronze10) MBW - Color Coated Aluminum, Matte White11) MGS - Color Coated Aluminum, Matte Black

c. Floral - Petal-shaped openings1) EB -Stainless Steel Type 304, Brushed2) EBT -Stainless Steel Type 304, Brushed Nickel3) EBCG -Stainless Steel Type 304, Brushed Classic Gold4) EBVG -Stainless Steel Type 304, Brushed Vintage Gold5) EBRG -Stainless Steel Type 304, Brushed Rose Gold6) TSC - Color Coated Aluminum, Cream7) SBG - Color Coated Aluminum, Greige8) TSSG - Color Coated Aluminum, Stone Grey9) TSOB - Color Coated Aluminum, Bronze10) MBW - Color Coated Aluminum, Matte White11) MGS - Color Coated Aluminum, Matte Black

d. Pure - Circular opening with central slot opening1) EB -Stainless Steel Type 304, Brushed2) EBT -Stainless Steel Type 304, Brushed Nickel3) EBCG -Stainless Steel Type 304, Brushed Classic Gold4) EBVG -Stainless Steel Type 304, Brushed Vintage Gold5) EBRG -Stainless Steel Type 304, Brushed Rose Gold6) TSC - Color Coated Aluminum, Cream7) TSBG - Color Coated Aluminum, Greige8) TSSG - Color Coated Aluminum, Stone Grey9) TSOB - Color Coated Aluminum, Bronze10) MBW - Color Coated Aluminum, Matte White11) MGS - Color Coated Aluminum, Matte Black

e. Design 2 - Arc-shaped openings1) ATGB - Anodized Aluminum, Brushed Nickel2) AKGB - Anodized Aluminum, Brushed Copper3) AMGB - Anodized Aluminum, Brushed Brass

f. ECS - Tileable Covering Support, Stainless Steel Type 3044. Nominal Grate Size:


5. Bonding Flange Length:a. 1-9/16 inch (39.7 mm).b. 3-41/64 inch (92.4 mm).

D. Schluter-KERDI-LINE DRAIN, Brushed Stainless Steel:1. Description:

a. Linear floor drain consisting of a formed stainless steel channel body and grate assembly that can be seamlessly adjusted to tile or stone covering thickness from 1/8 inch (3 mm) to 1 inch (25 mm). The channel body features a 2-1/4 inch (57 mm) wide trough, a 2 inch (50 mm) no-hub outlet and a 7/8 inch (22

09 30 50-42

mm) wide bonding flange laminated with a collar made of the Schluter-KERDI waterproofing membrane. Drain type as referenced in methods B422 and B422 STONE in the Tile Council of North America Handbook for Ceramic, Glass, and Stone Tile Installation.

2. Channel Body Material:a. Stainless Steel 304 (1.4301 = V2A).

3. Channel Body and Grate Nominal Length:a. 20 inch (500 mm).b. 24 inch (600 mm).c. 28 inch (700 mm)d. 32 inch (800 mm).e. 36 inch (900 mm).f. 40 inch (1000 mm).g. 44 inch (1100 mm).h. 48 inch (1200 mm).i. 52 inch (130 cm).j. 56 inch (140 cm).k. 60 inch (150 cm).l. 64 inch (160 cm).m. 68 inch (170 cm).n. 72 inch (180 cm).

4. Grate Frame Height:a. 3/4 inch (19 mm).b. 1-1/8 inch (30 mm).c. Not required for Frameless Tilable Grate.d. Height as required to coordinate with tile selection and setting system selected.

5. Grate Design:a. Closed-design, brushed stainless steel 304 (1.4301 = V2A) grate with a 3/8

inch (10 mm) wide brushed stainless steel grate frame and 2-1/8 inch (54 mm) wide grate insert that together form the visible surface.

b. Brushed stainless steel 304 (1.4301 = V2A) grate with square perforations and locking mechanism with a 3/8 inch (10 mm) wide brushed stainless steel grate frame and 2-1/8 inch (54 mm) wide grate insert that together form the visible surface.

c. Frameless Tileable plate stainless steel type 304.d. Curve - Solid Stainless Steel with Curvaceous pattern openings.e. Floral - Solid Stainless Steel with Symmetrical pattern openings.f. Pure - Solid Stainless Steel with Rounded pattern openings.

6. Drain Outlet:a. Center.b. Off-set. (Not available in all lengths consult data sheet for more information)

7. Drain Grate Connector Plate:a. Brushed stainless steel 304 (1.4301 = V2A).

2.10 PREFABRICATED SHOWER COMPONENTS

A. Schluter-KERDI-SHOWER-T/-TS/-TT1. Description: Trapezoid-imprinted, prefabricated, sloped tiled shower tray base, made

of lightweight, self-extinguishing (HF-1 rating per UL-94) expanded polystyrene (PS 40), with 12-5/16 inch (313 mm) diameter removable recessed section and bonded Schluter KERDI Membrane 0.008 inch (0.2 mm) thick, which meet or exceed the requirements of the American National Standard Specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation A118.10, and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467). Meeting ANSI A118.10 as detail as referenced in method B422 of the Tile Council of North America Handbook for Ceramic Tile Installation.

09 30 50-43

2. Tray with Center Drain Placement:a. KST-965/1525 - 38 inch by 60 inch by 1-1/8 inch (97 cm by 152 cm by 29 mm).b. KST-1220/1525 - 48 inch by 60 inch by 1-3/32 inch (1220 mm by 1525 mm by

28 mm).c. KST-1220/1830 - 48 inch by 72 inch by 1-1/4 inch (1220 mm by 1830 mm by 32

mm).d. KST-1525 - 60 inch by 60 inch by 1-3/16 inch (1525 mm by 1525 mm by 30

mm).e. KST-1830 - 72 inch by 72 inch by 1-1/2 inch (1830 mm by 1830 mm by 38

mm).f. KST-965/1525 - 38 inch by 60 inch by 1-1/8 inch (97 cm by 152 cm by 29 mm).g. KST-1220/1525 - 48 inch by 60 inch by 1-3/32 inch (122 cm by 152 cm by 28

mm).h. KST-1220/1830 - 48 inch by 72 inch by 1-1/4 inch (122 cm by 183 cm by 32

mm).i. KST-1525 - 60 inch by 60 inch by 1-3/16 inch (152 cm by 152 cm by 30 mm).j. KST-1830 - 72 inch by 72 inch by 1-1/2 inch (183 cm by 183 cm by 32 mm).

3. Tray with Off Center Drain Placement:a. KST-965/1525S - 38 inch by 60 inch by 1-1/2 inch (97 cm by 152 cm by 38

mm).4. Thin Tray:

a. KST-965/810BF - 32 inch by 38 inch by 29/32 inch (81 cm by 97 cm by 23 mm).

b. KST-915/1220BF - 36 inch by 48 inch by 1 inch (91cm by 122 cm by 25 mm).c. KST- 915BF - 36 inch by 36 inch by 7/8 inch (91 cm by 91 cm by 22 mm).d. KST- 965BF - 38 inch by 38 inch by 29/32 inch (97 cm by 97 cm by 23 mm).e. KST-1220BF - 48 inch by 48 inch by 1 inch (122 cm by 122 cm by 25 mm)f. KST-965NA/BF - 38 inch by 38 inch by 1 1/32 inch Neo Angle Off Center (97

cm by 97 cm by 26 mm).

B. Schluter-KERDI-SHOWER-L/-LS1. Description: trapezoid-imprinted, prefabricated, sloped tiled shower tray base, made

of 2.75 lb/ft3 (44 kg/m3) density, self-extinguishing (HF-1 rating per UL-94) expanded polystyrene, with removable recessed section and bonded Schluter KERDI Membrane 0.008 inch (0.2 mm) thick, which meet or exceed the requirements of the American National Standard Specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation A118.10, and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467). Meeting ANSI A118.10 as detail as referenced in method B422 of the Tile Council of North America Handbook for Ceramic Tile Installation.

2. Tray for Center Linear Drain Placement:a. KSLT1000 - 39 inch by 39 inch by 32 by 1-1/4 inch (100 cm by 100 cm by 32

mm).b. KSLT1220 - 48 inch by 48 inch by 1-3/8 inch (122 cm by 122 cm by 34 mm).c. KSLT1395 - 55 inch by 55 inch by 1-7/16 inch (140 cm by 140 cm by 36 mm).

3. Tray for Wall or Entrance Linear Drain Placement:a. KSLT-1000S - 39 inch by 39 inch by 21/32 inch (100 cm by 100 cm by 42 mm).b. KSLT-1220S - 48 inch by 48 inch by 1 13/16 inch (122 cm by 122 cm by 46

mm).c. KSLT-1395S - 55 inch by 55 inch by 2 inch (140 cm by 140 cm by 50 mm).d. KSLT-915/1395S - 36 inch by 55 inch by 2 inch (91 cm by 140 cm by 50 mm).e. KSLT-965/1830S - 36 inch by 72 inch by 2-5/16 inch (91 cm by 183 cm by 58

mm).f. KSLT-965/1930S - 38 inch by 76 inch by 2-3/8 inch (97 cm by 193 cm by 60

mm).g. KSLT1930/965S - 76 inch by 38 inch by 1-5/8 inch (193 cm by 97 cm by 41

09 30 50-44

mm).

C. Schluter-KERDI-SHOWER-SC1. Description: trapezoid-imprinted, prefabricated, tiled shower curb base, made of 2.75

lb/ft3 (44 kg/m3) density, self-extinguishing (HF-1 rating per UL-94) expanded polystyrene.

2. Curb dimensions are 48 inch by 6 inch by 4-1/2 inch (1220 mm by 150 mm by 115 mm).

D. Schluter-KERDI-BOARD-SC1. Description: Prefabricated waterproof Shower Curb, constructed of rigid extruded

polystyrene foam building element panel, with reinforcement material and polypropylene fleece webbing laminated on both sides for thin-set ceramic tile and dimension stone Installations.

2. Size:a. KBSC 115 150 970 - 38 inch by 6 inch by 4-1/2 inch (970 mm by 150 mm by

115 mm).b. KBSC 115 150 1220 - 48 inch by 6 inch by 4-1/2 inch (122 cm by 150 mm by

115 mm).c. KBSC 115 150 1524 - 60 inch by 6 inch by 4-1/2 inch (152 cm by 150 mm by

115 mm).

E. Schluter-KERDI-SHOWER-SR1. Description: trapezoid-imprinted, prefabricated, tiled shower ramp base, made of 2.75

lb/ft3 (44 kg/m3) density, self-extinguishing (HF-1 rating per UL-94) expanded polystyrene.

2. Ramp dimensions are 48 inch by 15-7/8 inch (1220 mm by 40 mm) with slope from maximum thickness of 1-1/2 inch (38 mm) to minimum thickness of 1/4 inch (6 mm).

F. Schluter-KERDI-BOARD-SB1. Description: Prefabricated waterproof bench, constructed of rigid extruded polystyrene

foam building element panel, with reinforcement material and polypropylene fleece webbing laminated on both sides for thin-set ceramic tile and dimension stone Installations.

2. Size:a. KBSC 115 150 970 - 38 inches by 6 inches by 4-1/2 inches (970 mm by 150

mm by 115 mm).b. KBSC 115 150 1220 - 48 inches by 6 inches by 4-1/2 inches (122 cm by 150

mm by 115 mm).c. KBSC 115 150 1524 - 60 inches by 6 inches by 4-1/2 inches (152 cm by 150

mm by 115 mm).

G. Schluter-KERDI-BOARD-SN1. Description: Prefabricated waterproof niche, constructed of rigid extruded polystyrene

foam building element panel, with reinforcement material and polypropylene fleece webbing laminated on both sides for thin-set ceramic tile and dimension stone Installations.

2. Size:a. KB 12 SN 305 152 A - 12 inches by 6 inches by 3-1/2 inches (305 mm by 152

mm by 89 mm)b. KB 12 SN 305 305 A - 12 inches by 12 inches by 3-1/2 inches (305 mm by 305

mm by 89 mm)c. KB 12 SN 305 508 A1 - 12 inches by 20 inches by 3-1/2 inches (305 mm by

508 mm by 89 mm)d. KB 12 SN 305 711 A1 - 12 inches by 28 inches by 3-1/2 inches (305 mm by

711 mm by 89 mm)

09 30 50-45

H. Schluter-KERDI-FIX1. Description: single-component, elastomeric, waterproof sealing and bonding

compound with a silane-modified polymer base. Compound is free of solvents and odorless.

2. Color:a. BW - Bright White.b. G - Grey.

2.11 WATERPROOF BUILDING PANEL FOR CERAMIC AND STONE TILE

A. Schluter-KERDI-BOARD1. Description: Rigid extruded polystyrene foam building element panel, with

reinforcement material and polypropylene fleece webbing laminated on both sides for thin-set ceramic tile and dimension stone Installations.

2. Panel Thickness:a. Thickness as required.

3. Panel Size:a. 48 inch by 64 inch (122 by 162.5 cm).b. 48 inch by 96 inch (122 by 244 cm).c. 24-1/2 inch by 96 inch (62.5 by 244 cm).

2.12 DRAINAGE MEMBRANES

A. Schluter-TROBA-PLUS1. Description: orange polyethylene sheet with 5/16 inch (8 mm) high, truncated cone-

shaped studs, covered with a polypropylene water-permeable filter fabric.

2.13 FINISHING AND TRANSITION PROFILES FOR SHOWERS

A. Schluter-SHOWERPROFILE-S1. Description: two-part profile with an exposed brushed stainless steel tapered edge

and recycled PVC support section with integrated trapezoid-perforated anchoring leg for lateral transitions between sloped shower floors and walls.

2. Profile Height:a. Height as required to coordinate with tile selection and tile setting system

selected.3. Profile Length:

a. Length as required.

B. Schluter-SHOWERPROFILE-R1. Description: two-part profile with an adjustable brushed stainless steel exposed

surface for transitions between the tiled floors and the KERDI-LINE Drain.2. Profile Height:

a. Height as required.3. Profile Length:

a. Length as required.

C. Schluter-SHOWERPROFILE-WS1. Description: two-part splashguard profile with a 3/4 inch (19 mm) wide anodized

aluminum support section and PVC insert that together form the visible surface between the tiled floors and walls.

2. Splashguard Insert:a. Semi-circular Lip.b. Collapsible Straight Lip.

D. Schluter-SHOWERPROFILE-WSK1. Description: two-part splashguard profile with a 2-1/6 inch (52 mm) wide 5/16 inch (8

09 30 50-46

mm) tall anodized aluminum support section and PVC insert that together form the visible surface.

2. Splashguard Insert:a. Semi-circular Lip.b. Collapsible Straight Lip.

E. Schluter-DECO-SG1. Description: Prefabricated channel reveal profile with 1/8 inch (3 mm) wide vertical

side sections and channel that together form the exposed shadow gap reveal, integrated trapezoid perforated anchoring leg.


1) Height as required to coordinate with tile selection and tile setting system selected.

b. ACG - Polished Chrome Anodized Aluminum.1) Height as required to coordinate with tile selection and tile setting system

selected.c. E - Stainless Steel 304.


d. Reveal Width:1) 1/2 inch (12.5 mm).2) 9/16 inch (15 mm).

2.14 SHOWER SHELF

A. Schluter-SHELF1. Description: Wall shelf system consisting of 5/32 inch (4 mm) thick shelves for

installation with tile on wall surfaces.2. Configuration and Size:

a. SHELF-E Corner Shelf:1) 8-1/4 inches (210 mm) by 8-1/4 inches (210 mm) triangle2) 11-5/8 inches (295 mm) by 6-1/16 inches (154 mm) by 2-7/16 inches (62

mm) offset rectangle3) 7-11/16 inches (195 mm) by 3 inches (75 mm) pentagon

b. SHELF-W Wall Shelf:1) 11-13/16 inches (300 mm) by 4-1/2 inches (115 mm) rectangle

c. SHELF-N Niche Shelf:1) 11-13/16 inches (300 mm) by 3-7/16 inches (87 mm) rectangle

3. Design:a. Curve - Curvaceous pattern openingsb. Floral - Symmetrical pattern openings

4. Material and Finisha. EB - Brushed Stainless Steel Type 304 = V2Ab. TSC - Color Coated Aluminum, Creamc. TSBG - Color Coated Aluminum, Greiged. TSSG - Color Coated Aluminum, Stone Greye. TSOB - Color Coated Aluminum, Bronzef. MBW - Color Coated Aluminum, Matte White

2.15 FINISHING AND EDGE-PROTECTION PROFILES AND GUTTERS FOR BALCONIES AND TERRACES

A. Schluter-BARA-ESOT1. Description: stainless steel type 304 = V2A, L-shaped profile with a trapezoid-

perforated anchoring leg and circle-perforated vertical section.2. Height:

09 30 50-47

a. 2-3/8 inch (60 mm).b. 4-3/8 inch (110 mm).c. Height as required.

B. Schluter-BARA-RW1. Description: L-shaped profile with a 3-1/2 inch (90 mm) wide integrated trapezoid-

perforated anchoring leg.a. Provide with straight anchoring leg.b. Provide with special radius anchoring leg for radius applications.c. Provide with matching connector.


1) Height as required.b. AC - Color-coated Aluminum.

1) BW - Bright White.a) Height as required.

2) HB - Light Beige.a) Height as required.

3) RB - Red Brown.a) Height as required.

4) SB - Black Brown.a) Height as required.

5) PG - Classic Grey.a) Height as required.

6) GM - Metallic Grey.a) Height as required.

C. Schluter-BARA-RWL1. Description: L-shaped profile with a 3-1/2 inch (90 mm) wide integrated trapezoid-

perforated anchoring leg and weep holes spaced at 2-15/16 inch (75 mm), that forms the visible surface.

2. Anchoring Leg:a. Provide with straight anchoring leg.b. Provide with special radius anchoring leg for radius applications.c. Provide with matching connector.

3. Material and Finish:a. AC - Color-coated Aluminum.

1) PG - Classic Grey.a) Height as required.

2) GM - Metallic Grey.a) Height as required.

D. Schluter-BARA-RAK1. Description: color-coated aluminum profile with a 3-1/8 inch (80 mm) wide integrated

trapezoid-perforated anchoring leg, 2 inch (50 mm) tall vertical section, and 1-3/32 inch (28 mm) tall drip lip with 1-1/16 inch (27 mm) offset from the vertical section.

2. Corners:a. Provide with matching inside corners.b. Provide with matching outside corners.c. Provide with matching connector.

3. Color:a. BW - Bright White.b. HB - Light Beige.c. RB - Red Brown.d. SB - Black Brown.e. PG - Classic Grey.

09 30 50-48

f. GM - Metallic Grey.

2.16 SETTING MATERlALS

A. Schluter-SET Premium Unmodified Thin Set Mortar.1. Description: premium unmodified sag-resistant thin-set mortar specifically formulated

for use with Schluter membranes and boards. Schluter-SET is suitable for use with ceramic, porcelain, and stone tile, including large and heavy tile, in conjunction with Schluter-Systems' uncoupling and waterproofing membranes. Meets the requirements of ANSI A118.1T.

2. Color:a. White.b. Grey.

B. Schluter-ALL SET Modified Thin Set Mortar.1. Description: specialized sag-resistant modified thin-set mortar specifically formulated

for use with Schluter membranes and boards. It is engineered for use both under and over all DITRA and KERDI products. ALL-SET is suitable for use with ceramic, porcelain, and stone tile, including large and heavy tile, in conjunction with Schluter-Systems' uncoupling and waterproofing membranes. Meets the requirements of ANSI A118.4T, A118.11, and A118.15T.


C. Schluter-FAST SET Rapid Setting Thin Set Mortar.1. Description: specialized rapid-setting sag-resistant modified thin-set mortar

specifically formulated for use with Schluter membranes and boards. It is engineered for use both under and over all DITRA and KERDI products. FAST-SET is suitable for use with ceramic, porcelain, and stone tile, including large and heavy tile, in conjunction with Schluter-Systems' uncoupling and waterproofing membranes. Meets the requirements of ANSI A118.4TF, A118.11, and A118.15TF.


2.17 EDGE-PROTECTION AND TRANSITION PROFILES FOR RESILIENT COVERINGS

A. Schluter-VINPRO-S1. Description: J-shaped profile with 1/4 inch (6 mm) wide visible surface and integrated

perforated tapered anchoring leg.2. Material and Finish:

a. ACGB - Brushed Chrome Anodized Aluminum.1) Height as required to coordinate with resilient covering and setting

system selected.b. ATGB - Brushed Nickel Anodized Aluminum.

1) Height as required to coordinate with resilient covering selection and setting system selected.

c. ABGB - Brushed Antique Bronze Aluminum.1) Height as required to coordinate with resilient covering and setting

system selected.

B. Schluter-VINPRO-T1. Description: T-shaped Anodized Aluminum profile with 17/32 inch (14 mm) wide

visible surface, 1/16 inch (1 mm) thick beveled exposed surface and 1/8 inch (3 mm) tall anchoring leg.

2. Material and Finish:

09 30 50-49



1) Height as required to coordinate with resilient covering and setting system selected.


system selected.

C. Schluter-VINPRO-STEP1. Description: Stair Nosing profile with flat exposed vertical face, 1/4 Inch (6 mm) wide

ribbed squared exposed top surface and, integrated perforated tapered anchoring leg.2. Material and Finish:





system selected.

D. Schluter-VINPRO-U1. Description: Transition profile with sloped exposed surface and integrated perforated

tapered anchoring leg.2. Material and Finish:





system selected.

E. Schluter-VINPRO-RO1. Description: Bullnose-type profile with symmetrically rounded visible surface with 1/4

inch (6 mm) radius, and integrated perforated tapered anchoring leg.2. Material and Finish:





system selected.

PART 3 EXECUTION

3.1 EXAMINATION

A. Do not begin installation until substrates have been properly prepared.

09 30 50-50

B. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

A. Clean surfaces thoroughly prior to installation.

B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

A. Install in accordance with manufacturer's instructions.

3.4 PROTECTION

A. Protect installed products until completion of project.

B. Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

09 30 50-51

· web viewlinear floor drain consisting of a formed stainless steel channel body and grate...

Documents