· web viewheight as required. schluter-bara-rwl description: l-shaped profile with a 3-1/2 inch...

SECTION 09 30 05TILE SETTING MATERIALS AND ACCESSORIES

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2007 - 2007 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Edge-protection and transition profiles for floors.

1.1.2 Finishing and edge-protection profiles for walls and countertops.

1.1.3 Wall access panel system.

1.1.4 Finishing and edge-protection profiles for stair nosings.

1.1.5 Movement joint and cove-shaped profiles.

1.1.6 Modular screed system.

1.1.7 Uncoupling membrane.

1.1.8 Waterproofing Membrane.

1.1.9 Floor drain, with integrated bonding flange.

1.1.10 Shower waterproofing: prefabricated substrates, waterproofing membrane, floor drain with integrated bonding flange, and sealant.

1.1.11 Drainage membranes.

1.1.12 Finishing and edge-protection profiles and gutters for balconies and terraces.

1.1.13 Setting materials: adhesives, mortars, grouts, and sealants.

1.2 RELATED SECTIONS

1.2.1 Section 03 30 00 - Cast-in-Place Concrete.

1.2.2 Section 05 55 00 - Metal Stair Treads and Nosings.

1.2.3 Section 06 10 00 - Rough Carpentry.

1.2.4 Section 07 90 00 - Joint Protection.

1.2.5 Section 09 29 00 - Gypsum Board.

09 30 05-1

1.2.6 Section 09 30 00 - Tiling.

1.2.7 Section 10 26 13 - Corner Guards.

1.2.8 Section 22 30 00 - Plumbing Equipment.

1.2.9 Section _____ - Radiant Heating Units: electric cables, electric mats, and hydronic piping.

1.3 REFERENCES

1.3.1 CSA B79-08: Floor, Area, and Shower Drains, and Cleanouts for Residential Construction.

1.3.2 IAPMO IGC 195: Interim Guide Criteria for Floor Drain with Integrated Bonding Flange.

1.3.3 Tile Council of North America (TCNA) Handbook for Ceramic Tile Installation.

1.3.4 Terrazzo, Tile and Marble Association of Canada (TTMAC) Specification Guide 09300 Tile Installation Manual.

1.3.5 American National Standard Specifications for the installation of ceramic tile A108 / A118 / A136.1.

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00.

1.4.2 Product Data: Manufacturer's data sheets on each product to be used, including:1.4.2.1 Preparation instructions and recommendations.1.4.2.2 Storage and handling requirements and recommendations.1.4.2.3 Installation methods.

1.4.3 Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) long, representing actual product, color, and finish.

1.4.4 Manufacturer's Certificates: Certify products meet or exceed specified requirements.

1.5 QUALITY ASSURANCE

1.5.1 Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with minimum ten years experience.

1.5.2 Installer Qualifications: Company specializing in performing the work of this section with minimum five years experience.

1.5.3 Source Limitations for Setting Materials and Accessories: Obtain product of a uniform quality for each application condition from a single manufacturer.

1.5.4 Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.1.5.4.1 Finish areas designated by Architect.1.5.4.2 Do not proceed with remaining work until workmanship, color, and sheen are

approved by Architect.1.5.4.3 Refinish mock-up area as required to produce acceptable work.

1.5.5 Preinstallation Conference: Conduct conference at the Project site.1.5.5.1 Convene one week prior to commencing work of this section.1.5.5.2 Require attendance of installation material manufacturer, tile supplier, tile

installer and installers of related work. Review installation procedures and

09 30 05-2

coordination required with related work.1.5.5.3 Meeting agenda includes but is not limited to:

1.5.5.3.1 Surface preparation.1.5.5.3.2 Tile and installation material compatibility.1.5.5.3.3 Edge protection, transition and pre-fabricated movement joint profiles.1.5.5.3.4 Waterproofing techniques.1.5.5.3.5 Crack isolation techniques.

1.6 DELIVERY, STORAGE, AND HANDLING

1.6.1 Store products in manufacturer's unopened packaging until ready for installation.

1.6.2 Protect materials from exposure to moisture. Do not deliver until after wet work is complete and dry.

1.6.3 Store materials in a dry, warm, ventilated weathertight location.

1.7 PROJECT CONDITIONS

1.7.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

1.8 COORDINATION

1.8.1 Coordinate Work with other operations and installation of floor finish materials to avoid damage to installed materials.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: Schluter Systems, L.P., 194 Pleasant Ridge Road, Plattsburgh, NY 12901-5841. ASD. Tel: (800) 472-4588. Fax (800) 477-9783. E-mail:[email protected]. Web:www.schluter.com.

2.1.2 Acceptable Manufacturer: Schluter Systems (Canada) Inc., 21100 Chemin Ste-Marie, Ste-Anne-de-Bellevue, QC H9X 3Y8. Tel: (800) 667-8746. Fax (514) 336-2410. E-mail:[email protected]. Web:www.schluter.com.

2.1.3 Substitutions: Not permitted.

2.1.4 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00.

2.2 EDGE-PROTECTION AND TRANSITION PROFILES FOR FLOORS

2.2.1 Schluter-SCHIENE2.2.1.1 Description: L-shaped profile with 1/8 inch (3.2 mm) wide visible surface

integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.2.2.1.2 Anchoring Leg:

2.2.1.2.1 Provide with straight anchoring leg.2.2.1.2.2 Provide with special radius anchoring leg for radius applications.

2.2.1.3 Material and Finish:2.2.1.3.1 EV4A - Stainless Steel Type 316 L = V4A.

2.2.1.3.1.1 Height as required to coordinate with tile selection and setting system selected.

2.2.1.3.2 E - Stainless Steel Type 304 = V2A.

09 30 05-3


2.2.1.3.3 M - Solid Brass.2.2.1.3.3.1 Height as required to coordinate with tile selection and setting

system selected.2.2.1.3.4 A - Aluminum.


2.2.1.3.5 AE - Satin Anodized Aluminum.2.2.1.3.5.1 Height as required to coordinate with tile selection and setting

system selected.2.2.1.3.6 ACB - Bright Chrome Anodized Aluminum.


2.2.1.3.7 ATB - Bright Nickel Anodized Aluminum.2.2.1.3.7.1 Height as required to coordinate with tile selection and setting

system selected.2.2.1.3.8 AKB - Bright Copper/Bronze Anodized Aluminum.


2.2.1.3.9 AMB - Bright Brass Anodized Aluminum.2.2.1.3.9.1 Height as required to coordinate with tile selection and setting

system selected.

2.2.2 Schluter-DECO2.2.2.1 Description: profile with 1/4 inch (6 mm) wide visible surface and integrated

trapezoid-perforated anchoring leg.2.2.2.2 Anchoring Leg:


2.2.2.3 Material and Finish:2.2.2.3.1 E - Stainless Steel Type 304 = V2A.



system selected.2.2.2.3.3 MC - Chrome-plated Solid Brass.



system selected.

2.2.3 Schluter-RENO-T2.2.3.1 Description: T-shaped profile with 1/16 inch (1 mm) thick beveled exposed

surface and 11/32 inch (9 mm) tall integrated vertical anchoring leg.2.2.3.2 Material and Finish:

2.2.3.2.1 E - Stainless Steel Type 304 = V2A.2.2.3.2.1.1 Width as required.

2.2.3.2.2 EB - Brushed Stainless Steel Type 304 = V2A.2.2.3.2.2.1 Width as required.

2.2.3.2.3 M - Solid Brass.2.2.3.2.3.1 Width as required.

2.2.3.2.4 AE - Satin Anodized Aluminum.2.2.3.2.4.1 Width as required.

09 30 05-4

2.2.3.2.5 AT - Satin Nickel Anodized Aluminum.2.2.3.2.5.1 Width as required.

2.2.3.2.6 AK - Satin Copper/Bronze Anodized Aluminum.2.2.3.2.6.1 Width as required.

2.2.3.2.7 AM - Satin Brass Anodized Aluminum.2.2.3.2.7.1 Width as required.

2.2.4 Schluter-RENO-TK2.2.4.1 Description: profile with sloped exposed surface, 1/4 inch (6 mm) deep channel

below exposed surface, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2.2.4.2 Anchoring Leg:2.2.4.2.1 Provide with straight anchoring leg.2.2.4.2.2 Provide with special radius anchoring leg for radius applications.



2.2.4.3.2 EB - Brushed Stainless Steel Type 304 = V2A.2.2.4.3.2.1 Height as required to coordinate with tile selection and setting

system selected.2.2.4.3.3 M - Solid Brass.



system selected.2.2.4.3.5 ACB - Bright Chrome Anodized Aluminum.


2.2.4.3.6 AT - Satin Nickel Anodized Aluminum.2.2.4.3.6.1 Height as required to coordinate with tile selection and setting

system selected.2.2.4.3.7 AK - Satin Copper/Bronze Anodized Aluminum.


2.2.4.3.8 ATGB - Brushed Nickel Anodized Aluminum.2.2.4.3.8.1 Height as required to coordinate with tile selection and setting

system selected.2.2.4.3.9 AKGB - Brushed Copper/Bronze Anodized Aluminum.


2.2.4.3.10 ABGB - Brushed Antique Bronze Anodized Aluminum.2.2.4.3.10.1 Height as required to coordinate with tile selection and setting

system selected.2.2.4.3.11 AMB - Bright Brass Anodized Aluminum.


2.2.5 Schluter-RENO-U2.2.5.1 Description: profile with sloped exposed surface, 5/32 inch (4 mm) tall leading

edge, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.


2.2.5.2.1.1 Height as required to coordinate with tile selection and setting

09 30 05-5

system selected.2.2.5.2.2 EB - Brushed Stainless Steel Type 304 = V2A.



system selected.2.2.5.2.4 AE - Satin Anodized Aluminum.


2.2.5.2.5 ACB - Bright Chrome Anodized Aluminum.2.2.5.2.5.1 Height as required to coordinate with tile selection and setting

system selected.2.2.5.2.6 AT - Satin Nickel Anodized Aluminum.


2.2.5.2.7 AK - Satin Copper/Bronze Anodized Aluminum.2.2.5.2.7.1 Height as required to coordinate with tile selection and setting

system selected.2.2.5.2.8 ATGB - Brushed Nickel Anodized Aluminum.





2.2.5.2.11 AM - Satin Brass Anodized Aluminum.2.2.5.2.11.1 Height as required to coordinate with tile selection and setting



2.2.5.2.13 TSOB - Tuscan Bronze Color-coated Aluminum.2.2.5.2.13.1 Height as required to coordinate with tile selection and setting

system selected.

2.2.6 Schluter-RENO-RAMP-K2.2.6.1 Description: anodized aluminum profile with textured, sloped exposed surface,

tapered leading edge and integrated grout joint spacer.2.2.6.2 Material and Finish:

2.2.6.2.1 AE - Satin Anodized Aluminum.2.2.6.3 Height: 1/2 inch (12.5 mm).2.2.6.4 Ramp Length: 2-1/2 inch (64 mm)

2.2.7 Schluter-RENO-RAMP2.2.7.1 Description: anodized aluminum profile with textured, sloped exposed surface,

tapered leading edge, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2.2.7.2 Material and Finish:2.2.7.2.1 AE - Satin Anodized Aluminum.

2.2.7.3 Height: 3/8 inch (10 mm).2.2.7.4 Height: 1/2 inch (12.5 mm).2.2.7.5 Height: 9/16 inch (15 mm).2.2.7.6 Height: 3/4 inch (20 mm).

09 30 05-6

2.2.7.7 Height as required.2.2.7.8 Ramp Length: 2-1/2 inch (64 mm) Only available in 3/8 inch (10 mm) and 1/2

inch (12.5 mm) heights.2.2.7.9 Ramp Length: 3-1/2 in (89 mm). Only available in 1/2 inch (12.5 mm), 9/16 inch

(15 mm) and 3/4 inch (20 mm) heights.2.2.7.10 Ramp Length: As required.

2.2.8 Schluter-RENO-V2.2.8.1 Description: ball-and-socket hinged profile with sloped exposed surface, tapered

leading edge, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.




system selected.2.2.8.3 Ramp Length: 3/4 inch (20 mm).2.2.8.4 Ramp Length: 1-3/16 in (30 mm).2.2.8.5 Ramp Length: 1-9/16 in (40 mm).2.2.8.6 Ramp Length: As required.

2.3 FINISHING AND EDGE-PROTECTION PROFILES FOR WALLS AND COUNTERTOPS

2.3.1 Schluter-JOLLY2.3.1.1 Description: L-shaped profile with 1/8 inch (3.2 mm) wide top section vertical wall

section that together form the visible surface, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2.3.1.2 Anchoring Leg:2.3.1.2.1 Provide with straight anchoring leg.2.3.1.2.2 Provide with special radius anchoring leg for radius applications.

2.3.1.3 Material and Finish:2.3.1.3.1 MC - Chrome-plated Solid Brass.


2.3.1.3.2 ACG - Polished Chrome Anodized Aluminum.2.3.1.3.2.1 Height as required to coordinate with tile selection and setting

system selected.2.3.1.3.3 ACGB - Brushed Chrome Anodized Aluminum.



system selected.2.3.1.3.5 ATG - Polished Nickel Anodized Aluminum.





2.3.1.3.8 AKG - Polished Copper/Bronze Anodized Aluminum.2.3.1.3.8.1 Height as required to coordinate with tile selection and setting

09 30 05-7




system selected.2.3.1.3.11 AM - Satin Brass Anodized Aluminum.


2.3.1.3.12 AMG - Polished Brass Anodized Aluminum.2.3.1.3.12.1 Height as required to coordinate with tile selection and setting

system selected.2.3.1.3.13 AMGB - Brushed Brass Anodized Aluminum.


2.3.1.3.14 AGRB - Brushed Graphite Anodized Aluminum.2.3.1.3.14.1 Height as required to coordinate with tile selection and setting

system selected.2.3.1.3.15 AGSG - Bright Black Anodized Aluminum.


2.3.1.3.16 AC - Color-coated Aluminum.2.3.1.3.16.1 BW - Bright White.

2.3.1.3.16.1.1 Height as required to coordinate with tile selection and setting system selected.

2.3.1.3.16.2 W - White.2.3.1.3.16.2.1 Height as required to coordinate with tile selection and

setting system selected.2.3.1.3.16.3 SP - Sand Pebble.


2.3.1.3.16.4 BH - Bahama.2.3.1.3.16.4.1 Height as required to coordinate with tile selection and

setting system selected.2.3.1.3.16.5 HB - Light Beige.


2.3.1.3.16.6 HG - Light Grey.2.3.1.3.16.6.1 Height as required to coordinate with tile selection and

setting system selected.2.3.1.3.16.7 PG - Classic Grey.


2.3.1.3.16.8 G - Grey.2.3.1.3.16.8.1 Height as required to coordinate with tile selection and

setting system selected.2.3.1.3.16.9 RB - Red Brown.


2.3.1.3.16.10 SB - Black Brown.2.3.1.3.16.10.1 Height as required to coordinate with tile selection and

setting system selected.2.3.1.3.17 P - PVC.

2.3.1.3.17.1 BW - Bright White.2.3.1.3.17.1.1 Height as required to coordinate with tile selection and

09 30 05-8

setting system selected.2.3.1.3.17.2 W - White.


2.3.1.3.17.3 SP - Sand Pebble.2.3.1.3.17.3.1 Height as required to coordinate with tile selection and

setting system selected.2.3.1.3.17.4 BH - Bahama.


2.3.1.3.17.5 HB - Light Beige.2.3.1.3.17.5.1 Height as required to coordinate with tile selection and

setting system selected.2.3.1.3.17.6 HG - Light Grey.


2.3.1.3.17.7 PG - Classic Grey.2.3.1.3.17.7.1 Height as required to coordinate with tile selection and

setting system selected.2.3.1.3.17.8 G - Grey.


2.3.1.3.17.9 GS - Black.2.3.1.3.17.9.1 Height as required to coordinate with tile selection and

setting system selected.

2.3.2 Schluter-SCHIENE2.3.2.1 Description: L-shaped profile with 1/8 inch (3.2) wide visible surface, integrated

trapezoid-perforated anchoring leg, and integrated grout joint spacer.2.3.2.2 Anchoring Leg:




2.3.2.3.2 E - Stainless Steel Type 304 = V2A.2.3.2.3.2.1 Height as required to coordinate with tile selection and setting



2.3.2.3.4 A - Aluminum.2.3.2.3.4.1 Height as required to coordinate with tile selection and setting



2.3.2.3.6 ACB - Bright Chrome Anodized Aluminum.2.3.2.3.6.1 Height as required to coordinate with tile selection and setting

system selected.2.3.2.3.7 ATB - Bright Nickel Anodized Aluminum.


2.3.2.3.8 AKB - Bright Copper/Bronze Anodized Aluminum.2.3.2.3.8.1 Height as required to coordinate with tile selection and setting

09 30 05-9



2.3.3 Schluter-QUADEC2.3.3.1 Description: profile with square visible surface, integrated trapezoid-perforated

anchoring leg, and integrated grout joint spacer.2.3.3.2 Corners:

2.3.3.2.1 Provide with matching inside corners.2.3.3.2.2 Provide with matching outside corners.2.3.3.2.3 Provide with internal connectors.










system selected.2.3.3.3.7 TSB - Tuscan Beige Color-coated Aluminum.



system selected.2.3.3.3.9 TSG - Tuscan Pewter Color-coated Aluminum.


2.3.4 Schluter-INDEC2.3.4.1 Description: Anodized aluminum profile with a square recessed reveal for

outside corners of tiled walls, integrated trapezoid-perforated anchoring leg.2.3.4.2 Corners:

2.3.4.2.1 Provide with matching outside corners.2.3.4.3 Material and Finish:

2.3.4.3.1 AE - Satin Anodized Aluminum.2.3.4.3.2 ACG - Polished Chrome Anodized Aluminum.

2.3.4.4 Profile Height:2.3.4.4.1 Height as required to coordinate with tile selection and setting system

selected.

2.3.5 Schluter-DECO-DE2.3.5.1 Description: roll-formed stainless steel finishing and edge-protection profile with

a 135 degree reveal for outside corners of tiled walls. Profile features an

09 30 05-10

integrated trapezoid perforated anchoring leg.2.3.5.2 Material and Finish:

2.3.5.2.1 E - Stainless Steel 3042.3.5.2.2 EB - Brushed Stainless Steel 304.

2.3.5.3 Profile Height:2.3.5.3.1 Height as required to coordinate with tile selection and tile setting system

selected.

2.3.6 Schluter-DECO-SG2.3.6.1 Description: anodized aluminum channel reveal profile with 1/8 inch (3 mm) wide

vertical side sections and 1/2 inch (12 mm) wide channel that together form the exposed shadow gap reveal, integrated trapezoid perforated anchoring leg.




system selected.

2.3.7 Schluter-QUADEC-FS2.3.7.1 Description: anodized aluminum, double-rail profile with 3/8 inch (10mm) -wide,

square exposed surfaces separated by a 2 inch (51 mm) -wide recessed section with dovetail channel.

2.3.7.2 Corners:2.3.7.2.1 Provide with matching inside corners.2.3.7.2.2 Provide with matching outside corners.2.3.7.2.3 Provide with end caps for exposed edges.


2.3.7.3.1.1 5/16 inch (8 mm).2.3.7.3.2 AT - Satin Nickel Anodized Aluminum.

2.3.7.3.2.1 5/16 inch (8 mm).2.3.7.3.3 ABGB - Brushed Antique Bronze Anodized Aluminum.

2.3.7.3.3.1 5/16 inch (8 mm).

2.3.8 Schluter-RONDEC2.3.8.1 Description: bullnose-type profile with symmetrically rounded visible surface with

1/4 inch (6 mm) radius, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2.3.8.2 Corners:2.3.8.2.1 Provide with matching inside corners.2.3.8.2.2 Provide with matching outside corners.2.3.8.2.3 Provide with matching internal connectors.






2.3.8.3.4 MC - Chrome-plated Solid Brass.2.3.8.3.4.1 Height as required to coordinate with tile selection and setting

09 30 05-11









2.3.8.3.10 AGB - Brushed Nickel Anodized Aluminum.2.3.8.3.10.1 Height as required to coordinate with tile selection and setting







system selected.2.3.8.3.15 AMG - Polished Brass Anodized Aluminum.


2.3.8.3.16 AMGB - Brushed Brass Anodized Aluminum.2.3.8.3.16.1 Height as required to coordinate with tile selection and setting

system selected.2.3.8.3.17 AGR - Graphite Anodized Aluminum.


2.3.8.3.18 AGSG - Bright Black Anodized Aluminum.2.3.8.3.18.1 Height as required to coordinate with tile selection and setting

system selected.2.3.8.3.19 AGSB - Brushed Black Anodized Aluminum.


2.3.8.3.20 AC - Color-coated Aluminum.2.3.8.3.20.1 BW - Bright White.


2.3.8.3.20.2 W - White.2.3.8.3.20.2.1 Height as required to coordinate with tile selection and

setting system selected.2.3.8.3.20.3 SP - Sand Pebble.


09 30 05-12

2.3.8.3.20.4 BH - Bahama.2.3.8.3.20.4.1 Height as required to coordinate with tile selection and

setting system selected.2.3.8.3.20.5 HB - Light Beige.


2.3.8.3.20.6 HG - Light Grey.2.3.8.3.20.6.1 Height as required to coordinate with tile selection and




setting system selected.2.3.8.3.21 PRO - PVC. Color








setting system selected.2.3.8.3.21.6 HG - Light Grey.


2.3.8.3.21.7 PG - Classic Grey.2.3.8.3.21.7.1 Height as required to coordinate with tile selection and

setting system selected.2.3.8.3.21.8 G - Grey.


2.3.8.3.21.9 GS - Black.2.3.8.3.21.9.1 Height as required to coordinate with tile selection and


2.3.9 Schluter-ECK-E2.3.9.1 Description: roll-formed stainless steel V-shaped profile with 1-15/32 inch (37

mm) wide exposed surfaces joined by a symmetrically rounded corner, with integrated trapezoid-perforated anchoring legs.

2.3.9.2 Profile Angle:2.3.9.2.1 Profile with 90 degree angle.2.3.9.2.2 Profile with 135 degree angle.



2.3.9.3.2 EV4A - Stainless Steel Type 316 L = V4A.

09 30 05-13



system selected.

2.3.10 Schluter-ECK-K2.3.10.1 Description: roll-formed stainless steel V-shaped profile with 1-9/32 inch (32 mm)

or 2 inch (50 mm) wide beveled exposed surfaces joined by a symmetrically rounded corner.

2.3.10.2 Profile Angle:2.3.10.2.1 Profile with 90 degree angle.2.3.10.2.2 Profile with 135 degree angle.


2.3.10.3.1.1 9/16 inch (15 mm).2.3.10.3.1.2 1-9/32 inch (32 mm).2.3.10.3.1.3 2 inch (50 mm).2.3.10.3.1.4 Width as required.

2.3.10.3.2 EV4A - Stainless Steel Type 316 L = V4A.2.3.10.3.2.1 9/16 inch (15 mm).2.3.10.3.2.2 1-9/32 inch (32 mm).2.3.10.3.2.3 2 inch (50 mm).2.3.10.3.2.4 Width as required.

2.3.10.3.3 EB - Brushed Stainless Steel Type 304 = V2A.2.3.10.3.3.1 9/16 inch (15 mm).2.3.10.3.3.2 1-9/32 inch (32 mm).2.3.10.3.3.3 2 inch (50 mm).2.3.10.3.3.4 Width as required.

2.3.11 Schluter-ECK-KI2.3.11.1 Description: Stainless steel inside wall corner profile with 9/16 inch (15 mm) wide

exposed surfaces joined by a symmetrically rounded inside corner with 3/64 inch (1 mm) radius.

2.3.11.2 Corners and Connectors:2.3.11.2.1 Provide with matching inside corners.2.3.11.2.2 Provide with matching outside corners.2.3.11.2.3 Provide with matching connectors.

2.3.11.3 Material and Finish:2.3.11.3.1 E - Stainless Steel Type 304 = V2A.2.3.11.3.2 EV4A - Stainless Steel Type 316 L = V4A.2.3.11.3.3 EB - Brushed Stainless Steel Type 304 = V2A.

2.3.12 Schluter-ECK-KHK2.3.12.1 Description: Stainless steel inside wall corner profile with 9/16 inch (15 mm) wide

exposed surfaces joined by a symmetrically rounded inside corner with 5/16 inch (8 mm) radius.



09 30 05-14

2.3.13 Schluter-RONDEC-DB2.3.13.1 Description: profile with symmetrically rounded 3/8 inch (10 mm) wide, 17/32

inch (14 mm) tall exposed surface, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2.3.13.2 Corners:2.3.13.2.1 Provide with matching outside corners.






2.3.14 Schluter-DESIGNLINE2.3.14.1 Description: U-shaped profile with 1 inch (25 mm) wide exposed surface and 1/4

inch (6 mm) tall integrated vertical anchoring legs on each side.2.3.14.2 Material and Finish:




2.3.14.2.3 MC - Chrome-plated Solid Brass.2.3.14.2.3.1 Height as required to coordinate with tile selection and setting















09 30 05-15



2.3.14.2.14 AMG - Bright Brass Anodized Aluminum.2.3.14.2.14.1 Height as required to coordinate with tile selection and setting

system selected.2.3.14.2.15 AMGB - Brushed Brass Anodized Aluminum.


2.3.15 Schluter-RONDEC-CT2.3.15.1 Description: anodized aluminum, double-rail profile with symmetrically-rounded

exposed surfaces with 1/4 inch (6 mm) radii separated by a 1-1/4 inch (31 mm) wide recessed section with dovetail channels, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.

2.3.15.2 Corners:2.3.15.2.1 Provide with matching inside corners.2.3.15.2.2 Provide with matching outside corners.



2.3.15.3.2 ACGB - Brushed Chrome Anodized Aluminum.2.3.15.3.2.1 Height as required to coordinate with tile selection and setting






2.3.15.3.6 AKGB - Brushed Copper/Bronze Anodized Aluminum.2.3.15.3.6.1 Height as required to coordinate with tile selection and setting




system selected.2.3.15.3.9 TSB - Tuscan Beige Color-coated Aluminum.



system selected.2.3.15.3.11 TSG - Tuscan Pewter Color-coated Aluminum.


2.3.16 Schluter-RONDEC-STEP2.3.16.1 Description: anodized aluminum profile with flat exposed face, symmetrically-

09 30 05-16

rounded exposed top surface with 1/4 inch (6 mm) radius, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.




2.3.16.3.1.2 Length:2.3.16.3.1.2.1 1-3/8 inch (35 mm).2.3.16.3.1.2.2 1-1/2 inch (39 mm).2.3.16.3.1.2.3 2-1/4 inch (57 mm).2.3.16.3.1.2.4 Length as required.


system selected.2.3.16.3.2.2 Length:

2.3.16.3.2.2.1 1-3/8 inch (35 mm).2.3.16.3.2.2.2 1-1/2 inch (39 mm).2.3.16.3.2.2.3 2-1/4 inch (57 mm).2.3.16.3.2.2.4 Length as required.






2.3.16.3.4.2.1 1-3/8 inch (35 mm).2.3.16.3.4.2.2 1-1/2 inch (39 mm).2.3.16.3.4.2.3 Length as required.








system selected.

09 30 05-17

2.3.16.3.7.2 Length:2.3.16.3.7.2.1 1-3/8 inch (35 mm).2.3.16.3.7.2.2 2-1/4 inch (57 mm).2.3.16.3.7.2.3 Length as required.






2.3.16.3.9.2.1 1-1/2 inch (39 mm).2.3.16.3.9.2.2 Length as required.

2.3.17 Schluter-REMA2.3.17.1 Description: wall access panel system featuring aluminum brackets with molded

casings containing magnets that are clamped to lateral, movable guide shoes, and ferromagnetic metal counterplates.

2.4 FINISHING AND EDGE-PROTECTION PROFILES FOR STAIR NOSINGS

2.4.1 Schluter-TREP-E2.4.1.1 Description: roll-formed stainless steel (type 304 = V2A) profile with ribbed, 1-

3/16 inch (30 mm) wide exposed surface with rounded leading edge, and integrated trapezoid-perforated anchoring leg.

2.4.1.2 End Caps: Provide with matching end caps.2.4.1.3 Material and Finish:

2.4.1.3.1 EV4A - Stainless Steel Type 316 L = V4A.2.4.1.3.1.1 Height as required to coordinate with tile selection and setting

system selected.2.4.1.3.2 E - Stainless Steel Type 304 = V2A.


2.4.2 Schluter-TREP-EK2.4.2.1 Description: roll-formed stainless steel (type 304 = V2A) profile with ribbed, 1-

3/16 inch (30 mm) wide exposed surface with rounded leading edge.

2.4.3 Schluter-TREP-G-S2.4.3.1 Description: roll-formed brushed stainless steel (type 304 = V2A) profile with

self-adhesive, non-slip tread, 1-3/16 inch (30 mm) wide exposed surface with rounded leading edge, and integrated trapezoid-perforated anchoring leg.

2.4.3.2 End Caps: Provide with matching end caps.2.4.3.3 Tread Color:

2.4.3.3.1 T - Transparent.2.4.3.3.1.1 Height as required to coordinate with tile selection and setting

system selected.2.4.3.3.2 NB - Nut Brown.


2.4.3.3.3 GS - Black.2.4.3.3.3.1 Height as required to coordinate with tile selection and setting

09 30 05-18

system selected.2.4.3.3.4 CG - Yellow.


2.4.4 Schluter-TREP-G-B2.4.4.1 Description: roll-formed brushed stainless steel (type 304 = V2A) profile with

self-adhesive, non-slip tread, 2-5/32 (55 mm) wide exposed surface with rounded leading edge, and integrated trapezoid-perforated anchoring leg.


2.4.4.3.1 T - Transparent.2.4.4.3.1.1 Height as required to coordinate with tile selection and setting






2.4.5 Schluter-TREP-GK-S2.4.5.1 Description: roll-formed brushed stainless steel (type 304 = V2A) profile with

self-adhesive, non-slip tread, 1-3/16 inch (30 mm) wide exposed surface with rounded leading edge.

2.4.5.2 Tread Color:2.4.5.2.1 T - Transparent.2.4.5.2.2 NB - Nut Brown.2.4.5.2.3 GS - Black.2.4.5.2.4 CG - Yellow.

2.4.6 Schluter-TREP-GK-B2.4.6.1 Description: roll-formed brushed stainless steel (type 304 = V2A) profile with

self-adhesive, non-slip tread, 1-3/16 inch (30 mm) wide exposed surface with rounded leading edge.

2.4.6.2 Tread Color:2.4.6.2.1 T - Transparent.2.4.6.2.2 NB - Nut Brown.2.4.6.2.3 GS - Black.2.4.6.2.4 CG - Yellow.

2.4.7 Schluter-TREP-SE2.4.7.1 Description: Profile with replaceable, ribbed, 1-1/32 inch (26 mm) wide,

thermoplastic rubber exposed surface with rounded leading edge, and roll-formed stainless steel type 304 = V2A support section with integrated trapezoid-perforated anchoring leg.


2.4.7.3.1 HB - Light Beige.2.4.7.3.1.1 Height as required to coordinate with tile selection and setting



09 30 05-19

system selected.2.4.7.3.3 GS - Black.


2.4.7.3.4 G - Grey.2.4.7.3.4.1 Height as required to coordinate with tile selection and setting



2.4.8 Schluter-TREP-S2.4.8.1 Description: Profile with replaceable, ribbed, 1-1/32 inch (26 mm) wide,

thermoplastic rubber exposed surface with rounded leading edge, and aluminum support section with integrated trapezoid-perforated anchoring leg.






system selected.2.4.8.3.4 G - Grey.


2.4.8.3.5 CG - Yellow.2.4.8.3.5.1 Height as required to coordinate with tile selection and setting

system selected.

2.4.9 Schluter-TREP-B2.4.9.1 Description: Profile with replaceable, ribbed, 2-1/16 inch (52 mm) wide,

thermoplastic rubber exposed surface with rounded leading edge, and aluminum support section with integrated trapezoid-perforated anchoring leg.








2.4.9.3.5 CG - Yellow.2.4.9.3.5.1 Height as required to coordinate with tile selection and setting

system selected.

2.4.10 Schluter-TREP-FL

09 30 05-20

2.4.10.1 Description: roll-formed stainless steel (type 304 = V2A) profile, with 11/32 inch (9 mm) -wide, 13/16 inch (21 mm) -tall, exposed surface with rounded leading edge, and integrated trapezoid-perforated anchoring leg.

2.4.10.2 End Caps: Provide with matching end caps.2.4.10.3 Material and Finish:




2.4.11 Schluter-TREP-T2.4.11.1 Description: profile with ribbed, 3/4 inch (19 mm) wide, soft PVC exposed

surface with rounded leading edge, and rigid PVC support section with integrated trapezoid-perforated anchoring leg.


2.4.11.3.1 HB - Light Beige.2.4.11.3.1.1 5/16 inch (8 mm).2.4.11.3.1.2 7/16 inch (11 mm).2.4.11.3.1.3 Height as required to coordinate with tile selection and setting


2.4.11.3.2.1 5/16 inch (8 mm).2.4.11.3.2.2 7/16 inch (11 mm).2.4.11.3.2.3 Height as required to coordinate with tile selection and setting





system selected.

2.4.12 Schluter-TREP-MT2.4.12.1 Description: profile with ribbed, 3/4 inch (19 mm) wide, soft PVC exposed

surface with rounded leading edge and 3/16 inch (5 mm) wide brass inlay (centered on exposed surface), and rigid PVC support section with integrated trapezoid-perforated anchoring leg.







09 30 05-21


2.4.13 Schluter-TREP-TL2.4.13.1 Description: profile with ribbed, 3/4 inch (19 mm) wide, soft PVC exposed

surface with rounded leading edge and 3/16 inch (5 mm) wide luminescent inlay (centered on exposed surface), and rigid PVC support section with integrated trapezoid-perforated anchoring leg.


2.4.13.3.1 SB - Black Brown.2.4.13.3.1.1 Height as required to coordinate with tile selection and setting



2.4.14 Schluter-SCHIENE-STEP2.4.14.1 Description: anodized aluminum T-Shaped profile with 1/8 inch (3 mm) wide top

section and ribbed vertical leg that together for the exposed surface, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.



2.4.14.2.1.2 Vertical Length:2.4.14.2.1.2.1 1-3/16 inch (30 mm).2.4.14.2.1.2.2 1-1/2 inch (39 mm).2.4.14.2.1.2.3 Length as required.

2.4.14.2.2 AT - Brushed Chrome Anodized Aluminum.2.4.14.2.2.1 Height as required to coordinate with tile selection and setting

system selected.2.4.14.2.2.2 Vertical Length:


2.4.15 Schluter-RONDEC-STEP2.4.15.1 Description: anodized aluminum profile with flat exposed face, symmetrically-

rounded exposed top surface with 1/4 inch (6 mm) radius, integrated trapezoid-perforated anchoring leg, and integrated grout joint spacer.




2.4.15.3.1.2 Vertical Length:2.4.15.3.1.2.1 1-3/8 inch (35 mm).2.4.15.3.1.2.2 1-1/2 inch (39 mm).2.4.15.3.1.2.3 2-1/4 inch (57 mm).2.4.15.3.1.2.4 Length as required.


system selected.

09 30 05-22

2.4.15.3.2.2 Vertical Length:2.4.15.3.2.2.1 1-3/8 inch (35 mm).2.4.15.3.2.2.2 1-1/2 inch (39 mm).2.4.15.3.2.2.3 2-1/4 inch (57 mm).2.4.15.3.2.2.4 Length as required.





















2.4.15.3.9.2.1 1-1/2 inch (39 mm).2.4.15.3.9.2.2 Length as required.

09 30 05-23

2.5 MOVEMENT JOINTS AND COVE-SHAPED PROFILES

2.5.1 Schluter-DILEX-BWS2.5.1.1 Description: profile with integrated rigid, recycled PVC, trapezoid-perforated

anchoring legs, connected by a 3/16 inch (5 mm) wide soft CPE movement zone that forms the visible surface.

2.5.1.2 Movement Zone Color:2.5.1.2.1 BW - Bright White.


2.5.1.2.2 SP - Sand Pebble.2.5.1.2.2.1 Height as required to coordinate with tile selection and setting

system selected.2.5.1.2.3 HB - Light Beige.



system selected.2.5.1.2.5 PG - Classic Grey.



system selected.

2.5.2 Schluter-DILEX-BWB2.5.2.1 Description: profile with integrated rigid, recycled PVC, trapezoid-perforated

anchoring legs, connected by a 3/8 inch (10 mm) wide soft CPE movement zone that forms the visible surface.










system selected.

2.5.3 Schluter-DILEX-AKWS2.5.3.1 Description: profile with integrated aluminum, trapezoid-perforated anchoring

legs, connected by grip bars to a 1/4 inch (6 mm) wide soft PVC movement zone, which together form the visible surface.

2.5.3.2 Movement Zone Color:2.5.3.2.1 SP - Sand Pebble.

09 30 05-24





2.5.3.2.4 PG - Classic Grey.2.5.3.2.4.1 Height as required to coordinate with tile selection and setting



2.5.4 Schluter-DILEX-EDP2.5.4.1 Description: stainless steel profile with integrated trapezoid-perforated anchoring

legs connected by a 15/32 inch (12 mm) wide tongue-and-groove joint that forms the visible surface.



2.5.5 Schluter-DILEX-KSN2.5.5.1 Description: profile with integrated trapezoid-perforated anchoring legs,

connected by a 7/16 inch (11 mm) wide replaceable thermoplastic rubber movement zone, which together form the visible surface.

2.5.5.2 Anchoring Legs Material:2.5.5.2.1 E - Stainless Steel Type 304 = V2A.






system selected.2.5.5.3 Movement Zone Color:

2.5.5.3.1 SP - Sand Pebble.2.5.5.3.2 HB - Light Beige.2.5.5.3.3 GS - Black.2.5.5.3.4 PG - Classic Grey.2.5.5.3.5 G - Grey.

2.5.6 Schluter-DILEX-EKSB2.5.6.1 Description: profile with integrated roll-formed stainless steel with trapezoid-

perforated anchoring legs, connected by a 1/4 inch (6 mm) wide thermoplastic rubber movement zone, which together form the visible surface.



09 30 05-25



2.5.6.3.1 HB - Light Beige.2.5.6.3.2 GS - Black.2.5.6.3.3 PG - Classic Grey.2.5.6.3.4 G - Grey.

2.5.7 Schluter-DILEX-KSBT2.5.7.1 Description: profile with integrated trapezoid-perforated anchoring legs,

connected by a replaceable thermoplastic rubber movement zone, which together form the visible surface.

2.5.7.2 Anchoring Legs Material:2.5.7.2.1 EV4A - Stainless Steel Type 304 = V2A.






system selected.2.5.7.3 Movement Color:

2.5.7.3.1 HB - Light Beige.2.5.7.3.2 GS - Black.2.5.7.3.3 G - Grey.

2.5.7.4 Movement Zone Width:2.5.7.4.1 3/4 inch (20 mm).

2.5.8 Schluter-DILEX-EZ2.5.8.1 Description: Profile with textured, concave, rigid PVC side walls connected on

top and bottom by 9/32 inch (7 mm) wide soft PVC movement zones that form the visible surface.

2.5.8.2 Movement Color:2.5.8.2.1 M/G - Brass Inlay/Grey.


2.5.8.2.2 C/CG - Chrome Inlay/Yellow.2.5.8.2.2.1 Height as required to coordinate with tile selection and setting

system selected.

2.5.9 Schluter-DILEX-BT2.5.9.1 Description: Extruded satin anodized aluminum profile with integrated trapezoid-

perforated anchoring legs, connected by a 1-3/16 inch (30 mm) wide sliding telescopic center section with two interconnected ball-and-socket joints, which together form the visible surface.

2.5.9.2 Profile Height2.5.9.2.1 Height as required to coordinate with tile selection and setting system

selected.

2.5.10 Schluter-DILEX-BT/O2.5.10.1 Description: Extruded satin anodized aluminum profile with integrated trapezoid-

09 30 05-26

perforated anchoring legs, connected at a 90-degree angle by a 1-3/16 inch (30 mm) wide sliding telescopic center section with two interconnected ball-and-socket joints, which together form the visible surface.

2.5.10.2 Profile Height:2.5.10.2.1 Height as required to coordinate with tile selection and setting system

selected.

2.5.11 Schluter-DILEX-BTS2.5.11.1 Description: Extruded satin anodized aluminum profile with 3/8 inch (10 mm) tall

integrated anchoring legs, connected by a 1-3/16 inch (30 mm) wide sliding telescopic center section with two interconnected ball-and-socket joints, which together form the visible surface.

2.5.12 Schluter-DILEX-MOP2.5.12.1 Description: profile with serrated rigid, recycled PVC side sections connected by

a soft PVC central movement zone, which form the 5/16 inch (8 mm) wide visible surface.

2.5.12.2 Size:2.5.12.2.1 Height as required to coordinate with tile selection and setting system

selected.

2.5.13 Schluter-DILEX-MP2.5.13.1 Description: profile with dovetailed, rigid, recycled PVC side sections overlapped

and connected by a 5/16 inch (8 mm) wide soft CPE central movement zone that forms the visible surface.

2.5.13.2 Color:2.5.13.2.1 HB - Light Beige.

2.5.13.2.1.1 1-3/8 inch (35 mm).2.5.13.2.2 ZR - Brick Red.

2.5.13.2.2.1 1-3/8 inch (35 mm).2.5.13.2.3 GS - Black.

2.5.13.2.3.1 1-3/8 inch (35 mm).2.5.13.2.4 G - Grey.

2.5.13.2.4.1 1-3/8 inch (35 mm).2.5.13.3 Size: Height as required.

2.5.14 Schluter-DILEX-MPV2.5.14.1 Description: profile extension for Schluter-DILEX-MP with rigid, recycled PVC

side sections and interlocking top and bottom cross-sections.2.5.14.2 Size:

2.5.14.2.1 Height: 9/16 inch (15 mm).2.5.14.2.2 Height: 1 inch (25 mm).2.5.14.2.3 Height as required.

2.5.15 Schluter-DILEX-AS2.5.15.1 Description: profile with integrated rigid PVC trapezoid-perforated anchoring leg

and a sloped flexible joining leg, with self-adhesive tape on the underside, which forms the visible surface.

2.5.15.2 Corners:2.5.15.2.1 Provide with matching inside corners.2.5.15.2.2 Provide with matching end caps.

2.5.15.3 Color:2.5.15.3.1 BW - Bright White.

2.5.15.3.1.1 3/8 inch (10 mm).

2.5.16 Schluter-DILEX-BWA2.5.16.1 Description: profile with integrated rigid, recycled PVC trapezoid-perforated

09 30 05-27

anchoring leg and dovetailed channel, which are connected by a 3/16 inch (5 mm) wide soft CPE movement zone that forms the visible surface, and a slit lower movement zone of soft CPE.

2.5.16.2 Color:2.5.16.2.1 BW - Bright White.



system selected.2.5.16.2.3 SP - Sand Pebble.






system selected.

2.5.17 Schluter-DILEX-KSA2.5.17.1 Description: profile with integrated trapezoid-perforated anchoring leg and 3/8

inch (10 mm) wide replaceable thermoplastic rubber movement zone with self-adhesive backing strip, which together form the visible surface.




system selected.2.5.17.2.3 A - Aluminum.


2.5.17.3 Movement Color:2.5.17.3.1 HB - Light Beige.2.5.17.3.2 GS - Black.2.5.17.3.3 G - Grey.2.5.17.3.4 PG - Light Grey.

2.5.18 Schluter-DILEX-EKE2.5.18.1 Description: profile with integrated rigid, recycled PVC trapezoid-perforated

anchoring legs, connected at a 90-degree angle by a 3/16 inch (5 mm) wide soft CPE movement zone that forms the visible surface.






09 30 05-28



2.5.18.2.5 PG - Classic Grey.2.5.18.2.5.1 Height as required to coordinate with tile selection and setting



2.5.19 Schluter-DILEX-HKW2.5.19.1 Description: profile with rigid, recycled PVC integrated trapezoid-perforated

anchoring legs, connected at a 90-degree angle by a rigid PVC cove-shaped section with 11/16 inch (18 mm) radius that forms the visible surface.

2.5.19.2 Corners:2.5.19.2.1 Provide with matching inside corners.2.5.19.2.2 Provide with matching outside corners.2.5.19.2.3 Provide with matching end caps.2.5.19.2.4 Provide with matching connectors.

2.5.19.3 Cove Section Color:2.5.19.3.1 BW - Bright White.






system selected.

2.5.20 Schluter-DILEX-HK2.5.20.1 Description: profile with integrated rigid, recycled PVC trapezoid-perforated

anchoring legs, connected at a 90-degree angle by a soft CPE cove-shaped section with 11/16 inch (18 mm) radius that forms the visible surface.


2.5.20.3 Cove Section Color:2.5.20.3.1 BW - Bright White.





2.5.21 Schluter-DILEX-AHK2.5.21.1 Description: anodized aluminum profile with integrated trapezoid-perforated

09 30 05-29

anchoring legs, connected at a 90-degree angle by a cove-shaped section with 3/8 inch (10 mm) radius that forms the visible surface.










2.5.21.3.6 ATGB - Polished Brushed Nickel Anodized Aluminum.2.5.21.3.6.1 Height as required to coordinate with tile selection and setting







system selected.2.5.21.3.11 AMG - Polished Brass Anodized Aluminum.



system selected.2.5.21.3.13 AGRB - Brushed Graphite Anodized Aluminum.


2.5.22 Schluter-DILEX-PHK2.5.22.1 Description: Pre-colored rigid PVC profile with integrated trapezoid-perforated

anchoring legs, connected at a 90-degree angle by a cove-shaped section with 3/8 inch (10 mm) radius that forms the visible surface.

2.5.22.2 Corners:2.5.22.2.1 Provide with matching inside corners.2.5.22.2.2 Provide with matching outside corners.2.5.22.2.3 Provide with matching end caps.

09 30 05-30

2.5.22.2.4 Provide with matching connectors.2.5.22.3 Finish and Height:












2.5.23 Schluter-DILEX-AHKA2.5.23.1 Description: Anodized aluminum profile with single integrated trapezoid-

perforated anchoring leg and dovetailed channel, connected at a 90 degree angle by a cove-shaped 3/8 inch (10 mm) radius section that forms the visible surface.







2.5.23.3.4 ATGB - Polished Brushed Nickel Anodized Aluminum.2.5.23.3.4.1 Height as required to coordinate with tile selection and setting

system selected.

2.5.24 Schluter-DILEX-EHK2.5.24.1 Description: roll-formed stainless steel profile with integrated trapezoid-

perforated anchoring legs, connected at a 90-degree angle by a cove-shaped section with 23/32 inch (18.5 mm) radius that forms the visible surface.


09 30 05-31






2.5.25 Schluter-DILEX-HKU2.5.25.1 Description: roll-formed stainless steel cove-shaped profile with 3/8 inch (10 mm)

radius that forms the visible surface and an internal integrated trapezoid-perforated anchoring leg .



2.5.26 Schluter-DILEX-HKS2.5.26.1 Description: profile with integrated, roll-formed stainless steel with trapezoid-

perforated anchoring legs, connected at a 90-degree angle by a stainless steel cove-shaped section with 23/32 inch (18.5 mm) radius and 1/2 inch (12.5 mm) wide thermoplastic rubber movement zone, which together form the visible surface.






2.5.26.4.1 HB - Light Beige.2.5.26.4.2 GS - Black.2.5.26.4.3 PG - Classic Grey.2.5.26.4.4 G - Grey.

2.6 MODULAR SCREED SYSTEM

2.6.1 Schluter-BEKOTEC Polyethylene Foil:2.6.1.1 Modular Screed System: Schluter-BEKOTEC 36 inch by 47-1/4 inch (90 cm by

120 cm) polyethylene panel, with 7/8 inch (23 mm) high integrated studs set in a grid pattern spaced 4-1/4 inch (108 mm) on center.

2.6.1.1.1 Provide with matching edge strip.

09 30 05-32

2.6.2 Schluter-BEKOTEC-DRAIN Polyethylene Foil:2.6.2.1 Modular Screed System: Schluter-BEKOTEC 36 inch by 47-1/4 inch (90 cm by

120 cm) polyethylene panel, with evenly spaced openings and interconnected drainage channels, with 7/8 inch (23 mm) high integrated studs set in a grid pattern spaced 4-1/4 inch (108 mm) on center.


2.6.3 Schluter-BEKOTEC Expanded Polystyrene:2.6.3.1 Description: 24 inch by 48 inch by 1-3/8 inch (610 mm by 1219 mm by 35 mm)

expanded polystyrene panel, with 15/16 inch (24 mm) high integrated studs set in a grid pattern spaced 4-1/4 inch (108 mm) on center.


2.7 UNCOUPLING MEMBRANE

2.7.1 Schluter-DITRA2.7.1.1 Description: 1/8 inch (3 mm) thick, orange, high-density polyethylene membrane

with a grid structure of 1/2 inch by 1/2 inch (12 mm by 12 mm) square cavities, each cut back in a dovetail configuration, and a polypropylene anchoring fleece laminated to its underside. Conforms to definition for uncoupling membranes in the Tile Council of North America Handbook for Ceramic Tile Installation and is listed by cUPC to meet or exceed the requirements of the "American national standard specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation A118.10 and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467).

2.7.1.2 Waterproofing seaming membrane:2.7.1.2.1 Provide KERDI BAND Seams and Corners material 0.004 inch (0.1 mm)

thick, orange polyethylene membrane, with polypropylene fleece laminated on both sides.

2.7.2 Schluter-DITRA-XL2.7.2.1 Description: 9/32 inch (7 mm) thick, orange, high-density polyethylene

membrane with a grid structure of 1/2 inch by 1/2 inch (12 mm by 12 mm) square cavities, each cut back in a dovetail configuration, and a polypropylene anchoring fleece laminated to its underside. Conforms to definition for uncoupling membranes in the Tile Council of North America Handbook for Ceramic Tile Installation and listed by cUPC to meet or exceed the requirements of the "American national standard specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation A118.10 and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467).



2.7.3 Schluter-DITRA-HEAT2.7.3.1 Description: 1/4 inch (5.5 mm) thick, orange, high-density polypropylene

membrane with a cut-back stud structure, specifically designed to secure Schluter DITRA HEAT electric heating cables in place. An anchoring fleece is laminated to its underside. The membrane conforms to the definition for uncoupling membranes in the Tile Council of North America Handbook for Ceramic Tile Installation.

2.7.3.2 Thermostat:2.7.3.2.1 Programmable2.7.3.2.2 Non-Programmable.

2.7.3.3 Heating Cable Voltage:

09 30 05-33

2.7.3.3.1 120V.2.7.3.3.2 240V.

2.7.3.4 Heating Cable:2.7.3.4.1 Heating cable placement as detailed.



2.7.4 Schluter-DITRA-DRAIN2.7.4.1 Description: 5/32 inch (4 mm) thick, Drainage membrane designed for use with

thin bed ceramic and stone tile assemblies in exterior applications. Membrane consists of orange, high-density studded polyethylene sheet with laminated polypropylene filter fabric to the upper side.

2.8 WATERPROOFING MEMBRANE

2.8.1 Schluter-KERDI2.8.1.1 Description: 0.008 inch (0.2 mm) thick, orange polyethylene membrane, with

polypropylene fleece laminated on both sides, which is listed by cUPC to meet or exceed requirements of the "American national standard specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation A118.10 and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467).

2.8.1.2 Corners and seals:2.8.1.2.1 Provide matching preformed inside corners.2.8.1.2.2 Provide matching preformed outside corners.2.8.1.2.3 Provide matching preformed pipe seals.2.8.1.2.4 Provide matching preformed mixing valve seals.

2.8.2 Schluter-KERDI-DS2.8.2.1 Description: 0.020 inch (20. mils) thick, orange polyethylene membrane, with

polypropylene fleece laminated on both sides.2.8.2.2 Corners and seals:

2.8.2.2.1 Provide matching preformed inside corners.2.8.2.2.2 Provide matching preformed outside corners.2.8.2.2.3 Provide matching preformed pipe seals.2.8.2.2.4 Provide matching preformed mixing valve seals.

2.8.3 Schluter-KERDI-BAND2.8.3.1 Description: Seams and Corners material 0.004 inch (0.1 mm) thick, orange

polyethylene membrane, with polypropylene fleece laminated on both sides.2.8.3.2 Width:

2.8.3.2.1 Width as required.

2.9 FLOOR DRAIN WITH INTEGRATED BONDING FLANGE

2.9.1 Schluter-KERDI-DRAIN, Plastic:2.9.1.1 Description: floor drain 11-25/32 inch (300 mm) diameter, trapezoid-perforated,

integrated bonding flange with polypropylene fleece thermally laminated to the surface and hubbed connection to 2 inch (50 mm) drain pipe. Grate assembly includes 4 inch by 4 inch (102 mm by 102 mm) square grate, height adjustment collar, and lateral adjustment ring with trapezoid perforations.

2.9.1.2 Drain listed by UPC to meet requirements of "International Association of Plumbing and Mechanical Officials Interim Guide Criteria for Floor Drain with Integrated Bonding Flange" (IGC 195), listed by CSA to meet requirements of the Canadian Standards Association standard, "Floor, Area, and Shower Drains,

09 30 05-34

and Cleanouts for Residential Construction" (CSA B79), and referenced in method B422 of the Tile Council of North America Handbook for Ceramic Tile Installation.

2.9.1.3 Drain Housing Material:2.9.1.3.1 ABS.2.9.1.3.2 PVC.

2.9.1.4 Grate Material and Finish:2.9.1.4.1 E - Stainless Steel Type 304 = V2A.2.9.1.4.2 EOB - Oil-Rubbed Bronze Stainless Steel Type 304 = V2A.2.9.1.4.3 ECS - Tileable covering support stainless steel type 304.2.9.1.4.4 ATGB - Brushed Nickel Anodized Aluminum.2.9.1.4.5 AKGB - Brushed Copper/Bronze Anodized Aluminum.2.9.1.4.6 AMGB - Brushed Brass Anodized Aluminum.

2.9.1.5 Nominal Grate Size:2.9.1.5.1 4 inch (100 mm) by 4 inch (100 mm) square.2.9.1.5.2 6 inch (150 mm) by 6 inch (150 mm) square.2.9.1.5.3 6 inch (150 mm) round.

2.9.1.6 Drain Outlet:2.9.1.6.1 2 inch (50 mm) outlet.2.9.1.6.2 3 inch (75 mm) outlet.

2.9.2 Schluter-KERDI-DRAIN, Stainless Steel:2.9.2.1 Description: stainless steel floor drain 9-27/32 inch (250 mm) diameter integrated

bonding flange with 3 inch (75 mm) no-hub outlet, and grate assembly. Grate assembly includes stainless steel grate, height adjustment collar, and lateral adjustment ring with trapezoid perforations.

2.9.2.2 Drain listed by UPC to meet requirements of "International Association of Plumbing and Mechanical Officials Interim Guide Criteria for Floor Drain with Integrated Bonding Flange" (IGC 195), listed by CSA to meet requirements of the Canadian Standards Association standard, "Floor, Area, and Shower Drains, and Cleanouts for Residential Construction" (CSA B79), Drain detail as referenced in method B422 of the Tile Council of North America Handbook for Ceramic Tile Installation.

2.9.2.3 Drain Housing Material:2.9.2.3.1 Stainless Steel.



2.9.2.6 Drain Outlet:2.9.2.6.1 2 inch (50 mm) outlet.2.9.2.6.2 2 inch Threaded stainless steel (50 mm) outlet.2.9.2.6.3 3 inch (75 mm) outlet.

2.9.3 Schluter-KERDI-DRAIN ADAPTER KIT, Plastic:2.9.3.1 Description:

2.9.3.1.1 Floor drain adaptor kit consisting of stainless steel adaptor ring with over-molded santoprene gasket, 11-13/16 inch (300 mm) diameter sloped integrated bonding flange with thermally laminated polypropylene fleece,

09 30 05-35

and grate assembly. Grate assembly includes grate, height adjustment collar, and lateral adjustment ring with trapezoid perforations. Drain detail as referenced in method B422 of the Tile Council of North America Handbook for Ceramic Tile Installation.

2.9.3.1.2 Drain type as referenced in methods B422 and B422 STONE in the Tile Council of North America Handbook for Ceramic, Glass, and Stone Tile Installation.

2.9.3.2 Drain Housing Material:2.9.3.2.1 ABS.2.9.3.2.2 PVC.



2.9.3.5 Bonding Flange Length:2.9.3.5.1 1-9/16 inch (39.7 mm).2.9.3.5.2 3-41/64 inch (92.4 mm).

2.9.4 Schluter Schluter-KERDI-DRAIN ADAPTER, Stainless Steel:2.9.4.1 Description:

2.9.4.1.1 Floor drain adaptor kit consisting of stainless steel adaptor ring with over-molded santoprene gasket, 9.843 inch (250 mm) diameter sloped integrated bonding flange, and grate assembly. Grate assembly includes stainless steel grate, height adjustment collar, and lateral adjustment ring with trapezoid perforations.

2.9.4.1.2 Drain detail as referenced in method B 422 of the Tile Council of North America Handbook for Ceramic Tile Installation.

2.9.4.2 Drain Housing Material:2.9.4.2.1 Stainless Steel.



2.9.5 Schluter-KERDI-LINE DRAIN, Brushed Stainless Steel:2.9.5.1 Description:

2.9.5.1.1 Linear floor drain consisting of a formed stainless steel channel body and grate assembly that can be seamlessly adjusted to tile or stone covering thickness from 1/8 inch (3 mm) to 1 inch (25 mm). The channel body features a 2-1/4 inch (57 mm) wide trough, a 2 inch (50 mm) no-hub outlet and a 7/8 inch (22 mm) wide bonding flange laminated with a collar made of the Schluter-KERDI waterproofing membrane. The grate assembly

09 30 05-36

includes a 3/8 inch (10 mm) wide brushed stainless steel grate frame and 2-1/8 inch (54 mm) wide grate insert that together form the visible surface. Drain type as referenced in methods B422 and B422 STONE in the Tile Council of North America Handbook for Ceramic, Glass, and Stone Tile Installation.

2.9.5.2 Channel Body Material:2.9.5.2.1 Stainless Steel 304 (1.4301 = V2A).

2.9.5.3 Channel Body and Grate Nominal Length:2.9.5.3.1 20 inch (500 mm).2.9.5.3.2 24 inch (600 mm).2.9.5.3.3 28 inch (700 mm)2.9.5.3.4 32 inch (800 mm).2.9.5.3.5 36 inch (900 mm).2.9.5.3.6 40 inch (1000 mm).2.9.5.3.7 44 inch (1100 mm).2.9.5.3.8 48 inch (1200 mm).2.9.5.3.9 52 inch (130 cm).2.9.5.3.10 56 inch (140 cm).2.9.5.3.11 60 inch (150 cm).2.9.5.3.12 64 inch (160 cm).2.9.5.3.13 68 inch (170 cm).2.9.5.3.14 72 inch (180 cm).

2.9.5.4 Grate Frame Height:2.9.5.4.1 3/4 inch (19 mm).2.9.5.4.2 1-1/8 inch (30 mm).2.9.5.4.3 Not required for Frameless Tilable Grate.2.9.5.4.4 Height as required to coordinate with tile selection and setting system

selected.2.9.5.5 Grate Design:

2.9.5.5.1 Closed-design, brushed stainless steel 304 (1.4301 = V2A) grate.2.9.5.5.2 Brushed stainless steel 304 (1.4301 = V2A) grate with square perforations

and locking mechanism.2.9.5.5.3 Frameless Tileable plate stainless steel type 304.

2.9.5.6 Drain Outlet:2.9.5.6.1 Center.2.9.5.6.2 Off-set.

2.9.5.7 Drain Grate Connector Plate:2.9.5.7.1 Brushed stainless steel 304 (1.4301 = V2A).

2.10 PREFABRICATED SHOWER COMPONENTS

2.10.1 Schluter-KERDI-SHOWER-ST2.10.1.1 Description: trapezoid-imprinted, prefabricated, sloped tiled shower tray base,

made of 2.75 lb/ft3 (44 kg/m3) density, self-extinguishing (HF-1 rating per UL-94) expanded polystyrene, with 12-5/16 inch (313 mm) diameter removable recessed section with 1/8 inch (3 mm) wide ribs on top and channels on the underside.

2.10.1.2 Size:2.10.1.2.1 ST-122 - 48 inch by 48 inch by 1-1/2 inch (1220 mm by 1220 mm by 38

mm).2.10.1.2.2 ST-81/152 - 32 inch by 60 inch by 1-3/4 inch (810 mm by 1520 mm by

44mm).2.10.1.2.3 ST-81/152 BR - 32 inch by 60 inch by 1-1/2 inch (810 mm by 1520 by 38

mm).2.10.1.2.4 ST-183 - 72 inch by 72 inch by 1-1/2 inch (1830 mm by 1830 mm by 38

mm).

09 30 05-37

2.10.2 Schluter-KERDI-SHOWER-L/-LS2.10.2.1 Description: trapezoid-imprinted, prefabricated, sloped tiled shower tray base,

made of 2.75 lb/ft3 (44 kg/m3) density, self-extinguishing (HF-1 rating per UL-94) expanded polystyrene, with removable recessed section and bonded Schluter KERDI Membrane 0.008 inch (0.2 mm) thick, which meet or exceed the requirements of the American national standard specifications for load bearing, bonded, waterproof membranes for thin-set ceramic tile and dimension stone installation A118.10, and is listed by cUPC, and is evaluated by ICC-ES (see Report No. ESR-2467). Meeting ANSI A118.10 as detail as referenced in method B422 of the Tile Council of North America Handbook for Ceramic Tile Installation.

2.10.2.2 Tray for Wall or Entrance Placement:2.10.2.2.1 KSL1000S - 39 inch by 39 inch by 1-21/32 inch (100 cm by 100 cm by 42

mm).2.10.2.2.2 KSL1400S - 55 inch by 55 inch by 2 inch (140 cm by 140 cm by 50 mm).

2.10.2.3 Tray for Floor Center Drain Placement:2.10.2.3.1 KSL1000 - 39 inch by 39 inch by 1-1/4 inch (100 cm by 100 cm vy 32 mm).2.10.2.3.2 KSL1400 - 55 inch by 55 inch by 2 inch (140 cm by 140 cm by 36 mm).

2.10.3 Schluter-KERDI-SHOWER-SC2.10.3.1 Description: trapezoid-imprinted, prefabricated, tiled shower curb base, made of

2.75 lb/ft3 (44 kg/m3) density, self-extinguishing (HF-1 rating per UL-94) expanded polystyrene.

2.10.3.2 Curb dimensions are 48 inch by 6 inch by 4-1/2 inch (1220 mm by 150 mm by 115 mm).

2.10.4 Schluter-KERDI-SHOWER-SR2.10.4.1 Description: trapezoid-imprinted, prefabricated, tiled shower ramp base, made of

2.75 lb/ft3 (44 kg/m3) density, self-extinguishing (HF-1 rating per UL-94) expanded polystyrene.

2.10.4.2 Ramp dimensions are 48 inch by 15-7/8 inch (1220 mm by 40 mm) with slope from maximum thickness of 1-1/2 inch (38 mm) to minimum thickness of 1/4 inch (6 mm).

2.10.5 Schluter-KERDI-SHOWER-SB2.10.5.1 Description: trapezoid-imprinted, prefabricated, tiled shower bench, made of 2.75

lb/ft3 (44 kg/m3) density, self-extinguishing (HF-1 rating per UL-94) expanded polystyrene, with 1/8 inch (3 mm) wide ribs on top and channels on the underside.

2.10.5.2 Size:2.10.5.2.1 SB41 - 16 inch by 16 inch by 20 inch (41 cm by 41 cm by 51 cm).2.10.5.2.2 SB2981 - 32 inch by 11-1/2 inch by 20 inch (81 cm by 29 cm by 51 cm).2.10.5.2.3 SB29107 - 42 inch by 11-1/2 inch by 20 inch (107 cm by 29 cm by 51 cm).2.10.5.2.4 SB29122 - 48 inch by 11-1/2 inch by 20 inch (122 cm by 29 cm by 51 cm).2.10.5.2.5 SB4181 - 32 inch by 16 inch by 20 inch (81 cm by 41 cm by 51 cm).2.10.5.2.6 SB41122 - 48 inch by 16 inch by 20 inch (122 cm by 41 cm by 51 cm).

2.10.6 Schluter-KERDI-BOARD-SN2.10.6.1 Description: Prefabricated waterproof niche, constructed of rigid extruded

polystyrene foam building element panel, with reinforcement material and polypropylene fleece webbing laminated on both sides for thin-set ceramic tile and dimension stone Installations.

2.10.6.2 Size:2.10.6.2.1 KB 12 SN 305 152 A - 12 inches by 6 inches by 3 inches (30 cm by 15 cm

by 7.5 cm).2.10.6.2.2 KB 12 SN 305 305 A - 12 inches by 12 inches by 3 inches (30 cm by 30

09 30 05-38

cm by 7.5 cm).2.10.6.2.3 KB 12 SN 305 508 A1 - 12 inches by 20 inches by 3 inches (30 cm by 51

cm by 7.5 cm).2.10.6.2.4 KB 12 SN 305 711 A1 - 12 inches by 28 inches by 3 inches (30 cm by 71

cm by 7.5 cm).

2.10.7 Schluter-KERDI-FIX2.10.7.1 Description: single-component, elastomeric, waterproof sealing and bonding

compound with a silane-modified polymer base. Compound is free of solvents and odorless.

2.10.7.2 Color:2.10.7.2.1 BW - Bright White.2.10.7.2.2 G - Grey.

2.11 WATERPROOF BUILDING PANEL FOR CERAMIC AND STONE TILE

2.11.1 Schluter-KERDI-BOARD2.11.1.1 Description: Rigid extruded polystyrene foam building element panel, with

reinforcement material and polypropylene fleece webbing laminated on both sides for thin-set ceramic tile and dimension stone Installations.

2.11.1.2 Panel Thickness:2.11.1.2.1 Thickness as required.

2.11.1.3 Panel Size:2.11.1.3.1 48 inch by 64 inch (122 by 162.5 cm).2.11.1.3.2 48 inch by 96 inch (122 by 244 cm).2.11.1.3.3 24-1/2 inch by 96 inch (62.5 by 244 cm).

2.12 DRAINAGE MEMBRANES

2.12.1 Schluter-TROBA2.12.1.1 Description: orange polyethylene sheet with 3/32 inch (7 mm) tall trapezoid-

shaped perforated studs that form vault-like cavities.

2.12.2 Schluter-TROBA-PLUS2.12.2.1 Description: orange polyethylene sheet with 5/16 inch (8 mm) high, truncated

cone-shaped studs, covered with a polypropylene water-permeable filter fabric.

2.13 FINISHING AND TRANSITION PROFILES FOR SHOWERS

2.13.1 Schluter-SHOWERPROFILE-S2.13.1.1 Description: two-part profile with an exposed brushed stainless steel tapered

edge and recycled PVC support section with integrated trapezoid-perforated anchoring leg for lateral transitions between sloped shower floors and walls.

2.13.1.2 Profile Height:2.13.1.2.1 Height as required to coordinate with tile selection and tile setting system

selected.2.13.1.3 Profile Length:

2.13.1.3.1 Length as required.

2.13.2 Schluter-SHOWERPROFILE-R2.13.2.1 Description: two-part profile with an adjustable brushed stainless steel exposed

surface for transitions between the tiled floors and the KERDI-LINE Drain.2.13.2.2 Profile Height:

2.13.2.2.1 Height as required.2.13.2.3 Profile Length:

2.13.2.3.1 Length as required.

09 30 05-39

2.13.3 Schluter-SHOWERPROFILE-WS2.13.3.1 Description: two-part splashguard profile with a 3/4 inch (19 mm) wide anodized

aluminum support section and PVC insert that together form the visible surface between the tiled floors and walls.

2.13.3.2 Splashguard Insert:2.13.3.2.1 Semi-circular Lip.2.13.3.2.2 Collapsible Straight Lip.

2.13.4 Schluter-SHOWERPROFILE-WSK2.13.4.1 Description: two-part splashguard profile with a 2-1/6 inch (52 mm) wide 5/16

inch (8 mm) tall anodized aluminum support section and PVC insert that together form the visible surface.

2.13.4.2 Splashguard Insert:2.13.4.2.1 Semi-circular Lip.2.13.4.2.2 Collapsible Straight Lip.

2.13.5 Schluter-DECO-SG2.13.5.1 Description: anodized aluminum support channel with 1/8 inch (3 mm) wide

vertical side sections and 1/2 inch (12 mm) wide channel for shower glass walls and partitions. Profile includes a integrated trapezoid perforated anchoring leg.


2.13.5.2.1.1 Height as required to coordinate with tile selection and tile setting system selected.

2.13.5.2.2 ACG - Polished Chrome Anodized Aluminum.2.13.5.2.2.1 Height as required to coordinate with tile selection and tile setting

system selected.

2.14 FINISHING AND EDGE-PROTECTION PROFILES AND GUTTERS FOR BALCONIES AND TERRACES

2.14.1 Schluter-BARA-ESOT2.14.1.1 Description: stainless steel type 304 = V2A, L-shaped profile with a trapezoid-

perforated anchoring leg and circle-perforated vertical section.2.14.1.2 Height:

2.14.1.2.1 2-3/8 inch (60 mm).2.14.1.2.2 4-3/8 inch (110 mm).2.14.1.2.3 Height as required.

2.14.2 Schluter-BARA-RW2.14.2.1 Description: L-shaped profile with a 3-1/2 inch (90 mm) wide integrated

trapezoid-perforated anchoring leg.2.14.2.1.1 Provide with straight anchoring leg.2.14.2.1.2 Provide with special radius anchoring leg for radius applications.2.14.2.1.3 Provide with matching connector.


2.14.2.2.1.1 Height as required.2.14.2.2.2 AC - Color-coated Aluminum.

2.14.2.2.2.1 BW - Bright White.2.14.2.2.2.1.1 Height as required.

2.14.2.2.2.2 HB - Light Beige.2.14.2.2.2.2.1 Height as required.

2.14.2.2.2.3 RB - Red Brown.2.14.2.2.2.3.1 Height as required.

2.14.2.2.2.4 SB - Black Brown.2.14.2.2.2.4.1 Height as required.

09 30 05-40

2.14.2.2.2.5 PG - Classic Grey.2.14.2.2.2.5.1 Height as required.

2.14.2.2.2.6 GM - Metallic Grey.2.14.2.2.2.6.1 Height as required.

2.14.3 Schluter-BARA-RWL2.14.3.1 Description: L-shaped profile with a 3-1/2 inch (90 mm) wide integrated

trapezoid-perforated anchoring leg and weep holes spaced at 2-15/16 inch (75 mm), that forms the visible surface.

2.14.3.2 Anchoring Leg:2.14.3.2.1 Provide with straight anchoring leg.2.14.3.2.2 Provide with special radius anchoring leg for radius applications.2.14.3.2.3 Provide with matching connector.

2.14.3.3 Material and Finish:2.14.3.3.1 AC - Color-coated Aluminum.

2.14.3.3.1.1 PG - Classic Grey.2.14.3.3.1.1.1 Height as required.

2.14.3.3.1.2 GM - Metallic Grey.2.14.3.3.1.2.1 Height as required.

2.14.4 Schluter-BARA-RK2.14.4.1 Description: color-coated aluminum, T-shaped profile with a 3-1/8 inch (80 mm)

wide integrated trapezoid-perforated anchoring leg, 1-9/16 inch (40 mm) tall vertical section, and 1-1/16 inch (25 mm) tall drip lip with 3/4 inch (20 mm) offset. Total height of visible surface is 2-5/8 inch (65 mm).

2.14.4.2 Corners:2.14.4.2.1 Provide with matching inside corners.2.14.4.2.2 Provide with matching outside corners.2.14.4.2.3 Provide with matching connector.

2.14.4.3 Color:2.14.4.3.1 BW - Bright White.2.14.4.3.2 HB - Light Beige.2.14.4.3.3 RB - Red Brown.2.14.4.3.4 SB - Black Brown.2.14.4.3.5 PG - Classic Grey.2.14.4.3.6 GM - Metallic Grey.

2.14.5 Schluter-BARA-RAK2.14.5.1 Description: color-coated aluminum profile with a 3-1/8 inch (80 mm) wide

integrated trapezoid-perforated anchoring leg, 2 inch (50 mm) tall vertical section, and 1-3/32 inch (28 mm) tall drip lip with 1-1/16 inch (27 mm) offset from the vertical section.



2.14.6 Schluter-BARA-RTK2.14.6.1 Description: color-coated aluminum profile with a 3-11/32 inch (85 mm) wide

09 30 05-41

integrated trapezoid-perforated anchoring leg, 2-1/2 inch (63 mm) tall vertical section, 1-1/4 inch (32 mm) tall drip lip with 1-1/32 inch (26 mm) offset from the vertical section, and 3/8 inch (10 mm) deep recessed groove for gutter attachment.



2.14.7 Schluter-BARA-RTP2.14.7.1 Description: color-coated aluminum profile with a 2-5/8 inch (65 mm) tall vertical

section, 1-1/16 inch (27 mm) tall drip lip with 1-3/32 inch (28 mm) offset from the vertical section, and 5/16 inch (8 mm) deep recessed groove for gutter attachment.


2.14.7.3 Color:2.14.7.3.1 PG - Classic Grey.

2.14.8 Schluter-BARIN2.14.8.1 Description: color-coated aluminum gutter with 3-15/16 inch (86 mm) wide, 1-

9/16 inch (40 mm) radius trough and 1-3/16 inch (30 mm) tall anchoring slots spaced at 4 inch (102 mm) along the vertical section.

2.14.8.2 Corners:2.14.8.2.1 Provide with matching inside corners.2.14.8.2.2 Provide with matching outside corners.2.14.8.2.3 Provide with end caps, down couplings, elbow and tee pipes, and spouts

as required.2.14.8.3 Color:

2.14.8.3.1 BW - Bright White.2.14.8.3.2 HB - Light Beige.2.14.8.3.3 RB - Red Brown.2.14.8.3.4 SB - Black Brown.2.14.8.3.5 PG - Classic Grey.2.14.8.3.6 GM - Metallic Grey.

2.15 SETTING MATERIALS

2.15.1 Installation methods as specified in Section 09 30 00 - Tiling.

3 EXECUTION

3.1 EXAMINATION

3.1.1 Do not begin installation until substrates have been properly prepared.

3.1.2 If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

09 30 05-42

3.2 PREPARATION

3.2.1 Clean surfaces thoroughly prior to installation.

3.2.2 Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

3.3.1 Install in accordance with manufacturer's instructions.

3.4 PROTECTION

3.4.1 Protect installed products until completion of project.

3.4.2 Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

09 30 05-43

· web viewheight as required. schluter-bara-rwl description: l-shaped profile with a 3-1/2 inch...

Documents