water purifying system -...

295 East Corporate Place • Suite 100 • Chandler, AZ 85225

Toll Free: 1.800.621.5886 • Phone: 480.893.7607 • Fax: 480.753.3397

[email protected] • www.1Paramount.com

004-027-8780-00 REV122010 US Patent Pending

MADE IN USA

WATER PURIFYING SYSTEMINSTALLATION MANUAL

EC

O FRIEND

LY

PA

RA

MOUNT CERTI

FIE

D

2

®2008, Paramount Pool and Spa Systems

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS: READ COMPLETELYBEFORE PROCEEDING WITH INSTALLATION. SAVE THESEINSTRUCTIONS

When using this electrical equipment, basic safety precautions shouldalways be followed, including the following:

CAUTION: READ AND FOLLOW ALL INSTRUCTIONS

WARNING:

• Follow all applicable electrical codes.

• A qualified licensed electrician should perform electricalhookup.

• Turn off power at main source before making any electricalconnections or servicing the unit.

• Use only liquid-tight flexible nonmetallic conduit for electricalconnections.

• A terminal marked G is located inside the supply terminalcompartment. To reduce the risk of electric shock, thisterminal must be connected to the grounding means providedin the electrical supply service panel with a continuous copperwire equivalent in size to the circuit conductors supplying thisequipment.

• At least one lug marked “BONDING LUG” provided on theexternal surface of the unit. To reduce the risk of electric

3

For technical assistance call 1.800.621.5886 or contact your regional representative

shock, connect the local common bond grid in the area of thepool or spa to this terminal with an insulated or bare copperconductor not smaller than 6 AWG.

WARNING:

• ALWAYS wear safety glasses when using power equipmentduring the installation process.

• Install at least 5 ft from pool or spa water using nonmetallicplumbing. Mount ozone generator near pool equipment atleast one (1) foot above maximum water level to preventwater from contacting electrical equipment. Install inaccordance with the installation instructions.

• Short-term inhalation of high concentrations of ozone andlong-term inhalation of low concentrations of ozone gas cancause serious harmful physiological affects. Do not inhale gasproduced by this unit. If installed in an enclosed space makesure to account for adequate ventilation.

• UV LIGHT PRODUCED BY THIS UNIT IS HARMFUL TOTHE EYES AND MAY CAUSE BLINDNESS. DO NOT LOOKDIRECTLY AT A LIT BULB!

NOTICE TO OWNER:

• Save these instructions and deliver to pool owner wheninstallation is complete.

SAFETY INSTRUCTIONS (CONT.)

4


WHAT IS OZONE AND HOW DOES IT WORK

• Ozone is created from oxygen using a simple yet powerful system of UV bulbs,to be used as a pure shock (oxidizer) for the swimming pool.

• Ozone is injected into the pool water using the Clear O3® suction injectionsystem, where the ozone enriched air is mixed with the water going into thepool circulation pump. This creates a dynamic environment that best mixes theair and water at high pressure as it is sent into the filter

• Once in the water, the ozone breaks down materials such as ammonia, oils, andother non-living waste that are detrimental to chlorine's function in the pool.This occurs between the pump and filter and also in the filter. Chlorine is in a group of the least stable elements and must becombined with another material to become stable. In swimming pools, thisprocess creates the formation of combined chlorines, like chloramines, whichdo not sanitize and have adverse effects on human skin. Use of ozone allowsthe chlorine to work primarily as a water disinfectant.

• Pool water treatment can be broken down into three primary categories:

1. Disinfectant- The killing of living organisms (virus, bacteria, algae). Thisconsumes only 10-20% of the chlorine normally placed in a pool.

2. Oxidation- The removal of non-living waste from pool water. This consumes upto 70% of the chlorine placed in standard treated pools

3. Residual- The remaining, measurable sanitizer is left in the pool as a safety net to maintain the water quality until it is broughtthrough the pool equipment again. Usually less than 10% of the chlorineoriginally placed in a pool is left over as residual.

Installing a Clear O3® Water Purification system will reduce the amount ofchlorine needed to maintain a pool by up to70%.

The benefits of using ozone include:• Fewer chemicals to maintain the pool.• Less work to maintain the pool water.• More enjoyable water, being treated similar to bottled water.• Longer filter cycles, and increased life for the salt chlorinator cells (if present).

TO COMPLETE INSTALLATION YOU WILL NEED THE FOL-LOWING ITEMS (NOT INCLUDED)

(1) Six (6) feet 1/2” non-metallic conduit outdoor rated.

(1) 1/2" conduit compression fitting.

5


SELECTING LOCATION & MOUNTING UNIT

1. Select a location on a wall near the pool equipment or insert posts into theground, which will be used to hang unit. The Clear O3® unit should be at leastone (1) foot above maximum water level, and for extra safety the unit shouldbe mounted higher than the filter. The unit should be within five (5) feet of anelectrical source, and within nine (9) feet of plumbing connection. A solidsurface is necessary to mount unit. Mounting brackets are horizontallyadjustable to line up with hard points on the mounting surface. The unit mustbe mounted horizontally and level on the wall. Electrical connections shouldbe facing downward.

2. Use provided screws and plastic wall inserts or poles and pole mount clamps (not included) depending on installationsurface available.

3. Four (4) mountingbrackets areincluded (two for thetop slot and two forthe bottom slot.

4. Install anchors andscrews in desiredlocation for the tophangers. They mustbe no further apart than twelve (12) inches. Do not tighten screws all the way.(Fig. 1)

5. Hang the Clear O3® from the two top brackets by sliding the keyhole slotsover the screws.

Fig. 1:

12" Maximum

6. Mark the location for the two bottom brackets. (Fig. 2)

7. Remove the Clear O3® from the wall and install the wall anchors.

8. Place the Clear O3® unit back on the screws and line up the two lowerbrackets with the wall anchors. (Fig. 3)

9. Install the bottom two screws and tighten all screws.

SELECTING LOCATION & MOUNTING UNIT

6


Fig. 3:

Fig. 2:

MAKING ELECTRICAL CONNECTIONS

7


Fig. 4: 120 Vac 50-60 Hz 0.8A

BLACK

GREEN

WHITE

PWR

GND

NEG PWR LINE 2

GND

PWR LINE 1

WHITE

GREEN

BLACK

230 Vac 50-60 Hz 0.38A

OUTPUT

30-60 Vac 700mA - 800mACLASS P, TYPE 1, RATING: A"RS" ELECTRONIC BALLAST

GREEN

WIRE NUTS

LAMP2X RED

2X BLUE

SIDE OF BALLAST

INPUTS

BLACK

BLACK

GREEN

WHITE

WHITEBLACK

WHITE

WARNING:Turn off power at main source before making any electrical connections or servicing the unit.

1. A licensed electrician should make all electrical connections. Makesure the unit is grounded by connecting to the pool equipments bondwire to comply with local electrical codes. See wiring diagram (Fig. 4).

2. Turn off power to the filtration system pump at the circuit breaker.

3. Install an approved seal tight flex conduit (not included) rated foroutdoor use between the Clear O3® unit and filtration system pumptime clock with the wires running inside (Fig. 5A & 5B). Electricalconnections should be facing downward.

4. Connect green ground wire to the time clock ground bar (Fig. 6A). TheClear O3® unit is set to 240VAC to be connected to the load side (Fig.6B) of the filtration pump time clock. The ballast may be switched to120VAC if needed (Fig. 7). See wiring diagram (Fig. 4). (Go to page21-23 for complete instructions on changing the ballast setting)

MAKING ELECTRICAL CONNECTIONS (CONT.)

8


Fig. 5A Fig. 5B

Fig. 6BFig. 6A

Fig. 7

Ground Lug

MAKING ELECTRICAL CONNECTIONS (CONT.)

9


The Clear O3® shouldrun with the filter pumpas the filter pumpcreates the air drawthrough the unit neededto create ozone. Do notset the Clear O3® to runwhen the filter pump isoff and not pulling airthrough the unit.

5. Use external ground lugto connect the Clear O3®

to the pool pump groundbond. (Fig. 8)

6. Turn on power to filtrationsystem pump. Check glowtube on the left front of theClear O3®. A light blue lightindicates lamp is lit and theunit should be producingozone. (Fig. 9)

Fig. 9

Fig. 8

Ground Lug

Light Blue Glow Tube

WARNING:UV light produced by this unit is harmful to theeyes and may cause blindness! Do not lookdirectly at a lit bulb!

10


MAKING PLUMBING CONNECTIONS

1. Turn off power to the filtration system pump at the circuitbreaker.

2. Pump strainer pot installation: (Fig. 10)

2.1 Check pump elevationabove water level. Refer to(Chart 1) for proper checkvalve selection. The 0.5 lbvalve comes standard withClear O3® and others areavailable to orderseperately.

2.2 Remove strainer pot plug. Ifthere is an O-Ring on plugtake O-Ring off of pot plugand slide over threaded endof check valve.

2.3 Wrap the check valve fourtimes with teflon tape andinstall into the strainer potplug-hole. Add more tapeif valve does not seal.(Fig. 11)

Fig. 10

Fig. 11

Chart 1

Pump Elevation Above Water Level Check Valve Rating

1’ (30cm) 0.5 lb

2’ (60cm) 1.5 lb

4’ (120cm) 3.0 lb

5’ (150cm) 4.0 lb

2.4 Install the combinationneedle valve flow meter onthe bottom of the ClearO3® unit. (Fig. 12)

2.5 Install 3/8 OD x 1/4 IDtubing to compression endof check valve. (Fig. 13)

3. Pre-pump standpipeinstallation: (Fig. 14A & 13)

3.1 Cut cap off standpipe.

3.2 Glue a 3/4" elbow and a3/4" x 1/4" NPTreducer bushing on endof standpipe.

3.3 Install the threaded endof the check valveincluded in the reducer bushing.

3.4 Install 3/8 OD x 1/4ID tubing to barbedend of check valve. (Fig. 13)

MAKING PLUMBING CONNECTIONS (CONT.)

11


Fig. 12

Fig. 14A NOT TO SCALE

WATER LINE

2" PIPE

3/4" PIPE 3/4" PIPE

WATER LINE

2" PIPE

3/4" PIPE

Fig. 13

WATER LINE

TO SKIMMER

TO MDX

CLEAR O3

3-WAY VALVE

2-WAY VALVE

CHECK VALVE

*NOT TO SCALE*2-WAY VALVE

3/4" PIPE2" PIPE

WATER LINECLEAR O3

CHECK VALVE


12


4. OPTIONAL SUBMERGED EQUIPMENT INSTALLATION (Fig. 14B)

To complete this installation option you will need a two way valvenot included.

4.1 Install the two way valve on the inlet pipe to the pump suction.(before the standpipe if installed)

4.2 Make all other connections before the two way valve.

4.3 Make tubing connections to the pump pot or standpipe as instandard pump above water level installation.

4.4 Start the pump with the valve fully open.

4.5 Note the filter pressure. Then close the valve slightly until thepressure on the filter drops two or three psi.

4.6 Go to setting theairflow on page 16to finish settingairflow.

The slightrestriction thiscreates on thepump is the sameas if it was set atapproximately onefoot above waterlevel and allows thepump to draw air inat the pump pot orstandpipe.

(Fig. 14B)

Fig. 14B


13


5. Lay the 3/8 tubing alongdesired route to thecompression fitting on thecombination needle valveflow meter on the Clear O3®

unit.

6. Connect the tubing to thecompression fitting. (Fig. 15)

7. Use the provided wires tiesto tie the loose tubing to theconduit or plumbing. (Fig. 16)

Fig. 15

Fig. 16

OPTIONAL SUBMERGED EQUIPMENT INSTALL.

14


New Installation using Paramount venturiinstallation kit.

TO COMPLETE THIS INSTALLATION YOUWILL NEED THE FOLLOWING ITEMS

(NOT INCLUDED)(2) 2” X 2” X ¾” SLIP TEE (1) ¾” X ¾” UNIONBALL VALVE (2) 2” VALVES ¾” FITTINGSAND PIPE (2) ¾” UNIONS NOTE: ¾” PLUMBING CAN BE 2” IF NEEDEDFOR STRENGTH

1. Install two ea. 2" inch valves, and twoeach 2 X 2 by ¾ inch tees. One valveand one tee on the suction side of thepump and one tee and valve on thereturn side of the pump (before theheater). (Fig. 17)

2. Plumb ¾ inch PVC from pressure sidetee into a union ball valve. (Fig. 18A)

3. Plumb ¾” inch PVC from the ball valveinto the inlet side of the venturi(coming from the return line after thefilter before the heater if it has one.(Fig. 18B)

4. Plumb ¾” inch PVC from the suctionside tee to a ball valve and union andthen into the outlet side of the venturi.Note the venturi must be level and theremovable for cleaning. The flowarrow on the venturi must point toshow the flow to the suction side ofthe pump. (Fig. 18B)

Fig. 17

Fig. 18A

Fig. 18B

5. Install the 3/8” OD x ¼ ID tubing onthe barbed end of the venturi, withthe check valve installed in-line. Notethe correct direction of flow throughthe check valve. (Fig. 19A & 19B)

6. Connect the tubing to thecompression fitting. (Fig. 20)

7. Connect the compression fitting tothe flow meter. (Fig 21)

OPTIONAL SUBMERGED EQUIP. INSTALL.(CONT.)

15


Fig. 19

Fig. 20 Fig. 21

Fig. 19B

SETTING AIR FLOW

16


1. Clean filter and pump basket before setting airflow.

2. Turn the knob on the needle valve/flow meter clockwise to closevalve completely.

3. Turn the power on to the pump

4. Turn the knob on the needle valve/flow meter counter clockwise untilthe ball reads in the middle of the two lines on the flow meter. (Fig.22)

NOTE: IF THE PUMP THAT THE CLEAR 03® UNIT IS INSTALLED ONIS A PUMP RUNNING A PARAMOUNT IN-FLOOR SYSTEM, lock thewater valve on pause when the valve is switching ports andtherefore at it’s maximum flow (the pause control is located on topof the Paramount water valve). Set the flow meter so the ball is onthe upper line of the Ideal range.

NOTE: WHEN USING MULTIPLE SPEED PUMPS, SET THE FLOWMETER WITH THE PUMP RUNNING ON THE HIGHEST SPEEDTHAT WILL BE USED.

Fig. 22

EXTERNAL SAFETY AIR BLEED KIT INSTRUCTIONS (OPTIONAL)

17


Sometimes the internalair bleed on the filter isnot sufficient to handlethe extra air in the systemwith an ozonator installed.An External Safety AirBleed Kit (006-402-3872-00) (Fig. 23) forin-ground swimmingpools is available toremove excess air fromthe filter and send itdownstream (up to 15')past all equipment. Afterinstalling always test per instructions that air is vented from the filter whenthe pump is running. You must install an external air bleed if the filter is old,does not have an internal air bleed, there is a solar system on the pool orthere is a robotic pressure side cleaner.

Mounting Instructions

1. Turn the power off tothe pump.

2. Remove the pressuregauge from the filter.

3. Install the nipple into oneend of the brass tee.

4. Install the pressuregauge by threading intothe other end of thebrass tee supplied.

5. Install the tubingcompression fitting bythreading into the side of the brass tee.

External Safety Air Bleed Kit

FromPump

Filter Heater

Biostat/Biocide

Chlorinator

Return Line

4

321

Installation of External Safety Air Bleed Kit

Fig. 23

Fig. 24

EXTERNAL SAFETY AIR BLEED KIT INSTRUCTIONS (OPTIONAL) (CONT.)

18


6. Install the tee assembly by threading into the hole where youremoved the pressure gauge (Fig. 24 Pg. 17).

7. Insert one end of the tubing into the compression fitting (Fig. 24 Pg. 17).8. Turn the power on to the pump and check that air is coming from theother end of the tubing.

9. Turn the power off to the pump.10. Pick a spot on the return pipe downstream of all other devices

(heater, chlorinator, pressure cleaner, etc.) 11. Drill a 7/16" hole through the return pipe at the location

selected. 12. Install the saddle clamp with the fitting over the hole.

Make sure the gasket is in place between the fitting and the pipe.(Fig. 24 Pg. 17)

13. Lay the tubing along the return pipe to the saddle clamp fitting andcut off excess length.

14. Connect the end of the tubing to the compression fitting on thesaddle clamp (Fig. 24 Pg. 17). The tubing can be secured to thepipe using cable ties (not included).

NOTE:Ozone production from direct UV light will decline over time. UV bulbscontinue to illuminate after they stop producing an effective level of ozoneto clean your pool water. To make sure your pool continues to receive all thebenefits of ozone, Paramount recommends that you replace your bulb everythree (3) years.

WARNING:• Turn off power at main source before making any electricalconnections or servicing the unit.

• UV light produced by this unit is harmful to the eyes andmay cause blindness! Do not look directly at a lit bulb!

BULB REPLACEMENT

BULB REPLACEMENT (CONT.)

19


1. Turn the power off tofiltration system pumpat circuit breaker.

2. Remove three screwsin left end side caplabeled “electricalconnections”. (Fig.25)

3. Remove side cap.(Fig. 26)

4. Grasp light bulb plugand pull light out about oneinch. (Fig. 27)

Fig. 25

Fig. 26

Fig. 27

BULB REPLACEMENT (CONT.)

20


5. Remove plug fromlight bulb. (Fig. 28)

6. Pull light bulb freefrom Clear O3®

unit. (Fig. 29)

7. Make sure gasket isin place onreplacement lightbulb.

8. Align with key andslide into hole untilbulb seats firmlyand completely intounit. (Fig. 30)

9. Press plug ontolight bulb.

10. Replace side capand three screws.

11. Turn on power tofiltration systempump.

12. Check glow tubeon the left front ofthe Clear O3®. Alight blue lightindicates lamp is litand the unit shouldbe producingozone.

Fig. 29

Fig. 30

Fig. 28

TROUBLESHOOTING & SERVICE

21


ISSUE SOLUTION

1. No air bubbles Clean filter then adjust entering system or pool airflow needle valve.

2. Filter empties and Replace check valve pump loses prime fitting at strainer pot.

3. Light bulb does not light Check power to Clear O3®, then replace bulb.

1. Turn off the power at the breaker andremove the unit from wall mounting.

2. With a Phillips screwdriver, remove thethree (3) screws in the left end side cap,labeled electrical connections.(Fig. 31)

3. Remove side cap by pulling out from theend of the unit.

4. Inside the open electrical housing, findthe light bulb plug and pull it out aboutone inch. (Fig. 32)

CONVERTING BALLAST VOLTAGE TO ALTERNATE SETTING

Fig. 31

Fig. 32

22


CONVERTING BALLAST VOLTAGE TO ALTERNATE SETTING(CONT.)

5. While holding the bulb, wiggle the plug toloosen from the bulb and pull it free fromlight bulb.(Fig. 33)

6. Pull the light bulb from the unit.

7. With a Phillips screwdriver, remove thetwo (2) screws inside the electricalhousing next to the light bulb hole thatconnect the electrical housing to thealuminum housing.(Fig. 34)

8. While holding the aluminum housing,remove the electrical housing by pullingfrom the end of the unit. (Wires do notneed to be disconnected.)

9. Inside the back cavity of the aluminumhousing you will see the ballast and anut holding the two groundwires in place.(Fig. 35)

Fig. 33

Fig. 34

Fig. 35

GroundWire

23


10. On the back of the unitnearest the open end,remove the flatheadedscrew with a Phillipsscrewdriver while holdingthe lock nut on the insideof the cavity with pliers.(Fig. 36)

11. Pull the ballast plate freefrom housing.

12. On the side of the ballastis a switch to selectvoltage. Push the switch closest to the desired setting(120V or 240V) (Fig. 7 Pg. 8)

13. Reassemble in reverse.

14. Be sure to install ground wire connectors under lock nut, holdingballast in place(Fig. 35 Pg. 22).

Fig. 36

CONVERTING BALLAST VOLTAGE TO ALTERNATE SETTING(CONT.)

WARRANTY INFORMATION

24

Par

amou

nt P

ool &

Spa

Sys

tem

s (P

P&

SS

)2

95

E. C

orpo

rate

Pla

ce, S

uite

10

0C

hand

ler,

AZ

85

22

51

.80

0.6

21

.58

86

ww

w.1

Par

amou

nt.c

om

In c

ompl

ianc

e w

ith t

he M

agnu

son-

Mos

s W

arra

nty-

Fede

ral

Tra

de C

omm

issi

on A

ct (

Publ

ic L

aw

9306

37, P

aram

ount

Poo

l & S

pa S

yste

ms

(PP&

SS)

prov

ides

the

follo

win

g lim

ited

war

rant

ies.

CO

ND

ITIO

NS

Thi

s lim

ited

war

rant

y sh

all b

e su

bjec

t to

the

orig

inal

ow

ner

com

plyi

ng w

ith th

e fo

llow

ing

cond

i-tio

ns: 1. T

he s

wim

min

g po

ol s

hall

be k

ept f

ull o

f w

ater

at a

ll tim

es e

xcep

t for

pur

pose

s fo

r re

pair

or

mai

nten

ance

not

to e

xcee

d fiv

e (5

) da

ys.

2. T

he P

P&SS

sys

tem

sha

ll be

ope

rate

d by

the

orig

inal

ow

ner w

ith re

ason

able

car

e an

d ne

ces-

sary

mai

nten

ance

.3.

Reg

istr

atio

n ca

rd m

ust b

e m

aile

d to

PP&

SS w

ithin

thir

ty (

30)

days

of

pool

com

plet

ion.

PP

&S

S N

OZ

ZLE

AN

D B

OD

Y (

EX

CLU

DIN

G P

OO

L V

ALE

T R

ET

RO

) A

SS

EM

BLIE

SLIM

ITE

D L

IFE

TIM

E M

AN

UFA

CT

UR

ER

S W

AR

RA

NT

YPP

&SS

war

rant

s to

the

orig

inal

ow

ner,

mat

eria

ls a

nd e

quip

men

t to

be f

ree

of d

efec

ts f

or a

s lo

ng

as o

rigi

nal o

wne

r ow

ns p

ool,

dete

rmin

ed u

nder

this

war

rant

y to

be

for

the

“Lif

etim

e” o

wne

rshi

p by

ori

gina

l ow

ner f

rom

dat

e sw

imm

ing

pool

is p

last

ered

or o

ptio

nal i

nter

ior s

urfa

ce fi

nish

app

lied.

T

he m

ater

ials

and

equ

ipm

ent c

over

ed u

nder

the

“Lif

etim

e” w

arra

nty

are

the

PP&

SS N

ozzl

e an

d B

ody

Ass

embl

y. (

PVC

plu

mbi

ng i

nsta

lled,

lab

or, m

ater

ial

and

all

othe

r w

ork

perf

orm

ed b

y co

n-tr

acto

rs is

not

cov

ered

und

er P

P&SS

War

rant

y.)

PP

&S

S R

ET

RO

JET

S (

CA

RE

TA

KE

R, C

AR

ETA

KE

R 9

9, G

AM

MA

3, N

ET

N’ C

LE

AN

, P

OO

L V

ALE

T R

ET

RO

, QU

IKC

LE

AN

1, Q

UIK

CLE

AN

2)

LIM

ITE

D M

AN

UFA

CT

UR

ER

S

1-Y

EA

R W

AR

RA

NT

YPP

&SS

war

rant

s to

ori

gina

l ow

ner,

mat

eria

ls, a

nd e

quip

men

t to

be f

ree

of d

efec

ts f

or a

per

iod

of

one

(1)

year

fro

m d

ate

of p

urch

ase.

The

mat

eria

ls, p

arts

, and

/or

rela

ted

com

pone

nt p

arts

sup

plie

d or

dis

trib

uted

by

PP&

SS a

re c

over

ed u

nder

thi

s on

e (1

) ye

ar l

imite

d w

arra

nty.

(PV

C p

lum

bing

in

stal

led,

labo

r, m

ater

ial a

nd a

ll ot

her w

ork

perf

orm

ed b

y co

ntra

ctor

s is

not

cov

ered

und

er P

P&SS

W

arra

nty.

)P

P&

SS

MD

X2 A

NT

I-E

NT

RA

PM

EN

T D

EB

RIS

DR

AIN

AN

D M

DX

-R3

VG

B C

OM

PLI-

AN

T D

EB

RIS

DR

AIN

LIM

ITE

D M

AN

UFA

CT

UR

ER

S 1

-YE

AR

WA

RR

AN

TY

PP&

SS w

arra

nts

to o

rigi

nal o

wne

r, m

ater

ials

, and

equ

ipm

ent t

o be

fre

e of

def

ects

for

a p

erio

d of

on

e (1

) ye

ar f

rom

dat

e of

sw

imm

ing

pool

sta

rt-u

p. T

he m

ater

ials

, par

ts a

nd/o

r re

late

d co

mpo

nent

pa

rts

supp

lied

or d

istr

ibut

ed b

y PP

&SS

are

cov

ered

und

er th

is o

ne (1

) yea

r lim

ited

war

rant

y. (P

VC

pl

umbi

ng i

nsta

lled,

lab

or,

mat

eria

l an

d al

l ot

her

wor

k pe

rfor

med

by

cont

ract

ors

is n

ot c

over

ed

unde

r PP

&SS

War

rant

y.)

PP

&S

S S

TE

PC

LE

AN

AS

SE

MB

LIE

S L

IMIT

ED

MA

NU

FA

CT

UR

ER

S

2-Y

EA

R W

AR

RA

NT

YPP

&SS

war

rant

s to

ori

gina

l ow

ner,

mat

eria

ls, a

nd e

quip

men

t to

be f

ree

of d

efec

ts f

or a

per

iod

of

two

(2)

year

s fr

om d

ate

of p

urch

ase.

The

bod

ies,

noz

zles

, wat

er v

alve

and

/or

rela

ted

com

pone

nt

part

s su

pplie

d or

dis

trib

uted

by

PP&

SS a

re c

over

ed u

nder

thi

s tw

o (2

) ye

ars

limite

d w

arra

nty.

(P

VC

plu

mbi

ng in

stal

led,

labo

r, m

ater

ial a

nd a

ll ot

her

wor

k pe

rfor

med

by

cont

ract

ors

is n

ot c

ov-

ered

und

er P

P&SS

War

rant

y.)

PP

&S

S D

IST

RIB

UT

ION

WA

TE

R V

ALV

E L

IMIT

ED

MA

NU

FA

CT

UR

ER

S 3

-YE

AR

WA

RR

AN

TY

Para

mou

nt w

ater

val

ve m

odul

e an

d ho

usin

g ar

e w

arra

nted

-for

a p

erio

d of

3 y

ears

to

be f

ree

of

man

ufac

turi

ng d

efec

ts i

nclu

ding

wea

r an

d te

ar o

n pr

oduc

t fr

om d

ate

of p

ool

star

t-up

. Thi

s w

ar-

rant

y ap

plie

s to

the

ori

gina

l po

ol o

wne

r on

ly.

Rep

lace

men

t pa

rts

ther

eaft

er a

re w

arra

nted

for

a

peri

od o

f 1

year

.

PP

&S

S D

EB

RIS

CO

NTA

INM

EN

T C

AN

IST

ER

LIM

ITE

DM

AN

UFA

CT

UR

ER

S 3

-YE

AR

WA

RR

AN

TY

PP&

SS w

arra

nts

to o

rigi

nal o

wne

r, m

ater

ials

, and

equ

ipm

ent t

o be

free

of d

efec

ts fo

r a p

erio

d of

th

ree

(3) y

ears

from

dat

e of

sw

imm

ing

pool

sta

rt-u

p. T

he m

ater

ials

and

equ

ipm

ent c

over

ed u

nder

th

is th

ree

(3)

year

war

rant

y is

the

PP&

SS D

ebri

s C

onta

inm

ent C

anis

ter

Hou

sing

. (PV

C p

lum

b-in

g in

stal

led,

lab

or, m

ater

ial

and

all

othe

r w

ork

perf

orm

ed b

y co

ntra

ctor

s is

not

cov

ered

und

er

PP&

SS W

arra

nty.

) The

PP&

SS C

anis

ter

Deb

ris

Con

tain

men

t Bas

ket,

Inte

rnal

Can

iste

r L

id, a

nd

Top

Dec

k L

id a

re c

over

ed f

or a

per

iod

of o

ne (

1) y

ear

unde

r th

is w

arra

nty.

OT

HE

R R

ELA

TE

D S

YST

EM

PA

RT

S, A

NC

ILLA

RY

PA

RT

S A

ND

RE

PLA

CE

ME

NT

PA

RT

S L

IMIT

ED

MA

NU

FA

CT

UR

ER

S 1

-YE

AR

WA

RR

AN

TY

PP&

SS w

arra

nts

to o

rigi

nal o

wne

r, m

ater

ials

, and

equ

ipm

ent t

o be

free

of d

efec

ts fo

r a p

erio

d of

on

e (1

) yea

r fro

m d

ate

of s

wim

min

g po

ol s

tart

-up.

The

mat

eria

ls, p

arts

and

/or r

elat

ed c

ompo

nent

pa

rts

supp

lied

or d

istr

ibut

ed b

y PP

&SS

are

cov

ered

und

er t

his

one

(1)

year

lim

ited

war

rant

y.

(PV

C p

lum

bing

ins

talle

d, l

abor

, m

ater

ial

and

all

othe

r w

ork

perf

orm

ed b

y co

ntra

ctor

s is

not

co

vere

d un

der

PP&

SS W

arra

nty.

) R

epla

cem

ent p

arts

are

war

rant

ed f

or a

per

iod

of 1

yea

r fr

om

the

date

of

purc

hase

.PP

&SS

war

rant

s to

ori

gina

l ow

ner

a on

e (1

) ye

ar li

mite

d w

arra

nty

that

he

PP&

SS r

elat

ed c

om-

pone

nt p

arts

to b

e fr

ee o

f de

fect

s fr

om th

e tim

e of

inst

alla

tion.

RE

PLA

CE

ME

NT

CO

ND

ITIO

NS

Thi

s w

arra

nty

is th

e re

spon

sibi

lity

of th

e ow

ner t

o re

mov

e th

e PP

&SS

Noz

zle

& B

ody

Ass

embl

y,

Dis

trib

utor

Wat

er V

alve

Top

/Bot

tom

Hou

sing

, Deb

ris

Con

tain

men

t Can

iste

r or o

ther

rela

ted

sys-

tem

com

pone

nts

desc

ribe

d w

ith th

is w

arra

nty,

con

tact

PP&

SS fo

r an

RM

A n

umbe

r, an

d re

turn

it

to P

P&SS

. Shi

p pa

rt in

que

stio

n fr

eigh

t pre

-pai

d, a

nd u

pon

confi

rmat

ion

of d

efec

t, PP

&SS

will

re

pair

or

repl

ace

the

PP&

SS w

arra

nted

at

no c

harg

e to

the

ori

gina

l ow

ner.

The

rep

aire

d or

re-

plac

ed P

P&SS

item

will

be

retu

rned

to th

e or

igin

al o

wne

r w

ith f

reig

ht C

.O.D

. Lab

or to

rei

nsta

ll th

e re

pair

ed o

r re

plac

ed it

em is

the

sole

res

pons

ibili

ty o

f th

e ow

ner.

LIM

ITA

TIO

NS

No

war

rant

y ex

tend

s to

any

par

t of

the

PP&

SS p

arts

or

com

pone

nts

whi

ch is

cau

sed

by a

ny o

f th

e fo

llow

ing

cond

ition

s or

eve

nts:

1. D

efec

ts o

r fa

ilure

s ca

used

by

abus

e, l

ack

of r

espo

nsib

le c

are,

lac

k of

nec

essa

ry m

aint

e-na

nce,

impr

oper

ope

ratio

n, v

anda

lism

, act

s of

God

.2.

Dam

ages

or

failu

res

caus

ed b

y ab

use,

lack

of

resp

onsi

ble

care

, lac

k of

nec

essa

ry m

aint

e-na

nce,

impr

oper

ope

ratio

n, v

anda

lism

, act

s of

God

.3.

PP&

SS e

xpre

ssly

den

ies

any

resp

onsi

bilit

y or

lia

bilit

y fo

r in

cide

ntal

or

cons

eque

ntia

l da

mag

es a

risi

ng o

ut o

f, o

r as

a r

esul

t of

, use

or

owne

rshi

p of

you

r PP

&SS

par

ts o

r as

a

resu

lt of

use

or

owne

rshi

p of

you

r PP

&SS

par

ts o

r co

mpo

nent

s, o

r ot

her

rela

ted

prod

ucts

co

vere

d un

der

this

lim

ited

war

rant

y.4.

Any

def

ects

cau

sed

by a

cts

of G

od, s

uch

as s

torm

s, e

arth

quak

es, g

roun

d m

ovem

ent,

or

free

zing

, etc

., th

at a

re b

eyon

d th

e no

rmal

con

ditio

ns.

5. I

nsta

llatio

n of

the

PP&

SS S

yste

m b

y no

n-au

thor

ized

ins

talle

r m

ay r

ende

r th

is w

arra

nty

null

and

void

.So

me

stat

es d

o no

t allo

w th

e ex

clus

ion

or li

mita

tion

of in

cide

ntal

or

cons

eque

ntia

l dam

ages

, so

the

abov

e lim

itatio

ns o

r ex

clus

ions

may

not

app

ly to

you

.Im

plie

d w

arra

ntie

s ar

e lim

ited

in d

urat

ion

to t

he d

urat

ion

of th

e w

ritte

n lim

ited

war

rant

y he

re-

with

in. S

ome

stat

es d

o no

t allo

w li

mita

tions

on

how

long

an

impl

ied

war

rant

y la

sts,

so

the

abov

e lim

itatio

ns m

ay n

ot a

pply

to y

ou.

Thi

s w

arra

nty

give

you

spe

cific

lega

l rig

hts,

and

you

may

als

o ha

ve o

ther

rig

hts

that

may

var

y fr

om s

tate

to s

tate

.00

4-02

7-79

87-0

0 P

AR02

13 1

1191

0

othe

r U

.S. a

nd in

tern

atio

nal p

aten

ts p

endi

ng

CLEAR 03® WATER PURIFYING SYSTEM

25


512

94

68

11

12

3

10

7

1413

16 18

(opt

ional)

(opt

ional)

(opt

ional)

1715

CLEAR 03® WATER PURIFYING SYSTEM

26


Item Part Number DescriptionSINGLE UNIT1. 004-402-3880-00 Clear O3® Single Assembly2. 005-402-3834-00 Lamp3. 005-402-3820-00 Mounting Brackets (4Pk)4. ** Ground Lug5. 005-402-1384-00 Conduit Compression Fitting 1/2"6. ** Wiring Harness 3-Wire 12 Gauge X 6ft7. 005-402-3361-00 Tubing with Check Valve, Pump Mount,

& Wire Ties8. ** Compression Nut 1/4" X 3/8"9. ** Tubing 3/8" OD X 1/4" ID X 10ft10. ** Pump Mount Check Valve 1/4"

NPT x barb11. ** Wire Ties (4 pk)12. 005-402-3247-00 Flow Meter Kit13. ** Anchor #1014. ** Screw: 10 x 3/4 PHIL PH15. 005-402-1050-00 Clear O3® Adapter Pot Plug (optional)

16. 005-402-3824-00 Ballast & FilterAIR BLEED KIT17. 006-402-3872-00 Clear O3® Air Bleed Kit (optional)

18. 005-252-3250-00 Venturi Injector Kit (optional)* Not Shown** Not available to purchase individually

WARRANTY REGISTRATION

POOL OWNER INFORMATION

Name:

Address:

City:

State:

Zip Code:

Telephone:

Fax:

E-mail:

Pool Start-Up Date Purchased:

Type of Pool (check one): Concrete Vinyl

Fiberglass

Type of Pool System (check one): PCC 2000 PV3

Pool Valet Cyclean

Vanquish Vantage

Ecopool

POOL BUILDER INFORMATION

Name:

Address:

City:

State:

Zip Code:

When complete, remove this page, fold, stamp and return to Paramount Pool & Spa Systems.

Postal Service: 295 East Corporate Place, Suite 100 • Chandler, AZ 85225Fax: 480.753.3397E-mail: [email protected]: www.1Paramount.com/products/warranty.php

A one (1) year warranty on Clear O3®parts shall be subject to the originalowner, as stated in the “Other RelatedSystem Parts and Replacement PartsLimited Manufacturer’s 1-Year Warranty.”

Cut Here and Return to Paramount

Paramount Pool & Spa Systems

295 East Corporate Place, Suite 100

Chandler, AZ 85225

Staple Here

PlaceStampHere

Fold Here

Cut H

ere and Return to P

aramount

water purifying system -...

Documents