warranty - application gins and booms › catalogfull › 1200-ginsbooms-en.pdfthe gin beam can be...
TRANSCRIPT
Gin
s a
nd
Bo
om
s –
12
00
Page 1201March 2020Phone: 573-682-5521 Email: [email protected] Web: hubbellpowersystems.com
InsulatedHand Tools
Warranty - MaterialHubbell Power Systems, Inc. warrants all products sold by it to be merchantable (as such term is defined in the Uniform Commercial Code) and to be free from defects in material and work-manship. Buyer must notify the Company promptly of any claim under this warranty. The Buyer's exclusive remedy for breach of this warranty shall be the repair or replacement, F.O.B. factory, at the Company's option, of any product defective under the warranty which is returned to the Company within one year from the date of shipment. NO OTHER WARRANTY, WHETHER EXPRESS OR ARISING BY OPERATION OF LAW, COURSE OF DEALING, USAGE OF TRADE OR OTHERWISE IMPLIED, SHALL EXIST IN CONNECTION WITH THE COMPANY'S PRODUCTS OR ANY SALE OR USE THEREOF. The Company shall in no event be liable for any loss of profits or any consequential or special damages incurred by Buyer. The Company's warranty shall run only to the first Buyer of a product from the Company, from the Company's distributor, or from an original equipment manufacturer reselling the Company's product, and is non-assignable and non-transferable and shall be of no force and effect if asserted by any person other than such first Buyer. This warranty applies only to the use of the product as intended by Seller and does not cover any misapplication or misuse of said product.
Warranty - ApplicationHubbell Power Systems, Inc. does not warrant the accuracy of and results from product or system performance recommendations resulting from any engineering analysis or study. This applies regardless of whether a charge is made for the recommendation, or if it is provided free of charge.
Responsibility for selection of the proper product or application rests solely with the purchaser. In the event of errors or inaccuracies determined to be caused by Hubbell Power Systems, Inc., its liability will be limited to the re-performance of any such analysis or study.
0.05 to 1.01.1 to 15.015.1 to 36.036.1 to 46.046.1 to 72.572.6 to 121138 to 145161 to 169230 to 242345 to 362500 to 550765 to 800
(ft.-in.) (m)
Nominal Voltagein Kilovolts
Phase-to-Phase
Phase-to-ground exposure
Distance
Phase-to-phase exposure
(ft.-in.) (m)
*2-12-42-73-03-23-74-05-38-611-314-11
*0.640.720.770.900.951.091.221.592.593.424.53
*2-22-72-103-64-34-115-87-612-618-126-0
*0.660.770.851.051.291.501.712.273.805.507.91
Live-Line Work Minimum Approach Distances • Distances agree withOSHA guidelines in TableR-6 of the Federal Register,published 1/31/94. Thesedistances take into consider-ation the highest switchingsurge an employee will beexposed to on any systemwith air as the insulatingmedium and the maximumvoltages shown.
• The clear live-line tool dis-tance shall equal or exceedthe values for the indicatedvoltage ranges.
*Avoid contact.
Section
2100
©Copyright 2011 Hubbell Incorporated • 210 North Allen Street • Centralia, MO 65240 USAwww.hubbellpowersystems.com
E-mail: [email protected]
NOTE: Because Hubbell has a policy of continuous product improvement, we reserve the right to change design and specifications without notice.
Printed in USA
NOTICE: For latest revision of our Catalog and Literature, please visit our web site: www.hubbellpowersystems.com
Gins andBooms
Catalog 1200 March 2020
Gin
s a
nd
Bo
om
s –
12
00
Gin
s a
nd
Bo
om
s –
12
00
1200 Gins-Booms_0320.indd 12011200 Gins-Booms_0320.indd 1201 3/16/20 2:43 PM3/16/20 2:43 PM
Gin
s an
d B
oo
ms – 1
20
0
Page 1202 March 2020Phone: 573-682-5521 Email: [email protected] Web: hubbellpowersystems.com
Safety Considerations• A swivel-hook block should always be used in the eye
of the gin and a sheave or capstan near the bottom of the structure should be used to thread handline
• Gins are not intended for applications involving side pull on the hoist line or with the lift load in a tagged-out position
• Load line should be parallel to the gin pole• When calculating load capacities, allow 10 percent for
friction in rope pulleys• For example, using two double-sheave blocks,
maximum lift load would be 1,400 lbs.; or, using a single sheave, maximum lift load would be 900 lbs.
Swivel-Top Chain Gin• Same application as Transformer Gin, but top eye casting
can be swiveled to bypass secondary lines, when necessary• Cap is not intended to swivel while under load• Gin has identical load ratings to gins above• Features 48” Epoxiglas® mast and with two wheel tighten-
ers and 36” chain units
Catalog No.
C4000440
Weight
37 lb./16.7 kg.
DescriptionSwivel Top
5" Extended Base Chain Gin
STRAP-TYPE TRANSFORMER GINSFeatures & Applications• Same as Chain-Type Gins, except with a strap-type-ratchet-
action mounting mechanism rather than a chain binder• With 10,000-lb. rated tensile strength, the 2”-wide poly-
ester strap comes in 44” length to fit most structures• Wide handle opening on rapid-action ratchet permits easy
operation, even with gloves• Both models feature 2000-lb. maximum ratings, including
load and fall-line pull
Catalog No.T4001937T4001938
Weight141/4 lb./6.4 kg.181/4 lb./8.2 kg.
DescriptionStandard-Base Strap Gin
5" Extended-Base Strap Gin
Epoxiglas® pole: 3" diameter, 26" length
T4001938
Strap Binder Kit
Catalog No.T4002007
Weight41/2 lb./2 kg.
DescriptionD-Buckle Strap Binder only
C4000315 5" Base
C4000090Standard Base
T4001937
C4000440 Swivel Top
5” Base
CHAIN BINDER TYPE TRANSFORMER GINSAvailable in a standard-base and extended-base design, these proven Chain Binder Type Transformers Gins are versatile tools for hoisting distribution transformers and apparatus up a structure.
Features & Applications• Standard base unit is for mounting on clear pole
sections• 5” extended-base model allows bridge mounting up to
4” x 5” crossarms• Wheel tightener and 36” chain are part of each unit• Standard and extended-base models feature 2000-lb.
maximum ratings, including hand pull force• 900-lb. lift load with single hoist line through a pulley
on the gin and a sheave near the base of structure (lift load plus pull load equals capacity)
• Lift load can be 1,400 lbs., using 4-4 blocks• Pole length is 26 inches
Catalog No.C4000090C4000315
Weight15 lb./6.75 kg.
30 lb./9 kg.
DescriptionStandard Base Chain Gin
5" Extended Base Chain Gin
Safety Considerations• A swivel-hook block should always be used in the eye of
the gin and a sheave or capstan near the bottom of the structure should be used to thread handline
• Gins are not intended for applications involving side pull on the hoist line or with the lift load in a tagged-out posi-tion
• Load line should be parallel to the gin pole• When calculating load capacities, allow 10 percent for
friction in rope pulleys• For example, using two double-sheave blocks, maximum
lift load would be 1,400 lbs.; or, using a single sheave, maximum lift load would be 900 lbs.
CHAIN-BINDER GINS
STRAP-TYPE GINS
1200 Gins-Booms_0320.indd 12021200 Gins-Booms_0320.indd 1202 3/16/20 2:44 PM3/16/20 2:44 PM
Gin
s a
nd
Bo
om
s –
12
00
Page 1203March 2020Phone: 573-682-5521 Email: [email protected] Web: hubbellpowersystems.com
INSULATED GIN POLE/CARGO BOOMInsulated Gin Pole is equipped with three chain tighteners which can be mounted to the pole to give lifting capacities of 5,000 pounds.• Top casting is fitted with two clevises for convenience in loading.• Placing a pole clamp in the swivel lug allows use of wire tong for stabilizing the gin.
Insulated Cargo Boom is rated at 1,000-pound capacity.• Center casting can be adjusted to three possible positions for guy loading the tool.• Base mounting is hinged to permit pivoting of the tool from horizontal upward 90° to vertical and will also swivel a full 180°, depending upon the proximity to the structure.• Casting at the top is the same as on the Insulated Gin Pole.
Features & Applications• Yoke casting fits over distribution crossarms, allowing
gin to be used with rope blocks• Can also be used with rope blocks or handline to lift
conductors from their insulators• Removable cadmium-plated steel pin provides
adjustment for crossarm from 3-1/2” x 4-1/2” up to 4-3/4” x 5-3/4”
• Convertible model fits up to 6” x 6” crossarm
Safety Considerations• At 30° maximum angle from vertical, 44” gin has
rated working load including pull force of 750 lbs.• 500 lb. 56" gins are not intended for side-pull
applications on hoist line or load line• Lines to be within 5° of vertical
Catalog No.H20
T4000870T4001708
Weight10 lb./4.5 kg.12 lb./5.5 kg.10 lb./4.5 kg.
Description44" Crossarm Gin56" Crossarm Gin
Convertible44" Crossarm Gin
MULTI-DUTY GIN• Gin clamps at top of pole to lift heavy equipment• Gin can be mounted lower on pole without changing
mounting bracket to avoid obstructions• Sturdy 4” x 4” Epoxiglas® beam gives unit a 2000 lb.
load rating• With beam removed, mounting bracket can be used
by itself for hanging transformers• Maximum rating of gin bracket is 2500 lbs.The gin beam can be rotated in a half circle, swinging the
load away from underbuild obstructions. Rocker-action of the beam, up to 60°, controls distance of the load from the pole.
Catalog No.C4000648
C85W
DescriptionMulti-Duty Gin,Complete
Mounting Bracket with Wheel Tightener
Weight70 lb./31.5 kg.
17 lb./7.7 kg.
C4000648
Square ClampE4000434P
Insulated Cargo BoomC4000475orC4000483
InsulatedGin PoleC4000470orC4000472
Cat. No.C4000470C4000472C4000475C4000483
Weight74 lb./33.3 kg.90 lb./40.5 kg.100 lb./45 kg.96 lb/43.2 kg.
Description 8' Gin Pole/Chain Binders12'Gin Pole/Chain Binders16' Cargo Boom/Chain Binders16' Cargo Boom/Tower Binders
H20or
T4000870
30°max.
T4001708Convertible
Gin
CROSSARM GIN
1200 Gins-Booms_0320.indd 12031200 Gins-Booms_0320.indd 1203 3/16/20 2:44 PM3/16/20 2:44 PM
Gin
s an
d B
oo
ms – 1
20
0
Page 1204 March 2020Phone: 573-682-5521 Email: [email protected] Web: hubbellpowersystems.com
Features & Applications• 2-1/2” diameter Epoxiglas® poles are used to brace
either heavy-duty or medium-duty Swivel Booms in tripod arrangement
• Poles are anchored to steel tower with tower-type saddles (M4742 and M47413)
BOOM SUPPORT POLE
CatalogNo.
H4721112
Pole Diameter& Length21/2" x 12'
OverallLength12'9"
Weight18.5 lb./8.3 kg.
Catalog No.C4000464
C4000465
C4000469
Weight128 lb./57.6 kg.
140 lb./63 kg.
140 lb./63 kg.
Description16' Boom, 8' Mast, Clamps For Tower Mounting18' Boom, 10' Mast, Clamps For Tower Mounting18' Boom, 10' Mast, Chain Binders for Pole Mounting
SWIVEL BOOM — HEAVY DUTYFeatures & Applications• Used on EHV to swing an insulator cradle with
insulators into a structure for repair• 1,000-lb. capacity with 4” x 4” Epoxiglas® horizontal
boom, coupled with 3” round Epoxiglas mast• Unit rigging requires a link stick and hoisting device in
diagonal position• Clamp on square boom can be adjusted to three
possible positions for loading purposes• Casting on end of boom is fitted with two clevices for
convenient loading• Available with swivel boom on pole-mounted
configuration• Also available with four tower-mounting brackets to fit
towers up to 6” to 6” angle legs
Catalog No.H1973814
H1973H10
Weight70 lb./31.5 kg.
61 lb./27.5 kg.
Description14' Boom, 8' Mast, Clamps For Tower Mounting10' Boom, 6' Mast, Chain Binders for Pole Mounting
C4000469
H1973H10
H4721112
Tower Mounting BracketC4000602
• Same tool is also used as horizontal member for trolley pole changeouts of suspension insulators
SWIVEL BOOM — MEDIUM DUTYFeatures & Applications• Used on transmission structures to lift and move an insulator cradle
with insulators into a convenient work position on a structure• 3”-round Epoxiglas® horizontal boom and vertical mast
are designed for 500-lb. ratings when used in a steel-tower configuration
• 600-lb. rating for wood-pole assembly• Insulated link stick and hoist are used in diagonal position to lift
cradle full of insulators clear of deadendFor tower use, three boom support poles should be added in a tripod configuration as shown in the illustration at left below.
1200 Gins-Booms_0320.indd 12041200 Gins-Booms_0320.indd 1204 3/16/20 2:44 PM3/16/20 2:44 PM
Gin
s a
nd
Bo
om
s –
12
00
Page 1205March 2020Phone: 573-682-5521 Email: [email protected] Web: hubbellpowersystems.com
NOTES
1200 Gins-Booms_0320.indd 12051200 Gins-Booms_0320.indd 1205 3/16/20 2:44 PM3/16/20 2:44 PM
Gin
s an
d B
oo
ms – 1
20
0
Page 1206 March 2020Phone: 573-682-5521 Email: [email protected] Web: hubbellpowersystems.com
NOTES
1200 Gins-Booms_0320.indd 12061200 Gins-Booms_0320.indd 1206 3/16/20 2:44 PM3/16/20 2:44 PM
Gin
s a
nd
Bo
om
s –
12
00
Page 1207March 2020Phone: 573-682-5521 Email: [email protected] Web: hubbellpowersystems.com
NOTES
1200 Gins-Booms_0320.indd 12071200 Gins-Booms_0320.indd 1207 3/16/20 2:44 PM3/16/20 2:44 PM
Gin
s an
d B
oo
ms – 1
20
0
Page 1208 March 2020Phone: 573-682-5521 Email: [email protected] Web: hubbellpowersystems.com
NEVER COMPROMISE™
www.hubbellpowersystems.comMarch 2020 Catalog 1200
• 210 N. Allen St. • Centralia, MO 65240 • (573) 682-5521
NOTICE: For the latest revision of our Catalog and Literature, click here or visit our web site: www.hubbellpowersystems.com
NOTE: Hubbell has a policy of continuous product improvement. We reserve the right to change design and specifications without notice. ©Copyright 2020 Hubbell Incorporated
1200 Gins-Booms_0320.indd 12081200 Gins-Booms_0320.indd 1208 3/16/20 2:44 PM3/16/20 2:44 PM