warnings - hubbellcdn · hhh (modular highbay) installation instructions see warnings on carton...

WARNINGSObserve all precautions usually followed when dealing with high

voltage equipment when installing or servicing this light fixture.

• Disconnect power before installing or servicing.

• The product must be installed in accordance with the applicable

installation code by a person familiar with the construction and

operation of the product and the hazards involved.

• Protect all wiring connections with approved insulators rated 600V. 150ºC.

• Line voltage must be 120V – 277V to match fixture voltage requirement.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

• Upon receipt of this fixture, thoroughly inspect it for any damage.

If any is found, the carrier should be notified and held accountable.

TRIPLE H™

High Ambient High Output High Efficacy Highbay/Lowbay

Triple TM

http://www.hubbellindustrial.com/

http://www.hubbelllighting.com

INSTALLING HOOK/LOOP MOUNT (See Figure 1, 2, & 3):

NOTE: Cord and Hook/Loop ordered as CxHLPx(Plug optional and ordered separately)

1. Insert end of Power Cord (A) through Hook/Loop (B). Supply cord is to be rated for a minimum of 90OC 16/3 SEOW-A/STOOW.2. Insert end of Power Cord through the Cord Grip/Gotcha-ring (D),Rubber Bushing (E) and Washer (F). Note that the Rubber Bushing is placed between the Cord Grip and Washer. Part of the cord jacket should extend through Bushing (E) and Washer (F).3. Insert the Power Cord through the Yoke Assy Crossmember (C) and into the Wiring Box ¾ Conduit hole, allowing the Washer (F), Bushing (E) to “seat” inside. The Cord Grip (D) remains in place at the Hook/Loop.4. Apply Teflon tape to the male (external) conduit thread of the Hook (A).5. Thread the Hook (A) into the ¾” NPT Conduit Box (C). Use a wrench over the hex shape on the hook casting to tighten it in place. CAUTION: Do not twist the hook by using a screwdriver blade – too much force could break the hook.6. Connect cord wires to the fixture AC Power Input Jumper Cord Ass’y, already factory installed into J-box, with approved wire nuts. See wiring diagram for reference (page 3 and figure 6). Wires and wire nuts can now be pushed back into the fixture/driver housing. Ensure grounding wires within wiring Box are secure.7. Close out Wiring Box (G) using Cover, Cover Gasket, and Screws provided in hardware kit.8. Mount wired Yoke Assembly (H) onto fixture rails using 5/16” Screw (J) provided in hardware kit into each pair of Slide Nut (K) already inserted into the rail. Position the mounted Yoke Ass’y according to the centering illustration on page 10. Fine tuning of the final Yoke Ass’y position on the rail may be required to achieve final balance and alignment.9. Tighten the Yoke Ass’y mounting screws to torque noted in Fig. 3.10. Tighten Set Screw (F) to secure hook from loosening.11. Secure Closure Backet (M) with Screw (N) provided.12. Install lens option onto each Lightbar, see Figure 9. If wireguard was ordered, lenses will ship installed on fixture.13. Complete electrical connection by installing AC Input Jumper Cord connector into AC Panel as shown in Figure 3.

INSTALLATION INSTRUCTIONS

Hubbell Lighting, Inc. Doc. No. 93062486A subsidiary of Hubbell Incorporated Revision A701 Millennium Drive • Greenville, SC 29607 Phone (864) 678-1000Industrial Lighting

®

FIGURE 1FIGURA 1

FIGURE 3FIGURA 3

FIGURE 2FIGURA 2

PAGE 1

WIRING BOX3/4" OUTLETS(G)

5/16 MNTG SCREW (J)INTO RAIL SLIDE NUT (K)TORQUE: 120 IN-LB

HHH (MODULAR HIGHBAY) INSTALLATION INSTRUCTIONS

SEE WARNINGS ON CARTON

WARNINGS: Observe all precautions usually followed when dealing with high

voltage equipment when installing or servicing this light fixture. Disconnect power before installing or servicing. The product must be installed in accordance with the applicable

installation code by a person familiar with the construction and operation of the product and the hazards involved.

Protect all wiring connections with approved insulators rated 600V, 150OC.

Line voltage must be 120V – 277V to match Fixture voltage requirement.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE Upon receipt of this Fixture, thoroughly inspect it for any damage.


INSTALLING HOOK/LOOP MOUNT (See Figure 1, 2, & 3): NOTE: Cord and Hook/Loop ordered as CxHLPx (Plug optional and ordered separately)

1. Insert end of Power Cord (A) through Hook/Loop (B). Supply cord is to be rated for a minimum of 90OC 16/3 SEOW-A/STOOW.

2. Insert end of Power Cord through the Cord Grip/Gotcha-ring (D), Rubber Bushing (E) and Washer (F). Note that the Rubber Bushing is placed between the Cord Grip and Washer. Part of the cord jacket should extend through Bushing (E) and Washer (F).

3. Insert the Power Cord through the Yoke Assy Crossmember (C) and into the Wiring Box ¾ Conduit hole, allowing the Washer (F), Bushing (E) to “seat” inside. The Cord Grip (D) remains in place at the Hook/Loop.

4. Apply Teflon tape to the male (external) conduit thread of the Hook (A).

5. Thread the Hook (A) into the ¾” NPT Conduit Box (C). Use a wrench over the hex shape on the hook casting to tighten it in place. CAUTION: Do not twist the hook by using a screwdriver blade – too much force could break the hook.

6. Connect cord wires to the fixture AC Power Input Jumper Cord Ass’y, already factory installed into J-box, with approved wire nuts. See wiring diagram for reference (page 3 and figure 6). Wires and wire nuts can now be pushed back into the fixture/driver housing. Ensure grounding wires within wiring Box are secure.

7. Close out Wiring Box (G) using Cover, Cover Gasket, and Screws provided in hardware kit.

8. Mount wired Yoke Assembly (H) onto fixture rails using 5/16” Screw (J) provided in hardware kit into each pair of Slide Nut (K) already inserted into the rail. Position the mounted Yoke Ass’y according to the centering illustration on page 10. Fine tuning of the final Yoke Ass’y position on the rail may be required to achieve final balance and alignment.

9. Tighten the Yoke Ass’y mounting screws to torque noted in Fig. 3. 10. Tighten Set Screw (F) to secure hook from loosening. 11. Secure Closure Backet (M) with Screw (N) provided. 12. Install lens option onto each Lightbar, see Figure 9. If wireguard

was ordered, lenses will ship installed on fixture. 13. Complete electrical connection by installing AC Input Jumper

Cord connector into AC Panel as shown in Figure 3.

CLOSUREBRACKET (M)

RETAINING SCREW (N)

AFTER WIRINGASSEMBLE YOKE

TO FIXTURE USINGRAIL MOUNTINGHARDWARE KIT

- SEE FIG. 3

DE

FA

BYOKECROSSMEMBER

C

COMPLETEYOKE ASS'Y(H)

(CORDSETSNOT SHOWN)

FIGURE 1a.FIGURA 1a.

PLUG(OPTION AL)

CORDROUTE INTOJ-BOX WIRE TOAC INPUT JUMPER

LM

N


®

FIGURE 1FIGURA 1

FIGURE 3FIGURA 3

FIGURE 2FIGURA 2

PAGE 1
























CLOSUREBRACKET (M)

RETAINING SCREW (N)



- SEE FIG. 3

DE

FA

BYOKECROSSMEMBER

C


(CORDSETSNOT SHOWN)


PLUG(OPTION AL)


LM

N


®

FIGURE 1FIGURA 1

FIGURE 3FIGURA 3

FIGURE 2FIGURA 2

PAGE 1
























CLOSUREBRACKET (M)

RETAINING SCREW (N)



- SEE FIG. 3

DE

FA

BYOKECROSSMEMBER

C


(CORDSETSNOT SHOWN)


PLUG(OPTION AL)


LM

N

INSTALLING PENDANT MOUNT (See Figure 1, 3, 4, 5, & 6):

1. Install Locknut (Q) onto Pendent threads to the end of the threads.2. Apply Teflon tape to the male (external) conduit thread of the Pendent (P).3. Insert wiring from Pendent mounting conduit (P) into Wiring Box (G) of the Yoke Ass’y (H). Conduit end passes through the Yoke Assy Crossmember (C) and into the Wiring Box ¾ Conduit hole.4. Carefully thread the Yoke Ass’y onto the Pendent conduit (P) via Wiring Box. Use a wrench over the hex shape on the hook casting to tighten it in place. CAUTION: Do not twist the hook by using a screwdriver blade – too much force could break the hook.5. Connect cord wires to the fixture AC Power Input Jumper Cord Ass’y, already factory installed into J-box, with approved wire nuts. See wiring diagram for reference (page 3). Wires and wire nuts can now be pushed back into the fixture/driver housing. Ensure grounding wires within wiring Box are secure.6. Close out Wiring Box (G) using Cover, Cover Gasket, and Screws provided in hardware kit.7. Mount the fixture onto the Pendent mounted Yoke Assembly (H) via each rail using 5/16” Screw (J) provided in hardware kit into each pair of Slide Nut (K) already inserted into the rail. Position the mounted Yoke Ass’y according to the centering illustration on page 10. Fine tuning of the final Yoke Ass’y position on the rail may be required to achieve final balance and alignment.8. Tighten the Yoke Ass’y mounting screws to torque noted in Fig. 3.9. Install lens option onto each Lightbar, see Figure 9. If wireguard was ordered, lenses will ship installed on fixture.10. Complete electrical connection by installing AC Input Jumper Cord connector into AC Panel as shown in Figure 5.



®

FIGURE 5FIGURA 5

FIGURE 6FIGURA 6

PAGE 2

WIRINGBOX COVER

#8-32 SCREWS

LOCKNUT (Q)

YOKE ASSEMBLY (H)

3/4" CONDUITINLET INTO J-BOXSEAL WITH RTV AFTER INSTALL

PENDANT3/4" RIGID CONDUIT(P)






Protect all wiring connections with approved insulators rated 600V. 150OC.




INSTALLING PENDANT MOUNT (See Figure 1, 3, 4, 5, & 6): 1. Install Locknut (Q) onto Pendent threads to the end of the threads. 2. Apply Teflon tape to the male (external) conduit thread of the

Pendent (P). 3. Insert wiring from Pendent mounting conduit (P) into Wiring Box

(G) of the Yoke Ass’y (H). Conduit end passes through the Yoke Assy Crossmember (C) and into the Wiring Box ¾ Conduit hole.

4. Carefully thread the Yoke Ass’y onto the Pendent conduit (P) via Wiring Box. Use a wrench over the hex shape on the hook casting to tighten it in place. CAUTION: Do not twist the hook by using a screwdriver blade – too much force could break the hook.

5. Connect cord wires to the fixture AC Power Input Jumper Cord Ass’y, already factory installed into J-box, with approved wire nuts. See wiring diagram for reference (page 3). Wires and wire nuts can now be pushed back into the fixture/driver housing. Ensure grounding wires within wiring Box are secure.


7. Mount the fixture onto the Pendent mounted Yoke Assembly (H) via each rail using 5/16” Screw (J) provided in hardware kit into each pair of Slide Nut (K) already inserted into the rail. Position the mounted Yoke Ass’y according to the centering illustration on page 10. Fine tuning of the final Yoke Ass’y position on the rail may be required to achieve final balance and alignment.

8. Tighten the Yoke Ass’y mounting screws to torque noted in Fig. 3. 9. Install lens option onto each Lightbar, see Figure 9. If wireguard

was ordered, lenses will ship installed on fixture. 10. Complete electrical connection by installing AC Input Jumper Cord

connector into AC Panel as shown in Figure 5.

FIGURE 4FIGURA 4

J-BOXSEALINGGASKET

AC INPUT POWER CORDFROM WIRING J-BOXCONNECTED TO DRIVERMODULE.

FACTORY WIREDAC INPUT CORD

FROM J-BOX - CONNECTTO AC INPUT PANELON DRIVER MODULE


®

FIGURE 5FIGURA 5

FIGURE 6FIGURA 6

PAGE 2

WIRINGBOX COVER

#8-32 SCREWS

LOCKNUT (Q)

YOKE ASSEMBLY (H)

3/4" CONDUITINLET INTO J-BOXSEAL WITH RTV AFTER INSTALL

PENDANT3/4" RIGID CONDUIT(P)










INSTALLING PENDANT MOUNT (See Figure 1, 3, 4, 5, & 6): 1. Install Locknut (Q) onto Pendent threads to the end of the threads. 2. Apply Teflon tape to the male (external) conduit thread of the

Pendent (P). 3. Insert wiring from Pendent mounting conduit (P) into Wiring Box

(G) of the Yoke Ass’y (H). Conduit end passes through the Yoke Assy Crossmember (C) and into the Wiring Box ¾ Conduit hole.

4. Carefully thread the Yoke Ass’y onto the Pendent conduit (P) via Wiring Box. Use a wrench over the hex shape on the hook casting to tighten it in place. CAUTION: Do not twist the hook by using a screwdriver blade – too much force could break the hook.

5. Connect cord wires to the fixture AC Power Input Jumper Cord Ass’y, already factory installed into J-box, with approved wire nuts. See wiring diagram for reference (page 3). Wires and wire nuts can now be pushed back into the fixture/driver housing. Ensure grounding wires within wiring Box are secure.


7. Mount the fixture onto the Pendent mounted Yoke Assembly (H) via each rail using 5/16” Screw (J) provided in hardware kit into each pair of Slide Nut (K) already inserted into the rail. Position the mounted Yoke Ass’y according to the centering illustration on page 10. Fine tuning of the final Yoke Ass’y position on the rail may be required to achieve final balance and alignment.

8. Tighten the Yoke Ass’y mounting screws to torque noted in Fig. 3. 9. Install lens option onto each Lightbar, see Figure 9. If wireguard

was ordered, lenses will ship installed on fixture. 10. Complete electrical connection by installing AC Input Jumper Cord

connector into AC Panel as shown in Figure 5.

FIGURE 4FIGURA 4

J-BOXSEALINGGASKET

AC INPUT POWER CORDFROM WIRING J-BOXCONNECTED TO DRIVERMODULE.

FACTORY WIREDAC INPUT CORD

FROM J-BOX - CONNECTTO AC INPUT PANELON DRIVER MODULE


®

PAGE 3

FIGURE 7FIGURA 7

FIGURE 9FIGURA 9











INSTALLING AIRCRAFT CABLE MOUNTING SYSTEM (See Figure 7 and 8):

WARNING! NOTICE AIRCRAFT CABLE KIT TYPE SHIPPED WITH YOUR ORDER: 2mm KIT FOR LOWBAY SERIES ONLY! 3mm KIT FOR HIGHBAY SERIES ONLY!

1. Install AC Mounting Bracket (R) onto each corner of the rail, inset approximately 1-inch from the rail end. Using 5/16” Screw (J) provided in the hardware kit, insert the screw through the bottom hole of each backet and install into the Slide Nut (K) pre-installed within the rail. Ensure the bracket when pre-tightened is vertically oriented as shown in Figure 8.

2. Tighten AC Mounting Bracket Screw (J) to torque noted in Fig. 8, while supporting the bracket orientation to prevent rotating during the tightening sequence.

3. Insert each Snap Hook Eyelet of the Y-Cable Ass’y onto the AC Mounting Bracket top holes on each end of the fixture so that the cable spans across the lightbar as shown in Figure 7.

4. The Top Cable of the Aircraft System is lopped around a facility structural member suitable to support the fixture load. The bare cable end being inserted into the Top Cable Loop and then proceeding into the Gripper. The Top Cable length should be adjusted to desired length according to mounting height selected).

5. Repeat for other side of the fixture cable mounting. 6. Final adjustment of the Gripper Barrel position across the width of

the fixture will balance the fixture, while Top Cable Length adjustment will balance the fixture lengthwise. See Figure 7 illustration.

7. Install lens option onto each Lightbar, see Figure 9. If wireguard was ordered, lenses will ship installed on fixture.

8. Complete electrical connection by installing AC Input Cord into AC Panel as shown in Figure 10.

AIRCRAFT CABLE KIT( 2mm KIT FOR LB, 3mm KIT FOR HB)

FIGURE 8FIGURA 8

ACRYLIC LENS: SNAP INTO LIGHTBAR GROOVE

AIRCRAFTMNTG OPTIONBRACKET (R)


FIGURE 10FIGURA 10


WARNING! NOTICE AIRCRAFT CABLE KIT TYPE SHIPPEDWITH YOUR ORDER:2mm KIT FOR LOWBAY SERIES ONLY!3mm KIT FOR HIGHBAY SERIES ONLY!

1. Install AC Mounting Bracket (R) onto each corner of the rail, inset approximately 1-inch from the rail end. Using 5/16” Screw (J) provided in the hardware kit, insert the screw through the bottom hole of each backet and install into the Slide Nut (K) pre-installed within the rail. Ensure the bracket when pre-tightened is vertically oriented as shown in Figure 8.2. Tighten AC Mounting Bracket Screw (J) to torque noted in Fig. 8, while supporting the bracket orientation to prevent rotating during the tightening sequence.3. Insert each Snap Hook Eyelet of the Y-Cable Ass’y onto the AC Mounting Bracket top holes on each end of the fixture so that the cable spans across the lightbar as shown in Figure 7.4. The Top Cable of the Aircraft System is lopped around a facility structural member suitable to support the fixture load. The bare cable end being inserted into the Top Cable Loop and then proceeding into the Gripper. The Top Cable length should be adjusted to desired length according to mounting height selected).5. Repeat for other side of the fixture cable mounting.6. Final adjustment of the Gripper Barrel position across the width of the fixture will balance the fixture, while Top Cable Length adjustment will balance the fixture lengthwise. See Figure 7 illustration.7. Install lens option onto each Lightbar, see Figure 9. If wireguard was ordered, lenses will ship installed on fixture.8. Complete electrical connection by installing AC Input Cord into AC Panel as shown in Figure 10.



®

PAGE 3

FIGURE 7FIGURA 7

FIGURE 9FIGURA 9






















FIGURE 8FIGURA 8




FIGURE 10FIGURA 10


®

PAGE 3

FIGURE 7FIGURA 7

FIGURE 9FIGURA 9






















FIGURE 8FIGURA 8




FIGURE 10FIGURA 10


®

PAGE 3

FIGURE 7FIGURA 7

FIGURE 9FIGURA 9






















FIGURE 8FIGURA 8




FIGURE 10FIGURA 10

Hubbell Lighting, Inc.A subsidiary of Hubbell Incorporated701 Millennium Drive • Greenville, SC 29607Industrial Lighting

®

PAGE 4HHH WIRING DIAGRAMS

GROUNDGREEN

LINE(HOT) BLACK

BLACK

WHITE

RED

RED

WHT

BLK

FUSING

WIHUBB OPTION(ETO ONLY)

FUSING

SINGLE FUSEOPTION

DOUBLE FUSEOPTION

OCCUPANCY SENSOR(OCS) OPTION

RED

WHT

BLK

SURGESUPPRESSOR

CONTROL SENSOR (WST) (ETO ONLY)

WIRELESS CONTROL DEVICE(WIS) OPTION

WHITE

BLACK

DC INPUTPANEL CONNECTORLIGHTBAR

+-

+-

DC OUTPUTPANEL CONNECTORFROM DRIVER MDL

INTERCONNECT CORDSET ASSY'S90° HEAD BOTH ENDS - MALE PINS ON DRIVER OUTPUT, FEMALE END TOWARDS LIGHTBAR)

DRVR

RED

BLUE

RED

BLUE

BRWN

BLUE

BRWN

BLUE

RED

WHT

BLK

GREENBLACKWHITE

Doc. No. 93062486Revision APhone (864) 678-1000

HHH MODULAR LOWBAY LOW OUTPUT ASSEMBLYWIRING DIAGRAM "LOWBAY TWIN"

HHH-xK-LB-LO

WIRING DIAGRAMS


HHH (MODULAR HIGHBAY)INSTALLATION INSTRUCTIONS

Hubbell Lighting, Inc. Doc. No. 93062486A subsidiary of Hubbell Incorporated Revision C701 Millennium Drive • Greenville, SC 29607 Phone (864) 678-1000Industrial Lighting

®

PAGE 1

SEE TABLEBELOW

FIGURE 11FIGURA 11

HHH (MODULAR HIGHBAY) - LOOSE DIMMING LEADS WIRING TO HOUSE SUPPLY

Item Service/Repl Part Nr(incl. packaging)

Light Engines15‐inch LED boards 5K 9307503226‐inch LED board 5K 9307503315‐inch LED boards 4K 9307503426‐inch LED board 4K 93075035

Drivers 95W Driver 120‐277V 9307503650W Driver 9307503795W Driver 347‐480V 93075038

Lenses15‐Inch di ffuse 9307504326‐inch di ffuse 9307504415‐inch medium 9307504526‐inch medium 9307504615‐inch narrow 9307504726‐inch narrow 9307504815‐inch wide 9307504926‐inch wide 93075050

Wire Guard15‐inch flat 9307505126‐inch flat 9307505215‐inch Round 9307505426‐inch Round 9307505515‐inch flat 9307727026‐inch flat 9307727115‐inch Round 9307727226‐inch Round 93077273

HHH REPLACEMENT PARTS

Dimming ConnectionColor Code Matrix

House Supply Lead Colors Positive (+) Negative (‐)

Violet (positive +) Violet ‐Gray (negative ‐) ‐ Gray

Violet (positive +) Brown ‐Gray (negative ‐) ‐ Blue

Fixture Dimming Cable Lead Colors

Alternate

Default

DIMMING CONNECTIONS BY COLOR CODEHHH (MODULAR HIGHBAY)INSTALLATION INSTRUCTIONS


®

PAGE 1

SEE TABLEBELOW

FIGURE 11FIGURA 11













Alternate

Default

DIMMING CONNECTIONS BY COLOR CODE



®

PAGE 1

SEE TABLEBELOW

FIGURE 11FIGURA 11













Alternate

Default




®

PAGE 1

SEE TABLEBELOW

FIGURE 11FIGURA 11













Alternate

Default




®

PAGE 1

SEE TABLEBELOW

FIGURE 11FIGURA 11













Alternate

Default


WIRING DIAGRAMS


®



GROUNDGREEN

LINE(HOT) BLACK

COMMON(NEUTRAL) WHITE

BLACK

WHITE

RED

FUSING

FUSING

SINGLE FUSEOPTION

DOUBLE FUSEOPTION

SURGESUPPRESSOR

HHH MODULAR LOWBAY HIGH OUTPUT ASSEMBLYWIRING DIAGRAM "LOWBAY QUAD"

HHH-xK-LB-HO





+-

+-

+-



INTERCONNECT CORDSET ASSY90° HEAD BOTH ENDS - MALE PINS ON DRIVER OUTPUT, FEMALE END TOWARDS LIGHTBAR)

WHITE

BLACK

DRVR

DRVR

BRWN

BLUE

BRWN

BLUE

BRWN

BLUE

BRWN

BLUE

RED

BLUE

RED

BLUE

RED

BLUE

RED

BLUE

WHITE

BLACK

WHITE

BLACK

RED

WHT

BLK

RED

WHT

BLK

RED

WHT

BLK

GREENBLACKWHITE


®



GROUNDGREEN

LINE(HOT) BLACK


BLACK

WHITE

RED

RED

WHT

BLK

FUSING

FUSING

SINGLE FUSEOPTION

DOUBLE FUSEOPTION

SURGESUPPRESSOR GREEN

BLACKWHITE

HHH MODULAR LOWBAY MEDIUM OUTPUT ASSEMBLYWIRING DIAGRAM "LOWBAY TRIO"

HHH-xK-LB-MO





+-

+-

+-



INTERCONNECT CORDSET ASSY'S90° HEAD BOTH ENDS - MALE PINS ON DRIVER OUTPUT, FEMALE END TOWARDS LIGHTBAR)

WHITE

BLACK

DRVR

DRVR

BRWN

BLUE

BRWN

BLUE

BRWN

BLUE

RED

BLUE

RED

BLUE

RED

BLUE

WHITE

BLACK

WHITE

BLACK

RED

WHT

BLK

RED

WHT

BLK

WIRING DIAGRAMS


®



GROUNDGREEN

LINE(HOT) BLACK


BLACK

WHITE

RED

FUSING

FUSING

SINGLE FUSEOPTION

DOUBLE FUSEOPTION

SURGESUPPRESSOR

HHH MODULAR HIGHBAY LOW OUTPUT ASSEMBLYWIRING DIAGRAM "HIGHBAY TWIN"

HHH-xK-HB-LO





+-

+-




WHITE

BLACK

DRVR

DRVR

BRWN

BLUE

BRWN

BLUE

RED

BLUE

RED

BLUE

WHITE BLACK

WHITE

BLACK

WHITE

BLACK

RED

WHT

BLK

RED

WHT

BLK

RED

WHT

BLK

GREENBLACKWHITE


®



GROUNDGREEN

LINE(HOT) BLACK


BLACK

WHITE

RED

FUSING

FUSING

SINGLE FUSEOPTION

DOUBLE FUSEOPTION

SURGESUPPRESSOR

HHH MODULAR HIGHBAY MEDIUM OUTPUT ASSEMBLYWIRING DIAGRAM "HIGHBAY TRIO"

HHH-xK-HB-MO





+-

+-

+-

DC INPUTPANEL CONNECTORLIGHTBARDC OUTPUT

PANEL CONNECTORFROM DRIVER MDL


DRVR

DRVR

DRVR

BRWN

BLUE

BRWN

BLUE

BRWN

BLUE

RED

BLUE

RED

BLUE

RED

BLUE

WHITE BLACK

WHITE

BLACK

WHITE

BLACK

WHITE

BLACK

RED

WHT

BLK

RED

WHT

BLK

RED

WHT

BLK

GREENBLACKWHITE

WIRING DIAGRAMS


®

PAGE 9


WHITE

HHH-xK-LB-LO & HHH-xK-HB-LO UNITSCENTERED ON RAIL

NOMINAL YOKE INSTALL POSITION BY FIXTURE TYPE:Final installation position may vary to balance fixture in positiom

HHH-xK-LB-MO & HHH-xK-HB-MO UNITSPOSITIONED AS SHOWN OVER FIRST LIGHTBAR

HHH-xK-LB-HO & HHH-xK-HB-HO UNITSCENTERED ON RAIL

7.26.4 10.1

HIL_0137_HHH_INST


®



GROUNDGREEN

LINE(HOT) BLACK


BLACKWHITE

RED

FUSING

FUSING

SINGLE FUSEOPTION

DOUBLE FUSEOPTION

SURGESUPPRESSOR

HHH MODULAR HIGHBAY HIGH OUTPUT ASSEMBLYWIRING DIAGRAM "HIGHBAY QUAD"

HHH-xK-HB-HO





+-

+-

+-

+-




WHITE BLACK

DRVR

DRVR

DRVR

DRVR

BRWN

BLUE

BRWN

BLUE

BRWN

BLUE

BRWN

BLUE

RED

BLUE

RED

BLUE

RED

BLUE

RED

BLUE

WHITE

BLACK

WHITE

BLACK

WHITE

BLACK

WHITE

BLACK

RED

WHT

BLK

RED

WHT

BLK

RED

WHT

BLK

GREENBLACKWHITE

http://www.hubbelllighting.com

warnings - hubbellcdn · hhh (modular highbay) installation instructions see warnings on carton...

Documents