vortex partfill - jobevalves.com · vortex part fill is a high flow valve intended for use in rain...
TRANSCRIPT
© Jobe Valves P.O Box 17 Matamata New Zealand P: +64 (0)7 880 9090 F: +64 (0)7 880 9099 E: [email protected] W: www.jobevalves.com
Description
ApplicationsMaintaining water levels in:• Rain water harvesting tanks• Water cisterns• Irrigation and process applications.
Features• Ideal for use with all makes and models of rain water harvesting tanks• Compact• Constructed from non corroding materials• Valve can be locked in off position using the lock off switch• Up to 150mm differential obtainable (dependant on pressure)• Valve unscrews from tail for easy Valve Access.
Available Inlet SizesVXVP32 32mm (1 ¼”)VXVP40 40mm (1 ½”)VXVP50 50mm (2”)VXVP114 1 ¼” NPTVXVP112 1 ½’’ NPTVXVP2 2” NPT
Vortex Part Fill is a high flow valve intended for use in rain water harvesting tanks. The purpose of the float valve is to automatically maintain a low level of water in the tank during periods of no or low rainfall. This allows services fed by the tank to continue while leaving capacity in the tank for refilling by the next rain.
Principle of Operation• The Valve is installed through the side wall of a storage tank. It should be mounted above the overflow level of the tank to prevent backflow.
• As the tank empties the weighted float travels down the cord and sits on the bottom stop to activate the valve.
• The valve will run until the weighted float lifts clear of the bottom stop.
• The float will then rise as rainwater fills the tank and falls as the tank water is used.
• The Valve will only function at times when rain fall is insufficient to maintain a water level in the tank above the bottom stop.
Pressure Range0.3 Bar – 10 Bar (5 psi-150 psi)
1.5
1.0
0.5
0 100 200 300 400 500 600 700
2.0
2.5
Flow LPM
Imperial GPM
Inle
t Pre
ssur
e B
ar
20 40 60 80 100 120 140
35
30
25
20
15
10
5
PS
I
Flow Graph( All Sizes )
Vortex Partfill Operating Zone
Typical Installaton
Rain Water Filling Zone
60
0 L
/ M
INMains or pump supplied water inlet
Weighted Float able to float freely up and down cord
Rainwater Inlet
Air Break
Cord
Weighted Float
Rainwater Inlet
3.13
VORTEX PARTFILL PRODUCT INFO
Vortex Dimensions
60
0 L
/ M
IN
4 ¼”
108mm
1 7/16”
31mm
1 9/
16”
40
mm
2 7/
16”
65
mm
10 11/16”
270mm
Valve Body
White Internal Parts
Arm Assembly
Diaphragm
GF Nylon
Acetal
ABS
EPDM
Seal
Springs, Bolts, Nuts, Pin, Screws
O’Rings
Float
TPU
304 Stainless Steel
Nitrile
HDPE
MaterialPart MaterialPart
Float &Weight
Dimensions
2 7/16” 65mm
8 3/
16”
208m
m
¾”
20m
m
4 ⅜
” 11
0mm
60ºC, 140ºFMaximum Operating Temperature
© Jobe Valves P.O Box 17 Matamata New Zealand P: +64 (0)7 880 9090 F: +64 (0)7 880 9099 E: [email protected] W: www.jobevalves.com3.14
VORTEX PARTFILL DIMENSIONS & MATERIALS
2 DESCRIPTION CODE
1
2
3
4
5
6
7
8
9
10
VXPP2010
VXP2020
VXP2030
VXP2040
VXPP2050
VXPP2060
VXP2080
VXP2090
VXP2100
VXP2110
Actuator Cap6g x 10 S/S Screw Frost Pro Plug Frost Pro O’ring Valve Cap Assembly Damping Spring Bearings (set of two) Actuator Arm Bolt M6 x 65Washer M6 x 12.5
1
2
1 4
3
4
1
DESCRIPTIONCODE
3
2
CODE: VXVP
1
2
3
4
5
VXPP1010
VXPP1020
VXPP1030
VXPP1040
VXPP1050
Bottom Stop
Weighted Float
Cord
Arm Extension
M5 x 12 Bolt
1
2
3
4
VXPP1
VXPP2
VXP3
Float Assembly
Cap & Actuator Assembly
Diaphragm Assembly
Base Assembly
DESCRIPTION CODE
2
3
4
DESCRIPTION CODE 4Vortex Retainer
Vortex Base
Vortex O’ring
Vortex Tail 32mm
Vortex Tail 40mm
Vortex Tail 50mm
Vortex Tail 1 ¼” NPT
Vortex Tail 1 ½” NPT
Vortex Tail 2” NPT
1
2
3
4
VXP4010
VXP4020
VXP4030
VXP4040
VXP4045
VXP4050
VXP4055
VXP4060
VXP4065
1
5
60
0 L
/ M
IN
1
23
45
89
10
6
7
3
DESCRIPTION CODE
1
2
VXP3
TPP3010
TPP3011
Diaphragm Assembly
Pilot Flow Filter (Fine)
Pilot Flow Filter (Coarse)
1
2
© Jobe Valves P.O Box 17 Matamata New Zealand P: +64 (0)7 880 9090 F: +64 (0)7 880 9099 E: [email protected] W: www.jobevalves.com 3.15
VORTEX PARTFILL PARTS IDENTIFICATION SHEET