volume iiiengineeringprojects.com/tender/uploadfiles/3458_vol-iii.pdf · 2018-07-27 · providing...
TRANSCRIPT
ANISO9001&14001COMPANY
TENDER DOCUMENT
TENDER No: DLI/CON/755/612 dated 17.01.2018
FOR
Tender for “Phase-II works of Repair, renovation & Face Lifting of STPI Building at Borjhar, Guwahati”
VOLUME–III
Price bid/Bill of Quantity
A Civil Works
B Sanitary installation and Water supply
C Electrical Works
i Internal Electrical Works
ii External Electrical Works
D Other Ancillary Works
1 HVAC
2 Iron Removal filter
3 Land Scaping/ Horticulture
4 Fire Detection System
5 Fire Fighting System
6 Interior and Allied works
7 STPI Owned Furnitures
8 STPI Owned Chairs
9 CCTV Camera
10 Structured Cabling
Total (A+B+C+ D)
Phase-II works of Repair, Renovation and Face-lifting of STPI building at
Borjhar, Guwahati.
Sl. No. PARTICULARS AMOUNT (RS)
FINANCIAL BID (ABSTRACT OF COST)
Page 1 of 79
1
cu-m 625.06
2 cu-m 688.00
3
cu-m 320.45
4
cum 412.13
5 cum 945.47
6
Cum 21.23
cum 21.80
Cum 12.00
8 sqm 0.00
9 Sqm 114.78
Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas
(exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of
excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.
All kinds of soil
Extra for every additional lift of 1.5 m or part thereof in excavation/ banking excavated or stacked
materials.
Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in
layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering,
lead up to 50 m and lift upto 1.5 m.
EARTHWORK IN EXCAVATION
Earth work in excavation by mechanical means (Hydraulic excavator / manual means in foundation
trenches or drains (not exceeding 1.5 m in width or 10 Sqm on plan), including dressing of sides and
ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus
excavated soil as directed, within a lead of 50m.
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating
and dressing complete.
CEMENT CONCRETE WORKS
Providing and laying in position cement concrete of specified grade excluding the cost of centering
and shuttering - All work up to plinth level :
BOQ FOR CIVIL WORK Sl.
No.Description Unit
REINFORCEMENT CEMENT CONCRETE
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20mm nominal size).
All kinds of soil
All kinds of soil.
1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size).
1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size).
DAMP- PROOF COURSE
Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 12.5 mm nominal size
Rate (Rs.) Amount (Rs.) Quantity
PAGE 2 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
10
cum 207.17
cum 133.48
11
Sqm 25.88
12 cum 58.73
SqM 10.00
13
Sqm 711.38
14
All works upto plinth level
All works above plinth level upto floor V level
Providing and laying in position machine batched and machine mixed design mix M-25 grade
cement concrete for reinforced cement concrete work, using cement content as per approved design
mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering,
finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to
accelerate, retard setting of concrete, improve workability without impairing strength and durability
as per direction of Engineer-in-charge. (Using M25 or Equivalent nominal mix 1:1:2)
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15°
landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair
cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing
and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20
mm nominal size).
WATER PROOFING TREATMENT AT TERRACE, TOILET'S FLOOR AND WALL
Water proofing on roof slab with 10 years guarantee, also porch slab.
Providing and laying integral cement based water proofing treatment including preparation of
surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:
a) Applying a slurry coat of neat cement using 2.75 Kg/Sqm of cement admixed with water proofing
compound conforming to IS. 2645...........as directed and specified by the Engineerin- Charge :
Providing precast R.C.C slab over drain ,septic tank etc. in prop. 1:2:4 reinforced with 10mm M.S.
bar @ 150mm centre both ways tying with 20 gauge black annealed wire with necessary shuttering ,
curing etc. complete including fixing in position as directed.
ANTI TERMITE TREATMENTPre construction anti - termite treatment at the bottom of foundation pits and walls on either side up
to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches
etc. by applying the emulsion @ 5 (five) litres per square meter of the surface area before starting
construction work (supplying of necessary tools and accessories by the contractor) as per the
direction of the Department complete.
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of
centering, shuttering, finishing and reinforcement - All work up to plinth level :
1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone
PAGE 3 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Sqm. 10.80
Sqm. 10.80
15
Rm 200.00
Rm 825.00
Sqm 825.00
Rm 300.00
Rm 42.40
16
each 100.00
Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or
kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45
degree at 150 mm centre to centre andsealing the same.
POST CONSTRUCTION ANTI - TERMITE TREATMENT
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment
(excluding the cost of chemical emulsion) :
Expansion Joint Filler Board
Providing fitting & fixing CI Grating to the floors complete as directed and specified
With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per
linear metre including drilling and plugging holes etc.:
With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300
mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2
(1 cement : 2 Coarse sand) to match the existing floor:
With Chlorpyriphos/Lindane E.C. 20% with 1%concentrationTreatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval
including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse
sand) to the full depth of the hole :
a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or
euivalent) and water, i.e. 1% solution.
b) with aqueous emulsion having concentration 1:499 with Premise 350 SC (Imidachloprid 30.5%
SC) and water, i.e. 0.07% solution.
Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of
the vertical surface of the substructure to a depth of 300 mm including excavation channel along the
wall & rodding etc. complete:
With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration
(a)80mm dia
GRATING
PAGE 4 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
17
RM 2.00
18
Rm 30.00
19
Rm 32.00
20
sq-m 69.68
309.93
21
Sqm 1135.35
Sqm 445.64
Centering and shuttering including strutting, propping etc. and removal of form work for (PCC) :
Foundations, footings, bases for columns
Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth
and string courses fillets,kerbs and steps etc.
Providing and fixing Duraboard HD-100 premoulded compressible filler board at all heights and
depths of minimum density 95Kg/cum, non-staining having less than 1% water absorption,
compression recovery of 93% (minimum) as per manufactured specification with polysulphide
sealant to seal the expansion joint including preparation of surface, Polymer Modified Mortar
(PMM) (Proportion 1cement: 3 sand:1 acrylic polymer) nozing, carriage all levels as per drawings
and direction of Engineer-in-Charge.
(d ) 50mm wide
Columns, Pillars, Piers, Abutments, Posts and Struts
Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for
expansion joints.
200 mm wide.TREATMENT OF EXPANSION JOINTS
SHUTTERING FORMWORKS
Centering and shuttering including strutting, propping etc. and removal of form for :
Suspended floors, roofs, landings, balconies , lintel , beam and access platform
Providing treatment of expansion joints by the following process as specified and directed by the
department. Parachange
(a) Preparation of groove by nosing the groove in required sizes with Polymer modified mortar -
Cement sand mortar (in prop 1:3) mixed with Master Crete M-81 of Choksey Chemicals /Dr. Sealkit
Sealcrete (Asian Chemicals) /Rheomix 115 of BASF@ 15% by weight of cement over a bonding
coat of Master Crete M-81/Rheomix 131 of BASF mixed with cement in the ratio 1:2 as specified &
directed by the Department complete after proper surface preparation including cleaning/ chipping
removing all sorts of loose particles and foreign materials and cleaning surface thoroughly (surface
preparation including thorough cleaning of surface to be measured and paid separately).
(b) Providing and applying two coat of Techseal RDL 942 Primer in both surface of the expansion
joint followed by applying Tech seal 940 Polysulphide sealant on vertical joint surface after proper
fixing of the necessary backup materials as specified and directed by the Department complete.
PAGE 5 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Sqm 535.65
Sqm 180.77
22
Sqm 0.00
Sqm 281.05
Cum 15.00
cum 142.39
24
Sqm 0.00
25
Sqm 39.00
23 Providing brick soiling in foundation and under floor with stone/best quality picked jhama brick,
sand packed and laid to level and in panel after preparing the subgrade as directed including all
labour and materials and if necessary dewatering complete.
(a)Brick on flat soling Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in
foundation and plinth in:
Cement mortar 1:6 (1 cement : 6 coarse sand)
Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand
packed and laid to level and in panel after preparing the subgrade as directed including all labour
and materials and if necessary dewatering, complete.(a)Brick on flat soling.( at footing bed)
Half brick masonry with non modular fly ash bricks of class designation 10, conforming to IS :
12894, in super structure above plinth and upto floor V level.
SCAFFOLDING
Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12 mm thick
Lintels, beams, plinth beams, girders, bressumers andcantilevers. with water proof ply 12 mm thick
(b) In proportion 1:4 (1 cement:4 sand)
ROOF TRUSS
BRICK WORKS
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level in all shapes and sizes in :
Cement mortar 1:6 (1 cement : 6 coarse sand)
Providing and fixing double scaffolding system (cup lock type) on the exterior side of
building/structure, upto 25 metre height, above ground level, including additional requirement of
site, made with 40mm dia M.S. tube, placed 1.5 metrerows of scaffolding in stepped manner as per
centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S.
tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and
maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or
applying chemical and removing it thereafter. The scaffolding system shall be stiffened with
bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of
work at required locations with essential safety features for the workmen etc., complete as per
directions and approval of Engineer-in-charge
PAGE 6 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
26
Kg 3987.00
27
sq-m 55.00
Sqm 297.60
28
metre 10.80
29
Kg 51185.29
30
Kg 950.00
Kg 200.00
31
Sqm 12.00
In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
FLY PROOF MS WIRE NET
Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat
15x3 mm and nuts & bolts complete.
Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides
ROOFING SHEET
Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer
coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I.
limpet washers filled with white lead, including a coat of approved steel primer and two coats of
approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved
surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape
wherever required
0.80 mm thick with zinc coating not less than 275 gm/m²
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position
and binding all complete upto .and above plinth level
IRON & STEEL WORK:
RAILING
In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required,
all complete
1.00 mm thick with zinc coating not less than 275 gm/m²
Providing ridges or hips of width 60 cm overall width plain G.S. Sheet fixed with polymer coated J.
or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.
0.63 mm thick with zinc coating not less than 275 gm/m²
MS FRAME FOR FLY PROOF NET
Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position
and applying a priming coat of approved steel primer using structural steel etc. as required.
Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including
cutting, hoisting, fixing in position and applying a priming coat of .approved steel primer, including
welding and bolted with special shaped washers etc. complete.
Electric resistance or induction butt welded tubes
Thermo-Mechanically Treated bars
PAGE 7 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
32
Kg 1105.09
SS Railing32A
Kg 1125.00
MS Grill
33
Sqm 1.20
34
Sqm 1.68
35
kg 2683.46
36
STRUCTURAL STEEL
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work,
including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer
all complete.
Providing and fixing Stainless Steel (Grade 304) railing made of hollow
tubes, channels, plates etc., including welding, grinding, buffing, polishing
and making curvature(wherever required) and fitting the same with
necessary stainless steel nuts and bolts complete, i.e. fixing the railing
with necessary accessories & stainless steel dash fasteners, stainless steel
bolts etc., of required size, on the top of the floor or the side of waist slab
with suitable arrangement as per approval of engineer in charge.(For
payment, only weight of stainless steel member is to be considered. No
extra payment for fixing accessories such as nuts, bolts, fasteners etc. will
be considered)
30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats,
square or round bars etc. including priming coat with Fixed to openings /wooden frames with rawl
plugs screws etc.
Fixed to openings /wooden frames with rawl plugs screws etc.
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type,
core of block board construction with frame of 1st class hard wood and well matched teak 3 ply
veneering with vertical grains or cross bands and face veneers on both faces of shutters
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony
railing, staircase railing and similar works, including applying priming coat of approved steel primer
M.S. tube
STEEL T-IRON FRAME
Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections,
joints mitred and welded, including fixing of necessary butt hinges and screws and applying a
priming coat of approved steel primer.
PAGE 8 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Kg 25.00
37
Sqm 3.00
38 Sqm 1273.17
39
Sqm 615.51
40
Sqm 288.00
41
cum 78.75
42
12 mm thick
Stone Soaling
Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand
packed and laid to level and in panel after preparing the subgrade as directed including all labour
and materials and if necessary dewatering, complete.
(c).Stone soling of thickness 150mm.X 3 layer
15 mm cement plaster 1:2 (1 cement : 2 stone dust) on the rough side of single or half brick wall.
© In cement mortar 1:6
CEMENT PLASTER
18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse
sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with
sponge.
Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F
Suspended Ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange
of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw
fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then
suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm
each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed
to soffit with G.I.cleat and steel expansion fasteners.
FALSE CEILING
Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating
coat of neat cement
Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C.
1:3:6 (1 Cement : 3 coarse
sand : 6 graded stone aggregate 20 mm nominal size)
Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm
M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a
priming coat of approved steel primer.
Using flats 30x6mm for diagonal braces and central cross piece
PAGE 9 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Sqm 522.00
43
Sqm 102.60
Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm
each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip
and in direction perpendicular to the intermediate channel at 457mm c/c, 9.5mm/ 12.5mm tapered
edge Gypboard (conforming to IS:2095-1982) is then screw fixed to ceiling section with 25mm long
drywall screws at 230mm c/c. Screw fixing is done mechanically either with screw driver or drilling
machine with suitable attachment. Finally, the boards are to be jointed and finished so as to have a
flush look which includes filling and finishing the tapered and square edges of the boards with
jointing compound, joint paper tape and two coats of drywall topcoat suitable for Gypboard
complete at all levels as specified and directed. (For light fittings, providing opening for doors,
window, ventilators etc, cut out made with frame of perimeter channel supported suitably to be
measured and paid separately where necessary).
9.5mm thick
Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal
level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @
120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get
required length and of size 24x38 mm made from 0.30 mm thick(minimum) sheet, spaced at 1200
mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200
mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and
secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet
to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle
of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including,
required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke
detectors etc. Main “T” runners to be mm fixed to ceiling with 12.5 mm dia and 50 mm long dash
fasteners, 4 suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm GI
adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm
center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted
with polyester paint, all complete for all heights as per specifications, drawings and as directed by
Engineer-in-charge.
8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials
reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline
structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of
size 595x595 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation
of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having
an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing.
PAGE 10 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
44
Sqm 744.42
45
Sqm 531.90
46
Sqm 68.96
47
Sqm 122.00
48 FALSE FLOORING AT SWITCH ROOM, CONTROL ROOM
38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to
be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45
Kg per Sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half
depth, planed, levelled smooth and finished complete.
WOODEN FLOORING,
Providing and fixing false ceiling at all height including providing and fixing of frame work made of
special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/Sqm
(both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm
thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling
with dash fastener 12.5 mm dia x 50mm long with 12.5mm thick 6mm dia bolts, other flange of
cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required
size and other end of at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5
mm thick bottom wedge of 80 mm with tapered flanges of 26 mm Each having lips of 10.5 mm, at
450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with
connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including
12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I.
Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal
level suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @
120 gsm/sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and
0.5 mm thick with 8mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides
inclusive) and 20% perforation area with 1.8mm dia holes and having NRC (Noise Reduction
Coefficient ) of 0.5, electro statically polyester powder coated of thickness60 microns (minimum),
including factory painted after bending and perforation, and backed with a black Glass fiber
acoustical fleece.
FLOOR FINISHED
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished,
machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of
required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1
cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy
touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc.
complete at all levels
Area of slab over 0.50 Sqm
PAGE 11 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Sqm 110.00
49
Sqm 75.00
50
Sqm 173.73
51
52
Sqm 55.00
53
Sqm 165.00
54
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a
floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc.
complete.
40 mm thick with 20 mm nominal size stone aggregate
IPS FLOOR
Providing and laying Imported Loop pile patterned carpet 24-26 OZ. in Roll/Tile form (Available
tile sizes 900mm x 900mm / 450mm x 450mm) with antistatic rating of <3.5, PVC/ Eco-friendly
backing and having guage of 1/10- 1/12 as per the selection of the architect. Carpet to be of pile
composition of Nylon of Dupont / Deftron / Colorfast / Wearon or other equivalent make confirming
to relevant BS standards. The rate shall be inclusive of plastic sheet covering and protecting the
carpet till instructed to remove the same by the architect.
Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a
cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile
(Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed.
iii)Executive range-2 (Sizes 600 mm x600mm and above)
i) Nitco made
Supply and Laying of high pressure laminated Anti static false flooring of 300mm height including
making necessary step of 150mm height in entry level with skirting and garter as required to make
the room finish estatic with the other tiled portion.
CARPET FLOOR
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be
specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle
green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,
over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement
slurry @ 3.3Kg per Sqm, including pointing in white cement mixed with pigment of matching shade
complete
VITRIFIED TILE FLOORING
e). PVT- Hi Polish- PGVT
WALL TILES
CERAMIC GLAZED TILES
VITRIFIED
ANTISKID TILES
PAGE 12 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Sqm 1500.00
55
Sqm 448.00
56
Sqm 306.77
57
Sqm 18.30
Sqm 149.73
58
Sqm 55.00
59
GRANITE CLADDING
Stone tile work for wall lining upto 10 m height with special adhesive over 12mm thick bed of
cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement with an admixture
of pigment to match the stone shade.
Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by
Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse
sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with
Udaipur green marble
Raj Nagar plain
Granite stone of any colour and shade.
8mm thick (mirror polished and machine cut edge)
Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar
refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped
surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse
sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including
rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm
height along the parapet walls in the same manner.
MARBLE STONE FLOORING
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the
manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved
make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),
including grouting the joints with white cement and matching pigments etc., complete.
Size of Tile 600x600 mm
HEAT RESISTANT TERRACE TILE
GOUTING OF FLOORING TILE JOINT
Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 Kg
of organic coated filler of desired shade (0.10 Kg of hardener and 0.20 Kg of resin per Kg),
including filling / grouting and finishing complete as per direction of Engineer-in-charge
Size of Tile 600x600 mm
WALL TILES
PAGE 13 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Sqm 556.00
1
Sqm 45.00
60
Sqm 4987.27
61
Sqm 8173.05
62 Sqm 7098.50
63
Two Coats. Sqm 54.60
Sqm 150.00
64
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall
surface :
Water thinnable cement primer
Colour washing such as green, blue or buff to give an even shade :
New work (two or more coats) with a base coat of white washing with lime.
Providing polished MULTIWYN or Equivalent tiles as approved by EIC of approved quality, size,
shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick
in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush
pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with
approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement
plastering to be measured and paid separately). (Coloured pigment should be in conformity with
colour of tiles and as approved and directed by the Department). (Walls means both interior and
exterior walls). (Willow, Brick, Marvel, Sigma, Enamora, Pyramid, Crocotile, Bricket, Denver)
WATER PROOFING CEMENT PAINT
Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per
manufacturer's specifications including appropriate priming coat, preparation of surface, etc.
complete.
On concrete work
Proividing polished Multiwyn/DEVI/ VITA tiles of approved quality, size shape of specified
thickness on pavers over a base course including cutting where necessary finished with flush
pointing with Fix-A-Tile(Choksey/Sika/Pedelite/Rouf) white cement slurry mixed with approved
pigment to match shade of tiles complete at all levels as specified and directed. Pavers Tiles
(300x300) & thickness as per manufacturer specification of any shade & design as approved
PAINTING
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and
manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less
than 50 grams/ litre, of approved brand and manufacture, including applying additional coats
wherever required, to achieve even shade and colour.
PAVER TILES
PAGE 14 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Sqm 172.98
Sqm 242.20
65
Sqm 350.00
66
Sqm 6893.90
Sqm. 27.25
67
Sqm. 2.40
68
Sqm 250.00
New work (Two or more coats applied @ 3.84 Kg/10 Sqm
PAINTING ON STEEL AND OTHER METAL SURFACE
Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile
Organic Compound ) content.
With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250
grams/ litre
Finishing walls with water proofing cement paint of required shade
For vertical surface two coats @0.70 kg per sqm per coat sqm.
For horizontal surface one coat @1.10 kg per sqm. sqm.
Finishing with Deluxe Multi paint system for interiors and exteriors using primer as per
manufactureers specifications
Two Coats or more applied on walls @1.25ltr/10Sqm over and including one coat of special primer
applied @.75ltr/10Sqm
Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat
applied @ 0.90 ltr/10 Sqm over an under coat of primer applied @ 0.80 ltr/ 10 Sqm of approved
brand or manufacture
With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and
soft wood)
Applying priming coat :
Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing
treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs,
podiums, reservior, sewage & water treatment plant, tunnels/subway and bridge deck etc., prepared
by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces
and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the
same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the
requirements as specified in ACI- 212-3R-20 10 i.e by reducing permeability of concrete by more
than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic
pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a
width of 0.50mm. The work shall be carried out all complete as per specification and the direction of
the engineer-in-charge. The product performance shall carry guaranteed for 10 years against any
leakage.
PAGE 15 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
69
2079.00
70
Sqm 101.31
Sqm 82.50
Sqm 11.22Two track two panels sliding window made of (smallseries) frame 52 x 44 mm & sash 32 x 60 mm
bothhaving wall thickness of 1.9 ± 0.2 mm and singleglazing bead of appropriate dimension. (Area
ofwindow upto 1.75 sqm)
(a) Removing white or colour wash by steel wire brushing and/ or scraping, sand
papering and preparing the wall surface smooth including necessary repairs to scratches
complete.
Three track three panels sliding window made of (bigseries) frame 116 x 45 mm & sash 46 x 62 mm
bothhaving wall thickness of 2.3 ± 0.2 mm and singleglazing bead / double glazing bead of
appropriatedimension. (Area of window above 1.75 sqm)
UPVC WINDOWProviding and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height
dimension uPVC multi-chambered frame with in-built roller track and sashcomprising of extruded
profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll
forming process of required length (shape & size according to uPVC profile),appropriate dimension
of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy
(white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight
bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and
necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at
all corners, includingdrilling of holes for fixing hardware's and drainage of water etc. After fixing
frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon
sealent over backerrod of required size and of approved quality, all complete asper approved
drawing & direction of Engineer-in-Charge. (Single/ double glass panes, wire mesh and silicon
sealant shall be paid separately)
Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth &
width of profile shall be acceptable.
Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm
both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of
appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).
REMOVING COLOUR
PAGE 16 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Sqm 178.15
71
Sqm 10.00
Sqm 9.42
72
Mtr 60.00
73
Kg 190.00
74
For fixed portion
Providing and fixing glazing in Aluminium door, window, ventilator shutters and partitions etc. with
EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of
engineer-in-charge (Cost of Aluminium snap beading shall be paid in basic item): for windows &
ventilators
With float glass panes of 4.0 mm thickness
Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing
weather silicon sealant over backer rod of approved quality as per architectural drawings and
direction of Engineer-in-charge complete.
Upto 5mm depth and 5 mm width
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded
built up standard tubular sections/ appropriate Z sections and other sections of approved make
conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including
necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/
neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat angle, Aluminium snap beading for glazing /
paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the
directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868,
Minimum anodic coating of grade AC 15)
With float glass panes of 8.0 mm thickness
STRUCTURAL GLAZING
ALUMINIUM WINDOW
Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors,
windows and clerestory window shutters.(Area of opening for glass panes excluding portion inside
rebate shall
5.5 mm thick instead of 4 mm thick
PAGE 17 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Sqm 431.00
75
Sqm 794.80
76
each 18.00
Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-
12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and
specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and
shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat
strengthened clear float glass 6mm thick, spacer tube 12mm wide, desiccants, including primary seal
and secondary seal (structural silicone sealant) etc., all complete including scaffolding for the
required performances, as per the Architectural drawings, as per the approved shop drawings, as
specified and as directed by the Engineer-in-Charge.
The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of
IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual
area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone
sealant) provided and fixed in position, shall be measured in sqm.
(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm
Airgap + 6mm HeatStrengthened clear Glass of approved make having properties as visible Light
transmittance (VLT) of 25 to 35 %, Lightreflection internal 10 to 15%, light reflection external 10 to
ALUMINIUM COMPOSITE PANEL SHEET
Designing, fabricating, testing, installing and fixing in position Curtain Wall with
Aluminium Composite Panel Cladding, with open grooves for linear as well as
curvilinear portions of the building, for all heights and all levels etc. including:a)
Structural analysis & design and preparation of shop drawings for pressure equalisation
or rain screen principle as (b) Providing, fabricating and supplying and fixing panels of
aluminium composite panel cladding in pan shape in metalic colour of approved shades
made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR
grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The
aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based
PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on
face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel
screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.required,
proper drainage of water to make it watertight including checking of all the structural and
functional design(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot
Dip Galvanised with serrations and serrated as per specification and drawing The item DEMOLISHING & DISMANTLING
Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats,
architrave, holdfasts etc. complete and stacking within 50 metres lead
of area 3 sq. metres and below
PAGE 18 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
each 123.00
77
Sqm 27.00
Sqm 1235.00
78
Sqm 13.3078
Sqm 172.00
79
cum 68.85
80 cum 32.18
81 Sqm 33.68
82 each 15.00
83 cum 33.00
84 Sqm 627.60
85 Sqm 1348.40
existing inclined roof above switch room .control room & director's chamber & roof slab and beam
of main entrance
Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful
materials near the site and disposal of unserviceable materials within 50 metres lead
Removing mortar from and cleaning stones and concrete articles (net quantity of stacks of cleaned
materials will be measured) :
Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including
disposal of rubbish to the dumping ground within 50 metres lead.(Internal & External)
Demolishing cement concrete manually/ by mechanical means including disposal of
material within 50 metres lead as per direction of Engineer - in - charge.
Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
For thickness of tiles 10 mm to 25 mm
Dismantling roofing including ridges, hips, valleys and gutters etc, and stacking the
material within 50 metres lead of
G.S Sheet
Dismantling Aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling
including disposal of unserviceable surplus material and stacking of serviceable material with in 50
meters lead as directed by Engineer-in-charge.
Demolishing brick work manually/ by mechanical means including stacking of serviceable material
and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and
disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge
Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work
(Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of
Engineer -in -charge
existing inclined roof above switch room .control room & director's chamber & roof slab and beam
of main entrance
For thickness of tiles above 25 mm and up to 40 mm
0f area beyond 3 sq. metres (windows & ventilators)
Dismantling tile work in floors and roofs laid in cement mortar including stacking
material within 50 metres lead.
In cement mortar
PAGE 19 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
86
cum 5.00
87
Sqm 1350.00
Sqm 388.00
88
each 2.00
89
Job 1.00
90 Cum 261.30
91
Cum 261.30
92
Cum 261.30
93 Cum 87.10
94
MANHOLE COVER
Supplying and fixing C.I. cover without frame for manholes
500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 Kg
15 mm cement plaster on rough side of single or half brick wall
finished with a floating coat of neat cement of mix :
Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in
uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity
in stages to proper grade and camber, applying and brooming requisite type of screening / binding
material to fill up interstices of coarse aggregate, compacting to the required density .watering and
Laying water bound macadam sub-base with brick aggregate and blinding material, earth etc.
including screening, sorting and spreading to template and consolidation with light power road-roller
etc. complete.(payment for brick aggregate and moorum etc. to be made separately
Over burnt (Jhama) brick aggregate 90 mm to 45 mm
Grading material
Supplying and stacking at site.
Stone screening 13.2 mm nominal size (Type A)
Demolishing cement concrete manually/ by mechanical means including disposal of material within
50 metres lead as per direction of Engineer - in- charge.
Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)
Non Distructive Evaluation
Non destructive evaluation (NDE) of existing STPI building (near LGBI, Airport) at Borjhar,
Guwahati for structural stability by IIT Guwahati
Stone screening 11.2 mm nominal size (Type
PAVER'S BLOCK
1:3 (1 cement: 3 fine sand)
Road Work
12 mm cement plaster of mix :
1:4 (1 cement : 4 fine sand)
Plaster
PAGE 20 of 79
BOQ FOR CIVIL WORK Sl.
No.Description Unit Rate (Rs.) Amount (Rs.) Quantity
Sqm 522.60
95
Set 1.00
96
LS 1.00
Entry Gate
Construction of entary gate as per the design approved and specifications
PVC Septic Tank
Packaged One Piece Construction unit SEPTIC tank, 110 mm inlet and outlet provision with
flexible connector and 550mm Manhole
MAKE: Supreme/Sintex/SGIPL
Capacity: 21500
No. of Persons: 90 - 100 People
Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30
grade made by block making machine with strong vibratory compaction, of approved size, design &
shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse
sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.
Total
PAGE 21 of 79
1 WATER CLOSET
Providing and fixing water closet JAQUAR . Model no ARS-WHT- 39951 Each 7.002 BASIN FOR ALL OTHER LOCATION ( WASH ROOM)
Continentel Model no.CNS-WHT-601
Counter top basin Each 10.003 URINAL WITH SENSOR
JAQUAR model no URS -WHT-13255 Each 6.004 CONSEAL CISTERN WITH FLOOR MOUNTING FRAME
Model no. CIB-WHT-31801011XF Each 7.00FLUSH PLATE FOR CISTERN
Model no CIS-CHR-31207219 Each 7.00
5 WASTE PIPE
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings
complete.
Flexible pipe
40 mm dia Each 7.006 C.I. GRATING
Providing and fixing 100 mm sand cast Iron grating for gully trap Each 10.007 COUPLING
Providing and fixing in position waste coupling 32mm size full thread
with 130mm ht. ALD-705L130
Each
10.008 MIRROR
Providing and fixing mirror of superior glass (of approved quality) and of required shape and
size with plastic moulded frame of approved make and shade with 6 mm thick hard board
backing :
Circular shape 450 mm dia Each 3.00Rectangular shape 1500x450 mm Each 1.00
9 PAPER HOLDER
Providing and fixing Jaguar make toilet paper holder (AKP-35753P) Each 7.00
10 PVC PIPES,BENDS,JUNCTIONS,TEES ETC.
Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved
including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels
including below G.L as directed and specified.
Exposed
(i) 160mm dia. metre 18.00(ii) 110mm dia. metre 15.00
BOQ FOR SANITARY INSTALLATION & WATER SUPPLY
SL.
NO.
ITEM DESCRIPTION UNIT QTY RATE Amount (Rs.)
PAGE 22 of 79
BOQ FOR SANITARY INSTALLATION & WATER SUPPLY
SL.
NO.
ITEM DESCRIPTION UNIT QTY RATE Amount (Rs.)
iv 75 mm diameter metre 10.00b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the
damages.
(ii) 110mm dia. metre 20.00
iv 75 mm diameter metre 22.00Supplying fitting and fixing 45 degree PVC bends of supreme/prince or other ISI approved
including joining, fitting........
in exposed surface or in treanch
160mm dia pipe Each 10.0075 mm dia pipe Each 10.00
11 b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the
damages.
(ii) 110mm dia. Each 15.00(iv) 75 mm dia. Each 15.00
12 Supplying fitting and fixing PVC plain single tee of supreme/prince or other ISI approved
including joining, fitting........
in exposed surface or in treanch Each 10.00160mm dia pipe Each 15.0075 mm dia pipe
13 b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the
damages.
(ii) 110mm dia. Each 8.00
iv 75 mm dia pipe Each 8.00Supplying fitting and fixing PVC plain single"Y" of supreme/prince or other ISI approved
including joining, fitting........
in exposed surface or in treanch Each 6.00160mm dia pipe Each 6.0075 mm dia pipe
14 b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the
damages.
(ii) 110mm dia. Each 7.00
iv 75 mm dia pipe Each 9.0015 75 mm dia
Supplying fiting and fixing PVC cross ‘T’ plain of (Supreme/Prince) or other ISI approved
including joining , fitting and fixing etc. as necessary complete at all levels including below
G.L. as directed and specified.
16 a) In exposed surfaces or in trenches.
(i) 110mm x110mm Each 8.0017 (ii) 75 mm x 75mm Each 8.00
PAGE 23 of 79
BOQ FOR SANITARY INSTALLATION & WATER SUPPLY
SL.
NO.
ITEM DESCRIPTION UNIT QTY RATE Amount (Rs.)
b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the
damages.
18 (i) 110mm x110mm Each 7.00(ii) 75 mm x 75mm Each 7.00
19 Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI
approved including joining , fitting and fixing etc. as necessary complete at all levels
including below G.L. as directed and specified.
. a) In exposed surfaces or in trenches.
(ii) 75 mm x 75mm Each 4.0020 b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the
damages.
(i) 110mm x110mm Each 6.00(ii) 75 mm x 75mm Each 6.00
21 Supplying fiting and fixing PVC coupler of (Supreme / Prince)or other ISI approved
including joining , fitting and fixing etc. as necessary complete at all levels including below
G.L. as directed and specified.
a) In exposed surfaces or in trenches.
(i) 110 mm dia Each 3.00(iii) 75 mm dia Each 3.00b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the
damages.
(i) 110 mm dia Each 4.0022 (iii) 75 mm dia Each 4.00
Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including
joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as
directed and specified.
a) In exposed surfaces or in trenches.
23 (i) 160mm x 110 mm Each 4.00Supplying fiting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved
including joining , fitting and fixing etc. as necessary complete at all levels including below
G.L. as directed and specified.
a) In exposed surfaces or in trenches.
24 (i) 160mm x 110 mm Each 3.00Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved
including joining , fitting and fixing etc. in exposed surface or trences as necessary
complete at all levels including below G.L. as directed and specified.
(a) 110 mm Each 7.00(b) 75 mm Each 7.00
25 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and
colour.
PAGE 24 of 79
BOQ FOR SANITARY INSTALLATION & WATER SUPPLY
SL.
NO.
ITEM DESCRIPTION UNIT QTY RATE Amount (Rs.)
Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60
gms
Each
7.0026 BOTTLE TRAP
Providing and fixing Jaquar make 32mm dia Bottle Trap ALD-
CHR-7692
Each
7.00
27 SOAP DISPENSER WITH GLASS BOTTLE( AKP-35735P) Each 7.0028
towel rail squre round flange (AKP-35721P) Each 7.0029 COWEL
providing fitting and fixing PVC cowel of ISI make complete as directed and specified
75mm dia Each 3.0030 SHELF
Providing and fixing 600 mm glass shelf with edges round off (
AKP-35771P)
Each
7.00
COAT HOOK
( CAN-1161N ) double coat hook Each 4.00
TOWEL RACK
( AKP-36781P) 600 mm long with lower Hanger Each 4.00
SOAP DISH
(AKP- 35731P) soap dish holder Each 4.00
31 uPVC pipe with uPVC fittings ( Using uPVC high pressure pipe)
(Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe)
160mm diameter RM 29.20
INTERNAL WATER SUPPLY
C.P.V.C. PIPES
32 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability
for hot & cold water supply, including all CPVC plain & brass threaded fittings, including
fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with
one step CPVC solvent cement and testing of joints complete as per direction of Engineer in
Charge.
Internal work -
20mm nominal outer dia Pipes metre 20.00 25 mm nominal outer dia Pipes metre 25.00
PAGE 25 of 79
BOQ FOR SANITARY INSTALLATION & WATER SUPPLY
SL.
NO.
ITEM DESCRIPTION UNIT QTY RATE Amount (Rs.)
32 mm nominal outer dia Pipes metre 20.00 40 mm nominal outer dia Pipes metre 45.0050 mm nominal outer dia Pipes metre metre 25.00
33 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability
for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the
pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step
CPVC solvent cement and the cost of cutting chases and making good the same including
testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc.
15 mm nominal outer dia Pipes metre metre 60.00 20mm nominal outer dia Pipes metre 20.00
35 Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and
making long screws etc. complete (cost of water meter and stop cock to be paid separately).
Each
7.00
BIB COCK
Providing and fixing bib cock of approved quality :ORP-10041PM, 2-way with wall flange Each
7.00
Providing and fixing Angular stop cock of approved quality :( ORP-1053PM) Each 7.00 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
25 mm nominal bore Each 4.00 32 mm nominal bore. Each 4.00
36 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic
floats complete :
20 mm nominal bore Each Each 4.00 25 mm nominal bore Each Each 4.00
37 Providing and fixing gun metal non- return valve of approved quality (screwed end)
25 mm nominal bore
Horizontal Each 4.00 Vertical Each 4.00 32 mm nominal bore
Horizontal Each 4.00 Vertical Each 4.00
38 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the
main :
20 mm nominal bore Each 4.00 25 mm nominal bore Each 4.00
39 Providing and fixing uplasticised PVC connection pipe with brass unions :
PAGE 26 of 79
BOQ FOR SANITARY INSTALLATION & WATER SUPPLY
SL.
NO.
ITEM DESCRIPTION UNIT QTY RATE Amount (Rs.)
30 cm length
20 mm nominal bore Each 8.00 20mm nominal bore Each 8.00
40 HEALTH FAUCET
Hand shower( Health faucet) with 8mm dia , 1.2m long flexible tube
and wall hook NRV ( back flow preventer ) Each 7.00
SHOWER
(OHS-CHR-1637 ) Maze overhead shower size 190x295 mm
rectangular shape single flow ( body &face plate stainless steel with
chrome finish with rubit cleaning system Each 2.00
WALL MIXER
(ORO-10117PM) Single lever wall mixer with provision for overhead
shower with 115mm long bend pipe on uper side Each 2.00
41 WATER TANK
Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon
/ Patton make over the stagging with manhole cover with locking and cleaning arrangement
including providing pads of size as required for inlet and outlet pipes
2000 Litre capacity PCVC Tank Each 3.0042 Providing, Supplying and Installation of fresh Coloured 12mm thick High Pressure
Laminated (HPL) Modular Toilet Cubicle Partition of Make Merino Model Type ZMS
NYLON SERIES or Equivalent Make with Size of Cubicle : 1.2m ( Average Width) & 1.5
m(Average Depth) x 2003mm (H) Door Size : 1750mm (H) x 610mm (W) , The Overall
Height Of Cubicle should be atleast 2005mm (Including bottom Gap of 150mm)
Accessories :a) Aluminium “U” Channel b) Aluminium “F” channel c) Aluminium Door
Stopper Channel d) Aluminium Top Rail e) Nylon Coat Hook f) Nylon Privacy Thumb turn
c/w Occupancy Indicator g) Nylon Door Knob h) Nylon Hinges – Gravity to close i) Nylon
Adjustable Foot j) Rubber Door Stopper Lining k) S.S.Screws 304 G & P.V.C Wall Plugs as
Directed by Architect.for 7 nos of WC with the drawing attached for 3rd floor.
JOB 1.00
DEEP Tubewell
43 Labour for sinking tube well with 40mm (internal) dia G.I. Pipes up to having strata, having
potable water including fitting and fixing strainer hand pump and other accessories as directed
complete as in any soil. Rm 200.0044 Labour for test boring with 40mm (internal) dia G.I. Pipes including keeping surplus of earth
and every 2.00m after first 3.00m depth and delivering the same in nearest P.W.D. camp in the
small tin container (container, scaffolding, tools etc. will have to be arranged by the
contractor at his own cost). Rm 200.00
PAGE 27 of 79
BOQ FOR SANITARY INSTALLATION & WATER SUPPLY
SL.
NO.
ITEM DESCRIPTION UNIT QTY RATE Amount (Rs.)
45 Supplying fitting and fixing Hand pump for 40 mm dia tube well with all accessories
complete as directed.
ii) Mayur Each 1.00Supplying, fitting and fixing lift and force Maya hand pump of approved with all accessories
complete as directed by the Department.. Each 1.0046 Labour for boring hole for inserting tube well pipes through different soil/ rock media
including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out
the same and lowering pipes, fittings complete as directed by the Department.
vi) Bore hole of 200mm diameter Rm 250.0047 Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS
codes of practice including supplying and fitting of tube well accessories, lowering of
assembly pipes concentrically in the borehole followed by supplying and packing of pea
gravel free from dirt, dust and other foreign materials in the annular space between the
borehole and assembly pipes complete as directed by the Department.
PVC PIPE
SUPREME /PRINCE / FUSION /SFMC Brand
viii) 200mm diameter Rm 3.0048 Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes
of practice including supplying and fitting of accessories, lowering of assembly pipes
concentrically in the casing pipes complete as directed.
B) PVC PIPE
SUPREME / PRINCE / FUSION /SFMC Brand
ix) 200mm diameter Rm 250.0049 Supplying fitting and fixing GI filter 2.00 metre long. Each 1.0050 Supplying fitting and fixing check valve(non return valve)including thread to pipes
c)40mm diameter Each 1.0051 Development of the tube well with compressor or by over pumping unit for 48 hours till sand
free discharge is obtained. Job 1.0052 Flushing clearing washing and watering of the tube well job 1.00
AS PER MARKET PRICES ANALYSIS
Supplying, Testing and Commissioning of 2 or 3BHP Submerssible pump of approaved
brand and make as per specification including all accessories like panel board, starter etc.
complete in all respect as directed by the architect. nos 1.00
TOTAL
PAGE 28 of 79
RAW & UPS POWER SUPPLY
1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated
copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type
switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm FRLS
PVC insulated copper conductor single core cable etc. as required.
Group C point 646.00
2 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC
insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as
required.
4 X 6 sq. mm + 2 X 4 sq. mm earth wire METRE 534.00
4 X 10 sq. mm + 2 X 6 sq. mm earth wire METRE 262.00
4 X 16 sq. mm + 2 X 10 sq. mm earth wire METRE 90.00
3 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC
insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as
required.
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire METRE 2286.00
2 X 4 sq. mm + 1 X 4 sq. mm earth wire METRE 1554.00
2 X 6 sq. mm + 1 X 6 sq. mm earth wire METRE 1326.00
2 X 10 sq. mm + 1 X 6 sq. mm earth wire METRE 1110.00
2 X 16 sq. mm + 1 X 6 sq. mm earth wire METRE 444.00
4 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable
in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper
conductor single core cable for loop earthing as required.
METRE 2282.00
5 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable
in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper
conductor single core cable for loop earthing as required.
METRE 60.00
6 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core
cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable
GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable
etc. as required.
EACH 6.00
7 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for
modular switches in recess etc. as required.
1 or 2 Module (75 mmX75 mm) EACH 10.00
3 Module (100 mmX75 mm) EACH 369.00
4 Module (125 mmX75 mm) EACH 9.00
BOQ FOR INTERNAL ELECTRICAL WORK SL. NO. ITEM DESCRIPTION UNIT QTY RATE AMOUNT
Page 29 of 79
BOQ FOR INTERNAL ELECTRICAL WORK SL. NO. ITEM DESCRIPTION UNIT QTY RATE AMOUNT
6 Module (200 mmX75 mm) EACH 35.00
8 Module (125 mmX125 mm) EACH 722.00
12 Module (200 mmX150 mm) EACH 32.00
8 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as
required.
1 or 2 Module Each 10.00
3 Module Each 369.00
4 Module Each 9.00
6 Module Each 35.00
8 Module Each 722.00
12 Module Each 32.00
9 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box
including connections but excluding modular plate etc. as required.
5/6 A switch EACH 940.00
2 way 5/6 A switch EACH 6.00
15/16 A switch EACH 132.00
3 pin 5/6 A socket outlet EACH 802.00
6 pin 15/16 A socket outlet EACH 118.00
10 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in
surface/recess including cutting the wall and making good the same in case of recessed conduit as
required. For Cable TV Wiring, LAN Cable et. As reqd. And specified in BOQ.
25 mm METRE 2262.00
11 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated,
shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed
steel/ PVC conduit as required.
METRE 504.00
12 Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including
connections etc. as required
TV antenna socket outlet EACH 10.00
13 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC
conduit as required.
1 run of cable METRE 8752.00
14 Supplying and installing following size of perforated painted with powder coating M.S. cable trays with
perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the
ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.
Page 30 of 79
BOQ FOR INTERNAL ELECTRICAL WORK SL. NO. ITEM DESCRIPTION UNIT QTY RATE AMOUNT
300 mm width X 50 mm depth X 1.6 mm thickness METRE 324.00
225 mm width X 50 mm depth X 1.6 mm thickness METRE 108.00
15 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB
distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper
bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer)
as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)
4 way (4 + 12), Double door EACH 6.00
8 way (4 + 24), Double door EACH 17.00
12 way (4 + 36), Double door EACH 8.00
16 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker
suitable for inductive load of following poles in the existing MCB DB complete with connections,
testing and commissioning etc. as required.
Single Pole Each 400.00
17 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete
with connections, testing and commissioning etc. as required.
40 A EACH 34.00
63 A EACH 37.00
18 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with
connections, testing and commissioning etc. as required.
40 A EACH 31.00
63 A EACH 30.00
100 A EACH 22.00
19 Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic
release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel,
making connections, etc. as required. For RAW Floor Panel DB Incoming.
150 A, 16 kA,TPMCCB EACH 1.00
250 A, 35 kA,TPMCCB EACH 2.00
20 Supplying with fitting and fixing of 25A Modular Motor Starter 2M , MODEL RANGE LEGRAND
(ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO)
including making necessary connection as per direction of department.
Each 71.00
21 Supplying with fitting and fixing of CAT 6 RJ-45 Computer jack in one module including making
necessary connection complete as per direction of department.
Each 546.00
Page 31 of 79
BOQ FOR INTERNAL ELECTRICAL WORK SL. NO. ITEM DESCRIPTION UNIT QTY RATE AMOUNT
22 Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double
door IP-43 double door surface mounting vertical TPN MCB DB incorporated with bas-bar 125A,
Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with
making necessary connection as approved, specified and directed by the deptt. UPS FLOOR
PANEL
Schneider neo break, C&S, Havells, INDOASIAN, HPL or equivalent as approved by the Deptt.)make)
8 way TPN (8+24) double door Each 3.00
23 Supplying with fitting and fixing MCCB income and MCB outgoing sheet steel, phosphatised, powder
painted single door surface mounting vertical TPN MCB DB incorporated with bas-bar, Neutral link,
Earth bar up to 125A and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with
making necessary connection as approved, specified and directed by the deptt. RAW POWER
FLOOR PANEL
(C&S, Havells, Indo Asian, HPL, V-Guard or equivalent make as approved by the Deptt.)
8 way TPN (4+24) single door Each
12 way TPN (4+36) single door Each 2.00
24 Supply, fitting and fixing of ceiling suspended slim panel high lumen output LED lighting fixtures of
CGL make ( Cat. Ref. LCPL-36-CDL(@x)), 36W fittings or equivelent make of Syska/Havell's/ Jaquar
as per prior approval of Deptt .
Each 220.00
25 Supply, fitting and fixing of ceiling suspended downlighter fixtures of CGL make ( Cat. Ref.LSCRM-
6W-CDL/NW/WW) of 12W Panel Light (Round) 12W 6" fittings or equivelent make of Syska/Havell's/
Jaquar as per prior approval of Deptt.
Each 372.00
26 Supply, fitting and fixing of LED Indoor Strip Light fixtures with necessary driver of Syska make ( Cat.
Ref.LSTP01X15XW) 25W fittings or equivelent make of CGL/Havell's/ Jaquar as per prior approval
of Deptt .
Each 3.00
27 Supplying, drawing, connecting, testing & commissioning of 2 core x 1.5 sq. mm. multi
stranded copper conductor, pvc insulated PVC sheathed, aluminium
myler tape shielded, Armoured cable suitable for Fire Alarm
System.(Make: Havels, Polvacb, Crvstal, Gloster, Finolex)
Mtr. 4200.00
28 SITC of Machine room less 08 passenger Auto Door,1.0 mps speed, Machine room less, 4
stops)Stainless Steel –Vandal proof Car & Doors with Auto Rescue Device: Shaft size: 1685
mm Wide X 1450 mm Deep
No. 1
Page 32 of 79
BOQ FOR INTERNAL ELECTRICAL WORK SL. NO. ITEM DESCRIPTION UNIT QTY RATE AMOUNT
No. of Elevators: 1 No. of Monospace Elevator for your project at Guwahati, Assam.
Type & Capacity : Passenger – Gearless- 08 Persons – 544 Kg
Speed : 1.0 Mtr/Sec (approx.)
Type of Drive : Variable Voltage Variable Frequency Drive with Microprocessor based
Simplex Full Collective Control.
Machinery : Permanent Magnet AC Synchronous Motor Eco Disc Drive(Machine
Room Less Type)
Available Travel : 9.9 mtrs. (Maximum)
Serving : Ground to 3rd Floor( 0,1,2,3)
Stops & Openings: 04 Stops 04 Levels 04 Openings
Car Size approx. : 1300 mm Wide x 1100 mm Deep
Required Pit Dpth: 1600 mm (Mandatory)
Rqrd Head Room : 4300 mm.
Car Enclosure : Stainless Steel –Vandal Proof Car
Flooring : PVC
Electric Light : LED Lighting
Fan : Axial Flow
Car Entrance : Centre Opening Stainless Steel Vandal proof Power Door (COPD)
with Vision panel
Clear Opening : 700 mm Wide x 2000 mm High
Indicators: Car : Direction & Position Indicator (SMLCD, Blue & White Back ground)
& Landings
Other Features : Emergency Alarm & Light., Call Registration LEDs., OSG Electronic Switch.
Fireman Drive, Two Station Intercom, Full Length Infra Red door Safety,
Rescue Device & Load weighing device, Lift Announcement System, Braille
Buttons
TOTAL
Page 33 of 79
1
Supplying and making end termination with brass compression gland and aluminium lugs for
following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV
grade as required
2 X 6 sq. mm (19mm) Each 38.00
2 X 16 sq. mm (22mm) Each 8.00
2 X 35 sq. mm (25 mm) Each 12.00
2 X 50 sq. mm (28mm) Each 6.00
3 X 50 sq. mm (32mm) Each 22.00
2
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing
masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long
etc. with charcoal/ coke and salt as required SET
14.00
3Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning
conductor complete as required.(For horizontal run METRE
875.00
4Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as
required METRE
246.00
5
Supplying and erection of 11 kV pin insulator complete with large steel head G.I. pin, nuts, washers
etc. as required SET
3.00
6
Supplying and erection of 11 kV disc insulator for 11 kV over head lines with galvanised insulator
fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as
required. SET
3.00
7
Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11
kV overhead lines with rated voltage 9 kV (rms) with a nominal discharge current rating of 5 kA and
complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required. SET
1.00
8
Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2
mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on
front side as required. EACH
4.00
9
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker
suitable for inductive load of following poles in the existing MCB DB complete with connections,
testing and commissioning etc. as required For Area Lighting Panel.
Double pole Each 10.00
10
Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete
with connections, testing and commissioning etc. as required.
63 A Each 4.00
BOQ FOR EXTERNAL AND COMMON ELECTRICAL WORKS QTYUNITITEM DESCRIPTIONSl. No. RATE AMOUNT
PAGE 34 of 79
BOQ FOR EXTERNAL AND COMMON ELECTRICAL WORKS QTYUNITITEM DESCRIPTIONSl. No. RATE AMOUNT
11 Supplying including installation, testing and commissioning of Readymade Panel board conforms to
IS : 8623, IEC : 60439 made of Phosphatised powder painted wall mounting type complete with Ana
log meter module cable Alley both LHS and RHS, Copper Bus bar, Din Rail, Neutral Bar, Earth Bar
etc. with Provision for 1 No. 4 pole MCCB as incomer and provision for 8 Nos. FP MCCB out
goings as specified and directed by the deptt. and comprising of the following electrical items:
1. Panel Board up to 250 A Incomer, O/G FP MCCBs
2. Meter Module- Digital (Provision for Ammeter, Voltmeter, Selector Switch, Control Fuses,
Indicating lights, MCBs etc.
3. cable Alley 8 Way for incoming 160Amp
(Incoming and Outgoing MCCB of reqd. rating will be measured and paid separately) Each 1.00
12 Supplying with fitting and fixing panel mounting open execution 25 KA 415V 50Hz 4P MCCB
(Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with
making necessary connection as approved by the Deptt.),as specified and directed by the deptt. for
above ACDB
25 KA 415V 50 Hz 4P MCCB
(Havells, Scneider, ABB make)
63A Each 5.00
100A Each 3.00
160A Each 1.00
13 Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV Grade Solid
Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up,
PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium
strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel
strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured
U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground
including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand
cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed
by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) .
4.00 Sq. mm.4 Core armoured U.G. cable Metre 300.00
6.00 Sq. mm.4 Core armoured U.G. cable Metre 232.00
10.00 Sq. mm.4 Core armoured U.G. cable Metre 80.00
16.00 Sq. mm.4 Core armoured U.G. cable Metre 65.00
25.00 Sq. mm.3 & 1/2 Core armoured U.G. cable Metre 166.00
35.00 Sq. mm.3 & 1/2 Core armoured U.G. cable Metre 252.00
70.00 Sq. mm.3 & 1/2 Core armoured U.G. cable Metre 95.00
PAGE 35 of 79
BOQ FOR EXTERNAL AND COMMON ELECTRICAL WORKS QTYUNITITEM DESCRIPTIONSl. No. RATE AMOUNT
150.00 Sq. mm.3 & 1/2 Core armoured U.G. cable Metre 124.00
300.00 Sq. mm.3 & 1/2 Core armoured U.G. cable Metre 390.00
14 Supply, fitting & fixing of Lighting Finial Arrestor made of 25 mm dia 300 mm long solid Copper
tube having 85 mm dia. single prong at top and 3 mm thick base plate at bottom complete with fitting
& fixing with Brass nuts & bolts on roof, RCC slab, top of column etc. as specified and directed by
the deptt. Each
4.00
15 MAIN LT PANELS : Supplying including installation, commissioning of vermin and dust proof
totally enclosed cubical indoor type floor mounting compartmentalize panel board made of 14 SWG
2 mm thick C.R.C.A sheet and powder coated using 11 Tanks pre-treatment process. Panel should
be fabricated using CNC maching. The panel board is to be erected in 100x 50mm MS Channel base
frame including all necessary earthing etc. complete neatly Wiring done. Bus Bar shall be of 1000A
aluminium E91 Grade. Panel shall be confirming to IP 43 protection comprising of the following
electrical items:
Incomer
800A 4P, 50kA MCCB -1 nos
400A 4P, 36kA MCCB- 2 nos
Digital Multifunction meter -3 nos
Indication lamp RYB -3 set
Protection MCB as per requirement.
CT 800/5 -1 set
CT 400/5 – 2 set
Bus Coupler – 400A 4P, 36kA MCCB
Incomer shall be Electrically and Mechanically interlocked
Outgoing:
1. 250A 4P, 36kA MCCB -4 nos
2. 160A 4P, 36kA MCCB- 2 nos
3. 160A 3P, 36kA MCCB- 1 nos
4. 100A 4P, 25kA MCCB -1 nos
5. 63A 4P, 25kA MCCB- 3 nos
All the MCCB shall be with extended rotary handle and both side spreader link.
1.00
16 Supplying, erection and commissioning of the following specification as per IS:2713 : 410 SP hot dip
Galvanized Steel tubular pole manufacturing out from electrically welded in 3 (three section having
a base plate including providing all required building materials as directed and specified by the deptt.
(BANSAL/SRP / Valmont / PARUTHI ENGR make)
PAGE 36 of 79
BOQ FOR EXTERNAL AND COMMON ELECTRICAL WORKS QTYUNITITEM DESCRIPTIONSl. No. RATE AMOUNT
410 SP 56 Length of pole = 11.00 metre., Length of sections, Bottom = 5.60 M, Middle = 2.70 M,
Top = 2.70 M, Out side dia. & Thickness Bottom = 193.70 x 5.40 mm, Middle =165.10 x 4.50 mm,
Top =138.70 x 4.50 mm Each
2.00
17 Supplying and fitting fixing of galvanised channel of 100 mm x 50 mm x 6 x 2200 mm long
complete with clamps ,blots, nuts etc. as required and as directed by the department. Each
6.00
18 Supplying and fitting fixing of galvanised Angle of 50 mm x 50 mm x 6 x 5000 mm long complete
with clamps ,blots, nuts etc. as required and as directed by the department. Each
4.00
19 Supplying and fixing of 11 KV 400 A Gang operated switch with all accessories complete as required
and as directed by the department. Set
1.00
20 Supplying and fixing of 11 KV 150 A D.O. fuse set complete as required and as directed by the
department. Set
1.00
21 Supplying and fitting fixing of P.G. clamp for Racoon conductor complete as required and as directed
by the department. Each
3.00
22 Supplying and string up AAAC Racoon conductor in the existing P.S.C./ M.S/ Galvanized pole with
binding etc. as required and as directed by the department. Directed by the department.
Metre.
30.00
23 Supplying, installation testing and commissioning of the following rating copper wound indoor / out
door type transformer complete including the payment to be made to power supply authority for
supervision charge, labour charge, cost of L.T/H.T metering etc. (excluding the cost of load security)
and making necessary arrangement for charging approval of the sub-station from the competent
authority as directed and specified by the department. Transformer should be as per CEA guidelines
as ammended up to date upto 200 KVA star rating up to 5 star, above 200KVA as per CEA
guidelines for losses along with LV enclosure.
500 KVA 33/0.433 KV. Oil filled transformer with Off Circuit tap change. Each 1.00
24 Supplying including installation, commissioning of vermin and dust proof totally enclosed cubical
indoor type floor mounting compartmentalize panel board made of 14 SWG 2 mm thick C.R.C.A
sheet and powder coated using 11 Tanks pre-treatment process. Panel should be fabricated using
CNC maching. The panel board is to be erected in 100x 50mm MS Channel base frame including all
necessary earthing etc. complete neatly Wiring done. Bus Bar shall be of 1000A aluminium E91
Grade. Panel shall be confirming to IP 43 protection. The panel board is to be erected in 1 : 3 : 6 PCC
foundation including brick soling / grouting etc. complete neatly Wiring done with provision for one
no 800A 4pole MCCB or Switch Fuse Unit as incomer and provision for 6nos DP or TPN out going
as specified and directed by the deptt. confirming to IP 43 protection comprising of the following
electrical items:
1. 40mm X 10mm 4 strip copper Bus - Bar 2.80 M length each
PAGE 37 of 79
BOQ FOR EXTERNAL AND COMMON ELECTRICAL WORKS QTYUNITITEM DESCRIPTIONSl. No. RATE AMOUNT
i 20mm X 3mm 4 strip copper Bus-Bar 0.6M each 4 sets
2. Digital 3 Phase Voltmeter Accuracy class 0.5 - 1 no
3. Digital 3 Phase Ammeter Accuracy class 0.5 - 1 no
4. Pilot Lamp with integral ckt LED 110- 230 V (Red, Yellow,& Blue - 3 no
5. Voltmeter & Ammeter Selector Switch - 2 no
6. 2 A Slide fuse unit - 3nos
7. Provision for ASEB's Metering
(Incoming & Outgoing Switch Gear of reqd. rating will be measured and paid separately) Each 1.00
25 Supplying with fitting and fixing panel mounting open execution 50KA 415V 50Hz 4P MCCB
(Ics=Icu, adjustable Ir setting 0.5-1, neutral adjustable with earth fault protection and with rotary
handle Without enclosure of the following capacity complete with making necessary connection as
approved, specified and directed by the deptt.
800A, 50 KA 415V 50 Hz 4P MCCB
(C&S, Schneider, ABB, L&T or equivalent make as approved by the Deptt.) Each
1.00
26 AREA LIGHTING PANEL : Supplying including installation, commissioning of vermin and dust
proof totally enclosed cubical indoor type floor mounting compartmentalize panel board made of 14
SWG 2 mm thick C.R.C.A sheet and powder coated using 11 Tanks pre-treatment process. Panel
should be fabricated using CNC maching. The panel board is to be erected in 100x 50mm MS
Channel base frame including all necessary earthing etc. complete neatly Wiring done. Bus Bar shall
be of 1000A aluminium E91 Grade. Panel shall be confirming to IP 43 protection. The panel board is
to be erected in 1 : 3 : 6 PCC foundation including brick soling / grouting etc. complete neatly Wiring
done with provision for one no 100/125Amp 4pole MCCB or Switch Fuse Unit as incomer and
provision for 10 nos DP or TPN out going as specified and directed by the deptt. confirming to IP 65
protection comprising of the following electrical items:
1. 20mm X 3mm 4 strip copper Bus-Bar 0.5M length each
2. Digital 3 Phase Voltmeter Accuracy class 0.5 - 1 no
3. Digital 3 Phase Ammeter Accuracy class 0.5 - 1 no
4. Pilot Lamp with integral ckt LED 110- 230 V (R, Y,& B - 3 no
5. Voltmeter & Ammeter Selector Switch - 2 no
6. 2 A Slide fuse unit - 3nos
(Incoming & Outgoing Switch Gear of reqd. rating will be measured and paid separately) Each 1.00
27 Supplying including installation testing and commissioning of 150kVAr, 440V APFC Panel Non-
Compartmentalized Type, Free Standing, Floor Mounted
rated Output 150kVAr
rated Voltage 440V
PAGE 38 of 79
BOQ FOR EXTERNAL AND COMMON ELECTRICAL WORKS QTYUNITITEM DESCRIPTIONSl. No. RATE AMOUNT
rated Frequency 50Hz
Number of phases 3 Phase
Switching Option Auto-Manual
ENCLOSURE DETAILS
Material CRCA
Thickness of sheet steel Frame & Doors: 2.0mm, Partitions: 1.6mm, Gland plate: 3.0mm
Dimensions W x H x D (mm) 800 x 1800 x 600 (Approx) + (250 mm for plinth & fan hook
Ingress Protection IP 42
Installation Type Indoor
Cable Entry Bottom
Colour RAL 7035 - Light Grey
BUSBAR DETAILS
Material Aluminium
Cross Section (mm) 40 x 10 x 1 Run
Bus bar Supports DMC Moulded
CAPACITORS
Heavy Duty @ 440V
No of Steps 5
SWITCHGEAR DETAILS
Incomer MCCB, 320A, 36kA CVS Type
Switching Capacitor Duty Contactors
Step Protection MCB/MCCB
APFC RELAY
INCOMER MCCB, 320A, 36kA CVS Type
Digital Volt - Amp Freq meter 1
Phase Indicating Lamps (L1, L2, L3) 3
Current Transformer - 300/5A
APFC Relay 1
Fans 1
Control Circuit Protection - MCB 2
Step Indicating Lamps 10
On / Off push buttons 10
Step protection - MCCB, CVS Type, 25kA - 100A 1 SET 1.00
PAGE 39 of 79
BOQ FOR EXTERNAL AND COMMON ELECTRICAL WORKS QTYUNITITEM DESCRIPTIONSl. No. RATE AMOUNT
28 Supplying including installation, testing and commissioning of Water Cooled Diesel Generator set
coupled to suitable alternator of 415 V, AC, 3-Phase 0.8 p.f.(la mounted on a 1) M.S. Fabricated
base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) EMF/Standard Control
Panel.5) Suitable batteries with lead.,5) First fill of lube oil.,6) Acoustic Enclosure complete with all
accessories as specified and directed by the department conforming to IS comprising the following
Technical Specification.. (RANGE FROM 200 KVA TO 1010 KV
TECHNICAL DATA
GENERATOR SET SPECIFICATIONS e
1. Model. C - 18- DITA GP - 1
2. Prime Power Rating KVA/KW. 250/200
3. No. of Phases. 3 phase.
CATERPILLAR ENGINE SPECIFICATION.
1. make).
3. No. of Cylinders. 6
4. Aspiration. Natural
5. Cooling. Water Cooled/ AIR COOLED
6. Governor. Mechanical/Electronic
7. Battery Capacity Rating. 120 AH 2X12 Volt.
ALTERNATOR SPECIFICATION.
1. make).
2. Voltage Regulation. +/- 1.0%
3. Insulation. Class - H.
4. Standard Enclosure. IP 23
5. No. of Phases. 3
KVA 250
WITH AMF CONTROL PANEL Each 2.00
29 Supplying and fitting fixing of electric storage water heater [Geyser] of AOS-Jaquar make) including
necessary connection etc. as required complete and as directed by the Department.
15 Litre Capacity (Digital model) Each 1.00
30 Supplying including fitting fixing of following star rated A.C. Ceiling fan complete with all
accessories like down rod, canopy etc. of following sweeps with making necessary connection cable,
as approved by the Deptt.s etc. as required complete and as directed by the Department [Without
regulator]. (ORIENT PSPO make / Usha make/ CROMPTON make/ Havells/ ATC/ V GAURD
make)
Energy efficient 5-star 1200 mm sweep Fusion 5 star (Havells or equivalent make) Each 4.00
PAGE 40 of 79
BOQ FOR EXTERNAL AND COMMON ELECTRICAL WORKS QTYUNITITEM DESCRIPTIONSl. No. RATE AMOUNT
31 Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of
following sweeps with making necessary connection as approved by the Deptt.)as required complete
and as directed by the Department.
High Speed 225 mm sweep (ORIENT make), Trans Air 225 mm sweep (Crompton make), Ventil
Air DX 250 mm sweep Louver type (Havells make) Each
16.00
32 Supplying fitting and fixing of single wall brackets Philips model 37554 (or equivalent as approved
by the Deptt.) on the wall in GI/ MS switch board (ISI marked) half conceal on wall with phenolic
laminated sheet cover with all accessories including connection as required complete. Without
lamp. Each
18.00
33 Supplying including installation, connection as approved by the Deptt., testing and commissioning of
SUBMERSIBLE PUMP SET, Single Phase with steel cable rope and submersible cable complete as
directed and specified by the deptt.
Three phase Submersible motor pump set (Texmo / Crompton Greaves/ Aquatic/ CRI/ V-Guar
suitable for 100 mm bore well and above. 5 HP STAGE 14 to 50 with MCB controlled Submersible
motor pump set control panel. Each
1.00
2 HP single Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard
make) 2900 rpm with DOL Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T /
Siemens make) . Each
1.00
34 Supply, fitting and fixing of LED Gate Light fixtures with necessary CG boxes if required of CGL
make ( Cat. Ref.LPTOI-45-CDL/T)) fittings or equivelent make of Havell's/ Jaquar /Philips as per
prior approval of Deptt . Each
2.00
35 Supply, fitting and fixing of LED Facade Lighting fixtures with necessary CG boxes if required of
CGL make ( Cat. Ref.LSFO-60-CDL) fittings or equivelent make of Havell's/ Jaquar /Philips as per
prior approval of Deptt . Each
4.00
36 Supply, fitting and fixing of LED decorative post top Light fixtures with necessary CG boxes if
required of CGL make ( Cat. Ref.LPTO-40-WW/M) fittings or equivelent make of Havell's/ Jaquar
/Philips/Syska as per prior approval of Deptt . Each
12.00
37 Supply with fitting & fixing 50 mm dia 2440 mm height painted finish tubular GI pole .The pole is
made of GI tube radiating from specially designed cylindrical pedestal block with built in pre-cabled
controls and service door . The pole is welded with circular GI base plate .The pole is designed for 1
No. LED Post Top Lentarn and suitable for operation on 240 V 50 Hz single phase AC supply . The
pole is to be fitted on 1:3:6 PCC pole foundation of size 300 mmx300 mmx 600 mm with grouting
nuts & bolts as specified & directed by the deptt .(Metal Coats make). of reputed model or
equivalent. Each
12.00
PAGE 41 of 79
BOQ FOR EXTERNAL AND COMMON ELECTRICAL WORKS QTYUNITITEM DESCRIPTIONSl. No. RATE AMOUNT
38 82 KVA On-Line UPS System (DELTA/ Orion or equivalent make as approved by the Deptt.) with
PWM-IGBT technology 360V AC Input (300V – 470V A 3 Ph input- 3 Ph output With Isolation
Transformer 70KW output with 0.85 output PF 120 min backup using SMF battery
Each
1.00
TOTAL
PAGE 42 of 79
A Supply of 3Star Hi wall AC Units of make
Bluestar, Daikin, Hitachi or equivalent.
1 1 TR 3 Star Hi wall Nos 1.00
2 1.5 TR 3 Star Hi wall Nos 4.00
B Supply of Non- Inverter cassette AC Units of
make Bluestar, Daikin, Hitachi or equivalent.
1 1.5 Tr Nos 7.00
2 1.8 Tr Nos 12.00
3 2.4 Tr Nos 5.00
4 2.9 Tr Nos 7.00
5 3.5 Tr Nos 4.00
6 3.8 Tr Nos 6.00
C Supply of Air Cooled DUctable Split Units of
make Bluestar, Daikin, Hitachi or equivalent.
complete with DX coil, filters, blowers with
motor and drive. The outdoor unit shall have
condenser coil, fans with motor and drive,
scroll compressor, panel etc. Supply of Air-
cooled Ductable Units with micro-processor
based controls with (R-22) machine.
1 11 TR Ductable AC Nos 2.00
BOQ FOR HVAC LOW SIDE
1Installation testing commissioning of High wall
Split ac UnitsNos
5.00
2Installation testing commissioning of Cassette ac
UnitsNos
41.00
BOQ FOR HVAC HIGH SIDE & LOW SIDE
Sl. No. Description Unit Qty Rate Amount
PAGE 43 of 79
BOQ FOR HVAC HIGH SIDE & LOW SIDE
Sl. No. Description Unit Qty Rate Amount
3Installation testing commissioning of 11 Tr
Ductable AC unitsNos
2.00
4Supply and installtion of Copper pipe with
insulation for split ACRmt
25.00
5Supply and installtion of Copper pipe with
insulation for Ductable and Cassette AcsRmt
336.00
6 Supply installation of Electrical cable Rmt 361.00
7 Supply installation of Drain Pipe Rmt 70.00
8Supply installation of 40 mm PVC with nitrle
rubber Insulation for AHu unitsRmt
250.00
9Supply installation of Out door Stand for Split Ac
unitsNos
5.00
10Supply installation of Out door Stand for Cassette
and Ductable Ac unitsNos
50.00
11Supply fabrication and installation of retangular
Ducts with necessary fittings
a 24 G Sq m 74.00
b 22 G Sq m 35.00
12Supply Installation testing and commissioing of
Duct Insulation with nesscessary item
a Thermal insulation 10 mm Nitrile rubber Sq m 109.00
b Acoustic insulation 12 mm thick Fibre glass Sq m 35.00
13Supply Installation testing and commissioning of
Grilles/Diffusers of standard reputed make
aAluminium powder coated Grilles / Diffuser with
damperSq m
7.50
b Supply and installation of GI duct damper Sq m 3.00
14Supply installation of Fresh air damper with bird
screen and cowl pieceNos
4.00
PAGE 44 of 79
BOQ FOR HVAC HIGH SIDE & LOW SIDE
Sl. No. Description Unit Qty Rate Amount
15 Canvas connection
Supply installation and commisioning of Fire
Retardent Flexible canvas connection at mouth
opening of the machine of reputed make as
approaved by architect.
Nos
2.00
Total HVAC
PAGE 45 of 79
1 Supplying fitting and fixing iron removal filter filling with
treated sand, pebbles, manganishdioxide and other required
materials of various filtration rate per hour of TARUS/
Equivalent make with all necessary fittings such as valve,bib
cock,pipe connection etc.with a free maintanance period of
six monthhs
(A) IRON REMOVAL FILTERS
Taurus make FRP Composite Structural vessel Iron Removal
Filters of 100 % rustproof vessels complete with Top &
bottom Strainers, Multiport Valves, Quality filter media-e.g
Treated Sand,Mno2 ,Barakar Sand Gravels & Pebbles. ISO,
NSF certified.
(VI) 10000 liters capacity Each 1.00
Total
BOQ OF IRON REMOVAL FILTER
SL. NO. Description Unit Quantity Rate Amount
PAGE 46 of 79
LAWN MAKING BY TURFING
1 Supplying and laying of selected grass turves [ size 60 cm x
30 cm] after preparing the land by removing of all unwanted
debrises ( rubbles, pebbles, plant roots etc.), mixing of
organic manure, levelling the surface and initial
maintenance by proper and periodic rolling, mowing and
irrigation etc.( as specified) for a period of six months from
the date of laying of grass including the application of
recommended dose of fertilizers(N:P:K) mixture as specified
and directed by the department.
(b) BY CARPET GRASS (Axonopus affinis) : sqm 150.00
TREE PLANTING
2 Supplying and planting of ornamental trees (1'-0" height
sapling) including pit making ( 60 cm x 60 cm x 60 cm ),
filling the pit with appropriate soil media, manure and
fertilizers as per specification and necessary maintenance for
a period of one year from the date of planting complete as
specified and directed .
Flowering Tree
(A) Gulmohar / Ashok each 4.00
(B) Kanchan each 4.00
BED PLANTING
BOQ FOR AREA DEVELOPMENT & LANDSCAPINGSL.
NO.
ITEM DESCRIPTION UNIT QTY Rate Amount
PAGE 47 of 79
BOQ FOR AREA DEVELOPMENT & LANDSCAPINGSL.
NO.
ITEM DESCRIPTION UNIT QTY Rate Amount
3 Supplying and planting of Dahlia / Chrysanthemum /
Gladiolus on the ground ( bed planting, bed size 45 cm x 45
cm x 45 cm) including the preparation of the soil, providing
organic manure and fertilizer, pesticides as per specification
and necessary maintenance for a period of 4 months from the
date of planting complete as specified and directed .
each 10.00
4 Supplying and planting of selected rose plants on the ground
(as specimen bush) including the preparation of the pit ( 45
cm x 45 cm x 45 cm ), removing unwanted debrises, filling
the pit with manure and fertilizers as per specification and
necessary maintenance for a period of 1year from the date of
planting complete as specified and directed .
(A) With Pompon Rose each 10.00
5 Preparation of a carpet bedding by raising the backside of
the bed to a height of 45 cm (average) after mixing organic
manure, fertilizer including supplying and planting of grass
and specimen plants (Brindavan) to engrave the desired
letters, necessary maintenance for a period of 6 months from
the date of planting complete as directed and specified by
the department.
sqm 20.00
SHRUB PLANTING
PAGE 48 of 79
BOQ FOR AREA DEVELOPMENT & LANDSCAPINGSL.
NO.
ITEM DESCRIPTION UNIT QTY Rate Amount
6 Supplying and planting of ornamental shrub ( below 1'-0"
height ) including pit making ( 60 cm x 60 cm x 60 cm ),
filling the pit with appropriate soil media, manure and
fertilizers as per specification and necessary maintenance for
a period of one year from the date of planting complete as
specified and directed .
(A) Radhachura / Krishnachura / Rat ki rani / Ixora / Jetuka each 5.00
(B) Allmanda / Khorika zai / May flower / Kamini /
Kathanda / Tecoma / Acalypha / Bougainvillea / Dracaena /
Togor / Nilakantha / Mussaenda
each 5.00
(C) Korobi / Azalea each 5.00
(D) Thuja each 5.00
(E) Poinsettia / Forget me not each 5.00
7 SHADE TREE
(A) Neem / Mahaneem / Beef wood / Bakul / Acacia / Siris
/ Devils tree / Kadam / Palash / Pink Cassia / peepal / Silver
oak / Simalu / Ajar
each 5.00
(B) Kanchan / Nahar / Arjunu each 5.00
(C) Sonaru each 5.00
(D) Bottle Brush / Nil Gulmohar / Debadaru / Weeping
Willow
each 5.00
(E) Ravenala each 5.00
(F) Paine each 5.00
(G) Christmas tree / Kuki each 5.00
POT PLANTING
PAGE 49 of 79
BOQ FOR AREA DEVELOPMENT & LANDSCAPINGSL.
NO.
ITEM DESCRIPTION UNIT QTY Rate Amount
8 Supplying and planting of terrestrial orchids with required
size of pot including filling the pot to the top surface with
appropriate soil media made of garden soil, river sand, cow-
dung, leaf mould, fertilizer, pesticides as per specification
and necessary maintenance for a period of 4 months from the
date of planting complete as specified and directed . (Mixing
of different ingredients of soil media to be made in presence
of Deptt. official / Specialist concerned)
(A) With Aeirides
. (I) Using earthen pot of 30 cm dia. each 5.00
(II) Using earthen pot of 60 cm dia. each 5.00
(III) Using concrete pot of 60 cm dia. each 5.00
Total
PAGE 50 of 79
1 Supply, Installation, Testing and Commissioning of Analogue Addressable
Multicriteria (optical smoke) detector with buit-in fault isolator, having open
digital protocol, alarm flag for fast alarm reporting, alarm address for fast location
of alarm, red LED alarm indication clear during quiescent state, operating
temperature -20°C to + 60 °C, humidity l0 - 95% RH (non condensing), digital
protocol for error free transmission, unique address mechanism for data storage in
the base to ensure high reliability all as per specifications etc as required .(Make:
Morley IAS, Gent, Esser, Bosch, Siemens /Edwards)
Each 414.00
2 Supply, Installation, Testing and Commissioning of Analoguel Addressable rate
of rise type Heat detector with built-in fault isolator, having open digital protocol
, alarm flag for fast alarm reporting, alarm address for fast location of alarm , red
LED alarm indication clear during quiescent state, operating temperature -20C to
+ 60 °C, humidity O - 95% RH (non condensing), digital protocol for error free
transmission, unique address mechanism for data storage in the base to ensure
high reliability all as per specifications etc as required . (Make: Morley IAS,
Gent, Esser, Bosch, Siemens, Edwards)
Each 8.00
3 Supply, Installation, Testing and Commissioning of Analogue Addressable loop
sounders with Strobe light having (continuous or pulsed tone, having output
power of 85-dB A at 1 meter, digital protocol compatible, etc as required. (Make:
Morley IAS, Gent, Esser, Bosch, Siemens, Edwards)
Each 17.00
4 Supply, installation, testing and commissioning of Analogue Addressable Pull
Down type Manual call Point suitable for reporting its addressees, interrupting
the loop and producing alarm in less than 0.2 seconds, complete with RED LED
as alarm indicator etc as required (Make: Morey IAS, Gent, Esser, Bosch,
Siemens, Edwards)
Each 32.00
BOQ FOR FIRE DETECTION SYSTEM
SL.
NO.
ITEM DESCRIPTION UNIT QTY Rate Amount
PAGE 51 of 79
BOQ FOR FIRE DETECTION SYSTEM
SL.
NO.
ITEM DESCRIPTION UNIT QTY Rate Amount
5 Supply, Installation, testing and commission of Analog Addressable Single Input
Monitor Modules complete in all respect (Make: Morley IAS, Gent, Esser, Bosch,
Siemens, Edwards)
Each 46.00
6 Supply, installation, testing & commissioning of Micro processor based 2 wire
fault tolerant loop, networkable type, with each loop capacity of minimum 99
detectors and 99 modules, fire alarm/detection control panel. The panel shall be
able to give location of all fire/fault conditions of addressable units via the
address codes. Further, the panel must be able to automatically switch ON /OFF
respective control module when ever any alarm is triggered. The panel shall have
rectifier, Loop cards, minimum 8O character L C D unit to indicate Fire/Fault
Signal with address and analog output, external/inbuilt printer to log all fire or
fault [events complete in all respects. The Panel Shall housed in a Powder coated
CRC enclusure selaed to IP30. The Panel Shall have 20 Zones with Individual
LED Indicators, expandable to 80 LED Indicators. The Panel Shall have 3 Serial
Ports. The panel shall have a built in power supply and battery charger along with
maintenance free 24 AH, 2 x 12 volt SMF Lead acid batteries capable of running
for a minimum of 24 hours with battery charger complete as required and as per
specifications conforming to BS5839 Standards and Duly Approved by
/EN54/LPCB/VDS. (Make: Morley IAS, Gent, Esser, Bosch, Siemens, Edwards,
Copper)
6.1 Loop Capacity as per all required no of devices plus 20% spare loop capacity. Nos. 2.00
7 Supplying, drawing, connecting, testing & commissioning of 2 core x 1.5 sq.
mm. multi stranded copper conductor, pvc insulated PVC sheathed,
aluminium myler tape shielded, Armoured cable suitable for Fire Alarm
System.(Make: Havels, Polvacb, Crvstal, Gloster, Finolex)
Mtr. 500.00
8 Supply, installation, testing & commissioning of Led Exit Signs with inbuilt
Lithium Ion Battery Backup suitable for 230 volts, 1 Phase, 50Hz operation
(Make: Agni, Legrand, prolite)
8.1 Single Sided Nos. 26.00
PAGE 52 of 79
BOQ FOR FIRE DETECTION SYSTEM
SL.
NO.
ITEM DESCRIPTION UNIT QTY Rate Amount
9 Supply, Installation, testing and commissioning of Control module for hooter
complete in all respect.
Nos. 10.00
10 Supply, installation, testing & commissioning of response indicator. Nos. 231.00
Total
PAGE 53 of 79
1 Providing and fixing black steel pipes for Internal Hydrant Piping to
I.S. 1239 (Heavy class) including all fittings like, couplings, blends.
elbows unions , tees, flanges, as per table “E” reducers, offsets etc.
making connections, all types of welded or screwed joints as per
specifications and making connections required, including cutting
holes and chases in brick or RCC walls and making good complete.
After completion of the piping work the entire pipe line will be
hydraulically tested for a pressure of 10kg/cm2 for a period of 48
hours. The final pipe line will be painted with two or more coats of
synthetic enamel paint of first grade as per IS specifications over
one coat of red oxide zinc chromate primer including necessary
surface preparation complete. The work will be carried out as per
specification and drawings and as directed by the consultant.
(Make:Tata/Jindal/Nezone)
1.1 100 mm dia NB Mtr. 80.00
1.2 80 mm dia NB Mtr 12.00
2 Proving and fixing ISI marked Gunmetal fire valve 80mm single
outlet with control valve and fitted with 63 mm dia instantaneous
female coupling at the outlet complete including companion flanges
as per table “E” gunmetal blank cap and chain, nuts, bolts and 3mm
thick compressed asbestos gasket at locations as per drawings (inlet
flange to I.S.5290-1969 Class C) (Make: Newage/Swati/Sukan/M-
Tech)
Each 10.00
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
PAGE 54 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
3 Providing and fixing first aid fire hose reel drum wall mounting,
swinging type fitted with 20mm dia 30mm long high pressure type II
hose to I.S. 5132 with 5 mm outlet gunmetal nozzle with shut off
valve (I.S. 884-1969). Name of manufacturer should be embossed on
the drum as well as on hose. (Make: Newage/Swati/Sukan/ M-Tech)
Each 10.00
4 Providing and fixing 63 mm dia 15 mm long rubberlined fabric hose
including gunmetal male and female instantaneous type coupling
approved by fire authority, machine would with copper wire
complete in all respects. Hose shall conform to I.S. 636 type II and
coupling to I.S. 903-1975 with ISI certification (Two per each single
landing valve) (Make: Newage / Swati/ Sukan/M-Tech)
Each 20.00
5 Providing and fixing standard short size gunmetal branch pipe with
gunmetal nozzle 16 mm dia oitlet with standard instantaneous type
63 mm dia coupling (ISI marked) (Make : Newage / Swati/ Sukan/M-
Tech)
Each 10.00
6 Providing and fixing standard fireman’s axe with heavy insulated
rubber handle tested for 20000 volts confirming to IS:926 (Make :
Newage / Swati/ Sukan/M-Tech)
Each 10.00
7 Proving & fixing gunmetal fire brigade inlet with 63 mm dia
instantaneous type inlet and 150 mm dia flanged outlet with built in
check valve for fire brigade connection to underground tanks and
fire risers (I.S. 904-1965) tested for 20 kg/cm2 pressure complete in
all respects with companion flanges, nuts, bolts, gaskets, etc. (Make
: Newage / Swati/ Sukan/M-Tech)
7.1 Two way Each 2.00
PAGE 55 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
8 Providing and fixing gunmetal single acting air release valve with
screwed inlet 25 mm dia as per IS 12992 rated for 20Kg./Sq.cm
(Make :SB/ Newage / Swati/ Sukan/M-Tech)
Each 2.00
9 Providing and fixing SS/ Brass ball valve full bore type tested for 20
Kg/Cm2 with lever and screwed female ends (Make:
Kitz/Zolloto/Jet)
Each 10.00
10 Providing and fixing cast iron butterfly valves of PN 1.6 rating
complete with bolts, nuts, 3 mm thick compressed asbestos gasket,
companion flanges as per table “E” complete in all respects. (Make :
Advance / Intervalve/ Audco/Kartar)
10.1 100 mm dia with lever Each 4.00
11 Providing and fixing C.I. horizontal dual plate wafer type non return
valves PN 1.6 including washer, nuts, bolts, 1.5 mm thick
compressed asbestos gasket companion flanges as per table “E”
complete (Make: Advance / Intervalve/ Audco/Kartar)
11.1 100 mm dia Each 4.00
HAND APPLIANCES
Note: All extinguishers shall carry ISI mark.
1 Providing and fixing Carbon di-oxide fire extinguishers consisting
of welded M.S. cylindercal body, squeeze lever discharge valve 30
cms long high pressure discharge hose, discharge nozzle, suspension
bracket, ISI marked as per IS:10204 finished externally with red
enamel paint and fixed to wall with brackets complete with internal
charge. (Make: Ceasefire / Steelage/Lifeguard).
1.1 Capacity 9 Kg. (Pump Room & DG Set) Each 2.00
SECTI
ONS C
PAGE 56 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
2 Providing and fixing stored pressure ABC Fire Extinguisher
consisting of welded M.S. cylindrical body, squeeze lever discharge
valve 30 cms long high pressure discharge hose, discharge nozzle,
suspension bracket, ISI marked as per IS: 13849 finished externally
with red enamel paint and fixed to wall with brackets complete with
internal charges. (Make: Ceasefire /Steelage/Lifeguard)
2.1 Capacity 6 kg. Each 24.00
3 Providing and fixing Carbon-dioxide fire extinguishers consisting of
welded M.S cylindrical body, squeeze lever discharge valve fitted
with internal idischargetube,30cms long high pressure discharge
hose, discharge nozzle, suspension bracket, confirming to IS : 2878
finished externally with red enamel paint and fixed to wall with
brackets with rawl plug/ dash fasteners complete with internal
charge.(Make: Ceasefire /Steelage/Lifeguard)
3.1 Capacity 4.5 Each 8.00
PUMP AND ACCESSORIES
1 Supply, installation, testing and commissioning of electrically
driven high pressure centrifugal fire hydrant /sprinkler pump,
suitable for automatic operation consisting of the following: (Make:
Grundfos /Wilo / Kirloskar)
SECTI
ON D
4 Providing and fixing at approved location approved make 4 nos. fire
buckets of 24 gauge galvanized steel, painted white inside and red
Set 1.00
PAGE 57 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
a. Horizontal, split casing, Multistage centrifugal pump, suitable
for operation on 415 volts at 6%, 3 phase, 50 HZ AC supply. The
installation shall be complete with flexible coupling and coupling
guard as required. Fire pump shall have CI casing, CS diffusers,
bronze impeller (hard finished and dynamically balanced) and SS
(304) shaft with mechanical seal, capable for delivering 1650 LPM
at outlet head 70 mts to ensure a minimum pressure of 3.5 Kg/Sqcm
at the farthest or topmost hydrant / sprinkler. The installation shall
be complete with necessary pressure gauge with gun metal shut off
cock on delivery side (The pump should be tested and assembled for
bench mark at factory).
b. Pump shall be capable of furnishing not less than 150% of rated
capacity at a head of not less than 65% of the rated head. The shut
off head shall not exceed 120% of rated head.
c. Squirrel cage induction motor, TEFC type
suitab0lelIorSolpelraEn on 415 volts, 3 phase 50 HZ A.C supply, for
the above pump with synchronous speed of 2900 RPM, conforming
to IP 55 protection & class F insulation. The motor shall conform to
IS 325-1978 (up to date) with flexible coupling and coupling guard,
complete as required.
d. Common base plate for (a) and (b) from M.S. Channel for
required size.
e. Suitable cement concrete foundation with cement concrete
plaster (design and drawing to be provided by the Contractor which
will be duly approved by the consultant before construction)
complete with anti-vibration arrangement of cushy foot mountings.
PAGE 58 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
f. The rate includes interconnecting cables, foundations &
foundation bolts.
Set 1.00
2 Supply, installation, testing and commissioning of Diesel Engine
Driven fire pump suitable for automatic operation comprising of the
following and conforming to BS 649/IS 10002 all amended upto
date. (Make: Grundfos/Wilo/Kriloskar)
a. Horizontal, split casing, high pressure multistage; centrifugal
pump, suitable for operation on 415 volts ± 6%, 3 phase, 50 HZ AC
supply. The installation shall be complete with flexible coupling and
coupling guard (as per safety norms enclosed), as required. Fire
pump shall have CI casing, CS diffusers, bronze impeller (hard
finished and dynamically balanced) and SS (304) Shaft with
mechanical seal, capable for delivering 1650 LPM at low zone
outlet head of 70mts to ensure a minimum pressure of3.5 Kg/Sqcm
at the farthest or topmost hydrant / sprinkler. The installation shall
be complete with necessary pressure gauge with gun metal shut off
cock on delivery side. (The pump should be tested for bench mark at
factory and shall be gotten approved by the Local fire Authority).
Pump shall be capable of furnishing not less than 150% of rated
capacity at a head of not less than 65% of the rated head. The shut
off head shall not exceed 120% of rated head.
PAGE 59 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
b. Radiator cooled diesel engine of speed 1800 RPM suitable for
the above pump with automatic starting mechanism and other
accessories including, fuel tank (fabricated from 3mm MS sheet,
painted with two coats of synthetic enamel paint over a coat of
primer) of capacity adequate to sustain pump operation for 8 hours
continuous working. The tank shall be fitted with Magnetic oil level
indicator, MH with cover, drain valve, air vent/including structural
supports (painted with approved shade), 2 Nos. x 12 volt battery,
flexible coupling, coupling guard & exhaust pipe connection
complete as required.
c. Common base plate for (a) and (b) from MS channel of
required size.
d. Suitable cement concrete foundation with cement concrete
plaster (design and drawing to be provided by the Contractor which
will be duly approved by the consultant before construction)
complete with anti-vibration/ arrangement of cushy foot mounting.
Set 1.00
3 Supply, installation, testing and commissioning of jockey pump
(pressurisation pump) comprising of the following:(Make: Grundfos
/Wilo /Kirloskar)
a. Vertical Multistage, centrifugal pump, suitable for operation on
415 volts ± 6%, 3 phase, 50 HZ A.C supply. The installation shall
be complete with Flexible coupling and coupling guard, complete as
required. Jockey pump shall be of stainless steel construction.
PAGE 60 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
The pump head and base shall be CI GG20 construction and
impellers, difusers, shaft sleeve, seal bush & pump shaft shall be in
SS 304 material. The pump shall be provided with mechanical seal
The system shall be complete with necessary pressure gauge with
gun metal shut off cock on delivery side (The pump should be tested
and assembled for bench mark at factory.
b. Squirrel cage induction motor TEFC type for operation on 415
V, 3 phase so HZ AC supply for the above pump with a synchronous
speed of 2900 R.P.M. with flexible coupling and coupling guard etc.
as required.
c. Common base plate for (a) and (b) from M.S. channel as
required size.
d. Suitable cement concrete foundation with cement concrete
plaster (design and drawing to be provided by the Contractor which
will be duly approved by the consultant before construction)
complete with anti-vibration/ arrangement of cushy foot mounting.
For pump defined above & of duty as follows:
Hydrant & sprinkler System
Flow: 180 LPM
Head: 70 mts. Set 1.00
4 Providing & fixing MS Class 'C' diesel engine exhaust pipe
(including al fittings, clamps, steel support) of suitable dia for the
engine. The pipe shall be provided with 12 mm thick supercera
ceramic fibre rope.
RM 6.00
PAGE 61 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
5 Providing fitting, testing and commissioning of epoxy coated MS
body precharged air vessel 150 Ltr capacity having a pressure rating
of 1.6 Bar for pressurization of hydrant / sprinkler system complete
in all respect with valves to operate as per operating sequences
including 25 mm dia drain valve, air release valve with stop cock on
the top, 25 mm dia inlet with isolating valve duly painted from
inside and outside complete as required. (MAKE: Pentair or
approved equal) (note: the pressure vesser must be precharged as per
calibrated and calculated pressure level)
Set 1.00
6 SITC of Pressure gauge Each 3.00
Supply, installation, testing & commissioning of 100 mm dia
Bourden type Stainless Steel dial type glycerline filled pressure
gauge including brass isolation valve and pipe having calibration of
0-16 Kg/Cm2. (Make : H Guru/ Feibig)
7 Providing and fixing welded pipe suction header upto 6 mtr. long
with two inlet. All outlets and ends with flanged connections, blank
flanges as required including painting with one coat of red oxide
primer and two or more coats of synthetic enamel paint to give an
even shade.
7.1 250mm x 6 mm thick -200 mm x 1 inlet; 200mm x 2 outlet; 100mm
x 1 outlet
Nos. 1.00
7.2 200mm x 6 mm thick – 150mm x 2 inlet; 80mm x 1 inlet; 150mm x
1 outlet.
Nos. 1.00
8 Providing and fixing Gun Metal Foot Valve including washer, nuts,
bolts 1.5mm thick compressed asbestos gasket companion as per
table.
8.1 200 mm dia Nos. -
PAGE 62 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
9 Providing and fixing C.I. horizontal dual plate wafer type non return
valves PN 1.6 including washer, nuts, bolts, 1.5 mm thick
compressed asbestos gasket companion flanges as per table “E”
complete. (Make: Advance/ intervalve/ Audco)
9.1 150 mm dia Each 2.00
9.2 80 mm dia Each 1.00
10 Providing fixing MS structural work fabricated from standard
sections, eg., MS rounds, angles, channels, including cutting to size,
drilling, welding, fixing and welding to insert plates in RCC
structural members as directed (by the engineer-in-charge including
cutting and making good the walls and [floors (for Pipe Support
Structures & Cable tray.)
Kg. 200.00
11 Providing and fixing cast iron butterfly valves of PN 1.6 rating
complete with bolts, nuts, 3 mm thick compressed asbestos gasket,
companion flanges as per table “E” complete in all respects. (Make:
Advance / Intervalve/Audco)
11.1 80 mm dia with lever Each 1.00
11.2 100 mm dia with lever Each 1.00
11.3 150 mm dia with Each 2.00
11.4 200 mm dia with lever Each 2.00
12 Providing and fixing SS/Brass Ball Valve full bore type tested for
20 Kg/Cm2 with lever and screwed female (MakeKitz/Zolloto)
12.1 25 mm dia full bore type Each 3.00
13 SITC of pressure switches
PAGE 63 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
supp1y, installation, Testing and commissioning of pressure
switches suitable for operating with fire hydrant systems for
working pressure of 14.0 Kg/cm2 including electrical control wiring
with suitable copper conductor PVC insulated and sheathed control
cable upto control panel, connections etc. complete as required.
[Make: indfoss or approved equal)
Each
Section
E
ELECTRICAL INSTALLATION FOR FIRE PROTECTION
SYSTEM
1 Design, fabrication, assembling, wiring, supply, installation, testing
and R commissioning of motor control centre shall be fabricated out
of 14 gauge, CRCA sheet steel in form in 3b formation with
reinforcement of suitable size/angle iron, channel "l" sections irons
and / or flats wherever necessary. Cable gland plates shall be
provided on top as well as at the bottom of the panels. Panels shall
be treated with all anticorrosive process before painting as per
specifications with 2 coats of red oxide primer and final approved
shade of powder coated paint. 2 Nos. earthing terminals shall be
provided for 3 phase, 4 wire, 50 Hz supply system. Lifting hooks
shall also be provided in case of large panels. Approval shall be
taken for each panel before fabrication. Cadmium Plated hardware
shall be used in fabrication of panels. Quoted rates shall inclusive of
cables, cable trays, earthing [in accordance to specification] with
earthing from panel to each motor / equipment. [Comonents make:
L&T, Schneider, ABB, Siemens, Hager, Legrand; Panel maker must
be CPRI approved panel maker) The panel will be constructed only
after approval of Panel makers electrical sld, control sld and GA
drawings by the consultant)
PAGE 64 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
MCC for Fire Fighting equipments
a. 1 no. 400 amps 4 pole mechanical interlocked incoming
MCCB complete with the following
i. 0-500 volts 96 x 96mm square voltmeter with selector switch
shall be protected by 2 amp TP MCB 1 set
ii. 0-400 amps 96 x 96mm square ammeter with 400/5 amp 15
VA CL:1 Ct’s and selector switch 1 set
iii. Phase indicating lamp shall be protected by 2 amp MCB 1 set
a. Aluminium bus bar sleeves type, rated at 500 amps for three
phase and inertial phase bus bar shall have maximum current
density of 1 amps/sq.cm. and the neutral bus bar of not less than
50% capacity.
Outgoing
a. 1 N0. 250 amps TPN MCCB outgoing feeders with 75KKW
DOL starters out going feeders to Hydrant / Sprinkler pump motor.
The compartment shall contain CT operated ammeter of 0-400
amps range with selector switch auto / manual selector switch and
indicating lamp with MCBs for with MCBs for “ON”/OFF” TRIP’
status of motor.
b. 1 N0. 32 amps TPN MCCB, 7.5 KW Direct online starter with
single phase preventer and outgoing feeder to jockey pump motor.
The compartment shall contain CT operated ammeter of 0-30 amps
& indicating lamps with 1MCBs for “ON”/0FF”TRlP’ status of
pump motors.
PAGE 65 of 79
BOQ FOR FIRE FIGHTING SYSTEMSL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
c. Providing and fixing 1 No. auto start panel activated with
pressure switch 1 for diesel engine complete with all accessories,
batteries, battery charger of, suitable rating, MCB timers, push
buttons, microprocessor based alarm; annunciator, wiring and
cabling including connection to diesel engine complete as required
ready for working.
d. Necessary cable alleys space for spare switches, internal
wiring and copper earthing of all equipment shall also be included.
All switch gears/Control gears shall be motor duty rating.
Note: All NCCN’s be suitable for motor duty and shall be of 36 KA
breaking capacity.
Provision shall be made for providing potential free contacts to all
pumps starters for connection to building automation system.
MCC as described above Set 1.00
Total
PAGE 66 of 79
1 Partition
A Providing and fixing of ready for primer and paintable surfaced 72mm drywall partition
using non asbestos, non combustible, SHERA Make or Equivalent fibre cement boards
made of recycled fibres and cement as raw materials manufactured by wet recessed
autoclaved technology with density of 1300Kg/m3 as per (ASTMC 1185). The SHERA
make or Equivalent make G.I. frame of thickness 0.60 consists of steel metal stud frame
of size 50mm having one flange of 41mm and other of 44mm placed @ every 600 mm c/c
in vertical direction upto soffit and horizontally at board joints.These studs are placed at
floor and ceiling channels of 52mm width and 0.60 mm thick and having equal flanges of
32 mm. The floor and ceiling channels are fixed to floor and soffit using fastners at every
600mm c/c. A horizontal frame section is placed at every 1200mm c/c. Next one layer of
10mm thick fibre cement board are fixed in staggered joints on either side of the studs to
avoid leakage through joints. These boards are joined using Specified “type S” Self
tapping SS W 25 / 3.5 x 25mm corrosion resistant drywall steel screws spaced at 200mm
centers on all joints and 300mm centers in the field of boards. Screw fixing is done
mechanically. Finally, boards and screw heads are to be jointed and finished with epoxy
putty so as to have a flush look which includes filling tapered edge and square edges of
board with SHERA make or Any equivalent cement based joining compound and fibre
tape .
sqm 249.00
B Extra for providing Twiga Insul glass wool mat backing with chicken mesh cover of
Twiga Fibre Glass insulation as specified and directed at all levels.
50mm thick Sq.m. 249.00
C Providing & fixing Fixed glazed partition fabricated with 12mm thk toughened glass all
sides edge polished to be fixed on patch fittings of Dorma / D'Line make. Rate should be
inlusive of patch fitting(s), all complete, inclusive of etching film on the glass as per
design and necessary holes to be drilled in the glass .
Sq.m. 41.00
2 Wall Panelling
Providing, fitting and fixing 12mm thick BWP board panelling of make Archidply/
Greenply or Equivalent ,over 30x50mm sectional frame work made out of BWP board
embeded in cement sand mortar in prop1:3 and spaced 450mm to 600mm apart complete
with counter sunk wood screw of 50mm length.
Sqm 757.00
3 Finishing on Wall Panelling
BOQ FOR INTERIOR AND ALLIED WORK
SL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
PAGE 67 of 79
BOQ FOR INTERIOR AND ALLIED WORK
SL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
A Providing and fixing 1.5mm thk Laminate of approved make Marino/ Archidply/
Greenply or Equivalent of approaved color and shade over Ply paneling /
partitions/Block board Door Shutters etc as indicated in drawings or as per the
instructions of the Architects. The Contractor has to follow the exact procedure to paste the
laminate as per Company's Specification.
Sqm 737.00
B Supplying, fitting and fixing SoundSoak NSS Cord (FSS Cord) wrapped acoustical wall
panel system of Armstrong OPTRA high acoustical wall panelling with fibre glass
substrate 25 MM thick. Including all fixtures and fittings.
Sqm 153.00
4 Door frame(Chowkhat) and Door Panels
A Providing dressed wood work in post, walls,battens, post plate bressumers etc.
including supplying and fixing with spikes, nails,bolt and nuts of 12mm dia(M.S) and
required length etc.complete with kiricide oiling two coats to faces in contact with C.C or
masonry (M.S flats, angle cleats and bolt and nuts required for flats,angle cleats
wherever use shall be measured and paid separately)
cum 3.75
B Providing, fitting and fixing 6 mm thick Water Proof Ply board of make Archidply/
Greenply or Equivalent ,over Existing/ New Wooden Door Frame in Proper Line and
Level to make ready for Fixing Laminate / Vaneer complete in all respect as per design.
Sqm 122.00
C Double leaf glass door - Frameless
Providing & fixing double leaf glazed door fabricated with 12mm thk toughened glass all
sides edge polished to be fixed on patch fittings of Dorma / D'Line make. Cost of the door
to be inclusive of pre-approved 600mm long handles to be fitted horizontally / vertically as
per dwgs or instructions & patch fitting(s), lock(s), all complete, inclusive of Birla 3M
etching film on the glass as per design and necessary holes to be drilled in the glass for
Access control locks,
Double leaf door ( of size 1800mm x 2100mm ) nos 17.00
D Single leaf glass door - Frameless
Providing & fixing single leaf glazed door fabricated with 12mm thk toughened glass all
sides edge polished to be fixed on patch fittings of Dorma / D'Line make. Cost of the door
to be inclusive of pre-approved 600mm long handles to be fitted horizontally / vertically as
per instructions & patch fitting(s) lock(s), etc., all complete inclusive of Birla 3M etching
film on the glass as per design and including making necessary holes in the glass for
Access control locks,
PAGE 68 of 79
BOQ FOR INTERIOR AND ALLIED WORK
SL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
d1 size 1200mm x 2100mm nos 12.00
d2 size 1000mm x 2100mm nos 12.00
d3 900mm x 2100mm nos 2.00
E BLOCK BOARD SHUTTERS
Providing and fixing flush door shutters solid core construction with frame of 1st class
hard wood with cross band and face veneered ply wood face panels conforming to relevent
I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with
necessary wood screws.
b) Non decorative type and block board core. 30 mm thick 84.88
F Louvered Shutter
Providing 1st class local wood (Hollock/Bonsum)ventilating louvre in 50mm x 38mm size
wooden frame with 150mm x 20mm slate made of 1st class local wood including fitting
and fixing with nails and painting with two coats of kiricide oiling complete. (i) 1st class
local wood
sqm 52.00
G Fire Rated Door with Panic Bar
Supply, Fitting , Fixing of Fire Door of clear opening 1.2mx2.0m opening Steel
Composite Light weight single swing asbestos free Fire Proof doors of 60 minutes fire
rating conforming to norms at per CBRI Grade. Comprising of welded box section
insulated frame and Fully Insulated shutters faced with 18 SWG C. R. sheet both sides
with all steel work primed with fire retardant anti-corrosive primer of Approaved brand .
Rate should include cost of Door frame properly jammed to RCC Stiffner/ Brick Wall as
directed by Architect. ( Rate to include all hardware fittings including Panic Bar ,
complete in all respect to the satisfaction of the client and Architect.)
sqm 31.70
H Trap Door
P/F Trap doors to house AC ductable units, made out of 50mm x 12.5mm TW frame and
19mm thk BWP consisting of openable panels. The shutter to be finished in 1.0mm thk
laminate of approved shade and color, on inside and outside, and all wooden members
shall be finished matching the Ceiling.
sqm 17.00
5 Tables
PAGE 69 of 79
BOQ FOR INTERIOR AND ALLIED WORK
SL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
a Providing , supplying ,Fitting and fixing L-shaped Reception table of Size 2.4 (L1) x
2.1m (L2)x 0.6m (Top)x 0.75/ 0.9 m (ht) with 9 nos. 0.42x0.2mm Drawers below counter
made out of 19mm BWP board and finished with 1.5mm thick Laminate of Approaved
Brand and Shade. The Top/ Designed Masking Surface finished with 6mm thick. PVC
solid surface on all visible sides as per Design and Specification complete in All respect
including all hardware as directed by the Architect.
Each 1.00
b Providing , supplying ,Fitting and fixing L-shaped Help Desk table of Size 2.1 (L1) x
1.6m (L2)x 0.6m (Top)x 0.75/ 0.9 m (ht) with 6 nos. 0.42x0.2mm Drawers below counter
made out of 19mm BWP board and finished with 1.5mm thick Laminate of Approaved
Brand and Shade. The Top/ Designed Masking Surface finished with 6mm thick. PVC
solid surface on all visible sides as per Design and Specification complete in All respect
including all hardware as directed by the Architect.
Each 2.00
c Providing , supplying ,Fitting and fixing Director's table of Size 3.0 x 1.2 x 0.75 (ht)
with 3 nos. 0.42x0.2mm Drawers below counter made out of 19mm BWP board and
finished with 1.5mm thick Laminate of Approaved Brand and Shade. The Top/ Designed
Masking Surface finished with 6mm thick. PVC solid surface on all visible sides as per
Design and Specification complete in All respect including all hardware as directed by the
Architect.
Each 1.00
d Providing , supplying ,Fitting and fixing Asstt Director's table of Size 2.4 x 0.9 x 0.75
(ht) with 3 nos. 0.42x0.2mm Drawers below counter made out of 19mm BWP board and
finished with 1.5mm thick Laminate of Approaved Brand and Shade. The Top/ Designed
Masking Surface finished with 6mm thick. PVC solid surface on all visible sides as per
Design and Specification complete in All respect including all hardware as directed by the
Architect.
Each 3.00
e Providing , supplying ,Fitting and fixing Director's Sec. table of Size 1.6 x 0.6 x 0.75
(ht) with 3 nos. 0.42x0.2mm Drawers below counter made out of 19mm BWP board and
finished with 1.5mm thick Laminate of Approaved Brand and Shade. The Top/ Designed
Masking Surface finished with 6mm thick. PVC solid surface on all visible sides as per
Design and Specification complete in All respect including all hardware as directed by the
Architect.
Each 1.00
PAGE 70 of 79
BOQ FOR INTERIOR AND ALLIED WORK
SL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
f Providing , supplying ,Fitting and fixing Conference Table of top 5.1x1.6 mtr made out
of 19mm BWP board and finished with 1.5mm thick Laminate of Approaved Brand and
Shade with Top Surface finished with 6mm thick. PVC solid surface as per Design and
Specification complete in All respect including all hardware including POP up boxes for
Power and LAN Sockets as directed by the Architect. The Rates should be quoted on the
basis of Table Top Surface Area.
Each 1.00
g Providing , supplying ,Fitting and fixing Desk of Size 1.8x 0.6m (Top)x 0.75/ 0.9 m (ht)
with 3 nos. 0.42x0.2mm Drawers below counter made out of 19mm BWP board and
finished with 1.5mm thick Laminate of Approaved Brand and Shade. The Top/ Designed
Masking Surface finished with 6mm thick. PVC solid surface on all visible sides as per
Design and Specification complete in All respect including all hardware as directed by the
Architect.
Each 1.00
h Providing , supplying ,Fitting and fixing Dining Table of top 3x1.2 mtr made out of
19mm BWP board and finished with 1.5mm thick Laminate of Approaved Brand and
Shade with Top Surface finished with 6mm thick. PVC solid surface as per Design and
Specification complete in All respect including all hardware as directed by the Architect.
Each 1.00
6 Cabinet
A Providing , supplying ,Fitting and fixing 750/ 1200 mm high and 600mm deep Storage
cabinets made out of 19mm BWP board of make Archidply/ Green/ Century or
Equivalent and finished with 1.5mm thick Laminate of Same make . The Top Surface
should be finished with 6 mm thick PVC Solid Surface of Marino, green or Equivalent of
approaved brand , colour and specification as per design. The Rate Should Include Cost of
White Base Laminate pAsted inside of the Cabinet. Rates should be quoted on front
surface area of the cabinet.
sqm 33.60
B Providing , supplying ,Fitting and fixing 450-600 mm deep Full ht Customised Fully
Laminated Wall Storage cabinets with shutter made out of 19mm BWP board of make
Archidply/ Green/ Century or Equivalent and finished with 1.5mm thick laminate of make
Archidply/ Marino/ GreenLam or Equivalent of approaved brand , colour and
specification as per design. The Rate Should Include Cost of White Base Laminate pAsted
inside of the Cabinet. Rates should be quoted on front surface area of the cabinet.
sqm 219.50
7 Vertical Blinds on Windows
Supplying, fitting and fixing MAC blinds horizontal and vertical complete as specified
and directed by the department at all levels.
PAGE 71 of 79
BOQ FOR INTERIOR AND ALLIED WORK
SL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
(A) Vertical blinds
(a) Regular
i) 100 mm Sqm 320.00
8 Providing , supplying ,Fitting and fixing 400mm Raised Plateform in Training Hall as
Stage made out of MS Angle Frame with 30mm Block Board Top in Proper Line and level
. The Surface should made ready for laying Wooden Block Flooring , as directed and
specified by the Architect.
Sqm 40.00
9 Supply and Laying of high pressure laminated Anti static false flooring of 300mm height
including making necessary step of 150mm height in entry level with skirting and garter as
required to make the room finish estatic with the other tiled portion.
Sqm 110.00
10 Providing and laying Imported Loop pile patterned carpet 24-26 OZ. in Roll/Tile form
(Available tile sizes 900mm x 900mm / 450mm x 450mm) with antistatic rating of <3.5,
PVC/ Eco-friendly backing and having guage of 1/10- 1/12 as per the selection of the
architect. Carpet to be of pile composition of Nylon of Dupont / Deftron / Colorfast /
Wearon or other equivalent make confirming to relevant BS standards. The rate shall be
inclusive of plastic sheet covering and protecting the carpet till instructed to remove the
same by the architect.
Sqm 231.00
Total
PAGE 72 of 79
1 Providing, supplying and installation Modular Workstation with 1.2m Partition Height of
Make Fetherlite NEO 50, Godrej , HNI or any Equivalent Brand Matching SPecification of
25mm Thick Pre laminated Table Top with 2mm Edge Lipping with 50mm Frame, covered
with Glass Marker and Megnetic Febric Board on main Frame and Febric Tile on Return and
End Frame above the Table Top. The Workstation should be supplied and installed in
complete in respect alongwith Separate Raceways for Power and Data below the Table Top
and Skirting Level as directed by the Architect. Rate should include cost of One no Mobile
Padestal of size 400 (w)x465(D)x640(H) , one No Key Board Tray with Mouse Pad and CPU
Trolly as per Specification.
a. Linear Workstation of Size 1.2x0.6x0.75m Each 12.00
b. Angular Workstation of Size 1.8x1.8x0.75m Each 2.00
c. Cublicle with Size 2.7/2.3 x0.6x0.75m Each 2.00
2 Providing, supplying and installation Modular Meeting Table of Make Fetherlite , Godrej ,
HNI or any Equivalent Brand Matching SPecification of 25mm Thick Pre laminated Table
Top with 2mm Edge Lipping with Gable End Support and Modesty Panel. The Table should
be supplied and installed in complete in respect alongwith 2 nos. of Flip Up 300 with
Provision for Switch Cut out for Power and Dtata cable Management as per Specification.
a. Size 2.4x0.9x0.75(ht) Each 2.00
b. Size 3.0x0.9x0.75 (ht) Each 1.00
C. Size 0.9x0.9x0.75(ht) Each 3.00
3 Providing, supplying and installation Modular DIAS (Seminar hall) Table 3.9x0.9x0.75m of
Make Fetherlite , Godrej , HNI or any Equivalent Brand Matching SPecification of 25mm
Thick Pre laminated Table Top with 2mm Edge Lipping with Gable End Support and
Modesty Panel. The Table should be supplied and installed in complete in respect alongwith 3
nos. of Flip Up 300 with Provision for Switch Cut out for Power and Dtata cable Management
as per Specification.
Each 1.00
4 Providing, supplying and installation Modular Cafetaria Table 0.9x0.9x0.75m of Make
Fetherlite , Godrej , HNI or any Equivalent Brand Matching SPecification of 25mm Thick
Pre laminated Table Top with 2mm Edge Lipping with Undestructure made out of Powder
Coated Prong Leg as per Specification.
Each 0.00
BOQ FOR MODULAR FURNITURE SL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
PAGE 73 of 79
BOQ FOR MODULAR FURNITURE SL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
5 Providing, supplying and installation Modular Class Room Type Composite Chair and
Table of Make Fetherlite Model TC 930 , Godrej , HNI or any Equivalent Brand with 25mm
High Pressure laminated finish Table Top. The Seat and Back should be made out of
vernished Multi layer wood Vaneer shaped by Mould with All Supports below and Book case
, made with Electro static powder coated Steel with Spring return Tie up Machanism as per
Design and Specification as directed by the Architect.
a. 3 seater with Desk for Front Module or Row. Each 2.00
b. 3 Seater with Seat and Desk for Middle Module or Row. Each 7.00
c. 3 seater with Seat for Rear / Last Module or Row. Each 2.00
6 Providing, supplying and installation of 1.2x0.6x0.42(h) Chrome framed Glass top Center
Table of Make Fetherlite Model Verve Glass 610-FL , Godrej , HNI or any Equivalent Brand
as per Design and Specification as directed by the Architect.
Each 7.00
7 Providing, supplying and installation of Storage Cabinet made out of 25mm Storage Top and
Rest with 18mm Pressure laminated Board complete in all respect with openable shutter, Auto
Closing hinges, Adjustable Shelves, Recessed Handles and Lockinh mechanism as per
Design and Specification as directed by the Architect.
A. 0.6x0.45x1.20(h) Each 0.00
A. 0.9x0.45x1.20(h) Each 15.00
A. 1.0x0.45x1.20(h) Each 5.00
TOTAL
PAGE 74 of 79
1 Providing, supplying and installation Nylon Base Medium Back Permanent Contact,
Revolving and Tilting Chair with Fixed Arms of Make Fetherlite Advantage MB, Godrej ,
HNI or any Equivalent Brand as per Specification and Colour as directed by the Architect.
( For Linear Workstations and Library)
Each 18.00
2 Providing, supplying and installation Nylon Base Medium Back Mesh Back Permanent
Contact, Revolving and Tilting Chair with Fixed Arms and Synchro mechanism of Make
Fetherlite Contact , Godrej , HNI or any Equivalent Brand as per Specification and Colour
as directed by the Architect. ( For Angular Workstations and director's PA)
Each 2.00
3 Providing, supplying and installation Nylon Base Medium Back Mesh Back Hight
Adjustable Self Caliberating Multilocking , Revolving and Tilting Chair with Fixed Arms
of Make Fetherlite Amaze , Godrej , HNI or any Equivalent Brand as per Specification and
Colour as directed by the Architect. ( For Conference , meeting, Dias Chairs)
Each 62.00
4 Providing, supplying and installation of Executive High Back Imported Leather Chair with
Alumnium Buffed Arms And Base , Multilocking Mechanism of Make Fetherlite Crwon-1,
Godrej , HNI or any Equivalent Brand as per Specification and Colour as directed by the
Architect. ( For Director)
Each 1.00
5 Providing, supplying and installation of Leatherette Seat and Medium Back with,
Multilocking Mechanism and Two way adjustable arm, Chrome Base of Make FetherliteFP
Invention-2, Godrej , HNI or any Equivalent Brand as per Specification and Colour as
directed by the Architect. ( For Director's visitors)
Each 7.00
6 Providing, supplying and installation of High Back Chair With Headrest , Sliding and
Multilocking Mechanism and adjustable arm , Chrome Base of Make Fetherlite optima OC,
Godrej , HNI or any Equivalent Brand as per Specification and Colour as directed by the
Architect. ( For Asstt. Director)
Each 3.00
7 Providing, supplying and installation of Mesh Back Chair Synchro Mechanism and Two
adjustable arm , Nylon Base of Make Fetherlite ASTRO MB, Godrej , HNI or any
Equivalent Brand as per Specification and Colour as directed by the Architect. ( For Asstt.
Director Visitor's )
Each 9.00
BOQ FOR SUPPLY AND INSTALLATION OF CHAIR AND SOFASL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
PAGE 75 of 79
BOQ FOR SUPPLY AND INSTALLATION OF CHAIR AND SOFASL. NO. ITEM DESCRIPTION UNIT QTY Rate Amount
8 Providing, supplying and installation of Mesh Back Cushioned Seat Chair ,Synchro
Mechanism and Two adjustable arm , Nylon Base of Make Fetherlite ASTRO MB, Godrej
, HNI or any Equivalent Brand as per Specification and Colour as directed by the Architect.
( For Cubicle in Director's Office and Cabin in Large Incubation centre)
Each 2.00
9 Providing, supplying and installation of Designer Cafetaria Chairs of Make Fetherlite
Tango, Godrej , HNI or any Equivalent Brand as per Specification and Colour as directed
by the Architect. ( For Cafetaria
Each 0.00
10 Providing, supplying and installation of Designer Leatherette Sofa of Make Fetherlite S-
900-2S ( Converse) , Godrej , HNI or any Equivalent Brand as per Specification and
Colour as directed by the Architect. ( For Waiting area and Directors Room)
a. 3 Seater Each 15.00
b. 2 Seater Each 2.00
TOTAL
PAGE 76 of 79
1 Supply, Installation, Commissioning & Integration of
Network TDN IR Indoor Outdoor Bullet Camera 1 by 3
CMOS 1 3 MP 3 point 6 mm Fixed 24 IR LEDs PoE H264
Piece 21.00
2 Supply, Installation, Commissioning & Integration of
Network TDN IR Indoor Outdoor dome Camera 1by3 inch
CMOS 1point3 MP 2point8 mm Fixed 12 IR LEDs PoE
Hpoint264
Piece 85.00
3 Supply, Installation, Commissioning & Integration of
VIDEONETICS PRO IVMS - Master Server License
including media directory, archiving, recording Full blown
feature set, unlimited servers/unlimited sites/unlimited
clients support
OS 1.00
4 Supply, Installation, Commissioning & Integration of
Camera Connection License
License 106.00
5 Supply, Installation, Commissioning & Integration of 40"
Full HD LED Panel
Piece 4.00
Total
HD IP CCTV SURVEILLANCE SYSTEM
Sl. No. ITEM DESCRIPTION UNIT QTY Rate Amount
PAGE 77 of 79
1 Supply & Installation of CAT-6 IO BOX for Voice & Data Set 350.00
2 Supply & Installation of CAT-6 Patch cord (1 mtr length) Piece 300.00
3 Supply & Installation of CAT-6 Patch cord (3 mtr length) Piece 150.00
4 Supply & Installation of CAT 6 Patch panel (24 port) Piece 55.00
5 Supply & Installation of CAT 6 UTP cable ( 305Mtr) Drum 50.00
6 Supply & Installation of fully loaded 42U Server Rack Piece 1.00
7 Supply & Installation of fully loaded 24U Network Rack Piece 3.00
8 Supply & Installation of 15U Rack with full accessories Piece 12.00
9 Supply & Installation of L3 Network switch all port Giga 24
Port
Piece 1.00
10 Supply & Installation of L2 Network switch all port Giga 48
port
Piece 4.00
11 Supply & Installation of L2 Network switch all port Giga 24
port
Piece 8.00
Amount
BOQ FOR STRUCTURED CABLING
SL.
NO.
ITEM DESCRIPTION UNIT QTY Rate
PAGE 78 of 79
Amount
BOQ FOR STRUCTURED CABLING
SL.
NO.
ITEM DESCRIPTION UNIT QTY Rate
12 Supply & Installation of 8 Port managed Network switch Piece 10.00
13 Supply & Installation of 1” PVC Pile (Round & Square) meter 2,000.00
14 2900 series Router with 1 Port PRI , 64-channel high-density
voice and video DSP module , 1 Yr. Service & Warranty
Set 1.00
Total
PAGE 79 of 79