vj-426uf startup guide · [2] open the front cover slowly, holding it by the places shown in the...

VJ-426UF

Unpacking and Initial Setup

Startup Guide

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Connecting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . 8

Turning the Power On and Making the Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Setup via the control panel . . . . . . . . . . . . . . . . . . . . 13

Using the Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . 18

Test printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Accessing the Manuals . . . . . . . . . . . . . . . . . . . . . . . . 29

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

• Unauthorized copying or duplication of the whole or part of the contents of this Guide is prohibited.

• Every care has been taken in writing the contents of this Guide, but please contact MUTOH or the dealer you purchased the product from if you find any unclear, erroneous or otherwise unsatisfactory content in the Guide.

• Please be aware that MUTOH will not be liable in any way for failures or accidents that result from handling or operating the printer according to any procedures other than those set forth in this Guide.

• Company names and product names that appear in this Guide are registered trademarks of the respective companies.

2

1 Unpacking

• The operations of unpacking and moving this product must be carried out by four or more persons working together.

• Keep this product level when moving it.

Unpacking the printer

[1] Open the packing box and take out each part.

• The media height guide, wrapped in protective material, is stuck to the back of the printer.

Unpacking

CAUTION

Installation instruction:Startup Guide (this document)

Printer body

Accessory pack

Unpacking

In order to install the product and make the initial settings, you will need the following things in addition to the packaged items.

[2] Check if the followings are included.

Things to prepare in order to install and use the printer

Note

• Use a computer that runs one of the following operating systems:Windows 8/Windows 8.1, Windows 7, Windows Vista, Windows XP

• Be sure to use a power cable of the specified type. Using any other power cable could result in electric shock or fire. Contact the sales store for the specified power cable.

• Do not use a damaged power cable. It could cause electric shock or fire.

Software CD: 1Media height guide : 1 Lint-free cloths: 5

Cleaning sticks: 10

Installation instruction:Japanese/English(each)

Startup Guide(this document)

Gloves : 10Instruction sheet

for dedicated ink : 1

Printer: 1

Cross-headscrewdriver: 1Computer: 1

Power cable: 1

Ethernet cable: 1

Cleaning cartridges: 6Media: 1 Ink cartridges: 6

WARNING

Unpacking 3

4

Install this product in a place that:

• is level

• has no vibration

• has low humidity and little dust

• has no direct sunlight or strong lighting shining on it

• has small variation in temperature and humidity

• has no drafts (including those from heating or air conditioning equipment) blowing onto it

• has low levels of electromagnetic radiation and noise

Installation location

Minimum installation space

Ensuring a suitable place for installation

Install this printer within your reach on the table (including when opening the front cover).If you cannot easily open the front cover, adjust the printer position. If you are not in a balanced posture when you open or close the front cover, your hands or other body parts could get caught in it, possibly resulting in serious injury.

The place should be well ventilated when you do the installation work. If it is a poorly ventilated place, install a ventilating device. Otherwise, the odors from the inks could impact your health.

1388mm

1738.5mm150m

m

50mm

450mm

450mm

Size ofprinter body

Rear

Front

width×depth : 1188mm x 838.5mmheight : 544.6mm

Size of printer body

WARNING

CAUTION

Unpacking

Install the product in an environment that satisfies the conditions in the table below.

Installation environment conditions

Power supply

specifications

Voltage AC 100 V to 120 V ±10 % or 200 V to 240 V ±10 %

Frequency 50/60 Hz ±1 Hz

Capacity No less than 10 A

Environmental

conditions

Operating environment Temperature 20 to 32 °C, humidity 40 to 60 %,no condensation.

Ranges to ensure printingprecision

Temperature 22 to 30 °C, humidity 40 to 60 %, no condensation.

Environment for storage • If not charged with ink when stored: up to 6 monthsTemperature -20 to +60 °C, humidity 20 to 80 %.

• If charged with ink when stored: up to 1 week* Temperature -10 to +40 °C, humidity 20 to 80 %. *Up to 4 days if the ambient temperature is 32 °C or higher.

Cautions in using this product

When opening and closing the front cover

Do not open or close the front cover if you are not in a balanced posture. If you open or close it in an unbalanced posture, your hands or other body parts could get caught in it, possibly resulting in serious injury.

• Always close the front cover fully.If you leave it part-open, it could close suddenly.

• When closing the front cover, always use both hands and hold it by the portions specified. Do not place your fingers on the edges of the printer's opening portion, or on any parts around those edges.

Your fingers could get caught and be injured.

Always hold the cover by the places shown in the picture, using both hands, and close it slowly.

WARNING

CAUTION

Unpacking 5

6

You will need a cross-head screwdriver for this procedure, so have one ready. A store-bought item will do.

Removing the protective materials


Steps

[1] Remove all the protective materials and tapes that are stuck onto the outside of the product.

[2] Open the front cover slowly, holding it by the places shown in the picture and using both hands.

• Open the front cover fully up as far as it will go.

Always open the front cover fully.If you leave it part-open, it could close suddenly.

[3] Remove the protective sheet from the UV-LED lamp.

[4] Remove the screws, and remove the head fixing plate.

• Slide the head fixing plate leftward to take it out.

Note

Remove the head fixing plate carefully, so that it does not scratch any of the surrounding parts.If they are scratched, the print quality could drop.

WARNING

CAUTION

× 1

Unpacking

[5] Remove the protective material for the Steel Bare.

[6] Remove the two screws from the printer rear side.

[7] • Remove the protective material from the table.

• Peel all the tapes off.

• Also remove the protective sheet from the inner part of the table.

[8] Remove the eight screws, and remove the two table fixing plates.

[9] Close the front cover slowly, holding it by the places shown in the picture and using both hands.

When closing the front cover, always use both hands and hold it by the portions specified.Do not place your fingers on the edges of the printer's opening portion, or on any parts around those edges. Your fingers could get caught and be injured.

Important!

Keep the head fixing plate, table fixing plates and screws, because they will be reused if the product is transported.

× 2

× 8

CAUTION

Unpacking 7

8

2 Connecting the Cables

Connecting power and Ethernet cables

1. Before connecting the cables...

• Close the front cover.

• Check if the waste ink clip is locked.

2. Connecting the power cable

[1] Make sure that the power button is turned off.

Note

• If the power switch is in a pressed-inward state, it is turned on and you must press it again to turn it off.

[2] Connect the power cable to the product.

[3] Insert the power cable’s plug into the outlet. Be sure to insert it correctly.

Connecting the Cables

1 2 3 4 5 6

Option

1 Media Set

Check!

Connecting the Cables

3. Connecting the Ethernet cable

[1] Connect the Ethernet cable to the product.

[2] Connect the Ethernet cable to the computer.

Important!

• The left figure is the example of peer-to-peer connection between this product and computer. Connection method differs depending on the usage environment.

• If you use the product with a LAN, connect the cable so that the computer and printer are on the same subnet.

Connecting the Cables 9

10

2 Turning the Power On and Making the Initial Settings

When you turn the power on for the first time, make the initial settings according to the instructions displayed.

Turn on the power

[1] Turn on the printer’s Power button.

• The blue indicator will light up.

• The printer will start to power up.

Important!

Check before turning the power ON.

• Is the front cover closed?

Making the initial settings

1. Setting the language and length unit, etc.

[1] Press the [-] key to select “Lang: English”.

Press the [Enter] key.

[2] Press the [Enter] key.


Turning the Power On and Making the Initial Settings

1 2 3 4 5 6

Option

1 Media Set

Press!

Lang： English

Length : mm

Remain Ink : On


2. Setting the IP address, etc.

[1] Sets the IP address of the printer.

• Use the [+] key to increase a setting value.

• Use the [ - ] key to decrease a setting value.

• Press the [Enter] key to confirm. The cursor will move on to the next.

• Confirm your input for each value.

Note

• Set an IP address that is different from the IP address of the computer that the printer

will be connected to.

• Be sure to set the IP address after consulting the network administrator.

• The IP address can alternatively be set later using Panel setup menu and ValueJet

Finder.

[2] Sets the subnet mask of the printer.





Note

• If the printer is to be connected peer-to-peer to a computer, you can leave the

settings at the default values.

• Be sure to set the subnet mask after consulting the network administrator.

[3] Sets the gateway.





Note

• If the printer is to be connected peer-to-peer to a computer, you can leave the

settings at the default values.

• Be sure to set the gateway after consulting the network administrator.

The printer starts initialization operations.

• That completes the initial settings.

IP: 192. 168. 1. 253

MASK: 255. 255. 255. 0

GW: 1 9 2. 1 6 8. 1. 2 5 4

Initializing

Turning the Power On and Making the Initial Settings 11

12

With the initial settings completed, there are two ways to do the remainder of the setup procedure. Choose the way that you like.

• Doing the setup via the control panel, following the instructions in this Guide "Setup via the control panel" P.13 below

• Doing the setup via the computer, following the instructions in the Setup Wizard "Using the Setup Wizard" P.18 below

Selecting how to do the remaining setup procedure


2 Setup via the control panel

This printer requires activation when the power is turned ON for the first time.

Step 1 Carrying out activation

When the message on the left appears, carry out activation. There are two ways of carrying out activation.

"To activate via the control panel:" P.13 below "To activate via the internet:" P.13 below

To activate via the control panel:

[1] Press the [Enter] key when the message on the left appears.

[2] Enter a 16-digit activation code.





Note

Obtain the activation code from the distributor, by email or other means.

[3] • When the message on the left appears, turn the power button off.

• Wait a short while, then turn the power button on, to restart the printer.

To activate via the internet:

When the message on the left appears, carry out activation according to the “Printer Activation Guide”.

Note

You can obtain the “Printer Activation Guide” by accessing the ValueJet Club via the

internet address below and registering as a user under “Register”.

https://valuejetclub.mutoh.co.jp/mutoh/guser/

Setup via the control panel

Activation required

Activation required

0 0 0 0 - 0 0 0 0 - 0 0 0 0 - 0 0 0 0

Reboot a printer

Activation required

Setup via the control panel 13

14

Step 2 Initial charging of ink

1. Initial cleaning

[1] Press the [Enter] key when the message on the left appears.

[2] When the message on the left appears, make sure the waste ink tank is empty, and press the [Enter] key.

Note

You can see whether the tank is empty by looking through the eyehole.

The message on the left will appear.

[3] Insert cleaning cartridges into all the cartridge slots.

• The arrow should face up.

• Insert all the way to the end.


• Start charging cleaning fluid.

When cleaning fluid charging ends, the message on the left will appear.

[4] Remove all cleaning cartridges.


• Cleaning fluid starts to be discharged.

Start Ink Charge ->E

Empty WasteInk ->E

Insert CleaningCart.

Busy-Washing **%

Remove Cartridges

Busy-Washing **%


[5] If the message on the left appears, get a PET bottle or other container ready, to transfer the waste ink into.

Important!

The capacity of waste ink tank is 1500 ml. Make sure to prepare a container

that has enough capacity when discharging waste ink.

[6] Pull out the tip of the waste ink tube.

[7] • Insert the waste ink tube into a container.

• Release the tube clip of waste ink.

• Pour waste ink into the container.

• When you have finished transferring the waste ink, lock the waste ink tube clip.

• You are obligated to properly dispose of waste fluid from the printer in compliance with Wastes Disposal and Public Cleansing Act and local ordinances. Delegate disposal to an industrial waste disposal contractor.

• Waste fluid from this product is harmful to aquatic organisms. Avoid the waste fluid from out flowing to sewage or natural water systems.

[8] • Press the [Enter] key.

• The message on the left will appear.

Empty WasteInk ->E

WARNING

Insert InkCartridges


16

2. Ink charging

[1] Shake new ink cartridges horizontally 10 times.

[2] Insert ink cartridge to this product.

• Match the label of this product to the color of ink cartridge.

• The arrow should face up.

• Insert all the way to the end.


• The printer starts ink charging.

When ink charging ends, the message on the left will appear.

Ink Charge **%

Set media, then

press Set Media key.


The accessory CD contains the software and data listed below.

Step 3 Installation of the software

ValueJet Finder (VJ Finder) Sets an IP address for the printer, so that it can communicate with the computer.

Printer driver Needed for sending data from the computer to the printer. Also used for changing the print settings and at certain other times.

ValueJet Status Monitor (VSM) Monitors the printer’s status information, and is able to alter various settings. Also able to carry out initial ink charging and test printing.

ValueJet Layer Editor This enhances the printer driver's layer printing capability.

Manuals (for printer and software) See "Accessing the Manuals" P.29 for how to access the manuals.The following manuals are available. They are in pdf format.

• VJ-426UF Operation manual “Operations and Maintenance Methods”

• VJ-426UF Driver User’s Guide

• ValueJet LayerEditor Operation manual

• ValueJet Status Monitor Operation manual

• ValueJet Status Monitor Installation wizard Operation manual

• VJ-426UF Startup Guide (This manual)

[1] Insert the accessory CD into the computer's CD-ROM drive.

Note

• The Set-up Wizard will start up automatically.

• If the set-up wizard does not automatically start, right click the icon of CD-

ROM drive, open the contents of CD with [Open], and double click

VjTotalInst.exe.

[2] Carry out software installation by following the instructions on the Set-up Wizard screen.

• When installation is complete, carry out test printing. "Test printing" P.20

• When you have finished, do NOT turn the power off. Instead, use the sleep mode. "Sleep Mode" P.28


18

2 Using the Setup Wizard

The accessory software CD has the following functions.

• It displays the procedure for setting up the printer, on the computer screen (Set-up Wizard function).

• It installs the following software and data to the computer (combined installation function).(The manuals will not be installed by the integrated installer function.)

Insert the software CD

ValueJet Finder (VJ Finder) Sets an IP address for the printer, so that it can communicate with the computer.

Printer driver Needed for sending data from the computer to the printer. Also used for changing the print settings and at certain other times.

ValueJet Status Monitor (VSM) Monitors the printer’s status information, and is able to alter various settings. Also able to carry out initial ink charging and test printing.

ValueJet Layer Editor This enhances the printer driver's layer printing capability.

Manuals (for printer and software) See "Accessing the Manuals" P.29 for how to access the manuals.The following manuals are available. They are in pdf format.

• VJ-426UF Operation manual “Operations and Maintenance Methods”

• VJ-426UF Driver User's Guide

• ValueJet LayerEditor Operation manual

• ValueJet Status Monitor Operation manual

• ValueJet Status Monitor Installation wizard Operation manual

• VJ-426UF Startup Guide (This manual)

[1] Insert the accessory CD into the computer’s CD-ROM drive.

Note


• If the set-up wizard does not automatically start, right click the icon of CD-

ROM drive, open the contents of CD with [Open], and double click

VjTotalInst.exe.

[2] Carry out set-up by following the instructions on the Set-up Wizard screen.

• When setup is complete, carry out test printing. "Test printing" P.20

• When you have finished, do NOT turn the power off. Instead, use the sleep mode. "Sleep Mode" P.28

Using the Setup Wizard

Using the Setup Wizard

Flow of setup using the Setup Wizard

Initial settings for software

Initial ink charge

Installation of software

Set-up is now complete!

Install to the computer the software that will be used with the printer.

Have an IP address set for the printer, and have the VSM initial settings and so forth implemented.

Install the ink cartridges and carry out charging with ink.

Using the Setup Wizard 19

20

2 Test printing

Get an A4 size media ready, for carrying out the nozzle check.

Setting up media


1. Placing the media on the table

[1] Check that the message on the left is displayed.If it is not, press the [Remove Media] key.

[2] Open the front cover slowly, holding it by the places shown in the picture and using both hands.

• Open the front cover fully up as far as it will go.

Always close the front cover fully.If you leave it part-open, it could close suddenly.

Note

• If the message on the left is displayed, you can use the [+] and [ - ] keys to alter the

adsorption fan’s intensity.

• Use this when you want to alter the adsorption fan’s intensity according to the

media's thickness.

• The adsorption fan will start operating when the [+] or [ -] key is pressed.

• If you alter the setting, it will be reflected in the currently selected User Type.

Place the media on the table.

Test printing

WARNING

Set media, then

press Set Media key.

CAUTION

Cover Open + -

Test printing

[3] Place the media on the table.

• Set an A4 size media sideways on the table.

2. Adjusting the table's height

[1] Open the PG handwheel cover, by pressing on it.

[2] • Turn the PG handwheel to lower the table.

• Position the media height guide over the table.

[3] Turn the PG handwheel to raise the table to the position where the media touches the media height guide.

Test printing 21

22

[4] • Remove the media height guide.

• Close the PG handwheel cover.

[5] Close the front cover slowly, holding it by the places shown in the picture and using both hands.

When closing the front cover, always use both hands and hold it by the portions specified. Do not place your fingers on the edges of the printer's opening portion, or on any parts around those edges. Your fingers could get caught and be injured.

[6] • Press the [Set Media] key.

• The message on the left will appear. The table will move inward, and a check will be run using the obstacle sensor, to make sure that the media will not contact with the head.

Note

If the table is still positioned too high, the following will appear in the order given:

“Obstacle Detected”, “Press Remove Media”, “key”. Press the [Remove Media] key and

readjust the table’s height.

CAUTION

Wait for a While

Test printing


Important!

• This menu item only appears when the User Type are selected for the first time.

• If you select “On”, you will have to input the media width, media height, media set

position and origin position after pressing the [Set Media] key each time you set a

media on the table.

• If you select “Off” via the [ - ] key, “Ready to Print” will be displayed after pressing the

[Set Media] key each time you set a media on the table. In that case, the currently

selected User Type values will be used for the media width, media height, media set

position and origin position.

3. Inputting the media width and length

[1] Use the [+] / [ - ] key to input the media width.


Note

• These menu items will only appear if “On” is set for “Detailed-Set”.

• Any value from 30 mm to 483 mm can be set for the width.

• If media with width 483 mm is used, it will not be possible to input a Y-direction value

for the set position.

[2] Use the [+] / [ - ] key to input the media length.


Note

• Any value from 30 mm to 329 mm can be set for the length.

• If media with length 329 mm is used, it will not be possible to input an X-direction

value for the set position.

Detailed-Set : On

Width : 483mm

Length : 329 mm

Test printing 23

24

4. Inputting the set position


Note

• This menu item will only appear if “On” is set for “Detailed-set”.

• If you know the media set position in advance, you can input it here, using the

[+] / [ - ] key to enter the X (longitudinal) value and [<] / [>] key to enter the Y (lateral)

value.

• For the set position, any value from 0.0 to 265.0 can be set for the X value, and any

value from 0.0 to 453.0 for the Y value.

*These ranges will vary depending on the values set for the media width and length.

• The table will move inward.

• The carriage will move to the set position, with its LED pointer lit steady.

[2] • Use the keys to align the LED pointer right foreground of the media.

• Use the [+] / [ - ] key to move the table forward/backward (longitudinally).

• Use the [<] / [>] key to move the LED pointer leftward/rightward (laterally).

Press the [Enter] key to set the position.

SET X : 0.0 Y : 0.0

Moving Location Pos.

Y X0.0

SET X : 10.0 Y : 20.0

Test printing

5. Inputting the origin position


Note

• This menu item will only appear if “On” is set for “Detailed-set”.

• If you select “Off” for this, the origin position set in the User Type will be X = 5.0,

Y = 5.0.


Note

• If you know the media origin position in advance, you can input it here, using the

[+] / [ - ] key to enter the X (longitudinal) value and [<] / [>] key to enter the Y (lateral)

value.

• For the origin position, any value from 5.0 to 270.0 for the X value, and any value from

5.0 to 453.0 for the Y value, can be entered.

*These ranges will vary depending on the values set for the media width and length.

• The table will move inward.

• The carriage will move to the set position, with its LED pointer lit steady.

[3] Use the keys to move the LED pointer to the origin position (print start point).

• Use the [+] / [ - ] key to move the table forward/backward (longitudinally).

• Use the [<] / [>] key to move the LED pointer leftward/rightward (laterally).

Press the [Enter] key to set the position.

That completes setting of the media.

Note

• Pressing and holding down the [Enter] key for 2 seconds or longer while “Ready to

Print” is displayed will bring up an inputting menu for the media width, length, set

position and origin position.

• Any values you input will be reflected in the currently selected User Type.

Origin : On

ORG X : 5.0 Y : 5.0

Moving Origin Pos.

Y X0.0

ORG X : 15.0 Y : 40.0

Ready to Print

Test printing 25

26

Run the nozzle check printing, and if there is nozzle clogging, carry out cleaning.

This printer has the following 2 kinds of nozzle checks:

• Nozzle Check - Prints the nozzle check patterns

• Nozzle Check B - checks the nozzle for white ink. Prints the nozzle check patterns on a colored background, to make it easy to see the white ink nozzle's status.

Nozzle check and cleaning

Note

“Nozzle Check B” will only appear in the menu if 6-color is set.

1. Nozzle check steps

[1] Set the media to be used for the nozzle check on the table, and carry out the procedure as far as setting the origin position.

• Set an A4 size media sideways on the table.

[2] Press the [Menu] key

[3] • Press the [ - ] key several times, to bring up the display on the left.

• Press the [>] key.

[4] • Press the [Enter] key.

• To select Nozzle Check B, press the [ - ] key to display “Nozzle Check B”, then press the [Enter] key.

• Nozzle check patterns will be printed.

[5] Check the patterns.

• If there is nozzle clog, go to "Cleaning steps" P.27.

• If there is none, go to "Sleep Mode" P.28.

With Nozzle Check B, the patterns will look like the pictures on the left.

Note

For the nozzles other than white ink, the background will be white.

1

2

Set Media

Media Set

Low speedPress!

Menu2: Test Print>

Test2: Nozzle Check B

Test1: Nozzle Check

No nozzle clog Nozzle clogged

No nozzle clog Nozzle clogged

Test printing

2. Cleaning steps

[1] Press the [Cleaning] key, so that the “Normal” indicator (one of the “Cleaning Mode” indicators) lights steady.

• The cleaning mode will be set to “Normal”.

Note

You can alternatively do this via the printer driver or the VSM’s remote panel.

[2] Give the [Cleaning] key a long press, for 2 seconds or more.

• Cleaning will start.

[3] Conduct a nozzle check, again. "Nozzle check steps" P.26

• If there is still nozzle clogging, repeat normal cleaning. See “Head cleaning" P. 77 of the operation manual regarding “Short”, “Long” and “LittleCharge” cleaning.

Option

1

2

Set Media

Media Set

Low speedPress!

Normal Cleaning

Option

1

2

Set Media

Media Set

Low speedPress!

Test printing 27

28

2 Sleep Mode

When you are not using the printer, always leave the power on and put the printer into the sleep mode. If you do not put the

printer into the sleep mode, the ink in its interior could settle out and/or coagulate, causing poor image quality or printer failure.

If you set the printer's sleep mode, the printer performs the following operation.

• Automatic Head cleaning is performed after the time set in the Timer Setting Menu has elapsed.

• Some of the ink inside the printer is circulated (every hour).

• Refills a small amount of ink (once a week).

Important!

• If you are using 6-color set model, do not leave the printer in Sleep mode for more than seven days. If the printer is going to be in Sleep mode for more

than seven days, perform “Storing for a long time” P.97 on operation manual, and then turn the power OFF.

• If you are using 4-color set model and the printer is going to be in Sleep mode for more than one week, shake the ink cartridges once one week has passed.

[1] Make sure that the printer’s operating condition is as follows:

• Printing or other operation is not in progress.

• Front cover is closed.

• There is ample amount of ink in the ink cartridges.

• There is enough free space in the waste fluid bottle.

Important!

• If you are going to use the sleep mode for a prolonged period of time, first empty out the waste ink from the waste ink tank, as follows.

[2] Press the [Menu] key.

[3] • Press the [ - ] key several times, to bring up the display on the left.

• Press the [>] key.


• The sleep mode will start.

• To exit the sleep mode, press the [Enter] key.

Note

• To set the sleep mode to come on by the timer, see “SleepMode 2: SetTmer” P. 68 on the Operation manual.

• The printer may automatically execute head cleaning and/or ink charging, etc., when it exits the sleep mode. Such operation will depend on the time that

has elapsed since the last time. Such operation does not depend on the sleep mode settings. It is an automatic maintenance function of the printer.

Sleep Mode

1

2

Set Media

Media Set

Low speedPress!

Menu5: Sleep Mode>

SleepMode 1 : Start

Restart -> Enter

Sleep Mode

2 Accessing the Manuals

Follow the procedure below to access the manuals in the accessory CD.

[1] Insert the accessory CD into the computer's CD-ROM drive.


• If it does not start up automatically, go to step [3].

[2] To exit the Startup Wizard, click the “X” in the top right corner of its screen.

[3] For Windows 8 / Windows 8.1 users:

• On the [Start] screen, click [Desktop].

• Click [Explorer].

• Double-click [PC] or [Computer]

For Windows 7 / Windows Vista / Windows XP users:

• Click [Computer] or [My Computer] in the [Start] menu.

[4] Right-click the CD-ROM drive icon, and select [Open].

[5] Open the [Manual] folder.

[6] • Open the applicable folder.

• Double-click on a pdf.

Accessing the Manuals

Accessing the Manuals 29

30

3 Safety Instructions

For Users in Europe

For Users in the United States

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Signification of WARNINGs and CAUTIONs

Meaning of symbols

Important Notice

The CE marking is a mandatory European marking for certain product groups to indicate conformity with the essential health and safety requirements set out in European Directives.

By affixing the CE marking, the manufacturer, his authorized representative, or the person placing the product on the market or putting it into service ensures that the item meets all the essential requirements of all applicable EU directives and that the applicable conformity assessment procedures have been applied.

About the safety notices

Used for dangerous situations where death or serious injury may be caused.

Used for dangerous situations that may cause slight or medium injury, or when all or parts of products are damaged.

Warning symbol Meaning

Indicates “prohibited” operations.

Indicates required operations.

Note

• Refer to “Introduction” P.8 of operation manual for names of each component in the main body.

Safety Instructions

WARNING

CAUTION

Safety Instructions

Concerning electric shock, short circuits and fire

Do not install the printer where it is humid or dusty.It could lead to an electric shock and fire.

Make sure to use only the specified power supply.If a power supply other than the specified voltage is used, it could cause an electric shock and fire.

Do not use a damaged power cable.It could lead to an electric shock and fire.

Take power for the printer directly from the power socket.Do not use multiple plugs on the same socket.This could generate heat and might cause fire.

Do not pull out or insert the power plug with a wet hand.This could lead to an electric shock.

Be sure to use a dedicated power socket with earth wire for the power supply, and connect it to the earth wire.If the earth wire is not connected, an electric shock or fire may occur.

Do not connect an earth wire to the following places.

• Gas pipe There is a possibility of ignition and explosion.

• Earth wire of telephone cables and lightning rods Heavy current might flow whenever lightning strikes.

• Water pipe and faucet The earth might not work if a plastic pipe is connected

in the middle of the metal pipe.

Connect up the cords (cables) in the ways specified in this Guide. Mistakes in the cable connections could result in fire.

Do not insert or drop metal or flammable objects into the printer through openings such as a vent.It could lead to an electric shock or fire.

Be sure to use the specified power cord set.

• Using a power cord set other than the specified can cause an electric shock or fire.

• Use a power cable that is equipped with a protective grounding terminal, and connect it firmly to the outlet.

• Use a power cable that conforms to the safety regulations, power supply voltage and plug shape of the country where you are using it.

If foreign substances or liquids such as water entered the printer, do not use the printer as it is.It could lead to an electric shock or fire.Turn the power button OFF immediately and disconnect the power plug from outlet. Then contact the customer support.

Do not place any combustible materials on the platen while the heater is working.There may be a risk of fire.

Leave ink cartridge from fire or objects with high temperature.It can cause fire.

Pay attention to the following points when handling the power cord set.

• Do not tamper with the power cord set.

• Do not put heavy objects on the power cord set.

• Do not bend, twist or pull the power cord set by force.

• Do not route the power cord set near heating appliances.

Never open covers attached using screws under any circumstances.This may cause an electric shock or a malfunction.

Make sure to connect an earth wire to the earth connection that meets the following standards.

• Earth terminal of power socketAn earth wire with a copper plate which is buried at 650 mm or more in the ground.

• Pay attention to the following points when handling the power plug.Any mishandling of the power cable could cause a fire.

• Make sure that no foreign substances such as dust are stuck to the power plug.

• Make sure that the power plug is firmly inserted to the edge of the power socket.

When you do not use the printer for a long period, make sure to pull out the power plug from the power socket for safety.

Make sure that no moisture enters the printer.It could cause shorting of the electrical circuits.

WARNING

Safety Instructions 31

32

Installing the printer

Do not install the printer on a surface: On such surfaces the printer could topple over or fall off, potentially causing injury.

• that is shaky, or

• that is tilted, or

• that receives vibration from other machines or equipment nearby.

Do not slant the printer, turn it upside down.The ink inside the printer may leak.Moreover, normal operation after shifting (to these positions) cannot be guaranteed.

Keep this product level when moving it.

The operations of unpacking and moving this product must be carried out by four or more persons working together.

Concerning handling

Do not step on this printer or place heavy things on top of it.It may cause an injury if the printer falls down.

Observe the following instructions for handling of the front cover.

• The front cover must not be opened or closed by children.Their hands, head or other body parts could get caught

in the cover, possibly resulting in serious injury.

• Do not install the printer in a place where a strong airstream from a fan, air conditioner or similar will blow on the front cover.It could be blown closed suddenly.

• Make thoroughly sure that the surrounding area is safe before opening the front cover.Otherwise it might strike an object or person.

Heed the following instructions for cleaning of the cleaning wipers and the print head outer periphery.

• Wear goggles and/or other protective equipment, so that ink will not get in your eyes.

• Wear gloves, so that ink will not get directly on your hands.

• Do not use the same cleaning stick more than once. The dirt on a used cleaning stick could result in damage

to the print head.

Heed the following when cleaning the print head outer periphery.

• NEVER touch the surfaces of the print head’s nozzles.It could result in damage to the print head.

• Do not touch the tip of a cleaning stick.You could get oil or grease on it, which could result in

damage to the print head.

• Never allow any water to get onto the tip of a cleaning stick.It could result in damage to the print head.

WARNING

CAUTION

WARNING

CAUTION

Safety Instructions

Concerning handling (continued)

Heed the following when cleaning the cleaning wipers.

• Do not touch the cleaning wipers or the head cap unit.You could get oil or grease on them, with the result that

head cleaning cannot be implemented normally.

• To wipe the cleaning wipers, use only the cleaning sticks, and use them in a dry state.Using the cleaning sticks wetted with water or other

liquid will cause clogging of the print head.

When moving this product, always empty the waste ink tank even if it is for a short distance.If ink splashes inside the waste ink tank while being moved, it can cause damage.

Do not use volatile solvents such as thinner, benzene, or alcohol.These solvents may cause damage to the paint.

The bluish white light that comes from the UV LED equipment is ultraviolet light.Ultraviolet light may leak a little from the gaps of the equipment. The level of this ultraviolet light that leaks from the equipment is minimized, but be alert of the following points when handling this product.

• Do not look at the ultraviolet light at close range for a long period of time.This may cause eye damage.

• Do not shine the ultraviolet light on your skin at close range for a long period of time. This may cause skin inflammation.

Keep the work area well-ventilated. If the ventilation is poor, install a ventilating device. Otherwise, the odors from the inks could adversely impact your health.

Observe the following cautions when opening or closing the front cover.

• When closing the front cover, lower it slowly down so that your hands or other body parts do not get caught.

• If you hold it by the other edges of the printer's opening portion, or by parts around those edges, your hands could get caught and be injured.

• When opening or closing the front cover, hold it by the portion specified, so that your fingers do not get caught.If you hold it by applying your fingers to any other

portion, they could get caught and seriously injured.

• Always open the front cover fully.If you leave it part-open, it could close suddenly.

Concerning consumable items

• You are obligated to properly dispose of waste fluid from the printer in compliance with Wastes Disposal and Public Cleansing Act and local ordinances. Delegate disposal to an industrial waste disposal contractor.

• Waste fluid from this product is harmful to aquatic organisms. Avoid the waste fluid from out flowing to sewage or natural water systems.

WARNING


34

There are warning labels pasted in dangerous places in this product. The contents of label are as described next and always follow them. If the labels are peeled off or become dirty, contact the sales store for exchange.

Concerning consumable items(continued)

• Uncured UV-curable ink is harmful to skin, so always wear gloves when handling the ink cartridges, so that the ink will not get onto your hands.

• If the ink gets onto your skin, immediately wash it off with soap and large amounts of water, and consult a physician if anything feels abnormal.

• If the ink gets into your eye, flush it with large amounts of water and promptly have it examined by a physician.

• Wear goggles and protective clothing as necessary.

Regarding the ink cartridges, be sure to:

• Shake the cartridges daily.

• Shake the cartridges before working with the printer.

Do not disassemble Ink cartridges.If disassembled, there is a possibility that ink might come into contact with your eyes or skin.

Before operation, make sure to read the Material Safety Data Sheet (SDS).

During ink charging, abide by the following.

• Do not turn off the printer’s power.

• Do not disconnect the printer’s power cable.

• Do not open the front cover.

• Do not raise the paper setting lever.

Warning labels

Do Not Touch Label :Do not touch the indicated area when opening and closing the front cover.

UV caution label :CAUTION ULTRAVIOLET LIGHT: Do not look directly at light or let it shine on your skin for long period of time.

Laser warning label

Keep Hands Clear Label :Do not get your fingers caught when closing the front cover.

CAUTION

Safety Instructions

Operation instruction labels are stuck on the printer at places where caution in operation is required. The contents of these labels are as shown below.

Concerning operation instruction labels

Ink color indicating labels

Install ink cartridges that match the colors in the labels.

Moving Printer Label


VJ426UFE-Q-00

vj-426uf startup guide · [2] open the front cover slowly, holding it by the places shown in the...

Documents