vii sem report format

8/4/2019 VII Sem Report Format

1/8

A

Seminar Report

On

PRACTICAL TRAINING

ACADEMIC SESSION 2007-08

FOR THE PARTIAL FULFILLMENT OF THE BACHLORS DEGREE COURSE IN

ELECTRONICS AND COMMUNICATION ENGINEERING

TAKEN AT

(LOGO OF THE COMPANY)

(COMPANY NAME)(PLACE)

ELECTRONICS & COMMUNICATION DEPARTMENT

KAUTILYA INSTITUTE of TECHNOLOGY& ENGINEERING

UNIVERSITY of RAJASTHAN

Month-11

Submitted to:Name of faculty

designation

KITE, Jaipur

Submitted By:Name of the Person

(roll no.)


2/8

CERTIFICATE(font 14-Bold)

This is to certify that the report titled same as on the coverpage that is being submitted by name of the candidate is in partial

fulfillment of the requirements for the award of BACHELOR OF

ENGINEERING DEGREE, is a record of bonafide work done under

my /our guidance. The contents of this thesis, in full or in parts, have

neither been taken from any other source nor have been submitted to any

other Institute or University for award of any degree or diploma and the

same is certified.

Name of

SEMINAR COORDINATOR


3/8

ACKNOWLEDGEMENTS (font 14-Bold)

It is customary to acknowledge the College Management / respective

Dept. Head for giving the candidate an opportunity to carry out his /her

studies at the University.

The Student is free to acknowledge all those he feels he should

acknowledge on the basis of the guidance and help provided during the

implementation of the Training. Appropriate acknowledgement should be

given to all concerned.

(To be signed by the student)

Reg. No. XXXXXXX


4/8

ABSTRACT (14-bold)

The abstract should be well written, clearly defining the objective of thework that was to be carried out. It should precisely indicate the original

Thesis goals that were defined and if the same have been achieved. If the

same were achieved the results of the work must be highlighted. If the

same were not achieved, the reasons for the same must be briefly

explained and it should be explained as to what mid-course corrections

were introduced and what was achieved.


5/8

TABLE OF CONTENTS (font 14 bold)

LIST OF TABLES (if any) v to ----

LIST OF FIGURES ---- to ----LIST OF ABBREVIATIONS -----to ----

NOTATION -----to ----

CHAPTER 1 Introduction Page

Nos

1.1 Objective and goal of the Report 1

1.2 Detailed literature survey

1.3

1.3.1

1.3.21.4

And so on

CHAPTER 2

This chapter normally should give the essential back-ground

Theory on the subject of the project and essential derivations

or the like.

(Above number pattern should be followed for Sections and sub-

sections.)

CHAPTER 3

This chapter should normally cover design / programming

methodologies or other approaches suggested in the Training.


sections.)

CHAPTER 4

Detailed approach followed for the implementation of the

project.

(a) In case Hardware or Experimental Projectsdetailedexperimental approach followed, measurement setups, process

steps, experimental setup etc.


6/8

(b) In case of simulation, modeling, programming

techniques, the programming steps, flow charts,

simulation results, verification of the approach

followed.

And the like depending on the nature of the project.


sections.)

CHAPTER 5

Analysis of the results - may contain plots, simulated results,synthesis of process,

Interpretation of the results. Comparison of the results with

the published

data and deviations /improvements, if any.


sections.)

CHAPTER 6

CONCLUSION


sections.)

REFERENCES:

(Comprehensive list of references must be given. All these references

must be linked to the text of the report as reference no (5) must beshown superscript [5] or [5] or as [5] along with the text.

Brief Bio-data of the Candidate:

(Last page/s)


7/8

CHAPTER 1INTRODUCTION (Title 14-Bold Capital letters)

paragraph font 12- times new roman with 1.5 line spacing

with justify paragraph.

Put a header: topic of your training and organization name.

Put footer: Dept. of Electronics & Communication, KITE,Jaipur. And page number.

The main contents in the Dissertation/ Thesis should be typed in Times

New Roman 12 font and page no. should be numbered from Abstract

as 1, 2, 3 Spacing between consecutive lines should be 1.5.

Separate successive paragraphs by 9 points. Margins of each page

should be preferably 1.25 inch left side, 0.75 inch right hand side,one inch top and 1.5 inch bottom with page no. at bottom margin of

one inch. For each chapter at top right corner chapter no. should be

written: for example; for chapter 1, it should be Chapter - 1 (Font 12,

Times New Roman). Title of the chapter should be typed in Font 14

(All Capital) and should be centered. Literature references will be

arranged in the order in which they are referred in the Thesis.

Reference no. will be put in square brackets within the text in the

order in which they are cited. Preferably, the report should be

organized as under:

i) Contents (Pg no. should be numbered in Roman as i, ii, iii distinctto that of starting from Abstract).

ii) Abstract

iii) Introduction (Chapter - 1, Essential, Detailing Scope of work

with Objectives)

iv) Literature survey (Chapter - 2, Essential)

v) Chapters describing the Work (Tables should be given the number

based on their chapters; for example; for chapter 2 they should be

Table 2.1, 2.2 and so on.


8/8

vii sem report format

Documents