SECTION 08554ALUMINUM-CLAD WOOD WINDOWS AND PATIO DOORS

JELD-WEN Custom Series

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Wood Windows and Patio Doors: (Custom Series)1. Awning windows.2. Casement windows.3. Double-hung windows.4. Horizontal sliding windows.5. Radius and geometric windows.

a. Direct-Setb. In-Sash

6. In-swing patio doors.7. Out-swing patio doors.8. Sliding patio doors.

1.2 REFERENCES

A. Window and Door Manufacturers Association (WDMA):1. AAMA/WDMA/CSA 101/I.S.2/A440 North American Fenestration Standard /

Specification for windows, doors, and skylights (NAFS)

B. ASTM International (ASTM):1. ASTM E 1886 - Standard Test Method for Performance of Exterior Windows, Curtain

Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials.

2. ASTM E 1996 - Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes.

C. National Fenestration Rating Council (NFRC):1. NFRC 100 - Procedure for Determining Fenestration Thermal Properties.2. NFRC 200 - Solar Heat Gain Coefficient and Visible Transmittance.

D. Window and Door Manufacturers Association (WDMA): WDMA I.S.4; Water Repellent Preservative Non-Pressure treatment for Millwork

1.3 SUBMITTALS

A. Submit under provisions of Section 01300.

B. Product Data: Manufacturer's data sheets on each product to be used, including:1. Preparation instructions and recommendations.2. Storage and handling requirements and recommendations.

08554-1

3. Installation methods.

C. Shop Drawings: Submit shop drawings indicating details of construction, flashings and relationship with adjacent construction.

D. Selection Samples: For each factory-finished product specified, two complete sets of color chips representing manufacturer's full range of available finishes.

E. Verification Samples: For each factory-finished product specified, two samples, minimum size 6 inches (150 mm) square, representing actual finishes.

F. Quality Assurance Submittals:1. Design Data, Test Reports: Provide manufacturer test reports indicating product

compliance with indicated requirements.2. WDMA Hallmark certification.

G. Closeout Submittals: Refer to Section 01700 Closeout Submittals.

1.4 QUALITY ASSURANCE

A. Installer Qualifications: Minimum 2 years installing similar assemblies.

B. Certifications: WDMA Hallmark certification label indicating assemblies meet the design requirements.

C. Mock-Up: Provide a mock-up for evaluation of installation techniques and workmanship.1. Mock-ups shall incorporate surrounding construction, including wall assembly

fasteners, flashing, and other related accessories installed in accordance with manufacturer's approved installation methods.

2. Do not proceed with remaining work until workmanship is approved by Architect.3. Modify mock-up as required to produce acceptable work.4. At Substantial Completion, approved mockups may become part of completed Work.5. Demolish mockups and remove from site.

D. Pre-installation Meeting: Conduct pre-installation meeting on site two weeks prior to commencement of installation.

1.5 DELIVERY, STORAGE, AND HANDLING

A. Deliver, store and handle materials and products in strict compliance with manufacturer's instructions and recommendations and industry standards.

B. Deliver and store assembly materials and components in manufacturer's original, unopened, undamaged containers with identification labels intact. Protect from damage.

1.6 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.7 WARRANTY

A. Manufacturer's Standard Warranty: Assemblies will be free from defects in materials and workmanship from the date of Manufacture for the time periods indicated below:1. Patio Door Units: 20 years.2. Window Units: 20 years.3. Clad Finishes: 20 years against peeling, checking, cracking caulk or color change.

08554-2

4. Pine Wood Products: Lifetime against wood decay and termites.5. Glazing:

a. Insulated Glass: 20 years against seal breakage.b. Laminated Glass: 5 years against delamination.c. Hurricane Glass: 5 years against delamination.d. Specialty Glazing: 5 years against delamination.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: JELD-WEN, Inc., which is located at: 2645 Silver Crescent Dr. Suite 400; Charlotte, NC 28273 ; Toll Free Tel: 800-535-3936; Tel: 541-850-2606; Fax: 541-851-4333; Email:request info (Architectural_Inquiries@jeld-wen.com); Web:www.jeld-wen.com

B. Substitutions: Not permitted.

C. Requests for substitutions will be considered in accordance with provisions of Section 01600.

2.2 ALUMINUM-CLAD WOOD WINDOWS AND PATIO DOORS - GENERAL

A. Design Requirements:1. Compliance: Provide assemblies capable of complying with requirements indicated,

based on testing manufacturer's window that are representative of those specified.2. Test Size: In compliance with requirements of AAMA/WDMA/CSA 101/ I.S.2/A440

(NAFS).3. Structural Requirements: Provide assemblies complying with requirements indicated:

a. Performance Class: As indicated on drawings.b. Performance Class: _________.c. Performance Grade: As indicated on drawings.d. Performance Grade: ________.

4. NFRC Requirements: Provide assemblies complying with the following total window ratings:a. U-Factor: ________ in accordance with NFRC 100.b. Solar Heat Gain Coefficient (SHGC): ________ in accordance with NFRC 200.c. Visible Transmittance (VT): ________ in accordance with NFRC 200.

B. Materials:1. Exterior Cladding: Extruded aluminum.2. Interior Wood:

a. Material: Standard, Western Pine.b. Material: Mahogany.c. Material: Vertical Grain Douglas Fir.

C. Installation Accessories:1. Flashing: Refer to Section 07 60 00 - Flashing and Sheet Metal.2. Sealants: OSI Sealants by Henkel Corporation.3. Sealants: Refer to Section 07920 - Joint Sealants.4. Sealants: Manufacturer recommended sealants to maintain watertight conditions.

D. Finishes:1. Interior Finishes for Windows:

a. Finish: Standard, unfinished.b. Finish: Optional, primed finish.c. Finish: Optional, pre-finished paint finish.

08554-3

1) Color: As Selected by Architect2) Color: Brilliant White,3) Color: Desert Sand.4) Color: Ivory.

d. Finish: Optional, pre-finished stain finish.1) Color: As Selected by Architect.2) Color: Cider3) Color: Cordovan.4) Color: Fruitwood.5) Color: Wheat.6) Color: Walnut.

e. Finish: Optional, pre-finished clear lacquer finish.2. Exterior Finishes for Windows:

a. 0.050 thick extruded aluminum cladding with finish in accordance with AAMA 2605.

b. AAMA 2605 Standard Colors.1) Color: As selected by Architect2) Color: Brilliant White3) Color: Desert Sand4) Color: Chestnut Bronze5) Color: French Vanilla6) Color: Hartford Green7) Color: Mesa Red8) Color: Arctic Silver9) Color: Dark Chocolate10) Color: Black Licorice

c. AAMA 2605 Optional Colors:1) Color: As selected by Architect2) Color: Hunter Green3) Color: Redwood4) Color: Heirloom White5) Color: Sage Brown6) Color: Smoke7) Color: Bone White8) Color: Cascade Blue9) Color: Dark Buckskin10) Color: Ivory11) Color: Luxury Bronze12) Color: Mocha Cream13) Color: Seafoam14) Color: Steele Gray15) Color: Luxury White16) Color: Luxury Champagne17) Color: Luxury Cambridge18) Color: Black Emerald19) Color: Capri Blue20) Color: Clover Mist21) Color: Light Buckskin22) Color: Dark Ivy23) Color: Deep Summer24) Color: Garnet25) Color: Haverstraw26) Color: Hudson Blue27) Color: Ivy28) Color: Liberty Blue29) Color: Mosaic Green

08554-4

30) Color: Pueblo Tan31) Color: Rosewood32) Color: Scarlet Haze33) Color: Teal34) Color: Wedgewood

d. Pre-Finished Clad Sash Only Color: As Selected by Architect.e. Pre-Finished Clad Sash Only Color: Natural Copper.f. Pre-Finished Clad Sash Only Color: Speckled Patina Copper.g. Pre-Finished Clad Sash Only Color: Hand Rubbed Copper.

3. Interior Finishes for Patio Doors:a. Finish: Standard, unfinished.b. Finish: Optional, primed finish.c. Finish: Optional, pre-finished paint finish.

1) Color: As Selected by Architect2) Color: Brilliant White,3) Color: Desert Sand.4) Color: Ivory.

d. Finish: Optional, pre-finished stain finish.1) Color: As Selected by Architect.2) Color: Cider3) Color: Cordovan.4) Color: Fruitwood.5) Color: Wheat.6) Color: Walnut.

e. Finish: Optional, pre-finished clear lacquer finish.4. Exterior Finishes for Patio Doors:

a. AAMA 2605 Standard Colors:1) Color: As selected by Architect2) Color: Brilliant White3) Color: Desert Sand4) Color: Chestnut Bronze5) Color: French Vanilla6) Color: Hartford Green7) Color: Mesa Red8) Color: Arctic Silver9) Color: Dark Chocolate10) Color: Black Licorice

b. AAMA 2605 Optional Colors:1) Color: As selected by Architect.2) Color: Hunter Green3) Color: Redwood4) Color: Bone White5) Color: Heirloom White6) Color: Sage Brown7) Color: Smoke8) Color: Cascade Blue9) Color: Dark Buckskin10) Color: Ivory11) Color: Luxury Bronze12) Color: Mocha Cream13) Color: Sea Foam14) Color: Steele Gray15) Color: Luxury White16) Color: Luxury Champagne17) Color: Luxury Cambridge18) Color: Black Emerald

08554-5

19) Color: Capri Blue20) Color: Clover Mist21) Color: Light Buckskin22) Color: Dark Ivy23) Color: Deep Summer24) Color: Garnet25) Color: Haverstraw26) Color: Hudson Blue27) Color: Ivy28) Color: Liberty Blue29) Color: Mosaic Green30) Color: Pueblo Tan31) Color: Rosewood32) Color: Scarlet Haze33) Color: Teal34) Color: Wedgewood

c. Pre-Finished Clad Sash Only Color: As selected by Architect.d. Pre-Finished Clad Sash Only Color: Natural Copper.e. Pre-Finished Clad Sash Only Color: Speckled Patina Copper.f. Pre-Finished Clad Sash Only Color: Hand Rubbed Copper.

2.3 ALUMINUM CLAD WOOD WINDOW ASSEMBLlES

A. Basis of Design: Custom Series Clad wood window assemblies as manufactured by JELD-WEN, Inc.1. Window Type: Awning windows.2. Window Type: Casement windows.3. Window Type: Double-hung windows.4. Window Type: Horizontal sliding windows.5. Window Type: Radius and geometric windows.6. Construction: Direct-set, sashless with glazing direct set to frame.7. Construction: In-sash, sash fixed or operable with hardware and accessories as

specified herein, scheduled and indicated on Drawings.

B. Window Fabrication:1. Window Type: Awning windows.

a. Frame: Corner joints mechanically fastened.b. Sash: Corner joints mortised and tenoned.c. Glass: Mounted using silicone glazing compound on exterior and acrylic sealant

on interior, secured with interior applied profiled wood stops.1) Glazing Bead: Traditional Beveled.2) Glazing Bead: Contemporary Squared.

2. Window Type: Casement windows.a. Frame: Corner joints mechanically fastened.b. Sash: Corner joints mortised and tenoned.c. Glass: Mounted using silicone glazing compound on exterior and acrylic sealant

on interior, secured with interior applied profiled wood stops.1) Glazing Bead: Traditional Beveled.2) Glazing Bead: Contemporary Squared.

3. Window Type: Double-hung windows.a. Frame: Corner joints mechanically fastened.b. Sash: Corner joints mortised and tenoned, glued and nailed from interior.c. Glass: Mounted using silicone glazing compound on exterior, secured with

interior applied profiled wood stops.1) Glazing Bead: Traditional Beveled.2) Glazing Bead: Contemporary Squared.

08554-6

3) Glazing Bead: Flush4. Window Type: Horizontal sliding windows.

a. Frame: Corner joints mechanically fastened.b. Sash: Corner joints mortised and tenoned, glued and nailed from interior.c. Glass: Mounted using silicone glazing compound on exterior, secured with

interior applied profiled wood stops.1) Glazing Bead: Traditional Beveled.2) Glazing Bead: Contemporary Squared.3) Glazing Bead: Flush

5. Window Type: Radius and geometric direct set windows.a. Frame: Corner joints are mechanically fastened.b. Glass: Mounted using silicone glazing compound on exterior then secured with

interior applied profiled wood stops.1) Glazing Bead: None

6. Window Type: Radius and geometric in-sash windows.a. Frame: Corner joints mechanically fastened.b. Sash: Standard size units with corner joints mortised and tenoned.c. Sash: Custom size units with mitered corner joints.d. Glass: Mounted using silicone glazing compound on exterior and acrylic sealant

on interior, secured with interior applied profiled wood stops.1) Glazing Bead: Traditional Beveled.2) Glazing Bead: Contemporary Squared.

C. Frames:1. Material: Select kiln-dried pine AuraLast treated wood.2. Cladding: 0.050 inch (1.27mm) extruded aluminum.3. Jamb Width: Casement, Awning and Geometric units: 3-3/8 inches (85.7 mm).4. Jamb Width: Double-Hung and Gliding units: 4-9/16 inches (116 mm).

D. Sashes: Select kiln-dried pine AuraLast treated wood.1. Cladding: 0.019 inch (0.438mm) roll-formed aluminum.2. Sash Thickness for Awning Windows: 2-3/32 inches (53.2 mm).3. Sash Thickness for Casement Windows: 2-3/32 inches (53.2 mm).4. Sash Thickness for Double-Hung Windows: 1-7/16 inches (36.5 mm).5. Sash Thickness for Horizontal Sliding Windows: 1-7/16 inches (36.5 mm).6. Sash Thickness for Radius and Geometric In-Sash Windows: 2-3/32 inches (53.2

mm).

E. Exterior Trim:1. As selected from Manufacturer's standard offering2. Casing: Standard, Extruded Aluminum Brickmould3. Casing: Optional, 3-1/2 inches (88.9 mm) Flat Casing.4. Casing: Optional, Adams Casing.5. Casing: Optional, Manchester Casing.6. Casing: Optional, Pendleton Casing.7. Sills: Standard, sill nose8. Sills: Optional, extended sill nose

F. Factory Applied Extension Jambs: Provide at all four sides of frame interior.1. For Awning Windows: 4/4 for up to 7-15/16 inch (202 mm).2. For Awning Windows: 5/4 up to 12-1/2 inch (317 mm).3. For Awning Windows: 5/4 to 4/4 Reveal for up to 9-1/8 inch (232 mm).4. For Casement Windows: 4/4 up to 7-15/16 inch (202 mm).5. For Casement Windows: 5/4 for up to 12-1/2 inch (317 mm).6. For Casement Windows: 5/4 to 4/4 Reveal for up to 9-1/8 inch (232 mm)7. For Double-Hung Windows: 4/4 up to 9-1/8 inch (231.8 mm).

08554-7

8. For Horizontal Sliding Windows: 4/4 up to 9-1/8 inches (231.8 mm).9. For Radius and Geometric Windows: 4/4 for up to 7-15/16 inch (202 mm).10. For Radius and Geometric Windows: 5/4 up to 12-1/2 inch (317 mm).11. For Radius and Geometric Windows: 5/4 to 4/4 Reveal for up to 9-1/8 inch (232 mm).

G. Weatherstripping:1. Awning Windows: Foam lined bulb seal between sash interior and frame with

secondary leaf seal between sash edge and frame.2. Casement Windows: Foam lined bulb seal between sash interior and frame with

secondary leaf seal between sash edge and frame.3. Double-Hung Windows: Concealed non-compression jamb liner forming compression

seal with dual durometer bulb seal against sash stiles and between top and bottom rails of sash and frame, bulb seal between top rail and header and between sash meeting rails.

4. Horizontal Sliding Windows: Compression bulb seal at sash and foam filled vinyl at exterior sides and head jamb.

5. Radius and Geometric Windows: Foam lined bulb seal between sash interior and frame with secondary leaf seal between sash edge and frame.

H. Window Hardware:1. Awning Windows:

a. Hinges: Standard, corrosion resistant steel.b. Hinges: Optional, Stainless steel.c. Operator: Standard, lever lock.d. Operator: Steel roto gear with heavy gauge scissor operating arm.e. Operator: Stainless steel roto gear with heavy gauge scissor operating arm.f. Locks: Concealed.g. Handle Profile: Standard handle, manual folding crank.h. Handle Profile: Optional, round handle.i. Handle Profile: Nonej. Finish: As Selected by Architect.k. Finish: Standard, Chestnut Bronze finish.l. Finish: Standard, Desert Sand finish.m. Finish: Standard, White finish.n. Finish: Optional, Antique Brass finish.o. Finish: Optional, Brushed Chrome finish.p. Finish: Optional, Satin Nickel finish.q. Finish: Optional, Polished Brass finish.r. Finish: Optional, Polished Chrome finish.s. Finish: Optional, Oil-Rubbed Bronze finish.t. Finish: Optional, Black Powder Coat finish.

2. Casement Windows:a. Hinges: Standard, Stainless steel.b. Operator: Hardened stainless steel worm gears and dual action heavy gauge

stainless steel operating arm.c. Locks: Concealed.d. Handle Profile: Standard handle, manual folding crank.e. Handle Profile: Optional handle manual crank, round handle.f. Handle Profile: No Handleg. Finish: As Selected by Architect.h. Finish: Standard, Chestnut Bronze finish.i. Finish: Standard, Desert Sand finish.j. Finish: Standard, White finish.k. Finish: Optional, Antique Brass finish.l. Finish: Optional, Brushed Chrome finish.m. Finish: Optional, Satin Nickel finish.

08554-8

n. Finish: Optional, Polished Brass finish.o. Finish: Optional, Polished Chrome finish.p. Finish: Optional, Oil-Rubbed Bronze finish.q. Finish: Optional, Black Powder Coat finish.

3. Double-Hung Windows:a. Balances: Concealed block and tackle.b. Sash Retainers: Recessed top sash, concealed bottom sashc. Locks: Standard, Cam action. (One lock controls bottom sash retainers)d. Locks: Optional, Deluxe cam lock with concealed tilt latche. Locks: Optional, Keyed cam lockf. Locks: Interior sash lift.g. Finish: As Selected by Architect.h. Finish: Standard, Chestnut Bronze finish.i. Finish: Standard, Desert Sand finish.j. Finish: Standard, White finish.k. Finish: Optional, Antique Brass finish.l. Finish: Optional, Brushed Chrome finish.m. Finish: Optional, Satin Nickel finish.n. Finish: Optional, Polished Brass finish.o. Finish: Optional, Polished Chrome finish.p. Finish: Optional, Oil-Rubbed Bronze finish.q. Finish: Optional, Black Powder Coat finish.

4. Horizontal Sliding Windows:a. Sliding System: Vinyl track and sash reduced friction buttons.b. Sash Pull: Surface mounted.c. Sash Lock: Surface mounted, cam action.d. Sash Lock: Surface Mounted, keyed cam action.e. Finish: As Selected by Architect.f. Finish: Standard, Chestnut Bronze finish.g. Finish: Standard, Desert Sand finish.h. Finish: Standard, White finish.i. Finish: Optional, Antique Brass finish.j. Finish: Optional, Brushed Chrome finish.k. Finish: Optional, Satin Nickel finish.l. Finish: Optional, Polished Brass finish.m. Finish: Optional, Polished Chrome finish.n. Finish: Optional, Oil-Rubbed Bronze finish.o. Finish: Optional, Black Powder Coat finish.

5. Radius and Geometric In-Sash Windowsa. Hinges: Standard, Stainless steel.b. Operating Sash: Stainless steel leaf.c. Operator: Hardened steel worm gears and heavy gauge steel arm.

1) For Operable Octagon-Shaped Window: Single arm pull scissor with roto handle.

d. Locks: Concealed.e. Handle Profile: Standard handle, manual folding crank.f. Handle Profile: Optional, manual crank, round handle.g. Handle Profile: Optional, No Handle.h. Finish: As selected by Architect.i. Finish: Standard, Chestnut Bronze finish.j. Finish: Standard, Desert Sand finish.k. Finish: Standard, White finish.l. Finish: Optional, Antique Brass finish.m. Finish: Optional, Brushed Chrome finish.n. Finish: Optional, Satin Nickel finish.o. Finish: Optional, Polished Brass finish.

08554-9

p. Finish: Optional, Polished Chrome finish.q. Finish: Optional, Oil-Rubbed Bronze finish.r. Finish: Optional, Black Powder Coat finish.

6. Radius and Geometric Direct Set Windows: None

I. Glazing for Windows:1. Strength: Standard, tempered glass.2. Strength: Optional, laminated glass.3. Glazing Type: Insulated glass.

a. Description: Two panes of glass utilizing continuous roll formed stainless steel spacer and dual seal sealants.

b. Overall Nominal Thickness: Awning, Casement, Radius and Geometric In-Sash: 15/16 inch (23.8 mm).

c. Overall Nominal Thickness: Double-Hung, Horizontal Sliding and Geometric and Radius Direct-Set: 3/4 inch (19 mm).

d. Glass Coating: Standard, Low-E 366.e. Glass Type: Optional, Low-E.f. Glass Coating: Optional, Low-E 180.g. Glass Coating: Optional, Low-E EC.h. Glass Coating: Optional, Low-E 366 EC.i. Glass Protection: Plastic preserve film on interior and exterior of glass.j. Air Space: Standard, Argon-filled airspace.k. Air Space: Optional, air-filled airspace with capillary tubes.

4. Glazing Type: Triple Glazing.a. Overall Nominal Thickness: 1/8 inch (3 mm).b. Overall Nominal Thickness: 3/16 inch (7 mm).c. Glass Coating: Standard, Low-E.d. Glass Coating: Optional, Low-E Obscure.e. Glass Coating: Optional, Low-E Rain.f. Glass Coating: Optional, Low-E Glue Chip.g. Glass Coating: Optional, Low-E Seedy Reamy.

J. Exterior Insect Screens:1. Material: Charcoal fiberglass screen cloth (18 by 16 mesh) set in painted roll formed

aluminum frame.2. Frame Color: As selected by Architect.3. Frame Color: Black Licorice.4. Frame Color: Brilliant White.5. Frame Color: Chestnut Bronze.6. Frame Color: Desert Sand.7. Frame Color: French Vanilla.8. Frame Color: Hartford Green.9. Frame Color: Heirloom White.10. Frame Color: Hunter Green.11. Frame Color: Mesa Red.12. Frame Color: Redwood.13. Frame Color: Sage Brown.14. Frame Color: Smoke.15. Frame Color: Matched Custom Color.

K. Interior Insect Screens:1. Material: Charcoal fiberglass screen cloth (18 by 16 mesh) set in painted roll formed

aluminum frame.a. Finish: As selected by Architect.b. Finish: Brilliant Whitec. Finish: Desert Sand.

08554-10

d. Finish: Chestnut Bronzee. Finish: Arctic Silverf. Finish: Black Licorice

2. Material: Charcoal fiberglass screen cloth (18 by 16 mesh) set in wood veneer roll formed aluminum frame.a. Finish: As selected by Architect.b. Finish: Western Pinec. Finish: Mahogany.d. Finish: Vertical Grain Douglas Fir.

3. Material: Charcoal fiberglass screen cloth (18 by 16 mesh) set in painted roll formed aluminum frame - enclosed in solid wood frame (swinging screens). Push-out casement only.a. Finish: As selected by Architect.b. Finish: Western Pine.c. Finish: Mahogany Pine.d. Finish: Vertical Grain Douglas Fir.

L. Grilles:1. Type: Simulated Divided Lites (SDL).

a. Exterior Muntins:1) Material: Extruded aluminum permanently applied to exterior of insulating

glass unit.2) Profiles: Beaded stop profiles.

a) Profile Width: 5/8 inch (15.9 mm).b) Profile Width: 7/8 inch (22 mm).c) Profile Width: 1-1/8 inches (28.5 mm).d) Profile Width: 1-3/8 inches (34.9 mm).e) Profile Width: 2-5/16 inches (59 mm) for simulated double-hung

checkrail.3) Profiles: Putty profiles.

a) Profile Width: 5/8 inch (15.9 mm).b) Profile Width: 7/8 inch (22 mm).c) Profile Width: 1-1/8 inches (28.5 mm).d) Profile Width: 1 inch (25.4 mm) copper.e) Profile Width: 1-3/8 inches (34.9 mm).f) Profile Width: 2-5/16 inches (58.7 mm)

4) Pattern: As scheduled and indicated on Drawings.5) Finish:

a) Color: As Selected by Architect:b. Internal Shadow Bar:

1) Standard: Light Bronze finish.2) Optional: Silver finish.

c. Interior Spacer Bars:1) Standard: Steel2) Optional: Black3) Optional: Gray

d. Interior Muntins:1) Material: Clear pine permanently bonded to interior of insulating glass

unit.2) Material: Optional Alder permanently bonded to interior of insulating

glass unit.3) Material: Optional Fir permanently bonded to interior of insulating glass

unit.4) Material: Optional Mahogany permanently bonded to interior of insulating

glass unit.5) Profile: Match exterior muntin.

08554-11

2. Type: Full Surround Wood Grilles.a. Material: Unfinished clear pine.b. Profile: Modified OGEE.c. Pattern: As scheduled and indicated on Drawings.d. Size: 7/8 inch (22 mm).e. Size: 1-1/8 inches (28.5 mm).f. Size: 1-3/8 inches (34.9 mm).

3. Type: Grilles Between the Glass (GBG).a. Material: Made of roll formed aluminum suspended within the air cavity.b. Profile: Flat.

1) Profile Width: Flat profile 5/8 inch (15.9 mm).c. Profile: Contour.

1) Profile Width: Contour profile, 23/32 inch (18.25 mm).2) Profile Width: Contour profile, 1 inch (25.4 mm).

d. Pattern: As scheduled and indicated on Drawings.e. Finish: As selected by Architect.f. Finish: Brilliant White.g. Finish: Chestnut Brown.h. Finish: Desert Sand.i. Finish: French Vanilla.j. Finish: Hartford Green.k. Finish: Mesa Red.

2.4 WOOD PATIO DOOR ASSEMBLlES

A. Basis of Design: Custom Series aluminum-clad-wood patio door assemblies as manufactured by JELD-WEN, Inc.1. Patio Door Type: In-swing patio doors, wood construction2. Patio Door Type: Out-swing patio doors, wood construction.3. Patio Door Type: Sliding patio doors, wood construction.

B. Patio Door Fabrication:1. Frame: Top and bottom rails are solid pine veneer laminated to kiln dried edge-and-

end-glued core. Stiles are same veneer laminated to Timberstrand core.2. Glass: Mounted using silicone glazing compound on exterior and acrylic sealant on

interior.3. Cladding: Aluminum corners are jointed and sealed.

C. Frames:1. Material: Select kiln-dried pine AuraLast treated wood.2. Jamb Width: 4-9/16 inches (116 mm).3. Cladding: 0.055 inch (1.27 mm) extruded aluminum4. Radius Frames: 90 inch (2286 mm).5. Radius Frames: 31-5/16 inch (795.3 mm).6. Radius Frames: 37-5/16 inch (948.8 mm).

D. Swinging Door Panels:1. Material: Select kiln-dried pine AuraLast treated wood and Timberstrand engineered

wood substrate.2. Cladding: 0.024 inch (0.61 mm)3. Thickness: 1-23/32 inch (43.7 mm).4. Stiles and Rail:

a. 4-5/8 inch (117.5 mm) top rail and stiles, 6-5/8 inch (168.3 mm) bottom rails.

E. Sliding Door Panels:1. Material: Select kiln-dried pine AuraLast treated wood and Timberstrand engineered

wood substrate.

08554-12

2. Cladding: 0.055 inch (1.4 mm) extruded aluminum3. Thickness: 1-23/32 inch (43.7 mm).4. Stiles and Rail:

a. Narrow: 2-3/4 inch (69.6 mm) stiles and rails.b. Wide: 4-5/8 inch (117.5 mm) top rail and stiles, 6-5/8 inch (168.3 mm) bottom

rails.

F. Exterior Trim:1. As selected from Manufacturer's standard offering.2. Casing: Standard, Extruded Aluminum Brickmould3. Casing: Optional, 3-1/2 inches (88.9 mm) Flat Casing.4. Casing: Optional, Adams Casing.5. Casing: Optional, Manchester Casing.6. Casing: Optional, Pendleton Casing.

G. Extension Jambs: Factory applied on all four sides of frame interior, in wall depths up to 6-9/16 inch (166.7 mm).

H. Weatherstripping:1. Sliding Patio Door:

a. Foam filled vinyl wrapped strips at head and side jambs, polypropylene pile-sealing strip at bottom of operating panel, vinyl interlocks and compressible foam filled bulbs at meeting stiles.

2. Out-Swing Patio Door:a. Continuous dual foam filled bulb seal compressed between exterior of panel

and all four sides of frame.3. In-Swing Patio Door:

a. Continuous dual foam filled bulb seal compressed between exterior of panel and all three sides of frame.

I. Hardware:1. Sliding Patio Doors:

a. Sliding System: Steel ball bearing tandem rollers in heavy duty housing with cam type slip proof height adjustment.

b. Locks: Standard, single point mortise.c. Locks: Optional, automatically activated multipoint system.d. Handle Set: Standard, Premium Handlee. Handle Set: Optional, Contemporary Handlef. Handle Set: Optional, Legacy Handleg. Handle Set: Optional, No Handleh. Finish: As selected by Architect.i. Finish: As selected from manufacturer's standard offering.j. Sill: Standard, Tan colored pultruded fiberglass with solid oak interior trim and

stainless steel track cap.k. Sill: Optional, Dark Bronze colored pultruded fiberglass with solid oak interior

trim and stainless steel track cap.2. Out-Swing Doors:

a. Hinges: Standard, Optional, adjustable 4x4 heavy gauge solid brass with stainless steel pins.

b. Hinges: Optional, Ball bearing hinge.c. Hinges: Optional, 4 1/2 inch ball bearing hinge with square corners.d. Locks: Standard, multi-point mortise with lever handle and thumb turn dead

bolt.e. Locks: Optional, manually activated multipoint system.f. Handle Set: Standard, Traditional Handle.g. Handle Set: Optional, Contemporary Handle.

08554-13

h. Handle Set: Optional, Rustic Handle.i. Handle Set: Optional, No Handlej. Finish: As selected by Architect.k. Finish: As selected from manufacturer's standard offering.l. Sill: Dark bronze anodized aluminum with interior oak trim and vinyl fin-and-

bulb door sweep.1) Compliance: Optional, 1/2 inch (12.7 mm) maximum height to meet ADA

requirements.3. In-Swing Doors:

a. Hinges: Standard, Optional, adjustable 4x4 heavy gauge solid brass with stainless steel pins.

b. Hinges: Optional, Ball bearing hinge.c. Hinges: Optional, 4 1/2 inch ball bearing hinge with square corners.d. Locks: Standard, multi-point mortise with lever handle and thumb turn dead

bolt.e. Locks: Optional, manually activated multipoint system.f. Handle Set: Standard, Traditional Handle.g. Handle Set: Optional, Contemporary Handle.h. Handle Set: Optional, Rustic Handle.i. Handle Set: Optional, No Handlej. Finish: As selected by Architect.k. Finish: As selected from manufacturer's standard offering.l. Sill: Dark bronze anodized aluminum with interior oak trim and adjustable oak

threshold in combination with vinyl fin-and-bulb door sweep.1) Compliance: Optional, 1/2 inch (12.7 mm) maximum height to meet ADA

requirements.

J. Glazing for Patio Doors:1. Strength: Standard, tempered glass.2. Strength: Optional, laminated glass.3. Glazing Type: Insulated glass.

a. Description: Two panes of glass utilizing continuous roll formed stainless steel spacer and dual seal sealants.

b. Overall Nominal Thickness: 3/4 inch (19 mm).c. Glass Coating: Standard, Low-E 366 Tempered.d. Glass Coating: Optional, Low-E Tempered.e. Glass Coating: Optional, Low-E 180 Tempered.f. Glass Coating: Optional, Low-E EC Tempered.g. Glass Coating: Optional, Low-E EC 366 Tempered.h. Glass Coating: Optional, As selected by Architect.i. Glass Protection: Plastic preserve film on interior and exterior of glass.j. Air Space: Standard, Argon-filled airspace.k. Air Space: Optional, air-filled airspace with capillary tubes.

K. Exterior Sliding Insect Screens: (Optional swinging screens for inswing doors)1. Material: Charcoal fiberglass mesh (18 by 16 mesh) set in extruded aluminum frame.

a. Frame Color: As selected by Architect.b. Frame Color: Black Licorice.c. Frame Color: Brilliant White.d. Frame Color: Chestnut Bronze.e. Frame Color: Desert Sand.f. Frame Color: French Vanilla.g. Frame Color: Hartford Green.h. Frame Color: Heirloom White.i. Frame Color: Hunter Green.j. Frame Color: Mesa Red.

08554-14

k. Frame Color: Redwood.l. Frame Color: Sage Brown.m. Frame Color: Smoke.n. Frame Color: Matched Custom Color.

L. Grilles:1. Type: Simulated Divided Lites (SDL).

a. Exterior Muntins:1) Material: Extruded aluminum permanently applied to exterior of insulating

glass unit.2) Profiles: Beaded stop profiles.

a) Profile Width: 5/8 inch (15.9 mm).b) Profile Width: 7/8 inch (22 mm).c) Profile Width: 1-1/8 inches (28.5 mm).d) Profile Width: 1-3/8 inches (34.9 mm).

3) Profiles: Putty profiles.a) Profile Width: 5/8 inch (15.9 mm).b) Profile Width: 7/8 inch (22 mm).c) Profile Width: 1-1/8 inches (28.5 mm).d) Profile Width: 1-3/8 inches (34.9 mm).e) Profile Width: 2-5/16 inches (58.7 mm)

4) Pattern: As scheduled and indicated on Drawings.5) Finish:

a) As selected by Architect.b. Internal Shadow Bar:

1) Standard, Light Bronze finish.2) Optional, Silver finish.

c. Interior Spacer Bars:1) Standard: Steel2) Optional: Black3) Optional: Gray

d. Interior Muntins:1) Material: Clear pine permanently bonded to interior of insulating glass

unit.2) Profile: Match exterior muntin.

2. Type: Full Surround Wood Grilles.a. Material: Unfinished clear pine.b. Profile: Rectangular.c. Pattern: As scheduled and indicated on Drawings.d. Size: 7/8 inch (22 mm).e. Size: 1-1/8 inches (28.5 mm).f. Size: 1-3/8 inches (34.9 mm).

3. Type: Grilles Between the Glass (GBG).a. Material: Made of roll formed aluminum suspended within the air cavity.b. Profile: Flat.

1) Profile Width: Flat profile 5/8 inch (15.9 mm).c. Profile: Contour.

1) Profile Width: Contour profile, 23/32 inch (18.25 mm).2) Profile Width: Contour profile, 1 inch (25.4 mm).

d. Pattern: As scheduled and indicated on Drawings.e. Finish: As selected by Architect:f. Finish: Brilliant White.g. Finish: Chestnut Brown.h. Finish: Desert Sand.i. Finish: French Vanilla.j. Finish: Hartford Green.

08554-15

k. Finish: Mesa Red.

PART 3 EXECUTION

3.1 EXAMINATION AND PREPARATION

A. Inspect and prepare openings and substrates using the methods recommended by the manufacturer for achieving best result for the substrates under project conditions.1. Inspect assembly components prior to installation.2. Verify rough opening conditions are within recommended tolerances.3. Form sheet metal sill pan in accordance with manufacturer's recommendations.4. Prepare assembly components for installation in accordance with manufacturer's

recommendations.

B. Do not proceed with installation until openings and substrates have been prepared using the methods recommended by the manufacturer and deviations from manufacturer's recommended tolerances are corrected. Commencement of installation constitutes acceptance of conditions.

C. If preparation is the responsibility of another installer, notify Architect in writing of deviations from manufacturer's recommended installation tolerances and conditions.

3.2 INSTALLATION

A. Install assemblies in accordance with manufacturer's installation guidelines and recommendations including the following.

B. Installation of Windows With Nailing Fins: Insert windows into rough opening.1. Shim side jambs straight.2. Inspect window for square, level and plumb.3. Fasten window through nailing fins around entire window.4. Test and adjust for smooth operation of window.5. Set all nails below wood surface.

C. Installation of Patio Doors With Nailing Fins: Insert patio doors into rough opening.1. Shim side jambs straight.2. Inspect patio door for square, level and plumb.3. Fasten patio door through nailing fins around entire patio door.4. Test and adjust for smooth operation of patio door.

3.3 FIELD QUALITY CONTROL

A. Manufacturers' Field Services: Perform field inspections as recommended by manufacturer.

3.4 CLEANING AND PROTECTION

A. Clean the exterior surface and glass with mild soap and water.

B. Protect installed windows from damage.

C. Remove and dispose of protective film from glass; touch-up, repair or replace damaged components and assemblies before Substantial Completion.

END OF SECTION

08554-16