©2019 Mid West Products, Inc. -1- Form No. M15-1603

VEGETABLE GARDEN SEED ROW PLANTER MODEL GSF-31M-NT

No Tools Required Owner’s Manual and Parts List

SAVE THIS MANUAL

You will need this manual for the safety instructions, assembly instructions and parts list. Put it in a safe, dry place for future reference. Additional Information/Link to PDF Copy of this Manual:

©2019 Mid West Products, Inc. -2- Form No. M15-1603

VEGETABLE GARDEN SEED ROW PLANTER AND FERTILIZER APPLICATOR

➢ NO TOOLS ASSEMBLY ➢ OPERATING

➢ MAINTENANCE ➢ PARTS LISTING

ASSEMBLY

1. Remove two Wing Nuts (37) from the Hex Bolts (44) which are located at the top of Lower Handle Tubes (10). Install the Upper Handle Tube (11) onto the Hex Bolts (44) in the Lower Handle Tubes (10) and secure with previously removed Wing Nuts (37).

2. Remove Wing Nut (37) from Hex Bolt (45) in the fertilizer section of the Seed/Fertilizer Hopper (1). Install Fertilizer Lever (19) onto Hex Bolt (45) and secure with previously removed Wing Nut (37).

3. Unscrew Plastic Knob (48) from Row Marker Tube (21).

4. Assemble Row Marker Tube (21) to the Row Marker Bracket (20) using the Hex Bolt (38) that is inserted into the end of the Row Marker Tube (21), with the head of the Hex Bolt pointing away from the Seed/Fertilizer Hopper (1).

5. Screw the previously removed Plastic Knob (48) onto the Hex Bolt (38) to assemble the Row Marker Tube (21) to the Row Marker Bracket (20). Do not fully tighten hardware, allowing row Marker Tube to pivot from side to side.

OPERATION

1. To install the desired Seed Plate, hold the Seed Plate at an angle with the bottom against the straight wall in the Hopper. Line up the slots in the Seed Plate with the raised portions of the Hub, hold it firmly against the inside of the Hopper and rotate it approximately ½” in the “ON” direction as indicated by the arrow on the Plate until the cam action locks the Seed Plate in place on the Hub. Do Not Force! OFF and ON directions are indicated on the Seed Plates with arrows.

2. Next, set the planting depth with the wedge-shaped Furrowing Shoe located directly under the Hopper. Move Furrowing Shoe until top edge is in line with desired planting depth. Retighten Wing Nut (35) after adjustment is made. Check the depth by moving the Seeder forward a few inches.

3. Pour seeds in the Seed Hopper. CAUTION: Do not fill the Hopper above the center of the Seed Plate.

4. Pour fertilizer into fertilizer hopper. CAUTION: Do not over fill the Hopper. Allow 1” from fertilizer to top edge of Hopper.

5. Adjust fertilizer flow by loosening Wing Nut on Fertilizer Hopper. Slide calibrated plate to desired setting and tighten Wing Nut. Before filling, shut off Fertilizer Control.

6. Mark out the first row in your garden. Lower the Row Marker Shaft and adjust the Row Marker to the proper width for the next row. You are now ready to plant

7. To empty seeds, remove Plug (2) from Seed Hopper by simply putting pressure on center of Plug and push inward. Pour seeds into a clean container.

8. Empty fertilizer by placing a clean container under Fertilizer Hose, setting Adjustment Plate to No. 3 setting and open control, allowing fertilizer to flow into the container.

9. To remove Seed Plate, hold Pulley and Belt stationary with one hand and rotate the Seed Plate approximately ½” in the “OFF” direction indicated by an arrow on top of the

©2019 Mid West Products, Inc. -3- Form No. M15-1603

Seed Hopper. Push the Seed Plate off the Hub through the hole just above the Pulley. It will slip off easily.

NOTICE: Keep your Seed/Fertilizer Hopper clean and free from sand, grit, and seed treating materials.

SEED PLATE SELECTION GUIDE

Selection information as to seed size and spacing are also found on your Seed Plates.

15-1018-1 Has a 9 inch seed drop spacing, plants corn and sunflowers.

15-1018-2 Has a 3 ½ inch seed drop spacing, plants small and medium peas and beans, also similar seeds.

15-1018-3 Has 3 ½ inch seed drop spacing, plants variety of peas and beans including baby Lima.

15-1018-4 Has a 3 ½ inch seed drop spacing, plants beets, extra small peas and beans, okra, and related seeds.

15-1018-5 Has a 3 inch seed drop spacing, plants radishes, small beets, and seed of like size.

15-1018-6 Has 4 inch drop spacing, plants most small seeds such as turnips, mustard, lettuce, carrots, kale, collards, endive, spinach, rutabaga, parsnips, parsley, and rhubarb. This plate may also be used to plant seeds for vegetable that are sometimes grown from plants. These include broccoli, brussel sprouts, cabbage, cauliflower, celery, onions, and peppers.

NOTE: When changing Seed Plates, be sure Hopper is empty.

FERTILIZER ADJUSTMENT SETTINGS

Granular Fertilizer must be free flowing without lumps. No. 1 setting – 1 lb per 100 ft. No. 2 setting – 2 lb per 100 ft. No. 3 setting – 3 lb per 100 ft.

Consult your fertilizer dealer for further application data. We recommend that Users contact their Local Ag Agent with the USDA (United States Department of Agriculture) for their recommendations on the proper fertilizers to use in their particular County.

HELPFUL OPERATING SOLUTIONS

PROBLEM:

1. The Seeder will not go more than a foot or two . . .

2. The peas, beans, and/or corn fly out of the hopper . . .

3. The seeds break . . .

SOLUTIONS:

Be extra careful, do not back up the Seeder. (Lift the Seeder to reposition the GSF 31M)

So, what happens if the Seeder is pulled backwards?

1. The Seed Plate will come loose, whenever the rear Wheel of the Seeder is pulled backwards. If the Seed Plate loosens, even a little, then seeds get caught between the Seed Plate and the side of the Seed Hopper. This causes the Seed Plate to quit turning.

2. As the rear Seeder Wheel is still being pushed, the plate tightens and seeds that are caught between the Plate and the Hopper wall, then get crushed. Once the seeds are crushed, then the Plate can’t turn and the seeds are all planted on one spot or they clog the Seed Chute.

The Upper Pulley and Spindle are too tight:

1. Remove the Belt (Item 16) — it is easiest to remove the Belt located on the Lower Pulley (Item 15) — pulling the Belt slightly to one side and at the same time.

2. Check the Upper Pulley (Item 15) that is connected to the Spindle (Item 13).

3. If the Pulley/Spindle Assembly does not spin freely or is tight, then back off the Screw (Item 40) one-fourth to one-half turn.

©2019 Mid West Products, Inc. -4- Form No. M15-1603

4. Then, place two fingers behind the Upper Pulley (Item 15). While using your thumb, push on the Screw (Item 40) with 2 or 3 pounds of pressure and pull the Pulley away from the unit.

Re-check the Pulley/Spindle Assembly:

1. Now re-check to see if the Pulley and Spindle Assembly spins more freely.

2. If the Pulley/Spindle Assembly does not spin freely, you have almost solved the problem.

3. If the Pulley/Spindle Assembly wobbles more than just a hair, it might be too loose. (There is some uptake when the Seed Plate is attached.)

Lubrication:

1. The GSF 31M is designed to not require lubrication. We mold talc into the plastic to add “lubricity”. So, if you want the Seed Plates or Spindle to be “lubricated”, use some powdered talc.

2. Some baby powders are all talc and fragrance. However, DO NOT USE the baby powder that has corn starch — or other ingredients.

Re-assemble the Belt:

1. Put the Belt onto the Upper Pulley.

2. Start the Belt back onto the Lower Pulley. Snap the Belt onto the Lower Pulley using the leverage by turning the rear Wheel (4).

PARTS LIST

Key Part No. Description Qty Key Part No. Description Qty

1 15-1160 Seed/Fertilizer Hopper 1 22 15A-1185 Row Marker Blade 1

2 15-1161 Plug (Not Illustrated) 1 23 15-1037 Row Marker Cap 1

3 15-1162 Seed Tube Cover 1 24 15-1181 Step - Fertilizer - Shut Off 1

4 15-1013 Wheel - 12” Diameter 2 31 X-1429-1 5/16-18 X 5 HHCS 2

5 15-1163 Frame Tube 2 32 15-1017 Wheel Spacer 2

6 15A-1166 Seed Tube Bracket 1 33 X-1107 5/16-18 Lock Nut 2

7 15-1167 Furrowing Shoe 1 34 L-116 5/16-18 X 1 ½ Carriage Bolt 1

8 15-1168 Support Tube 2 35 X-1007 5/16-18 Wing Nut 1

9 15-1186 Decal (Not Illustrated) 1 36 X-1318 ¼-20 X ¾ Carriage Bolt 1

10 15-1170 Lower Handle Tube 2 37 X-1152 ¼-20 Wing Nut 4

11 15-1171 Handle 1 38 L-81 5/16-18 X 1 ¼ HHCS 1

12 15A-1172 Pouch 1 39 L-276 ¼-20 X 1 ½ HHCS 2

13 15-1173 Spindle 1 40 X-1577 ¼-20 X ½ Self Tap Screw 1

14 15-1018 Seed Plate (6 Plates) 1 41 X-1433 ¼ ID X 7/8 OD Flat Washer 1

15 15-1011 Pulley 2 42 X-2020 ¼-20 X 1 HHCS 4

16 15-1174 Belt 1 43 L-303 ¼-20 Lock Nut 6

17 15-1175 Seed Tube 1 44 X-1182 ¼-20 X 1 ¼ HHCS 2

18 15-1176 Fertilizer Tube 1 45 L-172 ¼-20 X ¾ HHCS 1

19 15-1177 Fertilizer Hopper Lever 1 46 X-A1568 ¼-20 X ¾ Thumb Screw 1

20 15-1178 Row Marker Bracket 1 47 X-A1569 ¼-20 Special Nut 1

21 15-1019 Row Marker Tube 1 48 9-1622 5/16-18 Knob 1

©2019 Mid West Products, Inc. -5- Form No. M15-1603

PARTS DRAWING

©2019 Mid West Products, Inc. -6- Form No. M15-1603

GUARANTEE

The merchandise you have purchased from us has been carefully engineered and manufactured under Mid West Products rigid quality standards and should give you satisfactory, dependable operation. However, like all mechanical merchandise, it may occasionally require adjustment or maintenance. Should you need technical assistance, please contact MID WEST PRODUCTS.

INSTRUCTIONS FOR ORDERING PARTS (Minimum Parts Order Charge $20.00)

1. Address all parts orders or correspondence regarding customer service to one of the following:

Parts Dept. Phone: (937) 337-3641

Mid West Products, Inc.

P.O. Box 301 E-mail: Parts@Mid-West-Products-Inc.com

Phillipsburg, OH 45354 Website: www.Mid-West-Products-Inc.com

2. Write your name and address plainly (print or type).

3. Explain where and how to ship.

4. Give model number of unit.

5. Give part number from parts list, as well as a description, including color, of the part and the quantity

you need.

6. Inspect all shipments you receive. If any parts are damaged or missing, file a claim with the carrier

before accepting.

7. If you are returning parts, be sure to include WITH THE SHIPMENT a list of the parts with your

name and address.

8. All orders for repair and replacement parts will be shipped when paid with Master Card, Visa, or personal check/money order. Prices subject to change without notice.

©2019 Mid West Products, Inc. -7- Form No. M15-1603

A basic garden with a little planning can provide enough fresh vegetables for a family of 4-5 for a summer. We suggest a 15’ x 25’ layout that will enable you to use your new Mid West Products Seeder and/or Cultivator efficiently and economically. Select and area for your garden that has plenty of sunshine. Run the rows North and South thus allowing the plants to have about the same amount of sunshine.

©2019 Mid West Products, Inc. -8- Form No. M15-1603

WOODEN UTILITY CARTS — GC-20 OR GC-26 It has a gate that lifts out to unload bulky loads like mulch, soil, gravel, firewood or waste and also allow it to carry longer items. Once you have one, you’ll wonder what you ever did without it! The Standard-Duty Utility Cart has two 20” pneumatic wheels and a cargo capacity of 6.5 cubic feet or up to 300 pounds. The Heavy-Duty Utility Cart has two 26” pneumatic wheels and a cargo capacity of 11.3 cubic feet or up to 400 pounds.

31” DELUXE PUSH LAWN SWEEPER — B-319

• The “Butterfly” Handles Increase the Hamper Capacity to a Huge 8.5-Bushel.

• Big 10” Precision Molded Plastic Wheels with Ribbed Tread Rubber Tire . . . Makes this Unit Easy to Push.

• The Rear Swivel Casters Help Make this Easy to Maneuver.

• Our Easy to Operate One-Hand “Squeeze Me” Height Adjustment Makes it Easy to go From Grass to Pavement.

• The Removable Hamper Allows for Easy Dumping and Fold Away Storage.

OTHER LAWN & GARDEN TOOLS FROM

MID WEST PRODUCTS, INC.

HIGH WHEEL CULTIVATOR — HWC-243A

• 24” Steel Wheel For Easy Handling.

• Special Selection of 3 Tools (Mol-board Plow, Reversible Shovel, Welded Five-Tine Cultivator).

• Slotted Foot For Plow Attachments Enables Easy Adjustment of Cutting Depth and Angle.

• Adjustable Handle Height for more comfortable use.

• Handle Folds Easily For Storage or Transportation.

“TRACTOR SEAT ON WHEELS”/HANDY CADDY — GC-400R Sit comfortably on the sturdy four-wheeled Handy Caddy to do any of the jobs that usually require stooping, squatting, or kneeling. The 360° Swivel Seat allows freedom of movement while working in the garden or the greenhouse. Tools and supplies are held within easy reach in the handy Shelf below the Seat. Tasks, such as at your planter’s bench or in the actual garden becomes easier and fun! At a weight of 34 pounds, this item is durable, easy to use, comfortable, and ….yes….EASY on the KNEES! It has many wonderful uses, just use your imagination!!! It is the ULTIMATE HELPER! Get up off your aching knees and onto a “Tractor Seat on Wheels” today!