utilaj spalare camioane

ATLAS MANUAL 10/09/06

THREE BRUSH ROLLOVER OR STATIONARY

TRUCK WASH SYSTEM

SALES MANUAL

The Finest Vehicle Wash Systems


TABLE OF CONTENTS

1. RYKO® Brochure

2. Features & Benefits

3. Description Basic Atlas, plus Options and Accessories Summary

4. Description of Operation

5. Drawings

6. Technical Data

7. Preventive Maintenance

8. Order Information


ATLAS

FEATURES, BENEFITS AND SELLING HIGHLIGHTS

• Hot Dipped Galvanized and Painted Frame

• Direct drive motors

• Hot Dipped Galvanized Tracks (18 m. long)

• Electrically operated only (no need for air compressor

• Power-on Light

• Diagnostic lights for each I/O port

• Side brushes move independently on a stainless steel guide rail

• Manual frost protection

• PLC controlled

• Amp sensing top brush with safety features

• Customer appealing design and appearance

• Manual or Coin/Token activation

• Traffic lights assist positioning the vehicle (optional)

• Two optional chemical pumps are available for pre-soak, rinse and/or wax.

• Four Factory pre-set wash programs

• Standard 4,60 m. Wash Height


ATLAS DESCRIPTION Options & Accessories

A3101 THREE BRUSH BASIC WASH EQUIPMENT (Height: 4.60 m)

Designed to be a rollover or stationary drive-thru system. The steel frame is hot dipped galvanized, epoxy painted and is guaranteed for seven years. The ATLAS operates entirely on electricity, it requires no air, and is PLC controlled for easy programming and service. Two direct drive motors power the gantry, one on each side. The side brushes are mounted on independent carriages and traverse along two inclined stainless steel guide rails. The side brushes profile the vehicle using a combination of gravity, proximity switches and current sensors. Both the carriage and guide rails oscillate for optimum washing flexibility. The horizontal brush is suspended by a stainless steel cable and counterweighted for a smooth vertical movement along the guides. The horizontal brush is constantly controlled by a four level power sensor that accurately measures the vehicle and insures even pressure by the top brush throughout the wash cycle. Water and chemical are delivered through galvanized manifolds and chemical pumps insure the accurate dosage. Standard equipment includes manual activation, 18 meters of galvanized track, manual frost protection and a 4,60 meter wash height.

A3202 4.20m Wash Height Optional vehicle wash height.

A3205 3.5 m Wash Height

Optional vehicle wash height.

A3203 4.20 m Wash Height - Side Brushes Only System

Typically used for customers that require a faster wash cycle.

A3204 4.60 m Wash Height - Side Brushes Only System Typically used for customers that require a faster wash cycle.


WASH OPTIONS Y3305 Tanker Wash Brushes - Contoured

Contoured brushes designed to wash tankers.

PRE-WASH OPTIONS

Y3306 Rinse Aid Arch with Chemical Pump (option Y3311 recommended) Additional arch for rinse aid chemical.

Y3312 Additional Arch with Metering Pump - Pre-soak (requires option Y3311) Additional chemical arch with chemical pump. Can be used for wax, pre-wash, detergents, etc.

Y3310 Fixed Underchassis Wash with Pump (18.5 kW - 22 bar - 250 l/min) A set of two fixed high volume manifolds with nozzles directed at the under body of the vehicle.

Y3319 High Pressure Side Wash with Rotating Nozzles (11.2 kW, 70 bar, 80 l/min) Machine mounted, rotating nozzles designed to wash the wheels and lower portion of the trailer.

CABLE CARRIERS, GUIDE RAILS, EXTENSIONS

Y3303 Hot Dipped Galvanized Guide Rails 4m – per side Hot dipped galvanized rails to assist a driver in correctly aligning the vehicle in the wash bay.


Y3307 Caterpillar Cable Carrier with Five Posts Cable and hose support with caterpillar style carrier track and tray. Includes five galvanized posts. Deluxe system for outside or in bay utility support.

Y3308 Trolley Cable Carrier with Three Posts Cable and hose support for utilities, includes rail, cable carries and three galvanized posts.

Y3309

Stand for Cables and Hoses for 18m track length ONLY Single post to support cable and hoses.

Y3317 Trolley Cable Carrier with Wall Mounting Brackets Cable and hose support for utilities, includes rail, cable carries and wall brackets.

Y3314 Track and Cable Extensions (4 m) (mandatory with Y3315 and Y3321)

Extra 4m of track and utility lines to wash longer vehicles.

Y3315 Caterpillar Chain Extension (4 m) (requires option Y3314) ** Extra 4m caterpillar chain and tray required to wash longer vehicles.

Y3321 Trolley Cable Carrier extension (4 m) (requires option Y3314) ** Extra 4m trolley rail and rollers required to wash longer vehicles.


Y3351 Track and Cable Extensions (6 m) (mandatory with Y3315 and Y3321) Extra 6m of track and utility lines to wash longer vehicles.

SELF-SERVICE ACTIVATION Y3345 10 Program card reader with 30 cards per program, Traffic Lights, Guide

Rails and Self-Service Instruction Signs Card reader with stand and supply of cards, can be programmed for value or smart cards, red and green traffic lights mounted on machine and signage.

Y3347 Photo eye start with red and green traffic light

Set of photo eyes is mounted to the Atlas, which detects the vehicle. The traffic light indicates the vehicle is in the correct position.

Y6021 Additional program cards for card reader

Price per 100 cards.

Y1324 Manual Push Button Stand

1m post with mounting plate for manual push buttons. Y1374 Cover for Manual Push Button Stand

Locking cover for manual push buttons. Option to Y1324 Y3350 Safety Barriers and Signage

Safety fence around the car wash, except for entrance and exit, and safety signage. Ideally suited for a car wash not in a building that requires safety barriers

ACCESSORIES Y3316 Drive-thru Kit for Stationary System

Kit consists of traffic lights, track and guide rails necessary for drive-thru operation. See drive-thru explanation for description of operation.

Y3313 Automatic Frost Protection Thermostatic controlled system that purges the water system with air after the wash so the water lines will not freeze. This option is recommended in areas where the temperatures are frequently below freezing.


Y3343 Automatic Frost Protection for Chemicals and dosing pumps Two chemical containers and dosing pumps are heated and operate to approximate -5°C.

Y3301 Water Feeding Pump - 2.2 kW Boost pump for water supply.

Y3302 Splash Guards (for 4.60 m Wash Height) Vinyl side shields for side brushes. Prevents most water from splashing beyond the truck wash.

Y3341 Splash Guards (for 4.20 m Wash Height)

Vinyl side shields for side brushes. Prevents most water from splashing beyond the truck wash.

Y3342 Splash Guards (for 3.50 m Wash Height)

Vinyl side shields for side brushes. Prevents most water from splashing beyond the truck wash.


Y3320 Traffic Lights with Stand Red and green traffic lights that assist driver in locating the vehicle in the proper start position.

Y3340 Small Message Service (SMS)

Diagnostic alarms for emergency stop button, low pressure, overload and general emergency faults can be sent to mobile phones. SIM card is not included.

Y3311 Variable Frequency Drive (only one required) A variable frequency drive is added for multiple gantry speeds.

Y3318 Kit for Reclaim Operation Necessary manifolds to wash with reclaim water.

Y3340 Non-Standard Frame Colors Standard colors are red, yellow and blue. Other colors are optional.

Y3322 230 V - 60 Hz Operation (requires option Y3311)

Electrical components for 60 Hz operation.


ATLAS

Description of Operation

* The standard is a 2-way cycle.

* The machine mounted photo eyes assist the driver in placing the truck in the wash bay, the operator presses the start button, inserts a coin/token in the Coinbox or card.

* After a warning signal, the top brush lowers, the side brushes move to the centre and begin rotating.

* The brushes start moving over the surface of the truck, while water and shampoo are sprayed.

* At the back of the truck, after a pause, the truck wash stops, reverses rotation of brushes and moves towards the home position rinsing the vehicle.

* If the OPTIONAL wax or rinse aid is selected, it is applied during the rinse cycle.

* 7 Different programs can be selected (see program selections).


PROGRAMS DESCRIPTION

Wash programs are selected by push buttons, which are located on the remote control box. As a standard, the Atlas includes programs no. 1, 2, 3, & 4. PROGRAM No. 1 “Standard” For “single shape” vehicles such as buses, delivery trucks, etc. • After positioning the vehicle, operator presses the START button. • Top brush lowers and follows the profile of the vehicle. During the forward run, all the

brushes wash the vehicle surface and close when the back is reached. • When the forward run is finished, the brushes reverse and the unit moves to the home

position. • The top brush does not profile the vehicle while returning to the home position. PROGRAM No. 2 “Standard” For “light vehicles, cars, vans, etc.” (suggested for max. height less than 2,5 m.) The unit completes 1 cycle • The program is the same as no. 1. • For light vehicles this is the best program, since the pressure of the brush against the rear

of the vehicle is not excessive.


PROGRAM No. 3 “Standard” For trucks with second trailer or “pup” The unit completes 1 cycle. • Top brush acts like program 1, but amp senses during complete cycle. The space between

trailers is washed clean to a minimum height of 1,5 m. • Distance between trailers must be at least 120 cm.; otherwise, the brush can be

stopped between the trailers. PROGRAM No. 4 “Standard” For tractor with trailers • Similar to program 3, but the minimum height is different. PROGRAM No. 5 (not included as standard) For open back vehicles (flatbeds) The unit completes 3 cycles. • The top brush, after washing the tractor during the forward run, stays in the up position

while returning to the home position. The side brushes follow a normal cycle. PROGRAM No. 6 (not included as standard) High productivity The unit completes only a half cycle. • The Atlas stops at the end of the forward run waiting for another vehicle to wash in

opposite direction. • This reduces the wash time by 50%.


PROGRAM No. 7 (not included as standard) Tanker wash The unit completes 1 cycle. • The top brush, after washing the cabin, is lifted to the maximum height in order to avoid

touching the top of the tank. It lowers to wash the rear of the tank. • While traveling home, the top brush clears the rear of the tank and is then lifted to

maximum height. The side brushes perform usual operations during the cycle. • RYKO® can supply specially shaped side brushes to better wash tanks. • RYKO® can offer special programs to meet most customers requirements.

DRAWING


ATLAS

Chemicals Utilities

TOTAL WATER DETERGENT PRE-SOAK ELECTRICAL POWER

Liters ML ML kWh

Wash and Rinse

800

60

--

.68

Pre-soak, Wash and Rinse

820

60

40

.72

DOUBLE REAR WASH (Search Back)

When the rollover reaches the back of the truck during its forward run, the top brush lowers. The unit then stops and reverses the run until the top brush is against the rear of the truck. This allows the back surface to be washed, cleaning what is probably the dirtiest surface twice. • Programs 2, 5 and 7 do not perform searching back. The operator can choose to override the double rear wash during individual wash cycles or on all wash cycles.


Program 1 Forw ard Run

Program 1 Backw ard Run

ATLAS


TECHNICAL DATA

Vehicle Size: Max. vehicle height 3,50 / 4,20/ 4,60 m. Max. vehicle width 2,60 m. Max. vehicle length 18 m. Equipment dimensions: Height 4,50 / 5,20 / 5,60 m. Width 4,40 m. Length 2,20 m. Rails length 24 m. Width between rails (track gauge) 3,80 m. Weight maximum: 3,500 kg RPM of brushes: 115 RPM Machine speed: 7,7 m/min Side brush openning speed: 11,5 m/min Top brush lifting speed: 8,3 m/min Voltage supply: 208/320V AC, 3ph 60 Hz, 5,75kW+N+G

380/415V AC, 3ph 50 Hz, 5,5kW+N+G Low voltage : 24 V Cable section: 5 X 6 mm2

Power of driving motors: 0,36 kW X 2 Power of side brush rotation motors: 1,1 kW X 2 Power of side brush drive motors: 0,18 kW X 2 Power of top brush motor: 1,1 kW X 1 Power of top brush lifting motor: 0,36 kW X 1 Water supply: 3 bar, 200 lt./min Water inlet: R 1” X 2 Water pump (not included): 2,2 kW Approximate water consumption: 280 l/min


PREVENTIVE MAINTENANCE

DESCRIPTION FREQUENCY General cleaning of the unit daily Drain pipes to avoid freezing when necessary Check integrity of the cable on weekly the top brush lifting system Visual inspection of the electric monthly cables and pipes Lubricate chains monthly Lubricate knuckles (bearing supports) yearly Check brush wear monthly Check that rails are firmly tightened monthly Check that brushes are firmly tightened monthly Check top brush level monthly Clean nozzles monthly


DAILY CHECK-LIST BEFORE OPERATION

DESCRIPTION FREQUENCY Check that unit runs freely and smoothly on rails and that cables easily follow the machine’s movement during a wash cycle daily Check the emergency stop button daily Check that rails are clean daily Check that brushes are clean and free of foreign objects daily Extraordinary maintenance should be accomplished only by authorized technicians. To maintain the unit in top condition we recommend an inspection by a Ryko technician every six months.

ATLAS THREE BRUSH ROLLOVER

TRUCK WASH ORDER INFORMATION SHEET

ORDER DATE:

ORDERED BY:

DISTRIBUTOR ORDER #:

EQUIPMENT PURCHASER (send invoice to)

NAME:

ADDRESS:

CITY:

COUNTRY:

PHONE:

VAT NUMBER (CEE) ……………………..

EQUIPMENT TO BE INSTALLED AT:

NAME:

ADDRESS:

SHIPPING ADDRESS: (if different than purchaser’s

address)

NAME:

ADDRESS:

CITY:

COUNTRY:

REQUESTED SHIP DATE (ex-works)

FREIGHT:

PREPAID

COLLECT

OCEAN

TRUCK

AIR

or specify:

VOLTAGE AT LOCATION:

208/230 (60 Hz)

380/415 (50 Hz)

Other:

PAYMENT METHOD:

Prepaid

Bank Draft

Other:

BANK INFORMATION:

BANK NAME:

ATTN TO:

ADDRESS:

CITY:

COUNTRY:

PHONE:

ACCOUNT OF:

ACCOUNT NO:

MACHINE TO WORK WITH THE

FOLLOWING RYKO USA EQUIPMENT

(remember to also send order to Ryko USA):

REMARKS:

Atlas Order Form_online_October 07.doc Page 1 of 3



Quantity:

A3101 BASE UNIT WITH TOP & SIDE BRUSHES (4.60 m) A3202 BASE UNIT WITH TOP & SIDE BRUSHES (4.20 m) A3205 BASE UNIT WITH TOP & SIDE BRUSHES (3.50 m) A3203 BASE UNIT WITH SIDE BRUSHES ONLY(4.20 m) – NA A3204 BASE UNIT WITH SIDE BRUSHES ONLY (4.60 m) – NA

Base unit includes: Hot Dipped Galvanized and Painted Frame (standard color Blue Ral 5002), Manual activation by Keypad, Detergent Pump, Filament Washers, Hot Dipped Galvanized Tracks – 18 m long, Manual Frost Protection, Standard Supply: 380 / 415 V – 50 Hz. Metal Frame Color: Blue RAL 5002

Other (Y3340): Brush Colors: Positioning of Outlets: Right Left Front Wheel Drive at: Left Right (driving on left side of road)

Y3322 230 – 60 Hz Operation (requires option Y3311) Programming:

Special Programming* (Describe: ) * Extra cost quoted on request Wash Options:

Y3305 Tanker Wash Brushes – contoured Chemical Options:

Y3312 Additional Arch with Metering Pump – Pre-Soak (requires option Y3311) Y3311 Variable Frequency Drive (only 1 per truck wash system) (recommended with Y3306,

Y3312 and Y3344 – mandatory with Y3322) Pre-Wash Options:

Y3319 High Pressure Side Wash with rotating nozzles Y3310 Fixed Underchassis Wash with pump Y3306 Rinse Aid Arch with chemical pump (requires option Y3311) Y3344 High Impact Rinse Arch with pump (requires option Y3311)

Covers/Splashguards:

Y3302 Splash Guards (for 4.60 m wash height)




Y3341 Splash Guards (for 4.20 m wash height) Y3342 Splash Guards (for 3.50 m wash height) Y3347 Photoeye activation with Red/Green Traffic Light on Rollover Y3320 Traffic Lights with Stand

Cable Carriers, Guide Rails, Extensions:

Y3309 Stand for Cables and Hoses (maximum track length = 18m) Y3307 Caterpillar Cable Carrier with Five Posts – for 24 m. tracks Y3308 Trolley Cable Carrier with Posts – for 24 m. tracks Y3356 Trolley Cable Carrier with Posts – for 18 m. tracks Y3317 Trolley Cable Carrier with Wall Mounting Brackets – for 24 m. tracks Y3314 Track & Cable Extensions (4 m) Y3351 Track & Cable Extensions (6 m) Y3315 Caterpillar Chain Extension (4 m) (requires option Y3314) Y3321 Trolley Cable Carrier extension (4 m) (requires option Y3314) Y3303 Hot Dipped Galvanized Guide Rails (2 x 4 m) Qty:

Self-Serve Activation:

Y3345 Self Service Kit including 10 program Card Reader (30 cards per program), Traffic Lights, Guide Rails, Self-Service Signage

Y6021 Additional Program Cards for Y3345 - Qty: (sold in quantities of 100) Y1324 Manual Push Button Stand Y1374 Cabinet for Manual Push Button (to be installed on wall or on stand Y1495) Y1495 Floor Stand for Manual Activation Cabinet (requires Y1374) Y3350 Safety Barriers and Signs

Accessories:

Y3316 Drive-Thru Kit for Stationary System Y3313 Automatic Frost Protection (does not include the air compressor) Y3343 Automatic Frost Protection for Chemicals/Dosing Pumps Y3301 Water Feeding Pump, 2.2 kW

Y3349 Small Message Service (SMS) – Diagnostic Alarm Y3318 Kit to accept reclaim water system Y3352 Rear-view mirrors program

Remarks:


utilaj spalare camioane

Documents

wash height atlas manual

meter wash height

wash height optional

faster wash cycle

y3310 fixed underchassis

manual activation

atlas features

appearance manual