using the avanti tabletop centrifuge
DESCRIPTION
Using the Avanti Tabletop Centrifuge. As demonstrated by Joe Toney. Turn on the power switch. Select the proper rotor for your tubes. Remove from cover. Make sure spacers are inserted *. Little Red Spacers. * F2402 Rotor only. Seat rotor on drive shaft. Shaft. - PowerPoint PPT PresentationTRANSCRIPT
Using the Avanti Using the Avanti Tabletop CentrifugeTabletop Centrifuge
As demonstrated by Joe ToneyAs demonstrated by Joe Toney
Turn on the power switchTurn on the power switch
Select the proper rotor for your Select the proper rotor for your tubestubes
Remove from coverRemove from cover
Make sure spacers are insertedMake sure spacers are inserted**
*F2402 Rotor only
Little Red Spacers
Seat rotor on drive shaftSeat rotor on drive shaft
Shaft
Secure rotor to shaft with boltSecure rotor to shaft with bolt
Bolt
Tighten bolt with rotor wrenchTighten bolt with rotor wrench
Place your tubes in the rotorPlace your tubes in the rotor
Tubes of equal mass opposite one another
Hinges up
Don’t forget the lid!Don’t forget the lid!
Hand tighten
Make sure the door is seated Make sure the door is seated properly*properly*
The door open light will be lit (green) when door is properly closed.
The machine won’t run if it is not.
The sound you hear is the refrigeration turning on.
The control panelThe control panel
Open Door Light
Start Button
Rotor and speed read out and controls
Time Temperature
Select rotorSelect rotor Press rotor button, Press rotor button,
current rotor will be current rotor will be displayeddisplayed
Use up and down Use up and down arrow keys to scroll arrow keys to scroll through choicesthrough choices
Small rotor is F2402 Small rotor is F2402 (holds 24 Two ml (holds 24 Two ml tubes)tubes)
Press enter key to Press enter key to selectselect
Change settings by selecting the parameter, Change settings by selecting the parameter, scrolling, and then press enterscrolling, and then press enter
Up and Down Scroll Keys
Set Value with Enter Button
Speed can be set according to Speed can be set according to RPMRPM
Machine displays Speed in RPM
Speed Light is lit
Or by Or by rrelative elative ccentrifugal entrifugal fforce orce (RCF, x (RCF, x gg))
Joe selects RCF button
Value flashesValue flashes Value can be Value can be
adjusted by scrolling adjusted by scrolling up or downup or down
Value is set by Value is set by pressing enter pressing enter buttonbutton
Other adjustmentsOther adjustments Time – set desired time in minutesTime – set desired time in minutes Temperature – this should be set at 4 Temperature – this should be set at 4
ooCC Accel(eration) / Decel(eration) – no Accel(eration) / Decel(eration) – no
need to adjust unless special need to adjust unless special conditions conditions
Press start when you are ready to go!Press start when you are ready to go!
The speed read out will The speed read out will display zero, then display zero, then increase to set levelincrease to set level
Any problems will Any problems will develop before about develop before about 2000 rpm2000 rpm
If there is a problem, it If there is a problem, it will shut down and give will shut down and give an error messagean error message
The most common The most common problem is the DOOR problem is the DOOR OPEN light!OPEN light!
When the run has stopped (0 minutes, When the run has stopped (0 minutes, 0 rpm) press the open door button0 rpm) press the open door button
The lid will openThe lid will open
Remove your samples and follow Remove your samples and follow the house rulesthe house rules
“Turn the power off”
Take that rotor outTake that rotor out
Put it back in its homePut it back in its home
And Joe is all done, ….And Joe is all done, ….or is he?or is he?
C0650 Rotor for 50 ml conical tubes