using for the first time operation drying changing the
TRANSCRIPT
Using for the first time Operation Drying Changing the programme sequence Fragrance flacon
M.-
Nr.
11 6
63 4
9000FragranceDos – the dryer has two
positions for inserting a fragrance flacon. Use one or both whenever you want to add a pleasant fragrance to your laundry.
Close the unused socket.
Before using a fragrance flacon, please read "Warning and Safety instructions - Using a fragrance flacon (optional accessory)" and "Fragrance flacon" in the operating instructions.
Inserting a fragrance flacon1. 2.
3. 4.
Markers and must line up with each other.
5. 6.
ĺ Turn the outer ring clockwise a little.
Markers und must line up with each other.
Before drying ĺ Turn the outer
ring clockwise a little.
The further you open the flacon, the more intense the fragrance.
After dryingTo avoid the fragrance escaping needlessly:
ĺ Turn the outer ring anti-clock-wise until marker is in position .
When not in use, you can store the fragrance flacon in its original packag-ing.
Before cleaning the fluff filters ĺ Remove the
fragrance flacon.
ĺ Only store the fragrance flacon in its original packaging.
Never lay the fragrance flacon down. Otherwise, the fragrance will leak out.
TWJ6
60W
Pen
- A
U, N
Z
ɑ Before using the tumble dryer for the first time, ensure that it is correctly installed and connected. Please read the separate operating instructions supplied with the appliance.
ɑ Damage caused by switching the appliance on too soon. This can damage the heat pump. After setting up the tumble dryer, wait for at least one hour before starting a drying programme.
Energy saving tips
To avoid unnecessarily long drying times and high consumption of energy: – Spin the laundry at the maximum spin speed in the washing machine.
– Clean the fluff filters in the door and in the door opening after every drying cycle.
– Load according to the optimum amount of laundry recommended for the programme being used. This will mean that the energy consumption for the amount of laundry is at its most economical.
– Make sure the room temperature is not too high. If there are other heat producing appliances in the room in which the tumble dryer is located, make sure the room is well-ventilated and switch the other appliances off, if possible.
1. Notes on correct laundry care ɑ Ensure that any foreign objects (e.g. detergent
dispensing balls, lighters, etc.) have been removed from the laundry. Such items could melt or explode and cause damage to the dryer or the laundry.
ĺ Sort the laundry according to the type of fibre and weave, size, garment care label symbol and the drying level required.
ĺ Check seams and stitching to ensure that padding and linings are intact.
ĺ Fasten duvet covers and pillow cases to prevent small items from being rolled up inside them.
ĺ Fasten hooks and eyes. ĺ Tie together textile belts and apron ties. ĺ Sew in or remove loosened underwiring from bras.
OP
ER
ATIO
N
DR
YIN
G
CH
AN
GIN
G T
HE
PR
OG
RA
MM
E S
EQ
UE
NC
E
Switching on the tumble dryer ĺ Turn the programme selector to a programme.
The welcome tone will sound and the welcome screen will light up. The display will guide you through the initial commissioning process, which is divided into several steps.For further information, please refer to the separate operating instructions.
Emptying the condensed water container
Empty the condensed water container after every drying programme.
Empty container See will light up in the display if the maximum level of the condensed water container is reached.To turn the message off: Open and close the door while the dryer is switched on.
ĺ Pull out the con-densed water container.
ĺ To prevent water running out, keep it in a horizontal position when carrying it. Hold it at the front and at the back.
ĺ Empty the condensed water container.
ĺ Replace the container in the dryer.
ɑ Do not drink condensed water. It can cause health problems in people and animals.
Adding or removing laundryYou have forgotten an item of laundry, but the programme has already started. ĺ Touch the Start/Add laundry sensor.
Door can be opened lights up in the display.* ĺ Open the door. ĺ Add or remove laundry. ĺ Close the door. ĺ Touch the Start/Add laundry sensor.
The programme will start.* Exceptions:In some cases, e.g. during the cooling phase or in the Proofing programme, you cannot add laundry.
Cancelling a programme while it is running and selecting a new programmeIt is no longer possible to change the selected programme. This prevents the appliance being operated unintentionally, e.g. by children.If you adjust the programme selector, Cannot be changed will light up in the display. This indicator goes out when you select the original programme again. ĺ Turn the programme selector to the position.
The programme is cancelled. ĺ Select a programme. ĺ Touch the Start/Add laundry sensor.
1 Control panel The control panel consists of a display and various sensor controls.
2 Display Different values are displayed and/or selected in the display.
3 sensors The values in the display can be changed with the sensors.
4 OK sensor The OK sensor is used to confirm selected values
5 Perfect Dry indicator With programmes with a selectable drying level, the Perfect Dry system calculates the residual moisture present in the laundry to ensure the best drying result. The display flashes at the beginning of the programme and lights up towards the end of the programme.
6 Optical interface For service technicians.
7 Sensor controls for Extras You can supplement the drying programmes with Extras.
8 sensor You can use the sensor to call up an energy consumption forecast for the selected drying programme.
9 sensor The sensor starts the Delay start function.
10 Start/Add laundry sensor Touching the Start/Add laundry sensor starts the selected programme. The current programme can be interrupted to add laundry. The sensor flashes slowly as soon as it is possible for a programme to be started and then lights up constantly after the programme has started.
11 Programme selector For selecting programmes and switching the washing machine off. The dryer is switched on by selecting a programme, and switched off by turning the programme selector to the position. Under Further programmes/ you will find the Wash2Dry function as well as additional programmes and the option to change Settings.
Operating the sensorsThe sensors react to fingertip contact. Selection is possible as long as the respective sensor is illuminated.If a sensor is brightly lit this means: currently selectedIf a sensor is dimly lit this means: selection possible
2. Selecting a programme ĺ Turn the programme selector to a programme.
The interior drum lighting will come on.
Programme selectionThere are 3 possible ways to select a programme:1. Selecting standard programmes via the programme selector ĺ Turn the programme selector to the required programme. The selected programme will appear in the display. This will then be replaced by the standard display.
2. Selecting further programmes via the "Further programmes/" setting and the display: ĺ Turn the programme selector to the Further programmes/ position. Touch the sensors until the programme you want appears in the display.
ĺ Confirm the programme with the OK sensor.Selecting the Wash2Dry functionOnce the washing machine programme has completely finished, the drying programme tailored to the laundry will be displayed. ĺ Once the wash programme has ended, place the clean laundry in the tumble dryer and close the door.
ĺ To start the programme, all you need to do is press the Start/Add laundry sensor on the tumble dryer.
3. Selecting programmes via the MobileStart function and the Miele@mobile App ĺ Turn the programme selector to the MobileStart position. ĺ Follow the instructions in the display. ĺ Touch the Start/Add laundry sensor.
The dryer can now be operated via a mobile device together with the Miele@mobile App.
4. Selecting programme settings
Programmes with drying levelsCottons, Minimum iron, Delicates, Pre-ironing, Shirts, Express, Denim, Outerwear, Sportswear, Bed linen, Automatic plusThe preset drying level for the programme can be changed. ĺ Touch the or sensors to change the drying level.
Timed drying programmes and other programmesWarm air, Cool air, Basket programme, DryFreshYou can change the duration in 10-minute increments. ĺ Touch the or sensors to change the duration.
Cottons , Woollens handcare, Pillows, Proofing, Silks handcareThe drying result is preset by the dryer and cannot be altered.
Selecting Extras ĺ Touch the sensor for the Extra you want. It then lights up brightly.
Freshen upFor removing or reducing odours in clean (dry or damp) clothing.Gentle tumbleLow temperature drying for delicate fabrics with the symbol on the care label, e.g. acrylic garments.Anti-creaseThis helps prevent creasing if the laundry is not removed immediately after the end of the programme.BuzzerAcoustic signal at the end of a programme.
EcoFeedbackYou can use the sensor to call up an energy consumption forecast for the selected drying programme. ĺ Touch the sensor.
The estimated energy consumption will be displayed as a bar chart.
Delay start/SmartStartDelay startWith Delay start you can delay the start of a programme. The start of the programme can be delayed from 15 minutes up to a maximum of 24 hours.SmartStartThe SmartStart function (only functional in selected countries) lets you define a period of time during which your washing machine will start automatically. The dryer will start on receipt of a signal, e.g. from your energy supplier, that indicates that the electricity rate is particularly economical.
5. Starting the programme ĺ Touch the flashing Start/Add laundry sensor.
The Start/Add laundry sensor lights up.
1 Condensed water container – empty after every drying programme
2 Door3 Control panel4 Access panel for the heat exchanger and plinth filter
– Do not open during drying5 Cool air intake grille
– Do not obstruct with a laundry basket or other objects
3. Loading the tumble dryer ĺ Open the door.
ĺ Unfold the laundry and load loosely into the drum.
ɑ Do not overload the drum. Overloading can cause unnecessary wear and tear of the laundry, give a disappointing drying result and cause more creasing.
ɑ If you are not using a fragrance flacon: the tabs must be pushed down completely (see arrows) to ensure both sockets are closed.
ɑ When closing the door, make sure that laundry does not get trapped in the door opening. ĺ Shut the door with a gentle
swing.
6. End of programme - unloading the drum
The programme is finished when Finish/Anti-crease or Finish appears in the display. The Start/Add laundry sensor light goes out. – To save energy, 10 minutes after the end of the programme the Start/Add laundry sensor will begin to flash slowly and the display will go out.
– The tumble dryer switches off automatically.
ɑ Do not open the door before the end of the programme.
ĺ Open the door. ĺ Remove the laundry.
ɑ Check that all items have been removed from the drum. If items are left in the dryer, they could be damaged by overdrying when the dryer is used the next time.
If the dryer is switched on at the mains and the door is opened, the drum lighting will come on. It will go out after a few minutes to save energy. ĺ Turn the programme selector to . ĺ Clean the fluff filters. ĺ Close the drum door. ĺ Empty the condensed water container.
Adding laundryYou can add laundry. ĺ Follow the instructions in "Changing the programme sequence".
en - AU, NZ M.-Nr. 11 663 490
Quick Start GuideHeat pump tumble dryer
These short instructions are not a substitute for the operating instructions supplied with the appliance. Please read the operating instructions supplied with your tumble dryer before using it for the first time.Take note of the Warning and Safety instructions, as well as the full descriptions on how to use your appliance.
Cleaning and care Problem solving guide
Fluff filters
Removing visible fluff
Clean the fluff filters in the door opening after every drying cycle.
Remove the fragrance flacon (if fitted).
ĺ Pull the upper fluff filter forwards to remove it.
ĺ Use your fingers or a vacuum cleaner to remove the fluff from the surface of the filter.
ĺ Push the upper fluff filter back in until it clicks into position.
ĺ Close the door.
Cleaning the fluff filters and air flow openings thoroughly
If the drying duration has become longer or the surface of the filters is visibly compacted with fluff, you should carry out the following cleaning procedure.
ĺ Pull the upper fluff filter forward to remove it.
ĺ Turn the yellow dial on the lower fluff filter in the direction of the arrow (until you hear it click).
ĺ Hold the dial and pull the fluff fil-ter forwards to remove it.
ĺ Use a vacuum cleaner with a long crevice noz-zle attached to remove any visi-ble fluff from the upper air flow openings.
ĺ Flush the fluff filters through with warm running water.
ĺ Shake the fluff filters thoroughly and then dry them carefully.
Ensure the filters are dry before replacing them. Wet filters could cause operational faults.
ĺ Refit all of the fluff filters and close the door.
CLE
AN
ING
AN
D C
AR
E
PR
OB
LEM
SO
LVIN
G G
UID
E
Programme overview
PR
OG
RA
MM
E C
HA
RT
Gar
men
t ca
re la
bel
sym
bo
lsD
ryin
g
norm
al /
high
er te
mpe
ratu
re
R
educ
ed te
mpe
ratu
re: s
elec
t G
entle
tum
ble
(for
delic
ate
fabr
ics)
.
D
o no
t tum
ble
dry
Iro
ning
ve
ry h
ot
ho
t
w
arm
D
o no
t iro
n
Tip
s o
n d
ryin
g –A
lway
s ob
serv
e th
e m
axim
um re
com
men
ded
load
s gi
ven
in
the
Pro
gram
me
char
t.
Ove
rload
ing
can
caus
e un
nece
ssar
y w
ear
and
tear
to th
e la
undr
y. It
can
giv
e a
disa
ppoi
ntin
g dr
ying
resu
lt an
d ca
use
mor
e cr
easi
ng.
–D
o no
t loa
d th
e dr
um w
ith it
ems
that
are
stil
l soa
king
wet
. M
ake
sure
you
r la
undr
y is
spu
n at
the
max
imum
spi
n sp
eed
in
the
was
hing
mac
hine
bef
ore
dryi
ng.
–M
inim
um ir
on fa
bric
tend
s to
cre
ase
mor
e, th
e la
rger
the
load
. Th
is is
par
ticul
arly
the
case
for
garm
ents
mad
e fro
m v
ery
fine
wea
ve fa
bric
, suc
h as
shi
rts
or b
lous
es.
Plinth filterClean the plinth filter when Clean the plinth filter. See lights up.
To delete the message: confirm with OK. ĺ Press the round,
indented area on the heat exchan-ger access panel to open it. The panel will spring open.
ĺ Pull the plinth filter out by the handle.
Removing the plinth filter will cause a guide pin in the dryer to come out. This pin ensu-res that the heat exchanger access panel can only be closed if the plinth filter is fitted.
ĺ Pull the handle out of the plinth filter.
ĺ Clean the filter thoroughly under running water.
ĺ Squeeze the water out of the plinth filter thoroughly.
ɑ The plinth filter must not be replaced dripping wet.
ĺ Use a damp cloth to remove any fluff from the access panel.
Refitting the plinth filter ĺ Fit the filter back
on the handle the right way.
ĺ Insert the handle with the plinth fil-ter attached over the two guide pins.
The word Miele on the handle must be the correct way up.
ĺ Close the heat exchanger access panel.
Pro
gram
me
Lo
ad
(wei
ght o
f dry
la
undr
y)
Item
s
Extra dry
Normal plus
Normal
Slightly dry
Hand iron
Hand iron
Machine iron
Extra
s
Co
tto
ns
9 kg
Cot
ton
item
s su
ch a
s th
ose
desc
ribed
und
er C
otto
ns N
orm
al
with
nor
mal
resi
dual
moi
stur
e.X
,
Co
tto
ns9
kgTo
wel
ling,
jers
ey w
ear,
T-sh
irts,
und
erw
ear,
baby
clo
thes
, w
orkw
ear,
cove
rs, j
acke
ts, b
athr
obes
, and
flan
nele
tte b
ed li
nen
War
ning
: Do
not u
se E
xtra
dry
for j
erse
y fa
bric
s (e
.g. T
-shi
rts,
un
derw
ear,
baby
clo
thes
), as
they
hav
e a
tend
ency
to s
hrin
k
XX
XX
XX
X
, ,
,
Min
imum
iro
n4
kgW
orkw
ear,
over
alls
, pul
love
rs, d
ress
es, t
rous
ers,
legg
ings
and
ta
ble
linen
.–
XX
XX
X–
,
, ,
Del
icat
es2.
5 kg
Shi
rts,
blo
uses
, lin
gerie
, app
liqué
d ga
rmen
ts.
–X
XX
XX
–
, ,
Wo
olle
ns h
and
-ca
re2
kgP
ullo
vers
, car
diga
ns, s
ocks
, sto
ckin
gs.
––
––
––
–
Shi
rts
2 kg
Shi
rts
and
blou
ses.
–X
XX
XX
–
, ,
,
Mo
bile
Sta
rt
The
Mie
le@
mob
ile A
pp is
use
d fo
r sel
ectin
g pr
ogra
mm
es a
nd o
pera
ting
the
mac
hine
.
Den
im3
kgJe
ans,
jack
ets,
ski
rts,
shi
rts.
–X
XX
XX
–
, ,
, B
ed li
nen
4 kg
Bed
line
n, p
illow
cas
es.
XX
XX
XX
X
, P
roo
fing
2.5
kgM
icro
fibre
fabr
ic, s
kiw
ear,
oute
rwea
r, fin
e cl
ose
wea
ve c
otto
n ga
rmen
ts (p
oplin
), ta
blec
loth
s.Fi
re h
azar
d! D
o n
ot
use
pro
ofin
g a
gen
ts c
ont
aini
ng
par
affin
.
––
X–
––
–
,
Pre
-iro
ning
1 kg
Cot
ton
trous
ers,
ano
raks
, shi
rts.
––
X–
X–
–
, ,
Was
h2D
ryTh
e pr
ogra
mm
e is
sel
ecte
d au
tom
atic
ally
in c
onju
nctio
n w
ith th
e pr
ogra
mm
e se
lect
ion
on th
e co
nnec
ted
was
hing
mac
hine
.
War
m a
ir8
kgTh
ick
and
mul
ti-la
yere
d ja
cket
s, p
illow
s, s
leep
ing
bags
, bla
nket
s.–
––
––
––
,
, O
uter
wea
r2.
5 kg
Out
erw
ear w
hich
is s
uita
ble
for d
ryin
g in
a tu
mbl
e dr
yer.
––
X–
X–
–
, ,
Exp
ress
4 kg
Gar
men
ts s
uita
ble
for t
he C
otto
ns p
rogr
amm
e.X
XX
XX
XX
,
Sp
ort
swea
r3
kgS
port
swea
r whi
ch is
sui
tabl
e fo
r dry
ing
in a
tum
ble
drye
r.–
XX
XX
X–
,
Aut
om
atic
plu
s5
kgM
ixed
load
s of
gar
men
ts s
uita
ble
for t
he C
otto
ns a
nd M
inim
um
iron
prog
ram
mes
.–
XX
XX
X–
,
Pill
ow
s–
Pillo
ws
(2 s
mal
l 40
x 80
or 1
larg
e 80
x 8
0)
––
X–
––
–
, C
oo
l air
8 kg
Any
gar
men
ts w
hich
nee
d to
be
aera
ted.
––
––
––
–
, B
aske
t p
rog
ram
me
3.5
kg
max
. bas
ket
load
Bag
s, s
hoes
, sof
t toy
s, b
eani
es, s
carv
es, g
love
s, s
equi
ned
tops
Onl
y to
be
used
with
dry
ing
bas
ket
(op
tiona
l acc
esso
ry).
––
––
––
–
Silk
s ha
ndca
re1
kgB
lous
es, s
hirt
s–
––
––
––
,
Dry
Fres
h9
kgYo
u ca
n re
duce
or e
limin
ate
unw
ante
d od
ours
in c
lean
, dry
te
xtile
s.U
se th
is p
rogr
amm
e in
con
junc
tion
with
the
Dry
Fres
h fla
con.
––
––
––
–
,
=
Fre
shen
up;
=
Gen
tle tu
mbl
e;
= A
nti-c
reas
e;
= B
uzze
rX
= Ye
s, –
= N
o
Some of the messages in the display are more than one line long. Touch the or sensor to read them in full.
Problem/Fault message Possible cause and remedy
000 lights up after the tumble dryer is switched on and a programme cannot be selected
Access via a code has been activated.You must enter the correct code to use the tumble dryer. See "Settings - Code" in the operating instructions.
After a programme termination: Empty container See
The condensed water container is full or there is a kink in the drain hose. ĺ Empty the condensed water container. ĺ Check the drain hose.
To switch off the message: ĺ Open and close the door while the dryer is switched on.
After the end of the programme:
Clean the plinth filter. See
There is a build-up of fluff. See "Cleaning and care" in the operating instructions. ĺ Clean the fluff filters. ĺ Clean the plinth filter.
To switch off the message: ĺ Confirm with OK.
After a programme termination:
Clean the plinth filter. See
There is a blockage due to fluff. See "Cleaning and care" in the operating instructions. ĺ Clean the fluff filters. ĺ Clean the plinth filter. ĺ Clean the area underneath the air flow openings. ĺ Clean the heat exchanger.
To switch off the message: ĺ Switch the dryer off and back on.
Finish/Cooling down The programme has finished but the laundry has not yet cooled down. ĺ Either remove the laundry and spread it out to cool down or leave it in the tumble dryer to cool down during the cooling phase.
Problem/Fault message Possible cause and remedy
The display is in a dif-ferent language
A different language has been selected in "Settings - Language ". ĺ Set the language you want. The flag symbol serves as a guide.
The display remains dark and the Start/Add laundry sensor does not light up or flash
There is no power to the tumble dryer. ĺ Check whether the mains plug is plugged in and switched on.
ĺ Check whether the circuit breaker has tripped.The tumble dryer has switched off automatically to save energy. ĺ Turn the programme selector to switch the tumble dryer back on again.
The laundry is not suffi-ciently dry
The load consisted of different types of fabric. ĺ Finish drying using the Warm air timed drying programme. ĺ Select a more suitable programme next time.
Tip: You can alter the residual moisture level for some programmes. See "Settings menu - Drying levels" in the operating instructions.
Items made of synthetic fibres are charged with static electricity after drying
Synthetic fibres tend to attract static charge.Static charge can be reduced by adding fabric softener to the final rinse in the washing programme.
There is a build-up of fluff
Fluff is principally the result of friction when garments are being worn and to some extent when they are being washed. Machine drying hardly causes any fluff to form.Fluff is collected by the fluff filters and the plinth filter and can be removed easily.See "Cleaning and care".
There are humming noises
This is not a fault. These noises are normal and caused by the operation of the compressor (heat pump)..