T0759 1

STRAW CHOPPER NEW HOLLAND TX66-68

USER´S MANUAL &SPARE PART LIST

Rekordverken Sweden ABÖttum

535 92 KVÄNUMTel. +46-511-303 00 Fax. +46-511-303 01

2006-04-20

2

3

INDEX

Chapter Page

Adjusting chopping quality 4

Adjusting chopper vanes 5

Straw Chopper Assy 6-7

Straw Chopper with fan Assy 8-9

Mechanical Tailboard Assy 10-11

Electric Tailboard Assy 12-13

4

Adjusting chopping quality

CAUTION: Shut off engine, set parking brake and remove key

The chopper can chop many differentcrops. Counter blade and space bar shall beadjusted depending on crop and chopping result. How the chopper is adjusted affect how long the straw will be and how much power the chopper consume. Here follows some recommendations how to adjust the chopper in different crops.

Cereals:Wheat, rye, barley and oat. Space bar ought to be installed. Counter blade bar can be in position 1, 2 or 3 depending on how short the chopped straw will be and how wet the straw is. Position 1, take most power and if the straw is moisture, there is a risk that material starts to build up on the counter blade and power consumption will increase. If straw builds up one ought to set counter blade bar to a less aggressive position. It is more important to use space bar then to set the counter blade in a more aggressive position. Space bar consumes less power compared with adjusting counter blade from position 2 to 1. If you priority good chopping result will the chopper consume more power which can effect the combines capacity. It is very important to adjust the chopper correct considering to chopping result and combines capacity.

Rape:If the crop is heavy, space bar ought to be not installed. Counter blade bar ought to be in position 4. A less aggressive position of counter blade helps the material come into the chopper.

Space bar

Position 1

Position 5

5

Adjusting chopper vanesSpreader hood is set from factory to receive an even spread pattern.Adjustments can be made by turning crank lever and also by moving vanes individually at front and rear position

Deflectors can be adjusted for minimum and maximum spread with crank lever. Picture shows maximum spread

Picture showsminimum spread.

Picture show indicator whenvanes are in normal position

If the wind is blowing from the side, set chopper vanes against the wind to prevent the standing crop from becoming covered with chopped material.Chopper vanes are adjusted centrally by means of electric motor. The adjustment is made from the operator’s cab.Picture shows maximum spread to the left and reduced to the right.

Chopper vanes can also be adjustedup and down.Normal position is in the middleof the 3 holes.

Crank lever

Indicator

6

Straw Chopper Assy

7

Pos Qty Description Dimension Part.no Notes1 2 Bearing house 005962 1 Bracket 474173 2 Bushing 3.5 413504 1 Chopper housing 130285 1 Counter knife bar 350756 1 Cover ECY211 029617 2 Decal 027698 1 Decal 028069 1 Hook 4743210 1 Hook 4741911 2 Knob nut 0205712 4 Lock nut M8 0955813 2 Lock nut M10 0956714 3 Lock washer 12.2x21.1x2.5 0082315 8 Lock washer 16.2x27.4x3.5 0081516 8 Lock washer 8.1x14.8x2 0081117 1 Machine sign 0241518 1 P-rotor cpl 1303119 1 Plate 3507020 2 Pop rivet 4.8x14 0208521 2 Screw M10x30 0921822 1 Screw M12x30 0924523 8 Screw M16x45 0972924 5 Screw M8x16 0920825 7 Screw M8x20 0920926 2 Shield 4684727 1 Key 0073328 2 Stop 4614529 2 Washer 10.5x26x2.0 0083030 2 Washer 13x38x3.0 0082831 10 Washer 17.5X34x3.0 0080432 14 Washer 8,4x22x2 0082933 1 Wear cross bar 3507634 1 Locking plate 3507135 69 Counter knife 4015136 54 Lock nut M10 958237 108 Bushing 4400138 108 Flail knife 3377039 108 Spacer 4134940 54 Screw M10x50 0933041 2 Bearing 00597

8

Straw Chopper with fan Assy

9

Pos Qty Description Dimension Part.no Notes1 2 Bearing house 005962 1 Bracket 474173 2 Bracket 474204 2 Bushing 3.5 413505 1 Chopper housing 130286 1 Counter knife bar 350757 2 Decal 027698 1 Decal 028069 1 Fan wheel 2303910 1 Fan wheel 2305011 1 Fan housing 1304512 1 Fan housing 1304613 2 Bracket 3507715 1 Hook 4743216 1 Hook 4741917 1 Channel 2347018 1 Channel 2347119 2 Key 0072420 2 Knob nut 0205721 2 Cover 2347222 31 Lock nut M8 0955823 2 Lock nut M10 0956724 6 Lock nut M6 beeloc 0956925 2 Lock washer 10.2x18.1 0081326 3 Lock washer 12.2x21.1x2.5 0082327 8 Lock washer 16.2x27.4x3.5 0081528 34 Lock washer 8.1x14.8x2 0081129 2 Lock washer 30x5 4716330 1 Machine sign 0241531 1 Rotor cpl 1302732 1 Plate 3507033 2 Pop rivet 4.8x14 0208534 2 Screw M10x25 0921735 2 Screw M10x30 0921836 1 Screw M12x30 0924537 8 Screw M16x45 0972938 6 Screw M6x16 0920339 29 Screw M8x16 0920840 36 Screw M8x20 0920941 2 Shield 4684742 1 Key 0073343 2 Stop 4614544 2 Washer 10.5x26x2.0 0083045 2 Washer 13x38x3.0 0082846 10 Washer 17.5X34x3.0 0080447 12 Washer 7.0x16 0080048 94 Washer 8,4x22x2 0082949 1 Wear cross bar 3507650 1 Locking plate 3507151 69 Counter knife 4015152 54 Lock nut M10 0958253 108 Bushing 4400154 108 Flail knife 3377055 108 Spacer 4134956 54 Screw M10x50 0933057 2 Bearing 00597

10

Mechanical Tailboard Assy

11

Without fan With fan1 2 2 Adjustment weld 348282 2 2 Ball M12 021183 2 2 Composite bushing 023094 - 1 Deflector 2 LH 348374 1 - Deflector 1 LH 348385 - 1 Deflector 2 RH 348335 1 - Deflector 1 RH 348346 - 1 Deflector 3 LH 348366 1 - Deflector 2 LH 348377 - 1 Deflector 3 RH 348327 1 - Deflector 2 RH 348338 - 1 Deflector 3,5 LH 350258 1 - Deflector 3 LH 348369 - 1 Deflector 3,5 RH 350269 1 - Deflector 3 RH 3483210 1 1 Deflector 4 LH 3483511 1 1 Deflector 4 RH 3483112 1 1 Deflector 5 LH 3489213 1 1 Deflector 5 RH 3489314 2 2 Gas spring 0240815 1 1 Grip clip 0047217 16 16 Lock nut M8 0955818 6 6 Lock washer 8.1x14.8x2 0081119 1 1 Locking plate 3508020 1 1 Locking plate 3508121 2 2 Locknut 0958322 1 1 Lockrod ø12 3508423 4 4 Nut M12 0953324 2 2 Nut weld 4733325 1 1 Rail LH 2347526 1 1 Rail RH 2347427 2 2 Screw M12x30 0924528 8 8 Screw M8x20 0920929 10 10 Screw M8x25 0921030 10 10 Spacer Ø35 4739431 1 1 Tailboard 1304732 2 2 Washer 12.5x26x2 0082633 20 20 Washer 8,4x22x2 0082934 10 10 Washer 9x35x2 0084935 - 1 Tailboard cpl 1303835 1 - Tailboard cpl 13040

NotesPos DescriptionQty Dimension Part.no

12

Electric Tailboard Assy

13

Wihout fan With fan1 1 1 Adjustment 348822 1 1 Ball M12 021183 1 1 Bushing 17x2,0 348814 1 1 Bushing ø35 345195 1 1 Circlip SGA 20 006166 2 2 Composite bushing 023097 1 1 Decal vanes 023498 - 1 Deflector 2 LH 348378 1 - Deflector 1 LH 348389 - 1 Deflector 2 RH 348339 1 - Deflector 1 RH 3483410 - 1 Deflector 3 LH 3483610 1 - Deflector 2 LH 3483711 - 1 Deflector 3 RH 3483211 1 - Deflector 2 RH 3483312 - 1 Deflector 3,5 LH 3502512 1 - Deflector 3 LH 3483613 - 1 Deflector 3,5 RH 3502613 1 - Deflector 3 RH 3483214 1 1 Deflector 4 LH 3483515 1 1 Deflector 4 RH 3483116 1 1 Deflector 5 LH 3489217 1 1 Deflector 5 RH 3489318 2 2 Gas spring 0240819 1 1 Grip clip 0047221 1 1 Link welded 3508522 15 15 Lock nut M8 0955823 2 2 Lock nut M12 0956824 1 1 Lock nut M6 beeloc 0956925 6 6 Lock washer 8.1x14.8x2 0081126 1 1 Locking plate 3508027 1 1 Locking plate 3508128 1 1 Locknut 0958329 1 1 Lockrod ø12 3508430 2 2 Nut M4 0953831 1 1 Rail 2347532 1 1 Rail 2347433 1 1 Rod welded 3481934 2 2 Screw M10x60 0946735 1 1 Screw M12x30 0924536 2 2 Screw M12x60 0922737 6 6 Screw M8x20 0920938 10 10 Screw M8x25 0921039 1 1 Screw M8x40 0927340 1 1 Spacer Ø15 4734941 10 10 Spacer Ø35 4739442 1 1 Spacer ø12 4734843 1 1 Tailboard 1304744 4 4 Washer 12.5x26x2 0082645 1 1 Washer 7x35x3 0086046 17 17 Washer 8,4x22x2 0082947 1 1 Washer 8.4x26x5 0085848 10 10 Washer 9x35x2 0084949 - 1 Tailboard cpl 1303949 1 - Tailboard cpl 1304150 1 1 Thread rod LH 3508751 2 2 Lock washer 0312852 2 2 Sliding block 3487853 2 2 Gas spring 0312754 2 2 Sliding block 4732755 1 1 Nut LH 3487756 1 1 Nut RH 3488057 1 1 Thread rod RH 35089

NotesQty

Pos Description Dimension Part.no