user manuals99e en 1.4
TRANSCRIPT
EN
GIN
E A
UT
OM
AT
ION
GEEA
User Manual SaCoS 99E
MAN Diesel SE SaCoS99E - User Manual Revision 1.4
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 2 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
© 2007 MAN Diesel SE
All rights concerning reprints or photomechanical reproduction of the whole document or
extracts of it (copies) and concerning translation reserved.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 3 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Contents
1 Safety Instructions ......................................................................................................... 4
2 Scope ............................................................................................................................... 4
3 System Description ........................................................................................................ 4
3.1 System Outline ................................................................................................................. 4
3.2 Engine ............................................................................................................................... 4 3.2.1 Local Control Station for 32/40 Engine Family .......................................................................... 5 3.2.2 Local Control Station for 48/60, 51/60, 58/64 Engine Families ................................................. 8
3.3 SaCoS .............................................................................................................................. 12 3.3.1 Auxiliary Cabinet ...................................................................................................................... 12 3.3.2 SaCoS Control Cabinets .......................................................................................................... 12 3.3.3 SaCoS Operating Panels ......................................................................................................... 13
3.4 System Integration ......................................................................................................... 82 3.4.1 System Outline ......................................................................................................................... 82 3.4.2 Alarm System ........................................................................................................................... 82 3.4.3 Propeller ................................................................................................................................... 82 3.4.4 Pump Control ........................................................................................................................... 82 3.4.5 Clutch Operation ...................................................................................................................... 83
4 Operation / Control ....................................................................................................... 84
4.1 Operating Hierarchy / Control Station ........................................................................... 84 4.1.1 Regular Operation (Remote) .................................................................................................... 84 4.1.2 External Control ....................................................................................................................... 84 4.1.3 Emergency Operation (Local) .................................................................................................. 84
4.2 Engine Startup ................................................................................................................ 85
4.3 Starting Preparations ..................................................................................................... 86
4.4 Engine Start .................................................................................................................... 87 4.4.1 Local Start ................................................................................................................................ 87 4.4.2 Remote Start ............................................................................................................................ 87 4.4.3 Emergency Start ...................................................................................................................... 91
4.5 Abnormal Conditions and Failure Messages ................................................................ 92 4.5.1 Alarm Treatment .................................................................................................................... 129
4.6 Media Temperature Control ......................................................................................... 138 4.6.1 Lubrication Oil Temperature Control ...................................................................................... 138 4.6.2 HT Cooling Water Temperature Regulation........................................................................... 139 4.6.3 Charge Air Temperature Regulation (CHATCO) ................................................................... 140 4.6.4 LT Cooling Water Temperature Regulation ........................................................................... 140
4.7 Engine Stop ................................................................................................................... 141
4.8 Temporary Engine Close-down ................................................................................... 142
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 4 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
1 Safety Instructions
Each system operation can influence the operating status of the attached engine. The engine is a power-generating plant with direct influence on the vessel’s propulsion and its power supply. Every time you intervene in the operation, please be aware of the consequences. Make sure, especially before the engine is started, that the engine start is approved and that there are not being done any works at the engine.
2 Scope
This operating manual describes the operation of MAN Diesel engines via a SaCoS operating and control system. In addition to this manual, please refer to the according chapters in the engine manual.
3 System Description
3.1 System Outline Each engine is connected with the control system SaCoS, which consists of engine-attached components, a local engine operating station; SaCoS control units as well as operating and display equipment for operations from a control room. The location of these components depends on the vessel’s design.
3.2 Engine Each sensor and actuator is connected to the SaCoS control cabinets via the engine terminal box and pluggable cable looms. The local control panel installed at the engine is designed as an emergency control panel and, therefore, only includes the operating and display elements needed for emergency operations.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 5 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3.2.1 Local Control Station for 32/40 Engine Family The control station serves for local supervision of the most important operating values and for engine operations during maintenance and repair works, or in case of an emergency with a disturbance of the SaCoS system.
1. Local-/Remote
Control Selector Switch
2. Engine Speed Setting
Twist Switch Lower/Raise
3.
Start Push Button
4. Acknowledge Engine is
turned Push Button
5. Emergency Stop
Push Button Switch
6. Signal Lamp
Turn gear engaged
7. Signal Lamp
Don’t Start
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 6 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
1. Selector Switch “ Local / Remote Control”
In position “Local“, an engine operation (start / stop) is only possible at the local engine control station. Solely an emergency stop is possible from other operating stands, too. The speed set point adjustment is carried out via the speed-setting switch “Lower/Raise” attached to the engine control station. In position “Remote Control”, the engine can be started from the SaCoS operating panel or, optionally, from external systems. In this mode of operation, the speed set point adjustment is carried out from SaCoS or the external system, which is normally the power plant control system.
2. Speed Setting Twist Switch “Lower/Raise”
At local control operation the engine speed is set by this switch. By using engine speed setting switch in position "Lower", engine speed setting is count down step by step as long as switch is hold in position. By using engine speed setting switch in position "Raise", engine speed setting is count up step by step as long as switch is hold in position.
3. Momentary Contact Push Button “Start”
At local operation the momentary contact push button “Start” permits the operator to start the
engine, if there is no start blocking active via SaCoS.
4. Momentary Contact Push Button “Acknowledge Engine is turned”
After turning the engine by the operator, this has to be acknowledged by pressing this push button. (This function is an option)
5. Illuminated Emergency Stop Push Button Switch (Electrical)
The electrical emergency stop switch acts on the emergency stop valve via the SaCoS system. Before another engine start is possible, the emergency stop switch must be released by pressing again. As long as the red lamp of the switch is illuminated, an emergency stop is active and an engine start is not possible. This lamp is also illuminated in case the emergency stop was, for instance, triggered in the engine control room or another place. The Reset then is to be carried out from there.
6. Signal Lamp “Turning Gear Engaged”
The signal lamp indicates that the turning gear is engaged and that an engine start is not possible.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 7 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
7. Signal Lamp “Don’t Start”
The signal lamp “Don’t Start” indicates, that the conditions for the engine start are not fulfilled. SaCoS will not permit a regular engine start.
8. Emergency Stop Push Button (Mechanical)
The emergency stop valve is provided with a mechanical emergency stop push button, which directly acts on the emergency stop valve. Thus, an engine emergency stop is possible even in case of a safety system breakdown.
9. Emergency Start Push Button (Mechanical)
At the emergency start valve, another push button is installed for mechanical actuating of the start valve. It works independently of the SaCoS system and can be used to start the engine in case of an engine control breakdown (Emergency Start).
8. Emergency Stop
Push Button
9. Emergency Start Push Button
For this start function, no start blockings of the operating and control system are active. The operator is fully responsible for the engine lubrication and cooling, as well as for the condition of the driven system! A pneumatic valve only prevents the engine start if the turning gear is engaged.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 8 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3.2.2 Local Control Station for 48/60, 51/60, 58/64 Engine Families
The control station serves for local supervision of the most important operating values and for engine operations during maintenance and repair works, or in case of an emergency with a disturbance of the SaCoS system.
3. Selector Switch
Mech./Elec. Governor 1. Start Push
Button
8. Emergency Stop
Push Button Switch 5. Signal Lamp
Don`t Start
4. Signal Lamp
Turn gear engaged
6. Signal Lamp Mech. Speed Setpoint Max
7. Signal Lamp Mech. Speed Setpoint Min
9. Acknowledge Engine
is turned Push Button
10. Engine Speed Setting Switch
Lower/Raise
2. Local-/Remote
Control Selector Switch
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 9 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
1. Momentary Contact Push Button “Start”
The start push button acts pneumatically directly on the start valve and works independently
of the control section changeover-switch position.
For this starting function, no start blockings of the safety and control system are active. The operator is fully responsible for the lubrication and cooling necessary for the engine, as well as for the condition of the driven system! A pneumatic valve only prevents the engine start if the turning gear is engaged.
2. Selector Switch “ Local / Remote Control”
In position “Local“, an engine operation (start / stop) is only possible at the local engine control station. Solely an emergency stop is possible from other operating stands, too. The speed set point adjustment is carried out via the switch button attached to the local engine control station. In position “Remote Control”, the engine can be started from the SaCoS operating panel or, optionally, from external systems. In this mode of operation, the speed set point adjustment is carried out from the external system, which is normally the propulsion control system.
3. Selector Switch “ Electr. Governor / Mech. Governor”
In position “Electronic Governor“ for normal operation, the speed setting is done via the controller installed in the SaCoS control cabinet, and via the electronic control unit in the mechanical speed control. Depending on the selected control-section, the speed set point is preset via digital raise / lower signals, or via an analogue set point signal. In position “Mech. Governor” for emergency operation, e.g. in case of electronic governor failure, speed setting is done by the backup ball head governor control. Engine operation with the backup governor should be carried out only in manual mode. Before starting the engine with the backup governor, the speed reference should be set to idle speed (indication at local control station) and PGG load limiter knob should be adjusted to approximate position 5, in order to avoid over speed at start. With the mechanical governor selected, engine start is only possible at local control station and a remote starting of the engine is interlocked.
4. Lamp “Turning Gear Engaged”
The illuminated lamp indicates that the turning gear is engaged and that an engine start is not possible.
5. Lamp “Don’t Start”
The illuminated lamp “Don’t Start” indicates that the conditions for the engine start are not fulfilled. SaCoS will not permit a regular engine start.
6. Lamp “Mech. Speed Set Point Max.”
The illuminated lamp indicates that the speed governor is set at maximum speed set point.
7. Lamp “Mech. Speed Set Point Min.”
The illuminated lamp indicates that the speed governor is set at minimum speed set point.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 10 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
8. Emergency Stop Button Switch (Electrical)
The electrical emergency stop button acts on the emergency stop valve via the SaCoS system. Before another engine start is possible, the electrical emergency stop push button switch must be released by pressing again. As long as the red lamp of the push button is illuminated, an emergency stop is active and an engine start is not possible. This lamp is also illuminated in case the emergency was, for instance, triggered in the engine control room or another place. The reset then is to be carried out from there.
9. Momentary Contact Push Button “Acknowledge Engine is turned”
After turning the engine by the operator, this has to be acknowledged by pressing this push button. (This function is an option).
10. Speed Setting Twist Switch “Lower/Raise”
At local control operation the engine speed is set by this switch. By using engine speed setting switch in position "Lower", engine speed setting is count down step by step as long as switch is hold in position. By using engine speed setting switch in position "Raise", engine speed setting is count up step by step as long as switch is hold in position.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 11 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
11. Emergency Stop Button (Mechanical)
The emergency stop valve is provided with a mechanical emergency stop push button, which directly acts on the emergency stop valve. Thus, an engine emergency stop is possible even in case of a safety system breakdown.
12. Emergency Start Button (Mechanical)
At the emergency start valve, another push button is installed for mechanical actuating of the start valve. It works independently of the SaCoS system and can be used to start the engine in case of an engine control breakdown (Emergency Start).
For this start function, no start blockings of the operating and control system are active. The operator is fully responsible for the engine lubrication and cooling, as well as for the condition of the driven system! A pneumatic valve only prevents the engine start if the turning gear is engaged.
12. Emergency Start
Push Button
11. Emergency Stop
Push Button
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 12 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3.3 SaCoS The Safety and Control System (SaCoS) do the operation and control of the engine. This system is divided into the subsystems “Safety System”, “Engine Control/Speed Control” and “Alarm Pre-Processing”. All subsystems work independently, but share information via a common system bus.
SaCoS usually consists of:
A wall-mounted auxiliary cabinet to be installed in the engine room
Two floor-mounted cabinets that can be installed either in the engine room or in the
engine control room
An operating panel, usually installed in the engine control room console
An optional indicating panel installed in the wheelhouse
3.3.1 Auxiliary Cabinet A wall-mounted auxiliary cabinet in the engine room actuates the electric motors, which are attached to the engine. These devices (starters) are operated via the SaCoS cabinets and are power-supplied by the
ship. For further information, see separate manual.
3.3.2 SaCoS Control Cabinets The SaCoS control cabinets are equipped only with signal lamps for the power supply and a “Reset” pushbutton. The “Reset” pushbutton only serves to reset the hardware emergency stop function in case of a SaCoS breakdown. For regular operation, no handling of the operating and control cabinets is necessary.
Safety System Cabinet
The safety system cabinet covers:
Safety functions (Automatic engine shutdown, Automatic load reduction)
Data Logging for EDS (Engine Diagnosis System)
Engine Control Cabinet
The engine control cabinet covers:
Engine control functions
Speed control
Alarm pre-processing (processing and transmission of all relevant data to the
machinery alarm system)
In case the system is being shut down for a longer period, it may be necessary to switch on the integrated cabinet heaters in order to prevent condensation of water inside the cabinets. Please be aware that in this case the corresponding operating power has to be supplied!
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 13 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3.3.3 SaCoS Operating Panels Engine operations are handled by an operating and display touch panel, which normally is installed in the engine control room and is equipped with an interactive touch display and hardware switches for system and emergency operations. The engine control room console can be equipped optionally with analogue speed indicators and media temperature control units. Optionally, another display panel on the bridge is available. Functions of this additional panel include emergency stop, override and indication of system alarms.
3.3.3.1 Engine Control Room Panel
The panel is used to operate the system functions of the engine, whereas the display indicates events, status and error messages about the current engine conditions. Switching -on / –off The display is controlled by the superordinated SaCoS-System. Switching the panel on or off is only possible via the SaCoS-System.
OPERATING PANEL
Display with its touch buttons to be pressed example: main overview
2
14
3
5a
4
8
6
5
12
7
9
10
11
13
1
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 14 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
1. Buzzer
An alarm for automatic stop, load reduction or auto disengaging, triggered while the “OVERRIDE“ function is active, is optically displayed by the safety system via the engine control room panel and audibly by a continuous signal (buzzer) sounding.
2. Illuminated momentary contact push button “AUTO SHUT DOWN”
If some parameters exceed specific values in the way that damage is probable (e.g. over speed, very low lubricating oil pressure), it is necessary to stop the engine. The safety system automatically stops the engine (Auto shut down). This event is visible by the red flashing light of the push button AUTO SHUT DOWN. Press the acknowledge push button to acknowledge the message. The red-flashing light will change to a permanent light signal. After an engine standstill, it is possible to reset the automatic stop of safety system by pressing the red-shining illuminated push button AUTO SHUT DOWN. After reset, the light of the push button turns off.
3. Illuminated momentary contact push button “AUTO REDUCE”
If some parameters exceed specific values (for instance exhaust gas temperature), the safety system requires a load reduction by a signal to the pitch or generator control. This event is visible by a red-flashing light of the push button AUTO REDUCE. Press the acknowledge push button to acknowledge the message. The red-flashing light will change to permanent light signal. In case of permissible parameters, it is possible to reset the AUTO REDUCE indication by pressing the red-shining illuminated push button. After reset, the light of the push button turns off.
4. Illuminated momentary contact push button “SYSTEM ALARM SAFETY SYSTEM”
In case of sensor - wire breaks, failures of PLC-modules, etc.; a system alarm occurs. This event is visible by the yellow flashing light of the push button SYSTEM ALARM SAFETY SYSTEM. Press the acknowledge push button to acknowledge the message. The yellow flashing light will change to permanent light signal. After repairing the wire break or any other defect, it is possible to reset the system alarm of the safety system by pressing the yellow shining illuminated push button. After reset, the light of the push button turns off.
5. Push button switch “EMERGENCY STOP”
In case of hazard for persons or engines, it is necessary to stop the engine immediately by pushing the EMERGENCY STOP push button. In this case, the engine stops without any delay. The push button switch must be unlocked before a reset of the emergency stop is possible.
5a. Lamp “EMERGENCY STOP”
In case of an emergency stop from any SaCoS-Panel the EMERGENCY STOP lamp is illuminated by permanent light signal.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 15 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
6. Illuminated momentary contact push button “SYSTEM ALARM ENGINE CONTROL”
In case of sensor - wire breaks, failures of PLC - modules, ect.; a system alarm occurs. This event is visible by the yellow flashing light of the push button SYSTEM ALARM ENGINE CONTROL. Press the acknowledge push button to acknowledge the message. The yellow flashing light will change to permanent light signal. After repairing the wire break or any other defect, it is possible to reset the system alarm of engine control system by pressing the yellow shining illuminated push button. After reset, the light of the push button turns off.
7. Momentary contact push button “ACKNOWLEDGE”
In case of system alarms, a yellow light at the responding illuminated push button begins to flash. Whereas a red light of the responding illuminated push button begins to flash in case of auto shut down, auto slow down or auto disengage. Press the acknowledge push button to accept the alarms, messages or stops that have occurred. All flashing lights will change to permanent light signals. A reset of an alarm / message is only possible after acknowledging. It is impossible to reset an alarm or a message (flashing light push button) without acknowledging.
8. Illuminated momentary contact push button “SYSTEM ALARM ALARM PRE-PROCESSING”
In case of sensor - wire breaks, failures of PLC - modules, ect.; a system alarm occurs. This event is visible by a yellow-flashing light of the illuminated push button SYSTEM ALARM ALARM PRE-PROCESSING. Press the acknowledge push button to acknowledge the message. The yellow flashing light will change into a permanent light signal. After repairing the wire break or any another defect, it is possible to reset the system alarm by pressing the yellow shining illuminated push button. After reset, the light of the push button turns off.
9. Momentary contact push button “TEST INDICATION LIGHTS”
To check the function of all lamps, press the push button “TEST INDICATION LIGHTS“. Please check the lamps regularly.
10. Selector switch “SPEED SET POINT - PANEL, EXTERNAL”
If engine control room panel is in operation and selector switch is in position panel, engine speed setting can be done by engine speed setting switch. In position external speed setting is done by an external control, for example propeller pitch control.
11. Twist switch “ENGINE SPEED - LOWER, RAISE”
By using engine speed twist switch in position "Lower", engine speed setting is count down step by step as long as switch is hold in position. By using engine speed twist switch in position "Raise", engine speed setting is count up step by step as long as switch is hold in position.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 16 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
12. Push button switch “OVERRIDE” (Optional)
This push button on the engine control room panel is a customer option. Usually, the standard override push button is installed in the wheelhouse. Considering the valuation “ship ranks before engine”, auto reduce, auto shut down or clutch-disengaging signals can be suppressed by the function “OVERRIDE”. With the aid of the “OVERRIDE” switch, the safety system function can be restricted to the issuing of alarms and messages. With the “OVERRIDE” function being active, most auto shutdowns, auto reductions and clutch disengagements, although requested, are not carried out by the safety system. Exceptions are manual emergency stop, over speed monitoring and additional alarms in accordance with the classification societies (such as, e.g., Oil Mist Detector, as specified by the classification society LR), which always have top priority and hence must not be suppressed. The procedure of a sequence is characterised as follows:
“OVERRIDE“ is actuated by the operator as a precaution prior to a difficult
manoeuvre (entering port, difficult passage, etc.), in order to suppress an automatic
function by the safety system. The alarm printer prints date and time of the
“OVERRIDE” activation. All pilot lamps on push buttons where OVERRIDE activation
is possible are illuminated.
An alarm for auto shut down, auto reduction or clutch disengaging, triggered while the
“OVERRIDE“ function is active, is displayed optically by the safety system via the
Engine Control Room Panel and audibly by a continuous signal (buzzer) sounding.
However, no reaction of the safety system occurs and there will be no impact on
engine operation. Suppressed alarms for auto shut down, auto reduce and clutch
disengaging are continued to be printed by the alarm printer with an indication that
the OVERRIDE function has been activated.
If the measuring value, responsible for an auto shut down, auto reduce or clutch
disengaging, returns into normal range during activated OVERRIDE function, the
buzzing stops and the message on the Engine Control Room Panel disappears
automatically.
Activating “OVERRIDE” will not abort safety system functions that have already been
triggered.
Engines, which have been stopped by the safety system, can be restarted.
To reset “OVERRIDE”, the push button has to be pressed again.
DANGER
Exemption from liability
The responsibility for the activation of the OVERRIDE function lies with the operator!
An abuse of this function with consequential damage to the engine or its surroundings relieves MAN Diesel SE from any liability!
Because engine monitoring is not working while the OVERRIDE function is activated, MAN Diesel SE can, in principle, not accept any liability for injuries to persons and damage to property, which are due to this fact.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 17 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
13. Push button switch “OVERRIDE CRANKCASE MONITORING” (Optional)
For some classification societies it is required to have a separate push button OVERRIDE CRANKCASE MONITORING. This is a customer option too and the standard push button is usually installed at wheelhouse, too.
14. Illuminated momentary contact push button “AUTO DISENGAGE CLUTCH” (Optional)
In case of auto shut down or operator engine stop, the clutch will be automatically disengaged. This event is visible by the red flashing light of the illuminated push button AUTO DISENGAGE CLUTCH. To acknowledge the message, press the acknowledge push button. The red-flashing light will change to a permanent light signal. After disengaging, it is possible to reset the automatic clutch-disengaging signal of safety system by pressing the red-shining illuminated push button. After reset, the light of the push button turns off.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 18 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3.3.3.2 Wheelhouse Panel
The wheelhouse panel is optional and is only delivered in case of a customer´s special order. The standard wheelhouse panel contains basic display and operating units. Additional display and operating units can only be attached optionally. If the operating control is handed over from the engine control room operating unit to the wheelhouse, the display and operating units of this operating unit will be activated. Only the emergency stop button is active at any time.
1. Buzzer
An alarm for automatic stop, load reduction or auto disengaging, triggered while the “OVERRIDE“ function is active, is optically displayed by the safety system via the engine control room panel and audibly by a continuous signal (buzzer) sounding.
2
3
10
11
1
12
12a
5
5a
7
9
6
8
4
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 19 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
2. Illuminated momentary contact push button “AUTO SHUT DOWN”
If some parameters exceed specific values in the way that damage is probable (e.g. over speed, very low lubricating oil pressure), it is necessary to stop the engine. The safety system automatically stops the engine (Auto shut down). This event is visible by the red flashing light of the push button AUTO SHUT DOWN. Press the acknowledge push button to acknowledge the message. The red-flashing light will change to a permanent light signal. After an engine standstill, it is possible to reset the automatic stop of safety system by pressing the red-shining illuminated push button AUTO SHUT DOWN. After reset, the light of the push button turns off.
3. Illuminated momentary contact push button “AUTO SLOW DOWN”
If some parameters exceed specific values (for instance exhaust gas temperature), the safety system requires a load reduction by a signal to the pitch or generator control. This event is visible by a red-flashing light of the push button AUTO SLOW DOWN. Press the acknowledge push button to acknowledge the message. The red-flashing light will change to permanent light signal. In case of permissible parameters, it is possible to reset the AUTO SLOW DOWN indication by pressing the red-shining illuminated push button. After reset, the light of the push button turns off.
4. Illuminated momentary contact push button “SYSTEM ALARM SAFETY SYSTEM”
In case of sensor - wire breaks, failures of PLC-modules, ect.; a system alarm occurs. This event is visible by the yellow flashing light of the push button SYSTEM ALARM SAFETY SYSTEM. Press the acknowledge push button to acknowledge the message. The yellow flashing light will change to permanent light signal. After repairing the wire break or any other defect, it is possible to reset the system alarm of the safety system by pressing the yellow shining illuminated push button. After reset, the light of the push button turns off.
5. Push button switch “EMERGENCY STOP”
In case of hazard for persons or engines, it is necessary to stop the engine immediately by pushing the EMERGENCY STOP push button. In this case, the engine stops without any delay. The push button switch must be unlocked before a reset of the emergency stop is possible.
5a. Lamp “EMERGENCY STOP from other PLACE”
In case of an emergency stop from any other SaCoS-Panel the “EMERGENCY STOP from other PLACE” lamp is illuminated by permanent light signal.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 20 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
6. Illuminated momentary contact push button “SYSTEM ALARM ENGINE CONTROL”
In case of sensor - wire breaks, failures of PLC - modules, ect.; a system alarm occurs. This event is visible by the yellow flashing light of the push button SYSTEM ALARM ENGINE CONTROL. Press the acknowledge push button to acknowledge the message. The yellow flashing light will change to permanent light signal. After repairing the wire break or any other defect, it is possible to reset the system alarm of engine control system by pressing the yellow shining illuminated push button. After reset, the light of the push button turns off.
7. Momentary contact push button “ACKNOWLEDGE”
In case of system alarms, a yellow light at the responding illuminated push button begins to flash. Whereas a red light of the responding illuminated push button begins to flash in case of auto shut down, auto slow down or auto disengage. Press the acknowledge push button to accept the alarms, messages or stops that have occurred. All flashing lights will change to permanent light signals. A reset of an alarm / message is only possible after acknowledging. It is impossible to reset an alarm or a message (flashing light push button) without acknowledging.
8. Illuminated momentary contact push button “SYSTEM ALARM ALARM PRE-PROCESSING”
In case of sensor - wire breaks, failures of PLC - modules, ect.; a system alarm occurs. This event is visible by a yellow-flashing light of the illuminated push button SYSTEM ALARM ALARM PRE-PROCESSING. Press the acknowledge push button to acknowledge the message. The yellow flashing light will change into a permanent light signal. After repairing the wire break or any another defect, it is possible to reset the system alarm by pressing the yellow shining illuminated push button. After reset, the light of the push button turns off.
9. Momentary contact push button “LAMP TEST”
To check the function of all lamps, press the push button “LAMP TEST“. Please check the lamps regularly.
10. Lamp “STOP ENGINE”
With the "OVERRIDE" function being active, an alarm requests an engine stop by the operator. The lamp „STOP ENGINE“ indicates this. At the same time, the buzzer sounds.
11. Lamp “REDUCE LOAD”
With the "OVERRIDE" function being active, an alarm requests a load reduce by the operator. The lamp „REDUCE LOAD“ indicates this. At the same time, the buzzer sounds.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 21 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
12. Push button switch “OVERRIDE”
Considering the valuation “ship ranks before engine”, auto reduce, auto shut down or clutch-disengaging signals can be suppressed by the function “OVERRIDE”. With the aid of the “OVERRIDE” switch, the safety system function can be restricted to the issuing of alarms and messages. With the “OVERRIDE” function being active, most auto shutdowns, auto reductions and clutch disengagements, although requested, are not carried out by the safety system. Exceptions are manual emergency stop, over speed monitoring and additional alarms in accordance with the classification societies (such as, e.g., Oil Mist Detector, as specified by the classification society LR), which always have top priority and hence must not be suppressed. The procedure of a sequence is characterised as follows:
“OVERRIDE“ is actuated by the operator as a precaution prior to a difficult
manoeuvre (entering port, difficult passage, etc.), in order to suppress an automatic
function by the safety system. The alarm printer prints date and time of the
“OVERRIDE” activation. All pilot lamps on push buttons where OVERRIDE activation
is possible are illuminated.
An alarm for auto shut down, auto reduction or clutch disengaging, triggered while the
“OVERRIDE“ function is active, is displayed optically by the safety system via the
Engine Control Room Panel and audibly by a continuous signal (buzzer) sounding.
However, no reaction of the safety system occurs and there will be no impact on
engine operation. Suppressed alarms for auto shut down, auto reduce and clutch
disengaging are continued to be printed by the alarm printer with an indication that
the OVERRIDE function has been activated.
If the measuring value, responsible for an auto shut down, auto reduce or clutch
disengaging, returns into normal range during activated OVERRIDE function, the
buzzing stops and the message on the Engine Control Room Panel disappears
automatically.
Activating “OVERRIDE” will not abort safety system functions that have already been
triggered.
Engines, which have been stopped by the safety system, can be restarted.
To reset “OVERRIDE”, the push button has to be pressed again.
DANGER
Exemption from liability
The responsibility for the activation of the OVERRIDE function lies with the operator!
An abuse of this function with consequential damage to the engine or its surroundings relieves MAN Diesel SE from any liability!
Because engine monitoring is not working while the OVERRIDE function is activated, MAN Diesel SE can, in principle, not accept any liability for injuries to persons and damage to property, which are due to this fact.
12a. Lamp “OVERRIDE FROM OTHER PLACE”
If the "Override" function was triggered from another operating unit, the lamp "OVERRIDE FROM OTHER PLACE" is illuminated by permanent light signal.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 22 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3.3.3.3 Touch Screen Display
3.3.3.3.1 General Information on the Display Structure:
Cut line:
1: Headline
The headline shows the description of the current display. With contents on more than one page the number of the current display and the total number of pages is indicated on the left hand side. The grey button gives information on service adresses.
By pressing the MAN emblem in the headline, all service addresses of MAN DIESEL SE in Germany will be displayed.
Via the MAN emblem this button appears: By pressing it, worldwide service telephone numbers are displayed.
1: Headline 4: Field of Alarms
2: Status Line 5: Horizontal Navigation Bar
3: Field of Information
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 23 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
2: Status Line
The Status Line is located below the headline. This line shows always data as follows:
• Engine Speed in 1/min (rpm)
• Fuel Index in %
• Engine Power in KW (optional)
• Date and time (optional).
The Status Line is positioned at the same place in nearly every display.
3: Field of Information
There are different kinds of fields of information: their structures vary depending on data or buttons displayed. It is the most important part of every single page as it shows new information or helps to navigate through the menus.
Within the field of information, for example the MAIN MENU (see above), it is possible to go to the desired screen pages by pressing the accordant buttons displayed.
Within the field of information of the ALARM MANAGEMENT the last active alarms are displayed and classified in categories.
Within the field of information of the Main Alarm List all-current, acknowledged or reset alarms are listed. Therefore see the differentiation of colours in chapter 3.3.3.3.2/III) Alarm Buttons - 4. Alarm Representation.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 24 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4: Field of Alarm
Directly beneath the field of information the field of alarm is located. Within this field the last occurred alarm would be displayed. The field of alarm is positioned at the same place in every display.
5: Navigation Bar
The navigation bar with its menu and function buttons is positioned below the field of alarm.
Example: Main Menu
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 25 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3.3.3.3.2 Indication of Buttons, Symbols and Colors appearing on different screen pages
This chapter contains the following topics:
Explanation of colours and their meanings.
Explanation of all buttons, which appear in the display.
Overview of “Indication of Buttons, Symbols and Colours”:
I. General Descriptions.................................................................................................... 27
1. Buttons: Representing Functions of Being (In-) Active ............................................ 27
2. Representing pressed Buttons (optional) .................................................................. 28
3. Buttons with a Double Function ................................................................................. 28
4. Meaning and Status of different Colours ................................................................... 28
5. Colours: Representing Engine Speed ........................................................................ 29
6. Colours: Displaying Measured Values (Bars) ............................................................ 29
7. Representation of the State of Pumps ....................................................................... 29
II. Buttons for Navigation ................................................................................................ 31
1. General Navigation ...................................................................................................... 31
2. Navigation in the Main Alarm List and Histogram ..................................................... 31
III. Alarm Buttons ............................................................................................................. 32
1. Alarm Processing ........................................................................................................ 32
2. Procedure to Reset Error Blocks ............................................................................... 32
3. Navigation Buttons ...................................................................................................... 34
4. Alarm Representation ................................................................................................. 34
5. Alarm Groups .............................................................................................................. 37
6. Alarm – List of Abbreviations ..................................................................................... 41
IV. Menu Buttons ............................................................................................................. 42
1. Horizontal Navigation Bar Buttons on every single page ......................................... 42
2. Buttons within the Field of Information ..................................................................... 42
V. Buttons in the Horizontal Navigation Bar ................................................................. 45
1. Within the Main Menu’s submenus “Media”, “Exhaust Gas”, “Splash Oil”,
“Main Bearing” .......................................................................................................... 45
2. Within the Main Menu’s submenus “Fuel”, “Cooling Water”, “Air
Systems”, “Lube Oil” ................................................................................................ 45
3. Within the Main Menu’s submenu Engine Start/Stop................................................ 46
4. Within the Main Menu’s submenus Clutch Control ................................................... 46
5. Within the Menu Diverse the submenu PLC-Diagnostic ........................................... 46
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 26 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
VI. Buttons with Special Functions ................................................................................ 47
1. Engine Start/Stop Operation ....................................................................................... 47
2. Clutch Control ............................................................................................................. 47
3. Control Cylinder Lubrication ...................................................................................... 48
4. PLC- Diagnostic ........................................................................................................... 48
VII. Further Buttons and their Functions ....................................................................... 49
1. Safety Passwords ........................................................................................................ 49
2. Buttons to control Temperature ................................................................................. 49
3. Buttons to control Air or Fuel ..................................................................................... 50
4. Display Keyboard ........................................................................................................ 50
5. Lamp Test .................................................................................................................... 50
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 27 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
I. General Descriptions
1. Buttons: Representing Functions of Being (In-) Active
Inactive buttons can’t be pressed due to their deactivated function. Active and inactive buttons are coloured differently as it is explained as follows:
Button Engine Start / Stop
a) Buttons with authorised operation b) Buttons without authorised operation
Field of Information
c) Buttons without function
With an electronic injection system a special button is located in the navigation bar.
Empty, inoperable button as placeholder for optional functions.
Navigation Bar
Field of Information
Navigation Bar
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 28 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
2. Representing pressed Buttons (optional)
After being pressed, some grey buttons in the field of information change their colour into blue. After being pressed, confirmation buttons change their colour only shortly. During longer processes the button remains blue while the process is in progress.
This kind of representation appears only with electronic injection systems and systems with temperature regulators.
3. Buttons with a Double Function
By pressing these buttons, it is possible to change between Measuring Point and Text. The button changes according to the inactive way of representing.
Displaying measuring points in "Codeform" (for instance: 1PT5070).
Displaying measuring points in text form (for instance: fuel).
4. Meaning and Status of different Colours
Coloured status displays distinguish the status of a particular event and are peculiar to different combinations (specific to each menu). Meaning and Status of different Colours
Colour green light blue yellow red colourless
Status automatic control
data O.K Process/S
tatus is aktive.
normal control
data O.K.
process /
status is
active
alarm
(an error has occurred)
alarm(s) existent
(an error has
occurred)
no alarm existent
manual regulation
Process/Status is inactive
Button which is pressed (Process active). Button which is not pressed (Process inactive).
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 29 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
5. Colours: Representing Engine Speed
6. Colours: Displaying Measured Values (Bars)
Measured values are displayed by means of vertical and horizontal bars with certain colours:
Meanings of colours in data displays
Bars
Colours green yellow red crossed out without bar
crossed out with bar
Meaning Sensor O.K. Value O.K.
alarm Automatic Shutdown or load reduction
Wire break, sensor not existent
Shutdown due to calculation error
7. Representation of the State of Pumps
Visibility and specification of the pumps depend on the type of engine (V-Engine, L-Engine) and if there is an electronic injection system.
grey green
pump off pump on
The picture is located in the top left corner on the display’s homepage and shows the current engine speed graphically and on a value basis in the dimension unit 1/min (rpm). The graphic differentiates certain ranges of speed in colour. Yellow Abnormal engine speed, only during start and Stop of
engine Green Normal Speed can only start when idling engine speed
is existent and it ends with 103% nominal speed. Red Over Speed
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 30 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
8. Representation of the State of Command Console
Indicationn of the Command Console that actual have the engine command authority, by an activated green lamp.
The Indication of the Command Console is specially displayed on screens with permission to command the engine or pumps and on the override screen.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 31 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
II. Buttons for Navigation
Navigation means “moving“ from one page to another one, between different menus and datasets.
1. General Navigation
Return up to the last nine pages visited.
Go to the next screen page. Button is only existent if contents range from more than one page. (for instance: 1
st page of 3 in total
- In the headline appears "1_/_3")
Go back to the last screen page. Button is only existent if contents range from more than one page. (for instance: 2nd and last page - In the headline appears "2_/_2")
2. Navigation in the Main Alarm List and Histogram
Go back to the last screen page and quit menu respectively.
Scroll up and down in datasets.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 32 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
III. Alarm Buttons
1. Alarm Processing
Basic Sequences of Alarm Processing
2
2. Procedure to Reset Error Blocks
Alarms are thematically combined in groups (blocks). The following shows how alarms (activated and acknowledged) are reset block by block.
The menu RESET ERROR BLOCK is displayed:
Menu Reset Error Block
1
An activated alarm is displayed in the field of alarm.
1. To acknowledge any activated alarm, press one of the buttons displayed on the left hand side (1).
2. Fix the error that caused the alarm.
3. Reset the alarm by pressing one of the menu buttons on the left (2).
Once the alarm was reset, it disappears from the MAIN ALARM LIST as well as from the field of alarm.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 33 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
This menu provides functions as follows:
Reset Block – Safety System:
To reset the safety system, press the button errors safety system in the menu RESET ERROR BLOCK.
Once this button was pressed, the menu Reset Block – Safety System is displayed.
Go to the menu Errors –Safety System.
- Left button: Reset alarm System Errors – Alarmpreprocessing Unit.
- Right button: Go to the alarm list Group E-F. (E: Preprocessing alarms - AlSys, F: System alarms - AlSys)
- Left button: Reset alarm System Errors – Engine Control.
- Right button: Go to the alarm list Group D. (system alarms -E.C.-)
- Left button: Reset alarm Errors – Speed Governor
- Right button: Go to the alarm list Group D
(system alarms -E.C.-)
(
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 34 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
This menu provides functions as follows: Reset Error Blocks – Safety System
Left button: Reset the alarm Automatic Shutdown / Disengage.
Right Button: Go to the alarm list Group A (Automatic Shutdown – Safsys.)
Left button: Reset Automatic Slowdowns. Right button: Go to the alarm list Group B
(Reduce -SafSys-).
Left button: Reset the system alarm.
Right button: Go to the alarm list Group C (System alarms -Saf-
Sys-).
3. Navigation Buttons
By pressing these following buttons, the Main Alarm List will be displayed:
Located in the vertical navigation bar.
Located in the horizontal navigation bar.
For further information see chapter 4.5.1.2 Using all Functions of the Main Alarm List.
4. Alarm Representation
Alarm Bell:
When a new alarm is activated, this flashing bell will appear. This symbol is located in the top right corner on every single screen page.
By pressing this symbol, it is possible to go to the Main Alarm List. The warning bell
will disappear when all activated alarms are acknowledged.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 35 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Field of Alarm:
The field of alarm is located in the lower third of the display on almost every single screen page.
In this single-lined field the last activated alarm will be displayed.
(there is no activated alarm in this example).
Marking of alarms which are not acknowledged in the field of alarm:
A current activated, but not acknowledged alarm (e.g. an Override-Alarm) is marked
- With a star "*" in front of the alarm text and
- By white font on a dark-grey background.
Marking of acknowledged alarms in the field of alarm:
An acknowledged alarm (e.g. an Override-Alarm) is marked
- With a dash "-" in front of the alarm text and
- by yellow font on a dark-grey background.
Meanings of colours in the Main Alarm List:
A current activated, but not acknowledged alarm (e.g. an Override-Alarm) is marked
- With a star "*" in front of the alarm text and
- By yellow font on a pink background.
An acknowledged alarm (e.g. an Override-Alarm) is marked
- With a dash "-" in front of the alarm text and
- By white font on a green background.
A reset, but not activated alarm (e.g. an Override-Alarm) is marked
- By black font on a light-grey background.
This last alarm is only a histogram text.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 36 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Main Alarm List – alarms acknowledged
Main Alarm List – example for a not acknowledged alarm
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 37 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Marking Alarms in the Main Alarm List:
As in the field of alarm, the alarms in the Main Alarm List are marked with the following symbols in front of the alarm text:
Symbol Alarm Status
* active, not acknowledged
$ inactive, not acknowledged
- active, acknowledged
No symbol inactive, acknowledged
Marking Alarms with an active Histogram Function:
If the histogram function (date and time-stamp) is active, the alarm lines are marked with the following letters in front of the alarm text.
Alarm Time Notation Meaning
S Moment of Appearance/Start
A Moment of Acknowledgment
E Moment of Erasure
5. Alarm Groups
The alarms are divided into groups as follows:
Alarm Group
Alarm Description System
A Automatic Shutdown - SafSys- Safety System
B Reduce -SafSys- Safety System
C System Alarms -SafSys- Safety System
D System Alarms -E.C.- Engine Control
E Prealarm -AlSys- Alarm Pre-processing
F System Alarms -AlSys- Alarm Pre-processing
Accessing Alarm Groups:
The access is possible by pressing the button ALARM GROUPS in the MAIN MENU or on any other screen page where the button appears. Display 1 ALARM MANAGEMENT (2 in total) with its Groups A to C will show up.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 38 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Structure and Function of the menu Alarm Management:
Alarm Management, Group A to C
Cutline:
4: The vertical navigation bar provides the following functions: Alarm Management
By pressing one of these buttons, it is possibe to go directly to the chosen alarm group in the Main Alarm List:
A: Automatic shutdown -SafSys-, B: Reduce -SafSys- C: System alarms -SafSys-
D: System alarms -E.C.-, E: Prealarm -AlSys- F: System alarms -AlSys-
1: Headline 4: Vertical Navigation Bar (see below)
2: Status Line 5: Field of Alarms
3: Field of Information 6: Horizontal Navigation Bar
Help-Symbol
Go to the page ALARM-TROUBLE SHOOTING
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 39 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Elements in the Main Alarm List:
Buttons in the Main Alarm List and Histogram:
There is no information on the marked alarm available.
There is problem-solving information on the marked alarm available.
By pressing this button, information on error processing are displayed.
By pressing this button, zooming in the alarm lines is possible up to four times.
This button is only located in the Main Alarm List to display or hide date and time-stamp for the alarms.
This button is only located in the histogram page:
By pressing this button, all inactive alarms will be deleted from the histogram. This function is password protected.
The histogram screen page is not yet functional.
Buttons to Troubleshoot Alarms: see 4.5.1.3 PLC – Troubleshooting
By pressing this button, an overview of possible error messages of the display will be shown.
By pressing this button, commonly used abbreviations will be displayed on two screen pages (see the next sub-chapter 6. Alarm – List of Abbreviations).
This button is only available in case of engines with WAGO-PLC and consequently optional.
This button is only available in case of engines with ABB-PLC and consequently optional.
Show all alarms.
Press one of the groups to choose the wanted alarm group (in this example only the alarms of GROUP D will be displayed).
To choose the alarm groups (All or Group A to D), scroll to the left or to the right by means of the arrows, which appear in the bar. In this case only the active buttons can be used.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 40 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Buttons for Troubleshooting (only existent with ABB control):
see 4.5.1.3 PLC – Troubleshooting
By pressing this button, the description of failure class 1 (fatal error) will be displayed.
By pressing this button, the description of failure class 2 (serious error) will be displayed.
By pressing this button, the description of failure class 3 (light error) will be displayed.
By pressing this button, information on PLC-LEDs will be displayed.
Buttons for Details –Error Processing:
see 4.5.1.2 Using all Functions of the Main Alarm List
Choose the button with the adequate ID-Zone.
Slide switch is displayed to choose the exact ID (alarm numbers).
Within the slide switch field:
Confirm the chosen ID and hide the slide switch.
Slide switch to choose the ID from (alarm numbers).
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 41 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
6. Alarm – List of Abbreviations The following chart lists all abbreviations, which appear in menus and alarm messages.
Abbreviation Meaning Abbreviation Meaning
Aft.; AFT. after I/O input/output
AlSys; AP; APU; ALARM PREPROC.
alarm preprocessing LUB.; LUBRIC. lubrication
BEAR. bearing LT low temperature
Bef.; BEF. before MED. medium
COOL. cooling system MVD mean value deviation
CONNECT. connection OVRD DSENG override disengaged
COMM. communication OVRD RED override reduce
COMP. (engine) compartment OVRD SD override shutdown
COMPS. compensation
CR common rail PGI performance gas injection
CYL. cylinder PreAl. prealarm
CW cooling water PREPROC. preprocessing
Dev.; DEVIAT. deviation PRESS. pressure
DF Dual Fuel RED reduce
DIFF. difference SAF.SYST.; SafSys
safety system
DSENG disengaged SD shutdown
EC; E.C. engine control SETP. setpoint
EC-SYST. engine control system SF sensor error
EMERG. emergency TEMP. temperature
ERR. error TC turbo charger
EXH. exhaust WB wire break
FEEDB.ERR. feedback error ECR engine control room
FUNCT. function LOP local operation panel
FUNCT.ERR. function error BRIDGE main bridge
GENER. generator WING bridge wing
HT high temperature
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 42 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
IV. Menu Buttons
1. Horizontal Navigation Bar Buttons on every single page
Go to the first screen page, the MAIN OVERVIEW.
Go to the MAIN MENU.
In the Main Overview and different screen pages:
Go to the menu Splash Oil. Go to the menu Exhaust Gas. Go to the menu Main Bearing.
2. Buttons within the Field of Information
In the Main Menu:
Go to the menu Splash Oil. Go to the menu Exhaust Gas. Go to the menu Main Bearing.
Go to the menu Fuel. Go to the menu Cooling Water. Go to the menu Air.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 43 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Go to the menu Lube Oil. Go to the menu Media Overview.
Go to the menu Engine Status.
Go to the screen page
Engine Attached Equipment.
Go to the menu
DIVERSE.
Button is only active if authorised operation is permitted.
Go to the menu Engine Start/Stop.
Go to the menu Manual Operations. Button is optional.
Go to the menu Clutch Control.
In the Menu Diverse:
To change date and time, a password is required.
By pressing this button, the menu for safety passwords will be displayed.
By pressing this button, Display Diagnostic will come up.
Go back to the Menu Diverse by touching the display screen.
Technical data of the display will come up.
Go to the display to control the backlight.
Adjust the lightness of the display with this slide switch:
0: brighter <--> 50: darker
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 44 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
This button gives information on the Software (Projekt Info).
Display the IMO-VIT Parameters.
By pressing this button redundant values will be displayed.
This button only appears by unauthorised operation of "Engine Start/Stop ".
Go to the list Start- Blockings and Failures.
This button is password protected. Access only for service staff and commissioning engineers.
By pressing this button, the service pages will be displayed.
Go to the menu to select a language. The following languages can be set: English, German, Spanish and Portuguese. The last adjustment used will be saved automatically.
With the following slide switch, it is possible to change dimension units:
O: bar , °C <--> I: psi, °F
The translation is carried out automatically. The adjustment will be saved subsequently.
This button only appears by unauthorised operation of "Engine Start/Stop ".
Go to the list Clutch-/Blockings and Failures.
Button is optional.
Go to the menu Turbine Disc-Cooling. Meassured data will be displayed..
Go to the menu PLC- Diagnostic.
This function is not yet available.
By pressing this button, the histogram will be displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 45 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
V. Buttons in the Horizontal Navigation Bar
1. Within the Main Menu’s submenus “Media”, “Exhaust Gas”, “Splash Oil”, “Main Bearing”
In the submenu Temperature Values:
Change to the screen page Mean Value Deviation.
Change to the screen page Sensor Status of the particular medium.
In the submenus Mean Value Deviation, Sensor Status:
2. Within the Main Menu’s submenus “Fuel”, “Cooling Water”, “Air Systems”, “Lube Oil”
Medium Lubrication Oil (optional):
Cooling Water – Values (optional): Air-Values (optional):
Change to the display Temperature Controller Cooling Water HT.
Change to the display Temperature Controller Cooling Water LT.
Change to the display Temperature Controller Intake Air.
Change to the display Temperature Controller/Charge Air.
Change to the display Temperature Values of the particular medium.
Change to the display Temperature Controller Lube Oil.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 46 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3. Within the Main Menu’s submenu Engine Start/Stop
Start - Blockings and Failures (only active if authorised operation is permitted):
Engine Start / Stop Operation:
4. Within the Main Menu’s submenus Clutch Control
Clutch Blockings and Failures (only active if authorised operation is permitted):
5. Within the Menu Diverse the submenu PLC-Diagnostic
Alarm Troubleshooting:
Go to the list Start - Blockings and Failures.
Go to the menu Engine - Start / Stop.
Go to the menu Clutch Control.
Go to the list Clutch - Blockings and Failures.
Go to the menu PLC-Diagnostic.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 47 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
VI. Buttons with Special Functions
The following buttons are not located in the navigation bars, but in the field of information.
1. Engine Start/Stop Operation
Buttons are only active if accordant messages are displayed:
2. Clutch Control
Buttons are only active if particular messages appear:
By pressing this button, engage or disengage.
Reset Clutch-/Blockings and Failures after their correction.
Show current blockings and go to the list DF-Modus Blockings/Failures.
Confirm chosen operation (engage or disengage).
Start engine. Stop engine.
Reset Start-/Blockings and Failures after their correction.
Show start blockings. Confirm chosen operation (Start or Stop).
Acknowledge message that indicates: Engine is manually turned.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 48 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3. Control Cylinder Lubrication
The following functions are only available if the engine stands still.
Activate manual cylinder lubrication. Deactivate manual cylinder lubrication.
Operating Status from at least 50 % filling:
Operating Status after the engine start:
Button will be inactive after having been manually turned:
4. PLC- Diagnostic
PLC-DIAG.: Safety System is displayed PLC-DIAG.: Engine control is displayed.
The following buttons are optional ones:
This button is only existent if a separate control is set.
PLC-DIAG.: Alarm Preprocessing is displayed.
PLC-DIAG.: Speed Governor Control is displayed.
Change cylinder lubrication into automatic-mode.
Change cylinder lubrication into run in-mode.
Acknowledge that the engine is manually turned.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 49 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
VII. Further Buttons and their Functions
1. Safety Passwords
Access only for service staff and commissioning engineers:
2. Buttons to control Temperature
a) Optional Function:
Increase or decrease temperature (setpoint). Enter setpoint with display keyboard.
b) Optional Buttons (System with Temperature Control):
Accept adjustment or value.
Access only for service staff. To change parameters, a password is required.
Save changes in EEPROMs.
Activate the particular display manually.
Self-explanatory Self-explanatory
Log in with user password at a certain level.
After an hour the user will be logged out automatically.
Log out with user password at a certain level.
After an hour the user will be logged out automatically. Changes will be automatically saved.
Green sliding switch indicates that the option is activated.
Red sliding switch indicates that the option is deactivated.
Button is password protected.
Password required to adjust date and time.
Date and time is to be adjusted by typing it in with the display keyboard.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 50 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3. Buttons to control Air or Fuel
4. Display Keyboard
5. Lamp Test
1.
2.
Open or close the damper.
This display keyboard appears if user input is required (for example: access to a password protected menu).
Once the lamp test is in progress, button 2 will appear.
Check to see if the signal lights on the operating panel are in working order. Once this button was pressed all signal lights flash up for three seconds (optional button).
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 51 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3.3.3.3.3 Main Overview
The MAIN OVERVIEW appears automatically, once the display is switched on via the SaCoS-System. By pressing the button MAIN OVERVIEW in other menus, it is possible to go back to the MAIN OVERVIEW that appeared at first.
The MAIN OVERVIEW display offers valuable clues and settings, which are clearly arranged.
Main Overview with examples of data
Cut line:
1: Engine Speed 4: Field of Status (see below)
2: Field of Information (see below) 5: Field of Alarms
3: Start Status (see below) 6: Navigation Bar
Within the picture the measuring points are displayed in written form and the remote control is activated.
Abbreviations in the top left corner of the display mark the location of particular panels:
Abbreviation Location of different Panels
LOP (Local Operator Panel) on the engine
ECR in the engine control room
Bridge at the bridge
Port Wing at the port wing of the bridge
STBD Wing at the wing of the bridge (Starboard)
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 52 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
2: Field of Information
Within this field of information all current measured values will be displayed graphically.
Data of the following media will be displayed:
• FILLING in %
• SPEED TC -A- 1/min (rpm)
• SPEED TC -B- 1/min (rpm)
• HT- COOLING WATER IN FRONT OF ENGINE IN bar
(psi)
• NT- COOLING WATER CHARGE AIR in bar (psi)
• CONTROL AIR in bar (psi)
• LUBE OIL ENGINE in bar (psi)
• COUNTDOWN in Sek.
• NEEDLE VALVE IN COOLING WATER in bar (psi)
• CHARGE AIR in bar (psi)
• STARTING AIR in bar (psi)
• LUBE OIL TC in bar (psi)
• FUEL in bar (psi)
3: Start Status
The field START STATUS is located within the field of information. This field indicates current messages on activated processes at the engine.
The following messages can appear within the field START STATUS:
PRESSURE FORMATION
PRELUB. RUNNING
SLOW TURN RUNNING
START AIR RLEASED
ENGINE IS STARTING
ENGINE STOPPED
ENGINE RUNNING
ENGINE IS STOPPING
STARTING FAILURE
START BLOCKED
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 53 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
LOCAL START RUNNING
GENERATOR BREAKER SWITCH -ON-
CLUTCH IS ENGAGED
RUNNING / STOP BLOCKED
4: Field of Status
Within this field the following processes and settings are marked:
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 54 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3.3.3.3.4 Main Menu
Main Menu - Overview
I. Structure ........................................................................................................................ 55
II. Functions ..................................................................................................................... 55
1. Splash Oil, Exhaust Gas and Main Bearing ............................................................... 56
2. Fuel, Cooling Water, Air Systems, Lube Oil .............................................................. 59
3. Media Overview ........................................................................................................... 61
4. Engine Status .............................................................................................................. 61
5. Engine Attached Equipment ....................................................................................... 63
6. Confirm Engine Start / Stop ........................................................................................ 63
7. Manual Operations ...................................................................................................... 65
8. Clutch Control ............................................................................................................. 67
The following functions of the MAIN MENU are explained in different chapters. That is why these menus are not described in detail below.
ALARM GROUPS: see chapter 3.3.3.3.2/III) Alarm Buttons – 5. Alarm Groups.
DIVERSE: see chapter 3.3.3.3.5 Menu Diverse.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 55 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
I. Structure
Cutline:
1: Headline 4: Field of Alarms
2: Status Line 5: Navigation Bar
3: Field of Information (see below)
This picture shows the MAIN MENU if an authorised operation is permitted.
3: Field of Information
Within this field the following buttons are located in order to go to certain pages as follows:
• Splash Oil
• Exhaust Gas
• Main Bearing
• Fuel
• Cooling Water
• Air
• Lube Oil
• Media Overview
• Engine Status
• Engine Attached Equipment
• Diverse
• Engine Start / Stop
• Manual Operations
• Electronic Injection System (optional)
• Clutch Control (optional)
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 56 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
II. Functions
How to access the Main Menu:
1. Splash Oil, Exhaust Gas and Main Bearing
How to display Splash Oil, Exhaust Gas and Main Bearing:
By pressing the particular button to display splash oil, exhaust gas or main bearing, an overview of TEMPERATURE VALUES according to each menu will show up.
Example: Overview of Splash Oil Temperature Values.
Press the button MAIN MENU in the navigation bar of the MAIN OVERVIEW.
or:
Press this button MAIN MENU on any screen page where it is displayed.
The display MAIN MENU will be shown consequently.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 57 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
It is possible to go to the following overviews of SPLASH OIL-, EXHAUST GAS- or MAIN BEARING via the horizontal navigation bar:
SPLASH OIL or EXHAUST GAS MEAN VALUE DEVIATION
SPLASH OIL, EXHAUST GAS or MAIN BEARING SENSOR STATUS
Please note: The overviews SPLASH OIL-, EXHAUST GAS- or MAIN BEARING- TEMPERATURE VALUES and MEAN VALUE DEVIATION display all existent and absolute data graphically and on a value basis by means of bars.
How to display Mean Value Deviation:
Example: Overview of Splash Oil Mean Value Deviation
Please press the button MEAN VALUE DEVIATION on the screen pages SPLASH OIL- or EXHAUST GAS-TEMPERATURE VALUES.
The screen page SPLASH OIL- or EXHAUST GAS- MEAN VALUE DEVIATION will be displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 58 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
How to display Sensor Status:
Example: Overview of Splash Oil Sensor Status
The particular overview of SPLASH OIL-, EXHAUST GAS- or MAIN BEARING-SENSOR STATUS DISPLAYS the evaluated states of sensors in written form.
The following messages can appear:
status Meaning
O.K. Sensor works correctly. There are no alarms due to wire break etc.
SENSOR FAULT Wire break or failure existent.
PRE-ALARM MAX / MIN Measured value of sensor exceeded maximum or minimum value for pre-alarm.
PREALARM MVD Measured value of sensor exceeded maximal acceptable mean value deviation for pre-alarm.
SLOW DOWN MAX/MIN Measured value of sensor exceeded maximal or minimal value for slowdown.
SLOW DOWN MVD Measured value of sensor exceeded maximal acceptable mean value deviation for slowdown.
SHUTDOWN MAX / MIN
Measured value of sensor exceeded maximal or minimal value for shutdown.
SHUTDOWN MVD
Measured value of sensor exceeded maximal acceptable mean value deviation for shutdown.
CUT-OFF Sensor will not be processed since its value is above of the defined limit.
On the screen pages SPLASH OIL-, EXHAUST GAS- or MAIN BEARING TEMPERATURE VALUES, please press the button SENSOR STATUS.
or:
Press the button SENSOR STATUS in the navigation bar.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 59 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
2. Fuel, Cooling Water, Air Systems, Lube Oil
How to display values about Fuel and Cooling Water, Air Systems and Lube Oil:
Once the particular button for FUEL, COOL WATER, AIR or LUBE OIL is pressed in the MAIN MENU, the accordant overview of FUEL-, COOL WATER-, AIR- or LUBE OIL-VALUES will be displayed.
Example: Overview of Air Values, system without temperature controller.
The overviews FUEL-, COOL WATER-, AIR- and LUBE OIL-VALUES display graphically and on a value basis the pressure (bar/psi) and temperature (°C/F) of these categories by means of bars.
Important note: The following functions are only available on systems with temperature controllers. (T.R.)!
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 60 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
It is possible to go to the following displays via these buttons (1.-5.) in the horizontal navigation bar:
Example for buttons in the navigation bar: Air Systems and System with temperature controller existent:
1. 2. 3. 4.
5.
The temperature can be controlled with following buttons:
The screen pages 1-5, for instance COOLING WATER HT, display the current temperature, the percentage set point and Actual Valve Position.
Durch Drücken den Temperaturwert erhöhen
oder erniedrigen.
Enter set point with the display keyboard that appears after this button was pressed.
Increase or
decrease temperature
By pressing one of these buttons, the displays show the current value and set point (°C/F) . The temperature sequence during a certain period is indicated by a graph.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 61 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3. Media Overview
The function of MEDIA OVERVIEW is to display current measured values of media on three screen pages.
Media Overview Page1 (see below):
- Fuel Values
- Air - Values
- Cooling Water - Values
- Lube Oil - Values
How to display the screen pages Media Overview:
Media Overview (page1 of 3 in total)
Media Overview Page 2:
Charge Air System
Media Overview Page 3:
- Power
- Generator Temperatures
- Gearbox Values
- Service Tank
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 62 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4. Engine Status
The overview ENGINE STATUS lists consecutively the occurred status messages about the engine.
How to display the Engine Status:
Engine Status (page1 of 2) with examples of message
Press the button ENGINE STATUS in the MAIN MENU. List 1(of 2 in total) will be displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 63 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
5. Engine Attached Equipment
The overview ENGINE ATTACHED EQUIPMENT lists the equipment that is attached to the engine.
How to display the Engine Attached Equipment:
Engine attached equipment (page 1 of 2)
6. Confirm Engine Start / Stop
(see also chapters 4.4. Engine Start and 4.7 Engine Stop.)
How to Start or Stop the Engine:
Coloured circles mark the current condition of the particular equipment on this screen page. Please see page 14 for the meaning of different colours.
This button is only activated if an authorised operation is permitted. Press the button ENGINE START / STOP in the MAIN MENU. The menu ENGINE START / STOP SEQUENCE will be displayed.
The messages in this picture show that the start is blocked. The start blockings can be displayed with the active button SHOW BLOCKINGS. A current alarm appeared.
In the menu the following functions are available by means of the six different buttons displayed. Yet only the buttons with black font are active.
(In this example the buttons SHOW BLOCKINGS and ACKNOWLEDGE ENGINE MANUALLYTURNED are active.)
Press the button ENGINE ATTACHED EQUIPMENT in the MAIN MENU. Overview 1 (of 2 in total) will be displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 64 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
How to Show Start Blockings and Failures:
List 1 (of 2 in total) START BLOCKING / FAILURE will be displayed.
Press the button SHOW BLOCKINGS or: Press the button START- BLOCKINGS and FAILURES in the navigation bar.
The button navigation bar marked by the red circle in the allows the following function:
Only if an authorised operation is given, the
function going to the menu ENGINE START /
STOP is active.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 65 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
7. Manual Operations
How to conduct Manual Operations:
In these pictures the pumps are inactive and no lamp test is proceeding.
Example V-Engine
Example L-Engine
Press the button MANUAL OPERATIONS in the MAIN MENU. The menu CYLINDER LUBRICATION CONTROL/… will be displayed.
Important note: Contents within the field of information depends on the engine’s version (V-Engine, L-Engine).
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 66 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
The above displayed menu provides the following functions for Cylinder Lubrication:
Important note: following functions are only available if the engine is shutdown.
To activate or deactivate manual cylinder lubrication, press the button
CYLINDER LUBRICATION MANUALLY – ON / OFF.
Important note: following functions are only available with an operating condition from at least 50% filling:
To change the cylinder lubrication into automatic-mode, press the button
AUTOMATIC-MODE.
Important note: the following function describes the operating condition since the engine’s start
To change the cylinder lubrication into Run In – Modus, press the button
RUN IN- MODE.
Important note: the following button is not visible any longer after the engine was manually turned:
To acknowledge this process, press the button
ACKNOWLEDGE ENGINE MANUALLY TURNED.
display structure if it was manually turned: example for V-Engine
carrying out lamp tests
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 67 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Reset clutch blockings and failures after they
have been corrected.
8. Clutch Control
How to operate the Clutch Control:
How to display Clutch Blockings and Failures:
3.3.3.3.2 Menu Diverse
Menu Diverse - Overview
Confirm the chosen process (engaged or disengaged).
Press the button SHOW BLOCKINGS.
or: Press the button CLUTCH-/BLOCKINGS and FAILURES in the navigation bar.
Important note: This function is optional. Press the button CLUTCH CONTROL in the Main Menu. The menu CLUTCH CONTROL will be displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 68 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3.3.3.3.5 Menu Diverse
Menu Diverse- Overview
I. Structure ........................................................................................................................ 69
II. Functions ..................................................................................................................... 70
1. Adjusting Time and Date ............................................................................................. 70
2. Display – Diagnostic ................................................................................................... 72
3. Display – Technical Specification .............................................................................. 73
4. Display – Adjust Backlight .......................................................................................... 73
5. Software – Information ................................................................................................ 74
6. IMO-VIT Parameters .................................................................................................... 75
7. Redundant Values ....................................................................................................... 76
8. Start - Blockings and Failures (optional) ................................................................... 77
9. Clutch Blockings and Failures (optional) .................................................................. 78
10. Turbine Disc-Cooling (optional) ................................................................................. 79
11. PLC-Diagnostic ............................................................................................................ 80
12. Using the Histogram ................................................................................................... 80
13. Selecting a Language and Adjusting Dimension Units ............................................ 81
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 69 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
I. Structure
Cut line
1: Headline 4: Field of Alarms
2: Status Line 5: Navigation Bar
3: Field of Information (see next page)
3: Field of Information
Within the field of information, there are the following buttons to go to different screen pages.
• Password
• Display diagnostic
• Display Technical Specification
• Display Backlight Control
• Project Info
• IMO-VIT Parameters
• Redundant Values
• PLC-Diagnostic
• Histogram
• Select Language
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 70 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Optional Functions
• Start Blockings and Failures
• Clutch Blockings and Failures
• Turbine Disc-Cooling. Functions
• Trend
• Recipe
II. Functions
The submenu DIVERSE provides special functions.
How the Menu Diverse can be accessed:
1. Adjusting Time and Date
How to use Password Protected Functions
The only permitted password protected function is adjusting date and time that appear on the screen.
1. Request password from service. 2. Please press the button PASSWORT in the menu DIVERSE.
The screen page SECURITY PASSWORD appears immediately.
Press the button DIVERSE in the MAIN MENU. or: Press this button on any screen page where it is displayed alternatively.
Once this button is pressed, the menu DIVERSE will be displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 71 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Security Passwords
3. Press the Time/Date-field and the displayed keyboard shows up to ask for the password.
4. Enter the password via the displayed keyboard.
5. Confirm entry with the enter key. Date and time will appear.
6. Change date and time via the displayed keyboard. The correct order of the entry is:
year-month-day hours:minutes:seconds
7. Confirm entry with the enter key. Displayed keyboard will disappear and the adjustment is saved. Button in the navigation bar on the page “Security Passwords”:
Important note: This button is password protected. Access only for service staff.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 72 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
2. Display – Diagnostic
This function displays following information on the display:
• Type of display
• Size of display
• Space of free dynamic memory
• Space of used flash memory
• Firmware version of display
• IP-Address of display
• Temperature values of colours
How to show the page DISPLAY DIAGNOSTIC:
Part from the Display Diagnostic
Within the menu DIVERSE, press the Button DISPLAY DIAGNOSTIC to show a screen page with current display data.
To leave the page DISPLAY DIAGNOSTIC, please touch the screen and the menu DIVERSE will be displayed again.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 73 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
3. Display – Technical Specification
The display TECHNICAL SPECIFICATION lists general technical data of the display.
How to show Technical Specification of the Display:
4. Display – Adjust Backlight
How to adjust the backlight of the display:
Press the button DISPLAY TECHNICAL SPECIFICATION in
the menu DIVERSE to show a screen page with general technical specification.
1. Press the button DISPLAY BACKLIGHT CONTROL in the menu DIVERSE.
Display with slide switch and a test-photo appears.
2. Adjust the lightness of the display with the slide switch:
0: maximum lightness 50: minimum lightness The adjustment will be saved automatically.
Technical Specification (without any data)
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 74 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
5. Software – Information
Following specific information on applications can be seen on the screen page PROJEKT INFO:
- Display-Software Version
- Single PLC software versions
- Application (marine or stationary)
- Date of setting the parameters
- Type of engine
- Number of cylinder
- Number of engine
How to show Information on the Software:
Project Info, example – engine with all systems
Press the button PROJECT INFO in the menu DIVERSE.
A page with current information on software will show up.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 75 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
6. IMO-VIT Parameters
The display IMO Parameters shows the engine- and system-specific IMO-VIT data.
How to display IMO-VIT-Parameters:
IMO-Parameters, example without electronic injection system.
Press the button IMO-VIT PARAMETER in the menu DIVERSE. Display IMO-PARAMETER will show up.
It is possible to go to the adequate menu via the button in the navigation bar that is marked by the red circle.
This button is only active in case of an existent electronic injection system.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 76 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
7. Redundant Values
The overview REDUNDANT VALUES serves to control and compare redundant sensor values to each other. The sensors are installed pair wise. If the system loses in certain values (sensor error), the system automatically reverts to the second sensor.
How to display Redundant Sensor Values:
Overview 1 Redundant Value
Press the button REDUNDANT VALUES in the menu DIVERSE. Overview 1 (of 2 in total) REDUNDANT VALUES will be displayed.
The overview REDUNDANT VALUES displays the measured sensor values of the pair wise installed sensors.
It is possible to compare these sensor values directly, since they are listed in a chart as the Overview 1 displays on the left.
Meaning of Colour: A red-marked value indicates a sensor blackout and consequently an alarm will be released.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 77 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
8. Start - Blockings and Failures (optional)
How to display Start - Blockings and Failures:
Start-Blockings and Failures, page 1
It is possible to use the following specific functions in the navigation bar.
Important note: This button is only active if authorised operations are permitted Go to the menu ENGINE START/STOP.
Press the button START- BLOCKINGS and FAILURES in the menu DIVERSE.
List 1 (of 2 in total) START- BLOCKINGS and FAILURES with current messages are displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 78 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
9. Clutch Blockings and Failures (optional)
This function is optional and only existent with clutch-controlled engines.
How to display Clutch Blockings and Failures:
Clutch Blockings and Failures (without any data), page1
It is possible to use the following specific functions in the navigation bar.
Important note: The following button is only active if operations are authorised. By pressing this button, go to the menu CLUTCH CONTROL.
Press the button CLUTCH - BLOCKINGS and FAILURES in the menu DIVERSE. List 1 (of 2 in total) CLUTCH - BLOCKINGS and FAILURES with current messages are displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 79 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
10. Turbine Disc-Cooling (optional)
This function is optional and only existent with engines that have turbine disc cooling.
The display TURBINE DISC-COOLING shows the following data relevant for turbine disc cooling:
• Speed TC
• Cooling Air Pressure
• Set point Cooling Air Pressure
• Alarm point Cooling Air Pressure
• Lamp indication for activation of pressure monitoring
How to display the Data of Turbine Disc-Cooling:
Information on Turbine Disc-Cooling
Diagrams indicate the process of data within a certain period of time graphically and on a value basis.
The status display marks the state of pressure which is monitored.
Press the button TURBINE DISC-COOLING in the menu DIVERSE.
Display of TURBINE DISC-COOLING with current messages is displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 80 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
11. PLC-Diagnostic
How to go to the menu PLC-Diagnostic:
12. Using the Histogram
Important note: This function is not yet available.
How the Histogram is displayed:
Press the button PLC-DIAGNOSTIC in the menu DIVERSE.
or:
Press the button PLC-DIAGNOSTIC in the navigation bar of the display PROJECT INFO or ALARM-ERROR CORRECTION.
The menu PLC-DIAGNOSTIC with all its optional functions is displayed immediately afterwards and the following functions give an overview of current data.
Only existent if control is separate.
optional
Please press the button HISTOGRAM in the menu DIVERSE. The screen page HISTOGRAM will appear immediately afterwards.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 81 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
13. Selecting a Language and Adjusting Dimension Units
How to select a Language for the Menus:
Select a language, the current language is English at the moment
How to set dimension units:
Press the button SELECT LANGUAGE in the menu DIVERSE.
The screen page SELECT LANGUAGE will appear subsequently.
Corresponding to the flags, the following languages can be selected:
German, English, Spanish, Portuguese.
Press the button with the favourite language
The chosen language will be displayed in the box.
The chosen language will be saved automatically.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 82 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Data can be displayed in two different dimension units. The translation is carried out automatically.
3.4 System Integration
3.4.1 System Outline SaCoS is connected with the ship’s installations by several different interfaces.
3.4.2 Alarm System A MODBUS interface serves as connection to the machinery alarm system. The ship’s machinery system (master system) periodically requests for data, which are then sent to the alarm system by SaCoS (slave system). The available data are listed in the chapter “Interfaces” of the engine automation manual.
3.4.3 Propeller The interface includes safety and remote control functions. The safety functions control all interconnections between main engine and propulsion control system (PCS), according to classification and MAN Diesel requirements. The remote control functions are available as long as “remote control” is selected at the local engine control panel. In remote control, a main engine start and stop, as well as a pre-selection of the engine speed set point, is available from the PCS. For details, please refer to chapter “Interfaces” of the engine automation manual.
3.4.4 Pump Control The interface to the pump control system is designed as a hardwired interface. SaCoS requests lubrication and cooling by means of pumps if a pump operation is necessary.
Chose the desired dimension unit by means of the slide switch. The slide switch is red if the dimension unit "bar °C" is chosen (this example shows that "bar °C" was set).
The slide switch is green if the dimension unit "psi °F" is chosen.
The chosen dimension unit will be saved automatically.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 83 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
The starters for the pumps and the local / remote operation handling are carried out by the pump control system. For details, please refer to the chapter “Interfaces” of the engine automation manual and to the documents concerning the pump control system.
3.4.5 Clutch Operation The engine’s traction system is not equipped with automatic clutches.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 84 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4 Operation / Control
4.1 Operating Hierarchy / Control Station The Control Station on engine is the preferential Control Panel for emergency operation. If Local-/Remote switch on Control Station on engine is in position local, there is no operation from any other SaCoS-Panel possible.
4.1.1 Regular Operation (Remote) Regular operation is controlled at the SaCoS operating panel, which normally is installed in the engine control room. Engine start, error acknowledgements as well as the indication of all messages about status, operation and errors are carried out here. In this operating mode, the speed set point target is set by the propeller control.
4.1.2 External Control The propeller control regulates the engine start / stop and target speed set point. The detailed indication of messages concerning status, operations and errors is available at the SaCoS operating panel.
4.1.3 Emergency Operation (Local) An emergency operation can only be carried out locally at the control station on engine. Engine start and speed setting are possible even if SaCoS is not available.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 85 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.2 Engine Startup In case the engine has been put out of operation due to, e.g., longer works of maintenance and repair, it has to be preheated and pre-lubricated sufficiently before being started again.
Conservations, which were made, have to be removed if necessary. For more information on this, please refer to the correspondent chapters in the engine manuals and the necessary auxiliary systems. If the power supplies of SaCoS are being interrupted, they have to be switched on early enough before the engine is started, to assure that possibly existing rechargeable batteries can be reloaded and are available with full capacity. For further information regarding batteries please refer to the separate manual of the auxiliary cabinet.
System Test
When the power supply is switched on, SaCoS starts automatically after a self-test. As soon as the starting procedure is completed, all upcoming error messages on the operating panel must be acknowledged and reset. Please check all temperatures, pressures and other measured values for plausibility and correct all reasons for further error messages occurring.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 86 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.3 Starting Preparations
STARTING CONDITIONS
If one or more of the criteria listed below are not achieved, the engine cannot be started and the start-up procedure will be blocked. An error message appears at the text display, indicating that start interlocks are active. The operator can call up the list of these criteria on the text display by pressing the button SHOW START BLOCKINGS.
TURNING GEAR NOT ENGAGED Signal from limit switch Signal = 1 TURNING GEAR ENGAGED
STOP BY SAFETY SYSTEM NOT ACTIVE Signal = 1 STOP BY SAFETY SYSTEM
ACTIVE
EMERGENCY STOP NOT ACTIVE Signal = 1 EMERGENCY STOP ACT IVE
REMOTE STOP SEQUENCE NOT RUNNING ( engine standstill ) Signal = 1 REMOTE STOP SEQUENCE
RUNNING
SELECTOR SWITCH ON ENGINE IN POS . „REMOTE CONTROL“
Signal = 1
REMOTE CONTROL OFF
SELECTOR SWITCH ON ENGINE IN POS . „ELECTRON . GOVERNOR“
MECHANICAL GOVERNOR SELECTED
START RELEASE FROM CPP CONTROL ( pitch = zero or clutch disengaged )
Signal = 1
NO START RELEASE FROM CPP CONTROL
Signal = 1
TEXT DISPLAY OF ENGINE CONTROL ROOM PANEL
no
yes
no
yes
no
yes
no
yes
no
yes
no
yes
no
yes
no
yes
ENGINE START BLOCKED Result = 1
ENGINE STOPPED PRESS
<START>
TO START ENGINE
A
TURNING GEAR ENGAGED
DON’T START
A
CONTROL STATION ON ENGINE
Result = 1
yes
B
B
no
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 87 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
If one of the starting conditions is not provided, the indicator lamp “DON’T START” lights up
in the control station on engine.
The engine can be started by actuating the 3/2-way valve in spite of the indication “DON’T
START” (Emergency start with operator’s personal responsibility), except if the turning
gear is engaged. In case the turning gear is engaged, the engine start is blocked
pneumatically. A turning gear, which is engaged, is indicated at the control station on the
engine, too.
4.4 Engine Start Before starting the engine, several settings are to be carried out depending on the implemented speed control system. If the engine is to be started with the mechanical speed governor, the speed set point must be adjusted to “minimum speed set point” before starting. In case this set point is not adjusted, over speed can occur after starting the engine. If the engine is to be started with the electronic speed governor, the speed set point must be adjusted to “maximum speed set point” before starting the engine. If this set point is not adjusted, the full nominal speed will not be reached during engine operation. The control lamps at the local operating stand indicate whether these set points have been reached or not.
4.4.1 Local Start The local start will be triggered by pressing the “START” button (1) at the engine-mounted control station until the engine starts running.
4.4.2 Remote Start The regular engine start is carried out from the engine control room with electrical speed control. In order to use the full speed range of the engine, the speed set point of the mechanical governor is to be set on “maximum speed”. This can be done directly at the speed governor or at one of the SaCoS cabinets. The engine can be started by pressing the start key on the engine-operating panel in the engine control room if the starting conditions have been met, i.e. no start interlock should be active. During the start procedure, the operator can follow the individual steps on the display of the engine-operating panel. In case of an error occurring during engine start, all the signals and devices activated previously will be deactivated or switched off. The engine starting procedure can be re-attempted if the error has been deleted and if the operator has acknowledged.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 88 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Confirm Engine Start / Stop in the Main Menu
How to Start or Stop the Engine:
The messages in the picture above show that the start is blocked. The start blockings can be displayed with the active button SHOW BLOCKINGS to display the current alarm.
In the menu the following functions are available by means of the buttons displayed. Yet only the following buttons are active accordant to a message:
START
STOP
RESET
SHOW BLOCKINGS
CONFIRMATION
ACKNOWLEDGE ENGINE MANUALLY TURNED
If the engine is running, please press the accordant button to stop the engine. The corresponding messages are shown on the display
This button is only activated if an authorised operation is permitted. Press the button ENGINE START / STOP in the Main Menu. The menu ENGINE START / STOP SEQUENCE will be displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 89 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Remote Start Sequence:
Timer t 1 for start confirmation starts
Remote start key < Start > pressed ?
PRESS < Comf. > TO CONFIRM
TEXT DISPLAY OF ENGINE CONTROL ROOM PANEL
no
yes
PRESSURE FORMATION
ENGINE STOPPED PRESS < Start > TO START ENGINE
t 1 = 10 sec .
key < Conf. > pressed ?
no
yes t 1 completed ?
no
yes
Start sequence aborted
Request to start engine luboil pump
Request to s tart cooling water pump
Request to start gear box luboil pump
Timer t 2 for pump monitoring starts t 2 = 2 min .
Engine luboil press . > 0 , 6 bar ?
t 2 completed ?
Turboch . luboil press . > 0 , 5 bar ?
t 2 completed ?
Gear box luboil press . available ?
t 2 completed ?
HT cooling water press . > 2 bar ?
t 2 completed ?
yes yes
yes
yes yes
no
no no
no
yes
yes no
no
no no
yes
A A
&
a
d c
b see page 85
see page 85
see page 85
see page 85
to page 84
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 90 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Engine prelubrication
Start without prelubrication
possible ?
PRELUBRICATION RUNNING
TEXT DISPLAY OF ENGINE CONTROL ROOM PANEL
no
yes
START AIR RELEASED
t 6 = 8 sec .
no
yes
t 5 completed ?
A
Timer t 5 for prelubrication starts
Standstill time < 30 min .
t 5 = 1 min .
Starting valve actuated
no Engine speed > ignition speed
Timer t 6 for ignition time monitoring starts
yes
yes
no t 6 completed ?
t 7 = 20 sec .
yes
Starting valve deactuated
no Engine speed > 200 rpm
Timer t 7 for start monitoring starts
yes
yes
no t 7 completed ?
ENGINE IS STARTING
ENGINE IS RUNNING
yes
yes
no Engine speed > pump st . by speed ?
Req uest for operation of luboil pumps and cooling water pump deleted
e see page 85
f see page 85
Starting valve deactuated
yes
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 91 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.4.3 Emergency Start The emergency start and the emergency stop from the engine operating panel are independent from the local / remote switch. Local start / stop as emergency actuation must be always possible.
Once the START push button is pressed, an emergency start will be performed without prior monitoring of oil pressures or engine priming. The starting procedure is performed manually without any action of the engine control system. The starting valve is activated as long as the operator is keeping the START button pressed. The valve must be actuated until the engine is turning independently and the engine speed is higher than the start speed (approx. 85 rpm).
It has to be cancelled if an emergency stop valve is activated. During an emergency start, no automatic start backup control is available.
Engine operators take the full responsibility for triggering an emergency start! Prior to triggering an emergency start, the cooling water and lubricating oil pumps must be switched on manually by the operator.
Start sequence aborted
STARTING FAILURE
TEXT DISPLAY OF ENGINE CONTROL ROOM PANEL
START FAILURE : PRELUB PRESS . ENGINE LOW
f a b c d e
START FAILURE : MINIMUM SPEED NOT REACHED
START FAILURE : START SPEED NOT REACHED
START FAILURE : COOLING WATER PRESS . LOW
START FAILURE : PRELUB PRESS . GEAR LOW
START FAILURE : PRELUB PRESS . TC LOW
> = 1
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 92 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.5 Abnormal Conditions and Failure Messages
Index Message Text
3000 10500 -SD: ENGINE LUBOIL PRESS. LOW:
3001 10501 -OVRD SD: ENGINE LUBOIL PRESS. LOW:
3002 10502 -SD: HT CW PRESS. LOW SET:
3003 10503 -OVRD SD: HT CW PRESS. LOW SET:
3004 10504 -SD: TC LUBOIL PRESS. LOW SET:
3005 10505 -OVRD SD: TC LUBOIL PRESS. LOW SET:
3006 10506 -SD: GEARBOX LUBOIL PRESS. LOW:
3007 10507 -OVRD SD: GEARBOX LUBOIL PRESS. LOW:
3008 10508 -SD: TC LUBOIL TEMP. HIGH:
3009 10509 -OVRD SD: TC LUBOIL TEMP. HIGH:
3010 10510 -SD: TC B LUBOIL TEMP. HIGH:
3011 10511 -OVRD SD: TC B LUBOIL TEMP. HIGH:
3012 10512 -SD: ENGINE OVERSPEED PLC-SYSTEM SET:
3014 10514 -SD: ENGINE LUBOIL TEMP. HIGH SET:
3015 10515 -OVRD SD: ENGINE LUBOIL TEMP. HIGH SET:
3016 10516 -SD: HT COOL. WATER TEMP.HIGH SET:
3017 10517 -OVRD SD: HT COOL.WATER TEMP.HIGH SET:
3018 10518 -SD: EMERGENCY STOP AIR PRESS. LOW SET:
3020 10520 -SD: OILSUMPLEVEL TOO HIGH SET:
3021 10521 -OVRD SD: OILSUMPLEVEL TOO HIGH SET:
3022 10522 -SD: OILSUMPLEVEL TOO LOW SET:
3023 10523 -OVRD SD: OILSUMPLEVEL TOO LOW SET:
3024 10524 -SD: GENER. BEARING TEMP. NDE HIGH SET:
3026 10526 -SD: GENER. BEARING TEMP. DE HIGH SET:
3028 10528 -SD: GENER. WINDING TEMP. L1 HIGH SET:
3030 10530 -SD: GENER. WINDING TEMP. L2 HIGH SET:
3032 10532 -SD: GENER. WINDING TEMP. L3 HIGH SET:
3034 10534 -SD: FUEL OIL PRESS. LOW SET:
3036 10536 -SD: TC SPEED HIGH SET:
3037 10537 -OVRD SD: TC SPEED HIGH SET:
3038 10538 -SD: TC B SPEED HIGH SET:
3039 10539 -OVRD SD: TC B SPEED HIGH SET:
3048 10548 -SD: EMERGENCY SHUTDOWN ACTIVE
3049 10549 -SD: EMERGENCY SHUTDOWN ENGINE OPERATING PANEL
3050 10550 -SD: EMERGENCY SHUTDOWN SaCoS PANEL
3051 10551 -SD: EMERGENCY SHUTDOWN WHEELHOUSE
3052 10552 -SD: EMERGENCY SHUTDOWN ON ENGINE
3053 10553 -SD: EMERGENCY SHUTDOWN spare 1
3054 10554 -SD: OVERSPEED ENGINE (SENSOR 1)
3055 10555 -SD: OVERSPEED ENGINE (SENSOR 2)
3056 10556 -SD: OILMIST DETECTOR
3057 10557 -OVRD SD: OILMIST DETECTOR
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 93 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3058 10558 -SD: ENGINE LUBOIL PRESS. SWITCH
3059 10559 - OVRD SD: ENGINE LUBOIL PRESS. SWITCH
3060 10560 -SD: GEARBOX LUBOIL PRESS. SWITCH
3061 10561 -OVRD SD: GEARBOX LUBOIL PRESS. SWITCH
3062 10562 -SD: GEARBOX LUBOIL PRESS. LOW
3063 10563 -OVRD SD: GEARBOX LUBOIL PRESS. LOW
3064 10564 -SD: EM-DRIVER FAILURE
3065 10565 -OVRD SD: EM-DRIVER FAILURE
3066 10566 -SD: GENERATOR DISTURBANCE
3067 10567 -OVRD SD: GENERATOR DISTURBANCE
3068 10568 -SD: HT CW TEMP. HIGH
3069 10569 -OVRD SD: HT COOL.WATER TEMP. HIGH
3070 10570 -SD: LUBOIL AUTOMATIC FILTER
3071 10571 -SD: EMERGENCY SHUTDOWN AUXILIARY CABINET
3072 10572 -SD: LUBOIL INDICATOR FILTER
3074 10574 -SD: HFO-MODULE DISTURBANCE
3075 10575 -OVRD SD: HFO-MODULE DISTURBANCE
3076 10576 -SD: THERMAL OIL SYSTEM DISTURBANCE
3077 10577 -OVRD SD: THERMAL OIL SYSTEM DISTURBANCE
3078 10578 -SD: EXH. GAS BOILER DISTURBANCE
3079 10579 -OVRD SD: EXH. GAS BOILER DISTURBANCE
3080 10580 -SD: TRANSFORMER FAILURE
3081 10581 -SD: UPS BATTERY LOAD-LEVEL LOW
3082 10582 -SD: GENERATOR EXCITATION FAILURE
3083 10583 -SD: UPS-OPERATION TIME ELAPSED (approx. 20 min.)
3084 10584 -SD: GENERATOR WINDING TEMP. HIGH
3085 10585 -SD: MAJOR ALARM ELECTRONIC SPEED GOVERNOR
3086 10586 -SD: TOTAL LOSS OF SENSORS 1/2 SE1000 ENGINE SPEED
3087 10587 -SD: TOTAL LOSS OF OVERSPEED PROTECTION
3088 10588 -SD: TOTAL LOSS OF SENSORS 1/2 PT2170 LUBOIL PRESS. ENGINE
3089 10589 -SD: TOTAL LOSS OF SENSORS 1/2 TE2170 LUBOIL TEMP. ENGINE
3090 10590 -SD: TOTAL LOSS OF SENSORS 1/2 PT2570 LUBOIL PRESS. TC
3091 10591 -SD: TOTAL LOSS OF SENSORS 1/2 TE2580A LUBOIL TEMP. TC
3092 10592 -SD: TOTAL LOSS OF SENSORS 1/2 TE2580B LUBOIL TEMP. TC B
3093 10593 -SD: TOTAL LOSS OF SENSORS 1/2 PT3170 HT CW PRESS.
3094 10594 -SD: TOTAL LOSS OF SENSORS 1/2 TE3180 HT CW TEMP. ENGINE
3096 10596 -SD: GEARBOX BEARING TEMP. PINION SHAFT 2TSZH2971
3097 10597 -OVRD SD: GEARBOX BEARING TEMP. PINION SHAFT 2TSZH2971
3098 10598 -SD: GEARBOX BEARING TEMP. OUTPUT SHAFT 2TSZH2972
3099 10599 -OVRD SD: GEARBOX BEARING TEMP. OUTPUT SHAFT 2TSZH2972
3100 10600 -SD: GEARBOX BEARING TEMP. PTO SHAFT 2TSZH2973
3101 10601 -OVRD SD: GEARBOX BEARING TEMP. PTO SHAFT 2TSZH2973
3102 10602 -SD: GEARBOX AXIAL BEARING TEMP. PINION SHAFT 2TSZH2974
3103 10603 -OVRD SD: GEARBOX AXIAL BEAR. TEMP. PINION SHAFT 2TSZH2974
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 94 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3110 10610 -SD: FAILURE EMERGENCY STOP VALVE
3111 10611 -OVRD SD: FAILURE EMERGENCY STOP VALVE
3112 10612 -SD: MAIN BEARING TEMP. HIGH -BEARING: 01
3113 10613 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 01
3114 10614 -SD: MAIN BEARING TEMP. HIGH -BEARING: 1
3115 10615 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 1
3116 10616 -SD: MAIN BEARING TEMP. HIGH -BEARING: 2
3117 10617 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 2
3118 10618 -SD: MAIN BEARING TEMP. HIGH -BEARING: 3
3119 10619 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 3
3120 10620 -SD: MAIN BEARING TEMP. HIGH -BEARING: 4
3121 10621 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 4
3122 10622 -SD: MAIN BEARING TEMP. HIGH -BEARING: 5
3123 10623 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 5
3124 10624 -SD: MAIN BEARING TEMP. HIGH -BEARING: 6
3125 10625 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 6
3126 10626 -SD: MAIN BEARING TEMP. HIGH -BEARING: 7
3127 10627 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 7
3128 10628 -SD: MAIN BEARING TEMP. HIGH -BEARING: 8
3129 10629 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 8
3130 10630 -SD: MAIN BEARING TEMP. HIGH -BEARING: 9
3131 10631 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 9
3132 10632 -SD: MAIN BEARING TEMP. HIGH -BEARING: 10
3133 10633 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 10
3134 10634 -SD: MAIN BEARING TEMP. HIGH -BEARING: 11
3135 10635 -OVRD SD: MAIN BEARING TEMP. HIGH -BEARING: 11
3160 10660 -SD: SPLASH OIL TEMP. MAX. -COMP.: 1
3161 10661 -OVRD SD: SPLASH OIL TEMP. MAX. -COMP.: 1
3162 10662 -SD: SPLASH OIL TEMP. MAX. -COMP.: 2
3163 10663 -OVRD SD: SPLASH OIL TEMP. MAX. -COMP.: 2
3164 10664 -SD: SPLASH OIL TEMP. MAX. -COMP.: 3
3165 10665 -OVRD SD: SPLASH OIL TEMP. MAX. -COMP.: 3
3166 10666 -SD: SPLASH OIL TEMP. MAX. -COMP.: 4
3167 10667 -OVRD SD: SPLASH OIL TEMP. MAX. -COMP.: 4
3168 10668 -SD: SPLASH OIL TEMP. MAX. -COMP.: 5
3169 10669 -OVRD SD: SPLASH OIL TEMP. MAX. -COMP.: 5
3170 10670 -SD: SPLASH OIL TEMP. MAX. -COMP.: 6
3171 10671 -OVRD SD: SPLASH OIL TEMP. MAX. -COMP.: 6
3172 10672 -SD: SPLASH OIL TEMP. MAX. -COMP.: 7
3173 10673 -OVRD SD: SPLASH OIL TEMP. MAX. -COMP.: 7
3174 10674 -SD: SPLASH OIL TEMP. MAX. -COMP.: 8
3175 10675 -OVRD SD: SPLASH OIL TEMP. MAX. -COMP.: 8
3176 10676 -SD: SPLASH OIL TEMP. MAX. -COMP.: 9
3177 10677 -OVRD SD: SPLASH OIL TEMP. MAX. -COMP.: 9
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 95 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3178 10678 -SD: SPLASH OIL TEMP. MAX. -COMP.: 10
3179 10679 -OVRD SD: SPLASH OIL TEMP. MAX. -COMP.: 10
3180 10680 -SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 1
3181 10681 -OVRD SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 1
3182 10682 -SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 2
3183 10683 -OVRD SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 2
3184 10684 -SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 3
3185 10685 -OVRD SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 3
3186 10686 -SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 4
3187 10687 -OVRD SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 4
3188 10688 -SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 5
3189 10689 -OVRD SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 5
3190 10690 -SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 6
3191 10691 -OVRD SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 6
3192 10692 -SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 7
3193 10693 -OVRD SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 7
3194 10694 -SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 8
3195 10695 -OVRD SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 8
3196 10696 -SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 9
3197 10697 -OVRD SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 9
3198 10698 -SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 10
3199 10699 -OVRD SD: SPLASH OIL TEMP. MVD HIGH -COMP.: 10
3240 10740 -SD: EXH. GAS TEMP. HIGH -CYL.: A 1
3241 10741 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: A 1
3242 10742 -SD: EXH. GAS TEMP. HIGH -CYL.: A 2
3243 10743 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: A 2
3244 10744 -SD: EXH. GAS TEMP. HIGH -CYL.: A 3
3245 10745 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: A 3
3246 10746 -SD: EXH. GAS TEMP. HIGH -CYL.: A 4
3247 10747 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: A 4
3248 10748 -SD: EXH. GAS TEMP. HIGH -CYL.: A 5
3249 10749 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: A 5
3250 10750 -SD: EXH. GAS TEMP. HIGH -CYL.: A 6
3251 10751 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: A 6
3252 10752 -SD: EXH. GAS TEMP. HIGH -CYL.: A 7
3253 10753 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: A 7
3254 10754 -SD: EXH. GAS TEMP. HIGH -CYL.: A 8
3255 10755 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: A 8
3256 10756 -SD: EXH. GAS TEMP. HIGH -CYL.: A 9
3257 10757 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: A 9
3258 10758 -SD: EXH. GAS TEMP. HIGH -CYL.: A 10
3259 10759 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: A 10
3260 10760 -SD: EXH. GAS TEMP. HIGH BEF. TC A
3261 10761 -OVRD SD: EXH. GAS TEMP. HIGH BEF. TC A
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 96 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3264 10764 -SD: EXH. GAS TEMP. HIGH -CYL.: B 1
3265 10765 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: B 1
3266 10766 -SD: EXH. GAS TEMP. HIGH -CYL.: B 2
3267 10767 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: B 2
3268 10768 -SD: EXH. GAS TEMP. HIGH -CYL.: B 3
3269 10769 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: B 3
3270 10770 -SD: EXH. GAS TEMP. HIGH -CYL.: B 4
3271 10771 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: B 4
3272 10772 -SD: EXH. GAS TEMP. HIGH -CYL.: B 5
3273 10773 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: B 5
3274 10774 -SD: EXH. GAS TEMP. HIGH -CYL.: B 6
3275 10775 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: B 6
3276 10776 -SD: EXH. GAS TEMP. HIGH -CYL.: B 7
3277 10777 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: B 7
3278 10778 -SD: EXH. GAS TEMP. HIGH -CYL.: B 8
3279 10779 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: B 8
3280 10780 -SD: EXH. GAS TEMP. HIGH -CYL.: B 9
3281 10781 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: B 9
3282 10782 -SD: EXH. GAS TEMP. HIGH -CYL.: B 10
3283 10783 -OVRD SD: EXH. GAS TEMP. HIGH -CYL.: B 10
3284 10784 -SD: EXH. GAS TEMP. HIGH BEF. TC B
3285 10785 -OVRD SD: EXH. GAS TEMP. HIGH BEF. TC B
3288 10788 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 1
3289 10789 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 1
3290 10790 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 2
3291 10791 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 2
3292 10792 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 3
3293 10793 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 3
3294 10794 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 4
3295 10795 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 4
3296 10796 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 5
3297 10797 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 5
3298 10798 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 6
3299 10799 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 6
3300 10800 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 7
3301 10801 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 7
3302 10802 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 8
3303 10803 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 8
3304 10804 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 9
3305 10805 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 9
3306 10806 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 10
3307 10807 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: A 10
3308 10808 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 1
3309 10809 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 1
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 97 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3310 10810 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 2
3311 10811 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 2
3312 10812 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 3
3313 10813 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 3
3314 10814 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 4
3315 10815 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 4
3316 10816 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 5
3317 10817 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 5
3318 10818 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 6
3319 10819 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 6
3320 10820 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 7
3321 10821 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 7
3322 10822 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 8
3323 10823 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 8
3324 10824 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 9
3325 10825 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 9
3326 10826 -SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 10
3327 10827 -OVRD SD: EXH. GAS TEMP. MVD HIGH -CYL.: B 10
3368 10868 -SD: GENERATOR 1 FAILURE
3369 10869 -SD: GENERATOR 2 FAILURE
3384 10884 -SD: KNOCKING CYLINDER A1
3385 10885 -SD: KNOCKING CYLINDER A2
3386 10886 -SD: KNOCKING CYLINDER A3
3387 10887 -SD: KNOCKING CYLINDER A4
3388 10888 -SD: KNOCKING CYLINDER A5
3389 10889 -SD: KNOCKING CYLINDER A6
3390 10890 -SD: KNOCKING CYLINDER A7
3391 10891 -SD: KNOCKING CYLINDER A8
3392 10892 -SD: KNOCKING CYLINDER A9
3393 10893 -SD: KNOCKING CYLINDER A10
3394 10894 -SD: KNOCKING CYLINDER B1
3395 10895 -SD: KNOCKING CYLINDER B2
3396 10896 -SD: KNOCKING CYLINDER B3
3397 10897 -SD: KNOCKING CYLINDER B4
3398 10898 -SD: KNOCKING CYLINDER B5
3399 10899 -SD: KNOCKING CYLINDER B6
3400 10900 -SD: KNOCKING CYLINDER B7
3401 10901 -SD: KNOCKING CYLINDER B8
3402 10902 -SD: KNOCKING CYLINDER B9
3403 10903 -SD: KNOCKING CYLINDER B10
3409 10909 -SD: ENGINE OVERLOAD
3410 10910 -SD: ENGINE OVERLOAD INTEGRATOR
3411 10911 -SD: GAS PRESS. GAS LINE INLET LOW
3412 10912 -SD: IGNITION GAS PRESS. BEF. ENGINE LOW
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 98 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3413 10913 -SD: IGNITION GAS PRESS. BEF. ENGINE HIGH
3414 10914 -SD: IGNITION GAS LEAKAGE PRESS. HIGH
3415 10915 -SD: START AIR PRESS. LOW
3416 10916 -SD: EMERGENCY STOP GENERATOR CONTROL
3417 10917 -SD: EMERGENCY STOP POWER SUPPLY CABINET
3418 10918 -SD: EMERGENCY STOP GAS SOLENOID VALVE
3419 10919 -SD: EMERGENCY STOP MCC
3421 10921 -SD: MAJOR ALARM INPULSE IGNITION
3422 10922 -SD: MAJOR ALARM INPULSE SOGAV
3423 10923 -SD: ETHERNET COMMUNICATION FAILURE
3424 10924 -SD: GLOW PLUG FAILURE
3425 10925 -SD: TOTAL LOSS OF SENSORS
3426 10926 -SD: SAFETY VALVE GAS LINE ACTIVATED
3427 10927 -SD: CAN BUS FAILURE
3428 10928 -SD: POWER MONITORING
3429 10929 -SD: GENERATOR PROTECTION
3430 10930 -SD: MEDIUM VOLTAGE CIRCUIT BREAKER
3431 10931 -SD: GENERATOR LUBRICATION
3432 10932 -RED.: ENGINE LUBOIL PRESS. LOW SET:
3433 10933 -OVRD RED.: ENGINE LUBOIL PRESS. LOW SET:
3434 10934 -RED.: HT CW PRESS. LOW SET:
3435 10935 -OVRD RED.: HT CW PRESS. LOW SET:
3436 10936 -RED.: ENGINE LUBOIL TEMP. HIGH SET:
3437 10937 -OVRD RED.: ENG.LUBOIL TEMP.HIGH SET:
3438 10938 -RED.: HT CW TEMP. HIGH SET:
3439 10939 -OVRD RED.: HT CW TEMP. HIGH SET:
3440 10940 -RED.: TC SPEED HIGH SET:
3441 10941 -OVRD RED.: TC SPEED HIGH SET:
3442 10942 -RED.: TC B SPEED HIGH SET:
3443 10943 -OVRD RED.: TC B SPEED HIGH SET:
3444 10944 -RED.: GEARBOX LUBOIL TEMP. HIGH SET:
3445 10945 -OVRD RED.: G.BOX LUB.TEMP.HIGH SET:
3446 10946 -RED.: THRUST BEARING TEMP. HIGH SET:
3447 10947 -OVRD RED.: THR.BEAR.TEMP.HIGH SET:
3448 10948 -RED.: GEAR PINION SHAFT TEMP.HIGH SET:
3449 10949 -OVRD RED.: G.PIN.SHAFT TEMP.HIGH SET:
3450 10950 -RED.: GEAR OUTP.SHAFT TEMP.HIGH SET:
3451 10951 -OVRD RED.: G.OUTP.SHAFT TEMP.HIGH SET:
3464 10964 -RED.: CHARGE AIR BLOW OFF FUNCTION ERROR
3465 10965 -OVRD RED.: CHARGE AIR BLOW OFF FUNCTION ERROR
3466 10966 -RED.: LUBOIL AUTOMATIC FILTER DIFF.PRESS. HIGH
3467 10967 -OVRD RED.: LUBOIL AUTOMATIC FILTER DIFF.PRESS. HIGH
3468 10968 -RED.: LUBOIL INDICATOR FILTER DIFF.PRESS. HIGH
3469 10969 -OVRD RED.: LUBOIL INDICATOR FILTER DIFF.PRESS. HIGH
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 99 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3470 10970 -RED.: FUNCTION ERROR CYL. LUBRICATOR
3471 10971 -OVRD RED.: FUNCTION ERROR CYL. LUBRICATOR
3472 10972 -RED.: TURBINE DISC COOLING FUNCTION ERROR
3473 10973 -OVRD RED.: TURBINE DISC COOLING FUNCTION ERROR
3474 10974 -RED.: GEARBOX COMMON ALARM
3475 10975 -OVRD RED.: GEARBOX COMMON ALARM
3476 10976 -RED.: GEARBOX LUBOIL PRESSURE LOW
3477 10977 -OVRD RED.: GEARBOX LUBOIL PRESSURE LOW
3478 10978 -RED.: GEAR OIL TANK LEVEL LOW
3479 10979 -OVRD RED.: GEAR OIL TANK LEVEL LOW
3480 10980 -RED.: GEARBOX LUBOIL TEMP. HIGH
3481 10981 -OVRD RED.: GEARBOX LUBOIL TEMP. HIGH
3482 10982 -RED.: GEARBOX THRUST BEARING TEMP. HIGH
3483 10983 -OVRD RED.: GEARBOX THRUST BEARING TEMP. HIGH
3484 10984 -RED.: GEARBOX MAIN BEARING TEMP. HIGH
3485 10985 -OVRD RED.: GEARBOX MAIN BEARING TEMP. HIGH
3486 10986 -RED.: THERMAL OIL SYSTEM DISTURBANCE
3487 10987 -OVRD RED.: THERMAL OIL SYSTEM DISTURBANCE
3488 10988 -RED.: EXH. GAS BOILER DISTURBANCE
3489 10989 -OVRD RED.: EXH. GAS BOILER DISTURBANCE
3490 10990 -RED.: WINDMILLING PROTECT. AFT. SD/EMG.STOP OF OTHER ENG.
3491 10991 -OVRD RED.: WINDMILL. PROT. AFT. SD/EMG.STOP OF OTHER ENG.
3492 10992 -RED.: OILMIST DETECTOR
3493 10993 -OVRD RED.: OILMIST DETECTOR
3528 11028 -RED.: EXH. GAS TEMP. HIGH -CYL.: A 1
3529 11029 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: A 1
3530 11030 -RED.: EXH. GAS TEMP. HIGH -CYL.: A 2
3531 11031 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: A 2
3532 11032 -RED.: EXH. GAS TEMP. HIGH -CYL.: A 3
3533 11033 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: A 3
3534 11034 -RED.: EXH. GAS TEMP. HIGH -CYL.: A 4
3535 11035 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: A 4
3536 11036 -RED.: EXH. GAS TEMP. HIGH -CYL.: A 5
3537 11037 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: A 5
3538 11038 -RED.: EXH. GAS TEMP. HIGH -CYL.: A 6
3539 11039 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: A 6
3540 11040 -RED.: EXH. GAS TEMP. HIGH -CYL.: A 7
3541 11041 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: A 7
3542 11042 -RED.: EXH. GAS TEMP. HIGH -CYL.: A 8
3543 11043 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: A 8
3544 11044 -RED.: EXH. GAS TEMP. HIGH -CYL.: A 9
3545 11045 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: A 9
3546 11046 -RED.: EXH. GAS TEMP. HIGH -CYL.: A 10
3547 11047 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: A 10
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 100 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3548 11048 -RED.: EXH. GAS TEMP. HIGH BEF. TC A
3549 11049 -OVRD RED.: EXH. GAS TEMP. HIGH BEF. TC A
3552 11052 -RED.: EXH. GAS TEMP. HIGH -CYL.: B 1
3553 11053 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: B 1
3554 11054 -RED.: EXH. GAS TEMP. HIGH -CYL.: B 2
3555 11055 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: B 2
3556 11056 -RED.: EXH. GAS TEMP. HIGH -CYL.: B 3
3557 11057 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: B 3
3558 11058 -RED.: EXH. GAS TEMP. HIGH -CYL.: B 4
3559 11059 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: B 4
3560 11060 -RED.: EXH. GAS TEMP. HIGH -CYL.: B 5
3561 11061 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: B 5
3562 11062 -RED.: EXH. GAS TEMP. HIGH -CYL.: B 6
3563 11063 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: B 6
3564 11064 -RED.: EXH. GAS TEMP. HIGH -CYL.: B 7
3565 11065 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: B 7
3566 11066 -RED.: EXH. GAS TEMP. HIGH -CYL.: B 8
3567 11067 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: B 8
3568 11068 -RED.: EXH. GAS TEMP. HIGH -CYL.: B 9
3569 11069 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: B 9
3570 11070 -RED.: EXH. GAS TEMP. HIGH -CYL.: B 10
3571 11071 -OVRD RED.: EXH. GAS TEMP. HIGH -CYL.: B 10
3572 11072 -RED.: EXH. GAS TEMP. HIGH BEF. TC B
3573 11073 -OVRD RED.: EXH. GAS TEMP. HIGH BEF. TC B
3576 11076 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 1
3577 11077 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 1
3578 11078 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 2
3579 11079 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 2
3580 11080 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 3
3581 11081 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 3
3582 11082 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 4
3583 11083 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 4
3584 11084 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 5
3585 11085 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 5
3586 11086 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 6
3587 11087 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 6
3588 11088 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 7
3589 11089 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 7
3590 11090 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 8
3591 11091 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 8
3592 11092 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 9
3593 11093 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 9
3594 11094 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 10
3595 11095 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: A 10
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 101 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3596 11096 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 1
3597 11097 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 1
3598 11098 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 2
3599 11099 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 2
3600 11100 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 3
3601 11101 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 3
3602 11102 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 4
3603 11103 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 4
3604 11104 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 5
3605 11105 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 5
3606 11106 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 6
3607 11107 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 6
3608 11108 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 7
3609 11109 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 7
3610 11110 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 8
3611 11111 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 8
3612 11112 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 9
3613 11113 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 9
3614 11114 -RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 10
3615 11115 -OVRD RED.: EXH. GAS TEMP. MVD HIGH -CYL.: B 10
3656 11156 RED.: CR SAFETY VALVE OPEN
3657 11157 OVRD RED.: CR SAFETY VALVE OPEN
3658 11158 RED.: CR SAFETY VALVE ROW B OPEN
3659 11159 OVRD RED.: CR SAFETY VALVE ROW B OPEN
3660 11160 RED.: CR TOTAL LOSS OF RAIL PRESS. SENSORS
3661 11161 OVRD RED.: CR TOTAL LOSS OF RAIL PRESS. SENSORS
3704 11204 -DSENG: ENGINE UNDERSPEED SET:
3705 11205 -OVRD DSENG: ENGINE UNDERSPEED SET:
3706 11206 -DSENG: WINDMILLING SET:
3707 11207 -OVRD DSENG: WINDMILLING SET:
3708 11208 -DSENG: CLUTCH MEDIUM PRESS. LOW SET:
3709 11209 -OVRD DSENG: CL.MEDIUM PRESS.LOW SET:
3710 11210 -DSENG: GEARBOX LUBOIL PRESS. LOW SET:
3711 11211 -OVRD DSENG: G.BOX LUB. PRESS.LOW SET:
3712 11212 -DSENG: THRUST BEARING TEMP. HIGH SET:
3713 11213 -OVRD DSENG: THR. BEAR. TEMP. HIGH SET:
3720 11220 -DSENG: EMERGENCY DISENGAGE
3721 11221 -DSENG: EMERGENCY STOP ENGINE
3722 11222 -DSENG: AUTO SHUTDOWN ENGINE
3724 11224 -DSENG: CLUTCH MEDIUM PRESS. LOW
3725 11225 -OVRD DSENG: CLUTCH MEDIUM PRESS. LOW
3726 11226 -DSENG: SLIPPAGE MONITORING
3727 11227 -OVRD DSENG: SLIPPAGE MONITORING
3728 11228 -DSENG: GEARBOX LUBOIL PRESS. LOW
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 102 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3729 11229 -OVRD DSENG: GEARBOX LUBOIL PRESS. LOW
3730 11230 -DSENG: GEARBOX THRUST BEARING TEMP. HIGH
3731 11231 -OVRD DSENG: GEARBOX THRUST BEARING TEMP. HIGH
3768 11268 -SAF.SYST.: SF 2SE1000 SPEED SENSOR SAF.SYST. PROBABLE
3769 11269 -SAF.SYST.: SF 1SE1004 TC SPEED SENSOR SAF.SYST.
3770 11270 -SAF.SYST.: SF 1SE1004B TC B SPEED SENSOR SAF.SYST.
3771 11271 -SAF.SYST.: SF 2GT1022 FUEL ADMISSION SENSOR
3772 11272 -SAF.SYST.: SF 1TE1094-DE GENER. BEARING TEMP. SENSOR 1
3773 11273 -SAF.SYST.: SF 2TE1094-NDE GENER. BEARING TEMP. SENSOR 2
3774 11274 -SAF.SYST.: SF 1TE1095-L1 GENER. WINDING TEMP. SENSOR L1
3775 11275 -SAF.SYST.: SF 2TE1095-L2 GENER. WINDING TEMP. SENSOR L2
3776 11276 -SAF.SYST.: SF 3TE1095-L3 GENER. WINDING TEMP. SENSOR L3
3777 11277 -SAF.SYST.: SF 2PT2170 ENGINE LUBOIL PRESS. SENSOR
3778 11278 -SAF.SYST.: SF 2TE2170 ENGINE LUBOIL TEMP. SENSOR
3779 11279 -SAF.SYST.: SF 2PT2310 OILSUMP LEVEL SENSOR
3780 11280 -SAF.SYST.: SF 2PT2570 TC LUBOIL PRESS. SENSOR
3781 11281 -SAF.SYST.: SF 2TE2580 TC LUBOIL TEMP. SENSOR
3782 11282 -SAF.SYST.: SF 2TE2580B TC B LUBOIL TEMP. SENSOR
3783 11283 -SAF.SYST.: SF 2PT2970 GEARBOX LUBOIL PRESS. SENSOR
3784 11284 -SAF.SYST.: SF 2TE2970 GEARBOX LUBOIL TEMP. SENSOR
3785 11285 -SAF.SYST.: SF 2TE2971 PINION SHAFT TEMP. SENSOR
3786 11286 -SAF.SYST.: SF 2TE2972 OUTPUT SHAFT TEMP. SENSOR
3787 11287 -SAF.SYST.: SF 2PT2980 CLUTCH MEDIUM PRESS. SENSOR
3788 11288 -SAF.SYST.: SF 2TE2980 THRUST BEARING TEMP. SENSOR
3789 11289 -SAF.SYST.: SF 2PT3170 HT-CW PRESS. SENSOR
3790 11290 -SAF.SYST.: SF 2TE3180 HT-CW TEMP. SENSOR
3791 11291 -SAF.SYST.: SF 1PT7180 EMERGENCY STOP AIR PRESS. SENSOR
3792 11292 -SAF.SYST.: SF 1TE0004 SAF.SYST. CABINET TEMP. SENSOR 1
3817 11317 -SAF.SYST.: OVERRIDE ACTIVE FROM WHEELHOUSE
3818 11318 -SAF.SYST.: OVERRIDE ACTIVE FROM ECR PANEL
3819 11319 -SAF.SYST.: OVERRIDE ACTIVE FROM WING PORT
3820 11320 -SAF.SYST.: OVERRIDE ACTIVE FROM WING STBD
3821 11321 -SAF.SYST.: OVERRIDE ACTIVE CRANK CASE MONITORING
3823 11323 -SAF.SYST.: OVERRIDE ACTIVE
3824 11324 -SAF.SYST.: !ATTENTION! UPS OPERATION -SHUTDOWN in 20 min.
3832 11332 -SAF.SYST.: OILMIST DETECTOR DISTURBED
2998 11333 -SAF.SYST.: SF 1SZV1012 EMERGENCY STOP VALVE
2999 SAF.SYST.: DANGER!! EMERGENCY STOP SYSTEM OUT OF ORDER !!
3833 11334 -SAF.SYST.: ALARM ERROR IN BASE PARAMETER
3834 11335 -SAF.SYST.: FAILURE OVERSPEED PROTECTION
3835 11336 -SAF.SYST.: SHUTDOWN FAILURE
3836 11337 -SAF.SYST.: VOLTAGE FAILURE EMERGENCY STOP DEVICE
3837 11338 -SAF.SYST.: WIRE BREAK DETECTION BY MONITORING DEVICE
3838 11339 -SAF.SYST.: PLC-SYSTEM ERROR
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 103 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3839 11340 -SAF.SYST.: VOLTAGE FAILURE SAFETY SYSTEM
3840 11341 -SAF.SYST.: AMOUNT OF DETECTED I/O-MODULES INCORRECT
3841 11342 -SAF.SYST.: ENGINE CONTROL SYSTEM COMMUNICATION FAILURE
3842 11343 -SAF.SYST.: EC/AP - UNIT SYSTEM COMMUNICATION FAILURE
3843 11344 -SAF.SYST.: ALARM-PREPROC.-UNIT COMMUNICATION FAILURE
3844 11345 -SAF.SYST.: ENGINE MANAGEMENT SYSTEM COMMUNICATION FAILURE
3846 11347 -SAF.SYST.: EARTH FAULT DETECTED ON OPERATING PANELS
3847 11348 -SAF.SYST.: ECR-DISPLAY COMMUNICATION FAILURE
3848 11349 -SAF.SYST.: LOP-DISPLAY 1 COMMUNICATION FAILURE
3849 11350 -SAF.SYST.: LOP-DISPLAY 2 COMMUNICATION FAILURE
3850 11351 -SAF.SYST.: WH-DISPLAY COMMUNICATION FAILURE
3851 11352 -SAF.SYST.: ARCNet-BUS COMMUNICATION FAILURE
3852 11353 -SAF.SYST.: CAN-BUS COMMUNICATION FAILURE
3853 11354 -SAF.SYST.: ETHERNET COMMUNICATION - INIT FAILURE
3854 11355 -SAF.SYST.: PORT WING-DISPLAY COMMUNICATION FAILURE
3855 11356 -SAF.SYST.: STBD WING-DISPLAY COMMUNICATION FAILURE
3862 11363 -SAF.SYST.: FLASH WRITE / READ ERROR
3863 11364 -SAF.SYST.: POWER SUPPLY I OF SAFETY SYSTEM -FAILURE
3864 11365 -SAF.SYST.: POWER SUPPLY II OF SAFETY SYSTEM -FAILURE
3865 11366 -SAF.SYST.: POWER SUPPLY I OF ENGINE CONTROL -FAILURE
3866 11367 -SAF.SYST.: POWER SUPPLY II OF ENGINE CONTROL -FAILURE
3867 11368 -SAF.SYST.: POWER SUPPLY OF ETHERNET SWITCH -FAILURE
3868 11369 -SAF.SYST.: POWER SUPPLY OF EMERG. STOP SYSTEM -FAILURE
3869 11370 -SAF.SYST.: POWER SUPPLY OF EDS-D -FAILURE
3870 11371 -SAF.SYST.: POWER SUPPLY OF IPC ENGINE CONTROL -FAILURE
3871 11372 -SAF.SYST.: POWER SUPPLY OF CMS SAFETY SYSTEM -FAILURE
3872 11373 -SAF.SYST.: POWER SUPPLY OF OPERATOR PANEL -FAILURE
3895 11396 -SAF.SYST.: SF 1TE1064 MAIN BEARING SENSOR 01
3896 11397 -SAF.SYST.: SF 2TE1064 MAIN BEARING SENSOR 1
3897 11398 -SAF.SYST.: SF 3TE1064 MAIN BEARING SENSOR 2
3898 11399 -SAF.SYST.: SF 4TE1064 MAIN BEARING SENSOR 3
3899 11400 -SAF.SYST.: SF 5TE1064 MAIN BEARING SENSOR 4
3900 11401 -SAF.SYST.: SF 6TE1064 MAIN BEARING SENSOR 5
3901 11402 -SAF.SYST.: SF 7TE1064 MAIN BEARING SENSOR 6
3902 11403 -SAF.SYST.: SF 8TE1064 MAIN BEARING SENSOR 7
3903 11404 -SAF.SYST.: SF 9TE1064 MAIN BEARING SENSOR 8
3904 11405 -SAF.SYST.: SF 10TE1064 MAIN BEARING SENSOR 9
3905 11406 -SAF.SYST.: SF 11TE1064 MAIN BEARING SENSOR 10
3906 11407 -SAF.SYST.: SF 12TE1064 MAIN BEARING SENSOR 11
3907 11408 -SAF.SYST.: SF 1TE2880 SPLASH OIL SENSOR 1
3908 11409 -SAF.SYST.: SF 2TE2880 SPLASH OIL SENSOR 2
3909 11410 -SAF.SYST.: SF 3TE2880 SPLASH OIL SENSOR 3
3910 11411 -SAF.SYST.: SF 4TE2880 SPLASH OIL SENSOR 4
3911 11412 -SAF.SYST.: SF 5TE2880 SPLASH OIL SENSOR 5
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 104 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
3912 11413 -SAF.SYST.: SF 6TE2880 SPLASH OIL SENSOR 6
3913 11414 -SAF.SYST.: SF 7TE2880 SPLASH OIL SENSOR 7
3914 11415 -SAF.SYST.: SF 8TE2880 SPLASH OIL SENSOR 8
3915 11416 -SAF.SYST.: SF 9TE2880 SPLASH OIL SENSOR 9
3916 11417 -SAF.SYST.: SF 10TE2880 SPLASH OIL SENSOR 10
3917 11418 -SAF.SYST.: SF 1TE6570A EXHAUST GAS SENSOR 1
3918 11419 -SAF.SYST.: SF 2TE6570A EXHAUST GAS SENSOR 2
3919 11420 -SAF.SYST.: SF 3TE6570A EXHAUST GAS SENSOR 3
3920 11421 -SAF.SYST.: SF 4TE6570A EXHAUST GAS SENSOR 4
3921 11422 -SAF.SYST.: SF 5TE6570A EXHAUST GAS SENSOR 5
3922 11423 -SAF.SYST.: SF 6TE6570A EXHAUST GAS SENSOR 6
3923 11424 -SAF.SYST.: SF 7TE6570A EXHAUST GAS SENSOR 7
3924 11425 -SAF.SYST.: SF 8TE6570A EXHAUST GAS SENSOR 8
3925 11426 -SAF.SYST.: SF 9TE6570A EXHAUST GAS SENSOR 9
3926 11427 -SAF.SYST.: SF 10TE6570A EXHAUST GAS SENSOR 10
3927 11428 -SAF.SYST.: SF 1TE6575A EXHAUST GAS TC IN SENSOR 1
3928 11429 -SAF.SYST.: SF 1TE6580A EXHAUST GAS TC OUT SENSOR 1
3929 11430 -SAF.SYST.: SF 1TE6570B EXHAUST GAS SENSOR 1
3930 11431 -SAF.SYST.: SF 2TE6570B EXHAUST GAS SENSOR 2
3931 11432 -SAF.SYST.: SF 3TE6570B EXHAUST GAS SENSOR 3
3932 11433 -SAF.SYST.: SF 4TE6570B EXHAUST GAS SENSOR 4
3933 11434 -SAF.SYST.: SF 5TE6570B EXHAUST GAS SENSOR 5
3934 11435 -SAF.SYST.: SF 6TE6570B EXHAUST GAS SENSOR 6
3935 11436 -SAF.SYST.: SF 7TE6570B EXHAUST GAS SENSOR 7
3936 11437 -SAF.SYST.: SF 8TE6570B EXHAUST GAS SENSOR 8
3937 11438 -SAF.SYST.: SF 9TE6570B EXHAUST GAS SENSOR 9
3938 11439 -SAF.SYST.: SF 10TE6570B EXHAUST GAS SENSOR 10
3939 11440 -SAF.SYST.: SF 1TE6575B EXHAUST GAS TC IN SENSOR 1
3940 11441 -SAF.SYST.: SF 1TE6580B EXHAUST GAS TC OUT SENSOR 1
3941 11442 -SAF.SYST.: SF 1TE6500 EXHAUST GAS TEMP. COMP. SENSOR 1
3942 11443 -SAF.SYST.: SF 3TE6500 SAF.SYST. CABINET TEMP. SENSOR 1
3943 11444 -SAF.SYST.: CUT-OFF 1TE2880 SPLASH OIL SENSOR 1
3944 11445 -SAF.SYST.: CUT-OFF 2TE2880 SPLASH OIL SENSOR 2
3945 11446 -SAF.SYST.: CUT-OFF 3TE2880 SPLASH OIL SENSOR 3
3946 11447 -SAF.SYST.: CUT-OFF 4TE2880 SPLASH OIL SENSOR 4
3947 11448 -SAF.SYST.: CUT-OFF 5TE2880 SPLASH OIL SENSOR 5
3948 11449 -SAF.SYST.: CUT-OFF 6TE2880 SPLASH OIL SENSOR 6
3949 11450 -SAF.SYST.: CUT-OFF 7TE2880 SPLASH OIL SENSOR 7
3950 11451 -SAF.SYST.: CUT-OFF 8TE2880 SPLASH OIL SENSOR 8
3951 11452 -SAF.SYST.: CUT-OFF 9TE2880 SPLASH OIL SENSOR 9
3952 11453 -SAF.SYST.: CUT-OFF 10TE2880 SPLASH OIL SENSOR 10
4023 11524 -PreAl.: ENGINE SPEED HIGH SET:
4024 11525 -PreAl.: TC SPEED HIGH SET:
4025 11526 -PreAl.: TC SPEED B HIGH SET:
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 105 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4026 11527 -PreAl.: GENER.BEAR.TEMP. NDE HIGH SET:
4027 11528 -PreAl.: GENER.BEAR.TEMP. DE HIGH SET:
4028 11529 -PreAl.: GENER.WINDING TEMP. L1 HIGH SET:
4029 11530 -PreAl.: GENER.WINDING TEMP. L2 HIGH SET:
4030 11531 -PreAl.: GENER.WINDING TEMP. L3 HIGH SET:
4031 11532 -PreAl.: ENGINE LUBOIL PRESS. LOW:
4032 11533 -PreAl.: ENGINE LUBOIL TEMP. HIGH SET:
4033 11534 -PreAl.: LUBOIL LEVEL SERV. TANK HIGH SET:
4034 11535 -PreAl.: LUBOIL LEVEL SERV. TANK LOW SET:
4035 11536 -PreAl.: TC LUBOIL PRESS. LOW SET:
4036 11537 -PreAl.: TC LUBOIL TEMP. HIGH:
4037 11538 -PreAl.: TC B LUBOIL TEMP. HIGH:
4038 11539 -PreAl.: GEARBOX LUBOIL PRESS. LOW:
4039 11540 -PreAl.: GEARBOX LUBOIL TEMP. HIGH SET:
4040 11541 -PreAl.: THRUST BEARING TEMP. HIGH SET:
4041 11542 -PreAl.: GEAR PIN. SHAFT TEMP. HIGH SET:
4042 11543 -PreAl.: GEAR OUTP.SHAFT TEMP. HIGH SET:
4043 11544 -PreAl.: HT CW PRESS. LOW SET:
4044 11545 -PreAl.: HT CW TEMP. Before ENGINE LOW:
4045 11546 -PreAl.: HT CW TEMP. After ENGINE HIGH:
4046 11547 -PreAl.: NOZZLE CW PRESS. LOW:
4047 11548 -PreAl.: NOZZLE CW TEMP. HIGH:
4048 11549 -PreAl.: LT CW PRESS. LOW:
4049 11550 -PreAl.: LT CW TEMP. HIGH:
4050 11551 -PreAl.: FUEL OIL PRESS. LOW:
4051 11552 -PreAl.: FUEL OIL TEMP. HIGH:
4052 11553 -PreAl.: CHARGE AIR TEMP. HIGH:
4053 11554 -PreAl.: CHARGE AIR TEMP. B HIGH:
4054 11555 -PreAl.: START AIR PRESS. LOW:
4055 11556 -PreAl.: EMERG. STOP AIR PRESS. LOW:
4056 11557 -PreAl.: CONTROL AIR PRESS. LOW:
4071 11572 -PreAl.: OILMIST IN CRANKCASE
4072 11573 -PreAl.: LUBOIL AUTOMATIC FILTER 1PDAH 2105
4073 11574 -PreAl: LUBOIL AUTOMATIC FILTER RED. in 30 min. 2PDAH2105
4074 11575 -PreAl.: LUBOIL AUTOMATIC FILTER SD in 30 min. 2PDAH 2105
4075 11576 -PreAl.: LUBOIL INDICATOR FILTER 1PDAH 2106
4076 11577 -PreAl.: LUBOIL INDICATOR FILTER RED. in 30 min. 2PDAH2106
4077 11578 -PreAl.: LUBOIL INDICATOR FILTER SD in 30 min. 2PDAH 2106
4078 11579 -PreAl.: FAILURE CYL. LUBRIC. CAUSES AUTO LOAD RED.
4079 11580 -PreAl.: TURBINE DISC COOLING DISTURBANCE 1PA6182
4080 11581 -PreAl.: FUEL OIL LEAKAGE HIGH 1LSAH 5080
4081 11582 -PreAl.: FUEL OIL INDICATOR FILTER 1PDSH 5068
4082 11583 -PreAl.: GENERATOR COOLING WATER LEAKAGE DRIVE END
4083 11584 -PreAl.: GENERATOR COOLING WATER LEAKAGE NON-DRIVE END
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 106 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4119 11620 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 01
4120 11621 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 1
4121 11622 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 2
4122 11623 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 3
4123 11624 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 4
4124 11625 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 5
4125 11626 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 6
4126 11627 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 7
4127 11628 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 8
4128 11629 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 9
4129 11630 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 10
4130 11631 -PreAl.: MAIN BEARING TEMP. HIGH -BEARING: 11
4143 11644 -PreAl.: SPLASH OIL TEMP. MAX. -COMP.: 1
4144 11645 -PreAl.: SPLASH OIL TEMP. MAX. -COMP.: 2
4145 11646 -PreAl.: SPLASH OIL TEMP. MAX. -COMP.: 3
4146 11647 -PreAl.: SPLASH OIL TEMP. MAX. -COMP.: 4
4147 11648 -PreAl.: SPLASH OIL TEMP. MAX. -COMP.: 5
4148 11649 -PreAl.: SPLASH OIL TEMP. MAX. -COMP.: 6
4149 11650 -PreAl.: SPLASH OIL TEMP. MAX. -COMP.: 7
4150 11651 -PreAl.: SPLASH OIL TEMP. MAX. -COMP.: 8
4151 11652 -PreAl.: SPLASH OIL TEMP. MAX. -COMP.: 9
4152 11653 -PreAl.: SPLASH OIL TEMP. MAX. -COMP.: 10
4153 11654 -PreAl.: SPLASH OIL MVD TEMP. HIGH -COMP.: 1
4154 11655 -PreAl.: SPLASH OIL MVD TEMP. HIGH -COMP.: 2
4155 11656 -PreAl.: SPLASH OIL MVD TEMP. HIGH -COMP.: 3
4156 11657 -PreAl.: SPLASH OIL MVD TEMP. HIGH -COMP.: 4
4157 11658 -PreAl.: SPLASH OIL MVD TEMP. HIGH -COMP.: 5
4158 11659 -PreAl.: SPLASH OIL MVD TEMP. HIGH -COMP.: 6
4159 11660 -PreAl.: SPLASH OIL MVD TEMP. HIGH -COMP.: 7
4160 11661 -PreAl.: SPLASH OIL MVD TEMP. HIGH -COMP.: 8
4161 11662 -PreAl.: SPLASH OIL MVD TEMP. HIGH -COMP.: 9
4162 11663 -PreAl.: SPLASH OIL MVD TEMP. HIGH -COMP.: 10
4167 11668 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: A 1
4168 11669 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: A 2
4169 11670 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: A 3
4170 11671 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: A 4
4171 11672 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: A 5
4172 11673 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: A 6
4173 11674 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: A 7
4174 11675 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: A 8
4175 11676 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: A 9
4176 11677 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: A 10
4177 11678 -PreAl.: EXH. GAS TEMP. HIGH BEF. TC A
4179 11680 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: B 1
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 107 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4180 11681 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: B 2
4181 11682 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: B 3
4182 11683 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: B 4
4183 11684 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: B 5
4184 11685 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: B 6
4185 11686 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: B 7
4186 11687 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: B 8
4187 11688 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: B 9
4188 11689 -PreAl.: EXH. GAS TEMP. HIGH -CYL.: B 10
4189 11690 -PreAl.: EXH. GAS TEMP. HIGH BEF. TC B
4191 11692 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: A 1
4192 11693 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: A 2
4193 11694 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: A 3
4194 11695 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: A 4
4195 11696 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: A 5
4196 11697 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: A 6
4197 11698 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: A 7
4198 11699 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: A 8
4199 11700 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: A 9
4200 11701 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: A 10
4201 11702 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: B 1
4202 11703 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: B 2
4203 11704 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: B 3
4204 11705 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: B 4
4205 11706 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: B 5
4206 11707 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: B 6
4207 11708 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: B 7
4208 11709 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: B 8
4209 11710 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: B 9
4210 11711 -PreAl.: EXH. GAS TEMP. MVD HIGH -CYL.: B 10
4211 11712 -PreAl.: EXH. GAS TEMP. LOW -CYL.: A 1
4212 11713 -PreAl.: EXH. GAS TEMP. LOW -CYL.: A 2
4213 11714 -PreAl.: EXH. GAS TEMP. LOW -CYL.: A 3
4214 11715 -PreAl.: EXH. GAS TEMP. LOW -CYL.: A 4
4215 11716 -PreAl.: EXH. GAS TEMP. LOW -CYL.: A 5
4216 11717 -PreAl.: EXH. GAS TEMP. LOW -CYL.: A 6
4217 11718 -PreAl.: EXH. GAS TEMP. LOW -CYL.: A 7
4218 11719 -PreAl.: EXH. GAS TEMP. LOW -CYL.: A 8
4219 11720 -PreAl.: EXH. GAS TEMP. LOW -CYL.: A 9
4220 11721 -PreAl.: EXH. GAS TEMP. LOW -CYL.: A 10
4221 11722 -PreAl.: EXH. GAS TEMP. LOW -CYL.: B 1
4222 11723 -PreAl.: EXH. GAS TEMP. LOW -CYL.: B 2
4223 11724 -PreAl.: EXH. GAS TEMP. LOW -CYL.: B 3
4224 11725 -PreAl.: EXH. GAS TEMP. LOW -CYL.: B 4
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 108 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4225 11726 -PreAl.: EXH. GAS TEMP. LOW -CYL.: B 5
4226 11727 -PreAl.: EXH. GAS TEMP. LOW -CYL.: B 6
4227 11728 -PreAl.: EXH. GAS TEMP. LOW -CYL.: B 7
4228 11729 -PreAl.: EXH. GAS TEMP. LOW -CYL.: B 8
4229 11730 -PreAl.: EXH. GAS TEMP. LOW -CYL.: B 9
4230 11731 -PreAl.: EXH. GAS TEMP. LOW -CYL.: B 10
4231 11732 -PreAl.: KNOCKING VALUE HIGH -CYL.: A 1
4232 11733 -PreAl.: KNOCKING VALUE HIGH -CYL.: A 2
4233 11734 -PreAl.: KNOCKING VALUE HIGH -CYL.: A 3
4234 11735 -PreAl.: KNOCKING VALUE HIGH -CYL.: A 4
4235 11736 -PreAl.: KNOCKING VALUE HIGH -CYL.: A 5
4236 11737 -PreAl.: KNOCKING VALUE HIGH -CYL.: A 6
4237 11738 -PreAl.: KNOCKING VALUE HIGH -CYL.: A 7
4238 11739 -PreAl.: KNOCKING VALUE HIGH -CYL.: A 8
4239 11740 -PreAl.: KNOCKING VALUE HIGH -CYL.: A 9
4240 11741 -PreAl.: KNOCKING VALUE HIGH -CYL.: A 10
4241 11742 -PreAl.: KNOCKING VALUE HIGH -CYL.: B 1
4242 11743 -PreAl.: KNOCKING VALUE HIGH -CYL.: B 2
4243 11744 -PreAl.: KNOCKING VALUE HIGH -CYL.: B 3
4244 11745 -PreAl.: KNOCKING VALUE HIGH -CYL.: B 4
4245 11746 -PreAl.: KNOCKING VALUE HIGH -CYL.: B 5
4246 11747 -PreAl.: KNOCKING VALUE HIGH -CYL.: B 6
4247 11748 -PreAl.: KNOCKING VALUE HIGH -CYL.: B 7
4248 11749 -PreAl.: KNOCKING VALUE HIGH -CYL.: B 8
4249 11750 -PreAl.: KNOCKING VALUE HIGH -CYL.: B 9
4250 11751 -PreAl.: KNOCKING VALUE HIGH -CYL.: B 10
4263 11764 -PreAl.: RAIL PRESS. HIGH
4264 11765 -PreAl.: RAIL PRESS. LOW
4265 11766 -PreAl.: IGNITION OIL SUPPLY PRESS. HIGH
4295 11796 -PreAl.: GAS PRESS. Bef. GAS LINE LOW
4296 11797 -PreAl.: GAS PRESS. Bef. GAS LINE HIGH
4297 11798 -PreAl.: GAS PRESS. Bef. ENGINE LOW
4298 11799 -PreAl.: GAS PRESS. Bef. ENGINE HIGH
4299 11800 -PreAl.: GAS TEMP. Bef. GAS LINE LOW
4300 11801 -PreAl.: GAS TEMP. Bef. GAS LINE HIGH
4301 11802 -PreAl.: CONTROL AIR PRESS. GAS LINE LOW
4307 11808 -PreAl.: IGNITION GAS LEAKAGE PRESS. HIGH
4308 11809 -PreAl.: IGNITION GAS PRESS. BEF. ENGINE LOW
4309 11810 -PreAl.: IGNITION GAS PRESS. BEF. ENGINE HIGH
4310 11811 -PreAl.: ENGINE OVERLOAD
4327 11828 -QCO: RAIL PRESS. LOW
4328 11829 -QCO: RAIL PRESS. HIGH
4329 11830 -QCO: GAS PRESS. Bef. GAS LINE LOW
4330 11831 -QCO: GAS PRESS. Bef. GAS LINE HIGH
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 109 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4331 11832 -QCO: GAS PRESS. Bef. ENGINE LINE LOW
4332 11833 -QCO: GAS PRESS. Bef. ENGINE LINE HIGH
4333 11834 -QCO: ENGINE SPEED LOW
4343 11844 -QCO: ANTI KNOCK CONTROL NOT READY
4344 11845 -QCO: ANTI KNOCK CONTROL SENSOR FAULT
4345 11846 -QCO: ANTI KNOCK CONTROL HEAVY KNOCKING
4346 11847 -QCO: CR INPULSE MAJOR ALARM
4347 11848 -QCO: CR PILOT OIL INJECTION CRITICAL
4348 11849 -QCO: CR CYLINDER FAILURE
4349 11850 -QCO: CR INPULSE CAN ERROR
4350 11851 -QCO: MANUAL QUICK CHANGE OVER -ECR-
4351 11852 -QCO: MANUAL QUICK CHANGE OVER -spare-
4352 11853 -QCO: SOGAV INPULSE MAJOR ALARM
4353 11854 -QCO: SOGAV ERROR
4354 11855 -QCO: SOGAV CYLINDER FAILURE
4355 11856 -QCO: SOGAV INPULSE CAN ERROR
4356 11857 -QCO: SOGAV INPULSE PICK UP FAILURE
4357 11858 -QCO: QCO-spare
4358 11859 -QCO: INPULSES CAN2 COMMON ERROR
4359 11860 -QCO: PreAl. MAIN BEARING TEMP. MONITORING
4360 11861 -QCO: PreAl. SPLASH OIL TEMP. MONITORING
4361 11862 -QCO: INPULSE EXTERNAL MASTER FAILURE
4362 11863 -QCO: QCO-spare
4363 11864 -QCO: LAMBDA CONTROL DISTURBED
4364 11865 -QCO: GAS LINE SAFETY SHUTOFF VALVE CLOSED
4365 11866 -QCO: ENGINE LOAD LOW
4366 11867 -QCO: ENGINE LOAD HIGH
4367 11868 -QCO: TOTAL LOSS LOAD SIGNAL
4368 11869 -QCO: TOTAL LOSS OF RAIL PRESS. SENSORS
4369 11870 -QCO: TOTAL LOSS OF GAS PRESS. Bef. GAS LINE SENSORS
4370 11871 -QCO: TOTAL LOSS OF GAS PRESS. Bef. ENGINE SENSORS
4371 11872 -QCO: TOTAL LOSS OF EXH. GAS TEMP. SENSORS
4375 11876 -QCO: EXH. GAS TEMP. HIGH -CYL.: A 1
4376 11877 -QCO: EXH. GAS TEMP. HIGH -CYL.: A 2
4377 11878 -QCO: EXH. GAS TEMP. HIGH -CYL.: A 3
4378 11879 -QCO: EXH. GAS TEMP. HIGH -CYL.: A 4
4379 11880 -QCO: EXH. GAS TEMP. HIGH -CYL.: A 5
4380 11881 -QCO: EXH. GAS TEMP. HIGH -CYL.: A 6
4381 11882 -QCO: EXH. GAS TEMP. HIGH -CYL.: A 7
4382 11883 -QCO: EXH. GAS TEMP. HIGH -CYL.: A 8
4383 11884 -QCO: EXH. GAS TEMP. HIGH -CYL.: A 9
4384 11885 -QCO: EXH. GAS TEMP. HIGH -CYL.: A 10
4385 11886 -QCO: EXH. GAS TEMP. HIGH Bef. TC A
4387 11888 -QCO: EXH. GAS TEMP. HIGH -CYL.: B 1
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 110 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4388 11889 -QCO: EXH. GAS TEMP. HIGH -CYL.: B 2
4389 11890 -QCO: EXH. GAS TEMP. HIGH -CYL.: B 3
4390 11891 -QCO: EXH. GAS TEMP. HIGH -CYL.: B 4
4391 11892 -QCO: EXH. GAS TEMP. HIGH -CYL.: B 5
4392 11893 -QCO: EXH. GAS TEMP. HIGH -CYL.: B 6
4393 11894 -QCO: EXH. GAS TEMP. HIGH -CYL.: B 7
4394 11895 -QCO: EXH. GAS TEMP. HIGH -CYL.: B 8
4395 11896 -QCO: EXH. GAS TEMP. HIGH -CYL.: B 9
4396 11897 -QCO: EXH. GAS TEMP. HIGH -CYL.: B 10
4397 11898 -QCO: EXH. GAS TEMP. HIGH Bef. TC B
4399 11900 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: A 1
4400 11901 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: A 2
4401 11902 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: A 3
4402 11903 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: A 4
4403 11904 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: A 5
4404 11905 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: A 6
4405 11906 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: A 7
4406 11907 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: A 8
4407 11908 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: A 9
4408 11909 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: A 10
4409 11910 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: B 1
4410 11911 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: B 2
4411 11912 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: B 3
4412 11913 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: B 4
4413 11914 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: B 5
4414 11915 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: B 6
4415 11916 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: B 7
4416 11917 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: B 8
4417 11918 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: B 9
4418 11919 -QCO: EXH. GAS TEMP. MVD HIGH -CYL.: B 10
4419 11920 -QCO: EXH. GAS TEMP. LOW -CYL.: A 1
4420 11921 -QCO: EXH. GAS TEMP. LOW -CYL.: A 2
4421 11922 -QCO: EXH. GAS TEMP. LOW -CYL.: A 3
4422 11923 -QCO: EXH. GAS TEMP. LOW -CYL.: A 4
4423 11924 -QCO: EXH. GAS TEMP. LOW -CYL.: A 5
4424 11925 -QCO: EXH. GAS TEMP. LOW -CYL.: A 6
4425 11926 -QCO: EXH. GAS TEMP. LOW -CYL.: A 7
4426 11927 -QCO: EXH. GAS TEMP. LOW -CYL.: A 8
4427 11928 -QCO: EXH. GAS TEMP. LOW -CYL.: A 9
4428 11929 -QCO: EXH. GAS TEMP. LOW -CYL.: A 10
4429 11930 -QCO: EXH. GAS TEMP. LOW -CYL.: B 1
4430 11931 -QCO: EXH. GAS TEMP. LOW -CYL.: B 2
4431 11932 -QCO: EXH. GAS TEMP. LOW -CYL.: B 3
4432 11933 -QCO: EXH. GAS TEMP. LOW -CYL.: B 4
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 111 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4433 11934 -QCO: EXH. GAS TEMP. LOW -CYL.: B 5
4434 11935 -QCO: EXH. GAS TEMP. LOW -CYL.: B 6
4435 11936 -QCO: EXH. GAS TEMP. LOW -CYL.: B 7
4436 11937 -QCO: EXH. GAS TEMP. LOW -CYL.: B 8
4437 11938 -QCO: EXH. GAS TEMP. LOW -CYL.: B 9
4438 11939 -QCO: EXH. GAS TEMP. LOW -CYL.: B 10
4439 11940 -QCO: KNOCKING VALUE HIGH -CYL.: A 1
4440 11941 -QCO: KNOCKING VALUE HIGH -CYL.: A 2
4441 11942 -QCO: KNOCKING VALUE HIGH -CYL.: A 3
4442 11943 -QCO: KNOCKING VALUE HIGH -CYL.: A 4
4443 11944 -QCO: KNOCKING VALUE HIGH -CYL.: A 5
4444 11945 -QCO: KNOCKING VALUE HIGH -CYL.: A 6
4445 11946 -QCO: KNOCKING VALUE HIGH -CYL.: A 7
4446 11947 -QCO: KNOCKING VALUE HIGH -CYL.: A 8
4447 11948 -QCO: KNOCKING VALUE HIGH -CYL.: A 9
4448 11949 -QCO: KNOCKING VALUE HIGH -CYL.: A 10
4449 11950 -QCO: KNOCKING VALUE HIGH -CYL.: B 1
4450 11951 -QCO: KNOCKING VALUE HIGH -CYL.: B 2
4451 11952 -QCO: KNOCKING VALUE HIGH -CYL.: B 3
4452 11953 -QCO: KNOCKING VALUE HIGH -CYL.: B 4
4453 11954 -QCO: KNOCKING VALUE HIGH -CYL.: B 5
4454 11955 -QCO: KNOCKING VALUE HIGH -CYL.: B 6
4455 11956 -QCO: KNOCKING VALUE HIGH -CYL.: B 7
4456 11957 -QCO: KNOCKING VALUE HIGH -CYL.: B 8
4457 11958 -QCO: KNOCKING VALUE HIGH -CYL.: B 9
4458 11959 -QCO: KNOCKING VALUE HIGH -CYL.: B 10
4471 11972 -ACO: RAIL SUPPLY PRESS. LOW
4472 11973 -ACO: GAS TEMP. LOW
4473 11974 -ACO: GAS TEMP. HIGH
4474 11975 -ACO: CHARGE AIR TEMP. HIGH
4475 11976 -ACO: CONTROL AIR PRESS. GAS LINE LOW
4480 11981 -ACO: TOTAL LOSS OF GAS TEMP. SENSORS xTE5862
4481 11982 -ACO: TOTAL LOSS OF CHARGE AIR TEMP. SENSORS xTE6180
4482 11983 -ACO: TOTAL LOSS OF CONTROL AIR PRESS. SENSORS xTE7460
4487 11988 -ALARM: SF 1TE1094-DE GENER. BEARING TEMP. SENSOR 1
4488 11989 -ALARM: SF 2TE1094-NDE GENER. BEARING TEMP. SENSOR 2
4489 11990 -ALARM: SF 1TE1095-L1 GENER. WINDING TEMP. SENSOR L1
4490 11991 -ALARM: SF 2TE1095-L2 GENER. WINDING TEMP. SENSOR L2
4491 11992 -ALARM: SF 3TE1095-L3 GENER. WINDING TEMP. SENSOR L3
4492 11993 -ALARM: SF 1PT2170 ENGINE LUBOIL PRESS. SENSOR
4493 11994 -ALARM: SF 1TE2170 ENGINE LUBOIL TEMP. SENSOR
4494 11995 -ALARM: SF 1TE2180 ENGINE LUBOIL TEMP. Aft. ENGINE
4495 11996 -ALARM: SF 1PT2310 OILSUMP LEVEL SENSOR
4496 11997 -ALARM: SF 1PT2570 TC LUBOIL PRESS. SENSOR
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 112 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4497 11998 -ALARM: SF 1TE2580 TC LUBOIL TEMP. SENSOR
4498 11999 -ALARM: SF 1TE2580B TC B LUBOIL TEMP. SENSOR
4499 12000 -ALARM: SF 1PT2970 GEARBOX LUBOIL PRESS. SENSOR
4500 12001 -ALARM: SF 1TE2970 GEARBOX LUBOIL TEMP. SENSOR
4501 12002 -ALARM: SF 1TE2971 PINION SHAFT TEMP. SENSOR
4502 12003 -ALARM: SF 1TE2972 OUTPUT SHAFT TEMP. SENSOR
4503 12004 -ALARM: SF 1PT2980 CLUTCH MEDIUM PRESS. SENSOR
4504 12005 -ALARM: SF 1TE2980 THRUST BEARING TEMP. SENSOR
4505 12006 -ALARM: SF 1TE3168 HT-CW TEMP. Bef. CHARGE AIR COOLER
4506 12007 -ALARM: SF 1PT3170 HT-CW PRESS. SENSOR
4507 12008 -ALARM: SF 1TE3170 HT-CW TEMP. SENSOR
4508 12009 -ALARM: SF 1TE3180 HT-CW TEMP. SENSOR
4509 12010 -ALARM: SF 1PT3470 NOZZLE CW PRESS. SENSOR
4510 12011 -ALARM: SF 1TE3470 NOZZLE CW TEMP. SENSOR
4511 12012 -ALARM: SF 1PT4170 LT CW PRESS. SENSOR
4512 12013 -ALARM: SF 1TE4170 LT CW TEMP. SENSOR
4513 12014 -ALARM: SF 1TE4180 LT CW TEMP. Aft. CHARGE AIR COOLER
4514 12015 -ALARM: SF 1PT 5070 FUEL OIL PRESS. SENSOR
4515 12016 -ALARM: SF 1TE5070 FUEL OIL TEMP. SENSOR
4516 12017 -ALARM: SF 1TE6000 AMBIENT AIR TEMP. SENSOR
4517 12018 -ALARM: SF 1PT6100 INTAKE AIR PRESS. SENSOR
4518 12019 -ALARM: SF 1TE6100 INTAKE AIR TEMP. SENSOR
4519 12020 -ALARM: SF 1TE6170 CHARGE AIR TEMP. Aft. COMPRESS. TC
4520 12021 -ALARM: SF 1TE 6170B CHARGE AIR TEMP. Aft. COMPRESS. TC B
4521 12022 -ALARM: SF 2PT6180 CHARGE AIR PRESS. SENSOR
4522 12023 -ALARM: SF 2PT6180B CHARGE AIR PRESS. SENSOR B
4523 12024 -ALARM: SF 1TE6180 CHARGE AIR TEMP. SENSOR
4524 12025 -ALARM: SF 1TE6180B CHARGE AIR TEMP. SENSOR B
4525 12026 -ALARM: SF 1PT6182 TC DISC COOL. AIR PRESS. SENSOR
4526 12027 -ALARM: SF 1PT7180 EMERGENCY STOP AIR PRESS. SENSOR
4527 12028 -ALARM: SF 1PT7400 CONTROL AIR PRESS. SENSOR
4528 12029 -ALARM: SF GENERATOR POWER SIGNAL
4535 12036 -ALARM: SF 1TE1064 MAIN BEARING SENSOR 01
4536 12037 -ALARM: SF 2TE1064 MAIN BEARING SENSOR 1
4537 12038 -ALARM: SF 3TE1064 MAIN BEARING SENSOR 2
4538 12039 -ALARM: SF 4TE1064 MAIN BEARING SENSOR 3
4539 12040 -ALARM: SF 5TE1064 MAIN BEARING SENSOR 4
4540 12041 -ALARM: SF 6TE1064 MAIN BEARING SENSOR 5
4541 12042 -ALARM: SF 7TE1064 MAIN BEARING SENSOR 6
4542 12043 -ALARM: SF 8TE1064 MAIN BEARING SENSOR 7
4543 12044 -ALARM: SF 9TE1064 MAIN BEARING SENSOR 8
4544 12045 -ALARM: SF 10TE1064 MAIN BEARING SENSOR 9
4545 12046 -ALARM: SF 11TE1064 MAIN BEARING SENSOR 10
4546 12047 -ALARM: SF 12TE1064 MAIN BEARING SENSOR 11
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 113 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4547 12048 -ALARM: SF 1TE2880 SPLASH OIL SENSOR 1
4548 12049 -ALARM: SF 2TE2880 SPLASH OIL SENSOR 2
4549 12050 -ALARM: SF 3TE2880 SPLASH OIL SENSOR 3
4550 12051 -ALARM: SF 4TE2880 SPLASH OIL SENSOR 4
4551 12052 -ALARM: SF 5TE2880 SPLASH OIL SENSOR 5
4552 12053 -ALARM: SF 6TE2880 SPLASH OIL SENSOR 6
4553 12054 -ALARM: SF 7TE2880 SPLASH OIL SENSOR 7
4554 12055 -ALARM: SF 8TE2880 SPLASH OIL SENSOR 8
4555 12056 -ALARM: SF 9TE2880 SPLASH OIL SENSOR 9
4556 12057 -ALARM: SF 10TE2880 SPLASH OIL SENSOR 10
4557 12058 -ALARM: SF 1TE6570A EXHAUST GAS SENSOR 1
4558 12059 -ALARM: SF 2TE6570A EXHAUST GAS SENSOR 2
4559 12060 -ALARM: SF 3TE6570A EXHAUST GAS SENSOR 3
4560 12061 -ALARM: SF 4TE6570A EXHAUST GAS SENSOR 4
4561 12062 -ALARM: SF 5TE6570A EXHAUST GAS SENSOR 5
4562 12063 -ALARM: SF 6TE6570A EXHAUST GAS SENSOR 6
4563 12064 -ALARM: SF 7TE6570A EXHAUST GAS SENSOR 7
4564 12065 -ALARM: SF 8TE6570A EXHAUST GAS SENSOR 8
4565 12066 -ALARM: SF 9TE6570A EXHAUST GAS SENSOR 9
4566 12067 -ALARM: SF 10TE6570A EXHAUST GAS SENSOR 10
4567 12068 -ALARM: SF 1TE6575A EXHAUST GAS TC IN SENSOR 1
4568 12069 -ALARM: SF 1TE6580A EXHAUST GAS TC OUT SENSOR 1
4569 12070 -ALARM: SF 1TE6570B EXHAUST GAS SENSOR 1
4570 12071 -ALARM: SF 2TE6570B EXHAUST GAS SENSOR 2
4571 12072 -ALARM: SF 3TE6570B EXHAUST GAS SENSOR 3
4572 12073 -ALARM: SF 4TE6570B EXHAUST GAS SENSOR 4
4573 12074 -ALARM: SF 5TE6570B EXHAUST GAS SENSOR 5
4574 12075 -ALARM: SF 6TE6570B EXHAUST GAS SENSOR 6
4575 12076 -ALARM: SF 7TE6570B EXHAUST GAS SENSOR 7
4576 12077 -ALARM: SF 8TE6570B EXHAUST GAS SENSOR 8
4577 12078 -ALARM: SF 9TE6570B EXHAUST GAS SENSOR 9
4578 12079 -ALARM: SF 10TE6570B EXHAUST GAS SENSOR 10
4579 12080 -ALARM: SF 1TE6575B EXHAUST GAS TC IN SENSOR 1
4580 12081 -ALARM: SF 1TE6580B EXHAUST GAS TC OUT SENSOR 1
4581 12082 -ALARM: SF 1TE0003 EC-SYST. CABINET TEMP. SENSOR 1
4582 12083 -ALARM: SF 4TE6500 SAF.SYST. CABINET TEMP. SENSOR 1
4583 12084 -ALARM: ARCnet COMMUNICATION FAILURE
4584 12085 -ALARM: CAN COMMUNICATION FAILURE
4585 12086 -ALARM: ETHERNET COMMUNICATION - INIT FAILURE
4586 12087 -ALARM: SAFETY SYSTEM COMMUNICATION FAILURE
4587 12088 -ALARM: ENGINE CONTROL SYSTEM COMMUNICATION FAILURE
4588 12089 -ALARM: ENGINE MANAGEMENT SYSTEM COMMUNICATION FAILURE
4589 12090 -ALARM: PLC-SYSTEM ERROR
4590 12091 -ALARM: ALARM ERROR IN BASE PARAMETER
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 114 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4591 12092 -ALARM: AMOUNT OF DETECTED I/O-MODULES INCORRECT
4594 12095 -ALARM: TC DISC MONITORING DISTURBED
4595 12096 -ALARM: ENG.CONTROL-AUX. COMMUNICATION FAILURE
4599 12100 -ALARM: FAILURE F1: 24 VDC EC/AP POWER SUPPLY
4600 12101 -ALARM: FAILURE F2: 24 VDC INDICAT. LAMPS POWER SUPPLY
4601 12102 -ALARM: FAILURE F3: 24 VDC POWER STACK POWER SUPPLY
4602 12103 -ALARM: FAILURE F4: 24 VDC EC/AP PLC-SYST.POWER SUPPLY
4603 12104 -ALARM: FAILURE F5: 24 VDC EC/AP BIN. OUTP. POWER SUPPLY
4604 12105 -ALARM: FAILURE F6: 24 VDC EC/AP BIN. OUTP. POWER SUPPLY
4605 12106 -ALARM: FAILURE F7: 24 VDC EC/AP BIN. OUTP. POWER SUPPLY
4606 12107 -ALARM: FAILURE F8: 24 VDC EC/AP ANAL. OUTP. POWER SUPPLY
4607 12108 -ALARM: FAILURE F9: 24 VDC AKC POWER SUPPLY
4608 12109 -ALARM: FAILURE F10: 24 VDC ENG.DATA.ACQUIS. POWER SUPPLY
4609 12110 -ALARM: FAILURE F11: 24 VDC LAMBDA CONTROL POWER SUPPLY
4610 12111 -ALARM: FAILURE F12: 24 VDC CHATCO POWER SUPPLY
4615 12116 -ALARM: SENSOR DEV. 1SE1000:
4617 12118 -ALARM: SENSOR DEV. 1PT2170:
4618 12119 -ALARM: SENSOR DEV. 1TE2170:
4619 12120 -ALARM: SENSOR DEV. 1PT2570:
4620 12121 -ALARM: SENSOR DEV. 1TE2580:
4621 12122 -ALARM: SENS.DEV. 1TE2580B:
4622 12123 -ALARM: SENSOR DEV. 1PT2970:
4623 12124 -ALARM: SENSOR DEV. 1TE2970:
4624 12125 -ALARM: SENSOR DEV. 1TE2971:
4625 12126 -ALARM: SENSOR DEV. 1TE2972:
4626 12127 -ALARM: SENSOR DEV. 1TE2980:
4627 12128 -ALARM: SENSOR DEV. 1PT3170:
4628 12129 -ALARM: SENSOR DEV. 1TE3180:
4629 12130 -ALARM: SENSOR DEV. 1PT2310:
4663 12164 -ALARM: EARTH FAULT DETECTED ON ALARM PREPROC.
4791 12292 -EC-SYST.: SF 1SE1000 ENGINE SPEED SENSOR
4792 12293 -EC-SYST.: SF 1GT1022 PID UNLIMITED SIGNAL
4793 12294 -EC-SYST.: SF 1PT2170 ENGINE LUBOIL PRESS. SENSOR
4794 12295 -EC-SYST.: SF 1PT2310 LUBOIL LEVEL SERVICE TANK
4795 12296 -EC-SYST.: SF 2PT2310 LUBOIL LEVEL SERVICE TANK
4796 12297 -EC-SYST.: SF 1PT2470 CYL. LUBRICATION PRESS. SENSOR
4797 12298 -EC-SYST.: SF 1TE3165 HT CW TEMP. Aft. CONTROL VALVE
4798 12299 -EC-SYST.: SF 3TE3180 HT CW TEMP. SENSOR for CONTROLLER
4799 12300 -EC-SYST.: SF 1TE6000 AMBIENT AIR TEMP. SENSOR
4800 12301 -EC-SYST.: SF 1TE6100 INTAKE AIR TEMP. SENSOR
4801 12302 -EC-SYST.: SF 1PT6180 CHARGE AIR PRESS. SENSOR
4802 12303 -EC-SYST.: SF 2TE6180 CHARGE AIR TEMP. SENSOR
4803 12304 -EC-SYST.: SF 1PT7170 START AIR PRESS. SENSOR
4804 12305 -EC-SYST.: SF ASYMMETRIC LOAD SHARING INPUT SIGNAL
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 115 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4805 12306 -EC-SYST.: SF GOVERNOR SPEED SENSOR
4806 12307 -EC-SYST.: SF GOVERNOR SPEED REFERENCE EXTERNAL SIGNAL
4807 12308 -EC-SYST.: SF GOVERNOR SPEED REFERENCE EXTERNAL LOCAL
4808 12309 -EC-SYST.: SF GOVERNOR LOAD REFERENCE EXTERNAL SIGNAL
4809 12310 -EC-SYST.: SF GOVERNOR LSS SIGNAL
4810 12311 -EC-SYST.: SF GOVERNOR SPEED ENGINE 2
4811 12312 -EC-SYST.: SF GOVERNOR ACTUATOR
4812 12313 -EC-SYST.: SF GOVERNOR ANALOG SPARE 1
4813 12314 -EC-SYST.: SF GOVERNOR ANALOG SPARE 2
4814 12315 -EC-SYST.: SF FWE SENSOR
4815 12316 -EC-SYST.: SF 1PT6182 TC DISC COOL. AIR PRESS. SENSOR
4816 12317 -EC-SYST.: SF CHATCO VALVE POSITION FEEDBACK OF 1TCV6180
4817 12318 -EC-SYST.: SF HT VALVE POSITION FEEDBACK OF 1TCV3180
4818 12319 -EC-SYST.: SF 1TE000x POWER SUPPLY CABINET TEMP. SENSOR
4819 12320 -EC-SYST.: SF POSITION FEEDBACK HT-CW CONTROL VALVE
4820 12321 -EC-SYST.: SF POSITION FEEDBACK LT-CW CONTROL VALVE
4821 12322 -EC-SYST.: SF POS. FEEDB. LUBE OIL TEMP. CONTROL VALVE
4822 12323 -EC-SYST.: SF POS. FEEDB. INTAKE AIR PREHEAT. CTRL VALVE
4823 12324 -EC-SYST.: ENGINE START FAILURE
4824 12325 -EC-SYST.: ENGINE STOP FAILURE
4827 12328 -EC-SYST.: ERROR STARTING SEQUENCE
4831 12332 -EC-SYST.: ERROR CLUTCH SEQUENCE
4833 12334 -EC-SYST.: CR OPERATION FAILURE
4834 12335 -EC-SYST.: DF OPERATION FAILURE
4835 12336 -EC-SYST.: DIESEL OPERATION FAILURE
4839 12340 -EC-SYST.: CYLINDER LUBRICATION NO FLOW
4840 12341 -EC-SYST.: CYLINDER LUBRICATION SUPPLY PRESS. LOW
4842 12343 -EC-SYST.: CHATCO ERROR - CLOSING 1TCV6180
4843 12344 -EC-SYST.: FEEDB.ERR.OPENING HT/LT-CONNECT. FLAP (CHATCO)
4844 12345 -EC-SYST.: FEEDB.ERR.CLOSING HT/LT-CONNECT. FLAP (CHATCO)
4845 12346 -EC-SYST.: FEEDBACK ERROR CHARGE AIR TEMP. CONTROL FLAP
4846 12347 -EC-SYST.: ERROR CHARGE AIR TEMP. CONTROLLER
4848 12349 -EC-SYST.: VIT ERROR DURING POSITIONING
4849 12350 -EC-SYST.: VIT ERROR OPENING ERROR OF BRAKE
4850 12351 -EC-SYST.: VIT ERROR CLOSING ERROR OF BRAKE
4851 12352 -EC-SYST.: VIT ERROR LUBOIL PRESS. LOW
4852 12353 -EC-SYST.: VIT ERROR LIMIT SWITCH / POSITION UNKNOWN
4853 12354 -EC-SYST.: VIT FAILURE - ROW A
4854 12355 -EC-SYST.: VIT FAILURE - ROW B
4855 12356 -EC-SYST.: FUNCT. ERR. WASTE GATE FAILURE (TC SPEED DECAY)
4857 12358 -EC-SYST.: ERROR SLOW TURN PROCEDURE TOO FAST
4858 12359 -EC-SYST.: ERROR EXPECTED SLOW TURNS NOT REACHED
4859 12360 -EC-SYST.: ERROR MANUAL TURN OF ENGINE NOT YET DONE
4860 12361 -EC-SYST.: FUNCTION ERROR ERROR AT ENGINE STOP
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 116 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4861 12362 -EC-SYST.: FUNCTION ERROR PRELUBRICATION PUMP
4862 12363 -EC-SYST.: CYL.LUBRIC. PRESS. HIGH -MANUAL TURN REQUIRED-
4863 12364 -EC-SYST.: FUNCTION ERROR CYL. LUBRICATION
4864 12365 -EC-SYST.: FUNCTION ERROR CYL.LUBRIC.-LOAD RED. in 30 min.
4865 12366 -EC-SYST.: FUNCTION ERROR SERVICE TANK REFILL CONTROL
4866 12367 -EC-SYST.: FAILURE CHARGE AIR BLOW OFF
4867 12368 -EC-SYST.: FUNCTION ERROR VALVE SEAT LUBRICATOR
4868 12369 -EC-SYST.: ERROR LUBOIL PRESS. VALVE SEAT LUBRICATION
4869 12370 -EC-SYST.: FAILURE WATER INJECTION MODULE
4871 12372 -EC-SYST.: GOVERNOR MINOR ALARM
4872 12373 -EC-SYST.: GOVERNOR MAJOR ALARM
4873 12374 -EC-SYST.: GOVERNOR OVERLOAD
4874 12375 -EC-SYST.: SWITCH OVER TO ECR SPEED SETTING
4879 12380 -EC-SYST.: EM-DRIVER NOT READY
4880 12381 -EC-SYST.: CHATCO ERROR - CLOSING CONTROL VALVE
4881 12382 -EC-SYST.: CHATCO ERROR - DISCONNECTING LT-CIRCUIT
4882 12383 -EC-SYST.: CHATCO ERROR - CONNECTING LT-CIRCUIT
4883 12384 -EC-SYST.: CHATCO ERROR - DISCONNECTING HT-CIRCUIT
4884 12385 -EC-SYST.: CHATCO ERROR - CONNECTING HT-CIRCUIT
4885 12386 -EC-SYST.: CHARGE AIR BLOW OFF - CHARGE AIR PRESS. HIGH
4886 12387 -EC-SYST.: CHARGE AIR BLOW OFF -EXH. GAS TEMP. AFT. TC LOW
4887 12388 -EC-SYST.: TURBINE DISC COOLING DISTURBANCE 1PA6182
4888 12389 -EC-SYST.: TC DISC MONITORING DISTURBED
4903 12404 -EC-SYST.: VTA POSITION DEVIATION A/B
4904 12405 -EC-SYST.: VTA TC SPEED DEVIATION A/B
4905 12406 -EC-SYST.: VTA CHARGE AIR PRESS. DEVIATION A/B
4906 12407 -EC-SYST.: VTA ERROR FREQUENCY CONVERTER A
4907 12408 -EC-SYST.: VTA ERROR FREQUENCY CONVERTER B
4919 12420 -EC-SYST.: FAILURE MOTOR PROTECTION CYLINDER LUBRICATION
4920 12421 -EC-SYST.: FAILURE MOTOR PROTECTION CYLINDER LUBRICATION B
4921 12422 -EC-SYST.: FAILURE MOTOR PROTECTION VALVE SEAT LUBRICAT.
4922 12423 -EC-SYST.: FAILURE MOTOR PROTECTION VALVE SEAT LUBRICAT. B
4923 12424 -EC-SYST.: FAILURE MOTOR PROTECTION VIT
4924 12425 -EC-SYST.: FAILURE CIRCUIT-BREAKER VIT ROW A
4925 12426 -EC-SYST.: FAILURE CIRCUIT-BREAKER VIT ROW B
4927 12428 -EC-SYST.: POWER FAILURE
4928 12429 -EC-SYST.: FAILURE 24 VDC POWER - SUPPLY POWER STACK
4929 12430 -EC-SYST.: FAILURE SUPPLY VOLTAGE EM-DRIVER
4930 12431 -EC-SYST.: GOVERNOR VOLTAGE FAILURE
4931 12432 -EC-SYST.: POWER SUPPLY I OF SPEED CONTROL -FAILURE
4932 12433 -EC-SYST.: POWER SUPPLY II OF SPEED CONTROL -FAILURE
4933 12434 -EC-SYST.: POWER SUPPLY I OF ENGINE CONTROL -FAILURE
4934 12435 -EC-SYST.: POWER SUPPLY II OF ENGINE CONTROL -FAILURE
4935 12436 -EC-SYST.: STANDBY ALARM ENGINE LUBOIL PRESS.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 117 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
4936 12437 -EC-SYST.: STANDBY ALARM HT-CW PRESS.
4937 12438 -EC-SYST.: STANDBY ALARM LT-CW PRESS.
4939 12440 -EC-SYST.: HT-CW TEMP. LOW, SWITCH OFF HEAT CONSUMERS
4940 12441 -EC-SYST.: HT-CW PREHEATING ERROR
4941 12442 -EC-SYST.: NOZZLE-CW PREHEATING ERROR
4942 12443 -EC-SYST.: NOZZLE-CW LOW FLOW
4947 12448 -EC-SYST.: GENERATOR JACKING PUMP FAILURE
4948 12449 -EC-SYST.: GENERATOR JACKING PUMP ON AT RUNNING ENGINE
4949 12450 -EC-SYST.: GRID SYNCHRONISATION FAILURE
4951 12452 -EC-SYST.: FAILURE TC 2170 LUBOIL TEMP. CONTROLLER
4952 12453 -EC-SYST.: FAILURE TC 6180 CHATCO CONTROLLER
4953 12454 -EC-SYST.: FAILURE CHARGE AIR TEMP. CONTROLLER
4954 12455 -EC-SYST.: FAILURE TC 4170 LT TEMP. CONTROLLER
4955 12456 -EC-SYST.: FAILURE TC 3180 HT TEMP. CONTROLLER
4956 12457 -EC-SYST.: FAILURE TC 6100 INTAKE AIR TEMP. CONTROLLER
4957 12458 -EC-SYST.: FAILURE LAMBDA CONTROLLER
4958 12459 -EC-SYST.: FAILURE VTA CONTROLLER
4959 12460 -EC-SYST.: FAILURE KNOCK CONTROLLER
4960 12461 -EC-SYST.: FAILURE POWER CONTROLLER
4967 12468 -EC-SYST.: ECR-DISPLAY COMMUNICATION FAILURE
4968 12469 -EC-SYST.: LOP-DISPLAY 1 COMMUNICATION FAILURE
4969 12470 -EC-SYST.: LOP-DISPLAY 2 COMMUNICATION FAILURE
4970 12471 -EC-SYST.: WH-DISPLAY COMMUNICATION FAILURE
4971 12472 -EC-SYST.: ARCNet-BUS COMMUNICATION FAILURE
4972 12473 -EC-SYST.: CAN-BUS COMMUNICATION FAILURE
4973 12474 -EC-SYST.: ETHERNET COMMUNICATION - INIT FAILURE
4974 12475 -EC-SYST.: SAFETY SYSTEM COMMUNICATION FAILURE
4975 12476 -EC-SYST.: ALARM-PREPROC.-UNIT COMMUNICATION FAILURE
4976 12477 -EC-SYST.: ENGINE MANAGEMENT SYSTEM COMMUNICATION FAILURE
4977 12478 -EC-SYST.: PLC-SYSTEM ERROR
4978 12479 -EC-SYST.: ALARM ERROR IN BASE PARAMETER
4979 12480 -EC-SYST.: AMOUNT OF DETECTED I/O-MODULES INCORRECT
4980 12481 -EC-SYST.: PORT WING-DISPLAY COMMUNICATION FAILURE
4981 12482 -EC-SYST.: STBD WING-DISPLAY COMMUNICATION FAILURE
4982 12483 -EC-SYST.: FLASH WRITE / READ ERROR
5031 12532 -EC-SYST.: EARTH FAULT DETECTED ON PUMPS STARTER
5032 12533 -EC-SYST.: EARTH FAULT DETECTED FROM EXTERNAL
5033 12534 -EC-SYST.: EARTH FAULT DETECTED ON SOLENOID VALVES
5035 12536 -EC-SYST.: EARTH FAULT DETECTED ON GOVERNOR CONTROL
5047 12548 -CR-: SF 1PT5275 IGNITION OIL SUPPLY PRESSURE
5048 12549 -CR-: PILOT OIL LEAKAGE HIGH
5049 12550 -CR-: FAILURE MOTOR PROTECTION CR PUMP
5050 12551 -CR-: FAILURE CAN 2.0A COMMUNICATION CR-INPULSE
5052 12553 -CR-: FAILURE CR RAIL PRESSURE CONTROL VALVE DRIVER
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 118 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5054 12555 -CR-: CR-INPULSE - SYNCHRONISATION FAULT
5055 12556 -CR-: CR-INPULSE - FAILURE PICK UP 1
5056 12557 -CR-: CR-INPULSE - FAILURE PICK UP 2
5057 12558 -CR-: CR-INPULSE - FAILURE ACTUATOR 1
5058 12559 -CR-: CR-INPULSE - FAILURE ACTUATOR 2
5059 12560 -CR-: CR-INPULSE - SIGNAL FAILURE LIMITER SHIFT
5060 12561 -CR-: CR-INPULSE - SIGNAL FAILURE EXTERNAL LOAD LIMITER
5061 12562 -CR-: CR-INPULSE - SIGNAL FAILURE RAIL PRESSURE 1
5062 12563 -CR-: CR-INPULSE - SIGNAL FAILURE RAIL PRESSURE 2
5063 12564 -CR-: CR-INPULSE - CAN 1 ERROR
5064 12565 -CR-: CR-INPULSE - CAN 2 ERROR
5065 12566 -CR-: CR-INPULSE - FAILURE INJECTOR POWER
5066 12567 -CR-: CR-INPULSE - FAILURE AUXILIARY POWER
5067 12568 -CR-: CR-INPULSE - MCU TEMP. CRITICAL
5068 12569 -CR-: CR-INPULSE - MCU TEMP. HIGH
5069 12570 -CR-: CR-INPULSE - MCU SYSTEM ALARM
5070 12571 -CR-: CR-INPULSE - MCU STATUS ALARM
5071 12572 -CR-: CR-INPULSE - RAIL PRESS. SETPOINT NOT REACHED
5072 12573 -CR-: CR-INPULSE - RAIL PRESS. DYNAMIC DEVIATION
5073 12574 -CR-: CR-INPULSE - RAIL PRESS. SENSOR 1 STATIC DRIFT
5074 12575 -CR-: CR-INPULSE - RAIL PRESS. SENSOR 2 STATIC DRIFT
5075 12576 -CR-: CR-INPULSE - IGNITION OIL DIFFERENTIAL FILTER ALARM
5079 12580 -CR-: CR-INPULSE - FAILURE MUX 1
5080 12581 -CR-: CR-INPULSE - FAILURE MUX 2
5081 12582 -CR-: CR-INPULSE - FAILURE MUX 3
5082 12583 -CR-: CR-INPULSE - FAILURE MUX 4
5083 12584 -CR-: CR-INPULSE - FAILURE MUX 5
5084 12585 -CR-: CR-INPULSE - FAILURE MUX 6
5087 12588 -CR-: CR AUTO-OFF: PILOT OIL SUPPLY PRESS. LOW
5088 12589 -CR-: CR AUTO-OFF: CR-INPULSE MAJOR ALARM
5089 12590 -CR-: CR AUTO-OFF: REQUEST BY CR-INPULSE
5095 12596 -CR-: CR COMMON VALVE ERROR CYL. A1
5096 12597 -CR-: CR COMMON VALVE ERROR CYL. A2
5097 12598 -CR-: CR COMMON VALVE ERROR CYL. A3
5098 12599 -CR-: CR COMMON VALVE ERROR CYL. A4
5099 12600 -CR-: CR COMMON VALVE ERROR CYL. A5
5100 12601 -CR-: CR COMMON VALVE ERROR CYL. A6
5101 12602 -CR-: CR COMMON VALVE ERROR CYL. A7
5102 12603 -CR-: CR COMMON VALVE ERROR CYL. A8
5103 12604 -CR-: CR COMMON VALVE ERROR CYL. A9
5104 12605 -CR-: CR COMMON VALVE ERROR CYL. A10
5105 12606 -CR-: CR COMMON VALVE ERROR CYL. B1
5107 12608 -CR-: CR COMMON VALVE ERROR CYL. B3
5108 12609 -CR-: CR COMMON VALVE ERROR CYL. B4
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 119 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5109 12610 -CR-: CR COMMON VALVE ERROR CYL. B5
5110 12611 -CR-: CR COMMON VALVE ERROR CYL. B6
5111 12612 -CR-: CR COMMON VALVE ERROR CYL. B7
5112 12613 -CR-: CR COMMON VALVE ERROR CYL. B8
5113 12614 -CR-: CR COMMON VALVE ERROR CYL. B9
5114 12615 -CR-: CR COMMON VALVE ERROR CYL. B10
5127 12628 -CR- PLC: EMERGENCY-STOP ACTIVATED
5133 12634 -CR-: RAIL PRESS. PUMP SEIZURE EXPECTED BANK - A -
5134 12635 -CR-: RAIL PRESS. PUMP SEIZURE EXPECTED BANK - B -
5135 12636 -CR- PLC: AC POWERSUPPLY CIRCUIT BREAKER FAILED
5136 12637 -CR- ECU: EMERGENCY OPERATION
5137 12638 -CR- PLC: 24V VOLTAGE SUPPLY FAILURE
5138 12639 -CR- PLC: UPS BATTERY LOAD-LEVEL LOW
5139 12640 -CR- PLC: AC POWERSUPPLY FAILED, UPS OPERATION
5140 12641 -CR- PLC: UPS BATTERY-ECU1 LOAD-LEVEL LOW
5141 12642 -CR- PLC: UPS BATTERY-ECU2 LOAD-LEVEL LOW
5142 12643 -CR- PLC: PLC-SYSTEM FAILURE
5143 12644 -CR- PLC: SPARE E62_07
5144 12645 -CR- PLC: ECU1-OVERCURRENT
5145 12646 -CR- PLC: ECU2-OVERCURRENT
5146 12647 -CR- PLC: FUEL LEAKAGE IN HOTBOX
5147 12648 -CR- PLC: CAN-SETUP FAILURE
5148 12649 -CR- PLC: CAN-COMMUNICATION ERROR
5149 12650 -CR- ECU 1: SUPPLY VOLTAGE FAILURE
5150 12651 -CR- ECU 2: SUPPLY VOLTAGE FAILURE
5151 12652 -CR- ECU: ENGINE OVERLOAD
5152 12653 -CR- PLC: EXH. GAS TEMP. ACQUISITION COMM. FAILED
5153 12654 -CR- PLC: ECU CAN COMMUNICATION FAILED
5155 12656 -CR- PLC: SPARE
5156 12657 -CR- PLC: HIGH PRESS. LEAKAGE LEVEL HIGH
5157 12658 -CR- PLC: AMOUNT OF I/O MODULES TOO LESS
5158 12659 -CR- PLC: EARTH FAULT DETECTED
5159 12660 -CR- EXH. GAS GOVERNOR CYL. A LIMIT REACHED
5160 12661 -CR- EXH. GAS GOVERNOR CYL. B LIMIT REACHED
5167 12668 -CR- PLC: ERROR 548 - E 62.01
5168 12669 -CR- PLC: ERROR 549 - E 62.02
5169 12670 -CR- PLC: ERROR 550 - E 62.03
5170 12671 -CR- ECU 1: MAJOR ALARM
5171 12672 -CR- ECU 2: MAJOR ALARM
5173 12674 -CR- PLC: ERROR 554 - E 62.07
5174 12675 -CR- ECU 1: MINOR ALARM
5175 12676 -CR- ECU 2: MINOR ALARM
5177 12678 -CR- ECU: EMERGENCY OPERATION ACTIVE
5179 12680 -CR- PLC: COMMUNICATION ERROR TO OTHER PLC
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 120 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5180 12681 -CR- PLC: CAN COMMUNICATION ERROR TO ECU
5189 12690 -CR- PLC: EL. START AIR DISTRIBUTOR FAILURE
5190 12691 -CR- PLC: TEMP. SENSOR A1 FAILED
5191 12692 -CR- PLC: TEMP. SENSOR A2 FAILED
5192 12693 -CR- PLC: TEMP. SENSOR A3 FAILED
5193 12694 -CR- PLC: TEMP. SENSOR A4 FAILED
5194 12695 -CR- PLC: TEMP. SENSOR A5 FAILED
5195 12696 -CR- PLC: TEMP. SENSOR A6 FAILED
5196 12697 -CR- PLC: TEMP. SENSOR A7 FAILED
5197 12698 -CR- PLC: TEMP. SENSOR A8 FAILED
5198 12699 -CR- PLC: TEMP. SENSOR A9 FAILED
5199 12700 -CR- PLC: TEMP. SENSOR A10 FAILED
5200 12701 -CR- PLC: TEMP. SENSOR B1 FAILED
5201 12702 -CR- PLC: TEMP. SENSOR B2 FAILED
5202 12703 -CR- PLC: TEMP. SENSOR B3 FAILED
5203 12704 -CR- PLC: TEMP. SENSOR B4 FAILED
5204 12705 -CR- PLC: TEMP. SENSOR B5 FAILED
5205 12706 -CR- PLC: TEMP. SENSOR B6 FAILED
5206 12707 -CR- PLC: TEMP. SENSOR B7 FAILED
5207 12708 -CR- PLC: TEMP. SENSOR B8 FAILED
5208 12709 -CR- PLC: TEMP. SENSOR B9 FAILED
5209 12710 -CR- PLC: TEMP. SENSOR B10 FAILED
5213 12714 -CR- ECU 2: PICKUP 1 FAILURE
5214 12715 -CR- ECU 2: PICKUP 2 FAILURE
5215 12716 -CR- PLC: WB FUEL INDEX ECU 1
5217 12718 -CR- PLC: WB FUEL INDEX ECU 2
5222 12723 -CR-: FUNCTION ERROR FLUSHING VALVE
5223 12724 -CR- FUEL TEMP. NOT REACHED. DO NOT START
5224 12725 -CR- PLC: SAFETY VALVE OPEN
5225 12726 -CR- PLC: WB SPEED SIGNAL ECU 1
5227 12728 -CR- PLC: WB SPEED SIGNAL ECU 2
5228 12729 -CR- PLC: WB SPEED SETPOINT ANALOG
5229 12730 -CR-FUEL TEMP. ROW B NOT REACHED. DO NOT START
5230 12731 -CR- PLC: SAFETY VALVE ROW B OPEN
5235 12736 -CR- PLC: WB 1TE5070 FUEL TEMP. ENG. INLET
5236 12737 -CR- PLC: WB 1TE5080 FUEL TEMP.AFT.FLUSH VALVE
5237 12738 -CR- PLC: WB 1TE5081 FUEL TEMP.AFT.SAFETY VALVE
5238 12739 -CR- PLC: WB 1TE5080B FUEL TEMP.AFT.FLUSH VALVE
5239 12740 -CR- PLC: WB 1TE5081B FUEL TEMP.AFT.SAFETY VALVE
5245 12746 -CR- PLC: WB ENGINE SPEED
5247 12748 -CR- PLC: WB CHARGE AIR PRESS.
5257 12758 -CR- PLC: FUEL OIL LEAKAGE HIGH
5263 12764 -CR- Err3094: INTERNAL ERROR
5264 12765 -CR- Err3093: STACK ERROR
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 121 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5265 12766 -CR- Err3092: PAIRING ERROR
5266 12767 -CR- Err3091: LOGICAL ERROR
5267 12768 -CR- Err3090: DATA ERROR
5270 12771 -CR- Err3087: 90-VOLT SUPPLY 1 ERROR
5271 12772 -CR- Err3086: 90-VOLT SUPPLY TEMP. ERROR
5272 12773 -CR- Err3085: VOLTAGE ERROR
5273 12774 -CR- Err3084: ANALOG OUTPUT 2 FEED. ERROR
5274 12775 -CR- Err3083: ANALOG OUTPUT 1 FEED. ERROR
5275 12776 -CR- Err3082: AD-CONVERTER ERROR
5276 12777 -CR- Err3081: 12-VOLT INT. ERROR
5278 12779 -CR- Err3079: TEMP. INT. ERROR
5279 12780 -CR- Err3078: RAM TEST ERROR
5280 12781 -CR- Err3077: PROGRAM-TEST ERROR
5281 12782 -CR- Err3076: PARAMETER STORE ERROR
5282 12783 -CR- Err3075: CLEAR FLASH ERROR
5284 12785 -CR- Err3073: CAN-COMMUNICATION 2 ERROR
5285 12786 -CR- Err3072: CAN-BUS 2 ERROR
5286 12787 -CR- Err3071: CAN-COMMUNICATION 1 ERROR
5287 12788 -CR- Err3070: CAN-BUS 1 ERROR
5288 12789 -CR- Err3069: CYLINDER-B10 ERROR
5289 12790 -CR- Err3068: CYLINDER-B9 ERROR
5290 12791 -CR- Err3067: CYLINDER-B8 ERROR
5291 12792 -CR- Err3066: CYLINDER-B7 ERROR
5292 12793 -CR- Err3065: CYLINDER-B6 ERROR
5293 12794 -CR- Err3064: CYLINDER-B5 ERROR
5294 12795 -CR- Err3063: CYLINDER-B4 ERROR
5295 12796 -CR- Err3062: CYLINDER-B3 ERROR
5296 12797 -CR- Err3061: CYLINDER-B2 ERROR
5297 12798 -CR- Err3060: CYLINDER-B1 ERROR
5298 12799 -CR- Err3059: CYLINDER-A10 ERROR
5299 12800 -CR- Err3058: CYLINDER-A9 ERROR
5300 12801 -CR- Err3057: CYLINDER-A8 ERROR
5301 12802 -CR- Err3056: CYLINDER-A7 ERROR
5302 12803 -CR- Err3055: CYLINDER-A6 ERROR
5303 12804 -CR- Err3054: CYLINDER-A5 ERROR
5304 12805 -CR- Err3053: CYLINDER-A4 ERROR
5305 12806 -CR- Err3052: CYLINDER-A3 ERROR
5306 12807 -CR- Err3051: CYLINDER-A2 ERROR
5307 12808 -CR- Err3050: CYLINDER-A1 ERROR
5315 12816 -CR- Err3042: RAIL PRESS. PUMP 4 ERROR
5316 12817 -CR- Err3041: RAIL PRESS. PUMP 3 ERROR
5317 12818 -CR- Err3040: PUMP CURRENT OUTPUT 2 ERROR
5318 12819 -CR- Err3039: PUMP CURRENT OUTPUT 1 ERROR
5319 12820 -CR- Err3038: RAIL B PRESS. SETP. NOT REACHED
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 122 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5320 12821 -CR- Err3037: RAIL PRESS. SETP. NOT REACHED
5321 12822 -CR- Err3036: INJECTION OVERLAPPING ERROR
5323 12824 -CR- Err3034: TRIP MASTER ERROR
5324 12825 -CR- Err3033: TRIP SLAVE ERROR
5325 12826 -CR- Err3032: REDUNDANT ECU ERROR
5326 12827 -CR- Err3031: CONNECTION LOST ERROR
5339 12840 -CR- Err3010: RAIL PRESS. SENSOR B1 ERROR
5340 12841 -CR- Err3009: RAIL PRESS. SENSOR A1 ERROR
5342 12843 -CR- Err3007: SETPOINT ANALOG DIRECT ERROR
5343 12844 -CR- Err3006: FUEL-LIMITER EXTERN DIRECT ERROR
5345 12846 -CR- Err3004: OVERSPEED ERROR
5346 12847 -CR- Err3003: PICK-UP INDEX ERROR
5347 12848 -CR- Err3002: PICK-UP 2 ERROR
5348 12849 -CR- Err3001: PICK-UP 1 ERROR
5350 12851 -CR- Err13063: CR-SENSOR B2 DRIFT ERROR
5351 12852 -CR- Err13062: CR-SENSOR A2 DRIFT ERROR
5352 12853 -CR- Err13061: CR-SENSOR B1 DRIFT ERROR
5353 12854 -CR- Err13060: CR-SENSOR A1 DRIFT ERROR
5364 12865 -CR- Err13049: FUNCTION FLUSHING RAIL 2 ERROR
5365 12866 -CR- Err13048: FUNCTION FLUSHING RAIL 1 ERROR
5366 12867 -CR- Err13047: FUNCT. SETP. ANAL. or DIG. ERROR
5368 12869 -CR- Err13045: FUNCTION DYNAMIC 2 or 1 ERROR
5369 12870 -CR- Err13044: FUNCTION ERROR-RESET ERROR
5370 12871 -CR- Err13043: FUNCTION SPEED-DECR. ERROR
5371 12872 -CR- Err13042: FUNCTION SPEED-INCR. ERROR
5373 12874 -CR- Err13040: FUNCTION ENGINE-STOP ERROR
5378 12879 -CR- Err13035: CR-PRESSURE SENS. 2 DIFF. ERROR
5379 12880 -CR- Err13034: CR-PRESSURE SENS. 1 DIFF. ERROR
5381 12882 -CR- Err13032: SETPOINT ANALOG DIFF. ERROR
5382 12883 -CR- Err13031: FUEL-LIMITER DIFFERENCE ERROR
5395 12896 -CR- Err13010: RAIL PRESS. B2
5396 12897 -CR- Err13009: RAIL PRESS. A2
5398 12899 -CR- Err13007: SETPOINT ANALOG CAN ERROR
5399 12900 -CR- Err13006: FUEL-LIMITER EXTERN CAN ERROR
5403 12904 -CR- Err13002: SYNCHRONISATION PICK-UP 2 ERROR
5404 12905 -CR- Err13001: SYNCHRONISATION PICK-UP 1 ERROR
5415 12916 -GAS-: AKC NOT READY
5417 12918 -GAS-: FAILURE CAN 2.0A COMMUNICATION SOGAV-INPULSE
5418 12919 -GAS-: SF 1Pyxxxx GAS FLOW METER
5419 12920 -GAS-: SF 1PT5862 GAS PRESS. Bef. GAS CONTROL VALVE
5420 12921 -GAS-: SF 1TE5862 GAS TEMP. Bef. GAS CONTROL VALVE
5421 12922 -GAS-: SF 1PT5865 MAIN GAS PRESS.
5422 12923 -GAS-: SF 1PT7460 CONTROL AIR PRESS. f. GAS CONTROL UNIT
5423 12924 -GAS-: GAS LINE DIFFERENTIAL FILTER PRESS. HIGH
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 123 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5424 12925 -GAS-: SOGAV-INPULSE - ENGINE OVERSPEED DETECTED
5425 12926 -GAS-: SOGAV-INPULSE - GAS OVERLOAD
5426 12927 -GAS-: SOGAV-INPULSE - SYNCHRONISATION FAULT
5427 12928 -GAS-: SOGAV-INPULSE - FAILURE PICK UP 1
5428 12929 -GAS-: SOGAV-INPULSE - FAILURE PICK UP 2
5429 12930 -GAS-: SOGAV-INPULSE - FAILURE ACTUATOR 1
5430 12931 -GAS-: SOGAV-INPULSE - FAILURE ACTUATOR 2
5431 12932 -GAS-: SOGAV-INPULSE - FAILURE GAS SPLITT VALUE SIGNAL
5432 12933 -GAS-: SOGAV-INPULSE - FAILURE GENERATOR LOAD SIGNAL
5433 12934 -GAS-: SOGAV-INPULSE - FAILURE SPEED REFERENCE SIGNAL
5434 12935 -GAS-: SOGAV-INPULSE - FAILURE CHARGE AIR PRESS. SIGNAL
5435 12936 -GAS-: SOGAV-INPULSE - CAN 1 ERROR
5436 12937 -GAS-: SOGAV-INPULSE - CAN 2 ERROR
5437 12938 -GAS-: SOGAV-INPULSE - FAILURE INJECTOR POWER
5438 12939 -GAS-: SOGAV-INPULSE - FAILURE AUXILIARY POWER
5439 12940 -GAS-: SOGAV-INPULSE - MCU TEMP. CRITICAL
5440 12941 -GAS-: SOGAV-INPULSE - MCU TEMP. HIGH
5441 12942 -GAS-: SOGAV-INPULSE - MCU SYSTEM ALARM
5442 12943 -GAS-: SOGAV-INPULSE - MCU STATUS ALARM
5447 12948 -GAS-: SOGAV-INPULSE - FAILURE MUX 1
5448 12949 -GAS-: SOGAV-INPULSE - FAILURE MUX 2
5449 12950 -GAS-: SOGAV-INPULSE - FAILURE MUX 3
5450 12951 -GAS-: SOGAV-INPULSE - FAILURE MUX 4
5451 12952 -GAS-: SOGAV-INPULSE - FAILURE MUX 5
5452 12953 -GAS-: SOGAV-INPULSE - FAILURE MUX 6
5463 12964 -GAS-: SF 1XE1220A KNOCKING SENSOR A1
5464 12965 -GAS-: SF 2XE1220A KNOCKING SENSOR A2
5465 12966 -GAS-: SF 3XE1220A KNOCKING SENSOR A3
5466 12967 -GAS-: SF 4XE1220A KNOCKING SENSOR A4
5467 12968 -GAS-: SF 5XE1220A KNOCKING SENSOR A5
5468 12969 -GAS-: SF 6XE1220A KNOCKING SENSOR A6
5469 12970 -GAS-: SF 7XE1220A KNOCKING SENSOR A7
5470 12971 -GAS-: SF 8XE1220A KNOCKING SENSOR A8
5471 12972 -GAS-: SF 9XE1220A KNOCKING SENSOR A9
5472 12973 -GAS-: SF 10XE1220A KNOCKING SENSOR A10
5473 12974 -GAS-: SF 1XE1220B KNOCKING SENSOR B1
5474 12975 -GAS-: SF 2XE1220B KNOCKING SENSOR B2
5475 12976 -GAS-: SF 3XE1220B KNOCKING SENSOR B3
5476 12977 -GAS-: SF 4XE1220B KNOCKING SENSOR B4
5477 12978 -GAS-: SF 5XE1220B KNOCKING SENSOR B5
5478 12979 -GAS-: SF 6XE1220B KNOCKING SENSOR B6
5479 12980 -GAS-: SF 7XE1220B KNOCKING SENSOR B7
5480 12981 -GAS-: SF 8XE1220B KNOCKING SENSOR B8
5481 12982 -GAS-: SF 9XE1220B KNOCKING SENSOR B9
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 124 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5482 12983 -GAS-: SF 10XE1220B KNOCKING SENSOR B10
5483 12984 -GAS-: KNOCK CONTROL SPEED SENSOR FAILURE
5495 12996 -GAS-: SOGAV COMMON VALVE ERROR CYL. A1
5496 12997 -GAS-: SOGAV COMMON VALVE ERROR CYL. A2
5497 12998 -GAS-: SOGAV COMMON VALVE ERROR CYL. A3
5498 12999 -GAS-: SOGAV COMMON VALVE ERROR CYL. A4
5499 13000 -GAS-: SOGAV COMMON VALVE ERROR CYL. A5
5500 13001 -GAS-: SOGAV COMMON VALVE ERROR CYL. A6
5501 13002 -GAS-: SOGAV COMMON VALVE ERROR CYL. A7
5502 13003 -GAS-: SOGAV COMMON VALVE ERROR CYL. A8
5503 13004 -GAS-: SOGAV COMMON VALVE ERROR CYL. A9
5504 13005 -GAS-: SOGAV COMMON VALVE ERROR CYL. A10
5505 13006 -GAS-: SOGAV COMMON VALVE ERROR CYL. B1
5506 13007 -GAS-: SOGAV COMMON VALVE ERROR CYL. B2
5507 13008 -GAS-: SOGAV COMMON VALVE ERROR CYL. B3
5508 13009 -GAS-: SOGAV COMMON VALVE ERROR CYL. B4
5509 13010 -GAS-: SOGAV COMMON VALVE ERROR CYL. B5
5510 13011 -GAS-: SOGAV COMMON VALVE ERROR CYL. B6
5511 13012 -GAS-: SOGAV COMMON VALVE ERROR CYL. B7
5512 13013 -GAS-: SOGAV COMMON VALVE ERROR CYL. B8
5513 13014 -GAS-: SOGAV COMMON VALVE ERROR CYL. B9
5514 13015 -GAS-: SOGAV COMMON VALVE ERROR CYL. B10
5519 13020 -GAS-: IGNITION COMMON ERROR CYL. A1
5520 13021 -GAS-: IGNITION COMMON ERROR CYL. A2
5521 13022 -GAS-: IGNITION COMMON ERROR CYL. A3
5522 13023 -GAS-: IGNITION COMMON ERROR CYL. A4
5523 13024 -GAS-: IGNITION COMMON ERROR CYL. A5
5524 13025 -GAS-: IGNITION COMMON ERROR CYL. A6
5525 13026 -GAS-: IGNITION COMMON ERROR CYL. A7
5526 13027 -GAS-: IGNITION COMMON ERROR CYL. A8
5527 13028 -GAS-: IGNITION COMMON ERROR CYL. A9
5528 13029 -GAS-: IGNITION COMMON ERROR CYL. A10
5529 13030 -GAS-: IGNITION COMMON ERROR CYL. B1
5530 13031 -GAS-: IGNITION COMMON ERROR CYL. B2
5531 13032 -GAS-: IGNITION COMMON ERROR CYL. B3
5532 13033 -GAS-: IGNITION COMMON ERROR CYL. B4
5533 13034 -GAS-: IGNITION COMMON ERROR CYL. B5
5534 13035 -GAS-: IGNITION COMMON ERROR CYL. B6
5535 13036 -GAS-: IGNITION COMMON ERROR CYL. B7
5536 13037 -GAS-: IGNITION COMMON ERROR CYL. B8
5537 13038 -GAS-: IGNITION COMMON ERROR CYL. B9
5538 13039 -GAS-: IGNITION COMMON ERROR CYL. B10
5543 13044 -GAS-: SOGAV - FAILURE MUX 1A ( A1, A6, A7 )
5544 13045 -GAS-: SOGAV - FAILURE MUX 2A ( A3, A9, A4 )
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 125 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5545 13046 -GAS-: SOGAV - FAILURE MUX 3A (A5, A8, A2 )
5546 13047 -GAS-: SOGAV - FAILURE MUX 1B ( B1, B6, B7 )
5547 13048 -GAS-: SOGAV - FAILURE MUX 2B ( B3, B9, B4 )
5548 13049 -GAS-: SOGAV - FAILURE MUX 3B ( B5, B8, B2 )
5549 13050 -GAS-: INJECTION - FAILURE MUX 1A ( A1, A6, A7 )
5550 13051 -GAS-: INJECTION - FAILURE MUX 2A ( A3, A9, A4 )
5551 13052 -GAS-: INJECTION - FAILURE MUX 3A (A5, A8, A2 )
5552 13053 -GAS-: INJECTION - FAILURE MUX 1B ( B1, B6, B7 )
5553 13054 -GAS-: INJECTION - FAILURE MUX 2B ( B3, B9, B4 )
5554 13055 -GAS-: INJECTION - FAILURE MUX 3B ( B5, B8, B2 )
5575 13076 -GAS-: SF 1PT5868 GAS PRESS. Bef. ENGINE
5576 13077 -GAS-: SF 1PT5880 GAS LEAKAGE PRESS.
5589 13090 -GAS-: SF METHANE NUMBER
5590 13091 -GAS-: SF LAMBDA FLAP POSITION
5591 13092 -GAS-: FAILURE GLOW PLUGS ROW A
5597 13098 -GAS-: FAILURE GLOW PLUG A1
5598 13099 -GAS-: FAILURE GLOW PLUG A2
5599 13100 -GAS-: FAILURE GLOW PLUG A3
5600 13101 -GAS-: FAILURE GLOW PLUG A4
5601 13102 -GAS-: FAILURE GLOW PLUG A5
5602 13103 -GAS-: FAILURE GLOW PLUG A6
5603 13104 -GAS-: FAILURE GLOW PLUG A7
5604 13105 -GAS-: FAILURE GLOW PLUG A8
5605 13106 -GAS-: FAILURE GLOW PLUG A9
5606 13107 -GAS-: FAILURE GLOW PLUG A10
5607 13108 -GAS-: FAILURE GLOW PLUGS ROW B
5613 13114 -GAS-: FAILURE GLOW PLUG B1
5614 13115 -GAS-: FAILURE GLOW PLUG B2
5615 13116 -GAS-: FAILURE GLOW PLUG B3
5616 13117 -GAS-: FAILURE GLOW PLUG B4
5617 13118 -GAS-: FAILURE GLOW PLUG B5
5618 13119 -GAS-: FAILURE GLOW PLUG B6
5619 13120 -GAS-: FAILURE GLOW PLUG B7
5620 13121 -GAS-: FAILURE GLOW PLUG B8
5621 13122 -GAS-: FAILURE GLOW PLUG B9
5622 13123 -GAS-: FAILURE GLOW PLUG B10
5623 13124 -GAS-: IGNITION GAS COMPRESSOR FAILURE
5624 13125 -GAS-: POWER MONITORING FAILURE
5639 13140 -GAS-: SF GLOW PLUG CURRENT MONITORING A1
5640 13141 -GAS-: SF GLOW PLUG CURRENT MONITORING A2
5641 13142 -GAS-: SF GLOW PLUG CURRENT MONITORING A3
5642 13143 -GAS-: SF GLOW PLUG CURRENT MONITORING A4
5643 13144 -GAS-: SF GLOW PLUG CURRENT MONITORING A5
5644 13145 -GAS-: SF GLOW PLUG CURRENT MONITORING A6
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 126 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5645 13146 -GAS-: SF GLOW PLUG CURRENT MONITORING A7
5646 13147 -GAS-: SF GLOW PLUG CURRENT MONITORING A8
5647 13148 -GAS-: SF GLOW PLUG CURRENT MONITORING A9
5648 13149 -GAS-: SF GLOW PLUG CURRENT MONITORING A10
5649 13150 -GAS-: SF GLOW PLUG CURRENT MONITORING B1
5650 13151 -GAS-: SF GLOW PLUG CURRENT MONITORING B2
5651 13152 -GAS-: SF GLOW PLUG CURRENT MONITORING B3
5652 13153 -GAS-: SF GLOW PLUG CURRENT MONITORING B4
5653 13154 -GAS-: SF GLOW PLUG CURRENT MONITORING B5
5654 13155 -GAS-: SF GLOW PLUG CURRENT MONITORING B6
5655 13156 -GAS-: SF GLOW PLUG CURRENT MONITORING B7
5656 13157 -GAS-: SF GLOW PLUG CURRENT MONITORING B8
5657 13158 -GAS-: SF GLOW PLUG CURRENT MONITORING B9
5658 13159 -GAS-: SF GLOW PLUG CURRENT MONITORING B10
5671 13172 -MCC-: FEEDBACK FAILURE HT-CW PUMP P002
5672 13173 -MCC-: FEEDBACK FAILURE CW FILL PUMP P031
5673 13174 -MCC-: FEEDBACK FAILURE HP-GAS COMPRESSOR C004
5674 13175 -MCC-: FEEDBACK FAILURE LUBE OIL FEED PUMP P064
5675 13176 -MCC-: FEEDBACK FAILURE INTAKE AIR PREHEATING PUMP
5676 13177 -MCC-: FEEDBACK FAILURE LUBE OIL PUMP P001
5677 13178 -MCC-: FEEDBACK FAILURE LUBE OIL FILL PUMP P012
5678 13179 -MCC-: FEEDBACK FAILURE LT-CW PUMP P025
5679 13180 -MCC-: FEEDB. FAIL. LT-CW EXPANSION TANK LEVEL SWITCH LOW
5687 13188 -GAS-: GOVERNOR A - FAILURE ANALOG OUTPUT 1
5688 13189 -GAS-: GOVERNOR A - FAILURE ANALOG OUTPUT 2
5689 13190 -GAS-: GOVERNOR A - FAILURE PICK UP 1
5690 13191 -GAS-: GOVERNOR A - FAILURE PICK UP 2
5691 13192 -GAS-: GOVERNOR A - FAILURE SYNC. FAULT 1
5692 13193 -GAS-: GOVERNOR A - FAILURE SYNC. FAULT 2
5693 13194 -GAS-: GOVERNOR A - FAILURE ANALOG INPUT 1
5694 13195 -GAS-: GOVERNOR A - FAILURE ANALOG INPUT 2
5695 13196 -GAS-: GOVERNOR A - FAILURE ANALOG INPUT 3
5696 13197 -GAS-: GOVERNOR A - FAILURE ANALOG INPUT 4
5703 13204 -GAS-: GOVERNOR A - MCU STATUS ALARM
5704 13205 -GAS-: GOVERNOR A - SYSTEM ALARM
5705 13206 -GAS-: GOVERNOR A - MCU TEMP. WARNING
5706 13207 -GAS-: GOVERNOR A - MCU TEMP. CRITICAL
5707 13208 -GAS-: GOVERNOR A - AUX POWER LOW
5708 13209 -GAS-: GOVERNOR A - INJECTOR POWER LOW
5709 13210 -GAS-: GOVERNOR A - CAN 1 RECIEVE ERROR
5710 13211 -GAS-: GOVERNOR A - CAN 2 RECIEVE ERROR
5711 13212 -GAS-: GOVERNOR A - CAN 1 PORT ERROR
5712 13213 -GAS-: GOVERNOR A - CAN 2 PORT ERROR
5721 13222 -GAS-: GOVERNOR B - FAILURE PICK UP 1
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 127 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5722 13223 -GAS-: GOVERNOR B - FAILURE PICK UP 2
5723 13224 -GAS-: GOVERNOR B - FAILURE SYNC. FAULT 1
5724 13225 -GAS-: GOVERNOR B - FAILURE SYNC. FAULT 2
5735 13236 -GAS-: GOVERNOR B - MCU STATUS ALARM
5736 13237 -GAS-: GOVERNOR B - SYSTEM ALARM
5737 13238 -GAS-: GOVERNOR B - MCU TEMP. WARNING
5738 13239 -GAS-: GOVERNOR B - MCU TEMP. CRITICAL
5739 13240 -GAS-: GOVERNOR B - AUX POWER LOW
5740 13241 -GAS-: GOVERNOR B - INJECTOR POWER LOW
5741 13242 -GAS-: GOVERNOR B - CAN 1 RECIEVE ERROR
5742 13243 -GAS-: GOVERNOR B - CAN 2 RECIEVE ERROR
5743 13244 -GAS-: GOVERNOR B - CAN 1 PORT ERROR
5744 13245 -GAS-: GOVERNOR B - CAN 2 PORT ERROR
5751 13252 -GENERATOR-: INSTANT OVERCURRENT 1 TRIP (ANSI 50-1)
5752 13253 -GENERATOR-: INSTANT OVERCURRENT 2 TRIP (ANSI 50-2)
5753 13254 -GENERATOR-: INSTANT REVERSE OVERCURRENT TRIP (ANSI 50-r)
5754 13255 -GENERATOR-: INSTANT G/N OVERCURRENT TRIP (ANSI 50-G/N)
5755 13256 -GENERATOR-: UNBALANCED LOAD TOC TRIP (ANSI 46 TOC)
5756 13257 -GENERATOR-: UNBALANCED LOAD LIMIT 1 TRIP (ANSI 46-1)
5757 13258 -GENERATOR-: UNBALANCED LOAD LIMIT 2 TRIP (ANSI 46-2)
5758 13259 -GENERATOR-: REVERSE PHASE SEQUENCE TRIP (ANSI 47)
5759 13260 -GENERATOR-: OVERVOLTAGE STEP 1 TRIP (ANSI 59-1)
5760 13261 -GENERATOR-: OVERVOLTAGE STEP 2 TRIP (ANSI 59-2)
5761 13262 -GENERATOR-: UNDERVOLTAGE STEP 1 TRIP (ANSI 27-1)
5762 13263 -GENERATOR-: UNDERVOLTAGE STEP 2 TRIP (ANSI 27-2)
5763 13264 -GENERATOR-: OVERFREQUENCY STEP 1 TRIP (ANSI 81)
5764 13265 -GENERATOR-: OVERFREQUENCY STEP 2 TRIP (ANSI 81)
5765 13266 -GENERATOR-: UNDERFREQUENCY STEP 1 TRIP (ANSI 81)
5766 13267 -GENERATOR-: UNDERFREQUENCY STEP 2 TRIP (ANSI 81)
5767 13268 -GENERATOR-: AC OVERCURRENT TMC TRIP (ANSI 51 TOC)
5768 13269 -GENERATOR-: AC OVERCURRENT STEP 1 TRIP (ANSI 51-1)
5769 13270 -GENERATOR-: AC OVERCURRENT STEP 2 TRIP (ANSI 51-2)
5770 13271 -GENERATOR-: AC OVERCURRENT STEP 3 TRIP (ANSI 51-3)
5771 13272 -GENERATOR-: AC OVERCURRENT G/N TRIP (ANSI 51-G/N)
5772 13273 -GENERATOR-: VECTOR SURGE PROTECTION TRIP (ANSI 78)
5773 13274 -GENERATOR-: STATOR EARTH PROTECTION STEP 1 TRIP (ANSI 64)
5774 13275 -GENERATOR-: STATOR EARTH PROTECTION STEP 2 TRIP (ANSI 64)
5775 13276 -GENERATOR-: STATOR EARTH PROTECTION U0 TRIP (ANSI 59N)
5776 13277 -GENERATOR-: DIFFERENTIAL PROTECTION TRIP (ANSI 87 TGM)
5777 13278 -GENERATOR-: DIFFERENTIAL PROTECTION REF TRIP (ANSI 87N)
5778 13279 -GENERATOR-: DIRECTIONAL OVERCURRENT TRIP (ANSI 67)
5779 13280 -GENERATOR-: DIRECTIONAL GND OVERCURRENT TRIP (ANSI 67G/N)
5780 13281 -GENERATOR-: REVERSE POWER 1 TRIP (ANSI 32-R1)
5781 13282 -GENERATOR-: REVERSE POWER 2 TRIP (ANSI 32-R2)
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 128 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Index Message Text
5782 13283 -GENERATOR-: FORWARD POWER 1 TRIP (ANSI 32-1)
5783 13284 -GENERATOR-: FORWARD POWER 2 TRIP (ANSI 32-2
5791 13292 -GENERATOR-: 24 V DC FAILURE
5792 13293 -GENERATOR-: 230 V AC FAILURE
5793 13294 -GENERATOR-: FUSE FAILURE
5794 13295 -GENERATOR-: EMERGENCY STOP
5795 13296 -GENERATOR-: AVR FAILURE
5796 13297 -GENERATOR-: EXCITATION CIRCUIT BREAKER TRIPPED
5797 13298 -GENERATOR-: MAIN CIRCUIT BREAKER [mcb] TRIPPED
5798 13299 -GENERATOR-: FILTER DRIVEN END SIDE DISTURBED
5799 13300 -GENERATOR-: DRIVEN END SIDE MAX. PRESSURE
5800 13301 -GENERATOR-: DRIVEN END SIDE BELOW MIN. PRESSURE
5801 13302 -GENERATOR-: DRIVEN END SIDE FLOW TOO LOW
5802 13303 -GENERATOR-: FILTER NON DRIVEN END SIDE DISTURBED
5803 13304 -GENERATOR-: NON DRIVEN END SIDE MAX. PRESSURE
5804 13305 -GENERATOR-: NON DRIVEN END SIDE BELOW MIN. PRESSURE
5805 13306 -GENERATOR-: NON DRIVEN END SIDE FLOW TOO LOW
5806 13307 -GENERATOR-: DELAYED STOP
5807 13308 -GENERATOR-: SYMAP PROTECTION DEVICE FAILURE
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 129 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.5.1 Alarm Treatment
4.5.1.1 Main Alarm List – Structure
Main Alarm List: examples for Alarms of all groups.
Cutline:
1: Field of Information 3: Alarm Groups (buttons)
2: Vertical navigation bar (function and navigation buttons)
1: Field of Information
All alarms, which are set off, are displayed within this field.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 130 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.5.1.2 Using all Functions of the Main Alarm List
By pressing the following buttons, the Main Alarm List will be displayed:
Vertical Navigation Bar Horizontal Navigation Bar
How to display Information on the Marked Alarm:
Information on the chosen Alarm-ID are displayed as follows:
• General Description
• Possible Reasons
• Corrections
1. Mark the alarm in the Main Alarm List by means of the arrow key.
2. Press the button INFO in the vertical navigation bar.
3. Screen page DETAILS – ERROR HANDLING will be displayed.
Details Error Handling. Example, Alarm-ID 10500 (ALT_Screen)
Only if the i-Symbol within the button INFORMATION is visible, it is possible to display information on the marked alarm.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 131 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Display of Information on an Alarm ID
1. Select a field with the desired Alarm ID.
Once a field is chosen, a sliding switch is displayed to select the exact ID (number of alarm).
2. Adjust the Alarm ID via the sliding switch.
Select an Alarm-ID (ALT_Screen)
Please select an Alarm ID (e.g.10504) in the display DETAILS – ERROR HANDLING.
3. Please press the button CANCEL within the field of the sliding switch.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 132 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
After this operation is done, the sliding switch disappears from the display and information on the chosen Alarm ID (e.g. 10504) will be displayed.
Information on selected Alarm-ID (ALT_Screen)
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 133 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
Please press this help symbol in the navigation bar of the menu ALARM MANAGEMENT and the screen page ALARM -TROUBLE SHOOTING will be displayed.
4.5.1.3 PLC – Troubleshooting (optional)
How to display the page PLC-Troubleshooting:
PLC-Troubleshooting
By pressing the button PLC-DIAGNOSTIC in the navigation bar of this display and the following, the display of PLC-DIAGNOSTIC shows up.
Press the adequate button in the display ALARM -TROUBLE SHOOTING. The adequate menu PLC – TROUBLESHOOTING will be displayed consequently.
When the button ABB-PLC FK 1 is pressed, a screen page with the information on error class 1 FATAL ERROR will be displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 134 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
FK1 – Fatal Error
FK2 – Serious Error
When the button ABB-PLC FK 2 is pressed, a screen page with the information on error class 2 SERIOUS ERROR will be displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 135 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
FK3 – Light Error
ABB-PLC PLC - LEDs
When the button ABB-PLC FK 3 is pressed, a screen page with the information on error class 3 LIGHT ERROR will be displayed.
When the button ABB-PLC PLC-LED`s is pressed, a screen page with the information on PLC-LED`s will be displayed.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 136 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.5.1.4. Override Mode (Ship application)
DANGER
Total Loss due to Operating Error
The Override-Mode represses alarm messages and automatically commenced processes, such as emergency stop, automatic reduction of the engine and disengaging of the clutch. Any manual operated process is taken at one’s own responsibility during Override-Mode!
Never leave the display unattended!
Manual instructions have to be warranted with special caution.
The override function is only existent in case of a ship application.
Every three seconds the following display will appear with an alarm being set off, when the override-pushbutton on the operating panel is pressed:
Message during the Override-Mode – Example, current alarm
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 137 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
The override-indication contains two lines of alarm:
1. Top line of alarm: Alarms GROUP A (Automatic Shutdown -SafSys)
2. Lower line of alarm: Alarms GROUP B (Reduce -SafSyS-)
Message during the Override-Mode – Example, acknowledged alarm
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 138 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.6 Media Temperature Control
4.6.1 Lubrication Oil Temperature Control General Information
These instructions explain the usage of the lubrication oil temperature control at the
control unit JUMO Dicon 501. The corresponding software is already pre-installed by the
manufacturer and should not be modified by the user. For each software change, a
special software tool is necessary.
However, the set point at the temperature control unit is preset depending on the engine
type (65°C at 32/40; 55°C at 40/54 and 58/64; 50°C at 48/60 and 48/60B), and can be
adjusted between 15°C and 75°C.
Lube Oil Temperature Set Point Adjustment The following table shows the pushbuttons that are to be pressed successively during automatic engine operation, and the appearing display messages according to any pushbutton pressed.
The lubrication oil temperature set point is then adjusted. For further information, please refer to the JUMO operating manual B70.3580.
Pushbutton Display Notes
Standard Display (Actual Value / Set Point / Location).
1. <PGM> “W“ and the current set point are displayed in turn.
2. < > or < > “W“ and the current set point are displayed in turn.
The set point can be changed between 15°C and 75°C.
3. <ENTER> “W“ and the current set point are displayed in turn.
Instead of pressing <ENTER>, a few seconds waiting time is possible.
4. <EXIT/Hand> Standard Display (Actual Value / Set Point / Location).
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 139 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.6.2 HT Cooling Water Temperature Regulation General Information
The following instructions explain the usage of the HT temperature control at the control unit JUMO Dicon 501. The corresponding software is already pre-installed by the manufacturer and should not be modified by the user. For each software change, a special software tool is necessary. However, the set point at the temperature control unit that is preset to 90°C can be adjusted according to the following steps. HT CW Temperature Set Point Adjustment The following table contains the pushbuttons of the JUMO Dicon 501 control unit and the display messages that appear as a reaction to the activation of any pushbutton.
Pushbutton Display Notes
Standard Display (Actual Value / Desired Value / Location).
1. <PGM> “W“ and the current set point before engine (calculated by control system) are displayed in turn.
2. <PGM> “OPERATOR“
3. <ENTER> “SET POINTS“
4. <ENTER> ”W1“ and the current set point after engine are displayed in turn.
5. < > or < > “W1“ and the current set point after engine are displayed in turn.
The set point can be modified between 40°C and 95°C.
6. <ENTER> “W1“ and the current set point after engine are displayed in turn.
Alternatively to activating <ENTER>, a few seconds waiting time is possible.
7. <EXIT/Hand> “SET POINTS“
8. <EXIT/Hand> “OPERATOR“
9. <EXIT/Hand> Standard Display (Actual Value / Desired Value / Location).
For further information, please refer to the JUMO operating manual B 70.3580.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 140 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.6.3 Charge Air Temperature Regulation (CHATCO) The charge air temperature set point is calculated automatically by the temperature-controlling unit, depending on the ambient air temperature (1TE6000). The operator has access to the set point memory spaces W1 to W4, but must not modify the included and pre-set values. In case of such a modification, the entire charge air temperature control function would be endangered. For further information, please refer to the JUMO operating manual B 70.3580.
4.6.4 LT Cooling Water Temperature Regulation General Information
The following instructions explain the usage of the LT cooling water temperature control at the control unit JUMO Dicon 501. The corresponding software is already pre-installed by the manufacturer and should not be modified by the user. For each software change, a special software tool is necessary. The set point at the temperature control unit is preset to 32°C. However it can be adjusted between 20°C and 40°C, according to the following steps listed in the table below. The table also shows the display messages that appear on the JUMO control unit responding to the activation of any pushbutton. The pushbuttons are to be actuated successively.
Pushbutton Display Notes
Standard Display (Actual Value / Desired Value / Location).
1. <PGM> “W“ and the current set point are displayed in turn.
2. < > or < > “W“ and the current set point are displayed in turn.
The set point can be modified between 20°C and 40°C.
3. <ENTER> “W“ and the current set point are displayed in turn.
Instead of pressing <ENTER>, a few seconds waiting time is possible.
4. <EXIT/Hand> Standard Display (Actual Value / Desired Value / Location).
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 141 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
The LT set point is then adjusted. In case of a more complex adjusting process (e.g. with HT), a direct access to, and change of the set point memory spaces W1-W4 instead of the set point itself is possible. The current set point then complies with the memory space W1; W2-W4 are ignored by the program.
For further information, please refer to the JUMO operating manual B70.3580.
4.7 Engine Stop Several panels depending to the selected control station in progress can actuate engine stop. In each case by actuating an engine stop, the engine will be stopped immediately without any de-loading ramp controlled by SaCoS. So before actuating an engine stop be aware that the engine is unloaded. The engine stop sequence is controlling post-lubrication and post-cooling.
Confirm Engine Start / Stop
How to Start or Stop the Engine:
This button is only activated if authorised operation is given. Press the button ENGINE START / STOP in the main menu. The menu ENGINE START / STOP SEQUENCE will be displayed.
The text messages in the picture above show that the start is blocked. The start blockings can be displayed with the active button SHOW BLOCKINGS to display the current alarm. In the menu the following functions are available by means of the buttons displayed:
- Start/Stop - Reset - Show Blockings - Confirmation - Acknowledged Engine Manually Turned
If the engine is running, please press the button to stop the engine. The corresponding messages are shown on the display.
GEEA
User Manual
SaCoS 99E
Created: 26.07.2007 Rauberger This document is property of MAN Diesel SE and is entrusted to those to whom MAN has handed it. Copying and handing over to third parties is only permitted with written consent of MAN Diesel SE!
Page 142 of 143 Last Change: 20.11.2009 Karger Released: 20.11.2009 Kraus
Userm
anualS
99E
_1.3
.doc
4.8 Temporary Engine Close-down Please refer to the correspondent engine manuals, the auxiliary systems and the power supply unit about an temporary engine close-down.