user manual – bpms tp...
TRANSCRIPT
(n)Code Solutions
User Manual – TP Client
User Manual TP Client
Confidential @ (n)Code Solutions Page | 1
Document Information
Document Name User Manual – TP Client
Released Version 1.1
Released Date 24-01-2018
Document Revision History
Version Author Date Changes
incorporated
Reviewed
By
Review
Date
0.1 Tejaswini
Thalange 30-04-2017 Draft Document
Pravin
Lokhande 22-05-2017
0.2 Rupali
Karnik 23-05-2017
Formatted document
to a new template
Pravin
Lokhande 23-05-2017
0.3 Tejaswini
Thalange 17-07-2017
Made changes to
the manual Rupali Karnik 20-07-2017
0.4 Uday patil 24-07-2017 Made changes to
the manual Rupali Karnik 25-07-2017
1.0 Rupali
Karnik 30-07-2017
Released
Document
Pravin
Lokhande 30-07-2017
1.1 Akshay
Solkar 23-01-2018
Made
Changes to
manual
Pravin
Lokhande 24-01-2018
Disclaimer: This document contains proprietary confidential information to be used solely for the project
Building Plan Management System across ULBs in State of Maharashtra, by accepting this document, agrees
that neither this document nor the information disclosed herein, nor any part thereof, shall be reproduced or
transferred to other documents, or used or disclosed to others for any purpose other than the project.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 2
Table of Contents
1 Document Outline .........................................................................................5
1.1 About Drawing Protocol Document .............................................................. 5
1.2 How to read this Document ........................................................................ 5
2 Drawing Pre-formatting Utility (TP Client) ....................................................6
2.1 Overview ................................................................................................. 6
2.2 Aims & objectives...................................................................................... 7
2.3 Salient features ........................................................................................ 7
2.4 Benefits of TP Client .................................................................................. 8
2.5 Drawing formats ....................................................................................... 8
2.6 Protocol details ....................................................................................... 10
2.7 Installation and Registration ..................................................................... 11
2.8 Installation ............................................................................................. 11
3 Methodology ............................................................................................... 13
4 TP Client Layer Information ........................................................................ 19
4.1 Layer: Mark Sub Division Boundary. (TP Client-subdivision-Boundary) ........... 19
4.2 Layer: Mark Amalgamation Boundary. (TP Client-Amalgamation-Boundary) .... 20
4.3 Layer: Mark Plot Boundary. (TP Client-PlotBoundary)/Mark Sub Plot Boundary
(TP Client-Subplotboundary) .................................................................... 21
4.4 Layer: Create Plot Side. (TP Client-Front-Line)/Create Sub Plot Side (TP Client-
SubFront-Line) ....................................................................................... 23
4.5 Layer: Mark Reserve Area ........................................................................ 24
4.6 Layer: Mark Existing Structure Demolished ................................................ 25
4.7 Layer: Mark Drainage Line ....................................................................... 26
4.8 Layer: Mark Ramp ................................................................................... 27
4.9 Layer: Mark Open Space/ Recreational G Open Space .................................. 28
4.10 Layer: Mark Amenity Area ........................................................................ 30
4.11 Layer: Mark Building in Plot ...................................................................... 31
4.12 Layer: Mark Basement Parking Area or Mark Stilt/Podium Parking Area or Mark
Open Parking Area. ................................................................................. 31
4.13 Layer: Mark Column ................................................................................ 32
4.14 Layer: Mark Compound Wall ..................................................................... 33
4.15 Layer: Mark Exit/ Entrance Gate ............................................................... 34
User Manual TP Client
Confidential @ (n)Code Solutions Page | 3
4.16 Layer: Mark Substructure ......................................................................... 34
4.17 Layer: Mark Electrical Line ....................................................................... 35
4.18 Layer: Place Tree /Place Fire Alarm ........................................................... 36
4.19 Layer: Mark Helipad ................................................................................ 36
4.20 ROAD - Layer: Mark Main Road ................................................................. 36
4.21 Layer: Mark Internal Road/ Mark Internal DP Road ...................................... 37
4.22 Layer: Mark Road Widening ...................................................................... 38
4.23 How to draw ........................................................................................... 38
4.24 Layer: Mark Pathway ............................................................................... 39
4.25 BUILDING - Layer: Mark Building Boundary ................................................ 40
4.26 Layer: Mark Floor Boundary ..................................................................... 41
4.27 Layer: Mark Reference ............................................................................. 42
4.28 Layer: Mark Solar ................................................................................... 42
4.29 Layer: Mark Rain Water Harvesting Tank/ Mark OHT / Mark UGR / Mark Solar.43
4.30 Layer: Mark Parking ................................................................................ 43
4.31 Layer: Draw Section View ........................................................................ 44
4.32 FLOOR - Layer: Mark FSI Residential/ Commercial / Industrial ...................... 45
4.33 Layer: Mark Carpet Area .......................................................................... 46
4.34 Layer: Mark Room ................................................................................... 47
4.35 Layer: Mark Kitchen / Mark Toilet / Mark WC / Mark Bathroom ..................... 48
4.36 How to draw ........................................................................................... 48
4.37 Layer: Mark Balcony ................................................................................ 49
4.38 Layer: Mark Terrace ................................................................................ 50
4.39 Layer: Mark Head Room ........................................................................... 50
4.40 Layer: Mark Mezanine .............................................................................. 51
4.41 Layer: Create Door/ Ventilation /Window ................................................... 51
4.42 Layer: Mark Passage/Corridors/Lobby ........................................................ 52
4.43 Layer: Mark Escalators ............................................................................ 53
4.44 Layer: Mark Lift ...................................................................................... 54
4.45 Layer: Mark Duct/ Mark Void / Mark Ventilation Shaft .................................. 55
4.46 Layer: Mark Arch. Projection ..................................................................... 56
4.47 Layer: Mark Stair Case ............................................................................ 56
4.48 Layer: Mark Tread/ Mark Mid Landing / Mark Floor Landing .......................... 57
User Manual TP Client
Confidential @ (n)Code Solutions Page | 4
4.49 Layer: Mark Refuge Area .......................................................................... 58
User Manual TP Client
Confidential @ (n)Code Solutions Page | 5
1 Document Outline
1.1 About Drawing Protocol Document
Urban Development Department has planned to automate the building plan
approval process by introducing TP Client system. TP Client software reads the CAD
drawings submitted by architects and automatically produce the deviation report
based on the control regulations prescribed by UDD.
The purpose of this document is to establish a set of guidelines to Architects for
preparation of drawings to be submitted for taking Building Permission from UDD,
Uniformity in the process of drafting of the drawings to be submitted for approval
is required for automation of building approval system by introducing TP Client
system.
The consultants/Architects should prepare the drawings keeping specific objects in
specific layers with specific colors and text. The layers required to be generated
with explanation of what is required to be drawn on which layer is described in this
document. This document serves as a source of information on obtaining level of
consistency in drafting and approval process focuses on both the theoretical and
practical description of process flow and protocol to be used while preparing
drawings for submission at UDD for Building Permission. The document explains
use of TP Client utility
1.2 How to read this Document
This document should be read in conjunction with the Development Control
Regulations which will be applicable for approval of a proposal. The reader of this
document should have understood the applicable DCR for scrutiny of a proposal.
The reader should also be familiar with AutoCAD / ProgeCAD terminology and
environment for better understanding of the system. It is more exploratory in
nature than the specifications and contains sections to explain particular aspect of
planning and designing.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 6
2 Drawing Pre-formatting Utility (TP Client)
2.1 Overview
DCR is a unique and innovative approach to automate scrutiny of building proposals
by reading CAD drawings. TP Client software needs preformatted drawings with
some specifications. TP Client is a software application used to create the
architectural plan as per DCR software requirements. It helps in standardization of
drawings and helps in reducing time required for preparing submission drawings.
It works under AutoCAD / ProgeCAD environment with additional menu
Using TP Client commands, user can create all the required layers. Once all the
layers are created in the drawing user can use AutoCAD / ProgeCAD commands
to draw entities on the corresponding layers with the help of TP Client software.
Short commands are provided to activate /layer in TP Client. TP Client also helps
in correcting drafting errors in the drawing by displaying error in command line.
TP Client will highlight all the failed entities if any in command line.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 7
2.2 Aims & objectives
To bring uniformity and standardization in submission drawing format.
To create error free drawing by auto-correction of drafting errors.
To Increase drafting speed and efficiency
To reduce drawing data redundancy.
To remove dimensioning and area calculation requirements from
submission drawing format and auto-calculating areas in DCR
automatically.
2.3 Salient features
Automatic insertion of required text in the drawing.
Automatically inserting entities of required size in the drawing: User can mark then
enter name of field then automatic size will get created.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 8
TP Client verifies and will highlight failed entities by giving Popup when clicked
on “Validation Tool”
2.4 Benefits of TP Client
Standardization of submission drawings-Brings uniformity &
standardization in submission drawing format. This software will correct
some minor drafting errors and also provide list of failed entities with
Hardship facility so that user can easily locate the failed entities in the
drawing.
Increased speed and efficiency-TP Client facilitates Auto insertion of
many drawing entities like parking. Auto-dimensioning and auto-
calculation facility saves calculation efforts. Using this software user can
create all the required layers.
Accuracy - Accuracy in area calculations is achieved. Preparing
Calculation tables, showing dimensions in the drawing is not required.
2.5 Drawing formats
1) Conventional submission drawing format
User Manual TP Client
Confidential @ (n)Code Solutions Page | 9
2) As per TP Client format specified by TP Client
3) After Generation of drawing using DCR-
User Manual TP Client
Confidential @ (n)Code Solutions Page | 10
2.6 Protocol details
TP Client is a software application used to create the architectural plan as per
DCR requirements. It works under AutoCAD / ProgeCAD environment with
additional menu & toolbar. Using TP Client commands user can create all the
required layers. Once all the layers are created in the drawing user can use CAD
commands to draw layout plan. As per DCR requirement all building items like
proposed plot, proposed work should be drawn on the corresponding layers. Short
commands are provided to activate any layer in TP Client At any time. TP Client
will highlight all the failed entities if any in command line. TP Client can be used to
modify/make and verify the existing or new architectural plan as per DCR software
requirements. Users are free to use CAD commands and or TP Client commands to
achieve the main purpose which is:
Drawing the architectural plan in DWG format as per DCR
requirements. For automating the process of Development Control
Regulations user/draughtsman/architect have to follow some
specifications. The following are the list of specifications that the user
should follow. Site Plan, Layout Plan, Building Plan, Service Plan should
be there in one CAD drawing file.
All building items like proposed plot, proposed work, proposed parking
etc must be drawn using closed polyline. (i.e. Every entity must be closed
LWPOLYLINE except Drain line, Water Line, Electric Line, Dead Wall ).
Building Sub-Items must be exactly inside of outer closed polygon
as per their place in architectural plan. This means none of the edge
or vertex of inside entity should be drawn outside its container entity.
For example Parking or Open Space poly must be exactly inside the main
plot poly.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 11
Every Building Sub-Items should be given a specific/unique name (Text or
MText entity) on the same layer & inside the entity poly. Automatically
Naming Conventions should be followed by entering text for command
enter Name.
Floor Name: GROUND FLOOR; TYPICAL FLOOR 1, 2 & 5; TERRACE
FLOOR
Floor Items: Room Names should be given properly without using
abbreviations so the software can identify perfect entity. This can be
done by Assign name facility provided by the software.
User shall use only following kind of entities for Building Items: -
LWPOLYLINE / TEXT / MTEXT
If in a plan two proposed work are mirrored in that case user should
provide two separate building plans for each proposed work.
2.7 Installation and Registration
System Requirements
Sl.
No.
Details Minimum Configuration
Requirement
1 Processor 2.2 GHz
2 RAM 3 GB or more
3 HDD 20 GB free HD space
4 OS Windoxs XP, 7, 8
5 Internet Connectivity 1 mbps or more
6 Software Required Winrar
7 No. of Systems 1 for each user of Application
8 AutoCAD /Proge CAD Version above 2013
2.8 Installation
To install TP Client software on your computer please follows the given steps.
Step 1: After online registration, on users login the setup of TP Client will
be available, Download it.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 12
Step 2: Run the TP Client installer by double clicking on file "TP
Client_Installer.exe".
Step 3: Follow the next steps in installer wizard to complete installation.
Step 4: After installation the user should in put the valid Security code to
run the application.
After successful installation, a TP Client shortcut will be placed on your computer
desktop as shown below.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 13
3 Methodology
Open the TP Client software by clicking on TP Client menu on your
desktop & login by Enter Valid Email Id & Password Which used for
Online, while registration.
Enter Unique Code which you have received trough SMS & Email.
Fill All Forms According to Drawing & Documents.
Project Information:
User Manual TP Client
Confidential @ (n)Code Solutions Page | 14
Project Details:
Project Details:
Click on Plot Area Details tab which is present on Project Details new window will
get open were you can fill all your plot area details, Multiple Details of plot can also
be filled by using Add New button.
Select the Drop downs as per your Drawing, Selection of Area Name & CTS no is
compulsory because rate is calculated on bases of CTS No.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 15
Project Details:
Click on Client & Site Details tab which is present on Project Details new window
will get open were you can fill all your Client & Site Details, Multiple Details of Client
& Site Details can also be filled by using Add New button.
Building Details:
User Manual TP Client
Confidential @ (n)Code Solutions Page | 16
Right click on Building Type which is present on left side of application
(Tree) & click on Add to add building or click on remove to remove building.
Once clicked on add this window will get open, fill the details as per your
drawing.
Floors Details:
Right click on Typical Floor which is present on left side of application (Tree) & click on
Add to add Floor or click on remove to remove Floor.
Once clicked on add this window will get open, fill the details as per your drawing.
In Tab - Specify Floors with Identical plan & BUA Poly line user need to add floor number
as for basement = -1, Ground= 0, First=1 etc. if there are similar floors then eg. For such
cases is given below.
Eg: of Basement Floor.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 17
Eg: Ground Floor
Eg: Typical Floor
User Manual TP Client
Confidential @ (n)Code Solutions Page | 18
Floor Arrangements
Click on Map to list tab then atomically the floors will get added.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 19
4 TP Client Layer Information
4.1 Layer: Mark Sub Division Boundary. (TP Client-subdivision-
Boundary)
Description
In Subdivision one plot is divided into more than one Subdivision. All entities having
subdivision as their container entity should be uniquely present in all Subdivisions
of a Plot i.e. suppose there is a road widening in the Plot then the poly of road
widening should be different for each Subdivision (subdivided plot). Ex. Here Plot
1 is divided into three Subdivisions. And also the Road Widening is divided into
RoadW 1 and RoadW 2 for each Subdivision. (for subdivision, draw plot 1 on plot
layer and subdivided plots like SubDiv 1,SubDiv 2 & SubDiv 3 on sub-division layer
overlapping plot 1.)
Shortcut Command: SDB
How to draw
Subdivision:
Following rules will be applied on the objects of Subdivision layer
Name
Plot area
Recreation ground
Amenity
Road Widening
Pathway
Internal road
Main road
Reserve area
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
If this polyline has not been drawn and named correctly then all above
rules will not get checked.
Process -
Click on the layer Mark Sub Division Boundary.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 20
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Draw & Enter name to it.
Amalgamation
4.2 Layer: Mark Amalgamation Boundary. (TP Client- Amalgamation-Boundary)
Description:
Draw a continuous poly around the plots you want to amalgamate.
Amalgamation contains more than one plot amalgamated together. All entities
having amalgamation as their container entity should be uniquely present in each
amalgamation.I.e. suppose there is a road widening in the Plot then the poly of
road widening should be different for each amalgamation. (For amalgamation, draw
plot 1, plot 2, plot 3 on plot layer and amalgamated plot Amal Plot 1, on
amalgamation layer overlapping plot
Shortcut Command: AB
How to draw:
Following rules will be applied to Amalgamation layer
Name
User Manual TP Client
Confidential @ (n)Code Solutions Page | 21
Recreation ground
Amenity
Road Widening
Pathway
Internal road
Main road
Reserve area
Precautions to be taken –
Draw polyline correctly
Give name to this object in same layer as that of object.
If this polyline has not been drawn and named correctly then all above
rules will not get checked.
Process -
Click on the layer Mark Amalgamation Boundary.
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Draw & Enter name to it.
4.3 Layer: Mark Plot Boundary. (TP Client-PlotBoundary)/Mark
Sub Plot Boundary (TP Client-Subplotboundary)
User Manual TP Client
Confidential @ (n)Code Solutions Page | 22
Description:
Draw a Plot poly as a closed polyline which is a parcel or piece of land enclosed by
definite boundaries. A Plot will contain all Proposed Works (buildings, wings), open
space, Internal Roads, Parking etc. The overall Plot Entity represent a Plan,
AutoDCR refers it as 'Layout Plan'. The overall Plot Entity represent a Plan, AutoDCR
refer it as "Layout Plan".
Shortcut Command:Mark plot Boundary - PB / Mark Sub Plot Boundary - SP
How to draw:
Following rules will be applied to main plot layer
Size plot area
Permissible FSI
Requirement of Amenity
Requirement of Recreational ground
Requirement of Internal road, etc.
Precautions to be taken –
Draw a closed poly line correctly with text on same layer.
Provide Main access road overlapping with main plot.
Provide R.G, Amenity, reserve area, Road Widening, etc. inside Plot
boundary
Process –
Click on the layer Mark Plot Boundary.
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Draw & Enter name to it.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 23
4.4 Layer: Create Plot Side. (TP Client-Front-Line)/Create Sub Plot Side (TP Client-SubFront-Line)
Description:
Draw a Plot poly as a closed polyline which is a parcel or piece of land enclosed by
definite boundaries. A Plot will contain all Proposed Works (buildings, wings), open
space, Internal Roads, Parking etc. The overall Plot Entity represent a Plan,
AutoDCR refers it as 'Layout Plan'. The overall Plot Entity represent a Plan, AutoDCR
refer it as "Layout Plan".
Shortcut Command:
Create plot front side boundary PFS
Create plot rear side boundary PRS
Create plot left side boundary PLS
Create plot right side boundary SPB
SP
Create sub plot front side boundary SFS
Create sub plot rear side boundary SRS
Create sub plot left side boundary SLS
Create sub plot right side boundary SRS
User Manual TP Client
Confidential @ (n)Code Solutions Page | 24
How to draw:
Following rules will be applied to main plot layer
Size plot area
Permissible FSI
Requirement of Amenity
Requirement of Recreational ground
Requirement of Internal road, etc.
Precautions to be taken –
Draw a closed poly line correctly with text on same layer.
Provide Main access road overlapping with main plot.
Provide R.G, Amenity, reserve area, Road Widening, etc. inside Plot
boundary
Process –
Click on the layer Mark Plot Boundary.
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Draw & Enter name to it.
4.5 Layer: Mark Reserve Area
Description:
Reserved area (Reservation area in Development plan) shall be drawn on this layer
if present in proposal. This can be any area reserved for/by Authority for future.
Shortcut Command: RA
How to draw:
Following rules will be applied to Reserve Area layer
Reserve area
Deduction
Precautions to be taken –
User Manual TP Client
Confidential @ (n)Code Solutions Page | 25
Draw polyline correctly
Give name to this object in same layer as that of object
If this polyline has not been drawn and named correctly then all above
rules will not get checked
Process –
Click on the layer Mark Reserve Area.
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Draw the area.
4.6 Layer: Mark Existing Structure Demolished
Description:
Draw a structure which already approved by authority as a closed poly. And mark
this as 'To be demolished' by using Mark option from TP Client Menu.
Shortcut Command: SD
How to draw:
Following rules will be applied on the objects of Existing Structure Demolished layer
Existing coverage area
Existing built up area
User Manual TP Client
Confidential @ (n)Code Solutions Page | 26
Precautions to be taken –
Draw poly line properly and give a text and Mark “To be Demolished”
Process –
Click on the layer Existing Structure Demolished.
In Command line – Select Option for Creating Area (Rectangle/ Draw/ select/
Boundary)By selecting these options the user can trace the drawing,
Rectangle[r] is used when the plot is of rectangle shape, Draw is used when
plot is irregular, Select [s] is used when ploy-line is present, Boundary [b] is
used when ploy-line is present.
Draw the area.
4.7 Layer: Mark Drainage Line
Description:
Draw unclosed poly line for drainage line
Shortcut Command: DL
User Manual TP Client
Confidential @ (n)Code Solutions Page | 27
How to draw:
Process –
Click on the layer Mark Drainage Line.
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Draw unclosed line.
Layer: Mark Water Line
Description: Draw unclosed line for water line
Shortcut Command: WL
How to draw: Process –
Click on the layer Mark Water Line.
In Command line – Select Option for Creating Area (Rectangle/ Draw/ select/ Boundary)By selecting these options the user can trace the drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw is used when plot is irregular, Select [s] is used when ploy-line is present, Boundary [b] is used when ploy-line is present.
Draw unclosed line.
4.8 Layer: Mark Ramp
User Manual TP Client
Confidential @ (n)Code Solutions Page | 28
Description:
Draw a Ramp poly as a closed polyline in floor plans and/or plot. Naming convention
for ramp is "---m. long and ---m.
Shortcut Command: MR
How to draw:
Following rules will be applied on the objects of Ramp layer
Width
Slope
Process –
Click on the layer Mark Ramp.
Give width of ramp in „m‟
Specify 1st point specify last point – Note should be marked from center
to center of ramp & enter.
Enter start level height in „m‟ & End level height in „m‟.
4.9 Layer: Mark Open Space/ Recreational G Open Space
Description:
Draw Recreational Ground as closed polyline reserved as open space/ recreational
space on this layer.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 29
Shortcut Command: ROS
How to draw:
Following rules will be applied on the objects of recreational ground layer
Balance plot
Deduction in area calculation
Minimum recreation ground area/ open space
Plot area in side recreation ground
Precautions to be taken –
Draw polyline correctly
If this polyline has not been drawn correctly then all above rules will not
get checked
Process –
Click on the layer Mark Open Space/ Recreational Ground
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Draw closed line.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 30
4.10 Layer: Mark Amenity Area
Description:
Draw Amenity Area as a closed polyline which is reserve for utilities, services and
conveniences.
Shortcut Command: AA
How to draw:
Following rules will be applied on the objects of Amenity layer
Deduction
Addition
Precautions to be taken –
Draw polyline correctly.
If this polyline has not been drawn then rules will not get checked
properly.
Process –
Click on the layer Mark Amenity Area.
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Draw closed line.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 31
4.11 Layer: Mark Building in Plot
Description:
If you are getting permission for layout and containing building in it, then you need
draw building periphery of that building. In this case, tentative block of building will
refer just the presence of building in Plot.
Shortcut Command: MBP
How to draw:
Process –
Click on the layer Mark Building in Plot
In Command line – Select Option for Creating Area (Rectangle/ Draw/ select/
Boundary)By selecting these options the user can trace the drawing,
Rectangle[r] is used when the plot is of rectangle shape, Draw is used when
plot is irregular, Select [s] is used when ploy-line is present, Boundary [b] is
used when ploy-line is present.
Draw closed line & name it.
4.12 Layer: Mark Basement Parking Area or Mark Stilt/Podium
Parking Area or Mark Open Parking Area.
Shortcut Command: Mark Basement Parking Area – BPA/ Mark stilt/
podium parking area- SPP Mark open parking area -OPA
User Manual TP Client
Confidential @ (n)Code Solutions Page | 32
How to draw:
Process –
Click on the layer Mark Basement Parking Area & Mark Stilt/Podium
Parking Area & Mark Open Parking Area.
In Command line – Select Option for Creating Area (Rectangle/ Draw/ select/
Boundary)By selecting these options the user can trace the drawing,
Rectangle[r] is used when the plot is of rectangle shape, Draw is used when
plot is irregular, Select [s] is used when ploy-line is present, Boundary [b] is
used when ploy-line is present.
Draw closed line.
4.13 Layer: Mark Column
Description:
Draw each column as closed poly line on “Column” layer inside parking floor as well
as inside and overlapped with Building line layer in other floors.
Shortcut Command: MC
How to draw:
Process –
Click on the layer Mark Column
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Draw closed line.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 33
4.14 Layer: Mark Compound Wall.
Description:
Draw poly line of compound wall to be drawn on proposed compound wall with text
started with compound wall height. E.g. 1.5m. High Compound Wall
Shortcut Command: CW
How to draw:
Following rules will be applied to Compound Wall
Height
Precautions to be taken –
Draw a closed poly line correctly.
Process –
Click on the layer Mark Compound Wall.
In Command line – Select Option 1.Front/2.Rear/3.Side
Enter wall width in ‘m’
User Manual TP Client
Confidential @ (n)Code Solutions Page | 34
Specify 1st & last point.
Enter Height in ‘m’.
4.15 Layer: Mark Exit/ Entrance Gate
Description:
Draw Closed ploy line for Mark Exit/Entrance Gate.
Shortcut Command: EG
How to draw:
Process –
Click on the layer Mark Exit/Entrance Gate.
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Enter height in meter eg:2.1m.
4.16 Layer: Mark Substructure.
Description:
Draw closed ploy line for Mark Substructure.
Shortcut Command: SS
User Manual TP Client
Confidential @ (n)Code Solutions Page | 35
How to draw:
Process –
Click on the layer Mark Substructure.
In command line all options will get display such as 1.Electrical Room/2.
Transformer Room etc. by selecting 1,2,3,4 etc you can select the point
which you want to mark.
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
4.17 Layer: Mark Electrical Line
Description:
Draw unclosed line for electrical line
Shortcut Command: EL
How to draw:
Process –
Click on the layer Mark Electrical Line.
In Command line – Select Option for Creating Area (Rectangle/ Draw/ select/
Boundary)By selecting these options the user can trace the drawing, Rectangle[r] is used
when the plot is of rectangle shape, Draw is used when plot is irregular, Select [s] is used
when ploy-line is present, Boundary [b] is used when ploy-line is present.
Draw unclosed line.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 36
4.18 Layer: Place Tree /Place Fire Alarm
Description:
Pick the point where you want to place it.
Shortcut Command: Place Tree - PT/ Place Fire Alarm- PFA
4.19 Layer: Mark Helipad
Description:
Draw closed ploy line where you want to mark the Helipad it is allowed only in High
rise structure.
Shortcut Command: MHP
How to draw:
Process –
Click on the layer Mark Helipad.
In Command line – Select Option for Creating Area (Rectangle/ Draw/
select/ Boundary)By selecting these options the user can trace the
drawing, Rectangle[r] is used when the plot is of rectangle shape, Draw
is used when plot is irregular, Select [s] is used when ploy-line is
present, Boundary [b] is used when ploy-line is present.
Draw closed ploy line.
4.20 ROAD - Layer: Mark Main Road
Description:
Draw road with text specifying its width and draw a center line of road.
Shortcut Command: MMR
How to draw:
Process –
Following rules will be applied
Width
Length
Precautions to be taken –
User Manual TP Client
Confidential @ (n)Code Solutions Page | 37
Draw a unclosed poly line correctly and give text of width of road on
command line eg: - 9 m.
Draw main Road in front of Front Margin, marking main road is import to
get proper permissible building height.
4.21 Layer: Mark Internal Road/ Mark Internal DP Road.
Description:
Draw existing or proposed D. P. (Development Plan) road or T. P. (Town
Planning) Road when inside/intersected with plot. Give road width of
road. E.g. 9m wide D. P. Road.
Shortcut Command: IR/IDR
How to draw:
Process –
Internal DP Road:
Following rules will be applied
Width
Precautions to be taken –
Draw unclosed poly line correctly and give width of road on same layer.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 38
4.22 Layer: Mark Road Widening
Description:
Draw a road widening polyline as a closed polyline which the plot area is
going to the road, that area should be drawn on this layer. It should be
inside the plot polyline.
Shortcut Command: RW
4.23 How to draw:
Road Widening:
Following rules will be applied to Road Widening layer
Calculation of net Plot
Widening of Road
Precautions to be taken –
Draw a closed poly line correctly inside Main plot and give text on same
layer.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 39
4.24 Layer: Mark Pathway
Description:
Draw Pathway as a unclosed polyline with text specifying its width.eg.1.5
m. wide pathway.
Shortcut Command: PW
How to draw:
Pathway:
Following rules will be applied on the objects of Pathway layer
Length
Width
Precautions to be taken –
Draw polyline correctly
Give width to this object in same layer as that of object
User Manual TP Client
Confidential @ (n)Code Solutions Page | 40
If this polyline has not been drawn and named correctly then all above
rules will not get checked
4.25 BUILDING - Layer: Mark Building Boundary.
Description:
Draw rectangle around by considering all the Floor plans, Section &
elevation, site plan etc. so that while generating the floors get identified,
eg Ground floors details get identified.
Shortcut Command: BB
How to draw:
Draw rectangle around the considering whole drawing so that it get
identified while generating.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 41
4.26 Layer: Mark Floor Boundary.
Description:
Draw rectangle around single floor as shown in below eg. Draw rectangle
considering all components of ground floor then mark it.
Shortcut Command: FB
How to draw:
Draw rectangle around each floor considering all the items of that floor,
for each floor differently.
After making it will ask to select building then select the outer building
boundary.
Then select from drop down which floor it is eg: Ground Floor, First Floor
etc.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 42
4.27 Layer: Mark Reference
Description:
Put reference point on staircase corner on every floor it should be on
same point as of fist floor you have marked. It help in Auto creating 3D
drawing.
Shortcut Command: REF
How to draw:
Pick the point on each floor which you want to refer.
Careful while selecting same corner should get selected on each floor
then only auto 3D gets created & follow the steps in command line.
4.28 Layer: Mark Solar
Description:
A closed polyline to represents Solar. Solar can be drawn in TERRACE
FLOOR. It should be drawn as per internal size or dimensions.
Shortcut Command: MS
How to draw:
Draw on the floor where it is located by giving its proper capacity in
liters.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 43
4.29 Layer: Mark Rain Water Harvesting Tank/ Mark OHT / Mark
UGR / Mark Solar.
Description:
A closed polyline on _Tank layer represents a water tank. Under Ground
tank can be drawn in Floor or Layout plan. If it is drawn in Floor plan
then it should be at bottom of GROUND FLOOR. Overhead tank can be
drawn in TERRACE FLOOR. Tank should be drawn as per internal size or
dimensions. Both the tank also draws in section also.
Shortcut Command: Rain Water Harvesting Tank -RWH /Mark
OHT - OHT / Mark UGR- UGR / Mark Solar- MS
How to draw:
Following rules will be applied on the objects of Tank layer
Tank area
Width
Depth
Capacity
Precautions to be taken –
Draw closed poly line properly and give capacity of tank.
If this polyline has not been drawn correctly then all above rules will not get check.
4.30 Layer: Mark Parking.
Description:
Pick the point where you want to place the vehicles select the vehicle
type from command line, once you select the type eg: Car, then auto
rectangle of standard size of car gets created.
Shortcut Command: PAR
How to draw:
Parking:
Following rules will be applied to Parking layer
Select the type of Vehicles & pick the point where you want to mark.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 44
Precautions to be taken –
If it is not inserted correctly then no of proposed parking‟s will not come
proper.
4.31 Layer: Draw Section View
Description:
Select the building line (Yellow Rectangle) which you have already
created then pick the opposite point so that section (line Section) to
define height is created atomically.
Shortcut Command: SV
How to draw:
Section:
Following rules will be applied on the objects of Section layer
All Floors in section
Ground level
Building height
Precautions to be taken –
Follow the same process as given above for drawing line section view so
that it gives proper result.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 45
4.32 FLOOR - Layer: Mark FSI Residential/ Commercial / Industrial.
Description:
Draw a “FSI” as a closed poly line which area to be calculated for
consumption of actual Built-up of that floor excluding cantilever
projections, Natural terrace but consider balcony & Terrace so that we
can get excess terrace & balcony automatically.
Shortcut Command: Mark FSI residential-FSIR /Mark FSI commercial-
FSIC / Mark FSI Industrial - FSII
How to draw:
Pathway:
Following rules will be applied on the objects of Pathway layer
Length
Width
Precautions to be taken –
Draw polyline correctly
Give width to this object in same layer as that of object
If this polyline has not been drawn and named correctly then all above
rules will not get checked
Consider balcony & terrace will parking & then mark balcony area &
Terrace area separately so that excess values are calculated.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 46
4.33 Layer: Mark Carpet Area
Description:
Draw carpet area as a closed poly line which is a net usable floor area
within a building excluding that covered by the walls or any other areas
specifically exempted from floor space index computation in this
regulation.
Shortcut Command: CA
How to draw:
Carpet Area:
Following rules will be applied to carpet area layer
Per Carpet Tenement number check required
Tenement density
Water tank calculation
User Manual TP Client
Confidential @ (n)Code Solutions Page | 47
Precautions to be taken –
Draw poly line correctly Give text of carpet area as Floor name or flat
number etc. while creating layer to identify your carpet
If this poly line has not been drawn and named correctly then all above
rules will not get checked.
4.34 Layer: Mark Room
Description:
Draw closed polyline of Room layer represents a rooms ie. Bedroom,
Master Bedroom, other room etc. In command the rooms will display
user can select the option which room he want to select by clicking 1,
2,3etc. Then give proper text to the room by tying in command field.
Shortcut Command: ROO
How to draw:
Following rules will be applied on the objects of room layer
Click on TP Client menu Floor Mark Room
User Manual TP Client
Confidential @ (n)Code Solutions Page | 48
Once you select mark room in command line types of room get display
eg: 1. Bed room, 2. Master Bedroom etc. select 1 or 2 which ever room
you need to mark.
Then type the text you require & auto dimension (Room size, Width) will
get display with that text.
Precautions to be taken –
Draw closed poly line properly and give name to this object.
Room must be inside carpet area poly line.
4.35 Layer: Mark Kitchen / Mark Toilet / Mark WC / Mark Bathroom
Description:
Draw closed polyline of Kitchen. Then give proper text to the room by
tying in command field.
Shortcut Command: Mark Kitchen- MK /Mark Toilet- MT / Mark WC-WC /
Mark Bathroom- MB
4.36 How to draw:
Following rules will be applied on the objects of room layer
Click on TP Client menu Floor Mark Kitchen
Select mark Kitchen Draw closed poly line or select poly line to mark it.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 49
Then type the text you require & auto dimension (Room size, Width) will
get display with that text.
Precautions to be taken –
Draw closed poly line properly and give name to this object.
Kitchen room must be inside carpet area poly line.
For Mark Toilet/ Mark WC / Mark Bathroom for all these same option as
we used for kitchen should be used.
4.37 Layer: Mark Balcony
Description:
Draw closed poly line of Balcony. Select which type of balcony it is
normal or enclosed. Then give proper text to the balcony by tying in
command field.
Shortcut Command: BAL
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark Balcony
Select mark Balcony Draw closed poly line or select poly line to mark it.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 50
Then type the text you require & auto dimension of Balcony will get
display with that text.
Precautions to be taken –
Draw closed poly line properly and give name to this object.
Consider balcony in FSI line so that we can identify & calculate %
permissible & excess proposed to that floor.
4.38 Layer: Mark Terrace
Description:
Draw closed poly line of Terrace.
Shortcut Command: TERR
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark Terrace
Select mark Terrace Draw closed poly line or select poly line to mark it.
Precautions to be taken –
Draw closed poly line properly and give name to this object.
Consider Terrace in FSI line so that we can identify & calculate %
permissible & excess proposed to that floor.
4.39 Layer: Mark Head Room
User Manual TP Client
Confidential @ (n)Code Solutions Page | 51
Description:
Draw closed poly of Headroom on Terrace as headroom are placed on
terrace above staircase.
Shortcut Command: HR
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark Head Room.
Select mark Head Room Draw closed poly line or select poly line to mark
it.
Precautions to be taken –
Draw closed poly line properly and give height of headroom.
4.40 Layer: Mark Mezanine
Description:
Draw closed poly of Mezanine floor were in room it is placed.
Shortcut Command: MM
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark Mezanine.
Select mark Mezanine draw closed poly line or select poly line to mark it
in which room you want to place.
Precautions to be taken –
Draw closed poly line properly and give height of Mezanine.
4.41 Layer: Create Door/ Ventilation /Window
Description:
Door/ Ventilation /Window is a closed Polyline which is drawn on location
of window. Enter proper height when asked in command & give naming
convention as “V,W1,D1” etc
Shortcut Command: Create Door- CD/ create ventilation/window - CV
User Manual TP Client
Confidential @ (n)Code Solutions Page | 52
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor create Door/ Ventilation /Window
Select create Door/ Ventilation /Window draw closed poly line or select poly line to
mark it in which room you want to place.
Precautions to be taken –
Draw closed poly line properly and give height of Door/ Ventilation
/Window.
4.42 Layer: Mark Passage/Corridors/Lobby
Description:
Draw a closed polyline of passage/corridors/Lobby. It is a common
passage or circulation space including a common entrance hall. Select
which type of passage it is by selecting from command. Lift lobbies to be
drawn on same layer and to be marked it as Paid by using from
command.
Shortcut Command: MP
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark passage/corridors/Lobby
User Manual TP Client
Confidential @ (n)Code Solutions Page | 53
Select Mark passage/corridors/Lobby, select option from command 1.open passage or
corridors/2.covered free from Fsi/3.covered Taken in Fsi/4.Lobby you can select any of the
option by clicking 1,2,3,4 then option Rectangle/Draw/Select/Boundary will display in
command line you can select “S” & select the poly line the it will mark automatically for
Draw-D, for rectangle-r, Boundary-b can select & mark it.
Precautions to be taken –
Draw closed poly line properly.
4.43 Layer: Mark Escalators
Description:
Draw closed poly line of mark escalators this is usefully in case of malls,
huge complexes etc.
Shortcut Command: ESC
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark Escalators
Option Rectangle/Draw/Select/Boundary will display in command line you
can select “S” & select the poly line then it will mark automatically for
Draw-D, for rectangle-r, Boundary-b can select & mark it.
Precautions to be taken –
Draw closed poly line properly.
You can mark rectangle around the escalator in plan.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 54
4.44 Layer: Mark Lift
Description:
Draw closed poly line of Mark Lift.
Shortcut Command: LIF
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark Lift
Select Mark Lift, select option from command 1.Lift/2.Machine Lift/3.Fire
Lift you can select any of the option by clicking 1, 2,3.
Then option 1.Remove From Fsi /2.Taken in Fsi will display you can
select any of the option by clicking 1,2.
Then Option Rectangle/Draw/Select/Boundary will display in command
line you can select “S” & select the poly line then it will mark
automatically for Draw-D, for rectangle-r, Boundary-b can select & mark
it.
Then after typing text auto dimension will display.
Precautions to be taken –
Draw closed poly line properly.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 55
4.45 Layer: Mark Duct/ Mark Void / Mark Ventilation Shaft
Description:
Draw closed poly line of Mark Duct/Mark Void/Mark ventilation Shaft.
Shortcut Command: Mark Duct- MD / Mark Void- MV / Mark ventilation
Shaft-VS
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark Duct/ Mark Void / Mark Ventilation
Shaft.
Then Option Rectangle/Draw/Select/Boundary will display in command line you can select
“S” & select the poly line then it will mark automatically for Draw-D, for rectangle-r,
Boundary-b can select & mark it.
Then after typing text auto dimension will display.
Precautions to be taken –
Draw closed poly line properly.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 56
4.46 Layer: Mark Arch. Projection
Description:
Draw closed poly line of Mark Arch.projection.
Shortcut Command: AP
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark Mark Arch. Projection.
Select Mark Lift, select option from command
1.F.Bed/2.Chajja/3.C.B/4.loft/5.Canopy/6.Porch you can select any of
the option by clicking 1, 2,3,4,5,6.
Then Option Rectangle/Draw/Select/Boundary will display in command
line you can select “S” & select the poly line then it will mark
automatically for Draw-D, for rectangle-r, Boundary-b can select & mark
it.
Specify 1st & last point.
Then auto name will get display once you select the option.
Precautions to be taken –
Draw closed poly line properly.
4.47 Layer: Mark Stair Case.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 57
Description:
Draw closed poly line of Mark Staircase, Mark Rectangle around the plan
of staircase.
Shortcut Command: ST
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark staircase.
Select Mark Staircase, select option from command 1.Normal Staircase
/2.Spiral /3.Fire Escape Stair you can select any of the option by clicking
1, 2,3.
Then Option Rectangle/Draw/Select/Boundary will display in command
line you can select “S” & select the poly line then it will mark
automatically for Draw-D, for rectangle-r, Boundary-b can select & mark
it.
Specify 1st & last point.
Precautions to be taken –
Draw closed poly line properly.
4.48 Layer: Mark Tread/ Mark Mid Landing / Mark Floor Landing.
Description:
Draw closed poly line of Mark Tread/ Mark Mid Landing/ Mark Floor
Landing, Mark Rectangle for each Tread/ Mid Landing / Floor Landing.
User Manual TP Client
Confidential @ (n)Code Solutions Page | 58
Shortcut Command: Mark Tread - TRE / Mark Mid Landing – ML / Mark
Floor Landing - FL
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark Tread/ Mark Mid Landing/ Mark Floor
Landing.
Option Rectangle/Draw/Select/Boundary will display in command line you can select “S” &
select the poly line then it will mark automatically for Draw-D, for rectangle-r, Boundary-b
can select & mark it.
Specify 1st & last point.
Precautions to be taken –
Draw closed poly line properly.
4.49 Layer: Mark Refuge Area
Description:
Draw closed poly line of Mark Refuge Area.
Shortcut Command: RFSI
How to draw:
Following rules will be applied on the objects
Click on TP Client menu Floor Mark Refuge Area.
Option Rectangle/Draw/Select/Boundary will display in command line you
can select “S” & select the poly line then it will mark automatically for
Draw-D, for rectangle-r, Boundary-b can select & mark it.
Specify 1st & last point.
Precautions to be taken –
User Manual TP Client
Confidential @ (n)Code Solutions Page | 59
Draw closed poly line properly.