A Series Rugged, heavy duty Units for multiple hole punching andnotching. Standard 8 3/8" shut height and 3 1/2" die height.

A Series Unitsoffer you a wide range of standard holderwidths, throat depths, and round and shapedPunches and Dies. Strong stripping springsand rugged holders insure burr-free holes withminimal maintenance. Quick, accurate templatelocations and flexibility with various mountingmethods (without special equipment) are alsofeatures of the “A” Series.

AH Units punch up to 1⁄2" thickmaterials.These units feature multiple heavyduty springs that “strip” the Punchesfrom mild steel as thick as 1⁄2". Theyincorporate hardened steel bushingsthat provide long life and accuraterigid alignment of punches.

UniPunch “A” Series Units feature economical two-piece

Punches. Punch heads and bodies are separate, which lets you

quickly change hole size and shape, simply by changing the

inexpensive Punch bodies. Slip-on retainer pins hold Punches in

place without any special tools. Use and reuse the Punch Heads

indefinitely. Low-cost Die Buttons complete the Punch system and

offer close tolerances for accuracy and interchangeability.

Notching Units for materialsup to 1⁄4" th.

5" x 5" max. Corner Notches3" x 8" max. Edge Notches1", 11⁄2", and 3” Vees at 90°

FTA Units provide unrestricted throat depth. These Units punch holes in sheets where the throatdepth of standard UniPunch Units is a limiting factor. This system permits unobstructed feed of largeflat workpieces.

.

1 of 1 http://unipunch.com/aboutus/unitized.html

952-496-3335 800-333-9645 FAX 952-496-2725

sales@franciscompany.com

UniPunch Products Inc

Francis Company Inc

AJ Series For angles, channels, extrusions, and sheets.

FTA Units provideunrestricted throat depth.These Units punch holes in sheets where thethroat depth of standard UniPunch Units is alimiting factor. This system permits unobstructedfeed of large flat workpieces.

“AJ” Series Units are ideal for punching angles, extrusions, channels, and other formedparts. Interchangeable Die Buttons and Pedestal Dies provide added versatility in punchinground and shaped holes. Hardened alloy steel die adapters make The“AJ” Seriesespecially suited for tough punching applications.

Optional Pedestal Dies

Our optional Pedestal Dies are interchangeable with die adapters. With a wide range ofdiameters and configurations, they increase the versatility of the “AJ” Units and let youpunch holes in angles, channels and extrusions, easily and accurately.

Requirements when altering a Pedestal DieCommon requirements when altering a pedestal die are shown in the examples below. Usethe drawings below as a guideline to your specific application. Submit a drawing of yourpart to the UniPunch Quotations Department for cost.

1288 Altered Ped Die -FlatsRequired parameters1289 Altered Ped Die - BossRequired parametersA = Front Flat LocationB = Front Flat HeightC = Rear Flat LocationD = Rear Flat Height

E = ChamferSpecify Dia. or ShapeTDC -Total DieClearance

1289 Altered Ped Die -BossRequired parametersA = Top DiameterB = Front/Top HeightE = Chamfer - 45° unlessotherwise requested

Specify Dia. or ShapeTDC -Total DieClearance

Francis Company Inc952-496-3335 800-333-9645 FAX 952-496-2725 sales@franciscompany.com

TP Series For hole punchingin round or shaped tubes.

TP 11⁄4 & TP 23⁄8 UnitsThese units provide two sided punchingin round or square tubes. Eachassembly top and bottom contains aPunch to pierce two holes in-line oneach side of the tube. The tubing issupported on all sides during punching.If only one hole is desired, the removalof the bottom Punch accommodates thisoption. The Units require upper andlower Templates. One template isattached to the Ram of the Press, theother to the bed. A tube is placed intothe lower assembly, the Ram is thenlowered for line up adjustment, and theunits are then secured to the Templatesand are ready to punch holes. Due tolack of Die, unsupported tubes distortwhen punched.

TP-2 UnitsThis self contained ‘C’ Frame Unitutilizes pilot pins in the bottom of theholder for mounting on 1⁄2" thickTemplates with nothing attached to thePress Ram. The tubing is supported onall sides during punching. The Unitsprovide straightthrough holes with onepunch. The top hole has distortion,which varies depending upon Punchsize, tube OD, wall thickness andmaterial type. The bottom hole ispunched into a die, providing minimaldistortion.

PH. (800) 828-7061 • FAX: (800) 453-3994 • WWW.UNIPUNCH.COM

Unipunch is the Leader in Reusable Unitized Press Tooling

Search the catalog by Part No./Catalog No/Model No.:Part No./Catalog No.: - or - Model No.: - or - Page No.: Search Print This

Page

1 of 1 3/17/2011 10:34 PM

Francis Company Inc952-496-3335 800-333-9645 FAX 952-496-2725

sales@franciscompany.com

B Series Compact Units for lighter fabrication. Standard 5 1/2 " shutheight and 2 19/32" die height.

B Series Punching and Notching Units aredesigned for press equipment with limited Diespace. Round and shaped holes are availableup to 31/2" in diameter.

“B” Units also offer you a wide rangeof standard holder widths and throatdepths with round or shapedPunches and Dies. Strong strippingsprings and rugged holders insureuniform holes. Units feature quick-change Die Block retention and easydie removal.

Unipunch B Series Punches and Dies

A-2 tool steel Punches extend tool life up to 40% andare resistant to chipping and cracking.

Two-piece Punch design–have removable heads forusing “shims” to restore full length after sharpening.

Notching Units for mild steel up to10 ga. thick

5" x 5" max. Corner Notches3" x 8" max. Edge Notches1" and 11/2" 90° Vee Notches

P • FAX • . .

Unipunch is the Leader in Reusable Unitized Press Tooling

Search the catalog by Part No./Catalog No/Model No.:Part No./Catalog No.: - or - Model No.: - or - Page No.: Search Print This

Page

Francis Company Inc952-496-3335 800-333-9645 FAX 952-496-2725 sales@franciscompany.com