uncertainty in the analysis of the risk of bleve fireball in ......bleve-fireball of propane, 2000...
TRANSCRIPT
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Uncertainty in the analysis of the risk of
BLEVE – Fireball
in process plants and in transportation
Joaquim Casal
Centre for Studies on Technological Risk (CERTEC)
EEBE, Universitat Politècnica de Catalunya
CERN Workshop “An angineering perspective on risk assessment: from theory to practice”
November 2018
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Outline
- Introduction
- Uncertainties, BLEVE:
- frequency
- time to failure
- vessel pressure
- amount of material
- energy released
- peak overpressure
- ejected fragments
- Uncertainties, fireball:
- frequency
- amount of material
- Conclusions
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Introduction
BLEVE: an explosion resulting from the failure of a vessel containing a liquid (+ vapor) at a
temperature significantly above its boiling point at atmospheric pressure.
BLEVEs are just mechanical explosions. Their effects:
- overpressure wave
- ejection of fragments.
Often, substances involved in a BLEVE are flammable. In such cases, BLEVE is usually followed by a
fireball; its effect:
- thermal flux
So, many people consider BLEVE and fireball practically synonymous.
But this is not correct (example: steam boiler).
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Introduction
Survey: 202 accidents with BLEVE, 1960 – 2018 (Hemmatian et al, 2018):
Origin Nº accidents %
---------------------------------------------------------------------
Transport 87 43 (rail/road: approx. 5/4)
Storage 42 21
Process plant 33 16
Transfer 25 12.5
Other 15 7.5
202 100
---------------------------------------------------------------------
Substances involved:
LPG: 42%
water: 8% (?)
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Uncertainty: frequency
Frequency of instantaneous release of the complete inventory (not necessarily BLEVE)
--- Stationary vessels:
Atmospheric storage tank 5 · 10-6 year-1
Pressure storage vessel 5 · 10-7 year-1
Process vessel 5 · 10-6 year-1
--- Road and rail tankers in an establishment:
Atmospheric tank 5 · 10-5 year-1
Pressurized tank 5 · 10-7 year-1
[Rupture of loading/unloading hose: 4·10-6 h-1 ]
In a QRA: the frequency of the BLEVE of a vessel is obtained from the estimation of the frequency of the
scenario (pool fire, jet fire…) that will cause it.
To take into account domino effect (for ex., if there are several vessel at short distance) that frequency
can be multiplied by 2.
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
A situation that can lead to a BLEVE
If there is flame impingement on a vessel, failure is a combination of high pressure (heating of
liquid wetted wall) + wall weakening (heating of wall above liquid level).
Worst case: jet fires
Approximate heat fluxes (impingement):
natural gas, sonic: 200 kW m-2
propane gas, sonic: 300 kW m-2
propane 2-phase, sonic: 180 kW m-2
propane 2-phase, not sonic: 150 kW m-2
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Impingement below or above liquid level
(vessel 80% fill with water; Birk, 2006):
A situation that can lead to a BLEVE
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Uncertainty: frequency
Frequency in transportation
73.5% of accidents in the transportation of hazmat are originated by collisions
(Ronza et al., 2003; Linkuté, 2011).
A “common” sequence: collision release fire BLEVE.
It is not possible to predict the frequency.
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Uncertainty: time to failure
Time to failure depends on: fire heat flux
fireproofing existence/condition
vessel volume/surface ratio
wall thickness
fire exposure area
vessel fill level.
Failure can occur: in 1 min
in half an hour or more
or can never occur.
Mexico City: 67 s, 1 h, 1.5 h, neverZarzalico (Spain), 2011: 73 min
Chiba (Japan), 2011: 1 h
Tivissa (Spain), 2002: 20 min
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Possibilities:
- Operating pressure
Example: storage pressure if there is an impact.
- An intermediate pressure between the operating one and the PRV set value.
Example: a vessel being heated fails before PRV opens.
- PRV set pressure
Example: a tank heated by a fire, after a certain time PRV opens.
- A pressure higher than the PRV pressure.
Example: the device is blocked or heat flux exceeds the design conditions.
General hypotheses:
- PRV set pressure for vessels heated by a fire.
- Operating/storage pressure for impact (no fire).
Uncertainty: vessel pressure
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Uncertainty: vessel pressure / time to failure
Moodie-1/4t-40% Moodie-1t-80%
60 s 180 s 60 s 180 s
10 cm 20 cm
Scarponi, G.E., Landucci, G., Birk, A.M., Cozzani, V., 2018. LPG vessels exposed to fire:
Scale effects on pressure build-up. J. Loss Prev. Process Ind. 56, 342–358.
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Uncertainty: vessel pressure / time to failure
Scarponi, G.E., Landucci, G., Birk, A.M., Cozzani,
V., 2018. LPG vessels exposed to fire: Scale effects
on pressure build-up. J. Loss Prev. Process Ind. 56,
342–358.
The temperature stratification can
originate a quick pressure built-up,
depending on tank size and shape.
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
- Worst case: the maximum amount legally possible.
- If the explosion occurs a certain time after the valve opening, some material will have been released.
So, some authors suggest 80% or 90% of the maximum amount legally possible.
Uncertainty: amount of material
PRV reduction of pressure + reduction of content
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Two contributions:
1. Expansion of the pre-existing vapor.
2. Instantaneous vaporization of the superheated liquid
(volume increase: water, 1700 times; propane, 250 times).
Experimental DP measurements show two consecutive peaks corresponding to these two phenomena:
Uncertainty: contributions to energy released
Johnsons, Pritchard, Wickens, 1990.
5.7 m3 vessel, propane, filled 80%.
Birk et al., 2007
1.89 m3 vessel, propane, filled 51%.
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
-- Traditionally it had been assumed that the essential contribution is the one due to liquid vaporization.
-- Birk (2007, 2018) has suggested that flash vaporization is too slow to produce a shock wave, blast
being essentially created by the expansion of the previously existing vapor.
The relative magnitude of both peaks will depend on the mass fractions of liquid and vapor in the vessel
and on the material (LPG, water…) properties.
A conservative assumption seems reasonable: combining the energy released by both phenomena.
Uncertainty: contributions to energy released
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Not all the energy released is devoted to create overpressure, some is lost in breaking the vessel and
ejecting the fragments.
Again some uncertainty:
It is usually assumed that 50% (or 40%, less conservative) remains for overpressure.
Uncertainty: estimation of the peak overpressure
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
D. Laboureur et al., 2014:
Model with irreversible expansion (Planas et al. 2004, Casal et al., 2007) (left)
and with isentropic expansion (Prugh, 1988) (right) compared with all scales
experimental data.
Uncertainty: estimation of the peak overpressure
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
For cylindrical tanks: DP varies significantly with the direction (axial or perpendicular) in the near field.
A common method for DP: TNT equivalency
The main features of TNT explosions are well known.
If the energy involved in overpressure is converted
into the equivalent mass of TNT, the explosion peak
overpressure can be predicted from the
“scaled distance” (better in the far field).
Uncertainty: estimation of the peak overpressure
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Uncertainty: number and direction of fragments
Cylindrical tanks
Typical number of fragments: 2 or 3, depending on the heating circumstances.
An initial crack progresses along a weld (end cap); the most common possibilities:
- the tank open and flattened: no ejection, or end caps may be ejected
- tank broken in two pieces, one cap and the remainder of the vessel
- tank divided in three pieces; diverse possibilities
The most frequent one: 60% of cases
(Gubinelli and Cozzani, 2009)
Sector 1 probability: 0.62
Sector 2 probability: 0.38
Reach: can be estimated with Baum equations (maximum: 1100 m for large tanks).
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Tivissa, Spain, 2004: the initial position and the two major
fragments on a straight line.
Uncertainty: number and direction of fragments
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Uncertainty: number and direction of fragments
Zarzalico, Spain, 2011.
The three major fragments remained near the
explosion point.
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Uncertainty: number and direction of fragments
Spherical tanks
The number, direction and range is practically impossible to be predicted.
Number: 2 to 15 (usually less than 5)
Range: maximum distance reached:
600 – 700 m
México City accident
600 m
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Fireball
If the BLEVE is followed by a fireball, often the thermal effects are worse than those due to blast.
BLEVE involving a flammable material: probability of ignition (fireball) = 1
Amount of fuel: the same as for BLEVE.
Prediction of diameter and height: 23 expressions have been proposed.
When applied to 20,000 kg of propane, D ranged between 103 m and 170 m.
I propose (Martinsen and Marx, 1999; Roberts, 2000):
D (m) = 5.8 M0.333, t (s) = 0.9 M0.25 , H = 0.75 D
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Very bright flames, high E
Surface emissive power depends on the
radiant heat fraction (0.2 – 0.4).
Approximate value:
LPG: 250-350 kW m-2
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Very strong radiation, which often is much more hazardous than blast:
Chiba, Japan, 2011:
BLEVE-fireball of propane, 2000 m3 sphere, fill level 15%, P = 20 bar, failure time: 1 h,
Dfireball = 350 m, tfireball = 26 s.
Fill distance to 0.3 bar*, m fireball D, m t, s d** 100% lethality, m
0.05 72 308 23 300
0.1 75 334 25 320
0.2 82 377 28 360
0.4 92 440 33 460
0.6 100 490 37 595
0.8 107 531 40 650
Birk et al, 2013
* Total energy (l + v) ; P = 0.3 bar => lethality 100% usually accepted in risk analysis (all effects)
** This communication
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
The prediction of the risk associated to a BLEVE is subjected to diverse inevitable uncertainties:
- Frequency of occurrence: for fixed vessels can be estimated by analyzing the frequency of the
possible domino effect; for transportation can not be predicted.
- Time to failure if there is flames contact: could be predicted for pool or jet fire flames
impingement. Can not be predicted if a previous impact could have damaged the vessel or the
thermal insulation. Emergency management: assume it can be quite short.
- Amount of material involved: unknown in most cases; usually a conservative approach
(maximum amount legally possible) is applied.
- Vessel pressure: assume operating pressure if impact, or PRV set pressure if heating.
- Energy invested in overpressure wave / peak overpressure: can be estimated with models;
considering the contribution of vapor + liquid is a good approach.
- Number and direction of ejected fragments (often not considered in QRA): impossible to be
predicted with spherical vessels; can be estimated with cylindrical vessels. Reach: maximum
distances can be considered.
Conclusions
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
And for fireball (only for flammable materials):
- Frequency: that of BLEVE (assume Pignition = 1).
- amount of material involved: unknown in most cases; usually a conservative approach
(maximum amount legally possible) is applied.
Further research can reduce some of these uncertainties (for ex., energy invested in DP), but other
will remain (for ex., amount of material involved).
CENTRE FOR TECHNOLOGICAL
RISK STUDIES
Thank you very much!