ultra-high-speed label sensor · the labeling machine to stop the dispensing mechanism before the...
TRANSCRIPT
Ultra-High-Speed Label Sensor
www.ttco.com • 800-237-0946 2-123
2Specialty A
pplication Photoelectric S
ensorsH
IGH
SP
EE
D LA
BE
L•EY
E®
www.ttco.com • 800-237-09462-124
2Sp
ecia
lty A
pplic
atio
n P
hoto
elec
tric
Sen
sors
HIG
H S
PE
ED
LA
BE
L•E
YE
®
Features
• 10µs response time• 5µs repeatability• One button AUTOSET• Tweakable Up/Down adjustment• M12, M8, or cable models• Robust electrical and mechanical design• Remote AUTOSET on M12 models• Waterproof
Benefits• Easy to set up• Highly accurate and precise• Low maintenance• Affordable, low-cost option• Made in USA• Durable and reliable
Applications• Label rewinding• Label applying• Splice detection• High speed counting• Perforation detection• Weld seam detection• Registration mark sensing
Ultra-High Speed LABEL•EYE
The Ultra-High Speed LABEL•EYE is aspecial purpose slot sensor optimized to sense adhesivelabels adhering to a roll of backing paper and detectthem to within .004in of position at web speeds of 2000feet per minute. The web of labels is directed from a rollacross a peeler plate or around a sharp edge. As the webpasses around the sharp edge of the peeler plate, theadhesive label peels from the backing material. Thefunction of the sensor is to look through the backingpaper to detect the gap between the labels and signalthe labeling machine to stop the dispensing mechanismbefore the label is completely dislodged from the backingmaterial. With the next label protruding off the end ofthe peeler plate, it is now perfectly positioned to beapplied to the next product as it passes by on a conveyor.
Label Rewinding
www.ttco.com • 800-237-0946 2-125
2Specialty A
pplication Photoelectric S
ensorsH
IGH
SP
EE
D LA
BE
L•EY
E®
Features
AUTOSET
LT / DK
LOCATOR TABSHelps to center gap for proper detection
AUTOSET BUTTON1. Hold AUTOSET for 1 second when gap is
in view.2. Tap UP to increase time from threshold
(less sensitive).
LT/DK BUTTON1. Hold for one second to switch from Light
On Output to Dark On Output.2. Tap DN to decrease time to threshold
(more sensitive).
NOTE: Optimized for opaque label sensing.
CENTER of DETECTIONThis point marks the exact center of lightsource and receiver through-beam.
RED LED OUTPUT INDICATORIlluminates when output is on.Flashes when sensor is shorted oroverloaded.
GREEN LED AUTOSETFlashes rapidly during AUTOSET, for about1/2 a second, and remains illuminated whencomplete.Flashes rapidly during AUTOSET, for aboutone second, and then flashes slowly with redLED output indicator four times whenAUTOSET incomplete.
How to SpecifyExample: LER R C 10 - M12LABEL•EYE®
with Red LED
Remote AUTOSET
Connection
High Speed
M12 - Connector Type
Hardware & Accessories
GEC-66ft (1.8m)
GEC-1515ft (4.6m)
GEC-2525ft (7.62m)
RGEC-66ft (1.8m) right angle
RGEC-1515ft (4.6m) right angle
RGEC-2525ft (7.62m) right angle
4-Wire Nano Cable, M8
GEX-99ft (2.7m) extension cable
GSEC-66ft (1.8m)
GSEC-1515ft (4.6m)
GSEC-2525ft (7.62m)
GRSEC-66ft (1.8m) right angle
GRSEC-1515ft (4.6m) right angle
GRSEC-2525ft (7.6m) right angle
GX-2525ft (7.6m) extension cable
5-Wire Shielded MicroCable, M12
1. Select sensor: LABEL•EYE
2. Select remote AUTOSET:Blank = No remote AUTOSETR = Remote AUTOSET
3. Select Connection:Blank = 6ft (1.8m) cableC = 4-pin M8 connector
4. Select High Speed:Blank = standard LER10 = High Speed LABEL•EYE
5. Select M12 connector:Blank = no M12M12 = M12 pigtail connector
www.ttco.com • 800-237-09462-126
2Sp
ecia
lty A
pplic
atio
n P
hoto
elec
tric
Sen
sors
HIG
H S
PE
ED
LA
BE
L•E
YE
®
Specifications
RoHS CompliantProduct subject to change without notice
SUPPLY VOLTAGE• 10 to 30VDC• Polarity Protected
CURRENT REQUIREMENTS• 45mA (exclusive of load)
OUTPUT TRANSISTORS• (1) NPN and (1) PNP output
transistors• Sensor outputs can sink or source
up to 150mA (current limit)• All outputs are continuously short
circuit protected
RESPONSE TIME• 10µs response time• 5µs repeatability
PUSH-BUTTON CONTROL• AUTOSET - One-push button setup• LT/DK - Push and Hold to change
output Light On/Dark On• UP/DWN - Tweak-able Up/Down
Adjustment
LED LIGHT SOURCE• High intensity red LED• Pulse modulated
HYSTERESIS• Minimal hysteresis promotes the
detection between the backingmaterial and the label depending onthe settings
LIGHT IMMUNITY• Responds to sensor’s pulsed
modulated light source, resulting inhigh immunity to most ambientlight
INDICATORS• Green LED flashes when AUTOSET
routine is activated and staysilluminated when AUTOSET iscompleted
• Red LED illuminates when sensor’soutput transistors are ON.
AMBIENT TEMPERATURE• -40°C to 70°C (-40°F to 158°F)
RUGGED CONSTRUCTION• Chemical resistant high
thermoplastic PPS housing• Waterproof, ratings: NEMA 4 and
IP66• Conforms to heavy industry grade
CE and UL requirements
B row n* (1)R ed
G reenB lack* (4)
W hiteW hite * (2)
B lue* (3)B lack
LO A D
LO A D
B lueG ray* (5)
P os
N P N(S ink)
P N P(S ource)
N eg
R em oteA utoset
30 V D C10 To
Label Eye Wiring (Remote Set)
B row n* (1)R ed
G reenB lack* (4)
W hiteW hite * (2)
B lue* (3)B lack
LO A D
LO A D
P os
N P N(S ink)
P N P(S ource)
N eg
30 V D C10 To
Label Eye Wiring (Standard)
* - S enso rs w ith connectors
1 - P os itive2 - N P N3 - N egative4 - P N P5 - R em ote A utoset(P in 5 no t present onnon-R em ote m ode ls)
M 12 M ale C onnector
2
3
1
4
5
M 8 M ale C onnector
1 - P os itive2 - N P N3 - N egative4 - P N P
4
3
2
1
* - S enso rs w ith connectors
M 8 R E A R V IE W
C A B LE / M 12 R E A R V IE W
0.47
2" [1
2.0m
m]
1.07
1" [2
7.2m
m]
0.70
9" [1
8.0m
m]
0 .709" [18.0m m ]
2 .116" [53.8m m ]
0.11
7" [3
.0m
m]
0.92
6" [2
3.5m
m]
0 .630" [16 .00m m ]
2 .520" [64 .00m m ]
2X 6 -32 X 1 /4 " D E E PM O U N T IN G H O LE S
2X Ø 0.167" [Ø 4 .25m m ]
1.07
3" [2
7.3m
m]
3 .686" [93 .63m m ]
6 FT S H IE LD E DC A B LE
6" M 12 P IG TA ILC O N N E C TO R
Connections and Dimensions Ultra-High Speed LABEL•EYE