u-style stand diving system assembly & installation ... · diving boards that are improperly...

U-STAND-IM Rev. 3/09 (BK-USTAND BOOK)

U-STYLE STAND DIVING SYSTEMAssembly & Installation Instructions

3 0 5 0 S . A L V E R N O N W A Y • T U C S O N , A Z 8 5 7 1 35 2 0 . 7 9 0 . 7 0 4 0 • 8 0 0 . 7 3 7 . 5 3 8 6 • F A X 5 2 0 . 7 9 0 . 7 1 2 7

i n t e r - f a b . c o m

ATTENTION

INSTALLERS:

Please deliver and

review this manual with

HOMEOWNER.


3 0 5 0 S . A L V E R N O N W A Y • T U C S O N , A Z 8 5 7 1 35 2 0 . 7 9 0 . 7 0 4 0 • 8 0 0 . 7 3 7 . 5 3 8 6 • F A X 5 2 0 . 7 9 0 . 7 1 2 7

i n t e r - f a b . c o m

U-STYLE STAND DIVING SYSTEMOWNER’S MANUAL

ATTENTION

INSTALLERS:

Please deliver and

review this manual with

HOMEOWNER.

For Technical Support or Assistance, Contact Customer Service at:

INTER-FAB, INC.3050 S. ALVERNON WAY

TUCSON, AZ 85713(800) 737-5386

or visit: www.inter-fab.com

To obtain complete copies of the most currentANSI/NSPI 2003 Standards for Inground Pools or to obtain copies of the “Plan Your Dive, Steer Up”

or “The Sensible Way to Enjoy Your IngroundSwimming Pool” contact:

The Association of Pool & Spa Professionals(APSP)

2111 Eisenhower Ave.Alexandria, VA 22314

(703) 838-0083

or visit: www.theapsp.org


I N S T A L L A T I O N M A N U A L U - S T A N D ™

1U-STAND-IM Rev. 3/09 (BK-USTAND BOOK)

TABLE OF CONTENTS:

Safety First .........................................................................2-3

Important Notices to the Installer..............................................4

Board to Base Compatibility Chart.............................................4

RESIDENTIAL:

Minimum Diving Water Envelope Information...............................5

U-Stand Base Placement - Residential........................................6

U-Stand Specifications - Residential ...........................................6

Exploded View Diagram............................................................7

Installation Instructions - Residential ..........................................8

Article 5 Extracted from ANSI/NSPI-5 2003.........................9-14

COMMERCIAL:

U-Stand Base Placement - Commercial ....................................15

U-Stand Specifications - Commercial ........................................15

Public Board Mounting Diagram..............................................16

Installation Instructions - Commercial.......................................16

Article 5 Extracted from ANSI/NSPI-1 2003.......................17-25

Inter-Fab Limited Warranty.....................................................26



This Inter-Fab diving board and/or stand shall be installed only by a professional swimming poolcontractor or with the direct supervision of a licensed professional, engineer or architect. Divingboards may be installed only on residential or public inground swimming pools properly designedfor their use. Diving boards that are improperly installed can be very dangerous to the user resultingin possible serious head and/or spinal column injury, including the paralysis or death of the user.

It is very important that this diving board and/or stand be installed only on residential ingroundpools which meet or exceed the minimum water envelope dimensions of the American NationalStandard for Residential Inground Swimming Pools [ANSI/NSPI-5 2003) or on public ingroundpools that meet or exceed the minimum water envelop dimensions of the ANSI/NSPI-1 2003 standardfor public pools and in accordance with the included INTER-FAB POOL SPECIFICATIONS. Installationshould conform to local building regulations if they exceed the ANSI/NSPI standards.

In addition to the above standards and referenced specifications, these installation instructionsprovided by Inter-Fab, Inc. must be followed diligently.

It is also important that any and all warnings provided with the diving board be strictly adhered toand posted in a conspicuous location. If not provided or they are misplaced, please purchase warningsigns from your pool contractor or professional pool supply store and post them in a location thatthe users of the diving board can clearly see.

“A pool is the safest place to swim and a diving board installed in compliance with manufacturersinstructions and the ANSI/NSPI-5 2003 standards for residential inground swimming pools andthe ANSI/NSPI-1 2003 standards for public inground swimming pools is the safest place to divefrom. To ensure that you are able to safely enjoy your diving board for many years, it is critical thatyou follow the following instructions.”

SAFETY FIRST!

DIVING TIPS: Even the safest equipment must be used properly. Inter-Fab promotes safe diving byoffering these tips on the proper use of your diving board: always dive into water that meets depthrequirements, with arms extended; be aware of the bottom and the walls of the pool; avoid collisionswith pool toys and floats; and instruct your pool users to always “steer up”. When you begin yourdive you must get ready to steer up. As you enter the water, your arms must be extended overyour head, hands flat aiming up. Hold your head and arch your back.

ONLY ONE PERSON ON THE DIVING BOARD AT ONE TIMEMAXIMUM WEIGHT = 250 LBS

Plan Your Dive

Back Arched

Arms Extended

Head and Hands Up

Hold Diving Form

Steer up for a safe dive.

PLAN YOUR DIVE, STEER UP



A pool is the safest place to swim and a diving board installed in compliance with manufacturersinstructions and the ANSI/NSPI-5 2003 standards for residential inground swimming pools andthe ANSI/NSPI-1 2003 standards for public inground swimming pools is the safest place to divefrom. To ensure that you are able to safely enjoy your diving board for many years, it is critical thatyou follow the following instructions.

SAFETY FIRST!

DO1. Know the shape and depth of the pool before

you dive.

2. Make sure that all family members and guestsare familiar with these instructions before theyuse your pool and diving board.

3. Make sure that the diving board has beeninstalled in compliance with the Assembly andInstallation Instructions and with the 2003ANSI/NSPI Standards for In-ground Pools.This includes the shape and depth of the poolas well as the height of the diving board.

4. Enter feet first the first time.

5. Plan your path to be sure you avoid any otherswimmers, or objects in or under the water,such as floats, tires, toys etc.

6. Keep your head up, arms up and fully extendedand steer up with your hands.

7. Practice carefully before you dive headfirst.

8. Become familiar with the diving board and itsspring before diving headfirst

9. Dive straight ahead, not to the side of theboard or pool.

10. Dive from the diving board only.

11. Make sure that children and non-swimmersare supervised at all times.

12. Always remember that when you dive you muststeer up.

13. Inspect your diving board, base and stand ona regular basis (at least twice a year) and keepthem in proper repair.

14. Contact your dealer, installer or Inter Fab(800-737-5386) with any questions or concernsabout the safe use of your diving board.

DON’T1. Don’t drink and dive.

2. Don’t install this or any diving board on anabove ground pool or dive into an aboveground pool from any surface.

3. Don’t dive into a pool from anyplace not specif-ically designated for diving. Never dive into theshallow portion of any pool.

4. Don’t dive across the width of the pool or tothe sides of the pool.

5. Don’t Run and dive.

6. Don’t engage in horseplay in or around the divingboard or pool.

7. Don’t use your diving board as a trampoline.

8. Don’t do a back dive. Backyard pools are notbuilt for that type of activity.

9. Don’t try fancy dives. Keep the dives simple.

10. Don’t dive into or through objects or toys suchas inner tubes.

11. Don’t swim or dive alone.

12. Don’t use a diving board or stand or base thatis rusted or worn out or in poor repair.

THE U-STAND DIVING SYSTEM IS A DIVING BOARD



The specifications found in this manual represent the minimum water envelope required by Inter-faband by the ANSI/NSPI 2003 Standards for Inground Swimming Pools. Each of these dimensionsmust be met or exceeded. Installation of a diving board of any type on a pool that does not meetor exceed each of the minimum specifications as provided in this manual including but not limitedto the slope requirement, is in direct violation of this manufacturer’s instructions and the 2003Standards, and can result in serious injury or death.

A 6’ diving board can only be installed on a 12” or 18” U-Stand base; an 8’ diving board can onlybe installed on a 12” or 18” U-Stand base; a 10’ diving board can only be installed on an 18” or24” U-Stand base; and a 12’ diving board can only be installed on a 24” U-Stand base.

Comply with local government regulations for Inground Swimming Pools if they exceed theANSI/NSPI 2003 Standards.

Read carefully pages 9-14 and pages 17-25 of this installation manual which contain portions ofthe ANSI/NSPI-5 2003 Standard for Residential Inground Swimming Pools, and the ANSI/NSPI-12003 Standard for Public Swimming Pools.

NOTE: The installation of this diving board and/or stand is not complete until you, the installerhave measured the pool as well as the diving board’s height above water and the board’s overhangto ensure they meet Inter-Fab’s minimum water envelope specifications and the ANSI/NSPI 2003Standards For Inground Swimming Pools. In addition, the installation of this diving board and/orstand is not complete until you the installer have delivered to your customer and reviewed with yourcustomer the “Owners Manual” as well as the “Plan Your Dive Steer-Up” brochure.

IMPORTANT NOTICES TO THE INSTALLER

ONLY ONE PERSON AT A TIME ON THE DIVING BOARD,WITH A MAXIMUM WEIGHT LIMIT OF 250 LBS.

BASE TYPE 6’ 8’ 10’ 6’ 8’ 6’ 8’ 10’ 12’ 6’ 8’ 6’ 8’ 10’ 10’ 12’ 14’ 16’U-Stand 12” S S – – – U1 U1 – – – – U2 U2 – – – – –

U-Stand 18” S S S – – U1 U1 U1 – – – U2 U2 U2 U3 – – –

U-Stand 24” – – S – – – – U1 U1 – – – – U2 U3 U3 – –

DURO-BEAM DURO-SPRING TECHNI-BEAM BAJA OLYMPIAN COMMERCIAL

** NOTE: The Chart above refers to standard wood core diving boards and standard fiberglass and steel diving bases.

CHART KEY: S = STANDARD; U1 = UPGRADE 1; U2 = UPGRADE 2; U3 = UPGRADE 3; – = NOT AVAILABLE

INTER-FAB BOARD TO BASE COMPATIBILITY CHART **



MINIMUM DIVING WATER ENVELOPE:NOTE: DRAWINGS ARE NOT TO SCALE.

NOTES:

DIVING EQUIPMENT

TIP OF BOARDABOVE POINT A

D I V I N G E Q U I P M E N T P R O H I B I T E D

D I V I N G E Q U I P M E N T P R O H I B I T E DA B C D A B C D WA+/-3” AB BC CD* DE WE

0

I 6’-0” 7’-6” 5’-0” 2’-9” 10’-0” 12’-0” 10’-0” 8’-0” 1’-6” 7’-0” 7’-6” VARIES 6’-0” 28’-9”

II 6’-0” 7’-6” 5’-0” 2’-9” 12’-0” 15’-0” 12’-0” 8’-0” 1’-6” 7’-0” 7’-6” VARIES 6’-0” 28’-9”

III 6’-10” 8’-0” 5’-0” 2’-9” 12’-0” 15’-0” 12’-0” 8’-0” 2’-0” 7’-6” 9’-0” VARIES 6’-0” 31’-3”

IV 7’-8” 8’-6” 5’-0” 2’-9” 15’-0” 18’-0” 15’-0” 9’-0” 2’-6” 8’-0” 10’-6” VARIES 6’-0” 33’-9”

V 8’-6” 9’-0” 5’-0” 2’-9” 15’-0” 18’-0” 15’-0” 9’-0” 3’-0” 9’-0” 12’-0” VARIES 6’-0” 36’-9”

POOLTYPE

MINIMUM DEPTHS AT POINT

MINIMUM WIDTHS AT POINT

MINIMUM LENGTHS BETWEEN POINTS

TABLE 1 - MINIMUM WATER ENVELOPE (ANSI/NSPI-5 2003)

DBL** HOW** F G H J K L M N

0

I 6’ DB/6’ JB 20” 2’-9” 5’-0” 4’-0” 7’-2.5” 7’-6” 6’-0” 3’-9” 2’-1.5” 12’

II 8’ DB/6’ JB 20” 2’-9” 3’-10” 4’-2” 7’-2.5” 7’-6” 6’-8” 3’-9” 2’-1.5” 12’

III 10’ DB/8’ JB 26” 2’-9” 4’-4.75” 4’-4.5” 7’-5.5” 8’-0” 6’-7” 3’-11.5” 1’-7.5” 13’

IV 10’ DB/8’ JB 30” 2’-9” 5’-10.5” 3’-10” 7’-8” 8’-6” 8’-3” 5’-7” 2’-7” 13’

V 12’ DB/8’ JB 40” 2’-9” 6’-2” 3’-11.5” 7’-9.5” 9’-0” 8’-2.5” 5’-9” 2’-7” 14’

POOLTYPE

MAX. DIVINGBOARDLENGTH

MAX. HEIGHTOVER WATERAT POINT A

CROSS SECTIONALDIMENSIONS AT

POINT A CROSS SECTIONAL DIMENSIONS AT POINT B

TABLE 2 - INTER-FAB RESIDENTIAL POOL MINIMUM SPECIFICATIONSMIN. HEAD

ROOMABOVE DIVING

SURFACES

*Min. length between points CD may vary based upon water depth at point D and the slope between points C & DABBREVIATIONS: **DBL=Diving Board Length; DB=Diving Board; JB=Jump Board; **HOW=Height Over Water

F

G

H

J K

NM

LDIVING EQUIPMENT

RESIDENTIAL INGROUND POOL INSTALLATION



TABLE 5 – RESIDENTIAL PLACEMENT CHARTADDITIONALLY REFER TO: ANSI/NSPI-5 2003 American National Standard for Residential IngroundSwimming Pools and to page 5 for Inter-Fab Residential Inground Pool Minimum Specifications.

* IMPORTANT: The distance for setting the front jig bolt (S) from the water’s edge is valid only if the minimum water depth is maintained at the tip of the board noted aspoint “A” in ANSI/NSPI-5 2003 American National Standard for Residential Inground Swimming Pools. If minimum water depth is not maintained the distance (S) mustbe adjusted accordingly.** “WA” dimension is valid only in conjunction with the minimum depth at point “A” for type pool in accordance with ANSI/NSPI-5 2003 American National Standardfor Residential Inground Swimming Pools.

NOTE: READ THESE INSTRUCTIONS IN THEIR ENTIRETY BEFORE ATTEMPTING THE INSTALLATION.

FIG. A – U-STAND RESIDENTIALPLACEMENT SPECIFICATIONS:

INTER-FAB CANNOT GUARANTEE CUSTOMER’SCONCRETE OR THICKNESS

NOTE: WHEN COPING IS USED, DO NOT SET FRONT U-STANDCLOSER THAN 3” FROM THE BACK EDGE OF THE COPING.

IMPORTANT:THESE DIMENSIONS

ARE ACCURATE ONLY

FOR VERTICAL POOL

WALLS, TYPICALLY

GUNITE CONSTRUC-

TION, WITH LESS

THAN A 3’ RADIUS TO

THE POOL FLOOR.

DUE TO THE VARYING

SIZES OF OTHER

POOLS, TYPICALLY

VINYL LINER CON-

STRUCTION, PLEASE

CONTACT CUSTOMER

SERVICE FOR PROPER

PLACEMENT.

1-800-737-5386

U-STANDARDSPART #

(Note: there are several sizesavailable for each pool type)

NOMINALBOARDLENGTH

ANSI/NSPI-5POOL TYPE

DISTANCE FROM WATER’S EDGE TO FORWARD

U-STAND(S)

DISTANCE FROM END OF BOARD

TO FORWARD U-STAND

MAX HEIGHTOF BOARD

ABOVE WATER(HOW)

DBU12049 6’ I 18.25” 36.25” 18” 20”DBU12049 6’ II 18.25” 36.25” 18” 20”

DBU12049 or DBU18049 6’ III 12.25” 36.25” 24” 26”DBU12049 or DBU18049 6’ IV 6.25” 36.25” 30” 30”DBU12049 or DBU18049 6’ V

8’ IDBU12049 8’ II 32” 50” 18” 20”

DBU12049 or DBU18049 8’ III 26” 50” 24” 26”DBU12049 or DBU18049 8’ IV 20” 50” 30” 30”DBU12049 or DBU18049 8’ V 14” 50” 36” 40”

10’ I10’ II

DBU18049 or DBU24049 10’ III 37.5” 61.5” 24” 26”DBU18049 or DBU24049 10’ IV 31.5” 61.5” 30” 30”DBU18049 or DBU24049 10’ V 25.5” 61.5” 36” 40”

12’ I12’ II12’ III12’ IV

DBU24 12’ V 40” 76” 36” 40”

MIN.OVERHANGPLUS OR

MINUS 3”(WA)

Not recommended. Call customer service for more information.NOT ALLOWED

NOT ALLOWEDNOT ALLOWED

NOT ALLOWEDNOT ALLOWEDNOT ALLOWEDNOT ALLOWED


A B C6’ 12”, 18” 30” ±3”8’ 12”, 18” 40” ±4”10’ 18”, 20” 52” ±5”12’ 20” 62” ±6”

MODEL SIZE OD WALLDBU12049 12” 1.90” .049”DBU18049 18” 1.90” .049”DBU18065 18” 1.90” .065”DBU24065 20” 1.90” .065”

IMPORTANT NOTICE: WHEN PROPERLY INSTALLED, INTER-FAB’S 12” AND 18” U-STANDS WILL HAVE 4” OF THE RAIL EMBEDDED WITHIN THE DECK AND WILL MEASURE (RESPECTIVELY) 12” OR 18” FROM THE TOP OF THE RAIL TO THE SURFACEOF THE DECK. THE 24” U-STAND IS DIFFERENT, WHEN PROPERLY INSTALLED 4” OFTHE RAIL WILL BE EMBEDDED WITHIN THE DECK AND IT WILL MEASURE 20” FROMTHE TOP OF THE RAIL TO THE SURFACE OF THE DECK.

TABLE 3 – U-STAND SPECS TABLE 4 – U-STAND MATERIALWA



TIGHTENING SCHEDULE:Secure Board to Stand withMounting Hex Nuts at 20-25FT-LBS

FIG. B – U-STAND BASE EXPLODED VIEW


DRAWING REPRESENTS THE FOLLOWING PART NUMBERS:DBU12049 (shown)

DBU18049DBU18065DBU24049DBU24065

ITEM # COMPONENT DESCRIPTION DB-M

N/A

KITS – QTY.

1 DBU12049 12" U Style Diving Standards 2

2 DB6WW 6' Duro-Beam White w/White Top Tread & Hdw Kit 1

3 FC Fulcrum Cover For U-Standard Base 1

4 H-WHT WAS/CAP I.F. White Washer/Cap 2

5 H-SS 5 C BOLT 1/2-13 x 5 Carriage Bolt S.S. 2

6 H-1/2 BLK WASH 1/2 x 2" Black Rubber Washer 2

7 H-1/2 RED WASH 1/2 x 2" Red Rubber Washer 2

8 H-SS 1/2 F WAS 1/2 USS Flat Washer S.S. 2

9 H-SS 1/2 LOC WA 1/2 Lock Washer S.S. 2

10 H-SS 1/2 H NUT 1/2"- 13 Hex Finish Nut S.S. 2

11 H-1-1/2 WHT CAP .750 x 1-1/2 White UV Nut Cap 2

NOTES:DB6WW diving board shown in exploded view for illustration purposes. Must be purchased separately. Other diving board options available.

TABLE 6 – PARTS LIST

NO. 3 Rebar(Not Included)

HARDWARE NOTE:Use a small dab of anti seizelubricant (included) on all boltthreads.



U-Stand Diving BaseRESIDENTIAL POOL INSTALLATION INSTRUCTIONS

Be sure the concrete deck surrounding the U-Stands complies with the minimum dimensions asshown in Figure A on page 6.

Read and understand the ANSI/NSPI-5 2003 American National Standard for Residential Ingroundswimming Pools and Table 1 and Table 2 on page 5 before you install the U-Stand Diving System.

The U-Stands should be set in accordance with Figure A and Table 3 on page 6. The diving boardmust be placed on the deep end of the pool on centerline.

Make sure the U-Stands are set 4” into the concrete with ample concrete depth below the stand inaccordance with Figure A on page 6. Do not install the U-Stand Diving System if the deck does notmeet the minimum requirements.

When finishing the deck surface, maintain a level deck where the U-Stands project out of the decksurface. Both U-Stands must be leveled left to right and to each other when installing. This will allowthe diving board to sit level left to right and have a slight upward pitch at the toe end once the rubberfulcrum pad is in place. Allow the cement to fully cure before bolting the diving board to the U-Stands.

When mounting diving board to a newly installed stand with a permanently fixed fulcrum, the correctmeasurement between the mounting holes and the fulcrum must be maintained so as not to voidthe warranty. See Figure A and Table 3 on page 6.

The rubber fulcrum pad MUST be used so as not to void the Inter-Fab warranty.

The top surface of the diving board from the deck end tothe tip end shall be level or have an upward slope of 5/8"per foot maximum. Elevation difference shall not exceed6" from the deck end to the tip of the board. There shallbe no downward slope towards the water. The slope shallbe measured using a level as shown in the graphic to theleft.

ONLY ONE PERSON ON THE DIVING BOARD AT A TIME, WITH A MAXIMUM WEIGHTOF 250 LBS.


The Diving Board must be installed according the below board leveling instructions:



SUPPORT INFORMATION: ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES Extracted from ANSI/NSPI- 2003, American National Standard for Residential Inground Swimming Pools




To obtain complete copies of the ANSI/NSPI-5 2003 Standard for Residential Inground Pools contact:

The Association of Pool & Spa Professionals (APSP)2111 Eisenhower Ave.Alexandria, VA 22314

(703) 838-0083

or visit: www.theapsp.org



TABLE 8 – INTER-FAB PUBLIC POOL SPECIFICATIONS

POOL TYPE

VI 10’ (2/3 Meter)26”

VII 12’ (3/4 Meter)30”

VIII 16’ 1 Meter

IX 16’ 3 Meter

RELATED DIVING EQUIPMENT

MAX. DIVINGBOARDLENGTH

MAX. BOARDHEIGHT

OVER WATER

Placement of boards shall observe the following minimum dimensions.With multiple board installations, minimum pool widths must be

increased accordingly.

• Deck Level Board to Pool Side 8’• 1 Meter Board to Pool Side 10’• 3 Meter Board to Pool Side 11’• 1 Meter or Deck Level Board to 3 Meter Board 10’• 1 Meter or Deck Level Board to Another

1 Meter or Deck Level Board 8’• 3 Meter to Another 3 Meter Board 10’

PUBLIC POOL INSTALLATIONNOTE: READ THESE INSTRUCTIONS IN THEIR ENTIRETY BEFORE ATTEMPTING THE INSTALLATION.

INTER-FAB CANNOT GUARANTEE CUSTOMER’SCONCRETE OR THICKNESS

NOTE: WHEN COPING IS USED, DO NOT SET FRONT U-STANDCLOSER THAN 3” FROM THE BACK EDGE OF THE COPING.

TABLE 7 – U-STAND MATERIAL

FIG. C – U-STAND COMMERCIALPLACEMENT SPECIFICATIONS:

MATERIALS: 1.90” OD, .065” WALL, 304STAINLESS STEEL.NOTE: ONLY .065” U-STANDS CAN BEINSTALLED ON A PUBLIC POOL.

MODEL SIZE OD WALL

DBU18065 18” 1.90” .065”

DBU24065 24” 1.90” .065”

TABLE 9 – COMMERCIAL PLACEMENT CHARTADDITIONALLY REFER TO: ANSI/NSPI-1 2003 American National Standard for Public Swimming Pools.

* IMPORTANT: The distance for setting the front jig bolt (S) from the water’s edge is valid only if the minimum water depth is maintained at the tip of the board noted aspoint “A” in ANSI/NSPI-1 2003 American National Standard for Public Inground Swimming Pools. If minimum water depth is not maintained the distance (S) must beadjusted accordingly.** L1 dimension is valid only in conjunction with the minimum depth at point “A” for type pool in accordance with ANSI/NSPI-1 2003 American National Standard forPublic Inground Swimming Pools.

U-STANDARDSPART #

NOMINALBOARDLENGTH

(A)

ANSI/NSPI-5POOL TYPE

DISTANCE FROM WATER’S EDGE TO FORWARD

U-STAND(S)

DISTANCE FROM END OF BOARD

TO FORWARD U-STAND

MAX HEIGHTOF BOARD

ABOVE WATER(HOW)

HEIGHT OF U-STAND

(B)

FULCRUMSETTING

(C)

DBU18065 or DBU24065 10’ VI 31.5” 61.5” 30” 26” 18”, 20” 52” ± 5”DBU18065 or DBU24065 10’ VII 25.5” 61.5” 36” 30” 18”, 20” 52” ± 5”

DBU24065 12’ VII 40” 76” 36” 30” 20” 62” ± 6”

MIN.OVERHANG

(L1)

IMPORTANT: THESE DIMENSIONS ARE ACCURATE ONLY FOR VERTICAL POOL WALLS, TYPICALLY GUNITE

CONSTRUCTION. PLEASE CONTACT CUSTOMER SERVICE FOR PROPER PLACEMENT. 1-800-737-5386

IMPORTANT NOTICE: WHEN PROPERLY INSTALLED, INTER-FAB’S 18” U-STAND WILLHAVE 4” OF THE RAIL EMBEDDED WITHIN THE DECK AND WILL MEASURE 18” FROMTHE TOP OF THE RAIL TO THE SURFACE OF THE DECK. THE 24” U-STAND IS DIFFERENT,WHEN PROPERLY INSTALLED 4” OF THE RAIL WILL BE EMBEDDED WITHIN THE DECKAND IT WILL MEASURE 20” FROM THE TOP OF THE RAIL TO THE SURFACE OF THE DECK.

PUBLIC POOL INSTALLATION



FIG. D – PUBLIC POOL BOARD MOUNTING DIAGRAM

NOTE: Tighten Hex Nuts Between 20-25 FT/LBS. DO NOT OVER TIGHTEN.

1

23

3

4 5

67

Mounting KitDiving Board

U-Stand

COMMERCIAL MOUNTING KIT KEY:1. 1/2” X 6” Carriage Bolt Stainless Steel (2 ea.)2. Stainless Steel Top Mounting Plate (1 ea.)3. Rubber Mounting Pad (2 ea.)4. Bottom Mounting Plate (1 ea.)5. 1/2” Lock Washer C/S Stainless Steel (2 ea.)6. 1/2” Hex Nut C/S Stainless Steel (2 ea.)7. 1/2” White Rubber Bolt Cap (2 ea.)

HARDWARE NOTE:Use a small dab ofanti seize lubricant(included) on all boltthreads.

12”

4”

U-STAND DIVING BASE PUBLIC POOL INSTALLATION INSTRUCTIONSBe sure the concrete deck surrounding the U-Stands complies with the minimum dimensions asshown in Figure C on page 15.

Read and understand the ANSI/NSPI-1 2003 American National Standard for Public SwimmingPools and Table 8 and Table 9 on page 15 before you install the U-Stand Diving System.

The U-Stands should be set in accordance with Figure C and Table 8 and 9 on page 15. The divingboard must be placed on the deep end of the pool on centerline.

Make sure the U-Stands are set 4” into the concrete with ample concrete depth below the stand inaccordance with Figure C on page 15. Do not install the U-Stand Diving System if the deck doesnot meet the minimum requirements.

When finishing the deck surface, maintain a level deck where the U-Stands project out of the decksurface. Both U-Stands must be leveled left to right and to each other when installing. This will allowthe diving board to sit level left to right and have a slight upward pitch at the toe end once th rubberfulcrum pad is in place. Allow the cement to fully cure before bolting the diving board to the U-Stands.

When mounting diving board to a newly installed stand with a permanently fixed fulcrum, the correctmeasurement between the mounting holes and the fulcrum must be maintained so as not to voidthe warranty. See Figure C and Table 8 and 9 on page 15.

The rubber fulcrum pad MUST be used so as not to void the Inter-Fab warranty.

A rubber mounting pad MUST be installed between the bottom of the diving board and the heel endU-Stand as not to void the Inter-Fab warranty.

The top surface of the diving board from the deck end tothe tip end shall be level or have an upward slope of 5/8"per foot maximum. Elevation difference shall not exceed6" from the deck end to the tip of the board. There shallbe no downward slope towards the water. The slope shallbe measured using a level as shown in the graphic to theleft.

The Diving Board must be installed according the below board leveling instructions:



SUPPORT INFORMATION: ARTICLES 1–7 Extracted from ANSI/NSPI-1 2003, American National Standard for Public Swimming Pools



SUPPORT INFORMATION: ARTICLE 23.1.5 Extracted from ANSI/NSPI-1 2003, American National Standard for Public Swimming Pools

To obtain complete copies of theANSI/NSPI-1 2003 Standard forPublic Swimming Pools contact:

The Association of Pool & SpaProfessionals (APSP)

2111 Eisenhower Ave.Alexandria, VA 22314

(703) 838-0083

or visit: www.apsp.org



LIMITED WARRANTYInter-Fab, Inc. will repair or replace, at its option, any product manufactured by Inter-Fab, Inc. that fails duringthe applicable warranty period because of a manufacturing or material defect; provided that the defect is notthe result of improper installation, improper use or care, negligence, alterations or modifications to the product,or natural accidents (acts of God). The applicable warranty period for products manufactured by Inter-Fab,Inc. is three (3) years from the date of retail purchase, except as specified below:

Echoes of Nature™ products are individually handcrafted and painted by skilled artisans and as a result,dimensional differences and color variations are normal and are not a basis for warranty coverage. The warrantyperiod for pumps sold with the Echoes of Nature™ products is three (3) years from the date of retail purchase.

Water Sports™ sports equipment warranty periods are as follows: Volleyball Poles, Basketball Poles,Basketball Rim, and Basketball Backboard are one (1) year from date of retail purchase. Volleyball, VolleyballNet, Basketball, Basketball Net, and pumps are warranted for ninety (90) days from date of retail purchase.

Splash Rock™ Edgewater, T7™ Edgewater™ and Lighted Edgewater™ features warranty period is one (1) yearfrom date of retail purchase.

Zoomerang™ slide products warranty period is one (1) year from the date of retail purchase.

Build Your Own Slide™ (BYOS™) warranty period is one (1) year from the date of retail purchase.

City 2™ Slide and City Base™ products warranty period are one (1) year from the date of retail purchase.

Unless expressly stated otherwise all products manufactured by Inter-Fab are for residential installation (singlefamily residence) inground pool use only. Inter-Fab, Inc. expressly disclaims any and all warranties and liabilityarising from the installation or use of its residential products for any non-residential use such as semi-public,public, or commercial applications. Products expressly manufactured for commercial installation and use will besubject to this limited warranty.

This limited warranty is in lieu of all other warranties, whether express or implied. Inter-Fab, Inc. disclaimsany warranty of merchantability or fitness for a particular use, and noninfringement in relation to any of its productsand Inter-Fab, Inc. is not liable for consequential, incidental or specific damages. This warranty is limited tothe repair or replacement of the manufacturing or material defect, or refund of the original purchase price,whichever is less, at the sole option of Inter-Fab, Inc., and expressly does not cover any labor or reinstallationexpenses related to the replacement of any and all Inter-Fab products. This limited warranty shall be the soleand exclusive remedy of irrespective of whether the claims are made in contract, tort, warranty, law, equityor by statue.

This warranty is to the original purchaser of the product only. Inter-Fab’s limited warranty is neither transferablenor portable from consumer to consumer. The effective coverage date begins at the date of retail purchase.Product owner or representative must notify Inter-Fab, Inc. (or its wholesale agent) in writing, giving a fulldescription of the nature of the product defect or failure along with proof of purchase, serial number(s) of theproduct and photos within thirty (30) days of the expiration of the applicable warranty period. Inter-Fab, Inc.reserves the right to physically inspect damaged or defective products or components to determine the causeof the damage or defect, prior to authorizing repair or replacement of its products.

3050 S. Alvernon Way • Tucson, AZ 85713520.790.7040 • 800.737.5386 • Fax 520.790.7127 • inter-fab.com

u-style stand diving system assembly & installation ... · diving boards that are improperly...

Documents