tzidc-200_18348

8/12/2019 TZIDC-200_18348

1/24

Data Sheet10/18-0.32-EN

Electro-Pneumatic PositionerTZIDC-200

Pos: 1/Titelbltter / Copyright/DB/Aktorik/Stellungsregler/Elektropneumatischer Stellungsregler TZIDC-200@8\mod_1176719585890_3101.doc @82998

for 4 20 mA two-wire technology,

flameproof enclosure

Low operating cost

Compact design

Well-proven technology and intelligence

Robust and environmentally ruggedized

Wide operating temperature range-40 ... 85 C (-40 ... 185 F)

Easy to commission, single pushbuttonoperating philosophy

Mechanical position indicator

ATEX, FM, CSA, GOST and IECEx approvals

- flameproof enclosure-intrinsically safe

For SIL2 safety loops

Compact, well-proven, and flexible

Pos: 2/Inhaltsverzeichnis/Inhaltsverzeichnisfr alleDokumente@0\mod_1138710310890_3101.doc @3129Contents

8/12/2019 TZIDC-200_18348

2/24

Electro-Pneumatic Positioner TZIDC-200 10/18-0.32-ENfor 4 20 mA two-wire technology, flameproof enclosure

2

Contents

1 Description...........................................................................................................................................................3

1.1 Pneumatics.....................................................................................................................................................3

1.2 Operation........................................................................................................................................................3

1.3 Communication ..............................................................................................................................................3

1.4 Inputs and outputs..........................................................................................................................................3

1.5 Modular design...............................................................................................................................................3

2 Mounting versions...............................................................................................................................................5

2.1 To linear actuators in accordance with the standard .....................................................................................5

2.2 To rotary actuators in accordance with the standard .....................................................................................5

2.3 Integral mounting to control valves ................................................................................................................5

2.4 Special actuator-specific mounting ................................................................................................................5

3 Operation..............................................................................................................................................................7

3.1 General...........................................................................................................................................................7

3.2

Operator panel ...............................................................................................................................................8

4 Communication ...................................................................................................................................................9

4.1 DTM................................................................................................................................................................9

4.2 LKS adapter (RS-232 interface converter).....................................................................................................9

4.3 FSK Modem ...................................................................................................................................................9

5 Technical data....................................................................................................................................................10

5.1 Input..............................................................................................................................................................10

5.2 Output...........................................................................................................................................................10

5.3 Travel............................................................................................................................................................10

5.4 Air supply......................................................................................................................................................10

5.5 Transmission data and influences................................................................................................................10

5.6 Environmental capabilities ...........................................................................................................................11

5.7 Housing ........................................................................................................................................................11

5.8 Safety Integrity Level....................................................................................................................................11

5.9 Explosion protection.....................................................................................................................................12

5.10 Options.........................................................................................................................................................12

5.11 Accessories..................................................................................................................................................13

6

Electrical connection ........................................................................................................................................14

7 Dimensions........................................................................................................................................................16

8 Ordering information.........................................................................................................................................19

8.1 Ordering information (continued) .................................................................................................................20

8.2 Additional ordering information ....................................................................................................................20

8.3 Order information, accessories 1 .................................................................................................................21



8/12/2019 TZIDC-200_18348

3/24


3

Pos: 3.1/berschriften/1/G- L/Kurzbeschreibung@7\mod_1175676881796_3101.doc @75993

1 DescriptionPos: 3.2/==== Wechselein- auf zweispaltig==== @0\mod_1130421847171_3101.doc @3828Wechselein-auf zweispaltigPos: 3.3/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Kurzbeschreibung/KurzbeschreibungTZIDC-2x0@10\mod_1176706470984_3101.doc @81985

The TZIDC-200 is an electronically configurable positioner withcommunication capabilities, mounting to pneumatic linear or rotaryactuators. It features a small and compact design, a modularconstruction, and an excellent cost-performance ratio.

Fully automatic determination of the control parameters andadaptation to the final control element yield considerable time savingsand an optimal control behavior.

Pos: 3.4/berschriften/1.1/2-spaltig/Pneumatik@10\mod_1176211138453_3101.doc @76683

1.1 PneumaticsPos: 3.5/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Kurzbeschreibung/Pneumatik@10\mod_1173180645393_3101.doc @71139a

An I/P module with subsequent pneumatic amplifier is used to controlthe pneumatic actuator. The well-proven I/P module proportionallyconverts the permanent electrical positioning signal from the CPUinto a pneumatic signal used to adjust a 3/3-way valve.

The air flow for pressurizing or depressurizing the actuator iscontinuously adjusted. As a result, excellent control is achieved.When reaching the set point, the 3/3-way valve is closed in centerposition to minimize the air consumption.

Four different pneumatics versions are available: for single-acting ordouble-acting actuators, each with fail-safe or fail-freeze function.

Pos: 3.6/berschriften/1.1.1/2-spaltig/Sicherheitsfunktion"entlftend"@10\mod_1176211744343_3101.doc @76809

1.1.1 Fail-safe functionPos: 3.7/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Kurzbeschreibung/Sicherheitsfunktion"entlftend"@10\mod_1176211673796_3101.doc @76788If the electrical power supply fails, the positioner output 1 isdepressurized, and the pneumatic actuators return spring moves thevalve to the defined safe position. In case of a double-acting actuatorthe second output 2 is additionally pressurized.

Pos: 3.8/======= Spaltenumbruch========@0\mod_1132937966324_3101.doc @3831

Pos: 3.9/berschriften/1.1.1/2-spaltig/Sicherheitsfunktion"blockierend"@10\mod_1176211798765_3101.doc @76830

1.1.2 Fail-freeze functionPos: 3.10/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Kurzbeschreibung/Sicherheitsfunktion"blockierend"@ 10\mod_1176211845484_3101.doc @76851

If the electrical power supply should fail, the positioner output 1 (and2, if applicable) is closed and the pneumatic actuator stops(freezes) the valve in the current position. If compressed air supplyshould fail, the positioner depressurizes the actuator.

Pos: 3.11/ber schriften/ 1.1/2-spalt ig/Bedienung @10\mod_117621 1172234_3101.doc @76704

1.2 OperationPos: 3.12/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Kurzbeschreibung/Bedienung(Kommunikationsmglichkeit) @10\mod_1173184631054_3101.doc @71160

The positioner has a built-in operating panel providing a 2-line LCDand 4 pushbuttons for optimal local configuration, commissioning andoperational monitoring.

Alternatively, the appropriate configuration program and the availablecommunication option can be used.

Pos: 3.13/berschriften/1.1/2-spaltig/Kommunikation@10\mod_1176211201546_3101.doc @76725

1.3 CommunicationPos: 3.14/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Kurzbeschreibung/Kommunikation@10\mod_1176212225390_3101.doc @76893

The standard TZIDC-200 model has a local communication interface(LKS connector). Additionally, a HART communication option forcommunication via the 20 mA signal is available. Bothcommunications are based on the HART Protocol.

Pos: 3.15/berschriften/1.1/2-spaltig/Ein-/Ausgnge@10\mod_1176211233015_3101.doc @76746

1.4 Inputs and outputsPos: 3.16/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Kurzbeschreibung/Ein-/Ausgnge@10\mod_1176212290390_3101.doc @76914

In addition to its input for the analog position set point the TZIDC-200positioner is equipped with a digital input which can be used toactivate various protective functions in the device via the processcontrol system. A digital output allows you to output collective alarmsor fault messages.

Pos: 3.17/ber schriften/ 1.1/2-spalt ig/Modularer Aufbau@ 10\mod_1176211317984_31 01.doc @76767

1.5 Modular designPos: 3.18/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Kurzbeschreibung/ModularerAufbau@10\mod_1173184783043_3101.doc @71181q

The TZIDC-200 basic model can be enhanced at any time byretrofitting optional equipment. Option modules for analog or digitalposition feedback or a shutdown-module can be installed.

Additionally, a mechanical position indicator, proximity switches or24 V microswitches are available for indicating the position

independently of the mother board function.

Pos: 3.19/====Wechselzwei- auf einspaltig==== @0\mod_1130421955859_3101.doc @3829

Wechselein-auf zweispaltigPos: 3.20/======= Seitenumbruch========@0\mod_1126532365768_3101.doc @3830

8/12/2019 TZIDC-200_18348

4/24


4

Pos: 3.21/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Kurzbeschreibung/SchematischeDarstellung@10\mod_1173185518080_3101.doc @71202

Basic model Optional upgrades

Fig. 1: TZIDC-200 schematic diagram

Basic model Optional upgrades

1 LKS plug 9 Plug module for analog feedback (4 20 mA)

2

Positioning signal 4 20 mA 10

Plug-in module for safety shutdown (forced depressurization)

3

Digital input 11

Plug module for digital feedback

4

Digital output DO 12

Installation kit for mechanical position indicator

5

Supply, 1.4 6 bar 13

Installation kit for digital feedback with proximity switches

6

Exhaust 14

Installation kit for digital feedback with 24 V microswitches7

I/P module with 3/3-way valve

8 Position sensor (optional up to 270 rotation angle)

Important

With optional upgrades either the Installation kit for digital feedback with proximity switches (13) or the Installationkit for digital feedback with microswitches 24 V (14) can be used.

In both cases, the mechanical position indicator (8) must be installed.

Pos: 4/===== == Seitenumbruch======== @0\mod_1126532365768_3101. doc @3830

8/12/2019 TZIDC-200_18348

5/24


5

Pos: 5.1/berschriften/1/A- F/Anbauversionen@9\mod_1180950395125_3101.doc @101275

2 Mounting versionsPos: 5.2/==== Wechselein- auf zweispaltig==== @0\mod_1130421847171_3101.doc @3828Wechselein-auf zweispaltigPos: 5.3/berschriften/1.1/2-spaltig/Genormter AnbauanpneumatischeLinearantriebe@10\mod_1176212852312_3101.doc @76956

2.1 To linear actuators in accordance with thestandard

Pos: 5.4/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Montage/Genormter AnbauanpneumatischeLinearantriebe@10\mod_1176213091968_3101.doc @77040

Lateral attachment is in accordance with DIN / IEC 534 (lateralattachment to NAMUR). The required attachment kit is a completeset of attachment material, but does not include the screwed pipeconnections and air pipes.

Pos: 5.5/berschriften/1.1/2-spaltig/Genormter AnbauanpneumatischeSchwenkantriebe@10\mod_1176212899953_3101.doc @76977

2.2 To rotary actuators in accordance with thestandard

Pos: 5.6/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Montage/Genormter AnbauanpneumatischeSchwenkantriebe@10\mod_1176213146937_3101.doc @77061

This attachment is designed for mounting according to the standardVDI/VDE 3845. The attachment kit consists of a console withmounting screws for mounting on a rotary actuator. The adapter forcoupling the positioner feedback shaft to the actuator shaft has to beordered separately. Screwed pipe connections and air pipes have tobe provided on site.


Pos: 5.8/berschriften/1.1/2-spaltig/Integrierter AnbauanRegelventile@10\mod_1176212940421_3101.doc @76998

2.3 Integral mounting to control valvesPos: 5.9/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Montage/Integrierter AnbauanRegelventile, TZIDC-2x0@10\mod_1181809000968_3101.doc @105953

The TZIDC-200 positioner featuring standard pneumatic action isavailable as an option for integral mounting.

The required holes are found at the back of the device.

The benefit of this design is that the point for mechanical strokemeasurement is protected and that the positioner and actuator are

linked internally. No external tubing is required.Pos: 5.10/berschriften/1.1/2-spaltig/BesondereantriebsspezifischeAnbauversionen@10\mod_1176212991062_3101.doc @77019

2.4 Special actuator-specific mountingPos: 5.11/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Montage/BesondereantriebsspezifischeAnbauversionen@10\mod_1173186727709_3101.doc @71265

In addition to the mounting methods described above, there arespecial actuator-specific attachments.

Please contact us for details.


Wechselein-auf zweispaltigPos: 5.13/======= Seitenumbruch========@0\mod_1126532365768_3101.doc @3830

8/12/2019 TZIDC-200_18348

6/24


6

Pos: 5.14/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Montage/AnbauvariantenTZIDC-2x0@10\mod_1178783906328_3101.doc @90413

Fig. 2: Mounting options

1 Mounting to linear actuators acc. to DIN / IEC 534 3 Integral mounting to control valves

2

Mounting to rotary actuators to VDI / VDE 3845 4

Integral mounting to control valves by using an adapter panel

Pos: 6/===== == Seitenumbruch======== @0\mod_1126532365768_3101. doc @3830

8/12/2019 TZIDC-200_18348

7/24


7

Pos: 7.1/berschriften/1/A- F/Betrieb@10\mod_1175678278921_3101.doc @76015

3 OperationPos: 7.2/==== Wechselein- auf zweispaltig==== @0\mod_1130421847171_3101.doc @3828Wechselein-auf zweispaltigPos: 7.3/berschriften/1.1/2-spaltig/Allgemeines@10\mod_1176213970765_3101.doc @77124A

3.1 GeneralPos: 7.4/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Betrieb/Allgemeines@10\mod_1176214294328_3101.doc @ 77292

Microprocessor-based position control in the TZIDC-200 provides foroptimal results. The positioner features high-precision controlfunctions and high operational reliability. Due to their elaboratestructure and easy accessibility, the device parameters can bequickly adapted to the respective application.

The total range of parameters includes:- Operating parameters

- Adjustment parameters

- Monitoring parameters

- Diagnosis parameters

- Maintenance parameters

Pos: 7.5/berschriften/1.1.1/2-spaltig/Betriebsparameter @10\mod_1176214001500_3101.doc @77145

3.1.1 Operating parametersPos: 7.6/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Betrieb/Betriebsparameter @10\mod_1176214346265_3101.doc @77343

The following operating parameters can be set manually if required:

Signal

Signal min. 4 mA, max. signal 20 mA (0 ... 100 %)

freely selectable for split-range operation

min. range 20 % (3.2 mA)recommended range > 50 % (8.0 mA)

Action (positioning signal)

Increasing: Signal 4 ... 20 mA = position 0 ... 100 %

Increasing: Signal 20 ... 4 mA = position 0 ... 100 %

Characteristic curve (travel = f {signal})

Linear, equal percentage 1:25 or 1:50 or 25:1 or 50:1 or freelyconfigurable with 20 reference points.

Travel limit

The positioning travel, i.e. the stroke or angle of rotation, can bereduced as required within the full range of 0 ... 100 %, provided thata minimum value of 20 % is observed.

Shut-off functionThis parameter can be set separately for each end position. Whenthe respective configured limit value is exceeded, the shut-offfunction causes immediate travel of the actuator until reaching the setend position.

When the shut-off value is set to 0, the position is further controlled,even in the respective end position.

Travel time prolongation

This function can be used to increase the max. travel time for fulltravel. This time parameter can be set separately for each direction.

Important

This function can only be used with the pneumatics with thesafety function fail-safe.

Switching points for the positionThis parameter allows you to define two position limits for signaling(see option Module for digital position feedback).

Digital output

The alarms generated in the TZIDC-200 positioner can be polled viathe digital output as a collective alarm.

The desired information can be selected via the operator panel orremotely via the configuration program.

The output can be set to active high or active low, as required.

Digital input

For the digital input, one of the following safety options can beselected. You may use the operators panel or configuration programto select an option.

- No function (default)

- Move to 0 % position- Move to 100 % position

- Hold previous position

- disable local configuration

- Disable local configuration and operation

- Disable any access (no local or remote access via a PC)

The selected function is activated once the 24 V DC signal is nolonger applied (< 11 V DC).

Pos: 7.7/ber schriften/ 1.1.1/2-spal tig/Just ageparameter @10\mod_117621 4036515_3101.doc @77166

3.1.2 Adjustment parametersPos: 7.8/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Betrieb/Justageparameter @10\mod_1176214397515_3101.doc @77364

The TZIDC-200 positioner has a special function for automaticadjustment of the parameters.

Additionally, the control parameters can be set automatically (in

adaptive control mode) or manually to optimally adapt them to theprocess requirements.

Tolerance band

When reaching the tolerance band the position is considered ascorrected. From this point on, the position is further slowly re-adjusted until the dead band is reached. The factory setting for thisparameter is 0.3 %.

Dead band (sensitivity)

When reaching the dead band, the position is held. The factorysetting for this parameter is 0,1 %.

Actuator spring action

Selection of the sensor shaft rotating sense (looking into the opencase), if the valve is moved to the safe position by the actuator spring

(actuator is depressurized via Y1/OUT1).For double-acting actuators the actuator spring action corresponds topressurizing the pneumatic output (OUT2).

Display 0 ... 100 %

Adjusting the display (0 ... 100 %) according to the direction of actionfor opening or closing the valve.

Pos: 7.9/ber schriften/ 1.1.1/2-spal tig/Betri ebsberwachungspar ameter @10\mod_1176214071 453_3101.doc @77187

3.1.3 Monitoring parametersPos: 7.10/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Betrieb/Betriebsberwachungsparameter @10\mod_1176214447375_3101.doc @77385B

Various functions for permanent operational monitoring areimplemented in the TZIDC-200 operating program. The followingstates will be detected and indicated, e.g.:

- 4 ... 20 mA signal out of range

- position out of the adjusted range

- positioning time-out (adjustable time parameter)- position controller inactive

- counter limits (settable in the diagnosis phase) exceeded

While automatic commissioning is in progress, the current state iscontinuously indicated on the integrated LCD.

During operation, the LCD shows the most important processvariables:

- current position (in %),

- malfunctions, alarms, messages (as code)

Access to extended monitoring parameters is possible via HARTcommunication and the DTM.

Pos: 7.11/======= Seitenumbruch========@0\mod_1126532365768_3101.doc @3830

8/12/2019 TZIDC-200_18348

8/24


8

Pos: 7.12/ber schrift en/1.1.1/2- spaltig/Di agnoseparameter @10\mod_11762 14111046_3101.doc @77208

3.1.4 Diagnosis parametersPos: 7.13/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Betrieb/Diagnoseparameter @10\mod_1176214500906_3101.doc @77406

The diagnosis parameters of the TZIDC-200 program inform theoperator about the operating conditions of the valve.

From this information the operator can derive which maintenanceworks are required, and when.

Additionally, limit values can be defined for these parameters. Whenthey are exceeded, an alarm is reported.

The following values are e.g. determined:

- Number of movements performed by the valve- Total travel

The diagnosis parameters and limit values can be called up, set, andreset via HART communication, using the configuration program.

Pos: 7.14/ber schrift en/1.1/2-spa ltig/Bedienpan el@10\ mod_1176214143953_3101. doc @77229

3.2 Operator panelPos: 7.15/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Betrieb/BedienpanelTZIDC-2x0@10\mod_1178871475703_3101.doc @90683

The TZIDC-200 positioners operator panel with four pushbuttonsallows for

- operational monitoring

- manual control

- configuration

- fully automatic commissioning

The operator panel is protected by a hinged cover which can be

opened during operation even in hazardous areas, i.e. the positionercan be locally operated any time as required.


Pos: 7.17/ber schriften/ 1.1.1/2-spal tig/Ein-Tas ten-Inbetri ebnahme@10\ mod_1176214193156_3101.doc @77250

3.2.1 Single-button commissioningPos: 7.18/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Betrieb/Ein-Tasten-Inbetriebnahme@10\mod_1176214842843_3101.doc @77448

Commissioning the TZIDC-200 positioner is especially easy. Thestandard Autoadjust function for automatic adaptation of the deviceparameters can be started by simply pressing a single front panelbutton, and without knowing parameterization details.

Depending on the selected actuator type (linear or rotary), thedisplayed zero position is automatically adapted:

- for linear actuators counter-clockwise (CTCLOCKW)

- for rotary actuators clockwise (CLOCKW).Besides this standard function, a customized Autoadjust function isavailable. The function is launched either via the operators panel orHART communication.

Pos: 7.19/berschriften/1.1.1/2-spaltig/Anzeigen@10\mod_1176214259859_3101.doc @77271

3.2.2 DisplayPos: 7.20/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Betrieb/Anzeigen@10\mod_1176214873937_3101.doc @77469

The information indicated by the 2-line LC display is permanentlyupdated and adapted during operation, to inform the operator in anoptimal way.

During control operation (control with or without adaptation) thefollowing TZIDC-200 data can be called up by pressing thepushbuttons briefly:

- Up button: Current setpoint (mA)

- Down button: Temperature in device

- Up + Down buttons: Current control deviation


Wechselein-auf zweispaltigPos: 7.22/====LeeresModulmiteiner Absatzmarke==== @2\mod_1153381574375_0.doc @35553

Pos: 7.23/====Wechselein- auf zweispaltig==== @0\mod_1130421847171_3101.doc @3828Wechselein-auf zweispaltigPos: 7.24/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Betrieb/Abb. TZIDC-2x0undBedienelemente@10\mod_1176707111062_3101.doc @82068

M00261Fig. 3: TZIDC-200 with removed cover, view of the operator panel

M00235

conf

m

ENTER

MO E

Fig. 4: TZIDC-200 operating elements and display


Wechselein-auf zweispaltigPos: 8/===== == Seitenumbruch======== @0\mod_1126532365768_3101. doc @3830

8/12/2019 TZIDC-200_18348

9/24


9

Pos: 9.1/berschriften/1/G- L/Kommunikation@0\mod_1139412848859_3101.doc @3153Communication

4 CommunicationPos: 9.2/==== Wechselein- auf zweispaltig==== @0\mod_1130421847171_3101.doc @3828Wechselein-auf zweispaltigPos: 9.3/berschriften/1.1/2-spaltig/DTM@10\mod_1176215310421_3101.doc @77511

4.1 DTMPos: 9.4/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Kommunikation/DTM@10\mod_1176215507046_3101.doc @77595

The DTM (Device Type Manager) for TZIDC-200 is based on theFDT/DTM technology (FDT 1.2) and can be integrated in a processcontrol system or loaded in a PC with the DSV401 (SMART VISION)program. This allows you to work with the same user interface in thecommissioning phase, during operation, and for service tasks formonitoring the device, setting parameters, and uploading data.

Communication is based on the HART protocol. It occurs via a localinterface connection (LKS) or in frequency-modulated mode using anFSK-modem connected at any chosen point of the 20 mA signal line.Communication has no effect on operation. Newly set parameters aresaved in the non-volatile memory directly upon the download into thedevice, and become active immediately.

Pos: 9.5/ber schrifte n/1.1/2-spal tig/LKS-Adapt er (RS-232Schni ttstellen wandler) @10\mod_1176215 338250_3101.doc @77532

4.2 LKS adapter (RS-232 interface converter)Pos: 9.6/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Kommunikation/LKS-Adapter (RS-232Schnittstellenwandler) @10\mod_1176215612828_3101.doc @77616

You can easily connect your TZIDC-200 positioner to a PC, e.g., inthe workshop or in the commissioning phase, by using thepositioners LKS adapter (LKS = local communication interface).

An RS-232 interface converter adapts the signals on the serial PCport to the level of the positioners LKS.

Pos: 9.7/berschriften/1.1/2-spaltig/FSK-Modem@10\mod_1176215390421_3101.doc @77553

4.3 FSK ModemPos: 9.8/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Kommunikation/FSK-Modem@10\mod_1176215656328_3101.doc @77637

The FSK modem establishes a digital frequency-modulatedcommunication (Frequency Shift Keying) with the TZIDC-200positioner.

Tapping is possible at any chosen point of the 20 mA signal line.

We recommend that you use an electrically isolated FSK modem. It isbus-compatible when used with isolating amplifiers. Even connectingexplosion-protected field devices is possible, on condition that theFSK modem is run outside the hazardous area.

Fig. 5: Local communication via LKS adapter

1 TZIDC-200

2 LKS adapter

3 Controller

Fig. 6: HART communication with FSK modem via 20 mA signal line

1

TZIDC-200

2 FSK modem

3

Controller

Pos: 9.9/ ==== Wechselzwei- auf einspaltig==== @0\mod_1130421955859_3101.doc @3829

Wechselein-auf zweispaltigPos: 10/==== === Seitenumbruch ======== @0\mod_11265323657 68_3101.doc @3830

8/12/2019 TZIDC-200_18348

10/24


10

Pos: 11.1/berschriften/1/S- Z/TechnischeDaten@0\mod_1132904574837_3101.doc @3169

5 Technical dataPos: 11.2/====Wechselein- auf zweispaltig==== @0\mod_1130421847171_3101.doc @3828Wechselein-auf zweispaltigPos: 11.3/berschriften/1.1/2-spaltig/Eingang@0\mod_1139395051468_3101.doc @3221

5.1 InputPos: 11.4/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/TechnischeDaten/Eingang/ Stellsignal(Zweileitertechnik) @10\mod_1176272560140_3101.doc @77936

Output signal (two-wire technology)

Nominal range 4 ... 20 mA

Split range configurationbetween

20 ... 100 %

of the nominal range

Max. 25 mAMin. 3.6 mA

Starting at 3,8 mA

Load voltage at 20 mA 9,7 V

Impedance at 20 mA 485

Digital input

Control voltage 0 ... 5 V DC logical switchingstate "0"

11 ... 30 V DC logical switchingstate "1"

Current max. 4 mA

Pos: 11.5/berschriften/1.1/2-spaltig/Ausgang@10\mod_1176215873937_3101.doc @77658

5.2 OutputPos: 11.6/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/TechnischeDaten/Ausgang/ Druckluftausgang@10\mod_1176272620812_3101.doc @77957

Compressed air output

Range 0 ... 6 bar (0 ... 90 psi)

Air capacity 5.0 kg/h = 3.9 Nm/h = 2.3 sfcm

at 1.4 bar (20 psi) supply pressure

13 kg/h = 10 Nm/h = 6,0 sfcm

at 6 bar (90 psi) supply pressure

Output function For single or double-actingactuators, air is vented fromactuator or actuator is blocked incase of (electrical) power failure

Shut-off values End position 0 % = 0 ... 45 %

End position 100 % = 55 ... 100 %

Digital output (control circuit to DIN 19234/NAMUR)

Supply voltage 5 ... 11 V DC

Current > 0.35 mA < 1.2 mA Switching state logical "0"

Current > 2.1 mA Switching state logical "1"

Effective direction (configurable) normally logical "0" or logical "1"

Pos: 11.7/berschriften/1.1/2-spaltig/Stellweg@10\mod_1176215894234_3101.doc @77679

5.3 TravelPos: 11.8/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/TechnischeDaten/Stellweg/ Drehwinkel@10\mod_1176272774203_3101.doc @77978

Rotation angle

Used range 25 ... 120 (rotary actuators,optional 270)

25 ... 60 (linear actuators)Travel limit Min. and max. limits, freelyconfigurable between0 ... 100 % of total travel (min.range > 20 %)

Travel time prolongation Range of 0 ... 200 seconds,separately for each direction

Dead band time limit Range 0 ... 200 seconds(monitoring parameter forcontrol until the deviationreaches the tolerance band)


Pos: 11.10/berschriften/1.1/2-spaltig/Luftversorgung@10\mod_1176215914875_3101.doc @77700

5.4 Air supplyPos: 11.11/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/TechnischeDaten/LuftversorgungTZIDC-2x0@10\mod_1180951671703_3101.doc @101588

Instrument air free of oil, water and dust acc.to DIN / ISO 8573-1pollution and oil contentaccording to Class 3 (purity:max. particle size: 5 m, max.particle density: 5 mg / m3; oilcontent: max. concentration: 1mg / m3; pressure dew point:10 K below operatingtemperature

Supply pressure 1.4 ... 6 bar (20 ... 90 psi)

Note: Do not exceed the max.operating pressure of theactuator!

Air consumption < 0.1 kg/h / 0.05 scfm(independent of supplypressure)

Pos: 11.12/berschriften/1.1/2-spaltig/bertragungsdatenundEinflussgren@10\mod_1176215939812_3101.doc @77721

5.5 Transmission data and influencesPos: 11.13/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/TechnischeDaten/bertragungsdatenundEinflussgren@10\mod_1176272844734_3101.doc @78020

Output Y1

Increasing Increasing output signal 0 ... 100 %

Increasing pressure at output

Decreasing Increasing output signal 0 ... 100 %

Decreasing pressure at output

Action (positioning signal)

Increasing Signal 4 ... 20 mA =

actuator position 0 ... 100 %

Decreasing Signal 20 ... 4 mA =

actuator position 0 ... 100 %

Characteristic curve (travel = f {signal})

Linear, equal percentage 1:25 or 1:50 or 25:1 or 50:1 and freelyconfigurable with 20 reference points.

Characteristic deviation < 0,5 %

Tolerance band 0.3 ... 10 %, adjustable

Dead band 0,1 ... 10 %, adjustable

Resolution (A/D conversion) > 4000 steps

Sample rate 20 ms

Influence of ambient temperature < 0.5 % per 10 K

Influence of vibration < 1 % to 10 g and 80 Hz

Seismic requirements

Meets requirements of DIN / IEC 68-3-3 Class III for strong andstrongest earthquakes.

Influence of mounting orientation

Not measurable.

Meets the requirements of the following directives

- EMC Directive 89 / 336 / EWG as of May 1989

- EC Directive for CE conformity marking

Communication

- HART Protocol 5.1

- Local connector for LKS (local communication interface) adapter

- HART communication via 20 mA signal line with (optional) FSKmodem

Pos: 11.14/== ===== Spaltenumbruch======= = @0\mod_113293796 6324_3101.doc @3831

8/12/2019 TZIDC-200_18348

11/24


11

Pos: 11.15/berschriften/1.1/2-spaltig/KlimatischeBeanspruchung@10\mod_1176215985578_3101.doc @77742

5.6 Environmental capabilitiesPos: 11.16/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/TechnischeDaten/KlimatischeBeanspruchung@10\mod_1176272943953_3101.doc @78041

Ambient temperature

For operation, storage andtransport:

-40 85 C (-40 ... 185 F)

When using proximity switchesSJ2-S1N (NO):

-25 85 C (-13 ... 185 F)

Relative humidity

Operational (with closed housingand air supply switched on):

95 % (annual average),condensation permissible

Transport and storage: 75 % (annual average), non-condensing

Pos: 11.17/berschriften/1.1/2-spaltig/Gehuse@10\mod_1176216027484_3101.doc @77763

5.7 HousingPos: 11.18/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/TechnischeDaten/GehuseTZIDC-200@10\mod_1176708472718_3101.doc @82221

Material/Protections

Aluminum, protection class IP 65 / NEMA 4X

Surface/color

Electrostatic dipping varnish with epoxy resin, stove-hardened. Casevarnished black, RAL 9005, matte, housing cover Pantone 420.

Electrical connectionsScrew terminals: Max. 1.0 mm2for options,Max. 2.5 mm2for analog signal.

Note: Do not expose the terminals to strain.Cable entry: 2 tap holes 1/2-14 NPT or

M20 x `1.5 (cable gland or pipe plug must beordered separately)

Pneumatic connections

Threads G 1/4 or 1/4-18 NPT

Weight

3,0 kg

Mounting orientation

any orientation allowed

Dimensions

see dimensional drawings

Pos: 11.19/= ====== Spaltenumbruch======= = @0\mod_1132937966324 _3101.doc @3831

Pos: 11.20/berschriften/1.1/2-spaltig/Sicherheitsintegrittslevel@10\mod_1176216055937_3101.doc @77784

5.8 Safety Integrity LevelPos: 11.21/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/TechnischeDaten/Sicherheitsintegrittslevel@13\mod_1191309977312_3101.doc @126333

Important

Applies to applications with single-acting and depressurizingpneumatics.

The positioner TZIDC-200 and the emergency shutdown module forTZIDC-200 meet the requirements regarding:

- functional safety in accordance with IEC 61508 / IEC 61511-1

- explosion protection (depending on the model)

- electromagnetic compatibility in accordance with EN 61000

In case of a failure of electrical power or compressed air supply orwhen a positioner malfunction occurs, the actuator is depressurizedby the positioner, and the return spring in the actuator moves thevalve to a pre-defined, safe end position (either OPEN or CLOSED).

SIL specific safety-related characteristics:

TZIDC-200 Emergency shutdownmodule for TZIDC-200

Category SIL2 SIL2

SFF 85 % 94 %

PFDav 6.89 x 10-4 1.76 x 10-4

dd + s 925 FIT 718 FIT

du 157 FIT 40 FIT

For details refer to the Management Summary in the SIL-SafetyInstructions 37/18-79XA.

Pos: 11.22/== ===== Spaltenumbruch======= = @0\mod_113293796 6324_3101.doc @3831

8/12/2019 TZIDC-200_18348

12/24


12

Pos: 11.23/berschriften/1.1/2-spaltig/Explosionsschutz@10\mod_1176216136218_3101.doc @77805

5.9 Explosion protectionPos: 11.24/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/TechnischeDaten/ExplosionsschutzTZIDC-200@10\mod_1176711825609_3101.doc @82410

Important

The values indicated here are taken from the respectiveapproval certificates.

Always observe the specifications and supplements in thecertificates.

(see operating instructions).

FM Approval HLC 8/02 3010829Explosion proof; enclosure 4X; T5, max. 82 C

CL I; Div 1; Grp. C-D

Intrinsically safe; enclosure 4X; T5, max. 82 C

CL I, II, III; Div 1; Grp. A-B-C-D-E-F-G

Non-incendive, enclosure 4X; T4, max. 85 C

CL I; Div 2; Grp. A-B-C-D

CL II, III; Div 2; Grp. F-G

Dust ignition-proof; enclosure 4X; T5, max. 82 C

CL II, III; Div 1; Grp. E-F-G

CSA Certification 1393920

Explosion proof; enclosure 4X; T5, max. 85 CCL I; Div 1; Grp. C-D

CL II; Div 1; Grp. E-F-G

CL III

Intrinsically safe; enclosure 4X; T5, max. 82 C

CL I; Div 1; Grp. A-B-C-D

CL II; Div 1; Grp. E-F-G

CL III

ATEX / GOST Russia /GOST Ukraine

II 2G EEx d II C T4/T5/T6

Prototype test certificate: DMT 02 ATEX E 029 X

Type: Flameproof enclosure

Device class: II 2G (EEx ib IIC)

Temperature class: T4, T5, T6

Permissible ambienttemperature:

T4: -40 C < Tamb< 85 C

T5: -40 C < Tamb< 80 C

T6: -40 C < Tamb< 65 C

ATEX II 2G EEx ib IIC T6

Prototype test certificate: TV 98 ATEX 1370 X

Type: Intrinsically safe equipment

Device class: II 2G (EEx ib IIC)


Permissible ambienttemperature:

T4: -40 C < Tamb< 85 C

T5: -40 C < Tamb< 50 C

T6: -40 C < Tamb< 35 C

IECEx Ex ib IIC T6

Prototype test certificate: IECEx TUN 04.0015X, Issue no.:0

Type: Intrinsically safe


Permissible ambienttemperature: T4: -40 C < Tamb

< 85 C

T5: -40 C < Tamb< 50 C

T6: -40 C < Tamb< 35 C

Pos: 11.25/berschriften/1.1/2-spaltig/Optionen@10\mod_1176216171890_3101.doc @77826

5.10 OptionsPos: 11.26/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/TechnischeDaten/OptionenTZIDC-200@10\mod_1180689072031_3101.doc @100723

Module for analog position feedback1)

Signal range 4 ... 20 mA (configurable splitranges)

Supply, 2-wire circuitry 24 V DC (10 ... 30 V DC)

48 V DC (20 ... 48 V DC,

no ignition protection)

Characteristic curve(configurable)

Rising or falling

Characteristic deviation < 1 %

Important

Without a signal from the positioner (e.g., no energy orinitializing) the module sets the output to > 20 mA (alarmlevel)

Module for digital position feedback1)

Two switches for digital position feedback (position adjustable withinthe range of 0 ... 100%, ranges cannot overlap)

Current circuits acc. to DIN 19234 / NAMUR


Signal current < 1.0 mA Switching state logical 0

Signal current > 2,0 mA Switching state logical 1

Direction of action normally logical 0 or logical 1(configurable)

Module for the emergency shutdown function2)

Supply voltage 24 V DC (20 ... 30 V DC)(galvanically isolated from inputsignal)

Safe position is activated when voltage < 5 V

Explosion protection see certificate (operating

instructions)SIL See Explosion protection

A separate 24 V DC signal is normally applied to the emergencyshutdown module, which connects through the signal from themicroprocessor to the I/P module.When the 24 V DC signal is interrupted, the pneumatic moduleexecutes the respective safety function, depending on themechanical construction:

The positioner output 1 is depressurized, and the valve is moved tothe safe position. In case of a double-acting actuator the secondoutput 2 is additionally pressurized.

Important

The emergency shutdown module can only be used withpneumatics with the safe position fail-safe.

8/12/2019 TZIDC-200_18348

13/24


13

The emergency shutdown module works independently of the motherboard, i.e. all information from the final control element is available inthe supervisory process control system at any time.

1) The module for analog position feedback and the module fordigital position feedback plug in separate slots and can be usedtogether.

2) The module for the emergency shutdown function uses the same

space as the module for analog feedback and the module foranalog or digital feedback and cannot be plugged in and runtogether with any of them.

Digital position feedback with proximity switches

Two proximity switches for independent position signaling. Switchingpoints adjustable between 0 100 %

Current circuits acc. to DIN 19234 / NAMUR


Signal current < 1.0 mA Switching state logical 0

Signal current > 2,0 mA Switching state logical 1

Direction of action (logical state)

Position

Proximity switch < Lim. 1 > Lim. 1 < Lim. 2 > Lim. 2

SJ2-SN (NC) 0 1 1 0

SJ2-S1N (NO) 1 0 0 1

Important

When using SJ2_S1N (NO), the TZIDC-200 positioner mayonly be used at an ambient temperature range from -25 ... 85 C (-13 ... 185 F).

Digital position feedback with 24 V microswitches

Important

Only approved for Ex d version!

Two microswitches for independent position signaling. Switchingpoints adjustable between 0 100 %.

Voltage max. 24 V AC / DC

Load rating max. 2 A

Contact surface 10 m Gold (AU)

Mechanical position indicator

Indicator disk in enclosure cover, linked with positioner feedback

shaft through magnetic coupling.

Important

These options are also available for retrofitting by Service.

Pos: 11.27/= ====== Spaltenumbruch======= = @0\mod_1132937966324 _3101.doc @3831

Pos: 11.28/ber schriften/ 1.1/2-spalt ig/Zubehr @10\mod_117621620 4812_3101.doc @77847

5.11 AccessoriesPos: 11.29/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/TechnischeDaten/Zubehr TZIDC-200@10\mod_1176713261968_3101.doc @82461

Mounting material

Attachment kit for linear actuators to DIN/IEC 534 / NAMUR

Attachment kit for rotary actuators to VDI/VDE 3845

Attachment kit for integral mounting to control valves

Attachment kit for actuator-specific attachment upon request

EEx d cable glands

Cable gland and pipe plug approved for Ex d, securing adhesive

Pressure gauge block

With pressure gauges for supply and output pressure. Pressuregauges with housing 28 mm,, with connection block in aluminum,black with installation material for mounting toTZIDC-200.

Filter regulator

All metal version in brass, varnished black, bronze filter element,40 m, with condensate drain.

max. pre-pressure 16 bar, output adjustable to 1.4 ... 6 bar

PC adapter for communication

LKS adapter f. plug conn. to TZIDC-200

FSK modem for HART communication

(see data sheet 63_6.71 DE)

PC software for remote configuration and operation

DSV401 (SMART VISION) with DTM for TZIDC/TZIDC-200 availableon CD ROM (see data sheet 63_1.20 EN)


Wechselein-auf zweispaltigPos: 12/==== === Seitenumbruch ======== @0\mod_11265323657 68_3101.doc @3830

8/12/2019 TZIDC-200_18348

14/24


14

Pos: 13.1/berschriften/1/A- F/Elektrischer Anschluss@0\mod_1140620471687_3101.doc @ 3143

6 Electrical connectionPos: 13.2/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Elektrischer Anschluss/Elektrischer Anschluss200@11\mod_1183551089984_3101.doc @109643

M00313

1

2

3

6

7

4

5

+41

-42

Limit

2

+5

1

-52

L

imit

1

+11

-12

+81

-82

+83

-84

+51

-52

+41

-42

+31

-32

8

9

Fig. 7: Screw terminals, overview

1 Module for analog position feedback

2

Module for digital feedback or service switch of emergencyshutdown module

3

Module for digital feedback or terminals for emergencyshutdown module

4 Digital position feedback, either proximity switches or 24 Vmicroswitches

5 Digital position feedback, either proximity switches or 24 V

microswitches6

Digital output DO

7

Digital input

8

Signal 4 ... 20 mA

9

Grounding screw

8/12/2019 TZIDC-200_18348

15/24


15

Fig. 8: Pin configuration

A Basic model

B Options

1 Analog input

2 Digital input

3 Digital output DO

4

Digital feedback

5

Analog feedback

6

Proximity switches

7

Microswitches

8

Emergency shutdown module

Pos: 14/==== === Seitenumbruch ======== @0\mod_11265323657 68_3101.doc @3830

8/12/2019 TZIDC-200_18348

16/24


16

Pos: 15.1/ber schrift en/1/M- R/Mabilder @2\mod_1151313449 156_3101.doc @31849

7 DimensionsPos: 15.2/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Mabilder/Mabilder TZIDC-2x0@10\mod_1176714385562_3101.doc @82545

All dimensions in mm (inch)

Fig. 9: Top viewA Tap hole M8 (10 mm low)

B Tap hole M6 (8 mm low)

C Tap hole M5 x 0.5 (air connections in version for integral mounting)

D Sensor shaft (larger than scale)

Fig. 10: Left and right side view

A NPT or M20 x 1.5 B Pneumatic connections, NPT -18 or G1/4

8/12/2019 TZIDC-200_18348

17/24


17

Fig. 11: Bottom view

A Pneumatic connections, NPT 1/4"-18 or G1/4"

M00300

45

/7

5

(1

.77

/2

.95)

25

(0

.99)

75

(2

.95)

30 / 53

(1.18 / 2.09)

B*

A*

Mounting to linear actuators to DIN/IEC 534Mounting to rotary actuators to VDI/VDE 3845

*) Dimensions A and B are dependent on the rotary actuator

Fig. 12: Mounting drawings

8/12/2019 TZIDC-200_18348

18/24


18

M00301

40 (1.58)120 (4.73)

97

(3

.82)

Fig. 13: Positioner TZIDC-200 with pressure gauge block and filter regulatorPos: 16/==== === Seitenumbruch ======== @0\mod_11265323657 68_3101.doc @3830

8/12/2019 TZIDC-200_18348

19/24


19

Pos: 17.1/berschriften/1/A- F/Bestellinformationen@0\mod_1139397854370_3101.doc @3141Order information

8 Ordering informationPos: 17.2/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Bestellinformationen/BestellinformationenTZIDC-200 @10\mod_1176714838156_3101.doc @82613

Electro-Pneumatic Positioner Variant digit No. 1 - 7 8 9 10 11 12 13 14 Code

TZIDC-200 with Flameproof Enclosure Catalog No. 18348- 0intelligent, software-configurable with local communicationinterface (LKS) and HART communication

Case / MountingCase made of aluminium, varnished, protection IP 65 (NEMA 4X)

for mounting to linear actuators acc. to DIN/IEC 534 / NAMURor to rotary actuators acc. to VDI/VDE 3845 1

as above, but with mechanical position indicator 2for integral mounting to control valves 3

as above, but with mechanical position indicator 4for mounting to rotary actuators acc. to VDI/VDE 3845with extended rotation angle up to 270 5

as above, but with mechanical position indicator 6

See Options/Accessories for customer-specific mountingPlease specify the actuator type and type of mounting

Note:Special mounting material is required

(see "Accessories")

Operationwith operator panel and display integrated in the enclosure cover 1

Explosion protectionATEX Ex II 2 G EEx d IIC T4, T5, T6 1FM/CSA Class 1, Div. 1, Group C-D (explosion-proof) 1) 2

ATEX EEx ib and EEx d IIC T6 3FM/CSA intrinsically safe and explosion-proof 1) 4IECEx Ex ib IIG T6 5GOST Russia Ex d IIC T4/T5/T6 Dother explosion protection certificates upon request

Output / safe position (in case of an electrical power failure)Single acting, fail safe 1

fail freeze 2Double acting, fail safe 3

fail freeze 4

Connections 2)Cable: Thread M20 x 1.5 Air pipe: Thread G 1/4 1Cable: Thread M20 x 1.5 Air pipe: Thread 1/4-18 NPT 2Cable: Thread 1/2-14 NPT Air pipe: Thread 1/4-18 NPT 3

Option modules for analog or digital position feedbackwithout 0

Plug-in module analog position feedback, sign. range 4...20 mA,for two-wire 1

digital position feedback 3analog position feedback, sign. range 4...20 mA,

two-wire, and digital position feedback 4shutdown module 3) 5

Continued on next page1) only with cable connection NPT thread2) EEx d cable glands see accessories3) only for fail safe pneumatic


8/12/2019 TZIDC-200_18348

20/24


20

Pos: 17.4/berschriften/1.1/1-spaltig/A- F/FortsetzungBestellinformationen@6\mod_1169193551531_3101.doc @61633

8.1 Ordering information (continued)Pos: 17.5/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Bestellinformationen/FortsetzungBestellinformationenTZIDC-200@10\mod_1176714848265_3101.doc @82655

Electro-Pneumatic Positioner Variant digit No. 1 - 7 12 13 14 15 16 17 18 Code

TZIDC-200 with Flameproof Enclosure Catalog No. 18348-intelligent, software-configurable with localcommunication interface (LKS) and HART communication

Optional mechanical kit for digital position feedbackwithout 0

Mechanical kit for digital position feedbackwith proximity switches SJ2-SN (NC or logical 1) 1

with proximity switches SJ2-S1N (NO or logical 0) 4) 2with 24 V DC/AC microswitches (change-over contacts) 5) 3

Parameter setting / bus addressFactory setting for HART devices 1Customized parameter setting for HART devices 2

Design (varnish / coding)Standard 1

As specified (on request) 2

Device identification label (provide list, if available)without 0label including text (plain text, max. 16 letters)

with separate sticker 1with separate stainless steel label 18.5 x 65 mm 2 os: 17.6/==== LeeresModulmitzwei Absatzmarken==== @3\mod_1159257408468_0.doc @42813

Pos: 17.7/berschriften/1.1/1-spaltig/S- Z/ZustzlicheBestellinformationen@8\mod_1175766342062_3101.doc @76273

8.2 Additional ordering informationPos: 17.8/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Bestellinformationen/ZustzlicheBestellinformationenTZIDC-200@10\mod_1176714852671_3101.doc @82676Code

CertificatesSIL2 - Declaration of conformity 6) CS2

Certificate of compliance with the order acc. to EN 10204-2.1 (DIN 50049-2.1) CF1Certificate of compliance with the order acc. to EN 10204-2.1 (DIN 50049-2.1) with item description CF2Test Report acc. to EN 10204-2.2 (DIN 50049-2.2) CF3

Inspection certificate 3.1 acc. to EN 10204 with max. deviation CBA

4) only for ambient temperature range -25...+85 C5) only for Ex d version6) only for single acting and fail safe pneumatic


8/12/2019 TZIDC-200_18348

21/24


21

Pos: 17.10/berschriften/1.1/1-spaltig/A- F/Bestellinformationen, Zubehr 1@8\mod_1175763415390_3101.doc @ 76189Bestellangaben

8.3 Order information, accessories 1Pos: 17.11/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/TZIDC/ TZIDC-200/Bestellinformationen/BestellinformationenTZIDC-200, Zubehr 1@10\mod_1176714842796_3101.doc @82634

TZIDC-200 Catalog No.

Mounting material and costAttachment kit for linear actuators(lateral attachment to DIN/IEC 534 / NAMUR) stroke 10 ... 35 mm 7959125

stroke 20 ... 100 mm 7959126Attachment kit for rotary actuators (mounting to VDI/VDE 3845)consisting of:

a) Adapter (shaft coupler) 7959110

b) Mounting bracket dimension A/B = 80/20 mm 319603dimension A/B = 80/30 mm 319604dimension A/B = 130/30 mm 319605dimension A/B = 130/50 mm 319606

Pressure gauge block including attachment materialfor single acting TZIDC-200 with 2 pressure gauges 28 mm(1 x for air supply and 1 x for output pressure)G 1/4 connections Supply pressure range

0...10 bar/ 0...140 psiOutput pressure range 0...4 bar/ 0...60 psi 7959111

0...10 bar/ 0...140 psi 79591121/4-18 NPT connections Supply pressure range


0...10 bar/ 0...140 psi 7959114for double acting TZIDC-200 with 3 pressure gauges 28 mm(1 x for air supply and 2 x for output pressure)G 1/4 connections Supply pressure range


0...10 bar/ 0...140 psi 79591161/4-18 NPT connections Supply pressure range


0...10 bar/ 0...140 psi 7959118(Pressure gauge blocks are delivered as separate unitsfor mounting by the customer)

Filter regulator, brass incl. material for mountingto pressure gauge block

connections thread G 1/4 7959119thread 1/4-18 NPT 7959120

(Filter regulators are delivered as separate unitsfor mounting by the customer)

Adapter and operating program for digital communicationLKS adapter see Data Sheet 10/63-6.71 ENFSK modem see Data Sheet 10/63-6.71 ENDSV401 (SMART VISION) on CD-ROM see Data Sheet 10/63-1.20 EN

EEx d cable glands 7)1 x EEx d cable gland M20 x 1.5,

1 pipe plug M20 x 1.5, securing adhesive 79592442 x EEx d cable glands M20 x 1.5,

securing adhesive 79592451 x EEx d cable gland 1/2" NPT,

1 pipe plug 1/2" NPT, securing adhesive 79592462 x EEx d cable glands 1/2" NPT,

securing adhesive 7959247

7) for cable diameter 7.2...11.7 mm


8/12/2019 TZIDC-200_18348

22/24


22


8.4 Order information, accessories 2Pos: 17.14/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Bestellinformationen/Bestellinformationen, Zubehr 2@10\mod_1175763138078_3101.doc @76126

TZIDC , TZIDC-110, TZIDC-120, TZIDC-200, TZIDC-210, TZIDC-220 Catalog No.Attachment kit for Manufacturer / TypeAir Torque SC 30 9) 319604Air Torque SC-P-60-4 9) 319604Air Torque SR 30 9) 319603ARI DP32, DP33, DP34 7959125AMG SAD 010 ... SAF 040 9) 319603AMG SAD 040 ... SAF 050 9) 319605

ARCA 812 stroke 30 mm 7959107ARCA 812 stroke 60 mm 7959106ARCA 813 stroke 30 mm 7959109ARCA 813 stroke 60 mm 7959108Automax DA 85 ... DA150 9) 319603Badger Meter ATC 754/755 7959123bar GTE / GTD 045 ... 127 9) 319604bar GTE / GTD 143 ... 254 9) 319605Bray 92 / 93 series 9) 319603Conovalve Series 740.000 / 750.000 / 770.000 / 795.000 7959125El-O-Matic ED / ED / PE / PD 500 ... 4004 9) 319605El-O-Matic ED / ED / PE / PD 25 ... 350 9) 319603FESTO DRD-4-F05 ... DRD-50F10 9) 319603FESTO DRD-77-F10 ... DRD-255-F14 9) 319605Fisher 1051-30, 1052-30 7959214Fisher 1061 size 130 7959206Fisher 471 7959195Fisher 585 C 7959250Fisher 657 / 667 Size 10 ... 30 mm 7959177Flow Serve DA 85 ... 150 9) 319603Foxboro FoxPak IP127 / V725 7959168Foxboro V713 stroke 10 ... 35 mm 7959125Foxboro V713 stroke 25 ... 90 mm 7959126GEFA AC 020 ... AC 1750 9) 319604GEFA MC 063 FA 9) 319603GEM 690/25 and 50 7959103GEM CleanStar 7959125Gulde DK 7959161

9) need additional Adapter (Shaft Coupler), Catalog No. 7959110


8/12/2019 TZIDC-200_18348

23/24


23


8.5 Order information, accessories 3Pos: 17.17/TechnischeDaten/ Datenblatt/Aktorik/Stellungsregler/Allgemein/Bestellinformationen/Bestellinformationen, Zubehr 3@10\mod_1175763193171_3101.doc @76147

TZIDC , TZIDC-110, TZIDC-120, TZIDC-200, TZIDC-210, TZIDC-220 Catalog No.Attachment kit for Manufacturer / TypeHoneywell 600-11, 600-15 7959126Hytork XL26 ... XL680 9) 319603Hytork XL1125, XL1370, XL2585, XL4580 9) 319605Keystone 79U/E-002(S) ... 79U/E-181(S) 7959147Mapag A/F 30 ... A/F 500 9) 319603Masoneilan CAMFLEX II, VARIMAX, MINITORK II 7959144

Masoneilan VariPak 28000 series 7959163MaxFlo MaxFlo 7959140NAF 791290 7959207NAMUR stroke 10 ... 35 mm 7959125NAMUR stroke 25 ... 90 mm 7959126NAMUR stroke 100 ... 170 mm 7959339NELES B1JU8, B1J8U, B1CU9/20E, B1CU17/55, B1CU13-32, 9) 319603

B1C6U-20U, 1JAU10/20, BC6U-20UNELES BC6-20, B1C6-20, BJ8-20, B1J8-20 7959146Norbro 10AR40, 20BR40, 20AR40, 20RDA40, 15AR40, 15BR40 9) 319603Norbro 25AR40, 25BR40, 35AR40, 35BR40, 33-40, 30AR40 9) 319604Norbro 45BR40, 45AR40 9) 319606Prisma PP10, PP20 9) 319604Prisma PPW 9) 319603Remote Control RCD 05-DA/SR ... RCD 60-DA/SR 9) 319603Revo FD/FS 12, 25, 50 9) 319603Revo FD/FS 90, 130, 180, 205, 306 9) 319605Richter RA-1/2 046 ... RA-1/2 127 9) 319604Richter RA-1/2 185 ... RA-1/2 300 9) 319605Samson 241, 271, 3271 7959145Samson 3277 7959136Schubert&Salzer GS 8020 / 8021 / 8023 7959200SED SED stroke 100 mm 7959141VDI / VDE 3845 80 / 20 mm 9) 319603VDI / VDE 3845 80 / 30 mm 9) 319604VDI / VDE 3845 130 / 30 mm 9) 319605VDI / VDE 3845 130 / 50 mm 9) 319606

9) need additional Adapter (Shaft Coupler), Catalog No. 7959110

Pos: 18/Rck seiten/Minden _Aktorik @2\mod_11515750816 40_3101.doc @32243===== Endeder Stckliste=====

8/12/2019 TZIDC-200_18348

24/24

ABB has Sales & Customer Support

expertise in over 100 countries worldwide.

www.abb.com/instrumentation

The Companys policy is one of continuous product

improvement and the right is reserved to modify the

information contained herein without notice.

Printed in the Fed. Rep. of Germany (10.2007)

ABB 2007

3KXE341004R1001

10/18-0.3

2-EN

Rev.

E

ABB Limited

Salterbeck Trading EstateWorkington, CumbriaCA14 5DS

UK

Tel: +44 (0)1946 830 611Fax: +44 (0)1946 832 661

ABB Inc.

125 E. County Line Road

Warminster, PA 18974

USA

Tel: +1 215 674 6000

Fax: +1 215 674 7183

ABB Automation Products GmbH

Schillerstr. 72

32425 Minden

Germany

Tel: +49 551 905-534

Fax: +49 551 905-555

[email protected]

tzidc-200_18348

Documents