trax eh · panels that trax eh holders and proles are installed on and assembly instructions for...
TRANSCRIPT
WARNINGBefore installing this product, read and follow all warning notices and instructions accompanying this product. Failure to adequately install this product can result in severe injury, or property damage. Please send an e-mail request to [email protected] for additional paper or electronic copies of these instructions.Please observe the maximum weight loads specified in our sales documentation. Tools required for installation are not supplied.
SAVE THESE INSTRUCTIONSThis manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment.
Installation manual2nd series profiles
` The longest shelf life.
Trax EH
Safety first
It is highly recommended that all persons involved in design, installation, disassembly and use of these products carefully study this document to become fully aware of the safety measures that must be followed.
Only qualified personnel must be used for design, Installation and disassembly of Trax EH holders and profiles.
Unless specifically authorised in this document, non of the electrical components shall be altered.
Safety of this product is subject to:
• Not exceeding the indicated nominal current (A) • Keeping within recommended weight loading specifications as per this document and other CUBIC literature• Installation according to instructions demonstrated in this document.• Installation only on structurally sound and appropriate walls and mid floor furniture• Structurally used panels being strengthened to prevent bowing• A safety check being performed before drilling into any surface• Use of products only upon completion of installation• Appropriate use of the products• Using only original or approved accessories for Trax EH holders and profiles• Using only tempered (safety) glass• Not making any alterations and adaptation where not appropriate and not approved by CUBIC • Maintaining a common level of caution and alertness when in use• Keeping away anyone whom is not qualified to use these products, in particular children• Conducting regular checks to ensure there are no signs of damage• In case of damage discontinuing use until appropriate repairs have been made • Observing national regulations• Observing accident prevention regulations
Power supply
For detailed specifications and instructions on installation and operation of the power supply, please refer to the documentation provided with the power supply.
Access to power supply
Access to the power supply must be restricted from general users. Access to be possible only with a tool (example: a screw driver to be used to remove a screw to release a latch).
For all electrified holder and profile options, access to the power supply must be kept for inspection and maintenance. Adequate ventilation for the power supply must be allowed.
Please be aware of the depth of the power supply in planning and preparation of the walls and panels; especially if the power supply is to be housed behind the Trax EH panels. This information can be found in the documentation provided with the power supply.
Installation guide by example
The primary focus of this section is to provide the required processing data for the panels that Trax EH holders and profiles are installed on and assembly instructions for fixing the holders and profiles to the panel and substructure.Examples provided within for fixing of holders, profiles and panels to substructure are examples only and may vary based on application.
EX-PM-051
Depth
Electrified EH profile for 19mm wooden panel (floating installation)
10
Electrified EH profile for 19mm wooden panel (continuous installation)
22
EH profile for 19mm wooden panel (floating installation)
6
EH profile for 19mm wooden panel (continuous installation)
16
4 ` 5 `EX-PM-051
6 ` 7 `
EH profile for 19mm wooden panel (floating installation) Router processing data of 19mm (3/4”) wooden panel
19mm ( 3/4")
R6.9+0.20
-0.00
R11.7
L(c)=L(p)+5mm
Thickness:19mm
12mm
L(p)
L (c)
16mm
EX-PM-051
8 ` 9 `
Prevent the panel frombowing by strengtheningthe panel from the rear.Example: using woodenbeams shown.
Ø3mm × D15mm
Insert the End cap onto the profile and press firmly until abuts the profile. Ensure the profile is the correct side up, before inserting the profile into the processed wooden panel; see diagram.
1
Fix the profile onto panel by Inserting and fastening the self tapping screwsincluded. If necessary, you may also drill 15mm deep, 3mm holes prior tofastening screws.
2
up
EX-PM-051
Profile must NOT be recessed from the front face of the panel.
11 `
Electrified EH profile for 19mm wooden panel (floating installation)
10 `
Router processing data of 19mm (3/4”) wooden panel
WARNING!
The electrical components of this product must be installed and inspected by qualified personnel.
Do not make alteration to this product, unless specifically authorised in installation guidelines.
Only CUBIC approved accessories are to be used with this product. For further assistance please contact us at [email protected].
19mm ( 3/4")
L(c)=L(p)+30mm
Thickness:19mm
12mm
25mm (1")
L(p)
R11.7
L (c)
R6.9+0.20
-0.00
16mm
EX-PM-051
12 ` 13 `
Insert the End cap onto the profile and press firmly until abuts the profile. Ensure the profile is the correct side up, before inserting the profile into the processed wooden panel; see diagram.
Insert the power plug as shown on the left side of the profile and secure with the screw. Insert the End cap onto the plug and press firmly until abuts the plug.
Please note:> Before attaching the End cap, ensure the End cap cover is inserted. > The copper wires are to extend beyond insert (plastic) by 15mm on the left.
2
up
1
Red+
Black−
EX-PM-051
Profile must NOT be recessed from the front face of the panel.
15mm
14 ` 15 `
Prevent the panel frombowing by strengtheningthe panel from the rear.Example: using woodenbeams shown.
Ø3mm × D15mm
Fix the profile onto panel by Inserting and fastening the self tapping screws included. If necessary, you may also drill 15mm deep, 3mm holes prior to fastening screws.
3
EX-PM-051
EH profile for 19mm wooden panel (continuous installation)
16 ` 17 `
Router processing data of wooden panel
19mm ( 3/4”)
39mm
EX-PM-051
19mm
6.35mm
8mm
6mm
5mm
3mm
1
Wooden panels must be prepared as shown to fix below and above the profile.
2
Profile must NOT be recessed from the front face of the panel.
Apply a suitable adhesive (not supplied) to channel on the top of the panel prior to inserting the profile on.
Insert the profile onto the panel by resting the Wood panel adapters onto the channel on the top edge of the panel and fix the profile to wall/substructure from the front using adequate hardware (not supplied).
18 ` 19 `EX-PM-051
3
Apply a suitable adhesive (not supplied) to the Wooden panel adapters prior to inserting the next panel.
Repeat step 3 & 4 to the last profile and finish by fixing the top panel using your preferred means.
20 ` 21 `EX-PM-051
Electrified EH profile for 19mm wooden panel (continuous installation)
22 ` 23 `
Router processing data of wooden panel
19mm ( 3/4”)
WARNING!
The electrical components of this product must be installed and inspected by qualified personnel.
Do not make alteration to this product, unless specifically authorised in installation guidelines.
Only CUBIC approved accessories are to be used with this product. For further assistance please contact us at [email protected].
39mm
EX-PM-051
1
Wooden panels must be prepared as shown to fix below and above the profile.
Red+
Black−
19mm
6.35mm
8mm
6mm
5mm
3mm
2
Apply a suitable adhesive (not supplied) to channel on the top of the panel prior to inserting the profile on.
Insert the profile onto the panel by resting the Wood panel adapters onto the channel on the top edge of the panel and fix the profile to wall/substructure from the front using adequate hardware (not supplied).
Profile must NOT be recessed from the front face of the panel.
24 ` 25 `EX-PM-051
Apply a suitable adhesive (not supplied) to the Wooden panel adapters prior to inserting the next panel.
Repeat step 3 & 4 to the last profile and finish by fixing the top panel using your preferred means.
3
26 ` 27 `EX-PM-051
012015EX-PM-051©CUBIC™
cubic.co
The material contained in this document may contain inaccuracies or typographical errors and may be subject to modification or updating by CUBIC™ without prior notice.