translation of the original operating manualmanual operation and for flat or round jet nozzles...
TRANSCRIPT
B_03154
c us
Electrostatic AirCoat Spray Gun for
Manual Operation and for Flat or
Round Jet Nozzles
Version 07/2014
Translation of the Original
Operating Manual
3
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Contents
1 ABOUT THIS OPERATING MANUAL 6
1.1 Preface 61.2 Warnings, Notices, and Symbols in this Operating Manual 61.3 Languages 71.4 Abbreviations 7
2 CORRECT USE 8
2.1 Device Type 82.2 Correct Use 82.3 Use in an Explosion Hazard Area 82.4 Safety Parameters 82.5 Processible Products 92.6 Reasonably Foreseeable Misuse 102.7 Residual Risks 10
3 IDENTIFICATION 11
3.1 Explosion Protection Identifi cation FM 113.2 Information for safe and correct operation 113.3 Permissible Device Combinations 12
4 GENERAL SAFETY INSTRUCTIONS 13
4.1 Safety Instructions for the Operator 134.1.1 Electrical Equipment 134.1.2 Staff Qualifi cations 134.1.3 Safe Work Environment 134.2 Safety Instructions for Staff 144.2.1 Safe Handling of WAGNER Spray Devices 144.2.2 Grounding the Device 154.2.3 Material Hoses 154.2.4 Cleaning 164.2.5 Handling Hazardous Liquids, Varnishes, and Paints 174.2.6 Touching Hot Surfaces 174.3 Correct Use 174.4 Safety Information on Discharges 184.5 Use in an Explosion Hazard Area 184.6 Notes to German Regulations and Guidelines 18
5 DESCRIPTION 19
5.1 Functional Description 195.1.1 Design of the Spray Gun (Basic Version) 195.1.2 Functioning of the Spray Gun 205.2 Scope of Delivery 225.3 Technical Data 235.4 Spray Process 245.4.1 AirCoat Round Jet Spray Process 245.4.2 AirCoat Flat Jet Spray Process 245.4.3 Electrostatic Eff ect 25
4
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Table of Contents
6 COMMISSIONING AND OPERATION 26
6.1 Training Assembly/Commissioning Staff 266.2 Storage Conditions 266.3 Installation Conditions 266.4 Installation and Connection 276.4.1 Typical Electrostatic Spraying System 276.4.2 Ventilation of the Spray Booth 286.4.3 Air Supply 296.4.4 Material Supply 296.4.5 Grounding 306.5 Preparation of Lacquer 336.5.1 Viscosity Conversion Table 336.6 Commissioning 346.6.1 General Rules for Manipulation of the Spray Gun 346.6.2 Preparation for Starting Up 34
7 OPERATION 37
7.1 Training the Operating Staff 377.2 Safety Instructions 377.3 Work 387.3.1 Filling with Working Product 387.3.2 Start-up for Spraying AirCoat 397.3.3 Flushing Out Clogged Round Jet Nozzles 407.3.4 Replacing Round Jet Nozzle's Nozzle Insert 407.3.5 Changing from AirCoat Round Jet to AirCoat Flat Jet 417.3.6 Replacing the AirCoat Flat Jet Nozzles 427.3.7 Cleaning of the Nozzle Parts 427.3.8 Eliminate Nozzle Clogging 427.3.9 Changing the Valve Housing 44
8 CLEANING AND MAINTENANCE 45
8.1 Cleaning 458.1.1 Cleaning Staff 458.1.2 Safety Instructions 458.1.3 Cleaning and Decommissioning 468.2 Maintenance 488.2.1 Maintenance Staff 488.2.2 Safety Instructions 488.3 Disassembly of the Spray Gun 498.3.1 Tools 498.3.2 Disassembly of the Spray Gun 508.4 Cleaning the Parts after Disassembly 538.5 Assembly of the Spray Gun 548.6 Function Test after Assembly of the Gun 598.6.1 Test of the High-Voltage 598.6.2 Air Test 608.6.3 Product Pressure Test 608.6.4 Test of Spray Pattern 618.7 High-Pressure Hoses 62
5
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Table of Contents
9 INSPECTIONS 63
9.1 Periodical Inspections 63
10 TROUBLESHOOTING AND RECTIFICATION 64
11 PRODUCT DISPOSAL 65
12 ACCESSORIES 66
12.1 Round Jet Nozzles 6612.1.1 ACR 5000 Round Jet Nozzle Cap 6612.1.2 AirCoat Round Jet Nozzle Inserts 6612.2 Flat Jet Nozzles 6612.2.1 ACF 5000 Air Caps (Flat Jet) 6612.2.2 ACF5000 AirCoat Flat Jet Nozzles 6712.3 Filter 6912.4 Reduction Fittings for High-Pressure Hoses 6912.5 Hoses and Electric Cables 7012.5.1 Standard Hose Sets and Components 7012.5.2 Hose Sets for Low-resistance Products 7212.5.3 Gun Cables and Gun Cable Extensions 7412.6 Miscellaneous 74
13 SPARE PARTS 77
13.1 How Can Spare Parts Be Ordered? 7713.2 GM 5000EAC Spare Parts List 7813.2.1 GM 5000EAC - Adapter Spare Parts List 8013.2.2 GM 5000EAC - Handle Spare Parts List 8213.3 Accessories Spare Parts Lists 8413.3.1 Flat Jet Nozzles Spare Parts List 8413.3.2 ACR 5000 Round Jet Nozzle Cap Spare Parts List 85
14 WARRANTY 86
14.1 Important Notes Regarding Product Liability 8614.2 Warranty Claim 86
6
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
1 ABOUT THIS OPERATING MANUAL
1.2 WARNINGS, NOTICES, AND SYMBOLS IN THIS OPERATING MANUAL
Warning instructions in this operating manual highlight particular dangers to users and to the device and state measures for avoiding the hazard. These warning instructions fall into the following categories:
Danger - immediate risk of danger.Non-observance will result in death or serious injury.
Warning - possible imminent danger.Non-observance may result in death or serious injury.
Caution - a possibly hazardous situation.Non-observance may result in minor injury.
Notice - a possibly hazardous situation.Non-observance may result in material damage.
Note - provides information about particular characteristics and how to proceed.
This notice warns you of a hazard!Possible consequences of not observing the warning instructions.The signal word indicates the hazard level.
The following are measures which can be taken to prevent the hazard and its consequences.
DANGER
This notice warns you of a hazard!Possible consequences of not observing the warning instructions.The signal word indicates the hazard level.
The following are measures which can be taken to prevent the hazard and its consequences.
WARNING
This notice warns you of a hazard!Possible consequences of not observing the warning instructions.The signal word indicates the hazard level.
The following are measures which can be taken to prevent the hazard and its consequences.
CAUTION
This notice warns you of a hazard!Possible consequences of not observing the warning instructions. The signal word indicates the hazard level.
The following are measures which can be taken to prevent the hazard and its consequences.
NOTICE
1.1 PREFACE
The operating manual contains information about safely operating, maintaining, cleaning and repairing the device.The operating manual is part of the device and must be available to operating and service staff .Operating and service staff should be instructed according to the safety instructions.The device may only be operated in compliance with this operating manual.This equipment can be dangerous if it is not operated according to the instructions in this operating manual.Electrostatic spray guns may only be operated by trained personnel.
7
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
1.3 LANGUAGES
The operating manual is available in the following languages:German English 2344500
1.4 ABBREVIATIONS
Order No. Order numberET Spare part
Marking in the spare parts listsLow R Low-resistance
PositionNumber of piecesWidth across fl ats
8
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
2 CORRECT USE
2.1 DEVICE TYPE
Electrostatic manual spray gun for manual coating of grounded work pieces
2.2 CORRECT USE
The GM 5000EAC electrostatic hand spray gun is suitable for spraying liquid products, particularly coating products, using the AirCoat method. Coating products containing solvents of explosion class II A may be used.
2.4 SAFETY PARAMETERS
The GM 5000EAC electrostatic manual spray gun is only suitable for spraying liquid products, particularly coating products.J. Wagner AG forbids any other use!The electrostatic manual spray gun may only be operated under the following conditions:
the operating staff have previously been trained on the basis of this operating manual,the safety regulations listed in this operating manual are observed,the operating, maintenance and repair information in this operating manual is observed,and the statutory requirements and accident prevention regulations standards in the country of use are observed.
The electrostatic manual spray gun may only be operated if all parameters are set and all measurements/safety checks are carried out correctly.
2.3 USE IN AN EXPLOSION HAZARD AREA
The GM 5000EAC electrostatic manual spray gun is suitable for coating electrically conductive objects with liquid coating products and can be used in potentially explosive areas. (See Chapter 3 "Identifi cation".)
9
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
2.5 PROCESSIBLE PRODUCTS
With the GM 5000EAC gun, paints can be applied which contain solvents of explosion class II A.The spray gun basic version is suitable for processing sprayed substances with an electrical resistance of > 150 kΩ (according to the WAGNER scale).Equipped with a special product hose for low-resistance sprayed substances (available as an accessory) you can also successfully process sprayed substances with an electrical resistance > 50 kΩ (according to the WAGNER scale).The transfer effi ciency is always dependant on the composition of the product being used, e.g. pigmentation or resin.
Conversion of Paint Resistance
There are paint resistance measuring devices available on the market that do not directly measure the specifi c paint resistance.Multiplying the result of the measurement with the device-specifi c cell constant (K), we obtain the specifi c resistance value of the product.
Example:
With Wagner’s paint resistance measuring device the cell constant is K =123.Measured value according to the WAGNER scaleSpecifi c resistance (RS)
Notice
Using sprayed substances with too low an electrical resistance, the application of electrostatics does not show any eff ect, i.e. there is no "paint wrap around" on the object to be sprayed.The suitability of the sprayed product with regard to the charging ability can be read from the indicators showing the actual values for the high-voltage (kV) and for the spray current (μA) the actual values are shown either on the VM 5000 control unit or on the spray gun.high kV value, low μA value = ok.low kV value, high μA value = excessive conductivity of the paint
-> no wrap-around
In the event of application problems, please contact your local WAGNER offi ce and the paint manufacturer.
10
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
2.6 REASONABLY FORESEEABLE MISUSE
Processing inadmissible coating productsUse of defective spare partsUse for foodstuff sUse in the pharmaceutical sector
2.7 RESIDUAL RISKS
Residual risks are risks which cannot be excluded even in the event of correct use.If necessary, warning and prohibition signs at the relevant points of risk indicate residual risks.
Residual risk Source Consequences Specifi c measures Lifecycle phase
Skin contact with solvent-based paints and cleaning agents
Handling of solvent-based paints and cleaning agents
Skin irritations, Wear protective clothing,
Operation,
allergies observe safety data sheets
maintenance,
disassembly
Solvent-based paint in air outside the defi ned working area
Painting outside the defi ned working area
Inhalation of substances hazardous to health
Observe work and operation instructions
Operation,
maintenance
11
C US
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
3 IDENTIFICATION
Safety instructions
Maximum surface temperature
Maximum surface temperature: 85 °C; 185 °FMaximum permissible product temperature: 50 °C; 122 °FPermissible ambient temperature: 0 to +40 °C; +32 to +104 °F
Safe handling of WAGNER spray devices
Mechanical sparks can form if the device comes into contact with metal.In an explosive atmosphere:
Do not knock or push the unit against steel or rusty iron. Do not drop the spray gun. Only use tools that are made of a permitted material.
3.1 EXPLOSION PROTECTION IDENTIFICATION FM
For Electrostatic Finishing Applications using Class I, Group D, Spray Material
In accordance with 2316160
This device has been manufactured and tested by FM, according to the FM (Factory Mutual) standard "Class Number 7260" (Approval Standard for Electrostatic Finishing Equipment). All tested combinations of devices including accessories are given in the FM Control Document with part number 2316160.
3.2 INFORMATION FOR SAFE AND CORRECT OPERATION
Ignition temperature of the coating product
Ensure that the ignition temperature of the coating material is above the maximum surface temperature.
12
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
3.3 PERMISSIBLE DEVICE COMBINATIONS
The GM 5000EAC manual spray gun may only be connected to the control units listed below:
VM 500 control unitVM 5000 control unit
Incorrect use!
Risk of injury and equipment damage.
Connect the GM 5000EAC manual spray gun only to original Wagner control units.
WARNING
Surface spraying, electrostatics
Never spray device parts using electrostatic equipment (electrostatic spray gun!).
Medium supporting atomizing
To atomize the product, use only weakly oxidizing gases, e.g. air.
Cleaning
If there are deposits on the surfaces, the device may form electrostatic charges. Flames or sparks can form during discharge.
Remove deposits from the surfaces to maintain conductivity. Only use a damp cloth to clean the device.
13
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
4 GENERAL SAFETY INSTRUCTIONS
4.1 SAFETY INSTRUCTIONS FOR THE OPERATOR
4.1.1 ELECTRICAL EQUIPMENT
4.1.2 STAFF QUALIFICATIONS
4.1.3 SAFE WORK ENVIRONMENT
Keep this operating manual at hand near the unit at all times. Always follow local regulations concerning occupational safety and accident prevention.
Electrical devices and equipment To be provided in accordance with the local safety requirements with regard to the
operating mode and ambient infl uences. May only be maintained by skilled electricians or under their supervision. Must be operated in accordance with the safety regulations and electrotechnical regulations. Must be repaired immediately in the event of problems. Must be decommissioned if they pose a hazard. Must be de-energized before work is commenced on active parts. Inform staff about
planned work. Observe electrical safety regulations.
Ensure that the device is operated and repaired only by trained persons.
Ensure that the fl oor in the working area is static dissipative in accordance with EN 61340-4-1 (resistance must not exceed 100 Mohm).
Ensure that all persons within the working area wear static dissipative shoes. Footwear must comply with EN 20344. The measured insulation resistance must not exceed100 Mohm.
Ensure that during spraying, persons wear static dissipative gloves. The grounding takes place via the spray gun handle.
If protective clothing is worn, including gloves, it has to comply with EN 1149-5.The measured insulation resistance must not exceed 100 Mohm.
Paint mist extraction systems must be fi tted on site according to local regulations. Ensure that the following components of a safe working environment are available:
– Product/air hoses adapted to the working pressure. – Personal safety equipment (breathing and skin protection).
Ensure that there are no ignition sources such as naked fl ames, sparks, glowing wires, or hot surfaces in the vicinity. Do not smoke.
14
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
4.2 SAFETY INSTRUCTIONS FOR STAFF
Always follow the information in this manual, particularly the general safety instructions and the warning instructions.
Always follow local regulations concerning occupational safety and accident prevention.
4.2.1 SAFE HANDLING OF WAGNER SPRAY DEVICES
The spray jet is under pressure and can cause dangerous injuries.Avoid injection of paint or cleaning agents:
Never point the spray gun at people. Never reach into the spray jet. Before all work on the device, in the event of work interruptions and functional faults:
– Switch off the energy/compressed air supply. – Relieve the pressure from the spray gun and device. – Secure the spray gun against actuation. – In the event of functional faults: remedy the fault as described in the "Troubleshooting"
chapter. The liquid ejection devices are to be checked for safe working conditions by an expert
(e.g. Wagner Service Technician) as often as necessary or at least every 12 months, in accordance with the guidelines for liquid ejection devices (ZH 1/406 and BGR 500 Part 2 Chapter 2.36).
– For shut down devices, the examination can be suspended until the next commissioning. Carry out the work steps as described in the "Pressure Relief/Work Interruptions" chapter:
– if pressure relief is required. – if the spraying work is interrupted or stopped. – before the device is cleaned on the outside, checked, or serviced. – before the spray nozzle is installed or cleaned.In the event of skin injuries caused by paint or cleaning agents:
Note down the paint or cleaning agent that you have been using. Consult a doctor immediately.
Avoid danger of injury through recoil forces: Ensure that you have firm footing when operating the spray gun. Only hold the spray gun briefl y in a position.
15
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
4.2.2 GROUNDING THE DEVICE
In order to avoid electrostatic charging of the device, the device must be grounded.Friction, fl owing liquids, and air or electrostatic coating processes create charges. Flames or sparks can form during discharge.
Ensure that the device is grounded at all times. Ground the work pieces to be coated. Ensure that all persons inside the working area are grounded, e.g. that they are wearing
static dissipative shoes. Wear dissipative gloves when spraying. The grounding takes place via the spray gun handle. Grounding of the coating product supply (coating product tank, pump, etc.) is mandatory.
Ensure that the hose material is chemically resistant to the sprayed products. Ensure that the product hose is suitable for the pressure generated in the device. Ensure that the following information can be seen on the high-pressure hose:
– Manufacturer – Permissible operating overpressure – Date of manufacture
Make sure that the hoses are laid only in suitable places. In no case, should hoses be laid in the following places:
– in high-traffic areas, – on sharp edges, – on moving parts, or – on hot surfaces
Make sure that the hoses are never used to pull or move the equipment. The electrical resistance of the complete high-pressure hose must be less than 1 Mohm.
4.2.3 MATERIAL HOSES
16
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
4.2.4 CLEANING
De-energize the device electrically. Disconnect the pneumatic supply line. Relieve the pressure from the device. Ensure that the fl ash point of the cleaning agent is at least 15 K above the ambient
temperature or that cleaning is undertaken at a cleaning station with technical ventilation. To clean, use cloths and brushes moistened with solvent. Abrasive agents or objects
must not be used. Ensure that the spray gun is not damaged in any way while cleaning. Parts of the spray gun must not be sprayed with or immersed into cleaning agent. Preferably, non-combustible cleaning agents should be used. The choice of the appropriate cleaning agent depends on which parts of the spray
gun have to be cleaned and which product has to be removed. When cleaning the spray gun only use non-polar cleaning agents to prevent conductive residues on the surface of the spray gun. Should it however, be necessary to use a polar cleaning agent, all residues of this cleaning agent have to be removed by using a non-conductive and non-polar cleaning agent, once the cleaning is fi nished.
Ensure that no electrical component is cleaned with nor even immersed into solvent.
An explosive gas/air mixture forms in closed tanks.
When cleaning devices with solvents, never spray into a closed tank. Only use electrically conductive tanks for cleaning liquids. The tanks must be grounded.
17
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
4.2.5 HANDLING HAZARDOUS LIQUIDS, VARNISHES, AND PAINTS
When preparing or working with paint and when cleaning the device, follow the working instructions of the manufacturer of the paints, solvents, and cleaning agents being used.
Take the specifi ed protective measures. In particular, wear safety goggles, protective clothing and gloves, as well as skin protection cream if necessary.
Use a mask or a breathing apparatus if necessary. For suffi cient health and environmental safety: operate the device in a spray booth or
on a spraying wall with the ventilation (extraction) switched on. Wear suitable protective clothing when working with hot products.
4.2.6 TOUCHING HOT SURFACES
Only touch hot surfaces if you are wearing protective gloves. When operating the device with a coating product with a temperature of > 43 °C;
109.4 °F: - Identify the device with a warning label "Warning - hot surface".Order No.
9998910 Instruction label9998911 Protection stickerNote: Order the two stickers together.
4.3 CORRECT USE
WAGNER accepts no liability for any damage arising from incorrect use. Use the device only to work with the products recommended by WAGNER. Only operate the device as a whole. Do not deactivate safety fi xtures. Use only WAGNER original spare parts and accessories.
18
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
4.4 SAFETY INFORMATION ON DISCHARGES
The plastic parts of the spray gun are charged electrostatically by the high-voltage fi eld of the spray gun. In case of contact with plastic parts harmless discharges (brush discharges) may occur. They are completely non-hazardous for human health.When keeping a distance of 4 to 10 mm; 0.15 to 0.4 inch between spray gun and object to be sprayed, the corona discharge at the end of the electrode is visible during darkness.
4.5 USE IN AN EXPLOSION HAZARD AREA
In explosion hazard areas only use approved explosion-proof electrical devices.
4.6 NOTES TO GERMAN REGULATIONS AND GUIDELINES
Electrical devices and equipmentPart 2, Chapter 2.36 Working with Liquid Ejection DevicesPart 2, Chapter 2.29 Working with Coating ProductsExplosion protection rulesAvoiding ignition risksEquipment for cleaning work pieces with solventsGuidelines for liquid ejection devicesPainting rooms and equipmentElectrostatic coatingPlant Safety Ordinance
Note: All titles can be ordered from Heymanns Publishing House in Cologne, or they can be found on the Internet.
19
B_03558S
B_03156
7
13
14
6
5 11
1615
24
20
3
1
9
10
8
1918
17
21
22
12
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
5 DESCRIPTION
5.1 FUNCTIONAL DESCRIPTION
Description
1 Suspension hook2 Display (spray current and recipe)3 Display standby4 Operating button
(standby and recipe change)5 Protection against contact with union nut6 Air cap for fl at jet nozzle
(see accessories in Chapter 12.2.1)7 Flat jet nozzle ACF 5000
(see accessories in Chapter 12.2.2)8 Adapter9 Cover
10 Handle11 Trigger lock
Description
12 Trigger lever13 Round jet nozzle adapter
(see accessories in Chapter 12.1.1)14 Round jet nozzle insert
(see accessories in Chapter 12.1.2)15 Sealing plug16 Air adjustment17 Electric cable connection18 Atomizing air connection19 Product connection20 Filter housing with fi lter21 Type plate left22 Type plate right
Note:
The nozzle parts (pos 6; 7; 13 and 14) do not belong to the basic equipment of the spray gun. The diff erent versions can be found in Chapter 12 "Accessories".
Note:
The gun type (T) on the type plate (21) and the serial number (S) on the underside of the handle.
5.1.1 DESIGN OF THE SPRAY GUN (BASIC VERSION)
20
R1 R3R2
B_03182
2
4
3
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
5.1.2 FUNCTIONING OF THE SPRAY GUN
When the spray gun is connected to the control unit and the control unit is switched on, the pre-defi ned recipe (R1, R2 or R3) is shown on the gun display (2) as follows.Recipe 1 -> Recipe 2 -> Recipe 3 ->
Recipe change R1 -> R2 -> R3 -> R1.Press the operating button (4) and keep the button pressed of at least 2 seconds, then it is advanced by 1 recipe.
Display (2) -> = recipe values changed temporarily:The stored recipe values of the previously selected recipe number are re-loaded from memory by pressing the operating button (4) for 2 seconds.
During spraying (trigger lever pressed), the status is shown in the display (2) by LEDs.
LED display Description
LEDs 1 - 3 light up green The spray gun is working in an optimal high-voltage spray current range
one or both right-hand LEDs light up orange
spray current too high
Possible causes:
(Warning display: You can continue working without any limitations.)
Spray gun too close to the work piece
Contamination of the spray gun
Paint conductivity too high
21
12
3
4
B_03157
R1 R3R2
E
B_03262
16
4
23
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Distance Description
1 AirCoat air opens.2 AirCoat air opened and electrostatic
(high-voltage) activated.Display (2) for "spray current" on the spray gun
to activated.3 AirCoat air opened and electrostatic
(high-voltage) activated and product valve opened.4 Overall way of trigger
An increase in the force needed to pull the trigger back will be perceived at the position where the product valve opens.For spraying without high-voltage, the high-voltage can be switched off using the operating button (4). Press the operating button (4) briefl y: High-voltage is switched off . The standby display (3) illuminates.In the event of a malfunction the spray gun switches to "standby" operating mode and the display (3) blinks.The width of the spray jet can be adjusted using the air adjustment (16) (only for fl at-jet method).
The trigger can be used to activate, one after the other, the various functions of the spray gun.
22
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Stk Order No. Description
1 2344473 GM 5000EAC spray gunWithout control unit, product and air hose, electric cable, air cap and nozzle.
Each gun includes as standard equipment:Order No. Description
1 2309368 Assembly tool valve needle1 2325263 Assembly tool clamping screw1 2319653 Protection gloves against spray mist1 2316160 FM Control Document GM 5000E1 see Chapter 1.3 Operating manual in local language
The spray gun basic version can be set according to requirement and the desired accessories by means of the spray gun confi guration.
The delivery note shows the exact scope of delivery.
5.2 SCOPE OF DELIVERY
23
C
A
B_03155
B
C
A
B_03193
B
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
5.3 TECHNICAL DATA
GM 5000EAC Fwith fl at jet nozzle
mm inchA 280 11.02B 46 1.81C 264 10.39
GM 5000EAC Rwith round jet nozzle
mm inchA 264 10.39B 46 1.81C 264 10.39
Dimensions
Maximum air pressure 0.8 MPa; 8 bar; 116 psiMaximum product pressure 25 MPa; 250 bar; 3,626 psiFluid inlet NPSM 1/4"-18Air connection G 1/4" AInput voltage maximum 20 VppInput current maximum 1.0 A ACOutput voltage maximum 70 kV DCOutput current maximum 100 μA DCPolarity negativeWeight (without hose set) 710g
(including union nut, nozzle, air cap and edge fi lterOperating temperature range 0 °C to 40 °C
32 °F to 104 °FMaximum product temperature 50°C
122 °FSound level at 0.3 MPa; 3 bar; 43.5 psi air pressure and 11 MPa; 110 bar; 1,549 psi product pressure.
73 dB(A) *
* A-rated sound pressure level measured at 1 m distance, LpA1m, in accordance with DIN EN 14462: 2005.
24
B_00020
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
5.4 SPRAY PROCESS
AirCoat air
Multi-channel swirl nozzle
Spray jet
Nozzle nut
Spray productAirCoat air
Advantages
Large application volumeLow fogging tendencyGood fi nishHigh viscosity paints can easily be appliedHigh endurance of the nozzlesJet width adjustment
5.4.2 AIRCOAT FLAT JET SPRAY PROCESS
Shaping air
Aircap
Variable spray jet width
Atomizing air
Advantages
Large application volumeLow fogging tendencyGood fi nishHigh viscosity paints can easily be appliedHigh endurance of the AC-nozzlesJet width adjustment
In the AirCoat process, the spray product is atomized under a pressure of 3-15 MPa; 30-150 bar; 435-2,176 psi. With the help of an air pressure of 0-0.25 MPa; 0-2.5 bar; 0-36 psi, a soft, spray jet is produced. The spray jet diameter can be adjusted by turning the nozzle nut.
5.4.1 AIRCOAT ROUND JET SPRAY PROCESS
In the AirCoat process, the spray product is atomized under a pressure of 3-15 MPa; 30-150 bar; 435-2,176 psi. With the help of the AirCoat air, with a pressure of 0-0.25 MPa; 0-2.5 bar; 0-36 psi, a soft, fl at spray jet is produced which largely eliminates the problem of overlapping in the peripheral zones. With shaping air, there is the possibility of reducing the width of the spray jet.
25
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
ElectrodePaint particle
Object to be sprayedgrounded
The spray gun produces an electrostatic fi eld by means of the high-voltage electrode. As a result, the paint particles atomized by the spray gun are carried to the grounded work piece by kinetic and electrostatic energy where they adhere fi nely dispersed to the object to be sprayed.
5.4.3 ELECTROSTATIC EFFECT
Advantages
Very high application eff ectivenessLow over sprayCoating of entire circumferences due to the electrostatic eff ectSavings in working time
26
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
6 COMMISSIONING AND OPERATION
6.1 TRAINING ASSEMBLY/COMMISSIONING STAFF
Incorrect installation/operation!
Risk of injury and equipment damage.
The commissioning staff must have the technical skills to safely undertake commissioning.
When commissioning and for all work, read and follow the operating manual and safety regulations for the additionally required system components.
WARNING
6.2 STORAGE CONDITIONS
Until the point of assembly, the manual spray gun must be stored in a dry location, free from vibrations and with a minimum of dust. The manual spray gun must be stored in closed rooms.The air temperature at the storage location must be between -20 - +60 °C; -4 - +140 °F.The relative air humidity at the storage location must be between 10 and 95 % (without condensation).
6.3 INSTALLATION CONDITIONS
The air temperature at the installation site must be between 0 - 40 °C; 32 - 132 °F.The relative air humidity at the installation site must be between 10 and 95 %(without condensation).
27
EXT
100
80
60
40
20
μA
80
60
40
20
10
kV
R3
R1
R2
VM 5000
7
6
8
45
9
17
1
21615
14
21
12
11
10
B_03158
18 19
20
3
3
13
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
6.4 INSTALLATION AND CONNECTION
Description
1 GM 5000EACF spray gun2 Gun cable3 Grounding cable4 Pneumatic pump5 Trolley6 Pressure regulator + air
fi lter7 Product suction system8 Return hose9 High-pressure fi lter
10 Compressed air connection
Description
11 Stop valve12 Air pressure regulator13 VM 5000 control unit14 Protective hose15 Air hose16 Product hose17 Return valve18 Tank for return fl ow
Description
19 Paint tank20 Tank, cleaning agent21 Power cable
6.4.1 TYPICAL ELECTROSTATIC SPRAYING SYSTEM
28
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
6.4.2 VENTILATION OF THE SPRAY BOOTH
The GM 5000EAC spray gun must be used as part of a spraying system (Spraypack). The system shown in fi gure B_03158 is only one example of an electrostatic spraying system. Your WAGNER distributor would be happy to assist you in creating a spraying system solution that meets your individual needs. You must familiarize yourself with the operating instructions and the safety regulations of all additional system components before starting commissioning.
Incorrect installation/operation!
Risk of injury and equipment damage.
When commissioning and for all work, read and follow the operating manual and safety regulations for the additionally required system components.
WARNING
Toxic and/or fl ammable vapor mixtures!
Risk of poisoning and burns.
Operate the device in a spray booth approved for the working products.
-or- Operate the device on an appropriate spraying wall with the
ventilation (extraction) switched on. Observe national and local regulations for the outgoing air
speed.
WARNING
The electrostatic hand spraying equipment is for use only in spray areas which correspond with standard EN 12215.The electrostatic hand spraying equipment has to be locked to the technical ventilation so that the coating product supply and the high-voltage are not eff ective as long as the technical ventilation is not operated with the minimum exhaust air volume fl ow or a larger exhaust air volume fl ow.Ensure that the excess coating product (overspray) will be collected up safely.
29
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
6.4.4 MATERIAL SUPPLY
Impurities in the spraying system!
Spray gun blockage, products harden in the spraying system.
Flush the spray gun and paint supply with a suitable cleaning agent.
NOTICE
6.4.3 AIR SUPPLY
The use of an air fi lter with the air regulator (6) ensures that only dry, clean atomizing air gets into the spray gun. Dirt and moisture in the atomizing air worsens the spraying quality and spraying pattern.
Bursting hose, bursting threaded joints!
Danger to life from injection of product.
Ensure that the hose material is chemically resistant to the sprayed products.
Ensure that the spray gun, threaded joints, and product hose between the device and the spray gun are suitable for the pressure generated in the device.
Ensure that the following information can be seen on the high-pressure hose:
- Manufacturer - Permissible operating pressure - Date of manufacture
DANGER
Hose connections
Risk of injury and equipment damage.
Do not exchange hose connections of product hose and air hose.
WARNING
30
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Perfect grounding of all conductive parts such as fl oors, walls, roofs is important for optimum coating and safety. Barriers, work pieces, transport devices, coating product tank, coating product supply or construction parts in the spray area with exception of the high-voltage parts during normal operation.Parts of the booth must be grounded in accordance with EN 12215.
A poorly grounded work piece causes:
very bad wrap around,uneven coating,back spraying to the spray gun, i.e. contamination.
Prerequisites for perfect grounding and coating are:
Clean work piece suspension.Grounding of spray booth, conveyor system and suspension on the building side in accordance with the operating instruction or the manufacturer's information.Grounding of all conductive parts within the working area.The grounding resistance of the work piece may not exceed 1 MΩ (Megohm).Note:
Resistance to ground measured at 500 V or 1,000 V.Connect the control unit to the system ground.
6.4.5 GROUNDING
Discharge of electrostatically charged components in atmospheres
containing solvents!
Explosion hazard from electrostatic sparks or fl ames.
Ground all device components. Ground the work pieces to be coated.
WARNING
Heavy paint mist if grounding is insuffi cient!
Danger of poisoning.Insuffi cient paint application quality.
Ground all device components. Ground the work pieces to be coated.
WARNING
31
B_03234
R max < 1 MΩ
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Minimum cable cross-section
Control unitPumpPaint tankConveyorBoothSpraying stand
Control unit
Grounding cable
Spraying stand
Floor static dissipative
Work piece
Pump or pressure tank
Paint tank or tank for return fl ow
Grounding schema (example):
Note for the sprayer:
Safety shoes and gloves, if used, must be static dissipative.
Conveyor
Power cable
32
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
33
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
6.5 PREPARATION OF LACQUER
6.5.1 VISCOSITY CONVERSION TABLE
The viscosity of the lacquers is of great importance. The best spraying results are obtained with values between 25 and 40 DIN-s (measured in immersion fl ow cup DIN 4 mm; 0.16 inch). Processing of up to 60 DIN-s is generally possible without problem, if high coating thicknesses are required.
With the Wagner AirCoat fl at jet spraying process, the diff erent viscosities of the lacquer are optimally covered by two air cap types. These can be found in "Accessories".
In the case of application problems contact the paint producer.
10 10 0.1 5 1615 15 0.15 8 1720 20 0.2 10 1825 25 0.25 14 12 1930 30 0.3 15 14 2040 40 0.4 17 18 2250 50 0.5 19 22 2460 60 0.6 21 26 2770 70 0.7 23 28 3080 80 0.8 25 31 3490 90 0.9 28 32 37
100 100 1 30 34 41120 120 1.2 33 41 49140 140 1.4 37 45 58160 160 1.6 43 50 66180 180 1.8 46 54 74200 200 2 49 58 82220 220 2.2 52 62240 240 2.4 56 65260 260 2.6 62 68280 280 2.8 65 70300 300 3 70 74320 320 3.2340 340 3.4360 360 3.6 80380 380 3.8400 400 4 90
34
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Observe safety instructions in Chapter 4.
The following points should be noted before commissioning
Grounding see Chapter 6.4.5. Make sure that all other conductive parts within the work area are grounded.Connect the product hose to spray gun and product pump.Check that all product-conveying connections are correctly connectedConnect air hose to spray gun and to supply of oil-free dry air, approx. 0.25 MPa; 2.5 bar; 36 psi. Compressed air quality class 3.5.2 according to ISO 8573.1.Check that all air-conveying connections are correctly connected.Connect the electric cable to the spray gun and to the VM 5000 or VM 500 control unit.Visually check the permissible pressures for all the system components.Check the level of the separating agent in the Wagner pneumatic pump and fi ll the separating agent up if necessary.
6.6 COMMISSIONING
6.6.1 GENERAL RULES FOR MANIPULATION OF THE SPRAY GUN
High-voltage fi eld!
Danger to life from malfunction of heart pacemakers.
Make sure that persons with pace makers: Do not work with the electrostatic spray gun. Stay outside the area of the electrostatic spray gun/work piece.
DANGER
Unintentional putting into operation!
Risk of injury.
Before any work on the device, in the event of work interruptions and malfunctions:
Switch off the energy/compressed air supply. Relieve the pressure from the spray gun and unit. Secure the spray gun against actuation. In the event of functional faults: remedy the fault as described
in the "Troubleshooting" chapter.
WARNING
6.6.2 PREPARATION FOR STARTING UP
35
B_03691
84
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Attention: gun cable to control unit
Secure the cover sleeve with the warning sign by means of the screw (84) on the connector.
GM 5000E gun cable
Provide product tank, tanks for fl ushing agent and an empty tank for return.Connect the system with a secured gun to the air and power supply.A basic fl ushing of system must be carried out before commissioning. Make sure that no nozzle is inserted into the gun.
Sparks form when the plug is removed!
Explosion hazard.
When using the spray gun in explosion hazard areas: The cable connection on the gun and the connection to any
cable extensions may not be disconnected or connected in this area.
WARNING
36
B_03690
84 84
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
GM 5000E gun cableExtension cable to the control unit
Attention: guns with electric extension cable
Secure the cover sleeves with the warning sign by means of the screws (84) on the connectors.
Note:
In order to prevent power losses, keep the cable length as short as possible. The maximum power is available with the standard cable length of 10 m.An extension to a total length of up to 40 m will cause a power loss of up to 10%. The gun cable can be extended to a total length of 80 m, however, a power loss of up to 30 % will be caused.
37
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
7 OPERATION
7.1 TRAINING THE OPERATING STAFF
7.2 SAFETY INSTRUCTIONS
Incorrect operation!
Risk of injury and equipment damage.
The operating staff must be qualifi ed to operate the entire system.
Before work commences, the operating staff must receive appropriate training.
WARNING
Incorrect operation!
Risk of injury and equipment damage.
If contact with solvent-based paints or cleaning agents causes skin irritation, appropriate precautionary measures must be taken, e.g. wearing protective clothing.
The footwear worn by operating staff must comply withEN ISO 20344. The measured insulation resistance must not exceed 100 MΩ.
The protective clothing, including gloves, must comply with EN ISO 1149-5. The measured insulation resistance must not exceed 100 MΩ.
WARNING
Discharge of electrostatically charged components in atmospheres
containing solvents!
Explosion hazard from electrostatic spark-over.
Use gun only with fi tted nozzle, air cap and union nut. Tighten the union nut, especially with nozzle in the cleaning
position.
WARNING
38
EXT
100
80
60
40
20
μA
80
60
40
20
10
kV
R3
R1
R2
VM 5000
7
6
8
45
9
17
1
21615
14
21
12
11
10
B_03158
18 19
20
3
3
13
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
7.3 WORK
1. Place an empty tank (18) under the return tube (8) (see picture B_03158).2. Place suction hose (7) in the tank with working product (19).
Note:
If the pump is equipped with a rigid suction system, it should only be dipped in into the working product up to the middle of the inlet housing at the maximum!
3. Adjust the pressure regulator (12) to approx. 0.05 MPa; 0.5 bar; 7.25 psi.4. Open return valve (17).5. Slowly open the ball valve (11).6. Adjust the air pressure on the pressure regulator (12) so that the pump runs smoothly.7. Close ball valve (11) as soon as pure working product starts coming from the return
tube (8).
7.3.1 FILLING WITH WORKING PRODUCT
39
B_03192
B_03159
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
8. Close return valve (17).9. Point the gun, without nozzle, into tank (18) and open it.
10. Slowly open the ball valve (11).11. Close ball valve (11) as soon as pure working product starts coming from the gun.12. When there is no pressure remaining in the system, close the gun.13. Secure the gun.14. Dispose of the contents of the tank (18) according to the local regulations.
1. Secure gun and insert the desired nozzle into the gun.2. Set pump (4) to about 8 Mpa; 80 bar; 1,160 psi operating pressure and start up
control unit (13).3. Spraying (pull trigger).4. Adjust the spray pressure at the paint pump according to the nozzle and object
being sprayed5. Now open AirCoat air (6), approx. 0.01-0.25 MPa; 1-2.5 bar; 14,5-36 psi, and adjust for
the optimal atomization.
For round-jet method:
6. By turning the nozzle nut, the atomizing air jet can additionally be adjusted.Notes:
Do not turn the nozzle nut until it is fl ush with the nozzle body. There must be play for the atomizing air between the nozzle nut and the nozzle body.The air adjustment at the back of the gun does not aff ect the spray pattern in this process.
For fl at-jet method:
7. Change the width of the spray jet by turning the air adjustment on the back of the spray gun or by appropriate selection of the nozzle.
7.3.2 START-UP FOR SPRAYING AIRCOAT
40
1/2
1
2B_03160
B_031611
2
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
7.3.3 FLUSHING OUT CLOGGED ROUND JET NOZZLES
1. Use nozzle spanner (2) to loosen nozzle insert (1) by a half turn.
2. Remove the nozzle spanner and briefl y actuate trigger.
3. After fl ushing the nozzle, re-tighten the nozzle insert.
7.3.4 REPLACING ROUND JET NOZZLE'S NOZZLE INSERT
Exploding gas / air mixture!
Danger to life from fl ying parts and burns.
Never spray into a closed tank. Ground the tank.
DANGER
1. Remove nozzle insert (1) using nozzle spanner (2).2. Assembling new nozzle insert.
41
B_03162
1
2
34
5
67
8
109
Y
11
1
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
7.3.5 CHANGING FROM AIRCOAT ROUND JET TO AIRCOAT FLAT JET
1. Flush the spray gun (1) out thoroughly with cleaning agent.
2. Relieve the pressure of gun and device.3. Secure the spray gun (1) using the trigger lock.4. Unscrew round jet nozzle cap (2) incl. nozzle insert (3).5. Unscrew nozzle insert (3) using nozzle spanner (4).6. Unscrew nozzle nut (5) and remove nozzle screw
connection (7) and sealing fi tting (8) out off the nozzle body (6) and clean all parts thoroughly.
7. Insert desired ACF 5000 nozzle (11) into the valve housing.
8. Put the air cap (10) on the nozzle (11) and pay attention to the position of the guide surfaces.
9. Screw union nut with attached nozzle guard (9) to the gun body and make sure that the air cap horns lie in the designated recess (Y).
10. Before tightening with the air cap horns (Y), set the desired jet level and then tighten the union nut to stop by hand.
42
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
7.3.6 REPLACING THE AIRCOAT FLAT JET NOZZLES
1. Switch off control unit.2. Relieve pressure from the gun (1) and from the device!3. Secure the spray gun (1) using the trigger lock.4. Unscrew union nut (12) and remove air cap (10).5. Remove ACF5000 AirCoat nozzle (11) and treat it with cleaning agent until all traces
of paint have been removed.
The ACF5000 AirCoat nozzles (11), the nozzle inserts (3) and the nozzle screw connection (7) can be placed in a cleaning solvent recommended by the lacquer manufacturer.
All other nozzle parts may not be put into cleaning solvent.Clean these parts with a cleaning solvent recommended by the lacquer manufacturer and dry with a cloth or blow gun.
1. Switch off control unit.2. Relieve the pressure of gun and device.3. Secure the spray gun (1) using the trigger lock (14).4. Unscrew complete union nut (12) with air cap (10) and ACF5000 nozzle (11).5. Remove air cap (10).6. Push ACF 5000 nozzle (11) out of air cap (10) by hand, reverse it and put it into the air
cap (10) with the nozzle tip towards the rear.Pay attention to the position of the guide surfaces (X).
7. Insert air cap (10) with integrated ACF5000 nozzle (11) into the union nut (9).Make sure that the air cap horns (Y) lie in the recess of the nozzle guard.
Defective AirCoat nozzle!
Insuffi cient paint application quality.
Do not use sharp-edged objects to treat carbide on the AirCoat nozzle.
NOTICE
6. Insert new ACF5000 nozzle (11) into the valve housing.7. Put the air cap (10) on the nozzle (11) and pay attention to the position of the guide
surfaces.8. Screw union nut with attached nozzle guard (9) to the gun body and make sure that
the air cap horns lie in the designated recess (Y).9. Before tightening with the air cap horns (Y), set the desired jet level and then tighten
the union nut to stop by hand.
7.3.7 CLEANING OF THE NOZZLE PARTS
7.3.8 ELIMINATE NOZZLE CLOGGING
43
B_03211
10
11
X
Y
1
14
12
12
Y
9
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
8. Screw preassembled union nut (12) to gun (1) and tighten by hand.9. Switch the product pressure back on.
10. Turn the trigger lock (14) to the spraying position and briefl y pull the trigger.11. When the blockage has been fl ushed out, secure the gun with the trigger lock.12. Relieve the pressure of gun and device.13. Unscrew union nut (12).14. Remove air cap (10) and push ACF5000 nozzle (11) out of the air cap by hand.
Clean ACF5000 nozzle and insert it in the spraying position into the valve housing.15. Put the air cap (10) on the nozzle (11) and pay attention to the position of the guide
surfaces (X).16. Screw union nut with attached nozzle guard (9) to the gun body and make sure that
the air cap horns lie in the designated recess (Y).17. Before tightening with the air cap horns (Y), set the desired jet level and then tighten
the union nut to stop by hand.18. Switch the product pressure and the air pressure back on.19. Switch on the control unit.
ACF5000 nozzle in cleaning position
ACF5000 nozzle in spray position
44
B_03847
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
7.3.9 CHANGING THE VALVE HOUSING
Changing the valve housing!
Equipment damage.
Activate the spray gun trigger when changing the valve housing.
NOTICE
To prevent damage to the gun (valve seat rubs on the valve needle, valve needle may loosen), activate the spray gun trigger when changing the valve housing.
45
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
8 CLEANING AND MAINTENANCE
Cleaning work should be undertaken regularly and carefully by qualifi ed and trained staff . They should be informed of specifi c hazards during their training.
The following hazards may arise during cleaning work:Health hazard from inhaling solvent vaporsUse of unsuitable cleaning tools and aids
8.1 CLEANING
8.1.2 SAFETY INSTRUCTIONS
8.1.1 CLEANING STAFF
Explosive powder/air mixes!
Danger to life and equipment damage.
Before starting cleaning or other manual work, the high-voltage must be shut down and locked to prevent it from being switched back on!
The spray gun must be separated from the high-voltage supply before any cleaning work is started!
Use only electrically conductive tanks for cleaning liquids! Ground the tank!
Preference should be given to non-fl ammable cleaning fl uids. Only cleaning agents of explosion class IIA should be used
(maximum ignition energy 0.24 mJ). The cleaning agent's fl ash point must be at least 15 K above the
ambient temperature. Ensure that no electric component is cleaned with or immersed
into solvent.
DANGER
46
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
The spray gun and the unit must be cleaned daily. The cleaning agents used for cleaning must correspond with the working product.
Cleaning of the nozzle parts -> Chapter 7.3.7Eliminating Nozzle Clogging -> Chapter 7.3.8
8.1.3 CLEANING AND DECOMMISSIONING
Flushing agent in the air duct!
Functional faults caused by swollen seals.
Never immerse the spray gun in cleaning agent.
NOTICE
Incorrect maintenance/repair!
Risk of injury and equipment damage.
Have repairs and part replacements be carried out only by specially trained staff or a WAGNER service center.
Before all work on the device and in the event of work interruptions:
- Switch off the energy/compressed air supply. - Relieve the pressure from the spray gun and device. - Secure the spray gun against actuation.
Observe the operating instructions for any work.
WARNING
47
B_03453
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Gun fl ushing
1. Switch off control unit.2. Ensure that the product pressure is relieved and shut off the air supply to the gun.3. Connect the cleaning agent supply.
With round jet nozzle fi tted:
4. By means of nozzle spanner, loosen nozzle insert by 1/2 turn.5. Actuate the trigger. Flush the gun thoroughly.6. Relieve the pressure from gun and unit!7. Re-tighten the nozzle insert.8. Clean the spray gun body with a cleaning agent recommended by the manufacturer
and dry with a cloth or blow gun.With fl at jet nozzle fi tted:
4. Dismount AirCoat nozzle and clean separately (see Chapter 7.3.7).5. Actuate the trigger. Flush the gun through thoroughly.6. Relieve the pressure from gun and unit!7. Clean the spray gun body with a cleaning agent recommended by the lacquer
manufacturer and dry with a cloth or blow gun.
Exploding gas / air mixture!
Danger to life from fl ying parts and burns.
Never spray into a closed tank. Ground the tank.
DANGER
NOTICEFlushing agent in the air duct!
Functional faults caused by swollen seals.Discharge current to ground -> no high-voltage
Always point the spray gun down when cleaning. Ensure that neither paint nor cleaning agent enters the air duct. When taking a break from work or when stored for a longer period, the spray gun
should be positioned with the adapter pointing downwards.
48
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
8.2 MAINTENANCE
Maintenance work should be undertaken regularly and carefully by qualifi ed and trained staff . They should be informed of specifi c hazards during their training.
The following hazards may arise during maintenance work:Health hazard from inhaling solvent vaporsUse of unsuitable tools and aids
Once the maintenance work is complete, the device must be checked by a qualifi ed person to ensure a reliable condition.
8.2.1 MAINTENANCE STAFF
8.2.2 SAFETY INSTRUCTIONS
Incorrect maintenance/repair!
Danger to life and equipment damage.
Repair or replacement of devices or parts of devices are only allowed to be performed outside the hazard area by qualifi ed personnel.
DANGER
Check hoses, pipes, and couplings every day and replace if necessary.
In accordance with the guideline for liquid ejection devices (ZH 1/406 and BGR 500 Part 2 Chapter 2.36):- The liquid ejection devices should be checked by an expert (e.g. Wagner service
technician) for their safe working conditions as required and at least every 12 months.
- If devices have been decommissioned, the examination can be suspended until the next start-up.
49
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
DANGER
8.3.1 TOOLS
For disassembling and assembling the gun the following tools are required:
Allen wrench SW 2Allen wrench SW 3Allen wrench SW 5Open-end wrench SW 5Open-end wrench SW 6Open-end wrench SW 8Open-end wrench SW 11Open-end wrench SW 12Open-end wrench SW 14Open-end wrench SW 19Open-end wrench SW 21Open-end wrench SW 22Ring spanner SW 9Torx wrench 20Torx wrench 25Assembly tool valve needle Order No. 2309368Assembly tool clamping screw Order No. 2325263
Incorrect maintenance/repair!
Danger to life and equipment damage.
Only a WAGNER service center or a suitably trained person may carry out repairs and replace parts.
Only repair and replace parts that are listed in the "Spare Parts" chapter and that are assigned to the device.
Before all work on the device and in the event of work interruptions:
- Disconnect the control unit from the mains. - Relieve the pressure from the spray gun and device. - Secure the spray gun against actuation.
Observe the operating manual and service instructions at all times when carrying out work.
8.3 DISASSEMBLY OF THE SPRAY GUN
50
B_03194
SW3
SW12SW12
B_03195
SW3
SW19
SW21
Torx 25
1
2
3
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
8.3.2 DISASSEMBLY OF THE SPRAY GUN
51
4
5
6
B_03197
SW9
B_03196
SW22
SW19
SW19
25
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Assembly tool for needle valve.Order No. 2309368
Assembly tool for the valve housingOrder No. 2325263
Note:
Loosen AC valve tip by hand using an assembly tool.
Do not pull out on contact wire.
Carefully release the cascade without pliers.
Use assembly tool, socket or ring spanner (no wrench).
Use screw driver to lever out the ring carefully.
Note:
If the fi tting (25) is not on the dismounted product hose when it is replaced, the fi tting must be removed from the gun adapter.
52
8
9
7
B_03198
SW6
SW5
SW2
14
5
2
6 7
3
ø 3
.0
B_03199
SW14
SW9
SW5
SW8
Torx 20
2
1
2
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
1. Remove pressure spring (4).2. Loosen clamping screw compl. (1) with
assembly tool (5).3. Unscrew the complete packing (3) via
valve rod unit complete (2, 6 and 7) or pull out the valve rod unit and unscrew it using an Allen wrench SW5.
4. If the loosened packing (3) is jammed in the hole, push from the front (see illustration above).
1. Loosen the oval head screw (1).2. Pull the air valve (2) out off the
hole.
53
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
8.4 CLEANING THE PARTS AFTER DISASSEMBLY
In Chapter 13 the part numbers for gun spare parts can be found as well as for wearing parts such as seals.
Incompatibility of cleaning agent and working medium!
Risk of explosion and danger of poisoning by toxic gasses.
Examine the compatibility of the cleaning agents and working media on the basis of the safety data sheets.
WARNING
Please note:
All reusable parts (except for the parts conducting high-voltage such as cascade, adapter, plug compl. etc.) should be cleaned thoroughly using a suitable cleaning agent.
The adapter, plug compl. and the handle inside must be clean and dry after cleaning. Care should be taken that these parts remain free of solvents, grease or sweat from the hands (salt water).
Spare parts may have safety-relevant properties. Use only WAGNER original spare parts and accessories. Defective parts, O-rings and seal sets must always be re-placed.
ATTENTION
54
1
2B_03448
B_03201a
SW143 Nm
SW9 1 Nm
Torx
20 1
4
2
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
8.5 ASSEMBLY OF THE SPRAY GUN
Assembly aids:
Order No. Description
1 9992590 Loctite 2222 9992698 Vaseline white PHHV II3 9992831 Loctite 5424 9992511 Loctite 2435 9992609 Anti-seize paste
Ensure the correct insertion position!
Ensu
re th
e co
rrec
t ins
ertio
n po
sitio
n!
55
3
B_03202
0.5 Nm
SW60.4 - 0.5 Nm
SW5
2
2
2
SW5/ 0.4 - 0.5 Nm
X = 123 ±0.1
SW2
1Nm
X
14
5
4 5
B_03203
SW91.8 Nm
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Set measure X with withdrawal nut and then fasten it with the threaded pin (SW2).
Push the valve rod unit and the complete packing together.
Screw the valve rod unit and the complete packing together.
Only as required:
Remove the valve rod unit.Tighten the complete packing.
Carefully insert the valve rod unit and mount the complete clamping screw (1) with assembly tool (5).
Slightly tighten AC valve tip by hand using an assembly tool(Order No. 2309368).
Assembly tool (Order No. 2325263)
Note:
Use assembly tool, socket or ring spanner (no wrench).
Ensure the correct insertion position.
Ensure the correct insertion position.
56
6
7
B_03205
SW3
0.8 Nm
SW21
SW19
B_03204
SW22
SW19
SW192.5 Nm
2
5
525
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Clean and degrease the inside of the adapter and the cascade, then grease the cascade surface with Vaseline.
Note:
Before assembling the product hose, check that no fi tting (25) is in the gun adapter!Check the fi tting for damage and replace if necessary (Order No. 2338853).
57
8
B_03206
Torx 25
9
B_03207
SW30.8 Nm
SW12
SW12
2
R1 R3R2
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Push the trigger upward into the air valve piston.
Ensure the correct insertion position!
58
10
B_03208
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Flat jet nozzleAssembly see Chapter 13.3.1.Various nozzle sizes see Chapter 12.2
Round jet nozzleAssembly see Chapter 13.3.2.Various nozzle sizes see Chapter 12.1.
59
B_03212
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
8.6 FUNCTION TEST AFTER ASSEMBLY OF THE GUN
8.6.1 TEST OF THE HIGH-VOLTAGE
Necessary test equipment:VM 500 or VM 5000 control unit and HV200 high-voltage tester. High-voltage measurement on spraying gun.
Connect gun cable to control unit. Take the spray gun in your hand and hold into open space. Switch on control unit and actuate trigger guard.The high-voltage should be 50 to 60 kV in dry ambient air. The value can be checked with the display on the control unit (VM 5000).Notice
The gun must be clean and dry and must not have any color or cleaning agent residues. In the case of ambient air with a high air humidity, the measured value can reduce to 40 to 50 kV.
High-voltage measurement with high-voltage tester
Place the ball of the high-voltage tester on the gun electrode and turn on the high-voltage. The measured value should be 60 to 70 kV.Notes
- When measuring the high-voltage the gun and the measuring device should be held at arms length as far from the body as possible.
- There should be no chargeable objects within a radius of 1 m; 3.28 ft of the place where the measurements are taken.
- The placing of the measuring ball of the high-voltage measuring device reduces the spraying of the high-voltage electrode. As a result the high-voltage value increases compared to the spraying in the free space.
Disruptive discharge test
Check the gun against ground with the grounding rod. No sparks should be formed.Note: in the vicinity of the electrode harmless corona discharges can occur.
Grounding rodOrder No. 175519
60
B_03213
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Connect test or air hose to the spray gun and switch on mains pressure to a maximum of 0.8 MPa; 8 bar; 116 psi.
Checking the air valve
The air valve must switch on and off correctly.Test up to approx. 0.8 MPa; 8 bar; 116 psi.
Air tightness
With the trigger unactuated, test for air tightness at the points marked in the illustration:
Connect high-pressure hose to the spray gun.Test the spray gun for tightness with solvent or spray oil (e.g. Macrol 52) and a maximum pressure of 25 MPa; 250 bar; 3,626 psi.Observe the following gun components:Product connection, nozzle body, product valve (no after-spraying).
8.6.2 AIR TEST
8.6.3 PRODUCT PRESSURE TEST
Exploding gas / air mixture!
Danger to life from fl ying parts and burns.
Never spray into a closed tank. Ground the tank.
DANGER
61
B_00071
B_03214
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
8.6.4 TEST OF SPRAY PATTERN
Start AirCoat spraying (without electrostatics)
1. Start up with product supply set to approx. 8 MPa; 80 bar; 1,160 psi operating pressure.2. Spray (release locking device and pull trigger) and at the same time, check the
atomization.3. Set the product pressure on the product supply to the point where a good product
atomization is achieved.4. Open the air pressure regulator for the atomizing air and adjust it so that an optimal
atomization is achieved. (The interrelation between spray pattern and atomizing air is shown in the fi gure below).
5. With the air adjustment on the gun, set the ratio shaping air / atomizing air so as to achieve an optimum spray pattern.
Note:
Repeat points 4 and 5 until the optimum spray pattern is reached (iterative process).
Spray pattern shapes
No atomization air Too little atomization air Correct amount of atomization air
Infl uence of the air adjustment on the spray pattern shape
The spray pattern can be adjusted to suit the object to be sprayed using the air adjustment. The illustration shows the infl uence of the shaping air regulator on the spraying pattern.Other nozzle sizes can be used to obtain larger or smaller spraying patterns.
Closed air adjustment
Completely opened air adjustment
Notice
The paint output can be changed by:changing the product pressure orusing a diff erent fl at jet nozzle (see Chapter 12.2).
62
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
8.7 HIGH-PRESSURE HOSES
The service life of the fl uid hoses is reduced due to environmental infl uences even when handled correctly.
Check hoses, pipes, and couplings every day and replace if necessary.As a precaution, fl uid hoses should be replaced after a period specifi ed by the operator.
Bursting hose, bursting threaded joints!
Danger to life from injection of product.
Ensure that the hose material is chemically resistant to the sprayed products.
Ensure that the spray gun, threaded joints, and product hose between the device and the spray gun are suitable for the pressure generated in the device.
Ensure that the following information can be seen on the high-pressure hose:
- Manufacturer - Permissible operating pressure - Date of manufacture
DANGER
63
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
9 INSPECTIONS
Observe safety instructions in Chapter 4.
9.1 PERIODICAL INSPECTIONS
For the safe operation of electrostatic manual coating systems for fl ammable liquid coating products, intervals for periodical inspections are defi ned as follows:
Inspection point Inspection interval Remarks
Gun cleaning, gun fl ushing daily Chapter 4.2.4, Chapter 8.1.3Hoses, tubes, couplings daily Chapter 8.7Grounding weekly Chapter 4.2.2, Chapter 6.4.5Inspection for damage weekly Chapters 8.1.3, 8.2, 8.3, 8.4 and 8.5Locking of the technical ventilation with the electrostatic manual coating system
annually Chapter 6.4.2
The above recommended intervals are maximum values and may be modifi ed by the operator depending on the local and operational conditions and the contamination.
Damaged devices must be decommissioned and repaired immediately.
64
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Functional fault Cause Remedy
Insuffi cient product output Nozzle too small. Select larger nozzle(see nozzle table 12.2 und 12.3).
Product pressure too low. Increase product pressure.Gun fi lter or high pressure fi lter clogged at pump.
Clean or replace fi lter.
Nozzle is clogged. Nozzle cleaning(see Chapters 7.3.3 to 7.3.8).
Poor spray pattern Atomizing air incorrectly adjusted. Readjust the atomizing air.Nozzle is too large. Select a smaller nozzle
(see nozzle table).Product pressure too low. Increase the product pressure at
pump.The product viscosity is too high. Thin product in accordance with the
manufacturer's instructions.Valve rod leaks Seals at the valve rod are damaged. Replace the seals (see Chapter 8).
Loose packing TightenPoor wrap-around Insuffi cient grounding. Check grounding.
Inadequate electric resistance of the lacquer.
Check lacquer resistance(see Chapter 2.5).
Spraying pressure too high. Readjust spraying pressure.Back-spray No grounding Check grounding.
Distance between spray gun and work piece too large.
Reduce distance between spray gun and work piece.
Nozzle nut placed too far forward Move nozzle nut back(Decrease air distributor ring gap).
No wrap-around High-voltage switched off . Switch on the high-voltage switch.No electrostatics. Repair malfunction as laid down
in the control unit operating instructions.
10 TROUBLESHOOTING AND RECTIFICATION
65
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
11 PRODUCT DISPOSAL
Do not dispose of used electrical equipment with household
refuse!
In accordance with European Directive 2002/96/EC on the disposal of used electrical equipment and its implementation in national law, this product may not be disposed of with the household refuse, but must be recycled in an environmentally correct manner.Wagner or one of our dealers will take back your used Wagner electric or electronic equipment and will dispose of it for you in an environmentally-friendly way. Please contact one of our service points, one of our representatives or us directly to arrange this.
NOTICE
66
B_03210
B_03209
B_03454
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
12 ACCESSORIES
12.1.1 ACR 5000 ROUND JET NOZZLE CAP
Order No. Designation
2344483 ACR 5000 round jet nozzle cap(with nozzle spanner, without AC round jet nozzle insert)
Order No. Designation
2309882 ACF 5000 air cap - LV suitable for low viscosity products (marked red)
2314203 ACF 5000 air cap - HV suitable for high viscosity products (marked blue)
12.2.1 ACF 5000 AIR CAPS (FLAT JET)
Order No. Marking Jet width Recommended gun fi lter
mm; inch
132720 11 approx. 250; 10 Red132721 12 approx. 250; 10 200 meshes132722 13 approx. 250; 10132723 14 approx. 250; 10
132724 * 15 approx. 250; 10132725 16 approx. 250; 10 Yellow132726 17 approx. 250; 10 100 meshes132727 18 approx. 250; 10132728 19 approx. 250; 10132729 20 approx. 250; 10 white132730 21 approx. 250; 10 50 meshes132731 22 approx. 250; 10
* Standard versionJet width in mm; inches at a distance of 30 cm; 11.8 inches from the object and at a pressure of 10 MPa; 100 bar; 1,450 psi.
12.1.2 AIRCOAT ROUND JET NOZZLE INSERTS
The round jet nozzles are especially suited to spray pipes, profi les and complex work pieces.
12.1 ROUND JET NOZZLES
12.2 FLAT JET NOZZLES
67
B_03163
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
12.2.2 ACF5000 AIRCOAT FLAT JET NOZZLES
Ord
er
No
.
Ma
rkin
g
Bo
re
mm
;
inc
h
Sp
ray
an
gle
Application
395107 07/10 0.18; 0.007 10° Natural lacquer395207 07/20 20°395407 07/40 40°395109 09/10 0.23; 0.009 10° Clear lacquer395209 09/20 20° Oils395309 09/30 30°395409 09/40 40°395509 09/50 50°395609 09/60 60°395111 11/10 0.28; 0.011 10° Synthetic resin lacquer395211 11/20 20° PVC lacquer395311 11/30 30°395411 11/40 40°395511 11/50 50°395611 11/60 60°395811 11/80 80°395113 13/10 0.33; 0.013 10° Lacquer395213 13/20 20° Base coat395313 13/30 30° Primer395413 13/40 40° Filler395513 13/50 50°395613 13/60 60°395813 13/80 80°395115 15/10 0.38; 0.015 10° Filler395215 15/20 20° Rust proofi ng paints395315 15/30 30°395415 15/40 40°395515 15/50 50°395615 15/60 60°395815 15/80 80°395217 17/20 0.43; 0.017 20° Rust proofi ng paints395317 17/30 30° Latex paints395417 17/40 40°395517 17/50 50°395617 17/60 60°395817 17/80 80°
68
B_03163
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500O
rde
r N
o.
Ma
rkin
g
Bo
re
mm
;
inc
h
Sp
ray
an
gle
Application
395219 19/20 0.48; 0.019 20° Rust proofi ng paints395319 19/30 30° Latex paints395419 19/40 40°395519 19/50 50°395619 19/60 60°395819 19/80 80°395221 21/20 0.53; 0.021 20° Mica paints395421 21/40 40° Zinc rich paints395521 21/50 50° Rust proofi ng paints395621 21/60 60° Glue paints395821 21/80 80°395423 23/40 0.58; 0.023 40°395623 23/60 60°395823 23/80 80°395425 25/40 0.64; 0.025 40°395625 25/60 60°395825 25/80 80°395427 27/40 0.69; 0.027 40°395627 27/60 60°395827 27/80 80°395429 29/40 0.75; 0.029 40°395629 29/60 60°395829 29/80 80°395431 31/40 0.79; 0.031 40°395631 31/60 60°395831 31/80 80°395435 35/40 0.90; 0.035 40°395635 35/60 60°395835 35/80 80°
69
B_00019
B_03221
M
F
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
12.3 FILTER
Order No. Designation
3204604 Edge fi lter 60 mesh (white)3204605 Edge fi lter 100 mesh (black)9999002 Edge fi lter 200 mesh (yellow)
12.4 REDUCTION FITTINGS FOR HIGH-PRESSURE HOSES
The classifi cation of WAGNER fi ttings is consistent with the following classifi cation, each separated by high-pressure and low pressure fi ttings:
Double fi tting - male / male thread Reduction fi tting - female / male thread Adjustable screw - female / male thread: allows precise angle adjustment (swivel) 90° elbow - adjustable or male / male thread (elbow fi tting) Bulkhead fastener - male / male thread with pressure-resistant feed-through Stopper - male thread for closing (plug fi tting)
Hose fi tting with union nut and sealing cone (hose fi tting)The short description of the fi ttings are as follows:
Materials, SSt = Stainless steelNominal pressure (in bar)
1st thread, e.g. G1/4", 1/4"NPS2nd thread, e.g. G1/4", 1/4"NPS, M16x1.5
M: male (outer thread) F: female (interior thread)Short description see table above, e.g. RF = Reduction Fitting
Order No. Designation
384555 Reduction fi tting-RF-FM-M16x1,5-1/4"NPS-PN530-SSt384559 Reduction fi tting RF-FM-M16x1,5-G1/4"-PN530-SSt384556 Reduction fi tting RF-FM-M16x1,5-3/8"NPSM-PN530-SSt34041 Reduction fi tting RF-FM-1/4"NPS-M16x1,5--PN270-SSt
179732 Reduction fi tting RF-FM-1/4"NPS-3/8"NPS--PN270-SSt179247 Reduction fi tting RF-FM-1/4"NPS-G1/4"--PN270-SSt
In the large Wagner Accessories Catalogue for wet coating you will also fi nd other material fi ttings.
70
23 4
5
B_03217
1
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
12.5 HOSES AND ELECTRIC CABLES
12.5.1 STANDARD HOSE SETS AND COMPONENTS
Order No. Designation
1 1 2339171 GM 5000EAC hose set (7.5 m)Consists of:
2 1 9984573 High-pressure hose-DN4-PN270-¼"NPS-7.5 m-PA3 1 2339152 Air hose complete (8.0 m)4 1 2339157 GM 5000E gun cable (10.0 m)5 7 m 3676437 Protection hose fabric PP30 (8.0 m)
Order No. Designation
1 1 2339172 GM 5000EAC hose set (10.0 m)Consists of:
2 1 2302374 High-pressure hose-DN4-PN270-¼"NPS-10.0 m-PA3 1 2339153 Air hose complete (10.5 m)4 1 2339158 GM 5000E gun cable (15.0 m)5 10.5 m 3676437 Protection hose fabric PP30 (10.5 m)
Order No. Designation
1 1 2339173 GM 5000EAC hose set (15.0 m)Consists of:
2 1 9984573-15 High-pressure hose-DN4-PN270-¼"NPS-15.0 m-PA3 1 2339154 Air hose complete (15.5 m)4 1 2339159 GM 5000E gun cable (20.0 m)5 15.5 m 3676437 Protection hose fabric PP30 (15.5 m)
Order No. Designation
1 1 2339174 GM 5000EAC hose set (20.0 m)Consists of:
2 1 9984573-20 High-pressure hose-DN4-PN270-¼"NPS-20.0 m-PA3 1 2339155 Air hose complete (20.5 m)4 1 2339160 GM 5000E gun cable (25.0 m)5 20.5 m 3676437 Protection hose fabric PP30 (20.5 m)
Note regarding the product hose:
- Nominal pressure 25 MPa; 250 bar; 3,626 psi- Internal diameter 4 mm; 0.16 inch- Inner hose material PA
71
A****B****
B_03849
1
23
A
BC
D
E
(**)
B_03845(*)(***)
123
(****)
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Hose colors:
Product hose yellowAir hose blue
Dimensions:
Air hose: inside diameter 6.5 mm; 0.26 inchProduct hose: inside diameter 4 mm; 0.16 inch, nominal pressure 25 MPa; 250 bar; 3,626 psi
Material of product hose: PA
Order No. Description A [mm] B [mm] C [mm] D [mm] E [mm]
2339171 GM 5000EAC hose set (7.5 m) 29±2 65±2 300±10 20±10 1500+100
2339172 GM 5000EAC hose set (10 m) 29±2 65±2 300±10 20±10 1500+100
2339173 GM 5000EAC hose set (15 m) 29±2 65±2 300±10 20±10 1500+100
2339174 GM 5000EAC hose set (20 m) 29±2 65±2 300±10 20±10 1500+100
Notes:
(*) Melt the hose ends at both sides (gun/pump) and turn approx. 5 cm of each hose end to the inside.(**) Fix the protective hose with cable ties on both sides only once at the product hose (internally)(***) Fix the hose set within the protective hose approx. once per meter by means of adhesive tape, starting
at distance E.Cable ties are only permitted at the ends of the protective hose (see **)!
(****) If the air swivel joint (Order No. 2324766) and/or the material swivel joint (Order No. 2327060) is/are used, the hose set has to be adapted accordingly.If the air swivel joint is used, dimension A becomes 60 mm!
If the material swivel joint is used, dimension B becomes 94 mm!
1 Product hose2 Air hose3 Electric cable
72
B_03216
23
4
5
1
6
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
12.5.2 HOSE SETS FOR LOW-RESISTANCE PRODUCTS
Order No. Designation
1 1 2339179 GM 5000EAC hose set (7.5 m), Low RConsists of:
2 1 2310468 EAC high-pressure product hose, complete (7.5 m) Low R3 1 2339152 Air hose complete (8.0 m)4 1 2339157 GM 5000E gun cable (10.0 m)5 8 m 3676437 Protection hose fabric PP30 (8.0 m)
Order No. Designation
1 1 2339180 GM 5000EAC hose set (10.0 m), Low RConsists of:
2 1 2310469 EAC high-pressure product hose, complete (10.0 m) Low R3 1 2339153 Air hose complete (10.5 m)4 1 2339158 GM 5000E gun cable (15.0 m)5 10.5 m 3676437 Protection hose fabric PP30 (10.5 m)
Order No. Designation
1 1 2339181 GM 5000EAC hose set (15.0 m), Low RConsists of:
2 1 2310470 EAC high-pressure product hose, complete (15.0 m) Low R3 1 2339154 Air hose complete (15.5 m)4 1 2339159 GM 5000E gun cable (20.0 m)5 15.5 m 3676437 Protection hose fabric PP30 (15.5 m)
Order No. Designation
1 1 2339182 GM 5000EAC hose set (20.0 m), Low RConsists of:
2 1 2310471 EAC high-pressure product hose, complete (20.0 m) Low R3 1 2339155 Air hose complete (20.5 m)4 1 2339160 GM 5000E gun cable (25.0 m)5 20.5 m 3676437 Protection hose fabric PP30 (20.5 m)
Note regarding the product hose:
- Nominal pressure 25 MPa; 250 bar; 3,626 psi- Internal diameter 4 mm; 0.16 inch- Inner hose material FEP- Pos. 6 connecting fi tting AC Order No. 2338853
73
B
FC
D
E
(**)
B_03846(*)(***)
123
A****
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Hose colors:
Product hose greyAir hose blue
Dimensions:
Air hose: inside diameter 6.5 mm; 0.26 inchProduct hose: inside diameter 4 mm; 0.16 inch, nominal pressure 25 MPa; 250 bar; 3,626 psi
Material of product hose: FEP
Order No. Description A [mm] B [mm] C [mm] D [mm] E [mm] F [mm]
2339179 GM 5000EAC hose set (7.5 m), Low R 206±2 177±2 300±10 20±10 1500+100 188±12339180 GM 5000EAC hose set (10 m), Low R 206±2 177±2 300±10 20±10 1500+100 188±12339181 GM 5000EAC hose set (15 m), Low R 206±2 177±2 300±10 20±10 1500+100 188±12339182 GM 5000EAC hose set (20 m), Low R 206±2 177±2 300±10 20±10 1500+100 188±1
Notes:
(*) Melt the hose ends at both sides (gun/pump) and turn approx. 5 cm of each hose end to the inside.(**) Fix the protective hose with cable ties on both sides only once at the product hose (internally)(***) Fix the hose set within the protective hose approx. once per meter by means of adhesive tape, starting
at distance E.Cable ties are only permitted at the ends of the protective hose (see **)!
(****) If the air swivel joint (Order No. 2324766) is used, the hose set has to be adapted accordingly.If the air swivel joint is used, dimension A becomes 237 mm!
1 Product hose2 Electric cable3 Air hose
74
Nicht unter Spannungtrennen
"Do not part under
voltage"
B_03219
P_00265
B_03224
B_03693
B_03692
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
Order No. Designation
2339161 GM 5000E extension cable 10m; 32.81 ft
2339162 GM 5000E extension cable 20 m; 65.6 ft
12.5.3 GUN CABLES AND GUN CABLE EXTENSIONS
Order No. Designation
2319653 Protective gun coating
259010 HV200 N high-voltage tester
2326041 Paint resistance meter
999080 Wet fi lm thickness gauge
50342 Viscosity cup DIN 4 mm; 0.16 inch
12.6 MISCELLANEOUS
75
B_03451
B_03681
B_03699
B_03720
B_03720
B_03719
B_03719
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
2309368 Assembly tool valve needle
128901 Nozzle spanner ACR
2325263 Assembly tool clamping screw
2326485 GM 5000E wall mount (left/right)
232476 Swivel joint air
2327060 Fitting-SJM-GM5000EAC-1/4"NPS (swivel product)
2327061 GM 5000EAC swivel joint kit
76
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
77
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
13 SPARE PARTS
13.1 HOW CAN SPARE PARTS BE ORDERED?
Always supply the following information to ensure delivery of the right spare part:
Order number, designation and quantity
The quantity need not be the same as the number given in the quantity column " " on the lists. This number merely indicates how many of the respective parts are used in each component.
The following information is also required to ensure smooth processing of your order:Billing addressDelivery addressName of the person to be contacted in the event of any queriesType of delivery (normal mail, express delivery, air freight, courier, etc.)
Identifi cation in spare parts lists
Explanation of column " " (labeling) in the following spare parts lists:
Wearing partNote: No liability is assumed for wearing parts.
Not part of the standard equipment but available as a special accessory.
Incorrect maintenance/repair!
Risk of injury and equipment damage.
Have repairs and part replacements be carried out only by specially trained staff or a WAGNER service center.
Before all work on the device and in the event of work interruptions:
- Switch off the energy/compressed air supply. - Relieve the pressure from the spray gun and device. - Secure the spray gun against actuation.
Observe the operating instructions for any work.
WARNING
78
B_03153a
23
19
20
21
7
5
89
10
1211
13
1415
18
16
17
6
422
1
25
27
24
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
13.2 GM 5000EAC SPARE PARTS LIST
79
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
GM 5000EAC spare parts listOrder No. Designation
1 1 2344473 GM 5000EAC basic version2 1 2314283 Contacting AC3 1 9952777 High resistance, bare4 1 9960808 Socket contact component5 1 - GM 5000EAC adapter, complete
Details see Chapter 13.2.16 1 2314361 Hook7 1 - GM 5000EAC handle, complete
Details see Chapter 13.2.28 2 9900308 Hexagon socket head cap screw9 1 2312183 Lid complete
10 1 9900386 Hexagon socket head cap screw11 1 2311970 Sealing plug12 1 2307104 Screw plug13 1 2312180 Air regulation complete14 1 9971182 O-ring15 1 9971182 O-ring16 1 2314360 Trigger17 1 2307283 Cylindrical helical spring18 2 2310617 Oval head screw with hexagon19 1 2314359 Product hose AC, complete20 1 3204605 Edge fi lter 100 mesh (black)
(for diff erent edge fi lter sizes see Chapter 12.3)21 1 2308764 Hose fi tting AC22 1 2350454 Union nut AC, complete24 1 2308699 Cover seal25 1 2338853 Connecting fi tting AC27 1 2349376 Spacer
1 2326336 GM 5000EAC service set = Wearing part = Included in service set
80
B_04368
2
1
12
109
8
3
4
56
7
2122
1124
123 ±0.1 mm
4.8425 ±0.004 inch
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
13.2.1 GM 5000EAC - ADAPTER SPARE PARTS LIST
81
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
5000EAC adapter spare parts listOrder No. Designation
1 1 - GM 5000EAC adapter, complete2 1 2313314 AC air manifold ring3 1 2307180 O-ring, sheathed4 1 2312175 Valve housing AC, complete5 1 2312186 Valve needle AC, complete6 1 2314272 GM 5000EAC adapter7 1 2312181 Cascade, complete8 1 9974166 O-ring9 1 2307062 Clamping screw valve rod
10 1 2311562 Rod seal11 1 2313639 Valve rod unit AC12 1 2340024 Packing, complete21 1 2307059 Withdrawal nut22 1 9901411 Threaded pin with hexagon socket24 1 2325263 Assembly tool clamping screw
1 2326336 GM 5000EAC service set = Wearing part = Included in service set
82
7
1
B_04775
8
9
10
12
5
6
32
4 23
11
18
13
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
13.2.2 GM 5000EAC - HANDLE SPARE PARTS LIST
83
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
GM 5000EAC handle spare parts listOrder No. Designation
1 1 - GM 5000EAC handle, complete2 1 2307288 Fitting3 1 9971025 O-ring4 1 2307290 Hose holder5 1 2312182 Plug, complete6 1 2314270 Handle, complete7 1 2307232 Adapter seal8 1 2311952 Stop screw9 1 2309825 Oval head screw with hexagon
10 1 2310692 Seal11 1 2311182 Straight pin12 1 2309400 Safety clip13 1 2312189 Air valve18 1 9974218 O-ring23 1 9974166 O-ring
1 2326336 GM 5000EAC service set = Wearing part = Included in service set
84
B_03168
2
3
14
5
6
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
13.3 ACCESSORIES SPARE PARTS LISTS
13.3.1 FLAT JET NOZZLES SPARE PARTS LIST
Flat jet nozzles spare parts listOrder No. Designation
1 1 2350454 Union nut AC, complete
21 2309882 ACF 5000 air cap - LV (red)1 2314203 ACF 5000 air cap - HV (blue)
3 1 2311777 Nozzle guard AC4 1 2344488 Union nut AC5 1 2311217 O-ring, sheathed6 1 2319525 Flat electrode set = Wearing part
85
B_03169
23
1
4
56
910
11
12
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
13.3.2 ACR 5000 ROUND JET NOZZLE CAP SPARE PARTS LIST
ACR 5000 round jet nozzle cap spare parts listOrder No. Designation
1 1 2344483 ACR 5000 round jet nozzle cap2 1 2307220 Nozzle nut3 1 2315310 O-ring4 1 132351 Nozzle screwed connection holder5 1 2344487 Nozzle body6 1 2319526 Round electrode set9 1 132516 Nozzle screw joint, complete
10 1 2307216 Sealing fi tting11 1 2311217 O-ring12 1 128901 Nozzle wrench, complete = Wearing part
86
OPERATING MANUAL
EDITION 07/2014 ORDER NUMBER DOC 2344500
14 WARRANTY
14.1 IMPORTANT NOTES REGARDING PRODUCT LIABILITY
14.2 WARRANTY CLAIM
As a result of an EC regulation eff ective from January 1, 1990, the manufacturer shall only be liable for his product if all parts originate from him or are approved by him, and if the devices are properly mounted, operated and maintained.The manufacturer will not be held liable or will only be held partially liable if third-party accessories or spare parts have been used.With genuine WAGNER accessories and spare parts, you have the guarantee that all safety regulations are complied with.
Full warranty is provided for this device:We will at our discretion repair or replace free of charge all parts which within 24 months in single-shift, 12 months in 2-shift or 6 months in 3-shift operation from date of receipt by the purchaser are found to be wholly or substantially unusable due to causes prior to the sale, in particular faulty design, defective materials or poor workmanship.The type of warranty provided is such that the device or individual components of the device are either replaced or repaired as we see fi t. The resulting costs, in particular shipping charges, road tolls, labour and material costs will be borne by us except where these costs are increased due to the subsequent shipment of the device to a location other than the address of the purchaser.We do not provide warranty for damage that has been caused or contributed to for the following reasons:Unsuitable or improper use, faulty assembly or commissioning by the purchaser or a third party, normal wear, negligent handling, defective maintenance, unsuitable coating products, substitute products and the infl uence of chemical, electrochemical or electrical agents, except when the damage is attributable to us.Abrasive coating products such as red lead, emulsions, glazes, liquid abrasives, zinc dust paints and so forth reduce the service life of valves, packings, spray guns, nozzles, cylinders, pistons etc. Wear and tear due to such causes are not covered by this warranty.Components that have not been manufactured by WAGNER are subject to the original warranty of the manufacturer.Replacement of a component does not extend the period of warranty of the device.The device should be inspected immediately upon receipt. To avoid losing the warranty, we or the supplier company are to be informed in writing about obvious faults within 14 days upon receipt of the device.We reserve the right to have the warranty compliance met by a contracting company.The services provided by this warranty are dependent on evidence being provided in the form of an invoice or delivery note. If the examination discovers that no warranty claim exists, the costs of repairs are charged to the purchaser.It is clearly stipulated that this warranty claim does not represent any constraint on statutory regulations or regulations agreed to contractually in our general terms and conditions.
J. Wagner AG
CERTIFIE
D
Order No. 2344500Edition 07/2014
Germany
PhoneFaxE-mail
Switzerland
PhoneFax
More contact adresses on the Internet at:
Enterprises/Sites/WAGNER worldwide
Subject to changes without notice
Doc
umen
t No.
111
6374
0Ve
rsio
n -