Training

PORT- THE CONNECTION TO THE SERVER OR PC. ON SATEON PRO THIS IS ALWAYS IPFIELD NETWORK-A GROUP OF CONTROLLERS CONNECTED TO PORT USUALLY ON 485LINE HEADER- AN ETHERNET/485 CONVERTER UNIT THAT ALLOWS A LINE OF 485 CONTROLLERS TO BE CONNECTED TO A PCENCLOSURE- A POWER SUPPLY UNIT THAT ALLOWS UP TO TWO CONTROLLERS OR ONE CONTROLLER AND ONE IP BOARD TO BE MOUNTED IN IT.

Terminology

• Cable Types• Data Comms• 485 Data Comms• Ethernet Data Comms• Sateon Pro Controllers

– 485– Ethernet

• Sateon Pro Enclosures

System Setup Part 1 - Hardware

Line Header to Panel (Comms Converter) 2 Pair Belden (or equivalent) #8723 1200m

per Segment Cat 5 – Use Twists – Not for electrically noisy environments – 200m

Panel to Reader See Reader Documentation 50m (if using Keypad Interface)

External Inputs 2 Core Cable (Alarm) 100m

Locks Use suitable gauge cable for current draw and volt drop

Current Draw (Amps) x Distance (Meters) x Wire Resistance per Meter (Ohms) = Voltage Drop (Volts)

Cable Types

SATEON PRO MINI PC

485 Data Comms

Ethernet Door Controllers

Data Comms

485 Panels

RS-485 Two wire (plus Ground) – 1 Pair

10 Panels on a line maximum Max 1200m No T taps / loops Each pair should be twisted All controllers will need an

Ethernet Line Header

Sateon Pro 485

Sateon Pro Line Header

• Can be mounted in standard Enclosure

Ethernet Line Header

PORT connects a SATEON Comms Engine to PanelsSEGMENT - 1,200m length of Belden (2 or 4 wire) Field Network - Cable from LINE HEADER to last Panel

10 Panels - address range 1 to 63

485 Panels are Polled

1 2 3 4 10 Addresses do NOT have to be sequential…..

Data Line Overview

Ethernet Panels

Each IP Panel has it’s own IP address and connects directly to the network via a RJ45 Plug

Panels are Polled and will immediately Synchronise with SATEON

Sateon Pro Ethernet

PRO 485 (Card Access)

Present CardPanel decides to unlock the door (or not)Waits for next Poll from SATEON PROTells SATEON PRO about the card and access was allowed

PRO ETHERNET (Card Access)

Present CardPanel decides to unlock the door (or not)Tells SATEON about the card and access was allowed

485 (Input to Output on another Panel)

Activate input on Panel 1Panel 1 waits for next Poll from SATEON PROPanel 1 tells SATEON PRO about the input activationSATEON PRO broadcasts to Panel 2 to activate the output

PRO ETH (Input to Output on another Panel)

Activate input on Panel 1Panel 1 tells SATEON about the input activationSATEON broadcasts to Panel 2 to activate the output

PRO485 vs PRO ETHERNET

• Request To Exit contact must be N/O• Break Glass Unit contact must be N/O

Sateon Pro Panel Break Glass Monitoring

Sateon Pro Summary

Intelligent Door Controller485

TCP/IP2 doors read in. 1 door read in/out

Additional alarm inputCard capacity 500 users

Real-time processing at doorLED and sounder outputs

Memory buffer whilst off-line (4,000 Events)Upgrade flash whilst system is workingVolt Free Changeover output for Locks

Can be mounted in any PSU

Sateon Pro Controller Connections

Sateon Pro Lock Connections

Sateon Pro Reader Wiring

Door Sensor – Normally closed

Dual Door Sensor – Normally closed - Monitored

Door Sensor – Normally closed - Monitored

Sateon Pro Door Monitor Wiring

• Request To Exit contact must be N/O• Break Glass Unit contact must be N/O

Sateon Pro Break Glass Monitoring

Input – Normally closed or Normally Open Input – Normally closed or Normally Open

Sateon Pro Input Wiring

IO RS485 TCP/IP

AES Encryption on eSeries Real-time processing Memory buffer whilst off-line (4,000 Events) Upgrade flash whilst system is working 8in / 4out• Can be mounted in any Enclosure

Sateon Pro Input / Output

Sateon Pro Input / Output 485 & Ethernet

EZ Enclosures

2 x Sat Pro board or 1 x Sat Pro board and 1x IO board 1 x 7Ah Battery Built in tamper to lid Built in power supply (3A) with 2A available for external

equipment, i.e. locks and readers

Sateon Pro Mains Enclosure

Sateon Pro Mains Enclosure

2 x Sat Pro Panel or 1 x Sat Pro Panel & 1x IO board 1 x 7Ah Battery Built in tamper to lid Built in power supply with 2A available for external

equipment, i.e. locks and readers

POE 802.3af 44VDC 350mA 15.4W 900mAPOE+ 802.3at 44VDC 1700mA 25.5W 2000mA

Sateon Pro POE+ Enclosure

EZ POE Enclosure

IP Panel

IP Panel

IP Panel

Up to 10 x RS485 Panels

Sateon Pro Hardware Overview

Question 1 - How long can a segment of the Comms line be?Question 2 - What is the value of the EOL resistor that should be fitted to the beginning and end of the Comms line.Question 3 - How many cards does the Sateon Pro board hold? Question 4 – How many controllers does it support?Question 5 - Can you wire a Sateon Pro485 board to a Sateon Pro IP?Question 6 - How many Sateon Pro boards fit in an Enclosure?Question 7 - What is the max Amps available for locking in an Enclosure?

Q&A Were you listening???

• Install SATEON PRO• Licence SATEON PRO• Add a 485 Panel (I/O Board)• Add an Input• Add a eSeries (IP) Panel• Update the Firmware in a Panel• Add a Door• Add a Reader• Add a Person• Add Access• Add a Token• Unlock a door

System Setup Part 1 - Software

Username : admin Password : sateon Must change password on first logon Can change to sateon if you wish

SATEON - LOGON

SATEON Main Screen

• Access Control• Control Centre• Reports• Event Configuration• System Configuration• Visitors not included on Sateon Pro

SATEON Hubs

• Apply the licence• Verify the licence• Setup the Token Type• Setup the Site Name• Setup the Comms Engine

SATEON – Initial Tasks

• Access Control – Token Management – Token Types - Add

SATEON – Create the Token

• Access Control – Device Management - Site – Main Site

SATEON – Create the Site

Access Control – Device Management - Comms Engine – Add

SATEON Create the Comms engine

• IP Panel or Line Header.• When supplied are DHCP.• Will assign an address in 169.254.?.? Range if no DHCP available.• Use the eSeriesDeviceProgrammer tool to set the IP address.• Encrypted devices will not come on line until ‘seeded’ using the

eSeriesDeviceProgrammer tool with access to a valid SATEON licence.• eSeriesDeviceProgrammer will find devices in the same subnet and allow

you to program them.• eSeriesDeviceProgrammer can be run from (and set the encryption of an

Ethernet device) from any SATEON client machine (Config required)

SATEON Programming Pro Devices

SATEON EseriesDeviceProgrammer.exe

SATEON

• A 485 Panel wires to a Field Network• Each field network has at least one Port, the Port is the physical connection

between the LAN / WAN and the Field Network.• A Field Network may have many Ports.• A Field Network may have 10 Panels.

• Access Control – Device Management – Field Network– Add• Access Control – Device Management - Port– Add• Access Control – Device Management - Panel– Add

SATEON

SATEON

SATEON

SATEON

• Access Control – Access Management – Access Groups

SATEON

Time schedules are used to define the periods during which things can happen within the SATEON access control system. For example;

When access is permitted at certain doors When events are reported When actions can occur.

A time schedule is set up as a combination of time patterns, where each time pattern defines one or more periods of time. Each individual period of time with a defined start and end time is an appointment. Appointments can consist of an entire day.

SATEON

• Install SATEON PRO• Licence SATEON PRO• Add a 485 Panel• Add a PRO(IP) Panel• Update the Firmware in a Panel• Add a Door• Add a Reader• Add a Person• Add Access• Add a Token• Unlock a door

Recap