training 1 installation

9400 AWY R2.1PSC Training

Benoît MAGNAN, Product Support Center - WTD

September, 2007

9400 AWY R2.1 | September 2007 All Rights Reserved © Alcatel-Lucent 2007

Agenda

1. HW Configuration and IDUs Installation

2. NMS Integration overview

3. First Configuration : Configuration Wizard

4. First Configuration : TCO usage

5. Commissioning : CT-K usage

6. Configuration Changes

7. Maintenance : Alarms overview and root causes


1 HW Configuration and IDUs Installation


HW Configuration and IDUs Installation

HW Configuration – Basic Configuration Functions

Basic Configuration allows up to 16E1 user line interface

Basic IDU configuration includes the following functions

Mux / Demux : Line interface up to 16E1

Flash Card containing Equipement Software and Licence Key

Equipement Controller

IDU-ODU interfaces

NMS interfaces

Power Supply

Man – Machine interfaces

I/O



HW Configuration – Front and Back Pannels in Basic Configuration



HW Configuration – Optional Plug-ins

IDU may be equiped with

User line Plug-in (5)

16E1 plug-in to reach 32 E1 tributaries

Or Ethernet / Data plug-in

ESC – Audio Plug-in (6 and 7)

For 64 kbps or 9600 bps ESC

For EOW

Basic Eth Plug-in

16E1 Plug-in

ESC – Audio Plug-in



IDU Configuration – Interfaces Description (1/4)

Reference Description Picture Description

1 Power Supply Input

(3 pins SubD male)

A1 : + Battery

A2 : Ground

A3 : - Battery

2 Power Supply Switch

(2 positions togle switch)

I : On position

0 : Off position

3 Eth/OS interface

(RJ45)

1 : Tx +

2 : Tx –

3 : Rx +

6 : Rx –

Green LED : Eth Link up (on) / down (off)

Yellow LED : Activity (Tx or Rx)

4 Debug Interface Green LED : Equipement Controller alive

Refer to debug section for wiring





5 – a E1 Plug-in Refer to 13 for E1 connection

5 - b Eth Plug-in

(RJ45, qty 2)

Green LED : Eth Link up (on) / down (off)

Yellow LED : Activity (Tx or Rx)

6 Audio – User Serv

(44 pins SubD female)

Refer to installation handbook for pin-out

7 Telephone

(RJ11)

8 IDU-ODU Interface

(N female)

Center Conductor : - 55 VDC

Outer Conductor : Ground





9 Aknowledge

(Push button)

To aknowledge equipement alarms

10 Reset

(Push button)

To reset the Equipement Controller

11 Lamps Test

(Push Button)

To lighten all front pannel LEDs

12 ECT (F) Interface


Pin to pin cable for PC serial interface

13 E1 user interface

(68 pins SCSI female)

2 : Trib # 1, Out + (Trib # n : pin # 2n)

36 : Trib # 1, Out – (Trib # n : pin # 34 + 2n)

3 : Trib # 1, In + (Trib # n : pin # 2n+1)

37 : Trib # 1, In - (Trib # n : pin # 34 + 2n + 1)

1, 34, 35, 68 : Ground





14 Interconnection

(100 pins SCSI female)

15 ALM – NMS


16 LEDs ON : IDU powered on

RDI : Remote Defect Indicator

MIN : Minor Alarm

Yellow EOW blinking : ring

Yellow EOW : busy

Green EOW : free

ODUW : Tx On

LDI : Local Defect Indicator

MAJ : Major Alarm

ATTD : Aknowloedged alarms

ANT : correct RSL

ANT blinking : Low RSL (not yet implemented)



HW Configuration – Protection overview

Extension unit allows to have the protection of

E1 tributaries multiplex / demultiplex (EPS)

/!\ Ethernet ports are not protected. EPS should be set in revertive mode

Radio Transmission failure (HST)

Reception failure (RPS)

Due to propagation activity or card failure

Protection configurations are 1+1 HST and 1+1 FD



IDU Configuration – Extension unit

LEDs ON : IDU powered on

ODUW : Tx On

ANT : correct RSL

ANT blinking : Low RSL (not yet implemented)

The only specific part is the LED one



IDU Configuration – Patch Panel

Patch Panel has been designed to be used in 1+1 configuration, but it can be used in 1+0 configuration as well (even recommanded in case of a future upgrade).

1 -> 8

9 -> 16

1 -> 16 Main

1 -> 16 Ext

17 -> 24

25 -> 32

17 -> 32 Main

17 -> 32 Ext

To/from DDF

To/from IDU

37 pins SubD female

68 pins SCSI female



IDU Configuration – Service Protection Box

Service Protection box allows to have the same interfaces as AWY R2.0 on line side and to split ESC to both IDUs

To/from DDF

To/from IDU



IDU Installation – Interconnections : tributaries

1 -> 8

9 -> 16

1 -> 16 Main

1 -> 16 Ext

1 -> 16 Main

1 -> 16 Ext

17 -> 24

25 -> 32

17 -> 32 Main

17 -> 32 Ext

17 -> 32 Ext

17 -> 32 Main SCSI

To/from DDF

3CC52118AAAA : 1 m



IDU Installation – Interconnections : I/O and NMS

SCSI

To/from DDF

3CC52116AAAA



IDU Installation – Interconnections : Audio and ESC

SCSI

To/from DDF

3CC52116AAAA



IDU Installation – Interconnections : Full installation…



IDU Installation

Caution on IDU – ODU connector

Before to put the IDU-ODU cable, check that the hexagonal washer is properly tightened (failure on R2.0 has been noticed: ICP, Cable LOS)

Caution on inter-IDUs SCSI

Insure that the cable is properly plugged (failures on R2.0 has been noticed : RUP, ICP, transmission KO…)

Caution on connector columns

When disconnecting an interface, take care that columns may remain attached to the screws


2 NMS Integration overview

training 1 installation

Documents