tqd-00001 - conventional safety - training and ... · to support requirements of ohsa and...

Master PDF Created: 07Sep2004 10:35

BRUCE TRAINING DEPARTMENT

TQD-00001 R001

CONVENTIONAL SAFETY

TRAINING AND QUALIFICATIONS DESCRIPTION

IMPLEMENTATION DATE: AUGUST 01, 2004

Training Program Manager:

Date:B. Brown

Line Manager:

Date:G. Kozak

Approved by Site Training Committee:

Date:F. Saunders

Approved for Issue - VERIFY STATUS PRIOR TO USE

DOCUMENT CONTROL SHEET


Department: BRUCE TRAINING DEPARTMENT

Document Type: Training & QualificationsDescription

Document Number: TQD-00001

Title: Conventional Safety Review Date:

Rev # Date Description of RevisionPrepared/Revised by

R000 April, 2002 Initial Issue. M. Latimer

R001 June, 2004 Revision to new format, additional respiratoryand ergonomic qualifications.

M. Latimer


TQD-00001 R001

Implementation Date: August 01, 2004Conventional Safety Training and Qualification Description


TABLE OF CONTENTS1.0 SCOPE AND APPLICABILITY.................................................................................... 1

2.0 EXCEPTIONS ............................................................................................................. 1

3.0 ROLES AND ACCOUNTABILITIES............................................................................ 1

3.1 Training Manager......................................................................................................... 1

3.2 Training Delivery Section Manager .............................................................................. 1

3.3 Manager Safety Programs ........................................................................................... 1

3.4 Line Managers............................................................................................................. 2

3.5 Trainer ......................................................................................................................... 2

4.0 ENTRY-LEVEL CRITERIA .......................................................................................... 2

5.0 QUALIFICATIONS ...................................................................................................... 2

6.0 TRAINING PROGRAM................................................................................................ 3

6.1 Asbestos...................................................................................................................... 3

6.2 Confined Space ........................................................................................................... 3

6.3 Driver........................................................................................................................... 3

6.4 Emergency Measures.................................................................................................. 4

6.5 Fall Protection.............................................................................................................. 4

6.6 ISRS............................................................................................................................ 4

6.7 Medicals ...................................................................................................................... 4

6.8 OHSA .......................................................................................................................... 5

6.9 Respiratory Protection ................................................................................................. 5

6.10 Safety Awareness........................................................................................................ 5

7.0 TRAINER TRAINING AND QUALIFICATION REQUIREMENTS................................ 5

8.0 TRAINING EVALUATIONS......................................................................................... 5

9.0 ACRONYMS................................................................................................................ 6

10.0 REFERENCES ............................................................................................................ 6


TQD-00001 R001



APPENDIX 1: SPECIFIC QUALIFICATIONS .......................................................................... 7

APPENDIX 2: ADDITIONAL QUALIFICATIONS................................................................... 11

APPENDIX 3: REQUIREMENTS FOR SPECIFIC QUALIFICATIONS .................................. 12

APPENDIX 4: PREREQUISITE QUALIFICATIONS OF SPECIFIC QUALIFICATIONS ........ 31

APPENDIX 5: PROGRAM ELEMENT PREREQUISITES...................................................... 32

APPENDIX 6: PROGRAM GROUPS..................................................................................... 33

APPENDIX 7: PERSONAL DEVELOPMENT PROGRAM ELEMENTS ................................ 35


TQD-00001 R001


Page 1


1.0 SCOPE AND APPLICABILITY

This Training and Qualification Description (TQD) describes the Conventional SafetyTraining process and the related training qualifications required for all Bruce Poweremployees, contractors and visitors. The training and qualifications are requirementsmandated by legislation (Federal and Provincial), licensing, and Bruce Powerprocedures.

2.0 EXCEPTIONS

The major job families have safety training as an integral part of their training programs(e.g., welding safety). These topics will not be included or duplicated in theConventional Safety TQD.

3.0 ROLES AND ACCOUNTABILITIES

3.1 Training Manager

Meets the expectations identified in BP-PROG-02.02, Worker Training andQualification.

3.2 Training Delivery Section Manager

Reviews and approves training materials.

Maintains training material content current, technically accurate, of high quality, and inaccordance with a systematic approach to training.

Establishes content authority to support technical content of training.

Defines Station Subject Matter Expert (SME) requirements and arranges for therelease of personnel to support the development of Conventional Safety Training andQualification courses.

Ensures the day-to-day implementation of Conventional Safety Training andQualification requirements, except for On-the-Job Training and Evaluation activities,are carried out.

Acts as the Bruce Power authority for Driver Training Licence renewal.

3.3 Manager Safety Programs

Advises, in advance, the Safety Training Section when they purchase new safety workequipment (e.g., gas monitor, new fall protection harness).

Advises, in advance, the Safety Training Section when procedure(s) are introduced orchanged.


TQD-00001 R001


Page 2


Provides opportunities for Safety Trainers to experience the work safety culture of thejob family on an annual basis. For example, assists with Job Safety Analysis, monitorfall protection and confined space procedure compliance as per the Safety TrainingDelivery Manager’s request.

3.4 Line Managers

Meets expectations identified in BP-PROG-02.02, Worker Training and Qualification.

Links applicable Conventional Safety Training Qualification for their staff and assignsonly qualified personnel, both contract and regular staff, to work independently.

3.5 Trainer

Trains and evaluates staff, visitors, and contractors who require Conventional SafetyTraining and Qualification.

Develops and maintains Conventional Safety Training course materials.

Recommends granting of Conventional Safety training credits for staff, visitors, andcontractors who have successfully completed the training.

Recommends Remedial Training or qualification level reductions for staff, visitors, andcontractors who do not successfully complete initial or continuing Conventional SafetyTraining and Qualification.

4.0 ENTRY-LEVEL CRITERIA

Must complete GET training per TQD-00010.

5.0 QUALIFICATIONS

Qualifications applicable to Conventional Safety Training apply to all activities acrossthe site to all Job Families. See Appendix 2 of your Job Family TQD for a list ofapplicable Conventional Safety qualifications.

Appendix 1 provides a listing of available Qualifications.


TQD-00001 R001


Page 3


To make selection easier the listings in Appendix 1 are grouped as follows:

AsbestosConfined SpaceDriverEmergency MeasuresFall ProtectionISRSMedicalsOHSARespiratory ProtectionSafety Awareness

6.0 TRAINING PROGRAM

Conventional Safety Training contains both initial and Continuing Training courses.The first time trainees complete the course, the training is considered Initial Training.

Descriptions of Program Element (PEL) requirements for each qualification are inAppendix 3 of this document.

6.1 Asbestos

To support worker to Type 1, 2 and 3 operations as required by OHSA and Designatedsubstance regulations 837 and 838, and BP-SM-00045, Bruce Power AsbestosControl Program.

6.2 Confined Space

To support requirements of OHSA and Industrial and Construction Regulations, BrucePower Safety Rules and BP-SM-00023, Entry into Confined Spaces.

3-year requalification for all positions.

The courses are structured so that:

• Co-ordinator includes surveyors, monitor and entry.• Surveyor includes monitor and entry.• Monitor includes entry.

6.3 Driver

Includes knowledge and skills training to upgrade Ministry of Transportation Licencesand improve on the road driving skills. To support BP-SM-00044, Safe Driving.

Transportation of Dangerous Goods (TDG), excluding Class 7, to provide certificationper Federal TDG Regulations In Clear Language. Certificate is issued after successfulcompletion of the course. Requalification every 3 years.


TQD-00001 R001


Page 4


Lift Truck Training as required by the OHSA and its Industrial and ConstructionRegulations, CSA standard Industrial Lift Truck Operator Training B335-94 andOntario Ministry of Labour, Guideline for the Safe Operation and Maintenance ofPowered Lift Trucks. JPMs are provided for each class of lift truck, each with a 2-yearrequalification.

Elevated Work Platform Training as required by OHSA Regulation 213 and 851, CSAStandards CAN 3-B 354(.1, .2 & .4) and CAN-CSA-C225.

• If the class of EWP is propane powered and the employee will be changing thetanks, they must be linked to the Propane Handler Qualification 5128.

• Fall Protection Training is also required.

6.4 Emergency Measures

First Aid training as specified by St John Ambulance. Emergency First Aid to meetrequirements of Confined Space Monitor, electrical worker and safety person.Standard First Aid to meet requirements of OHSA Regulation 1101, First AidRequirement.

Fire protection training to support CSA 293-95, Fire Protection for CANDU NuclearPower Plants and OHSA Construction Project Regulations O. Reg. 213.

6.5 Fall Protection

Provided to meet requirements of OHSA and its Industrial and Constructionregulations and BP-SM-00001, Fall Protection.

6.6 ISRS

Courses provided or accredited by external consultants from the Industrial AccidentPrevention Association (IAPA) to develop staff for the implementation of the IndustrialSafety Rating System at Bruce Power. For further details contact the Loss ControlCoordinator.

Systematic Cause Analysis Technique (SCAT) provides the participant with the theoryand practice for ISRS Accident and Incident Investigation process. This technique is asimplified basic cause evaluation technique, which is used during investigations ofinjuries and near misses, substandard acts and substandard conditions that couldhave caused an injury. Required by all those required to complete Corrective ActionPlans.

6.7 Medicals

Medicals are initiated by completing an Annual Health Screening Request(FORM-11767).

Appendix 7 provides a list of Medical credits given. As required by qualifications theyare included in Appendix 3.


TQD-00001 R001


Page 5


Noise Exposed individual monitoring per BP-SM-00039, Noise Control and HearingConservation.

6.8 OHSA

Joint Health and Safety Committee member Certification training for both Industrialand Construction Committees. Appendix 7 provides a list of possible continuingtraining activities and courses.

6.9 Respiratory Protection

Provided to meet requirements OHSA and its regulations, CSA Standard Z94.4-02,Selection, Use, and Care of Respirators, BP-SM-00030, Requirements for RespiratoryProtection and BP-SM-00061, Maintenance Inspection and Storage of RespiratoryProtection.

Includes the need to have a prerequisite Annual Health Screening Request(FORM-11767) and associated plastics, non-SCBA and/or SCBA medical.

6.10 Safety Awareness

Training required to participate in an Access Controlled Area function perBP-SM-00048, Conventional Safety Guidelines For Entry Into Access ControlledAreas.

Ergonomics training to support BP-SM-00037, Body Mechanics and as specified bythe Bruce Power Ergonomists.

Introduction to Event Free Tools is provided to assist supervisors in using thesehuman performance error reduction aids.

7.0 TRAINER TRAINING AND QUALIFICATION REQUIREMENTS

The Training Delivery Section Manager Conventional Safety will determine individualTrainer training needs and assign Trainers to participate in initial training courses andother learning activities to meet those needs as per TQD-00003, Trainer Training andQualification Description.

8.0 TRAINING EVALUATIONS

There are no special assessments of training required beyond what is directed byBP-PROC-000213, Training – Administer Training Evaluation.


TQD-00001 R001


Page 6


9.0 ACRONYMS

• CSA - Canadian Standards Association• OHSA - Ontario Occupational Health and Safety Act

10.0 REFERENCES

• TQD-00010, General Employee Training and Qualification Description

• TQD-00003, Trainer Training and Qualifications Description

• BP-PROG-02.02, Worker Training and Qualification

• BP-PROC-00174, Training Exemption Process

• BP-PROC-00211, Training – Administer On-The-Job Training (OJT)

• BP-PROC-000176, Training – Administer Remedial Training

• BP-PROC-000213, Training – Administer Training Evaluation


TQD-00001 R001


Page 7


APPENDIX 1: SPECIFIC QUALIFICATIONS

AsbestosQAL ID Name Location

10892 WORKING WITH ASBESTOS BNDFor the Worker their Supervisor and supervising Contract Administrators/Coordinators who through daily workactivities maybe exposed to asbestos materials. Per BP-SM-00045, Bruce Power Asbestos Control Program.

10893 ASBESTOS TYPE 2 & 3 REMOVALS BNDRequired for Workers involved in large scale asbestos abatement jobs with Type 2 and Type 3 removals. PerPB-SM-00045, Bruce Power Asbestos Control Program.

Confined SpaceQAL ID Name Location

2475 CONFINED SPACE - ENTRY ONLY BNDThis qualification is required for anyone who requires entry into a Confined Space per BP-SM-00023.

2477 CONFINED SPACES - ENTRY COORDINATOR, SURVEYOR, MONITOR & ENTRY BNDThis qualification is required to fulfill the position of Entry Coordinator as required by BP-SM-00023.

2478 CONFINED SPACES - SURVEYOR, MONITOR & ENTRY BNDThis qualification is required to fulfill the role of Surveyor - Gas Tester as required by BP-SM-00023.

2479 CONFINED SPACES- ENTRY MONITOR & ENTRY BNDThis qualification is required to fulfil the role of Entry Monitor as required by BP-SM-00023.

DriverQAL ID Name Location

209 CLASS 2-ELECTRIC MOTOR NARROW AISLE TRUCK BNDRequired by staff who operate electric motor narrow aisle trucks. Lift codes 1 thru 7.

210 CLASS 3-ELECTRIC MOTOR-DRIVEN HAND TRUCKS BNDRequired by staff who operate an electric motor hand/rider truck. Lift codes 1 through 10.

211 CLASS 4-INTERNAL COMBUSTION ENGINE-CUSHION TIRES BNDRequired by staff who operate internal combustion engine trucks - cushion tires only. Lift code 3.

212 CLASS 5-INTERNAL COMBUSTION ENGINE-PNEUMATIC TIRES BNDRequired by staff who operate internal combustion engine trucks - pneumatic tires only. Lift code 4.

213 CLASS 6-ELECTRIC & INTERNAL COMBUSTION ENG TRACTOR BNDRequired by staff who operate electric motor or internal combustion engine tractor. Lift code 1.

214 CLASS-1 ELECTRIC MOTOR RIDER TRUCK BNDRequired by staff who operate an electric motor rider truck---counterbalanced,pneumatic/cushion tire.sit-downincludes high and low platform. Lift codes 4&5.

215 COACHING THE EXPERIENCED DRIVER - < 2,500 KM/YR BNDQualification for individuals who drive<2500km/y on company business. Satisfies training requirements as specifiedin BP-SM-00044, Safe Driving

216 COACHING THE EXPERIENCED DRIVER - >15,000 BNDQualification for individuals who drive > 1500km/yr on company business. Satisfies training requirements as specified

in BP-SM-00044, Safe Driving

217 COACHING THE EXPERIENCED DRIVER >2,500-<15,000 KM BNDQualification for individuals who drive >2500 and < 1500km/yr on company business. Satisfies training requirements

as specified in BP-SM-00048, Safe Driving

707 PROFESSIONAL DRIVER BNDThis qualification is required by all staff whose duties involve driving Class A,B,C,D,E and F type vehicles.

736 CLASS-7 ROUGH TERRAIN LIFT TRUCKS BNDRequired by staff who operate rough terrain fork-lift trucks. Lift code 1.

2538 TRANSPORTATION OF DANGEROUS GOODS QUALIFIED BNDExcluding Class 7 (radioactive) goods, this TDG qualification is required by all Bruce Power staff who will be doingany of the following, with respect to dangerous goods entering or leaving the site (the Controlled Area): Receive /Handle / Ship / Transport. A TDG qualification IS NOT required for dangerous goods activities within theControlled Area - this is covered by WHMIS regulations.Issued with successful completion of the training, is acertificate. The certificate or a copy of it must be available (i.e. in your pocket or desk) when carrying out a TDG


TQD-00001 R001


Page 8


activity. This qualification is also not applicable for any shipments by air.Class 7 TDG activities require

2819 ELEVATED WORK PLATFORM - BOOM TYPE BNDQualification for operator of Elevated Work Platform - Boom Type

2824 ELEVATED WORK PLATFORM - ROLLING BNDClassroom training and JPM for operation of Rolling type Elevated Work Platform

2829 ELEVATED WORK PLATFORM-SELF PROPELLING PAVED/SLAB BNDQualification for operator of Elevated Work Platform - Self Propelling Paved / Slab

4649 ELEVATING WORK PLATFORM SELF-PROPELLED OFF/SLAB BNDProvincial/Federal legislation specifies an employee must be trained in the safe operation of elevated work

5128 PROPANE CYLINDER EXCHANGE PROCESS BNDThis Qualification will train Staff to Safely Handle and Change Propane(LPG)tanks associated with liquid propanecarburetted industrial machines, ForkLift, Scribbers and Mobile Cranes ,Etc

12617 CLASS 2 - ORDER PICKER OPERATION-RAYMOND MODEL 162 BNDQualification for Knowledge & Skills required for the safe/efficient operation of the Raymond Order Picker.

12618 CLASS 2 - SWING REACH OPERATION- RAYMOND MODEL 537 BNDQualification for Knowledge & Skills required for the safe/efficient operation of the Raymond Swing Reach

Emergency MeasuresQAL ID Name Location

388 FIRST AID - EMERGENCY BND

1138 FIRE PROTECTION -EXTINGUISHER BNDThis qualification is required by all plant staff as per the Fire Loss control guide and corporate safety rules.

12019 FIRE WATCH - CONTROL OF IGNITION SOURCES BNDKnowledge and skills required to meet responsibilities under the Control of Ignition Sources procedure

12097 FIRE RESPONSE FOR STAFF ON ROUNDS BNDThis qualification is intended for staffs who regularly complete rounds or investigate problems in the stations.Typically Operators and Security.The qualification includes the Fire Extinguisher course.

Fall ProtectionQAL ID Name Location

1059 FALL PROTECTION EQUIPMENT INSPECTOR BNDThis qualification is required by all staff assigned to regularly inspect fall protection equipment.

1589 FALL PROTECTION QUALIFIED BNDThis qualification is required for all staff who will be working at a required task presenting a hazard of falling adistance greater than three (3) metres to the next safe level. Per BP-SM-00001, Fall Protection.It covers thecorrect theory and use of Fall Arrest Systems (FAS). A FAS is an assembly of components joined together sothat when the assembly is connected to a fixed support, it is capable of arresting a worker’s accidental fall.Correct use of a fall arrest system greatly reduces risk of injury in the event of a fall; however, it does not

ISRSQAL ID Name Location

3001 ISRS AUDITOR BNDThis qualification is required by individuals assigned to conduct ISRS Loss Control audits. In addition to the training requirements specified here, individuals are required to conduct an audit under the guidance of a qualified DNVISRS qualified auditor.

MedicalsQAL ID Name Location

1767 NOISE EXPOSED INDIVIDUALS BNDQualification tracks individuals who require regular hearing tests. Testing is administered by Health Services.

OH&SAQAL ID Name Location

6108 JH&S COMMITTEE MEMBER BNDThis qualification is required by all employees who have been selected to serve on a JH&S committee.

10232 JH&S COMMITTEE MEMBER - BTU BND


TQD-00001 R001


Page 9


Respiratory ProtectionQAL ID Name Location

5268 HALF MASK AIR PURIFYING RESPIRATOR ( MSA) BNDThis qualifcation is required by all staff who are required to wear a half mask air purifying respirator manufacturedby MSA in the course of their work. Half-mask, air-purifying negative pressure. For Comfo II and Comfo

5270 FULL FACE AIR PURIFYING RESPIRATOR (MSA) BNDThis qualifcation is required by all staff who are required to wear a full face air purifying respirator manufacturedby MSA in the course of their work. Full-Face, air-purifying negative proessure. For the MSA Ultra Twin.

5271 POWERED AIR PURIFYING RESPIRATOR (MSA) BNDThis is required by all individuals who require Respiratory Protection using a Powered air-purifying respirator MSAModel Optimair 6A equipped with a comfo half-mask in the course of their duties

5272 POWERED AIR PURIFYING RESPIRATOR (3M) BNDThis qualifcation is required by all staff who are required to wear a powered air purifying respirator manufacturedby 3M in the course of their work. Powered air-purifying. For 3M 7800

5273 HALF MASK AIR SUPPLIED RESPIRATOR (US SAFETY) BNDThis qualifcation is required by all staff who are required to wear a half mask air supplied respirator manufacturedby US Safety in the course of their work. Supplied air, full face mask. For US Safety 1520H & 152 modified.

5276 FULL FACE AIR SUPPLIED RESPIRATOR (SCOTT) BNDThis qualifcation is required by all staff who are required to wear a full face air supplied respirator manufactured by Scott in the course of their work. Supplied air, full face mask. For Full airline with Scott-o-ramic facepiece,constant flow/pressure demand

5277 FULL FACE AIR SUPPLIED RESPIRATOR (ISI) BNDThis qualifcation is required by all staff who are required to wear a full face air supplied respirator manufactured by ISI in the course of their work. Supplied air, full face mask. For Panaseal full face mask, ARAP-C - ISI.

5279 SCBA RESPIRATOR (ISI) BNDThis qualifcation is required by all staff who are required to wear SCBA manufactured by ISI in the course of theirwork. SCBA open circuit. For ISI Magnum

5280 SCBA RESPIRATOR VIKING - ERT ONLY BNDThis qualifcation is required by all staff who are required to wear SCBA manufactured by MSA in the course oftheir work. SCBA (open circuit) Viking with Airswitch mask

10472 ADVANTAGE 200LS AIR PURIFYING RESPIRATOR (MSA) - FOR WELDERS ONLY BNDThe Advantage 200LS air purifying respirator by MSA. This respirator is designed to fit under a welders face shield and is intended for WELDERS ONLY

11537 BULLARD AIRLINE RESPIRATOR BNDThis qualification is required by all staff who are required to wear the Bullard Series 88VX airline respirator in thecourse of their work. The Bullard 88VX series airline respirator provides respiratory protection for abrasive blastersand painters and consists of three components, respirator helmet assembly, breathing tube assembly and airsupply hose. The Bullard is a loose fitting respirator so a fit testing is not required

11577 PC 4 GAS MASK - SECURITY ONLY BNDThis Gas Mask is for Security use only.The mask had to meet a design criterion of 6667 and 5884 when wornwith spectacles. The design criterion is based on the NATO standard for NBC masks.

11637 ULTRAVUE FULL FACE POWERED AIR PURIFYING RESPIRATOR (PAPR) - MSA BNDThis respirator is used for various type 3 asbestos work and other work where required. It operates with a motorand battery pack which is also equipped with a High efficiency particulate filter.

11638 SPEEDGLAS WELDING HELMET POWERED AIR PURIFYING RESPIRATOR (PAPR) - BNDHORNELL ADFLOThis respirator is used for various welding jobs and has a welding plate built into the helmet. It operates with amotor and battery pack which is also equipped with a High efficiency particulate filter.

11657 PLASTIC SUIT - RESPIRATORY PROTECTION BNDThis qualification is required by all staff to wear plastic suits. Plastic suits are considered respiratory protectionand as such fall under the requirements of BP-SM-0030 and CSA Z94.4

11717 RAM’S HORN CONTINUOUS AIR SUPPLY RESPIRATOR BNDRam’s HornIs classified as a Loose Fitting Respirator - Comes with a belt and is worn around the neck. Thisrespirator delivers a continuous supply of air to the user and is usually worn with a tyvek hood. This respiratordoes not require a fit test.

12077 SUPERVISORS RESPIRATORY PROTECTION KNOWLEDGE BNDThis qualification is for supervisors of staff who use respiratory protection.As required by PB-SM-00030,Requirements For Respiratory Protection and CSA Standard Z94.4-02, Selection, Use and Care of Respirators


TQD-00001 R001


Page 10


12477 N95 DUST MASK PARTICULATE RESPIRATOR - BIOLOGICAL PROTECTION BNDThis qualification is for Health Services and Medical Emergency Responders ONLY. For use when an N95disposable mask is used for biological particulate protection.

Safety AwarenessQAL ID Name Location

1277 AWARENESS FOR SUPERVISOR OF WORKER ENTERING AN ACA BNDAs required by BP-SM-00048, Conventional Safety Guidelines for Access Controlled Areas

1298 ACCESS CONTROL DESK ATTENDANT AWARENESS FOR ENTERING AN ACA BNDAs required by BP-SM-00048, Conventional Safety Guidelines for Access Controlled Areas

2402 VAULT COORDINATOR AWARENESS FOR ENTERING AN ACA BNDAs required by BP-SM-00048, Conventional Safety Guidelines for Access Controlled Areas

2418 WORKER AWARENESS FOR ENTERING AN ACA BNDAs required by BP-SM-00048, Conventional Safety Guidelines for Access Controlled Areas

2803 SWITCHYARD SAFETY AWARENESS BNDThis is a safety awareness qualification for unsupervised (non-operator) staff needing to enter and work in theswitchyard. Hydro One determines the safety requirements and training requirements for entering switchyards.

12017 INDUSTRIAL ERGONOMIC RISK ASSESSOR BNDQualification for Industrial Ergonomic Risk Assessor

12018 OFFICE ERGONOMIC RISK ASSESSOR BNDQualification for Office Ergonomic Risk Assessor

12237 SEWAGE BIO-HAZARD EXPOSURE BNDHolder is permitted contact with systems containing sewage or other bio-hazards

12357 HEALTH AND SAFETY LAW BNDAs an Bruce Power supervisor, promote, create and maintain a safe workplace environment by being proactive indemonstrating supervisory responsibilities to the standards of Bruce Power and as prescribed by the OccupationalHealth and Safety Act and its associated Regulations.


TQD-00001 R001


Page 11


APPENDIX 2: ADDITIONAL QUALIFICATIONS

Not applicable for this TQD.


TQD-00001 R001


Page 12


APPENDIX 3: REQUIREMENTS FOR SPECIFIC QUALIFICATIONS

AsbestosQual Id Name Location Critical? Auto Cert. Revert To

10893 ASBESTOS TYPE 2 & 3 REMOVALS BND N YRequired for Workers involved in large scale asbestos abatement jobs with Type 2 and Type 3 removals. PerPB-SM-00045, Bruce Power Asbestos Control Program.

PEL ID Type Name Location Envir Duration RequalType/Period

1583 CRS ASBESTOS TYPE 2 & 3 REMOVALS BND FIELD 1 day(s) 36 QThis course covers the work practices and safety equipment regulations involved in large scale asbestos abatement jobs with Type 2 and Type 3 removals.The course is delivered by WESA.

Qual Id Name Location Critical? Auto Cert. Revert To

10892 WORKING WITH ASBESTOS BND N YFor the Worker their Supervisor and supervising Contract Administrators/Coordinators who through daily workactivities maybe exposed to asbestos materials. Per BP-SM-00045, Bruce Power Asbestos Control Program.


62465 CRS WORKING WITH ASBESTOS - CBT BND CBT 2 hour(s) 36 QFor the Worker their Supervisor and supervising Contract Administrators/Coordinators who through dailywork activities maybe exposed to asbestos materials. Before this course is started - it is very important to have completed reading the Procedure, BP-SM-00045.

Confined SpaceQual Id Name Location Critical? Auto Cert. Revert To

2475 CONFINED SPACE - ENTRY ONLY BND Y NThis qualification is required for anyone who requires entry into a Confined Space per BP-SM-00023.


6653 CRS CONFINED SPACE - ENTRY INITIAL/REQUAL BND CLASSROOM 4 hour(s) 36 DUpon completion of this course the participant will have the knowledge required to work safely in aconfined space.The course material is the same for initial and requalification.


2477 CONFINED SPACES - ENTRY COORDINATOR, SURVEYOR, BND Y Y MONITOR & ENTRYThis qualification is required to fulfill the position of Entry Coordinator, Surveyor or to Enter a ConfinedSpace as required by BP-SM-00023.


6525 CRS SAFETY AWARENESS INITIAL TRAINING BND CLASSROOM 4 day(s)Basics of safety equipment and personal barrier concepts. This credit is given on succesful completionof a variety of safety-related modules.

6663 CRS CONFINED SPACE - COORDINATOR BND CLASSROOM 2.5Upon completion of this course the candidate will have knowledge of the procedures, practices, and requirements for all aspects of work in a confined space.

6688 CRS CONFINED SPACE COORD.-REQUAL. BND CLASSROOM 1 day(s) 36 DThis course will requalify people who have taken the "Confined Space Coordinator course (6663).Course prerequisite is 6663 within 3 years.


TQD-00001 R001


Page 13



2478 CONFINED SPACES–SURVEYOR, MONITOR & ENTRY BND Y NThis qualification is required to fulfill the position of Surveyor (Gas Tester) or to Enter a Confined Spaceas required by BP-SM-00023.


6655 CRS CONFINED SPACE - SURVEYOR BND CLASSROOM 1.5 36 DINITIAL/REQUAL

On completion of course candidate will have knowledge of procedures, practices, & requirements foratmospheric testing of confined space. Will demonstrate ability to use oxygen analyzer combustile gasindicator & toxic gas analy equip.


2479 CONFINED SPACES-ENTRY MONITOR & ENTRY BND Y NThis qualification is required to fulfil the role of Entry Monitor or to Enter a Confined Space as required by BP-SM-00023.


6654 CRS CONFINED SPACE - MONITOR BND CLASSROOM 4 hour(s) 36 DUpon completion of this course the candidate will have the knowledge of procedures and practicesrequired to monitor work in a confined space.

6666 CRS FIRST AID - EMERGENCY BND CLASSROOM 1 day(s) 36 DCourse will consist of five compulsory modules and one rescuer CPR for the elective module.

DriverQual Id Name Location Critical? Auto Cert. Revert To

209 CLASS 2-ELECTRIC MOTOR NARROW AISLE TRUCK BND N NRequired by staff who operate electric motor narrow aisle trucks. Lift codes 1 thru 7.


7107 CRS LIFT TRUCK TRAINING BND CLASSROOM 1 day(s)Theory of lift truck operation and safety.Requires applicable lift truck Class Job Performance Measure(JPM) after course to obtain qualification - see TQD-00001.

7144 JPM ELECTRIC MOTOR NARROW AISLE TRUCKS BND FIELD 2 hour(s) 24 Q Electric Motor Narrow Aisle Trucks practical testing .LIFT CODE TYPE OF EQUIPMENT1 High Lift Straddle 2 Order Picker 3 Reach Type Outrigger 4 Sideloaders 5 Swing Mast6 Turret Trucks - Man on Board 7 Turret Trucks - Ground Level


210 CLASS 3-ELECTRIC MOTOR-DRIVEN HAND TRUCKS BND N NRequired by staff who operate an electric motor hand/rider truck. Lift codes 1 through 10.



7145 JPM ELECTRIC MOTOR HAND/RIDER TRUCKS BND FIELD 2 hour(s) 24 QElectric Motor-Driven Hand Trucks practical testing.LIFT CODE TYPE OF EQUIPMENT1 Low Lift Platform 2 Low Lift Walkie Pallet 3 Tractors 4 Sideloaders 5 Reach Type Outrigger6 High LiftStraddle 7 High Lift Counter-Balanced 8 Low Lift Walkie/Rider Pallet 9 Low Lift Rider Pallet10 Low Lift Rider Platform


211 CLASS 4-INTERNAL COMBUSTION ENGINE-CUSHION TIRES BND N NRequired by staff who operate internal combustion engine trucks - cushion tires only. Lift code 3.



TQD-00001 R001


Page 14



7146 JPM INTERNAL COMBUSTION ENGINE TRUCKS BND FIELD 2 hour(s) 24 QCUSHION

Internal Combustion Engine Lift Trucks - Cushion Tires practical testing.Fork, Counter-Balanced


212 CLASS 5-INTERNAL COMBUSTION ENGINE-PNEUMATIC TIRESBND N NRequired by staff who operate internal combustion engine trucks - pneumatic tires only. Lift code 4.



7147 JPM INTERNAL COMBUSTION ENGINE TRUCKS BND FIELD 2 hour(s) 24 QPNEUMATIC

Internal Combustion Engine Lift Trucks - Pneumatic Tires practical testing.Fork, Counter-Balanced(Pneumatic Tires) Lift Code 4


213 CLASS 6-ELECTRIC & INTERNAL COMBUSTION ENG TRACTOR BND N N

Required by staff who operate electric motor or internal combustion engine tractor. Lift code 1.PEL ID Type Name Location Envir Duration Requal

Type/Period


7148 JPM ELECTRIC MOTOR AND INTERNAL BND FIELD 2 hour(s) 24 QCOMBUSTION ENGINE TRACTORS

Electric and Internal Combustion Engine Tractors practical testing.Sit-down Rider Lift Code 1


214 CLASS-1 ELECTRIC MOTOR RIDER TRUCK BND N NRequired by staff who operate an electric motor rider truck---counterbalanced,pneumatic/cushion tire.sit-downincludes high and low platform. Lift codes 4&5.



7143 JPM ELECTRIC MOTOR RIDER TRUCKS BND FIELD 2 hour(s) 24 QClass 1: Electric Motor Rider Trucks practical testing. Three Wheel Electric Trucks, Sit-Down LiftCode 4 and Counterbalanced Rider Type, pneumatic/Cushion Tire, Sit-Down (Includes High And LowPlatform) Lift Code 5


736 CLASS-7 ROUGH TERRAIN LIFT TRUCKS BND N NRequired by staff who operate rough terrain fork-lift trucks. Lift code 1.



7149 JPM ROUGH TERRAIN FORK-LIFT TRUCKS BND FIELD 2 hour(s) 24 QRough Terrain Lift Trucks practical testing. All Rough Terrain Fork-lift Trucks Lift Code 1


TQD-00001 R001


Page 15



215 COACHING THE EXPERIENCED DRIVER - < 2,500 KM/YR BND N N

Qualification for individuals who drive<2500km/y on company business. Satisfies training requirements as specifiedin BP-SM-00044, Safe Driving


7125 CRS COACHING EXPERIENCED DRIVERS. (LIGHT BND CLASSROOM 4 hour(s) 36 QVEHICLES)

This Coaching for Experienced Drivers course (C.E.D.) is for light vehicles.


216 COACHING THE EXPERIENCED DRIVER - >15,000 BND N N

Qualification for individuals who drive > 1500km/yr on company business. Satisfies training requirements as specifiedin BP-SM-00044, Safe Driving





7123 CRS VEHICLE HANDLING DEFENSIVE DRIVING BND CLASSROOM 1.5 daysCOURSE

Ontario Safety League’s "Defensive Driving" Course. Theory of Safe Vehicle Operation.

7131 CRS VEHICLE HANDLING (FIELD) BND FIELD 2 hour(s)On the road driver training, any type of vehicle, this would normally be an In Car Evaluation (>15000 km) up to 2 hour session.


217 COACHING THE EXPERIENCED DRIVER >2,500-<15,000 KM BND N N

Qualification for individuals who drive >2500 and < 1500km/yr on company business. Satisfies training requirementsas specified in BP-SM-00048, Safe Driving






2819 ELEVATED WORK PLATFORM - BOOM TYPE BND Y NQualification for operator of Elevated Work Platform - Boom Type


7119 CRS ELEVATING WORK PLATFORM BND CLASSROOM 4 hour(s)Theory of elevated work platform operation and a practice session to prepare for the practicalevaluation.In addition to this course a practical evaluation is required for the type of elevated platformyou wish to qualify for. Operators should also be Fall Arrest Qualified.

7155 JPM ELEVATING WORK PLATFORM-BOOM-TYPE BND FIELD 2 hour(s)Elevating work platform boom type practical evaluation.


2824 ELEVATED WORK PLATFORM - ROLLING BND N NClassroom training and JPM for operation of Rolling type Elevated Work Platform


TQD-00001 R001


Page 16




7150 JPM ELEVATING WORK PLATFORM-ROLLING BND FIELD 2 hour(s)Elevating work platform rolling practical evaluation.


2829 ELEVATED WORK PLATFORM-SELF PROPELLING PAVED/SLAB BND YN

Qualification for operator of Elevated Work Platform - Self Propelling Paved / SlabPEL ID Type Name Location Envir Duration Requal

Type/Period


7151 JPM ELEVATING WORK PLATFORM - ON SLAB BND FIELD 2 hour(s)-SELF PROPELLED

Elevating work platform self propelled paved/slab practical evaluation.


4649 ELEVATING WORK PLATFORM SELF-PROPELLED OFF/SLAB BND Y NProvincial/Federal legislation specifies an employee must be trained in the safe operation of elevated work



7153 JPM ELEVATING WORK PLATFORM - OFF SLAB BND FIELD 2 hour(s)-SELF PROPELLED

Elevating work platform self-propelled off/slab practical evaluation.


707 PROFESSIONAL DRIVER BND Y NThis qualification is required by all staff whose duties involve driving Class A,B,C,D,E and F type vehicles.


7134 CRS AIR BRAKES BND CLASSROOM 1.5 60 DTheory, operation, and maintenance of single and combination unit air brakes.

7127 CRS VEHICLE HANDLING PROFESSIONAL DRIVER BND CLASSROOM 3.5 60 DIMPROVEMENT COURSE

Ontario Safety League’s "Professional Driver Improvement" Courses for drivers who operate a Class"A", "C", or "D" licence. Theory of safe vehicle operation.

7130 CRS VEHICLE SAFETY PROFESSIONAL BND CLASSROOM 1 day(s)Rules and regulations for operation of vehicles having a gross weight greater than 1100 kg(Class "A", "C" or "D").


5128 PROPANE CYLINDER EXCHANGE PROCESS BND N NThis Qualification will train Staff to Safely Handle and Change Propane(LPG)tanks associated with liquid propanecarburetted industrial machines, ForkLift,Scribbers and Mobile Cranes ,Ect


6942 CRS PROPANE CYLINDER HANDLER BND CLASSROOM 4 hour(s) 36 DTo develop skills and knowledge to handle and change propane cylinders in the workplace safely to


TQD-00001 R001


Page 17


corporate and legal requirements.This course is equivalent to PEL7140.


2538 TRANSPORTATION OF DANGEROUS GOODS QUALIFIED BND Y NExcluding Class 7 (radioactive) goods, this TDG qualification is required by all Bruce Power staff who will be doing any of the following, with respect to dangerous goods entering or leaving the site (the Controlled Area): Receive / Handle / Ship / Transport. A TDG qualification IS NOT required for dangerous goods activities within theControlled Area - this is covered by WHMIS regulations.Issued with successful completion of the training, is acertificate. The certificate or a copy of it must be available (i.e. in your pocket or desk) when carrying out a TDGactivity. This qualification is also not applicable for any shipments by air.Class 7 TDG activities requirequalification in Qual 2794 or 2795.


7021 CRS TRANSPORTATION OF DANGEROUS GOODS BND CLASSROOM 1 day(s) 36 DTRAINING

Excluding Class 7 (radioactive) goods, this TDG training equips the student with the knowledge and skillsto carry out TDG activities as required by the Clear Language Regulations. For Dangerous Goodsentering or leaving the site (the Controlled Area): Receive / Handle / Ship / Transport. Issued withsuccessful completion of the training, is a certificate, which must be available (i.e. in your pocket) whencarrying out a TDG activity. Supervisors need to be aware that TDG regulations require that thisqualification be removed any time the person is incapable of completing the regulation prescribed


12617 CLASS 2 - ORDER PICKER OPERATION-RAYMOND BND N Y

MODEL 162Qualification for Knowledge & Skills required for the safe/efficient operation of the Raymond Order Picker.



7143 JPM ELECTRIC MOTOR RIDER TRUCKS BND FIELD 2 hour(s) 24 QClass 1: Electric Motor Rider Trucks practical testing. Three Wheel Electric Trucks, Sit-Down Lift Code4 and Counterbalanced Rider Type, pneumatic/Cushion Tire, Sit-Down (Includes High And LowPlatform) Lift Code 5

7144 JPM ELECTRIC MOTOR NARROW AISLE TRUCKS BND FIELD 2 hour(s) 24 Q Electric Motor Narrow Aisle Trucks practical testing.LIFT CODE TYPE OF EQUIPMENT 1HighLift Straddle 2 Order Picker 3 Reach Type Outrigger 4 Sideloaders5 Swing Mast

6 Turret Trucks - Man on Board 7 Turret Trucks - Ground Level

62361 CRS FALL PROTECTION SYSTEMS THEORY & BND CLASSROOM 6 hour(s)PRACTICAL

Demonstrate knowledge and correct application of fall arrest equipment and systems in compliance withall legal standards and Bruce Power proceduresGives a credit in 7235 (classroom) & 7236 (practical)

3839 JPM ORDER PICKER OPERATION-RAYMOND MOD.# 162 BND FIELD 4 hour(s) 24QThis course provides the knowledge & skills training required to perform the tasks associated with CM-2Stockkeeper job stream. It reflects the Job Performance Measures that must be successfully completed toobtain a credit in the course.Knowledge & Skills required for the safe/efficient operation of theRaymond Order Picker


12618 CLASS 2 - SWING REACH OPERATION- RAYMOND BND N Y

MODEL 537Qualification for Knowledge & Skills required for the safe/efficient operation of the Raymond Swing Reach




TQD-00001 R001


Page 18


7143 JPM ELECTRIC MOTOR RIDER TRUCKS BND FIELD 2 hour(s) 24 QClass 1: Electric Motor Rider Trucks practical testing. Three Wheel Electric Trucks, Sit-Down Lift Code4 and Counterbalanced Rider Type, pneumatic/Cushion Tire, Sit-Down (Includes High And LowPlatform) Lift Code 5

7144 JPM ELECTRIC MOTOR NARROW AISLE TRUCKS BND FIELD 2 hour(s) 24 Q Electric Motor Narrow Aisle Trucks practical testing.LIFT CODE TYPE OF EQUIPMENT 1HighLift Straddle 2 Order Picker 3 Reach Type Outrigger 4 Sideloaders5 Swing Mast

6 Turret Trucks - Man on Board 7 Turret Trucks - Ground Level

62361 CRS FALL PROTECTION SYSTEMS THEORY & BND CLASSROOM 6 hour(s)PRACTICAL

Demonstrate knowledge and correct application of fall arrest equipment and systems in compliance withall legal standards and Bruce Power proceduresGives a credit in 7235 (classroom) & 7236 (practical)

3839 JPM ORDER PICKER OPERATION-RAYMOND MOD.# 162 BND FIELD 4 hour(s) 24QThis course provides the knowledge & skills training required to perform the tasks associated with CM-2Stockkeeper job stream. It reflects the Job Performance Measures that must be successfully completed toobtain a credit in the course.Knowledge & Skills required for the safe/efficient operation of theRaymond Order Picker

3840 JPM SWING REACH OPERATION- RAYMOND MOD.# 537 BND FIELD 4 hour(s) 24QThis course provides the knowledge & skills training required to perform the tasks associated with CM-2Stockkeeper job stream. It reflects the Job Performance Measures that must be successfully completed toobtain a credit in the course.Knowledge & Skills required for the Safe/Efficient Operation of theRaymond Swing Reach

Emergency MeasuresQual Id Name Location Critical? Auto Cert. Revert To

12097 FIRE RESPONSE FOR STAFF ON ROUNDS BND N YThis qualification is intended for staffs who regularly complete rounds or investigate problems in the stations.Typically Operators and Security.The qualification includes the Fire Extinguisher course.


7048 CRS FIRE EXTINGUISHER PRACTICAL BND FIELD 4 hour(s) 36 DThe theory and practical applications of fire extinguisher.


12019 FIRE WATCH - CONTROL OF IGNITION SOURCES BND N YKnowledge and skills required to meet responsibilities under the Control of Ignition Sources procedure


7048 CRS FIRE EXTINGUISHER PRACTICAL BND FIELD 4 hour(s) 36 DThe theory and practical applications of fire extinguisher.

63304 CRS FIRE WATCH - CONTROL OF IGNITION BND CLASSROOM 1 day(s) 36 QSOURCES

Knowledge and skills required to meet responsibilities under the Control of Ignition Sources procedure(BP-PROC-00159)


388 FIRST AID - EMERGENCY BND N N




TQD-00001 R001


Page 19



1601 FIRST AID - STANDARD BND N Y


6665 CRS FIRST AID - EMERGENCY BND CLASSROOM 2 day(s) 36 DCertification to St. John Ambulance standards in Standard First Aid. Intended for BEST members and building first aid people per OHSA Regulation 1101

Fall ProtectionQual Id Name Location Critical? Auto Cert. Revert To

1059 FALL PROTECTION EQUIPMENT INSPECTOR BND Y NThis qualification is required by all staff assigned to regularly inspect fall protection equipment.


6959 CRS FALL ARREST EQUIPMENT INSPECTION BND SHOP 1 day(s) 36 QThis course is to train and certify inspectors of Fall Arrest equipment. This course is provided by anexternal contractor either Andrew Sulowski Fall Protection or Practical Solutions Int.


1589 FALL PROTECTION QUALIFIED BND N NThis qualification is required for all staff who will be working at a required task presenting a hazard of falling adistance greater than three (3) metres to the next safe level. Per BP-SM-00001, Fall Protection.It covers thecorrect theory and use of Fall Arrest Systems (FAS). A FAS is an assembly of components joined together sothat when the assembly is connected to a fixed support, it is capable of arresting a worker’s accidental fall.Correct use of a fall arrest system greatly reduces risk of injury in the event of a fall; however, it does not


7235 CRS FALL PROTECTION SYSTEM THEORY BNPD BND CLASSROOM 4 hour(s)Demonstrate correct application of fall arrest equipment and systems in compliance with all legal

7236 JPM FALL PROTECTION SYS. PRACTICAL BNPD BND FIELD 2 hour(s) 36 Q

This is the practical portion of the "Fall Protection Systems" course. Candidates will be required to doand demonstrate use of fall protection systems and equipment.

ISRSQual Id Name Location Critical? Auto Cert. Revert To

3001 ISRS AUDITOR BND N NThis qualification is required by individuals assigned to conduct ISRS Loss Control audits. In addition to thetraining requirements specified here, individuals are required to conduct an audit under the guidance of a qualifiedDNV ISRS qualified auditor.


1369 CRS ACCREDITED SAFETY AUDITOR - ISRS BND VENDOR 5 day(s)This course provides participants with a consistent approach to safety management uditing using provenauditing techniques and concepts.Class participants will gain audit experience in a simulation exercisedesigned to provide skills in auditing and report writing. This training is one of the requirements forbecoming an Accredited Safety Auditor.

6791 CRS MODERN SAFETY MANAGEMENT OHN VENDOR 4 day(s)This course covers all aspects of Loss Control. The course teaches complete understanding of theprinciples & concepts of Loss Control, & its relationship to the measurement system of the InternationalSafety Rating System (ISRS).


TQD-00001 R001


Page 20


MedicalsQual Id Name Location Critical? Auto Cert. Revert To

1767 NOISE EXPOSED INDIVIDUALS BND N NQualification tracks individuals who require regular hearing tests. Testing is administered by Health Services.


29543 ARQ MEDICAL - HEARING TEST BND 2 hour(s) 24 DAudiogram for people who are noise exposed.This is an administrative requirement. Medical servicesperforms the testing and provides the credit input.

OH&SAQual Id Name Location Critical? Auto Cert. Revert To

6108 JH&S COMMITTEE MEMBER BND N YThis qualification is required by all employees who have been selected to serve on a JH&S committee.

6943 CRS JHSC BASIC CERTIFICATION BND CLASSROOM 4 day(s)Joint Health & Safety Committee Basic Certification. This course is for JH&SC certified members under Federal Legislation to become certified JH&SC members under Provincial Legislation.

60592 CRS JHSC WORKPLACE HAZARD SPECIFIC BND CLASSROOM 5 day(s)This course is the 2nd part of the Certification training required for Joint Health and Safety Committee(JHSC) members.


10232 JH&S COMMITTEE MEMBER - BTU BND N N


61814 CRS CONSTRUCTION TRADES SECTOR SPECIFIC BND VENDOR 5 day(s)TRAINING - PART 2

For the BTU JHSC members. Workplace Hazard Specific Training Program for Construction Trades due to the transient nature of their work. They are using Sector Specific Training instead for their Part 2requirement.Their Part 2 training is provided to them by the Construction Safety Association of Ontarioit consists of the following Modules;· Helicopter Lifting· Confined Spaces in Construction· Hoistingand Rigging Crane Hazards· Trenching Hazards· Traffic Control & Backing Vehicles· EquipmentHazards· Electrical Hazards· Manual Material Handling· Working at Heights· Formwork· WorkersTrades Committees· Dust and Fibres

6943 CRS JHSC BASIC CERTIFICATION BND CLASSROOM 4 day(s)Joint Health & Safety Committee Basic Certification. This course is for JH&SC certified members under Federal Legislation to become certified JH&SC members under Provincial Legislation.

63997 CRS CONSTRUCTION TRADES - SIMULATED HAZARD BND CLASSROOM 3 day(s)ANALYSIS

For BTU JHSC members Delivered by Construction Safety Association of Ontariowww.csao.orgThis program is one of three components of the Construction Certification Program.Upon completion, participants will be able to prepare for and conduct a workplace hazard analysis,as well as a health and safety plan assessment for a typical construction workplace. Modulesinclude: Review of previous health and safety programs JHSC structures/powers Certifiedmembers' roles/powers Dangers and hazardous circumstances review Jobsite inspections andrecommendations The program takes 3 days to complete. Participants must have completed theConstruction Health and Safety Representative Program or its equivalent, as well as theSector-Specific Certification Program. The maximum class size is 20 participants


TQD-00001 R001


Page 21


Respiratory ProtectionQual Id Name Location Critical? Auto Cert. Revert To

10472 ADVANTAGE 200LS AIR PURIFYING RESPIRATOR BND N N

(MSA) - FOR WELDERS ONLYThe Advantage 200LS air purifying respirator by MSA. This respirator is designed to fit under a welders faceshield and is intended for WELDERS ONLY


62720 ARQ MEDICAL - COMPLETE FORM-11767, BND 1 hour(s) 12 DEMPLOYEE HEALTH SCREENING REQUEST

This administrative requirement is used to trigger an annual medical screening. After completingFORM-11767 with your supervisor contact your local Health Services office to arrange for a visit. Atthis visit the form will be completed and any necessary medicals will be completed.Medicals requiredwill be based on the information provided on the Screening form and a TIMS report.

24643 ARQ MEDICAL - RESPIRATORY MEDICAL BND 1 hour(s) 12 DASSESSMENT - NON SCBA

This is a requirement of the respiratory protection program and must be completed before annual training or fit testing can be completed.

7016 EXM RESPIRATORY PROTECTION BND CLASSROOM 4 hour(s) 12 DREQUALIFICATION

Training on the selection, care and use of air-purify, air-supplied and self contained respiratory

7013 CRS RESPIRATORY PROTECTION BND CLASSROOM 4 hour(s)Theory and practical training on the selection, care and use of air-purifying, air-supplied and selfcontained respiratory protection.

62149 ARQ FIT TEST - ADVANTAGE 200LS - MSA -FOR BND FIELD 1 hour(s) 12 DWELDERS ONLY

This fit test is for the successful donning, pre-use testing and fit testing of the Advantage 200LS airpurifying respirator. This respirator is designed to fit under a welders face shield.


11537 BULLARD AIRLINE RESPIRATOR BND N YThis qualification is required by all staff who are required to wear the Bullard Series 88VX airline respirator in thecourse of their work. The Bullard 88VX series airline respirator provides respiratory protection for abrasive blasters and painters and consists of three components, respirator helmet assembly, breathing tube assembly and airsupply hose. The Bullard is a loose fitting respirator so a fit testing is not required









5270 FULL FACE AIR PURIFYING RESPIRATOR (MSA) BND Y YThis qualifcation is required by all staff who are required to wear a full face air purifying respirator manufactured


TQD-00001 R001


Page 22


by MSA in the course of their work. Full-Face, air-purifying negative proessure. For the MSA Ultra Twin.


24126 ARQ FIT TEST - FULL FACE MASK - ULTRA TWIN BND FIELD 4 hour(s) 12 DThis P/E is required by all individuals who require Respiratory Protection using an air-purifying,negativepressure full-face respirator MSA Model Ultra Twin in the course of their duties.









5277 FULL FACE AIR SUPPLIED RESPIRATOR (ISI) BND Y YThis qualifcation is required by all staff who are required to wear a full face air supplied respirator manufacturedby ISI in the course of their work. Supplied air, full face mask. For Panaseal full face mask, ARAP-C - ISI.


24135 ARQ FIT TEST - FULL FACE MASK - ISI PANASEAL BND FIELD 4 hour(s) 12 DThis fit test is required by all individuals who require Respiratory Protection using an air-supplied full faceMask ISI Panaseal full face mask in the course of their duties. in the course of their duties.









5268 HALF MASK AIR PURIFYING RESPIRATOR ( MSA) BND Y YThis qualifcation is required by all staff who are required to wear a half mask air purifying respirator manufactured by MSA in the course of their work. Half-mask, air-purifying negative pressure. For Comfo II and Comfo




TQD-00001 R001


Page 23


24124 ARQ FIT TEST - HALF MASK COMFO - CLASSIC AND COMFOII BND FIELD 4 hour(s) 12 DThis fit test is required by all individuals who require Respiratory Protection using an air-purifying negativepressure half mask respirator MSA Model Comfo Classic or Comfo ll in the course of their duties.








5273 HALF MASK AIR SUPPLIED RESPIRATOR (US SAFETY)BND Y YThis qualifcation is required by all staff who are required to wear a half mask air supplied respirator manufacturedby US Safety in the course of their work. Supplied air, full face mask. For US Safety 1520H & 152 modified.



24129 ARQ FIT TEST - HALF MASK-1520H BND FIELD 4 hour(s) 12 DThis fit test is required by all individuals who require Respiratory Protection using an air supplied half maskU.S. Safety Model 1520H in the course of their duties.








12477 N95 DUST MASK PARTICULATE RESPIRATOR - BIOLOGICAL BND N Y

PROTECTIONThis qualification is for Health Services and Medical Emergency Responders ONLY. For use when an N95disposable mask is used for biological particulate protection.


63834 ARQ FIT TEST - N95 DUST MASK BND 1 hour(s) 12 YThis fit test is for the successful donning, pre-use testing and fit testing of the North Disposable airpurifying particulate respirator





TQD-00001 R001


Page 24







11577 PC 4 GAS MASK - SECURITY ONLY BND Y YThis Gas Mask is for Security use only.The mask had to meet a design criterion of 6667 and 5884 when wornwith spectacles. The design criterion is based on the NATO standard for NBC masks.


62767 ARQ FIT TEST - PC 4 GAS MASK - SECURITY ONLY BND 1 hour(s) 12 DThis Gas Mask is for Security use only.This "fit test" is for the successful donning, pre-use testingand fit testing of the PC 4 Gas Mask respirator.The mask had to meet a design criterion of 6667 and5884 when worn with spectacles. The design criterion is based on the NATO standard for NBC masks









11657 PLASTIC SUIT - RESPIRATORY PROTECTION BND Y YThis qualification is required by all staff to wear plastic suits. Plastic suits are considered respiratory protectionand as such fall under the requirements of BP-SM-0030 and CSA Z94.4







62731 ARQ MEDICAL - PLASTIC SUITS BND 12 DUsed by Health Services to track staff who wear plastics - part of the respiratory protection programSee BP-SM-00030 Requirements For Respiratory Protection and CSA Standard 94.4-02


TQD-00001 R001


Page 25



5272 POWERED AIR PURIFYING RESPIRATOR (3M) BND Y YThis qualifcation is required by all staff who are required to wear a powered air purifying respirator manufacturedby 3M in the course of their work. Powered air-purifying. For 3M 7800



24128 ARQ FIT TEST - PAPR - 3M RESPIRATOR OHN FIELD 4 hour(s) 12 DThis fit test is required by all individuals who require Respiratory Protection using a Powered air purifyingrespirator 3M Model 7800 in the course of their duties.








5271 POWERED AIR PURIFYING RESPIRATOR (MSA) BND Y YThis is required by all individuals who require Respiratory Protection using a Powered air-purifying respirator MSAModel Optimair 6A equipped with a comfo half-mask in the course of their duties



24127 ARQ FIT TEST - PAPR - MSA BND FIELD 4 hour(s) 12 DThis is required by all individuals who require Respiratory Protection using a Powered air-purifyingrespirator MSA Model Optimair 6A equipped with a comfo half-mask in the course of their duties








11717 RAM’S HORN CONTINUOUS AIR SUPPLY RESPIRATORBND Y YRam's Horn’s classified as a Loose Fitting Respirator - Comes with a belt and is worn around the neck. Thisrespirator delivers a continuous supply of air to the user and is usually worn with a tyvek hood. This respiratordoes not require a fit test.


TQD-00001 R001


Page 26











5279 SCBA RESPIRATOR (ISI) BND Y YThis qualifcation is required by all staff who are required to wear SCBA manufactured by ISI in the course of their work. SCBA open circuit. For ISI Magnum



24135 ARQ FIT TEST - FULL FACE MASK - ISI PANASEAL BND FIELD 4 hour(s) 12 DThis fit test is required by all individuals who require Respiratory Protection using an air-supplied full faceMask ISI Panaseal full face mask in the course of their duties.

23783 ARQ MEDICAL - RESPIRATOR MEDICAL BND 1 hour(s) 12 DASSESSMENT - SCBA







5280 SCBA RESPIRATOR VIKING - ERT ONLY BND Y YThis qualifcation is required by all staff who are required to wear SCBA manufactured by MSA in the course oftheir work. SCBA (open circuit) Viking with Airswitch mask



23783 ARQ MEDICAL - RESPIRATOR MEDICAL BND 1 hour(s) 12 DASSESSMENT - SCBA


62720 ARQ MEDICAL - COMPLETE FORM-11767, BND 1 hour(s) 12 D


TQD-00001 R001


Page 27


EMPLOYEE HEALTH SCREENING REQUESTThis administrative requirement is used to trigger an annual medical screening. After completingFORM-11767 with your supervisor contact your local Health Services office to arrange for a visit. Atthis visit the form will be completed and any necessary medicals will be completed.Medicals requiredwill be based on the information provided on the Screening form and a TIMS report.



24139 ARQ FIT TEST - SCBA - VIKING BND FIELD 4 hour(s) 12 DThis fit test is required by all individuals who require Respiratory Protection using SCBA ISI Model Vikingwith Airswitch mask in the course of their duties.


11638 SPEEDGLAS WELDING HELMET POWERED AIR PURIFYING BND N Y

RESPIRATOR (PAPR) - HORNELL ADFLOThis respirator is used for various welding jobs and has a welding plate built into the helmet. It operates with amotor and battery pack which is also equipped with a High efficiency particulate filter.










12077 SUPERVISORS RESPIRATORY PROTECTION KNOWLEDGE BND N Y

This qualification is for supervisors of staff who use respiratory protection.As required by PB-SM-00030,Requirements For Respiratory Protection and CSA Standard Z94.4-02, Selection, Use and Care of Respirators

PEL ID Type Name Location Envir Duration Requal



11637 ULTRAVUE FULL FACE POWERED AIR PURIFYING RESPIRATOR BND NY

(PAPR) - MSAThis respirator is used for various type 3 asbestos work and other work where required. It operates with a motor and battery pack which is also equipped with a High efficiency particulate filter.





TQD-00001 R001


Page 28







62966 ARQ FIT TEST - ULTRAVUE FULL FACE POWERED BND 1 hour(s) 12 DAIR PURIFYING RESPIRATOR (PAPR) - MSA

This respirator is used for various type 3 asbestos work and other work where required. It operates with a motor and battery pack which is also equipped with a High efficiency particulate filter.

Safety AwarenessQual Id Name Location Critical? Auto Cert. Revert To

1277 AWARENESS FOR SUPERVISOR OF WORKER ENTERING BND Y N

AN ACAAs defined by BP-SM-00048, Conventional Safety Guidelines for Access Controlled Areas.


6994 ARQ ACCESS CONTROLLED AREA - WORKER BNDCredit is received when a signed copy of Appendix B of BP-SM-0048 is received with option C checkedoff. The employee should be linked to qual 2418 at the time credit is given.

6996 ARQ ACCESS CONTROLLED AREA - SUPERVISOR BNDCredit is received when a signed copy of Appendix B of BP-SM-0048 is received with option D checkedoff. The employee should be linked to qual 1277 at the time credit is given.


1298 ACCESS CONTROL DESK ATTENDANT AWARENESS BND Y N

FOR ENTERING AN ACAAs defined by BP-SM-00048, Conventional Safety Guidelines for Access Controlled Areas.



6995 ARQ ACCESS CONTROL DESK ATTENDANT AWARENESSBNDCredit is received when a signed copy of Appendix B of BP-SM-0048 is received with option B checkedoff. The employee should be linked to qual 1298 at the time credit is given.


2402 VAULT COORDINATOR AWARENESS FOR ENTERING AN ACA BND Y NAs defined by BP-SM-00048, Conventional Safety Guidelines for Access Controlled Areas.



6995 ARQ ACCESS CONTROL DESK ATTENDANT AWARENESS BNDCredit is received when a signed copy of Appendix B of BP-SM-0048 is received with option B checkedoff. The employee should be linked to qual 1298 at the time credit is given.

6997 ARQ ACCESS CONTROLLED AREA - VAULT BND


TQD-00001 R001


Page 29


COORDINATORCredit is received when a signed copy of Appendix B of BP-SM-0048 is received with option A checkedoff. The employee should be linked to qual 2402 at the time credit is given.


2418 WORKER AWARENESS FOR ENTERING AN ACA BND Y NAs defined by BP-SM-00048, Conventional Safety Guidelines for Access Controlled Areas.




12357 HEALTH AND SAFETY LAW BND N YAs an Bruce Power supervisor, promote, create and maintain a safe workplace environment by being proactive indemonstrating supervisory responsibilities to the standards of Bruce Power and as prescribed by the Occupational Health and Safety Act and its associated Regulations.


6716 CRS HEALTH & SAFETY LAW BND CLASSROOM 6 hour(s)An introduction and hands on examination of the requirements of a supervisor as prescribed by theOccupational Health and Safety Act and its associated Regulations.


12017 INDUSTRIAL ERGONOMIC RISK ASSESSOR BND N YQualification for Industrial Ergonomic Risk Assessor


62427 CRS EVALUATING INDUSTRIAL ERGONOMIC RISKS BND CLASSROOM 2 day(s)An overview of the theory of the causation of Workplace Musculo-Skeletal Disorders (WMSD’s), followed by a thorough coverage of the ergonomic risk factors associated with industrial workplaces. This course gives the student the tools necessary to evaluate these risk factors as well as the skills necessary tooffer possible solutions to identified problems.2 full days of classes with 3-6 hours of practicalevaluations (outside of the class) scheduled at a time agreed upon by the student and instructor.

63219 JPM EVALUATING INDUSTRIAL ERGONOMIC RISK BND CLASSROOM 4 hour(s) 36 QJPM

A JPM to demonstrate effective assessment of industrial ergonomic risks following successfulcompletion of 62427 - EVALUATING INDUSTRIAL ERGONOMIC RISKS. Evaluation by Bruce Power

63302 ARQ INDUSTRIAL ERGONOMIC CONTINUING BND 4 hour(s) 36 QTRAINING WORKSHOP

Workshop to bring qualified industrial ergonomic assessor up-to-date on current practices in the field.Content to be determined by Industrial Ergonomist


12018 OFFICE ERGONOMIC RISK ASSESSOR BND N YQualification for Office Ergonomic Risk Assessor


62427 CRS EVALUATING INDUSTRIAL ERGONOMIC RISKS BND CLASSROOM 2 day(s)An overview of the theory of the causation of Workplace Musculo-Skeletal Disorders (WMSD’s), followed by a thorough coverage of the ergonomic risk factors associated with industrial workplaces. This course gives the student the tools necessary to evaluate these risk factors as well as the skills necessary tooffer possible solutions to identified problems.2 full days of classes with 3-6 hours of practicalevaluations (outside of the class) scheduled at a time agreed upon by the student and instructor.

61555 ARQ ERGONOMICS EMPLOYEE ASSESSMENT BND 1 hour(s)This Administrative Requirement is used to tack the completion of an Ergonomic Assessment of anEmployee at their workstation. A credit is entered each time an assessment has been completed.Thefirst assessment is normally associated with successful completion of 6880 - Ergonomics Employee


TQD-00001 R001


Page 30


Assessment.

63303 ARQ OFFICE ERGONOMIC CONTINUING TRAINING BND 4 hour(s) 36 QWORKSHOP

Workshop to bring qualified office ergonomic assessor up-to-date on current practices in the field.Content to be determined by Industrial Ergonomist


12237 SEWAGE BIO-HAZARD EXPOSURE BND N YHolder is permitted contact with systems containing sewage or other bio-hazards


63369 ARQ SEWAGE AND WASTEWATER WORKER BND 1 hour(s)An orientation for Sewage and Wastewater Workers, can be given by supervisor but need to include avisit to Health Services and should be checked on Form-11767, Employee Health Screening Request.Biological Hazards in Sewage and Wastewater, Controlling Risk to WorkersWho is at Risk?Workerswhose activities bring them into contact with sewage, sewage products or wastewater are at risk ofcontacting a work related-illness. The majority of illnesses are relatively mild cases of gastroenteritis,but potentially more serious diseases, such as leptospirosis (Weil’ disease) and hepatitis can occur.The most common way for infection to occur is by hand-to-mouth contact eating, drinking, smoking, orwiping the face with contaminated hands or gloves. Some organisms can enter the body though theeyes, nose and mouth.Breathing in contaminated dust, aerosol or mist can cause infection.Additional InformationBP-PROC-00113 Safe Sewage Handling

62727 ARQ MEDICAL - SEWAGE WORKER BNDUsed by Health Services to track workers who are or maybe exposed to sewage


2803 SWITCHYARD SAFETY AWARENESS BND N NThis is a safety awareness qualification for unsupervised (non-operator) staff needing to enter and work in theswitchyard. Hydro One determines the safety requirements and training requirements for entering switchyards.


22123 CRS SWITCHYARD SAFETY REFRESHER BND VENDOR 4 hour(s) 36 DThis is a safety awareness refresher training for unsupervised Unit 0 non-authorized operators working inthe switchyard.

2562 CRS SWITCHYARD SAFETY AWARENESS BND VENDOR 1 day(s)This is a safety awareness training for unsupervised Unit 0 non-authorized operators working in the switchyard. Hydro One provides the instructor to deliver this training. Bruce Powerprovides individual to input the credits



TQD-00001 R001


Page 31


APPENDIX 4: PREREQUISITE QUALIFICATIONS OF SPECIFIC QUALIFICATIONS

There are no prerequisite qualifications associated with an qualification in this TQD.


TQD-00001 R001


Page 32


APPENDIX 5: PROGRAM ELEMENT PREREQUISITES

PEL Id Type Location

1369 CRS ACCREDITED SAFETY AUDITOR - ISRS BNDPrereq. PEL ID Type Name

6791 CRS MODERN SAFETY MANAGEMENT OHN

6688 CRS CONFINED SPACE COORD.-REQUAL. BNDPrereq. PEL ID Type Name

6663 CRS CONFINED SPACE - COORDINATOR BND

7016 EXM RESPIRATORY PROTECTION REQUALIFICATION BNDPrereq. PEL ID Type Name

7013 CRS RESPIRATORY PROTECTION BND

7131 CRS VEHICLE HANDLING (FIELD) BNDPrereq. PEL ID Type Name

7125 CRS COACHING EXPERIENCED DRIVERS. (LIGHT VEHICLES) BND

7150 JPM ELEVATING WORK PLATFORM-ROLLING BND

Prereq. PEL ID Type Name

7119 CRS ELEVATING WORK PLATFORM BND

7151 JPM ELEVATING WORK PLATFORM - ON SLAB -SELF PROPELLED BNDPrereq. PEL ID Type Name


7153 JPM ELEVATING WORK PLATFORM - OFF SLAB -SELF PROPELLED BNDPrereq. PEL ID Type Name


7155 JPM ELEVATING WORK PLATFORM-BOOM-TYPE BNDPrereq. PEL ID Type Name


60592 CRS JHSC WORKPLACE HAZARD SPECIFIC BNDPrereq. PEL ID Type Name

6943 CRS JHSC BASIC CERTIFICATION BND

62465 CRS WORKING WITH ASBESTOS - CBT BNDPrereq. PEL ID Type Name

7009 CRS WHMIS - CBT BND

62491 CRS ISRS UPDATE/REVIEW TRAINING - SENIOR MANAGERS BNDPrereq. PEL ID Type Name

6791 CRS MODERN SAFETY MANAGEMENT OHN

63219 JPM EVALUATING INDUSTRIAL ERGONOMIC RISK JPM BNDPrereq. PEL ID Type Name

62427 CRS EVALUATING INDUSTRIAL ERGONOMIC RISKS BND

63298 CRS ISRS AUDITOR COURSE BNDPrereq. PEL ID Type Name

14297 CRS AUDITOR TRAINING BND

63299 JPM ISRS AUDITOR - JPM BNDPrereq. PEL ID Type Name

63298 CRS ISRS AUDITOR COURSE BND


TQD-00001 R001


Page 33


APPENDIX 6: PROGRAM GROUPS

PEL Id Type Location Create Master

2562 CRS SWITCHYARD SAFETY AWARENESS BND N

Sub PEL ID Type Name22123 CRS SWITCHYARD SAFETY REFRESHER BND

6654 CRS CONFINED SPACE - MONITOR INITIAL/REQUAL BND N

Sub PEL ID Type Name6653 CRS CONFINED SPACE - ENTRY INITIAL/REQUAL BND

6655 CRS CONFINED SPACE - SURVEYOR INITIAL/REQUAL BND N

Sub PEL ID Type Name6653 CRS CONFINED SPACE - ENTRY INITIAL/REQUAL BND6654 CRS CONFINED SPACE - MONITOR INITIAL/REQUAL BND

6663 CRS CONFINED SPACE - COORDINATOR BND N

Sub PEL ID Type Name6653 CRS CONFINED SPACE - ENTRY INITIAL/REQUAL BND6654 CRS CONFINED SPACE - MONITOR INITIAL/REQUAL BND6655 CRS CONFINED SPACE - SURVEYOR INITIAL/REQUAL BND6688 CRS CONFINED SPACE COORD.-REQUAL. BND

6688 CRS CONFINED SPACE COORD.-REQUAL. BND N

Sub PEL ID Type Name6653 CRS CONFINED SPACE - ENTRY INITIAL/REQUAL BND6654 CRS CONFINED SPACE - MONITOR INITIAL/REQUAL BND6655 CRS CONFINED SPACE - SURVEYOR INITIAL/REQUAL BND

6943 CRS JHSC BASIC CERTIFICATION BND N

Sub PEL ID Type Name6716 CRS HEALTH & SAFETY LAW BND

7009 CRS WHMIS - CBT BND N

Sub PEL ID Type Name7023 CRS ASBESTOS AWARENESS BND

7013 CRS RESPIRATORY PROTECTION BND N

Sub PEL ID Type Name7016 EXM RESPIRATORY PROTECTION REQUALIFICATION BND

7123 CRS VEHICLE HANDLING DEFENSIVE DRIVING COURSE BND NSub PEL ID Type Name


7127 CRS VEHICLE HANDLING PROFESSIONAL DRIVER IMPROVEMENT COURSE BND NSub PEL ID Type Name


61563 CRS WHMIS - CLASSROOM BND N

Sub PEL ID Type Name7023 CRS ASBESTOS AWARENESS BND7009 CRS WHMIS - CBT BND

61618 CRS INDUCTION TRAINING BND N

Sub PEL ID Type Name6994 ARQ ACCESS CONTROLLED AREA - WORKER BND3874 CRS ENVIRONMENTAL QUALIFICATION FOR MAINTAINERS & OPERATORS - CBT BND5248 CRS CONDUCT OF MTCE EXAM - MTCE STAFF - CBT BND5461 CRS FOREIGN MATERIAL EXCLUSION BND6526 CRS JOB SAFETY ANALYSIS BND6653 CRS CONFINED SPACE - ENTRY INITIAL/REQUAL BND6654 CRS CONFINED SPACE - MONITOR INITIAL/REQUAL BND6717 CRS SAFETY AWARENESS INTRODUCTION - CBT BND


TQD-00001 R001


Page 34


6923 CRS BRUCE GENERAL EMPLOYEE EMERGENCY RESPONSE - CBT BND6945 CRS WORK PROTECTION PROGRAM INTRODUCTION - CBT BND62715 ARQ WORK PROTECTION - LOCKOUT INTRODUCTION BND6966 CRS ELECTRICAL AWARENESS PRESENTATION BND7009 CRS WHMIS - CBT BND7023 CRS ASBESTOS AWARENESS BND24163 CRS WPP - LEVEL 2 WORK PROTECTION PROCEDURES - WORKER BND24165 EXM WPP - WORK PROTECTION PROCEDURES WORKER - CBT BND27383 CRS WPP - WORKER REQUALIFICATION - CBT BND28086 ARQ AIRLOCK OPERATION VIDEO B5-8 B5-860273 ARQ H2 AWARENESS PRESENTATION BND61507 CRS EVENT FREE TOOLS INTRODUCTION BND6991 CRS ENVIRONMENTAL AWARENESS - CBT BND

62241 JPM COMPETENT SUPERVISOR - BTU BND N

Sub PEL ID Type Name63655 ARQ COMPETENT SUPERVISOR - BTU REQUALIFICATION BND

62361 CRS FALL PROTECTION SYSTEMS THEORY & PRACTICAL BND N

Sub PEL ID Type Name7236 JPM FALL PROTECTION SYS. PRACTICAL BNPD BND7235 CRS FALL PROTECTION SYSTEM THEORY BNPD BND

63112 CRS GET IN CLASSROOM + WORK PROTECTION WORKER BND N

Sub PEL ID Type Name6945 CRS WORK PROTECTION PROGRAM INTRODUCTION - CBT BND6991 CRS ENVIRONMENTAL AWARENESS - CBT BND7009 CRS WHMIS - CBT BND7023 CRS ASBESTOS AWARENESS BND24163 CRS WPP - LEVEL 2 WORK PROTECTION PROCEDURES - WORKER BND24165 EXM WPP - WORK PROTECTION PROCEDURES WORKER - CBT BND62715 ARQ WORK PROTECTION - LOCKOUT INTRODUCTION BND

63219 JPM EVALUATING INDUSTRIAL ERGONOMIC RISK JPM BND N

Sub PEL ID Type Name63302 ARQ INDUSTRIAL ERGONOMIC CONTINUING TRAINING WORKSHOP BND


TQD-00001 R001


Page 35


APPENDIX 7: PERSONAL DEVELOPMENT PROGRAM ELEMENTS

JHSC MemberIn addition to the qualifications offered in this TQD the following are suggested continuingtraining opportunities for JHSC Members

PEL ID Type Name Duration Envir Location

5203 CRS APPARENT CAUSE EVALUATION - CBT 4 hour(s) CBT BNDPrepares the trainee to perform Apparent Cause Evaluation to address a Resolution Category C StationCondition Record (SCR). Barrier Analysis is used as the analytical tool.

27744 CRS HAZARD RECOGNITION & CONTROL VENDOR BNDIntroduces the techniques of hazard recognition & control and examines specific hazards - primarily of aphysical & safety nature. Hazard recognition & control are shown to be inter-related as the non-existence orinadequacies of control measures in themselves may constitute hazards subject to the techniques of hazardrecognition.Available from Ryerson Polytechnical University, Toronto, Canada as course COHS608.

61500 ARQ LOSS CONTROL LEADERSHIP ORIENTATION/INDUCTION TEST - CBT 4 hour(s) BNDAll Line management personnel are required to receive Loss Control Leadership Orientation/Induction Training.This will be accomplished through required reading assigment of the Practical Loss Control Leadership Mnaualfollowed by a successful completion of a CBT checkout. Exemptions to this requirement will be granted tothose personnel who have received ISRS awareness training from IAPA in the past.

61507 CRS EVENT FREE TOOLS INTRODUCTION 4 hour(s) CLASSROOM BNDThis workshop provides the participant with a introduction to the Event Free Tools used by Bruce Power staff.Self-Check, Pre-Job Briefing, Questioning Attitude, Conservative Approach, 3 - Way Communications andProcedural Use & Adherence.

62427 CRS EVALUATING INDUSTRIAL ERGONOMIC RISKS 2 day(s) CLASSROOM BNDAn overview of the theory of the causation of Workplace Musculo-Skeletal Disorders (WMSD’s), followed by athorough coverage of the ergonomic risk factors associated with industrial workplaces. This course gives thestudent the tools necessary to evaluate these risk factors as well as the skills necessary to offer possiblesolutions to identified problems.2 full days of classes with 3-6 hours of practical evaluations (outside of theclass) scheduled at a time agreed upon by the student and instructor.

62461 ARQ FIRE & BUILDING CODE/REGULATION REVIEW 2.5 BNDProvided by a contractor for JH&SC members

63009 ARQ OCCUPATIONAL HEALTH AND SAFETY - MEASUREMENT AND ANALYSIS BNDUsed to track successful completion of this Ryerson Course.This course is designed to introduce theterminology, concepts, equipment, and techniques of occupational health and safety measurement andanalysis. Topics covered include occupational hygiene, air sampling, data evaluation, biological sampling, andthe assessment of heat stress, noise, vibration, radiation, illumination, and ventilation systems. Available fromRyerson University, Toronto, Canada as course COHS217.

From Ryerson University, Toronto Occupational Health and Safety Certificate ProgramOther than 63009 these courses are not in TIMS. See www.ryerson.ca for additionalinformation. Courses offered include, most are available through distant education:

CCMN114 Communication: Short Management ReportsCOHS208 Occupational Health: Occupational Health and Safety LawCOHS508 Occupational Health: Occupational HealthCOHS608 Occupational Health: Hazard Recognition and ControlCVOH215 Occupational Health: Occupational Health and Safety SystemsCVOH217 Occupational Health: Measurement and AnalysisCVOH221 Occupational Health: Topics in Occupational Health and SafetyCINT905 Interdisciplinary Studies: Conflict Resolution and Dispute NegotiationCMHR405 Human Resources: Organizational Behaviour and Interpersonal SkillsCOHS477 Occupational Health: Integrated Disability ManagementCOHS777 Occupational Health: Workers Compensation ManagementCPPA322 Public Administration: Understanding Canadian Public Administration


TQD-00001 R001


Page 36


The CSA Learning Centre offers a variety of courses/seminars, see www.csa.ca for furtherinformation:

Accident InvestigationA User’s Guide to Fall Protection SystemsFundamentals of Fall ProtectionOffice ErgonomicsRespiratory Protection - based on CSA Z94.4Compressed Breathing Air & SystemsFit TestingCSA/ IAPA - Safeguarding of Machinery

The Industrial Accident Prevention Association (IAPA) has a variety of offerings, seewww.iapa.on.ca.

MedicalPEL ID Type Name Duration Envir Location

3999 ARQ MEDICAL - CRANE MEDICAL (CAB CRANE) BNDCab Crane medical completed by nurse. When expiry notice is received, please contact station nurse for anappointment. This is not scheduled by the training department.

5253 ARQ MEDICAL - CRANE MEDICAL (NON CAB CRANE) BNDCrane medical completed by station nurse for Broderson and Grove Stevedore Cranes.

23783 ARQ MEDICAL - RESPIRATOR MEDICAL ASSESSMENT - SCBA 1 hour(s) BNDThis is a requirement of the respiratory protection program and must be completed before annual training or fittesting can be completed.

24643 ARQ MEDICAL - RESPIRATORY MEDICAL ASSESSMENT - NON SCBA 1 hour(s) BNDThis is a requirement of the respiratory protection program and must be completed before annual training or fittesting can be completed.

28823 ARQ MEDICAL - INITIAL BRUCE POWER FITNESS ASSESSMENT - BNDThis test is required by all individuals who are assigned to Bruce Emergency Services Team (BEST) BEST

29543 ARQ MEDICAL - HEARING TEST 2 hour(s) BNDAudiogram for people who are noise exposed.This is an administrative requirement. Medical services performsthe testing and provides the credit input.

61624 ARQ MEDICAL - REQUAL OF BRUCE POWER FITNESS ASSESSMENT - BND BEST

62721 ARQ MEDICAL - HEAT STRESS 1 hour(s) BNDUsed by Health Services to track staff who work in heat stress environmentsSee BP-SM-00043 Working InHot Environments

62722 ARQ MEDICAL - REGISTERED SILICA/ASBESTOS WORK 1 hour(s) BNDUsed by Health Services to track silica or asbestos workers - surveillanceSee BP-SM-00045 Bruce PowerAsbestos Control Program

62723 ARQ MEDICAL - REQUIRES VISION TEST 1 hour(s) BNDUsed by Medical Services to track staff who require vision testing to maintain their inspection certification

62724 ARQ MEDICAL - ENTERS CONFINED SPACE 1 hour(s) BNDUsed by Health services to track staff who enter confined spacesSee BP-SM-00023 Entry Into Confined

62725 ARQ MEDICAL - LIFT TRUCK OPERATOR 1 hour(s) BNDUsed by Health Services to track staff who require medical to operate a lift truckPer CSA Standard B335-94section 3.1

62726 ARQ MEDICAL - COMPUTER USE > 4 HOURS TOTAL/DAY OR > 2 1 hour(s) BNDHOURS/DAY CONTINUOUS

Used by Health Services to track staff who are frequent users of computer workstations See BP-SM-00015,Ergonomic Assessment Of Injured Workers In Office And Computer Workstation Environments

62727 ARQ MEDICAL - SEWAGE WORKER BNDUsed by Health Services to track workers who are or maybe exposed to sewage

62728 ARQ MEDICAL - USES FITNESS ROOMS BNDUsed by Health Services to track users of company equipped fitness rooms

62729 ARQ MEDICAL - NIGHT/SHIFT WORKER BND


TQD-00001 R001


Page 37


Used by Health Services to track staff who work shifts62730 ARQ MEDICAL - WORKS AT HEIGHTS BND

Used by Health Services to track staff who work at heights62731 ARQ MEDICAL - PLASTIC SUITS BND

Used by Health Services to track staff who wear plastics - part of the respiratory protection programSeeBP-SM-00030 Requirements For Respiratory Protection and CSA Standard 94.4-02

63001 ARQ MEDICAL - VAULT WORK 1 hour(s) BNDUsed by Medical Services to track staff who are required to work in the vault.

63002 ARQ MEDICAL - SECURITY 1 hour(s) BNDUsed by Medical Services to track Security personnel who have completed their required medical.


tqd-00001 - conventional safety - training and ... · to support requirements of ohsa and...

Documents