tooling for composites and aerospace materialsmedia.guhring.com/catalogs/eohahkc1bgy.pdf ·...
TRANSCRIPT
Tooling for Composites and Aerospace Materials• Diamond coated, carbide and PCD tools
• Routers, drills, and end mills
• Full special design capabilities
2
DIAMOND COATED DRILLS Material-specific design and sub-micron grain carbide grade to machine carbon fiber-reinforced polymer (CFRP) composite materials by minimizing delamination and increasing tool life. A special 90° point angle increases hole quality, by lowering the thrust requirements. Diamond coated for resistance to abrasion wear. Combination of point design, substrate, and coating provides longer tool life with substantially less cutting force.
Approx.Hole Dia.
d1 d1 l1 l2Order No.
mm inch mm mm
0.0980 2.489 43.00 14.00 344001454
0.1285 3.264 49.00 18.00 344001455
0.1420 3.607 52.00 20.00 344001456
#19 0.1665 4.229 58.00 24.00 344001457
#17 0.1734 4.404 58.00 24.00 344001458
#11 0.1915 4.864 62.00 26.00 344001459
0.2220 5.639 66.00 28.00 344001460
1/4* 0.2510 6.375 70.00 31.00 344001461
5/16* 0.3135 7.963 79.00 37.00 344001462
3/8* 0.3760 9.550 89.00 43.00 344001463
7/16* 0.4385 11.138 95.00 47.00 344001464
1/2* 0.5010 12.725 102.00 51.00 344001465
CFR 90 Drillsfor composites 90° point angle Solid carbide with bright finish or diamond coating
Operating Parameters:
Type Cutting speed SFM
Feed Rate - IPR
1/8 (3.17mm)
1/4 (6.35mm)
5/16 (7.94mm)
3/8 (9.52mm)
1/2 (12.7mm)
Composites (CFRP) 350 0.0020 0.0025 0.0032 0.0040 0.0050
* air cooling is recommended for optimal chip evacuation and tool life
l1
d1
l2
d1
d 2
d2 =
SPECIALIZED TOOLING for AEROSPACE APPLICATIONSCustom tools designed around special applications. We have the capacity to manufacture to customer specifications or we can utilize our highly experienced engineering staff to design tooling to meet customer requirements. Guhring not only manufactures new tools but also offers re-tip and recondition service for rejuvenating worn tools quickly and efficiently in our state-of-the-art manufacturing facilities.
4
PCD END MILLS (Inch)
Operating Parameters: Slotting*, HPC-roughing and trimming
Type Characteristic Depth of Cut ap
Width of Cut** ae
Cutting speed SFM
Feed Rate - IPT1/4 3/8 1/2 3/4 1”
Composites (CFRP) 1 x d 1 x d 800 0.0025 0.0038 0.0050 0.0068 0.0072
Graphite up to 8µm grain size 1.5 x d 1 x d 1475 0.0025 0.0038 0.0050 0.0068 0.0072
Kevlar over 50% fiber content 1 x d 1 x d 985 0.0013 0.0019 0.0025 0.0034 0.0036
* External cooling with soluble oil is recommended for optimal chip evacuation and tool life, for graphite and Kevlar-machining air cooling** at lower feed width the cutting speed vc and feed rate fz can be increased by 30%
PCD (Polycrystalline Diamond) tooling provides the ultimate in wear resistance and tool life to maximize production efficiencies. Guhring produces stocked standard PCD end mills used for machining highly abrasive composite materials. In addition, Guhring produces an extensive array of special design PCD end mills as well as reamers, drills, and counter-bores. Our engineers work directly with our customers to develop special tooling designs that decrease cycle times while dramatically increasing tool life.
d1 d2 h6 l1 l2 l3 cEDP Number
inch inch inch inch inch mm x 45°
1/4 1/4 2.50 0.79 1.07 0.05 90386700635003/8 3/8 3.00 0.79 1.24 0.05 90386700952001/2 1/2 3.00 1.03 1.33 0.05 90386701270003/4 3/4 4.00 1.03 1.62 0.05 9038670190500
d1 d2 h6 l1 l2 l3 cEDP Number
inch inch inch inch inch mm x 45°
1/2 1/2 3.00 0.57 1.33 0.05 90387001270003/4 3/4 3.00 0.57 0.98 0.05 90387001905001 1 4.00 1.03 1.62 0.05 9038700254000
Series 3867 2-flute DL100PCD tipped, straight fluteStandard length, center cutting
Series 3870 3-flute DL100PCD tipped, straight fluteStandard length, non-center cutting
l2
l1
d 1d 2
l3
c
l2
l1
d 1d 2
l3
c
5
d1 d2 h6 l1 l2 l3 rEDP Number
mm mm mm mm mm mm
4.000 6.000 51.00 6.00 6.40 0.10 90549200400005.000 6.000 51.00 8.00 8.40 0.10 90549200500006.000 6.000 57.00 8.00 21.00 0.10 90549200600008.000 8.000 63.00 8.00 27.00 0.10 90549200800008.000 8.000 63.00 12.00 27.00 0.10 905492008001010.000 10.000 72.00 8.00 32.00 0.10 905492010000010.000 10.000 72.00 16.00 32.00 0.10 905492010001012.000 12.000 83.00 8.00 38.00 0.10 905492012000012.000 12.000 83.00 16.00 38.00 0.10 905492012001014.000 14.000 83.00 8.00 38.00 0.10 905492014000014.000 14.000 83.00 16.00 38.00 0.10 905492014001016.000 16.000 100.00 12.00 52.00 0.10 905492016000016.000 16.000 100.00 20.00 52.00 0.10 905492016001018.000 18.000 100.00 12.00 52.00 0.10 905492018000018.000 18.000 100.00 20.00 52.00 0.10 905492018001020.000 20.000 100.00 12.00 50.00 0.10 905492020000020.000 20.000 100.00 20.00 50.00 0.10 9054920200010
Series 5492 2-flutePCD tipped, straight fluteRadial coolant through, standard length
Series 5493 2-flutePCD tipped, straight fluteRadial coolant through, long length
l2
l1
d 1d 2
l3
r
d1 d2 h6 l1 l2 l3 rEDP Number
mm mm mm mm mm mm
4.000 6.000 70.00 6.00 6.40 0.10 90549300400005.000 6.000 70.00 8.00 8.40 0.10 90549300500006.000 6.000 75.00 8.00 21.00 0.10 90549300600008.000 8.000 100.00 8.00 27.00 0.10 90549300800008.000 8.000 100.00 12.00 27.00 0.10 905493008001010.000 10.000 100.00 8.00 32.00 0.10 905493010000010.000 10.000 100.00 16.00 32.00 0.10 905493010001012.000 12.000 100.00 8.00 38.00 0.10 905493012000012.000 12.000 100.00 16.00 38.00 0.10 905493012001014.000 14.000 100.00 8.00 38.00 0.10 905493014000014.000 14.000 100.00 16.00 38.00 0.10 905493014001016.000 16.000 150.00 12.00 52.00 0.10 905493016000016.000 16.000 150.00 20.00 52.00 0.10 905493016001018.000 18.000 125.00 12.00 52.00 0.10 905493018000018.000 18.000 125.00 20.00 52.00 0.10 905493018001018.000 18.000 150.00 20.00 52.00 0.10 905493018002018.000 18.000 150.00 12.00 52.00 0.10 905493018003020.000 20.000 150.00 12.00 50.00 0.10 905493020000020.000 20.000 150.00 20.00 50.00 0.10 9054930200010
l2
l1
d 1d 2
l3
r
PCD END MILLS (Metric)
6
PCD END MILLS (Metric)
d1 d2 h6 l1 l2 l3 rEDP Number
mm mm mm mm mm mm
14.000 14.000 83.00 8.00 38.00 0.10 905495014000014.000 14.000 83.00 16.00 38.00 0.10 905495014001016.000 16.000 100.00 12.00 52.00 0.10 905495016000016.000 16.000 100.00 20.00 52.00 0.10 905495016001018.000 18.000 100.00 12.00 52.00 0.10 905495018000018.000 18.000 100.00 20.00 52.00 0.10 905495018001020.000 20.000 100.00 12.00 50.00 0.10 905495020000020.000 20.000 100.00 20.00 50.00 0.10 9054950200010
Series 5495 3-flutePCD tipped, straight fluteRadial coolant through, standard length
Series 5496 3-flutePCD tipped, straight fluteRadial coolant through, long length
l2
l1
d 1d 2
l3
r
d1 d2 h6 l1 l2 l3 rEDP Number
mm mm mm mm mm mm
14.000 14.000 100.00 8.00 38.00 0.10 905496014000014.000 14.000 100.00 16.00 38.00 0.10 905496014001016.000 16.000 150.00 12.00 52.00 0.10 905496016000016.000 16.000 150.00 20.00 52.00 0.10 905496016001018.000 18.000 150.00 12.00 52.00 0.10 905496018000018.000 18.000 150.00 20.00 52.00 0.10 905496018001020.000 20.000 150.00 12.00 50.00 0.10 905496020000020.000 20.000 150.00 20.00 50.00 0.10 9054960200010
l2
l1
d 1d 2
l3
r
Operating Parameters: Width of Cut = 1 x d; slotting*, HPC-roughing and trimming
Type Characteristic Depth of Cut ap
Cutting speed SFM
Feed Rate - IPT4mm 6mm 8mm 10mm 12mm 16mm 20mm
Composites (CFRP) 1 x d 985 0.0016 0.0024 0.0031 0.0039 0.0047 0.0059 0.0071
Graphite up to 8µm grain size 1.5 x d 1475 0.0016 0.0024 0.0031 0.0039 0.0047 0.0059 0.0071
Kevlar over 50% fiber content 1 x d 985 0.0006 0.0012 0.0016 0.0020 0.0024 0.0031 0.0035
* int. cooling with soluble oil is recommended for optimal chip evacuation and tool life, for graphite and Kevlar-machining air cooling** at lower feed width the cutting speed vc and feed rate fz can be increased by 30%
7
Carbide Routers (Inch)
d1 e10 d2 h6 l1 l2 l3 no.Order Number
inch inch inch inch inch flutes
1/4 1/4 2-1/2 3/4 1.08 10 3022840153/8 3/8 3 1 1.43 14 3022840161/2 1/2 3-1/2 1-1/4 1.73 15 3022840175/8 5/8 4 1-5/8 2.24 15 302284018
d1 e10 d2 h6 l1 l2 l3 c no.Order Number
inch inch inch inch inch mm x 45° flutes
1/4 1/4 2-1/2 3/4 1.32 0.15 10 3022840003/8 3/8 3 1 1.58 0.15 14 3022840011/2 1/2 3-1/2 1-1/4 1.93 0.15 15 3022840025/8 5/8 4 1-5/8 2.43 0.15 15 302284003
Inch sizes CR 100 plungingMulti-flute plunging routerSolid carbide, Cristall coated
Inch sizes CR 100 square endMulti-flute slotting routerSolid carbide, Cristall coated
l2
l1
d1d2
l3
c
Operating Parameters: Slotting*, HPC-roughing and trimming
Type Characteristic Depth of Cut ap
Width of Cut** ae
Cutting speed SFM
Feed Rate - IPT1/4 3/8 1/2 5/8
Composites (CFRP) 1 x d 1 x d 500 0.0003 0.0003 0.0004 0.0004
Kevlar over 50% fiber content 1 x d 1 x d 460 0.0013 0.0019 0.0025 0.0031
* Air cooling is recommended for optimal chip evacuation and tool life.** at lower feed width the cutting speed vc and feed rate fz can be increased by 20%
Slotting Router Features:• For slot and periphery milling in composite materials• Capable of roughing and finishing in one pass• Extremely rigid design minimizes deflection and vibration• Flute geometry promotes shearing action, minimizes
delamination and burrs• Multiple flutes for maximum material removal, non-center cutting• 0.006” chamfer for micro-edge protection and extended tool life
Plunging Carbide Router Features:• 118° drill point allows for plunging operations, can also be used
for slotting and periphery milling• Multiple flutes for maximum material removal• Extremely rigid design minimizes deflection and vibration• Flute geometry promotes shearing action, minimizes• delamination and burrs
d2
l1
d1
l2l3
8
Carbide Routers (Metric)
d1 e10 d2 h6 l1 l2 l3 no.EDP Number
mm mm mm mm mm flutes
4.000 4.000 55.00 12.00 27.00 6 90672000400006.000 6.000 65.00 18.00 29.00 8 90672000600008.000 8.000 75.00 24.00 39.00 10 906720008000010.000 10.000 80.00 30.00 40.00 12 906720010000012.000 12.000 93.00 36.00 48.00 14 906720012000016.000 16.000 108.00 48.00 60.00 14 9067200160000
Series 6720 CR 100 plungingMulti-flute plunging routerSolid carbide, Cristall coated
Series 6717 CR 100 square endMulti-flute slotting routerSolid carbide, Cristall coated
d1 e10 d2 h6 l1 l2 l3 c no.EDP Number
mm mm mm mm mm mm x 45° flutes
4.000 6.000 57.00 10.00 19.40 0.10 6 90671700400006.000 6.000 65.00 15.00 29.00 0.15 8 90671700600008.000 8.000 75.00 20.00 39.00 0.15 10 9067170080000
10.000 10.000 80.00 25.00 40.00 0.15 12 906717010000012.000 12.000 93.00 32.00 48.00 0.15 14 906717012000016.000 16.000 108.00 34.00 60.00 0.15 14 9067170160000
l2
l1
d1d2
l3
c
Slotting Router Features:• For slot and periphery milling in composite materials• Capable of roughing and finishing in one pass• Extremely rigid design minimizes deflection and vibration• Flute geometry promotes shearing action, minimizes
delamination and burrs• Multiple flutes for maximum material removal, non-center cutting• 0.006” chamfer for micro-edge protection and extended tool life
Plunging Carbide Router Features:• 118° drill point allows for plunging operations, can also be used
for slotting and periphery milling• Multiple flutes for maximum material removal• Extremely rigid design minimizes deflection and vibration• Flute geometry promotes shearing action, minimizes• delamination and burrs
Operating Parameters: Width of Cut = 1 x d; slotting*, HPC-roughing and trimming
Type Characteristic Depth of Cut ap
Cutting speed SFM
Feed Rate - IPT4mm 6mm 8mm 10mm 12mm 16mm
Composites (CFRP) 1 x d 500 0.0003 0.0003 0.0003 0.0003 0.0004 0.0004
Kevlar over 50% fiber content 1 x d 460 0.0012 0.0020 0.0020 0.0020 0.0020 0.0020
* Air cooling is recommended for optimal chip evacuation and tool life.** at lower feed width the cutting speed vc and feed rate fz can be increased by 20%
d2
l1
d1
l2l3
9
Series 6719 CR 100Multi-flute plunging routerSolid carbide, Cristall coated
Series 6718 CR 100 AirMulti-flute slotting routerSolid carbide, Cristall coated
d1 e10 d2 h6 l1 l2 l3 noEDP Number
mm mm mm mm mm flutes
4.000 6.000 57.00 10.00 19.40 6 90671900400006.000 6.000 65.00 15.00 29.00 8 90671900600008.000 8.000 75.00 20.00 39.00 10 906719008000010.000 10.000 80.00 25.00 40.00 12 906719010000012.000 12.000 93.00 32.00 48.00 14 906719012000016.000 16.000 108.00 34.00 60.00 14 9067190160000
d1 e10 d2 h6 l1 l2 l3 c noEDP Number
mm mm mm mm mm mm x 45° flutes
6.000 6.000 70.00 24.00 34.00 0.15 8 90671800600008.000 8.000 80.00 32.00 44.00 0.15 10 906718008000010.000 10.000 90.00 40.00 50.00 0.15 12 906718010000012.000 12.000 110.00 48.00 65.00 0.15 14 906718012000016.000 16.000 130.00 64.00 82.00 0.15 14 9067180160000
l2
l1
d1
d2
l3
c
l2
l1
d1
d2
l3
c
Carbide Routers (Metric)
Operating Parameters: Width of Cut = 1 x d; slotting*, HPC-roughing and trimming
Type Characteristic Depth of Cut ap
Cutting speed SFM
Feed Rate - IPT4mm 6mm 8mm 10mm 12mm 16mm
Composites (CFRP) 1 x d 500 0.0003 0.0003 0.0003 0.0003 0.0004 0.0004
Kevlar over 50% fiber content 1 x d 460 0.0012 0.0020 0.0020 0.0020 0.0020 0.0020
* Air cooling is recommended for optimal chip evacuation and tool life.** at lower feed width the cutting speed vc and feed rate fz can be increased by 20%
These diamond coated carbide composite routers are the tools of choice for many industrial hand routing applications, such as fiberglass or wood composites in the boat industry. Solid carbide composite routing is frequently done with air. The applications of routers include cut-out composite routing with templates, trimming operations done by following fixtures, and free-hand trimming. Diamond coated carbide router bits are able to perform many different tasks that standard end mills and drills cannot.
10
AeroX HSCO8 SPLIT POINT DRILLSThese drills are made from M42 HSCO (8% cobalt) and have a bronze oxide finish - they’re designed for optimal performance at high temperatures. The 135° split point is ground to NAS 907 P3 specifications for spot-on accuracy and minimized axial feed forces.
Range of application:• Reduced core diameter lends itself well to hand drilling applications in difficult-to-machine materials or at high temperatures (i.e., in the aviation industry, repair of titanium or titanium/aluminum aviation components)• Capable of drilling in high-alloyed steel, cast and non-ferrous materials• Can be used in CNC machines
l1
d 1
l2
d1 d1 l1 l2EDP No.
mm inch mm mm1.00 34.00 12.00 90101800100001.10 36.00 14.00 90101800110001.20 38.00 16.00 90101800120001.30 38.00 16.00 90101800130001.40 40.00 18.00 90101800140001.50 40.00 18.00 90101800150001.59 1/16 43.00 20.00 90101800159001.60 43.00 20.00 90101800160001.70 43.00 20.00 90101800170001.80 46.00 22.00 90101800180001.90 46.00 22.00 90101800190001.98 5/64 49.00 24.00 90101800198002.00 49.00 24.00 90101800200002.10 49.00 24.00 90101800210002.20 53.00 27.00 90101800220002.30 53.00 27.00 90101800230002.38 3/32 57.00 30.00 90101800238002.40 57.00 30.00 90101800240002.50 57.00 30.00 90101800250002.60 57.00 30.00 90101800260002.70 61.00 33.00 90101800270002.78 7/64 61.00 33.00 90101800278002.80 61.00 33.00 90101800280002.90 61.00 33.00 90101800290003.00 61.00 33.00 90101800300003.10 65.00 36.00 90101800310003.17 1/8 65.00 36.00 90101800317003.20 65.00 36.00 90101800320003.25 65.00 36.00 90101800325003.30 65.00 36.00 90101800330003.40 70.00 39.00 90101800340003.50 70.00 39.00 90101800350003.57 9/64 70.00 39.00 90101800357003.60 70.00 39.00 90101800360003.70 70.00 39.00 90101800370003.80 75.00 43.00 90101800380003.90 75.00 43.00 90101800390003.97 5/32 75.00 43.00 90101800397004.00 75.00 43.00 9010180040000
d1 d1 l1 l2EDP No.
mm inch mm mm4.10 75.00 43.00 90101800410004.20 75.00 43.00 90101800420004.30 80.00 47.00 90101800430004.40 80.00 47.00 90101800440004.50 80.00 47.00 90101800450004.60 80.00 47.00 90101800460004.70 80.00 47.00 90101800470004.76 3/16 86.00 52.00 90101800476004.80 86.00 52.00 90101800480004.90 86.00 52.00 90101800490005.00 86.00 52.00 90101800500005.10 86.00 52.00 90101800510005.16 13/64 86.00 52.00 90101800516005.20 86.00 52.00 90101800520005.30 86.00 52.00 90101800530005.40 93.00 57.00 90101800540005.50 93.00 57.00 90101800550005.56 7/32 93.00 57.00 90101800556005.60 93.00 57.00 90101800560005.70 93.00 57.00 90101800570005.80 93.00 57.00 90101800580005.90 93.00 57.00 90101800590005.95 15/64 93.00 57.00 90101800595006.00 93.00 57.00 90101800600006.10 101.00 63.00 90101800610006.20 101.00 63.00 90101800620006.30 101.00 63.00 90101800630006.35 1/4 101.00 63.00 90101800635006.40 101.00 63.00 90101800640006.50 101.00 63.00 90101800650006.60 101.00 63.00 90101800660006.70 101.00 63.00 90101800670006.80 109.00 69.00 90101800680006.90 109.00 69.00 90101800690007.00 109.00 69.00 90101800700007.10 109.00 69.00 90101800710007.14 9/32 109.00 69.00 90101800714007.20 109.00 69.00 90101800720007.30 109.00 69.00 9010180073000
Series 1018AeroX M42 HSCO (8% cobalt) Web thinning ≥ Ø 1.000 AeroX drills are stocked in Germany
11
d1 d1 l1 l2EDP No.
mm inch mm mm7.40 109.00 69.00 90101800740007.50 109.00 69.00 90101800750007.54 19/64 117.00 75.00 90101800754007.60 117.00 75.00 90101800760007.70 117.00 75.00 90101800770007.80 117.00 75.00 90101800780007.90 117.00 75.00 90101800790007.94 5/16 117.00 75.00 90101800794008.00 117.00 75.00 90101800800008.10 117.00 75.00 90101800810008.20 117.00 75.00 90101800820008.30 117.00 75.00 90101800830008.33 21/64 117.00 75.00 90101800833008.40 117.00 75.00 90101800840008.50 117.00 75.00 90101800850008.60 125.00 81.00 90101800860008.70 125.00 81.00 90101800870008.73 11/32 125.00 81.00 90101800873008.80 125.00 81.00 90101800880008.90 125.00 81.00 90101800890009.00 125.00 81.00 90101800900009.10 125.00 81.00 90101800910009.13 23/64 125.00 81.00 90101800913009.20 125.00 81.00 90101800920009.30 125.00 81.00 90101800930009.50 125.00 81.00 9010180095000
d1 d1 l1 l2EDP No.
mm inch mm mm9.52 3/8 133.00 87.00 90101800952009.60 133.00 87.00 90101800960009.70 133.00 87.00 90101800970009.80 133.00 87.00 90101800980009.90 133.00 87.00 90101800990009.92 25/64 133.00 87.00 901018009920010.00 133.00 87.00 901018010000010.10 133.00 87.00 901018010100010.20 133.00 87.00 901018010200010.30 133.00 87.00 901018010300010.32 13/32 133.00 87.00 901018010320010.50 133.00 87.00 901018010500010.72 27/64 142.00 94.00 901018010720010.80 142.00 94.00 901018010800011.00 142.00 94.00 901018011000011.11 7/16 142.00 94.00 901018011110011.50 142.00 94.00 901018011500011.51 29/64 142.00 94.00 901018011510011.91 15/32 151.00 101.00 901018011910012.00 151.00 101.00 901018012000012.20 151.00 101.00 901018012200012.30 31/64 151.00 101.00 901018012300012.50 151.00 101.00 901018012500012.70 1/2 151.00 101.00 901018012700012.80 151.00 101.00 901018012800013.00 151.00 101.00 9010180130000
Material groupHardness
SFMFeed Rate - IPR
HRC BHN 1/64 in. .5 mm
1/16 in. 1.59 mm
1/8 in. 3.17 mm
1/4 in. 6.35 mm
3/8 in. 9.52 mm
1/2 in. 12.70 mm
5/8 in. 15.87 mm
3/4 in. 19.05 mm
1 in. 25.4 mm
Common structural steels - ≤ 150 115 0.0005 0.0007 0.0039 0.0063 0.0098 0.0098 0.0124≤32 ≤ 301 100 0.0004 0.0006 0.0031 0.0049 0.0079 0.0079 0.0098
Free-cutting steels≤25 ≤ 255 130 0.0005 0.0007 0.0039 0.0063 0.0098 0.0098 0.0124≤32 ≤ 301 130 0.0004 0.0006 0.0031 0.0049 0.0079 0.0079 0.0098
Unalloyed heat-treatable steels≤20 ≤ 220 130 0.0004 0.0006 0.0031 0.0049 0.0079 0.0079 0.0098≤25 ≤ 255 130 0.0004 0.0006 0.0031 0.0049 0.0079 0.0079 0.0098≤32 ≤ 301 115 0.0003 0.0006 0.0025 0.0039 0.0063 0.0063 0.0079
Alloyed heat-treatable steels≤32 ≤ 301 65 0.0003 0.0006 0.0025 0.0039 0.0063 0.0063 0.0079≤43 ≤ 402 50 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063
Unalloyed case hardened steels ≤25 ≤ 255 120 0.0005 0.0007 0.0039 0.0063 0.0098 0.0098 0.0124
Alloyed case hardened steels≤32 ≤ 301 65 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063≤43 ≤ 402 50 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063
Nitriding steels≤32 ≤ 301 50 0.0003 0.0006 0.0025 0.0039 0.0063 0.0063 0.0079≤43 ≤ 402 40 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063
Tool steels≤25 ≤ 255 50 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063≤43 ≤ 402 40 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063
High speed steels ≤43 ≤ 402 50 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063Spring steels ≤38 ≤ 354 25 0.0002 0.0003 0.0016 0.0025 0.0039 0.0039 0.0049
Stainless steelssulphured ≤28 ≤ 273 60 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063austenitic ≤36 ≤ 337 45 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063martensitic ≤46 ≤ 435 50 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063
Hardened steels≤48 ≤ 460 15 0.0002 0.0002 0.0013 0.0020 0.0031 0.0031 0.0039≤66 -
Special alloys ≤54 ≤ 549 25 0.0002 0.0002 0.0013 0.0020 0.0031 0.0031 0.0039
Cast iron≤23 ≤ 242 115 0.0005 0.0007 0.0039 0.0063 0.0098 0.0098 0.0124≤38 ≤ 354 100 0.0005 0.0007 0.0039 0.0063 0.0098 0.0098 0.0124
Speroidal graphite iron and malleable cast iron
≤23 ≤ 242 100 0.0005 0.0007 0.0039 0.0063 0.0098 0.0098 0.0124≤38 ≤ 354 90 0.0005 0.0007 0.0039 0.0063 0.0098 0.0098 0.0124
Chilled cast iron ≤38 ≤ 354 35 0.0003 0.0005 0.0020 0.0031 0.0049 0.0049 0.0063
Ti and Ti-alloys≤25 ≤ 255 35 0.0002 0.0003 0.0016 0.0025 0.0039 0.0039 0.0049≤43 ≤ 402 20 0.0002 0.0003 0.0016 0.0025 0.0039 0.0039 0.0049
Aluminum and Al-alloys - ≤ 120 295 0.0006 0.0008 0.0049 0.0079 0.0124 0.0124 0.0157Al wrought alloys - ≤ 200 295 0.0006 0.0008 0.0049 0.0079 0.0124 0.0124 0.0157
Al cast alloys ≤ 10% Si - ≤ 180 260 0.0006 0.0008 0.0049 0.0079 0.0124 0.0124 0.0157≤ 24% Si - ≤ 180 230 0.0005 0.0007 0.0039 0.0063 0.0098 0.0098 0.0124
Magnesium alloys - ≤ 120 230 0.0005 0.0007 0.0039 0.0063 0.0098 0.0098 0.0124Copper low-alloyed - ≤ 150 230 0.0004 0.0006 0.0031 0.0049 0.0079 0.0079 0.0098
Brass short-chipping - ≤ 180 195 0.0004 0.0006 0.0031 0.0049 0.0079 0.0079 0.0098long-chipping - ≤ 180 130 0.0004 0.0006 0.0031 0.0049 0.0079 0.0079 0.0098
Bronze short-chipping - ≤ 180 115 0.0003 0.0006 0.0025 0.0039 0.0063 0.0063 0.0079≤25 ≤ 255 110 0.0003 0.0006 0.0025 0.0039 0.0063 0.0063 0.0079
Bronze long-chipping ≤25 ≤ 255 65 0.0003 0.0006 0.0025 0.0039 0.0063 0.0063 0.0079≤32 ≤ 301 50 0.0003 0.0006 0.0025 0.0039 0.0063 0.0063 0.0079
Duroplastics - - 65 0.0003 0.0006 0.0025 0.0039 0.0063 0.0063 0.0079Thermoplastics - - 100 0.0004 0.0006 0.0031 0.0049 0.0079 0.0079 0.0098New cast materials GGV ≤20 ≤ 220New cast materials ADI ≤32 ≤ 301Kevlar - -Glass, carbon concentrated plastics - -
Item # 400001042
Guhring, Inc. Main OfficeP.O. Box 643, Brookfield, WI 53008-0643
Shipping Address1445 Commerce AvenueBrookfield, WI 53045Tel (262) 784-6730 (800) 776-6170Fax (262) 784-9096
West Coast Distribution Center and Reconditioning Facility15581 Computer Ln Huntington Beach, CA 92649
Reconditioning Facility121 W Dudley Town Rd.Bloomfield, CT 06002
Manufacturing and Reconditioning Facility29550 W.K. Smith Rd. Suite BNew Hudson, MI 48165
Guhring Corporation20 Steckle Place, Unit #14Kitchener, ON N2E 2C3Tel (519) 748-9664 (800) 463-5555Fax (519) 748-2954
SPECIAL TOOLINGSOLUTIONS
MODULAR TOOLING SYSTEMS
COUNTERSINKING/DE-BURRING
DRILLING MILLING
TOOL RECONDITIONING SERVICE
REAMING PCD/PCBNTAPPING/THREADMILLING/FLUTELESS TAPPING