tm owner's/service manual for series 03 and later fully

Read manualbefore operation.Failure to do somay result inserious bodilyinjury and/orproperty damage.Keep manual inEntervan.

WARNING

Owner'sManual

ENTERENTERTM

19

96

an

d n

ew

er C

hry

sler E

nte

rvan

II1

99

6 a

nd n

ew

er C

hry

sler E

nte

rvan

II® ®

Bra

un

Serie

s 03

an

d la

ter

Bra

un

Serie

s 03

an

d la

ter

Note to Dealer:Provide this manual

to the consumer

See inside cover forwarranty/registration

information

"Providing Access to the World"International Corporate Hdqrs: P.O. Box 310 Winamac, IN 46996 USA

1-800-THE LIFT (219) 946-6153 FAX: (219) 946-4670

®

5230096-03September 1996

August 1998Revision

Braun Series 03 and later 1996 and newer Chrysler Entervan IIBraun Series 03 and later 1996 and newer Chrysler Entervan II®®

Owner's/Service Manual forSeries 03 and laterFully-Automatic1996 and newer Chrysler

Entervan® II

ENTERTM

Congratulations

We at The Braun Corporation wish to express our fullest appreciationon your new purchase.

With you in mind, our skilled craftsmen have designed andassembled the finest lowered floor vehicle available.

This manual includes operating instructions, servicing instructions,and instructions for troubleshooting, if needed.

Your Entervan® II is built for dependability, and will bring you years ofpleasure and independence, as long as the maintenance is performed regularlyand the Entervan® is operated by an instructed person.

THE BRAUN CORPORATION

Ralph W. BraunChief Executive Officer

Immediately upon receiving:

Warranty/Registration Instructions

Examine your Entervan® for any damage. Notifythe carrier at once with any claims.

Two warranty/registration cards (shown right)are supplied with each Entervan®. One islabeled “Dealer” and the other is labeled“Owner." The dealer must process the cardlabeled “Dealer." The consumer must fill out thecard labeled “Owner” and mail it to The BraunCorporation. Warranty details are provided inthe Warranty section within this manual.

•

•

The Braun Serial No./Series No. identification decal (shown below) is located on the Entervan® driver'sdoor jamb. This I.D. tag contains the product identification information provided on the Warranty/Registration card. Record the information in the space provided below. This information must beprovided when filing a warranty claim or ordering parts. See the Return Authorization sectionfor further details.

RETAIN THIS INFORMATION FOR FUTURE USE. HAVE THIS INFORMATION WHEN FILING AWARRANTY CLAIM OR ORDERING PARTS!

•

Sincerely,

1014 S. MONTICELLO P.O. BOX 310 WINAMAC, IN. 46996 219•946•6153

VIN # 1B4GP54R4TB154992ENTERVAN # 5200096-03 SERIAL 1203ENG. SERIES 03 ENG. RAMP SERIES 02MFG 07/20/96 DOOR OP. SERIES 02PAINT CODE INT - DIU35799KNEELING 1 EXT - DBU5069

Sample: Identification Decal

Entervan® Model No.

Engineering Series No.

Serial No.

Ramp Series No.

Door Operator Series No.

Date of Manufacture

•

Sample: Warranty/Registration Card

EntervanModel No. Kneeling

Door OperatorSeries No.Serial No.

RampSeries No.

EngineeringSeries No.

5200096 - 03 - 1203 - 02 - 02 - 1

Contents

Section 1: Operation

Entervan II Features and Options ....................... 2, 3

Safety Precautions ................................................ 4-6

Pre-Operation Notes and Details

Control Switches ............................................. 7-10

Dash-Mounted Kneel andOpen/Close Switches .................................... 8

Rear Wall-Mounted Manual/Auto andOpen/Close Switches .................................... 8

Mini Remote Control Transmitter .................. 9

Full Size Remote Control Transmitter ........... 9

Passenger Door Outside Key Entry ............ 10

Kneel Actuator Manual/Auto Switch ............ 10

Kneeling Feature .......................................... 11, 12

Automatic Power Door ........................................12

Automatic Power Ramp ................................13, 14

Driver Side Slide Door ........................................14

Ramp Safety .......................................................15

Wheelchair-Equipped Occupant Seat Belts ........15

Stabilizing Wheelchairs ................................ 15, 16

Wheelchair Orientation and SecurementDuring Transport ................................................ 16

Operation Procedure Review ............................. 16

Preventative Maintenance ..................................17

Door Locks and Anti-Theft (Alarm) System ........17

Power Operating Instructions ................................18

Passive Access (Non-Wheelchair) Instructions ...19

Ramp Removal Instructions ............................ 20, 21

Manual Operation

Door and Ramp ManualOperating Instructions .................................. 21, 22

Kneel Actuator Manual ReleaseInstructions .................................................. 23, 24

Wheelchair and Occupant Restraint ................ 25-29

Chrysler Easy-Out Roller™ Rear Bench Seat ........ 29

Quick-Release Front Seats .............................. 30, 31

Spare Tire Mount and Storage Cabinet .................32

Tire Changing .................................................... 32, 33

Section 2: Maintenance

Maintenance and Lubrication Schedule .......... 34-36

Section 3: Troubleshooting

Troubleshooting Diagnosis Chart .................... 37-42

Auxiliary Power Supply for Dealer-InstalledPower Seat or Tie-Down ......................................... 44

Wiring Diagram (Fold Out) ........................... 45A, 46A

Electrical Schematic (Fold Out) .................. 45B, 46B

Section 4: Repair Parts

Power Door Operator Assembly ............................47

Power Ramp Motor Assembly ............................... 48

Ramp Assembly ...................................................... 49

Kneel Actuator Assembly ...................................... 50

Kneel Actuator Manual ReleaseLever Assembly ...................................................... 51

Passenger Door Outside Key Entry Assembly .... 51

Decals ................................................................. 52-57

Section 5: Specifications and Dimensions

Specifications ......................................................... 58

Dimensions ............................................................. 59

Section 6: Warranty

Warranty ............................................................ 60, 61

Return Authorization Procedure ........................... 61

Tro

ub

lesho

otin

gR

epair P

artsS

pecificatio

ns &

Dim

ensio

ns

Warran

tyO

peratio

nM

ainten

ance

Entervan II Features and Options

Normal (Non-Kneeled) Position Kneeled (Lowered) Position

Power Slide Door Power RampStandard Features:

The Braun Series 03 1996 and newer Chrysler Entervan IIconversion offers the following standard features inaddition to the Chrysler Mini-Van chassis equipment.

Electromechanical Power Kneeling Rear Suspen-sion with On/Off and Override Features: “Kneeling” isthe lowering and raising motion of the Entervan electro-mechanical rear suspension (shown above). The kneelfeature reduces the slope of the ramp when deployed. AKneel On/Off Switch, an Out-of-Park Override and aMechanical Override are incorporated in the electrome-chanical power kneeling system. See pages 11 and 12for further details.

Power Slide Door with Manual Release Feature:The power door and lowered floor configuration provides52-3/4" clear vertical passageway. See page 12 fordetails.

Removable Power Ramp with Manual ReleaseFeature and Passive Access Feature: See pages 13and 14 for further details.

Passive (Non-Wheelchair) Access: This featureallows passive (non-wheelchair) access to the passengerside slide door opening when desired. See page 19 forfurther details.

Lowered Floor from Rear Axle to Firewall: Thisfeature provides additional headroom (57-1/2" floor-to-ceiling at center of van), and further reduces the slope ofthe power ramp when deployed. See Position C in theillustration and photos on the opposite page.

Lowered Driver-Side Second Sliding Door: TheBraun Corporation Entervan II conversion is available forChrysler Mini-Van chassis equipped with the driver-sidesecond sliding door option only.

Quick-Release Driver Seat: For the wheelchairoccupant who chooses to drive the Entervan II, this seat(Position A) can be removed and adaptive driving

systems custom tailored for the individual can be pur-chased from and installed by your local dealer. 56" floor-to-ceiling headroom is provided at this seating position.See pages 30 and 31 for seat removal and installationinstructions.

Quick-Release Front Passenger Seat with FloorTrack for Wheelchair and Occupant Securement: Thisseat (Position B) can be removed and the seat locationcan be utililized by a wheelchair occupant. 56" floor-to-ceiling headroom is provided at this seating position.

Floor Track for Wheelchair and Occupant Secure-ment in Mid-Point Lowered Floor Area: Floor trackprovided in the mid-point lowered floor area (Position C)can be utililized for restraint of wheelchair passenger(s).Wheelchair capacity at mid-point may have limitationsbased on the physical dimensions of specific wheelchairs.See pages 25-29 for details and instructions for wheel-chair and occupant restraint.

Forward-Facing Wheelchair and Occupant Belt/Track System: One Forward-Facing Wheelchair andOccupant Belt Kit is supplied for the restraint of onewheelchair and occupant only. Additional belt kits can bepurchased. The belt kit is used in conjunction with thefloor track. See pages 25-29 for details and instructionsfor wheelchair and occupant restraint.

Easy-Out Roller™ 3-Passenger Bench Seat at Rearof Vehicle: See page 29 for further details.

Auxiliary Power Supply for Dealer-Installed PowerSeat or Electric Tie-Downs: See page 44 for details.

Interior Spare Tire Mount/Storage Cabinet: Seepages 32 and 33 for details.

Color-Coded Control Switches: Color-coded andfunction-labeled control switches that correspond to thecolor coding and switch function labels which appear onthe Power Operation Instructions decal are provided

Op

eration

Entervan II Features and Options

BA

Horizontal “A” Track

Wheelchair Seating Positions: Wheelchairpassengers shown depict the availablewheelchair seating positions. Wheelchaircapacity at mid-point (Position C) may havelimitations based on the physical dimensionsof specific wheelchairs.

Horizontal “A” Track

Mid-Point

C

Rear Wall-MountedControl Switches

Easy-Out® 3-PassengerBench Seat

Mid-Point

C

Dash-Mounted Control Switches

Power Ramp Operator Horizontal “A” Track

BA

Horizontal“A” Track


Wheelchair Positions

inside the Entervan (dash and rear wall locations).See pages 7-10 for details.

Remote Control: Two mini remote controltransmitters are supplied for automatic operationof kneeling, door and ramp functions. See page 9for details.

Passenger Door Outside Key Entry System:An outside key entry incorporated in the frontpassenger side door lock activates the automaticoperation of kneeling, door and ramp functions aswell as operating the passenger door lock. Seepage 10 for details.

C

Options:

• Extra Wheelchair and Occupant Securement System• Full Size Remote Control Transmitter• Extra Mini Remote Control Transmitter• Remote Start

Op

eration

A

This symbol indicatesimportant informationregarding how toavoid a hazardoussituation that couldresult in minor per-sonal injury or prop-erty damage.

C CAUTIONments (if included) is providedfor your safety. Familiarity withproper operation instructionsas well as proper maintenanceprocedures are necessary toensure safe, troublefreeoperation. Safety precautionsare provided to identify poten-tially hazardous situations andprovide instruction on how toavoid them.

All information containedin this manual and supple-

Safety Precautions

SAFETY FIRST! Know That....

Note: Additional information provided to help clarify or detail a specific subject.

These symbols will appear throughout this manual as well as on the labels posted on your Entervan.Recognize the seriousness of this information.

D

If the operatinginstructions, manualoperating instructionsand/or safety precau-tions are not fullyunderstood, contactThe Braun Corpora-tion immediately.Failure to do so mayresult in seriousbodily injury and/orproperty damage.

Read this manual, supplement(s) and the Chrysler-suppliedvehicle owner's manual before operation. Read and becomefamiliar with all safety precautions, pre-operation notes anddetails, operating instructions and manual operating instruc-tions before operation. Note: Wheelchair passengers,wheelchair attendants, Entervan drivers and Entervanoperators must read and become familiar with the contentsof this manual and supplement(s) before operation.

Load and unload on level surface only.

Engage vehicle parking brake before operation.

Provide adequate clearance outside the vehicle to accom-modate the ramp.

Safety Symbols

Safety Precautions

WARNINGWARNING

B

This symbol indicatesimportant safety infor-mation regarding apotentially hazardoussituation that couldresult in seriousbodily injury and/orproperty damage.

WARNING

Do not operate Entervan if you suspect damage, wear or any abnormal condition.

Keep clear of area in which the door and ramp operate.

Close driver-side slide door before loading and unloading wheelchair passengers.

Wheelchair passengers must position and secure (buckle, engage, fasten, etc.) thewheelchair-equipped occupant seat belt before loading onto the wheelchair ramp.

Be aware of the Entervan ramp slope (angle).

WARNING

WARNING

WARNING

WARNINGO

peratio

n

WARNING

WARNING

WARNING

WARNING

Safety Precautions

Do not board an Entervan ramp if you or your attendant are intoxicated.

The wheelchair must be positioned in the center of the ramp when loading and unloading.

Load and unload clear of vehicular traffic.

Keep clear of area in which the vehicle kneels (lowers).

Do not activate control switches when anyone is near the area in which door operates,ramp operates or vehicle kneels.

Do not disengage vehicle transmission from Park “P” when a wheelchair passenger is onthe ramp.

Do not press KNEEL switch to NO position when a wheelchair passenger is on the ramp.

Do not overload or abuse the ramp. The design load capacity is 600 pounds.

Do not grip detachable wheelchair parts when assisting to stabilize wheelchair.

Do not drive Entervan with the rear of the vehicle in the kneeled (lowered) position.

Keep this manual and the Chrysler-supplied vehicle manual in the Entervan at all times.

Replace missing, worn or illegible decals.

Do not remove any guards or covers.

Do not use accessory devices* not authorized by The Braun Corporation.

Do not use an Entervan for towing. Towing with an Entervan is prohibited.

Do not install a raised top kit on an Entervan.

Never modify (alter) a Braun Corporation Entervan.

Manual Operation

Clear ramp path before performing manual unfold procedures. Ramp will free-fall.

Be certain door is fully open when manually unfolding and folding the ramp during manualoperating procedures.

Keep clear of moving parts when manually operating door and/or ramp.

Remote Control

Be aware of the location and condition of the remote control transmitter at all times.Accidental activation of switches may cause unintended operation.

Do not operate remote control unit with anyone on the ramp or near the area in which dooroperates, ramp operates or vehicle kneels.

Discontinue remote control use immediately if any unexplained and/or improper operationoccurs. Contact your dealer or call The Braun Corporation at 1-800-THE LIFT.

Do not interface after-market control systems* with a Braun Entervan.

WARNING

* See page 6 for The Braun Corporation After-Market Control Systems Policy.

noi

tare

pO

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

Safety Precautions

Wheelchair and Occupant Restraint

No product developed to date can guarantee successfulsecurement of the wheelchair, even at low speeds, in theevent of an accident. The Braun Wheelchair and OccupantBelt/Track System does meet the most widely referencedFederal Motor Vehicle Safety Standards used for contempo-rary restraint equipment. However, this equipment does notensure stability of the wheelchair in the event of an accidentat any speed.

The Wheelchair and Occupant Belt/Track System suppliedwith this unit must be utilized as specified within this manual.

Read and become familiar with all Forward-Facing Wheel-chair and Occupant Belt/Track System Instructions asspecified in this manual prior to installation or operationprocedures. If the instructions are not fully understood,contact The Braun Corporation immediately.

WARNINGIf the operatinginstructions, manualoperating instructionsand/or safety precau-tions are not fullyunderstood, contactThe Braun Corpora-tion immediately.Failure to do so mayresult in seriousbodily injury and/orproperty damage.

WARNING

WARNING

WARNING

When using wheelchair restraints not supplied with the Entervan, read and become familiarwith all installation and operation instructions supplied with your particular wheelchairrestraint system prior to installation or operation procedures. If the instructions are not fullyunderstood, contact the manufacturer immediately.

Non-Wheelchair Passenger Restraint

Observe all local, state and federal laws for specific seat belt usage requirements.

Refer to Chrysler-supplied owner's manual for instructions regarding passenger (childrenand adults) restraints.

Quick-Release Front Seats

Quick-release front seat securement devices must be fully engaged before occupyingseats or operating vehicle.

WARNING

WARNING

WARNING

WARNING

WARNING

Chrysler Easy-Out Roller™ Seats

Install, remove and operate ChryslerEasy-Out Roller™ seats as detailed inChrysler owner's manual.

Tire Changing and Jacking

Follow all jacking and tire changinginstructions and safety precautions in theChrysler-supplied owner's manual whenchanging a flat tire or raising the vehicle.

All Precautions

Failure to follow these safety precautionsmay result in serious bodily injury and/orproperty damage.

WARNING

WARNING

The Braun Corporation manufacturesdedicated control systems for it's products(i.e., wheelchair lifts, door operators, rampsystems, kneeling systems). These controlsystems have been designed and tested foruse in conjunction with specific Braunproducts. Braun control systems are theonly control systems authorized for use withBraun products. Do not attempt to interfaceafter-market control systems with Braunproducts. To do so may result in seriousbodily injury and/or property damage.For information about the proper controlsystem for a specific Braun product, contactThe Braun Corporation at 1-800-THE LIFT.

Braun Corporation After-MarketControl Systems Policy

Op

eration


The Entervan II provides fullyautomatic operation of theelectromechanical “kneeling”system, the passenger side slidedoor and the ramp. Refer toEntervan II Features and Options(pages 2 and 3), and referencedsections in this manual foridentification and explanation ofEntervan features and functions.

Terminology: The term“KNEEL” appearing within thismanual and on operating instruc-tions decals is a reference to thelowering and raising motion of theEntervan electromechanical rear

suspension. The term “OPEN”indicates the opening motion ofthe power slide door, and“CLOSE” indicates the closingmotion of the power slide door.The term “UNFOLD” indicates thelowering motion of the ramp tothe deployed position. The term“FOLD” indicates the raisingmotion of the ramp to the vertical(stowed) position.

Contact The Braun Corporationimmediately if any of this informa-tion is not understood. Call 1-800-THE LIFT.

Read and becomefamiliar with all safetyprecautions, pre-operation notes anddetails, operatinginstructions andmanual operatinginstructions prior tooperation. ContactThe Braun Corpora-tion immediately ifthis information is notfully understood.Failure to do so mayresult in seriousbodily injury and/orproperty damage.

WARNING

Color Coding: Entervan IIinterior-mounted control switchesare color-coded and function-labeled to correspond to the colorcoding and switch-function labelsthat appear on the Power Opera-tion Instructions decal (posted onthe interior wall panel above thepower door operator).

The color of the symbol corre-sponds to the color of the switchto be used. Color coding appliesto the interior-mounted controlswitches only.

Triangular-shaped color-codedsymbols appear on the PowerOperation Instructions decal. Thedirection of the symbol corre-sponds with the direction theswitch should be activated(pressed) to produce the intended

Control Switches

function. = Press switch UP,and = press switch DOWN.

Although the remote controltransmitter OPEN and CLOSEswitches are not color-coded,the functions activated by remotecontrol transmitter OPEN andCLOSE switches are identical tothe functions activated by theinterior-mounted OPEN/CLOSEswitches.

The outside key entry activatesthe same functions as the interior-mounted yellow OPEN/CLOSEswitches and the remote controltransmitter OPEN and CLOSEswitches.

Control switch details are pro-vided in this section.

Do not activatecontrol switches whenanyone is near thearea in which dooroperates, rampoperates or vehiclekneels. Failure tofollow this rule mayresult in seriousbodily injury and/orproperty damage.

WARNING

Op

eration


Control Switches (continued)

Rear Wall-Mounted Control Switches

Control Switches(Detail Photo Below)

Black MANUAL/AUTO Switch

Press the black MANUAL/AUTOswitch to the MANUAL (up)position before performingManual Ramp Operating Proce-dures.

Press the black MANUAL/AUTOswitch to the AUTO (down)position before performingautomatic Power OperatingProcedures.

MANUAL/AUTO OverrideSwitch: This switch must bepressed to the AUTO positionbefore automatic (power) rampfunctions can be activated.Pressing this switch to theMANUAL position allows thepower ramp to be manuallyoperated in event of power orequipment failure. This switchmust be in the MANUAL positionwhen performing Manual RampOperating Procedures.

OPEN/CLOSE Switch: Thisswitch is identical to the dash-mounted OPEN/CLOSE switch inappearance and operation.

Yellow OPEN/CLOSE Switch

Press the yellow OPEN/CLOSEswitch to the CLOSE (up)position to fold (raise) the ramp,close the automatic door andactivate the “kneel” system*.

Press the yellow OPEN/CLOSEswitch to the OPEN (down)position to open the automaticdoor, unfold (lower) the ramp andactivate the “kneel” system*.

Yellow OPEN/CLOSE Switch

Press the yellow OPEN/CLOSEswitch to the CLOSE (up) posi-tion to fold (raise) the ramp, closethe automatic door and activatethe “kneel” system*.

Press the yellow OPEN/CLOSEswitch to the OPEN (down)position to open the automaticdoor, unfold (lower) the ramp andactivate the “kneel” system*.

Red KNEEL Switch:

Press the red KNEEL switch tothe YES (up) position to turnthe “kneel” system* on.

Press the red KNEEL switch tothe NO (down) position to turnthe “kneel” system* off.

Dash-Mounted Control Switches

* The KNEEL switch turns the“kneeling” system on and offonly. Pressing the OPEN/CLOSE switch automaticallyactivates the “kneeling” featureto lower the vehicle if the reddash-mounted KNEEL switchis in the YES (up) position.Pressing the CLOSE switchactivates the “kneeling” featureto raise the vehicle if the reddash-mounted KNEEL switchis in the YES (up) position.

See page 11 for overall view ofdash-mounted control switches.

Op

eration


The remote control OPEN andCLOSE switches activate thesame functions as the Entervan-mounted yellow OPEN/CLOSEswitches. Two mini remotecontrol transmitters (shown here)are supplied with all Entervans.

Press the OPEN switch to openthe automatic door and unfold(lower) the ramp. Note: Press-ing the OPEN switch also acti-vates the “kneeling” feature tolower the vehicle if the red dash-mounted KNEEL switch is in theYES (up) position.

Mini Remote Control Transmitter Switches

Note: A full size (larger) remotecontrol transmitter (shown below) isavailable as an option. Operationprocedures for both transmittersare identical. The remote controlsystem has an operating range of35 feet.

Press the CLOSE switch to fold(raise) the ramp and close theautomatic door. Note: Pressingthe CLOSE switch also activatesthe “kneeling” feature to raise thevehicle if the red dash-mountedKNEEL switch is in the YES (up)position.

WARNINGRead manual before operating. Do not operate this control unit with anyone on or near the area in which the ramp operates or the vehicle kneels (lowers). Failure to follow these rules may result in serious bodily injury and/or property damage.

19969

19968

OPEN CLOSE

Do not interface after-market control systems**with a Braun Entervan.

The remote control OPEN andCLOSE switches activate thesame functions as the Entervan-mounted yellow OPEN/CLOSEswitches. The full size remotecontrol transmitter (shown here)is available as an option only.

Press the OPEN switch to openthe automatic door and unfold(lower) the ramp. Note: Press-ing the OPEN switch also acti-vates the “kneeling” feature tolower the vehicle if the red dash-mounted KNEEL switch is in theYES (up) position.

Full Size Remote Control Transmitter (Option) Switches

Note: Two mini remote controltransmitters (shown above) aresupplied with all Entervans. Op-eration procedures for both trans-mitters are identical. The remotecontrol system has an operatingrange of 35 feet.

Press the CLOSE switch to fold(raise) the ramp and close theautomatic door. Note: Pressingthe CLOSE switch also activatesthe “kneeling” feature to raise thevehicle if the red dash-mountedKNEEL switch is in the YES (up)position.

WARNINGRead manual before operating. Donot operate this control unit withanyone on or near the area in whichthe ramp operates or the vehiclekneels (lowers). Failure to follow these rules may result in serious bodily injury and/or property damage.

Remote Control Unit

OPEN CLOSE18563

18564

ENTERTM

Do not interface after-market control systems**with a Braun Entervan.

Op

eration

The Braun Corporation manu-factures dedicated controlsystems for it's products (i.e.,wheelchair lifts, door operators,ramp systems, kneeling sys-tems). These control systemshave been designed and testedfor use in conjunction with

specific Braun products. Brauncontrol systems are the onlycontrol systems authorized foruse with Braun products.

Do not attempt to interface after-market control systems withBraun products. To do so may

result in serious bodily injuryand/or property damage.

For information about theproper control system for aspecific Braun product, contactThe Braun Corporation at 1-800-THE LIFT.

** Braun Corporation After-Market Control Systems Policy:


Passenger Door Outside Key Entry

Control Switches (continued)

An outside key entry is incorpo-rated in the passenger side frontdoor lock. The outside key entryactivates the same functions asthe interior-mounted yellowOPEN/CLOSE switches and theremote control transmitter OPENand CLOSE switches. Thevehicle OEM door key activatesthe outside key entry system aswell as operating the passengerdoor lock. See your Chryslerowner's manual for detailsregarding door locks.

OPEN: Insert the key and turn itclockwise (toward front of vehicle)to open the automatic door andunfold (lower) the ramp. Note:Turning the key clockwise alsoactivates the “kneeling” feature tolower the vehicle if the red dash-mounted KNEEL switch is in theYES (up) position.

CLOSE: Insert the key and turn itcounterclockwise (toward rear ofvehicle) to fold (raise) the rampand close the automatic door.Note: Turning the key counter-clockwise also activates the“kneeling” feature to raise thevehicle if the red dash-mountedKNEEL switch is in the YES (up)position.

CLOSEOPEN

Delay Feature: When activatingthe OPEN functions using theoutside key entry, the key unlocksthe door and then there is a twosecond delay before the Enter-van power functions are acti-vated. This delay feature onlyoccurs when activating theoutside key entry and only occursduring the OPEN function.

1. Press MANUAL/AUTO switch to MANUAL position.2. Pull detent pin.3. Pull red handled lever fully.4. Insert detent pin in lever hole.

Note: Pull detent pin, return lever to original position and press MANUAL/AUTO switch to AUTO position before performing electric procedures.

KNEEL ACTUATORMANUAL RELEASE

Use only if vehicle will not raise electrically.

52215

MANUAL

AUTO

MANUAL

AUTO

Kneel Actuator Manual ReleaseAssembly

Kneel Actuator MANUAL/AUTO Switch

The Kneel Actuator MANUAL/AUTO switch is mounted in theKneel Actuator Manual Releaseassembly. The Kneel ActuatorManual Release assembly islocated behind the driver's sideslide door. This switch must be

in the AUTO position before theelectromechanical power kneelingsystem can be activated. TheMANUAL/AUTO switch must bepressed to the MANUAL positionin order to manually release thekneel actuator.

Do not press this switch to theMANUAL position unless youhave experienced kneel actuatorpower or equipment failure. Seepages 23 and 24 for further details.

Kneel Actuator MANUAL/AUTO Switch

Press the black MANUAL/AUTOswitch to the MANUAL (up) positionbefore performing Kneel ActuatorManual Release Procedures.

Press the black MANUAL/AUTOswitch to the AUTO (down)position before performing auto-matic Power Kneeling Operations.

Op

eration

MANUAL/AUTOOverride Switch


Whenever parking yourEntervan and before utilizingany Entervan features, alwaysengage the vehicle transmis-sion in Park “P” and engagethe vehicle parking brake.

Transmission: The vehicletransmission must be engagedin Park “P,” before operatingthe Entervan automatic fea-tures. Entervan power functioncontrol switches cannot beactivated if the vehicle transmis-sion is not in Park.

MANUAL/AUTO OverrideSwitch: The MANUAL/AUTO

override switch must bepressed to the AUTOposition before the auto-matic ramp can be acti-vated. This switch islocated on the passenger-side interior wall panel,above the power dooroperator as shown at right.See Control Switches onpage 8 also.

Kneel Actuator MANUAL/AUTO Switch: The KneelActuator MANUAL/AUTOswitch must be pressed to theAUTO position before the electro-mechanical “kneeling” system can

Kneeling Feature

Red Kneel Switch

The red dash-mounted KNEELswitch turns the “kneeling” systemon and off. This switch providesthe option of kneeling the vehiclewhen operating the power doorand power ramp. The optional“kneeling” feature can only beturned on and off by the dash-mounted red KNEEL switch. SeeControl Switches on page 8.

Press the red KNEEL switch tothe YES position to turn the“kneel” system on. Press the redKNEEL switch to the NO positionto turn the “kneel” system off.With the KNEEL switch in theYES position, the rear of thevehicle will automatically lowerwhen either of the two interior-mounted yellow OPEN/CLOSEswitches is pressed to the OPENposition for two seconds orlonger.

Delay Feature: The OPENswitch must be pressed for twoseconds or longer before the“kneel” system is activated. Oncethe “kneel” system is activated,

be activated. See photos anddetails on opposite page.

“Kneeling” is the lowering andraising motion of the Entervanelectromechanical rear suspen-sion. The kneel feature lowersthe rear of the vehicle. See thephotos on page 2.

The Entervan operator has theoption of using the kneelfeature or not. Activating thekneel feature to lower the rearof the vehicle reduces the slopeof the ramp when deployed.

WARNING

Keep clear of areain which the vehiclekneels (lowers).Failure to do so mayresult in seriousbodily injury.

Do not activate the kneelsystem when anyone is nearthe underside of the vehicle.Kneel (lower) the Entervanon level surfaces only.

the rear of the Entervan will con-tinue to lower regardless if one ofthe control switches is continued tobe pressed.

Pressing the remote control OPENswitch or turning the passengerdoor outside key entry key clock-wise (toward front of vehicle)activates the “kneel” function in thesame manner.

Op

eration

WARNING

Driving an Entervanin the kneeled (low-ered) position mayresult in seriousbodily injury and/orproperty damage.


WARNING

Keep clear of area inwhich the dooroperates. Failure todo so may result inserious bodily injury.

Keep clear of areain which the auto-matic power dooroperates. Becertain no person orobstruction is withinthe path of the doorwhen opening orclosing the door.

Keep children clear of the door and ramp paths(operating areas) during door and ramp opera-tion. Keep body parts and obstructions clear ofarea in which door operates. Keep clear of allpower door moving parts. Do not place anybody part or obstruction in the path of theautomatic door, the door gear rack or otherpower door moving parts. Do not attempt togrip or hold the door or door gear rack.

The automatic door can be activated by eitherinterior-mounted yellow OPEN/CLOSE switch, theremote control switches or the passenger dooroutside key entry. See pages 7-9 for further detailsregarding these Entervan controls.

You must continue to press the OPEN switch orturn the outside key entry key clockwise throughoutthe entire door opening function (until the doorstops - opens fully). You must continue to pressthe CLOSE switch or turn the outside key entry keycounterclockwise throughout the entire door closingfunction to close the door fully.

Manual Operation: If you experience power orequipment failure, refer to the Door and RampManual Operating Instructions on pages 21 and 22.

Automatic Power Door

When the red KNEEL switch is in the YES position,the vehicle will automatically raise when either of thetwo Entervan-mounted yellow OPEN/CLOSEswitches are pressed to the CLOSE position.Pressing the remote control CLOSE switch orturning the passenger door outside key entry keycounterclockwise (toward rear of vehicle) activatesthe “kneel” function to raise the rear of the Entervanin the same manner.

Note: If the vehicle is in the kneeled position andthe red KNEEL switch is pressed to the NO position,the rear of the vehicle will raise automatically. Donot press the KNEEL switch to the NO positionwhen a wheelchair passenger is on the ramp!

Out-of-Park Kneeling Override: If the Entervan isin the kneeled position and the vehicle transmissionis disengaged from Park “P,” the rear of the vehiclewill automatically raise. This feature eliminatesthe possibility of unintentionally driving the Entervanwith the rear of the vehicle in the lowered position.When the transmission is disengaged from Park, thekneel actuator is electrically activated. Whenactivated, the actuator shaft extends to raise therear of the vehicle to the normal position. Do notdisengage the transmission from Park when a

Kneeling Feature (continued)

wheelchair passenger is on the ramp!

Mechanical Kneeling Override: In the event thatthe Entervan is in the kneeled position and youexperience power or equipment failure, the KneelActuator Manual Release (Override) feature allowsthe rear of the vehicle to be raised to the normalposition. Further details and Kneel Actuator ManualRelease Instructions are provided on pages 23 and24.

Do not continue todrive the Entervanwith the rear of thevehicle in the loweredposition. Attemptingto drive the Entervanwith the rear of thevehicle in the loweredposition will result in anextremely rough andunstable ride, andcould possibly result in injury and/or vehicledamage. The vehicle would ride as if it did not haveany rear suspension. In the event of a kneelsystem failure, have the kneel system repairedimmediately.

Op

eration


Automatic Power Ramp

WARNINGBe certain there isadequate clearanceoutside the Entervanbefore unfolding theautomatic ramp.Approximately 56inches clearancemust be provided toaccommodate theramp.

Provide adequateclearance outside ofvehicle to accom-modate ramp.Failure to do so mayresult in seriousbodily injury and/orproperty damage.

Keep clear of area in which the automatic powerramp operates. Be certain no person or obstruc-tion is within the path of the ramp when unfolding orfolding the ramp.

Keep all passengers and bystanders clear of thearea in which the ramp unfolds and folds (inside andoutside the vehicle). Keep children clear of theramp path (operating area) during ramp opera-tion. When inside the vehicle, all non-wheelchairpassengers should be seated and restrained usingthe Chrysler-equipped (OEM) seat belts as detailed

Do not grip or holdramp fold arm!

in your Chrysler-supplied owner's manual. Wheel-chair passengers must be positioned and restrainedas detailed in the Wheelchair and Occupant Re-straint instructions on pages 25-29. Properly seatedand restained passengers will be clear of rampmovement.

Keep body parts and obstructions clear of thearea in which the ramp operates. Keep clear ofall power ramp moving parts. Do not attempt togrip or hold the ramp or ramp folding mecha-nism (fold arm and bearing assembly).

WARNINGKeep clear of area in which ramp operates.

52205

WARNINGKeep body parts and obstructions clear of area in which ramp operates.

52206


52207

Wall

Keep clear of the areain which the ramp foldsinto the door opening.

Op

eration


WARNINGClose slide door before loading and unloading wheelchair passengers.

52208

Door

Driver Side Slide Door

Close the driver-side slide door before loadingand unloading wheelchair passengers. Operatethis slide door as detailed in your Chrysler-suppliedowner's manual. To provide a safer environment forsmall children and wheelchair passengers, activatethe Child Protection Door Lock as outlined in yourChrysler-supplied manual. When the child locksystem is engaged, the door can only be openedfrom the outside. Always make sure the sliding dooris fully latched any time the vehicle is in motion.

Close the driver-side slide doorbefore loading and unloadingwheelchair passengers!

The automatic ramp can be activated by eitherinterior-mounted yellow OPEN/CLOSE switch, theremote control switches or the outside key entry.See pages 7-10 for further details regarding theseEntervan controls.

Delay Feature: After the door is fully open, aminimum two second delay will occur before theramp starts to unfold. This delay feature is requiredin order to utilize the Passive (Non-Wheelchair)Access feature. The delay allows the operatoradequate time to release the OPEN switch once thedoor is open - preventing the automatic rampunfolding operation from starting. The ramp assem-bly can then be manually rotated out of the vehicleallowing passive (non-wheelchair) access to thedoor opening if so desired. See page 19 for Pas-sive (Non-Wheelchair) Access details.

Ramp Unfolding Notes: When unfolding the ramp,the ramp motor stops running when the rampreaches the nearly-horizontal position (approxi-mately 6" - 8" above ground level). The ramp

continues to slowly lower the remaining distanceby the force of gravity.

When the ramp has unfolded beyond the vertical(90°) position and you stop activating the DOWNfunction, the ramp may continue to unfold veryslowly. This gravity-activated unfolding of the rampmay not be visibly detected until an approximate 75°angle is reached.

Ramp Folding Note: You must continue to pressthe CLOSE switch or turn the outside key entry keycounterclockwise through the entire ramp foldingfunction to fold the ramp fully (stowed position). Ifthe ramp has not folded fully (beyond vertical - 90°position) and you stop activating the CLOSE func-tion, the ramp may unfold (deploy) by the force ofgravity as explained above.

Manual Operation: If you experience power orequipment failure, refer to the Door and RampManual Operating Instructions on pages 21 and22.

Automatic Power Ramp (continued)Op

eration


Op

eration

Ramp Safety

Wheelchair passengers and attendants (whenapplicable), must use basic common sense andgood judgement regarding ramp safety. The BraunCorporation recognizes that each wheelchairpassenger has a unique set of physical abilitiescombined with the physical characteristics of his orher wheelchair that dictate the method in which heor she will enter and exit their Entervan. Conse-quently, the procedures for safe operation outlinedin this manual are general in nature.

Follow all safety instructions regarding torso re-straints, stability, balance, weight distribution anduse of attendants as specified in the owner's manualsupplied with your wheelchair. Determine, establish

and practice ramp boarding and exiting proceduresunder the direction of your health care professional,your wheelchair representative, and your Entervansales representative (dealer) to ensure your abilityto do so safely.

Never board an Entervan ramp if you or yourattendant are intoxicated. The wheelchair must bepositioned in the center of the ramp at all times.You must be able to clearly view the ramp wheneverboarding and and exiting the vehicle.

It is the responsibility of the wheelchair operatorto enter and exit the Entervan on the ramp in thesafest manner.

Stabilizing Wheelchairs

Powered and manual wheelchairs are designed toremain upright and stable during normal operation.All activities which involve movement in a wheel-chair have an effect on the combined center ofgravity of the occupant and wheelchair. Be awareof the Entervan ramp slope (angle). The slope of

the ramp has a direct effect on the center of gravity.Keep in mind your center of gravity and your abilityto maintain stability and balance.

Do not operate your wheelchair on the Entervanramp without assistance if your are unable to

WARNINGBe aware oframp slope.

52217

maintain stability and balance.Counterbalance devices (anti-tippers) may be available fromyour wheelchair representativeto enhance stability andbalance.

Do not tilt your wheelchairwithout assistance. Operatethe wheelchair at a slow andconstant speed when on the

WARNING

Position and secure(buckle, engage,fasten, etc.) thewheelchair-equippedoccupant seat beltbefore loading ontothe wheelchair ramp.Failure to do so mayresult in seriousbodily injury and/orproperty damage.

Different types of disabilities require different typesof wheelchairs and different types of wheelchair-equipped occupant restraint belt systems (torsorestraint). It is the responsibility of the wheelchairpassenger to have his or her wheelchair equippedwith an occupant restraint (seat belt) under thedirection of their health care professional.

Wheelchair attendants should be instructed on anyspecial needs and/or procedures required for safetransport of wheelchair passengers.

The Braun Corpora-tion recommendswheelchair passen-gers position andbuckle their wheel-chair-equipped seatbelt (torso restraint),as specified by themanufacturer, beforeloading onto awheelchair ramp.

Wheelchair-Equipped Occupant Seat Belts

Op

eration


Stabilizing Wheelchairs (continued)


52217

ramp. Do not acceleratesuddenly when on the ramp.Do not raise the front wheel-chair wheels (pull wheelie)when on the Entervan ramp.

The aid of an attendant stabiliz-ing the wheelchair is recom-mended for optimum safety.Wheelchair passengers whointend to enter and exit theirEntervan without the assistance of an attendantmust determine the safest and most practicalmethod and orientation of entering and exiting theEntervan based on the physical characteristics oftheir personal wheelchair and his or her physicalcapabilities to maintain stability while the wheelchairis in motion on the Entervan ramp.

It is the responsibility of the wheelchair operatorto enter and exit the Entervan on the ramp in thesafest manner.

attendant must graspthe push handles (orother) securely.Detachable wheel-chair parts such asarms or legrests mustnever be used forhand holds or liftingsupports. Doing socould result in thedetachable partsbeing inadvertentlydetached from the

WARNING

Do not grip detach-able wheelchair partswhen assisting tostabilize wheelchair.Doing so may resultin serious bodilyinjury and/or propertydamage.

wheelchair resulting in possible injury to thewheelchair occupant and/or the attendant.

Wheelchair Attendants: When assisting a wheel-chair occupant, remember to use good body me-chanics. Keep your back straight and bend yourknees. When the wheelchair is on the ramp, the

The Braun Corporation recommends wheelchairpassengers and their attendant(s) review thematerial contained in this manual with your Entervansales representative (dealer), before attemptingoperation. Any questions or concerns can beanswered by your dealer at that time.

Using your own wheelchair and personal atten-dant (if applicable), operate the Entervan through all

Operation Procedure Review

functions and enter and exit the vehicle with yourdealer on hand to ensure the Entervan is right foryou as the end user, (applicable for your use basedon your physical abilities and the physical character-istics of your personal wheelchair). Practice usingthe wheelchair and occupant belt/track system withyour sales representative on hand. Become familiarwith the proper operation of all Entervan features.

Wheelchair Orientation and Securement During Transport:

The wheelchair and occupant must face the front ofthe vehicle and must be secured using the For-ward-Facing Wheelchair and Occupant Belt/

Track System when riding in the Entervan. Seepages 25-29 for Wheelchair and Occupant Re-straint details.

Op

eration


Preventive maintenance consisting of carefulinspections of your Entervan systems should be apart of your routine. Simple inspections can detectpotential kneel, door or ramp malfunctions. Regularpreventive maintenance evaluations will reducepotential operation down time and increase theservice life of the Entervan, as well as enhancingsafety. During routine inspections, operate allEntervan systems and note the following:

• Do the control switches function properly?• Does the kneel feature function properly?• Does the automatic door function properly?• Does the automatic ramp unfold and fold properly?• Is the power source adequate or weak?

Inspect the wheelchair and occupant restraint belts,buckles and hardware. If there is any sign ofdamage, wear, abnormal condition or improperoperation, discontinue Entervan use immediately.Contact your dealer or call The Braun Corporation at

Preventive Maintenance

1-800-THE LIFT. One of our national servicerepresentatives will direct you to an authorizedservice repairman who will inspect your Entervan.

Preventive maintenance visual inspections do nottake the place of the procedures specified in theMaintenance/Lubrication Schedule. The proceduresoutlined in the detailed Maintenance/LubricationSchedule provided in this manual must be per-formed at the recommended scheduled intervals.

Exposure to harsh weather elements or environmen-tal conditions may reduce the service life of Entervansystems. Road salt used to melt snow and ice innorthern climates as well as salt water climates tendto corrode components more rapidly. Extreme dustyor sandy conditions can cause contamination andreduce the effectiveness of lubrication. If yourEntervan is exposed to these types of harsh condi-tions, have your maintenance and lubricationprocedures performed often.

Opening the power slide door using either interior-mounted yellow OPEN/CLOSE switch or using theremote control OPEN switch does not disarm theChrysler factory-equipped (OEM) Anti-Theft System(if equipped). If you open the power slide doorusing one of these Entervan controls before unlock-ing a vehicle door, the alarm system will betriggered.

Always disarm the alarm system before opening

Door Locks and Anti-Theft (Alarm) System

the power slide door. You can disarm the alarmsystem by unlocking the driver door, front passengerdoor or liftgate with the door key. You can alsodisarm the system by pressing the OEM remotekeyless entry transmitter UNLOCK button.

See your Chrysler-supplied (OEM) owner’s manualfor further details regarding the Remote KeylessEntry System (if equipped) and the Anti-TheftSystem (if equipped).

Entervan II Power Operating Instructions

TO FOLD RAMP AND CLOSE DOOR:

Press the CLOSE switch or turn the Outside KeyEntry key counterclockwise until the ramp foldsfully and the door closes fully.

Note: You must continue to press the CLOSEswitch or turn the Outside Key Entry key counter-clockwise through the entire ramp folding anddoor closing functions.

TO TURN POWER KNEELING OFF:

Press the red KNEEL switch to the NO (down)position.

FOR POWER KNEELING:

Press the red KNEEL switch to the YES (up)position. Note: See Kneeling Delay above.

TO OPEN DOOR AND UNFOLD RAMP:

Press the OPEN switch or turn the PassengerDoor Outside Key Entry key clockwise until thedoor opens fully and the ramp unfolds fully.Release switch or key. Note: See Key EntryDelay above.

Note: After the door is fully open, a minimumtwo second delay will occur before the rampstarts to unfold. Note: See Ramp Delay above.

Note: Engage the vehicle transmission in“Park,” engage the vehicle parking brake andpress the MANUAL/AUTO override switch tothe AUTO position before operation.

Op

eration Read and become

familiar with all safetyprecautions, pre-operation notes anddetails, operatinginstructions andmanual operatinginstructions beforeoperation. Failure todo so may result inserious bodily injuryand/or propertydamage.

WARNINGWARNINGBe aware oframp slope.

52217

The instructions provided below outline the step-by-step procedures required to operate the automatickneel, door and ramp systems. These instructionsalso appear on Power Operation instructions decal#52211 (posted on the interior wall panel above thepower ramp motor assembly).

Review the Pre-Operation Notes and Detailssection for detailed information regarding all

Entervan controlswitches, functions andoperating procedures.

Manual Instructions:Refer to the ManualOperating Instructionson pages 21-24 if you experience power or equip-ment failure.

Kneeling Delay: The red dash-mounted KNEELswitch turns the “kneeling” system on and off. Therear of the vehicle will automatically “kneel” (lower)when one of the OPEN controls is activated for twoseconds or longer. The OPEN control must beactivated for two seconds or longer before the“kneel” system lower function is activated. Seepages 11 and 12 for further details.

Ramp Delay: After the door is fully open, a mini-mum two second delay will occur before the rampstarts to unfold. See Passive (Non-Wheelchair)Access on the following page for further details.

Key Entry Delay: When activating OPEN functionsusing the outside key entry, the key unlocks thedoor and then there is a two second delay beforethe Entervan power functions are activated.

When in the stowed (folded)position, the ramp assembly canbe manually rotated out of theslide door opening. This featureallows passive (non-wheelchair)access to the passenger sideslide door opening when desired.The ramp assembly can also bemanually removed (details onfollowing page).

The ramp assembly pivots(rotates) on two axles (top andbottom) when the ramp latch isdisengaged. The front of theramp is secured to the vehiclefloor with a cable activatedspring-loaded latch.

The ramp latch is located at floorlevel at the front of the ramp (seePhoto B). The latch is activatedby a release cable. The release

Passive (Non-Wheelchair) Access Instructions

ARelease Knobcable is routed upward throughthe front slide door post interiorpanel. The cable is equippedwith a knob for use as a latchrelease handle (see Photo A).The knob is located adjacent tothe front top corner of the ramp(when ramp is in stowed posi-tion).

Open the door fully beforemanually rotating ramp. Re-lease the OPEN switch as soonthe door is fully open.

Delay Feature: After the door isfully open, a minimum two seconddelay will occur before the rampstarts to unfold. The delay allowsthe operator adequate time torelease the OPEN switch (oroutside key entry), once the dooris open - preventing the automaticramp from unfolding.

Do not attempt to fold or unfoldthe ramp when the latch isdisengaged or the ramp is inthe passive position (rotated outof vehicle).

The instructions provided belowoutline the step-by-step proce-dures required to manually rotatethe ramp. These instructions alsoappear on Passive (Non-Wheel-chair) Access Instructions decal#18515 (posted on the front slidedoor post interior wall paneladjacent to the release knob).

CAUTION

• Open door fullybefore rotating ramp.

• Do not fold or unfoldramp when ramplatch is disengagedor ramp is in passiveposition (rotated outof vehicle).

Failure to follow theserules may result inpersonal injury and/orproperty damage.

C

B

For Passive (Non-Wheelchair) Access:

1. Press the OPEN switch or turn the Outside KeyEntry key clockwise until the door opens fully.Release switch or key (see Delay Feature above).

2. Pull cable knob UP fully to unlatch ramp. SeePhoto A.

3. Manually rotate ramp OUT. See Photo C. Se-cure and support the ramp during passengeraccess. Caution: Do not force ramp open. Donot attempt to activate the power ramp when inthe passive position (rotated out of vehicle).

To Store Ramp and Close Door:

1. Manually rotate ramp IN fully to latch ramp.

2. Press the CLOSE switch or turn the Outside KeyEntry key counterclockwise until the door closesfully.

Ramp Latch

Ramp

Op

eration

Ramp Removal Instructions

When in the stowed (folded)position, the ramp and motorassembly can be manuallyremoved from the vehicle. Openthe door fully before manuallyremoving the ramp. Releasethe OPEN switch (or outsidekey entry), as soon as the dooris fully open.

The front of the ramp is securedto the vehicle floor with the cableactivated Passive Access latch.The latch must be disengaged inorder to remove the ramp. Seeprevious page for PassiveAccess details and photos.

D

Jumper (loose)

Ramp Wiring HarnessConnected

RampMotor

Ramp Wiring HarnessDisconnected

9-Circuit Sockets

The rear of the ramp and motor assembly is secured to the reardoor post with a hairpin cotter. See Photo F. The hairpin cottermust be removed in order to remove the ramp.

CAUTION

Disconnect rampmotor wiring harnessbefore removing ramp.Failure to do so willresult in damage.

Disconnect the ramp motorharness before removing theramp. Failure to do so will resultin damage. The power ramp motorelectrical wiring harness is locatedwithin the interior wall panel by theramp motor as shown in Photos Dand E. Depress the locking tabs todisconnect the 9-circuit sockets.

Note: A jumper wire assembly is attached to the main wiringharness. Install the jumper wire 9-circuit socket in the mainharness 9-circuit socket that the ramp motor harness was con-nected to. See Photos D and E. Connecting the jumper wireprovides power to the door operator when the ramp is removed.

The instructions provided below outline the step-by-step proce-dures required to manually remove the ramp.

G

Flat washer positions on floor rotationaxle.

Hairpin Cotter

Ramp Motor Assembly

F

Ramp Removal Instructions:

1. Press the OPEN switch or turn the Outside KeyEntry key clockwise until the door opens fully.Release switch or key.

2. Disconnect the ramp electrical wiring harness.See Photo D. Note: It may be necessary topartially rotate the ramp to access the wiringharness and jumper wire.

3. Connect the jumper wire to the main electricalharness. See Photo E.

E

Note: Ramp rotated for clear viewof wiring harness and jumper wirein Photos D and E.

Jumper (installed)Main Harness

SocketOp

eration

Ramp Removal Instructions

Ramp Removal Instructions (continued):

3. Remove the hairpin cotter from the top ramp pivotaxle. See Photo F on previous page.

Note: Keep the hairpin cotter when removing theramp. The hairpin cotter must be repositionedwhen reinstalling the ramp assembly.

4. Pull release knob UP fully to unlatch ramp. SeePhoto A on page 19.

5. Grip both sides of the ramp assembly and lift up.Manually remove ramp. See Photo G on previ-ous page. Use good body mechanics when

removing the ramp. Keep your back straight andbend your knees when lifting the ramp.

Note: Keep the flat washer positioned on thefloor rotation axle when removing the ramp. Thewasher must be repositioned when reinstallingthe ramp assembly. See Photo G.

Reverse procedures to install ramp.

Note: Be certain the flat washer and hairpincotter are repositioned when reinstalling the rampassembly.

Door and Ramp Manual Operating Instructions

WARNING

• Clear ramp pathbefore performingmanual unfoldprocedures. Rampwill free-fall.

• Be certain door isfully open.

• Keep clear ofmoving parts.

Failure to followthese rules mayresult in seriousbodily injury and/orproperty damage.


52205

performing manual ramp operatingprocedures. Keep your backstraight and bend your knees whenfolding (lifting) the ramp.

Operate door and/or rampmanually ONLY if either cannotbe operated electrically.

MANUAL/AUTO Switch Release Handle

Notes: The vehicletransmission must beengaged in Park “P” andthe parking brake must beengaged before perform-ing all manual operationprocedures.

The MANUAL/AUTOswitch must be in theMANUAL position beforeperforming manual rampoperation procedures.

If you experience power or equip-ment failure, refer to the step-by-stepinstructions on the following page tomanually operate the slide door andramp. Manual operation instructionsalso appear on Manual Operationinstructions decal #52212 (posted onthe power ramp motor housing).

Note: It is recommended to have anassistant aid in performing manualoperating procedures. Many wheel-chair passengers will not be able toperform manual operating proce-dures. An assistant may be re-quired.

Use good body mechanics when

A red manual door releasehandle is located rear of thepower ramp as shown. In theevent you experience poweror equipment failure, the slidedoor can be opened manually.Pull red manual door releasehandle UP fully to release(disengage) the door opera-tor. Push the release handleDOWN fully to re-engage thedoor operator.

Op

eration

Door and Ramp Manual Operating Instructions

WARNING

• Clear ramp pathbefore performingmanual unfoldprocedures. Rampwill free-fall.

• Be certain door isfully open.

• Keep clear ofmoving parts.

Failure to followthese rules mayresult in seriousbodily injury and/orproperty damage.

The power ramp cannot beactivated unless the MANUAL/AUTO switch is in the AUTO(down) position.

Note: The MANUAL/AUTOswitch must be pressed to theAUTO (down) position beforeperforming electric procedures.

FOLD

UN

FOL

D

A

C

D

Access Hole

Gear Rack

ENGAGE

RE

LE

AS

E

TO UNFOLD RAMP:

1. Clear the ramp path! Note: The ramp path must be clear.The ramp will free-fall when pushed out. An assistant shouldcarefully unfold and lower the ramp to the ground from outsidethe vehicle if possible (Photo C).

2. Push top of ramp out (if an assistant is not available only). SeePhoto B.

TO FOLD RAMP:

Carefully lift and fold the ramp fully (to stowed position). SeePhoto C. Note: Remember to use good body mechanics. Assis-tants should keep their back straight and bend knees when lifting.Lift from the outboard end of the ramp. Keep body parts andobstructions clear of the area in which the ramp operates.

TO CLOSE DOOR(To Re-engage Door Operator):

1. Pull red manual door release handle UP fully. See Photo A.2. Carefully manually close door fully. Note: Be certain the power

door gear rack enters (aligns with) the access hole located in thedoor opening front door post when closing the door (Photo D).

3. Push red manual door release handle DOWN fully to securedoor. See Photo A. Note: It may be necessary for an assistantto close the door tight from outside the vehicle while engagingthe release handle.

Push ramp out if an assistant is notavailable ONLY!

B

Note: Engage vehicle transmissionin Park,engage vehicle parkingbrake and press MANUAL/AUTOswitch to the MANUAL positionbefore performing manual rampoperation procedures.

Read page 21 before proceeding!

TO OPEN DOOR(To Disengage Door Operator):

1. Pull red manual door releasehandle UP fully. See Photo A.

2. Manually open door fully.3. Push red manual door release

handle DOWN fully to secure door.See Photo A. Note: It may benecessary to push the door to therear while simultaneously securingthe door with the handle.

Op

eration

WARNING


Press kneel actuatorMANUAL/AUTOswitch to MANUAL(up) position beforepulling the kneelactuator manualrelease lever. Failureto do so may result inproperty damage.

CAUTION

Kneel Actuator Manual Release Instructions

Mechanical Kneeling Override: A manual releasefeature is built into the electric actuator-poweredelectromechanical kneel system. In the event thatthe Entervan is in the kneeled position and youexperience power or equipment failure, the KneelActuator Manual Release feature allows the rear ofthe vehicle to raise to the normal position.

Manual Release Lever: A red-handled kneelactuator manual release lever protrudes out of thedriver side interior wall panel rear of the sliding door.A detent pin is inserted in the release handle. Referto the instructions provided on the following pageand appearing on Kneel Actuator Manual ReleaseInstructions decal #52215 to manually release(override) the kneel actuator.

In the event that theEntervan is in thekneeled position andyou experiencepower or equipmentfailure, do notcontinue to drivethe Entervan withthe rear of thevehicle in thelowered position.

The kneeling system is powered by an electricactuator that compresses the rear suspension whenthe actuator is retracted. The electric brake builtinto the actuator is mechanically released when thered-handled kneel actuator manual release lever ispulled. A cable is attached to the release handlewhich mechanically releases the actuator brake.When the actuator brake is released, the suspen-sion leaf springs override the actuator, resulting inthe rear of the vehicle raising.

The kneel actuatorMANUAL/AUTOswitch must bepressed to theMANUAL (up)position in order tomanually release theactuator. If the switchis not in the MANUAL(up) position, therewill be too muchphysical resistance toaccomplish themanual release.

KneelActuatorRelease

Lever

DetentPin

Kneel Actuator Manual ReleaseInstructions Decal #52215





52215

Press the black MANUAL/AUTO switch tothe MANUAL (up) position before performingKneel Actuator Manual Release Procedures.

Press the black MANUAL/AUTO switch tothe AUTO (down) position before performingAutomatic Power Kneeling Operations.

Kneel ActuatorBlack MANUAL/AUTO Switch

Use Kneel Actuator Manual Release ONLYif the vehicle will not raise electrically.

MANUAL

AUTO

Do not attempt to manually release the kneelactuator if you have not experienced power orequipment failure. Damage to the manualrelease system could occur.

Note: Press the MANUAL/AUTO switch to AUTO(down) position before performing electricalprocedures. The electric actuator-powered electro-mechanical Kneel system cannot be activated if theKneel Actuator MANUAL/AUTO switch is not in theAUTO (down) position.

Attempting to drive the Entervan with the rear of thevehicle in the lowered position will result in anextremely rough and unstable ride, and couldpossibly result in injury and/or vehicle damage.The vehicle would ride as if it did not have any rearsuspension. In the event of a kneel systemfailure, have the kneel system repaired immedi-ately. Contact your dealer or call 1-800-THE LIFT.One of our national service representatives willdirect you to an authorized service repairman whowill inspect your Entervan.

Op

eration

Kneel Actuator Manual Release Instructions

In the event that the Entervan is in the kneeledposition and you experience power or equipmentfailure, refer to the instructions provided below andon Kneel Actuator Manual Release Instructions

Kneel Actuator Release Lever in Normal Position.





52215

3

4

Detent Pin Kneel ActuatorRelease Lever

1

A

B

C

2

Do not attempt tomanually release thekneel actuator if youhave not experiencedpower or equipmentfailure. Damage tothe manual releasesystem could occur.See previous page forfurther details.

Press kneel actuatorMANUAL/AUTOswitch to MANUAL(up) position beforepulling the kneelactuator manualrelease lever. Failureto do so may result inproperty damage.

CAUTION

decal #52215 tomanually release(override) the kneelactuator (raise therear of the vehicle tothe normal position).

Kneel ActuatorMANUAL/AUTO

Switch

Note: Pull detent pin, return lever tooriginal position, insert detent pinand press the Kneel MANUAL/AUTOswitch to AUTO (down) positionbefore performing electricalprocedures.

Read page 23 before performingthis procedure!

1. Press Kneel Actuator MANUAL/AUTOswitch to MANUAL (up) position. SeePhoto A.

2. Pull to remove the ringed-detent pininserted in the release lever. SeePhoto B.

3. Pull the red-handled lever fullyrearward. See Photo C.

4. Insert the detent pin in the holelocated in the lever. See Photo C.

Use the Kneel Manual Release ONLY ifthe vehicle will not raise electrically.

Kneel ActuatorManual Release Instructions

MANUAL

AUTO

WARNING


Op

eration


Wheelchair passengersshown depict theavailable wheelchairseating positions.Wheelchair capacity atMid-Point (Position C)may have limitationsbased on the physicaldimensions of specificwheelchairs.



BA

C

One Forward-Facing Wheelchair and Occupant Belt/Track System is supplied with the Entervan II. Thissystem is provided for the restraint of one wheelchairand occupant only. Note: The Entervan can accom-modate more than one wheelchair passenger (asshown above). Additional Forward-Facing Tie-DownBelt Kits must be purchased for restraint of eachadditional wheelchair passenger. Note: Wheelchairpassengers shown depict the available seating posi-tions. Wheelchair capacity at Mid-Point (Position C)may have limitations based on the physical dimensionsof specific wheelchairs.

The Forward-Facing Wheelchair and Occupant Belt/Track System consists of:

1. “A” track mounted in the vehicle (three locationsshown above) to be used in conjunction with theForward-Facing Wheelchair and Occupant beltssupplied.

2. Forward-Facing Wheelchair and Occupant Belt Kit#51140A — consisting of:

• Two adjustable over-center buckle belts forsecurement of the rear of the wheelchair.

• Two adjustable cam buckle belts for securement ofthe front of the wheelchair.

• One adjustable lap belt equipped with one “E” clipwhich installs in the vehicle-mounted “A” track andone female buckle receptacle. This lap belt isused in conjunction with the vehicle factory-equipped (OEM) upper torso shoulder harness.

Refer to the following guidelines, illustrations and theBelt Attachment Instructions on pages 26 through 29for proper use of the Forward-Facing Wheelchair andOccupant Belt/Track System.

Forward-Facing Wheelchair and Occupant Belt/Track System

Note: See page 3 for photos of horizontal “A” trackin the Front Lowered Floor Area (Position B) andthe Mid-Point Lowered Floor Area (Position C).

The Entervan II offers the following options forplacement and securement of wheelchairpassengers.

Quick-Release Driver Seat: This seat(Position A) can be removed and adaptivedriving systems custom tailored for the drivingwheelchair occupant can be purchased fromand installed by your local dealer. See pages30 and 31 for seat removal and installationinstructions.

Quick-Release Front Passenger Seat withFloor Track for Wheelchair and OccupantSecurement: This seat (Position B) can beremoved and the seat location can be utililizedby a wheelchair occupant. The wheelchairoccupant must be secured using the Forward-Facing Wheelchair and Occupant Belt/TrackSystem provided (detailed below).

Floor Track for Wheelchair and OccupantSecurement in Mid-Point Lowered FloorArea: The Mid-Point lowered floor area(Position C) can be utililized by wheelchairoccupant(s). The wheelchair occupant mustbe secured using the Forward-Facing Wheel-chair and Occupant Belt/Track Systemprovided (detailed below).

One Forward-Facing Wheelchair andOccupant Belt/Track System (detailedbelow) is supplied with the Entervan II. Thissystem is provided for the restraint of onewheelchair and occupant only.

Op

eration

No product developed todate can guaranteesuccessful securementof the wheelchair, evenat low speeds, in theevent of an accident.The Braun Wheelchairand Occupant Belt/TrackSystem does meet themost widely referencedFederal Motor VehicleSafety Standards usedfor contemporaryrestraint equipment.However, this equipmentdoes not ensure stabilityof the wheelchair in theevent of an accident atany speed.

Read and becomefamiliar with all Forward-Facing Wheelchair andOccupant Belt/TrackSystem instructions asspecified in this manualprior to installation oroperation procedures. Ifthe instructions are notfully understood,contact The BraunCorporation immedi-ately. Failure to do somay result in propertydamage, serious bodilyinjury and/or death.

Note: This informationis not all inclusive andwill not cover everywheelchair installation.Each wheelchair mustbe carefully andindividually fitted,reviewed and tested toprovide maximumcomfort and protectionfor the end user.


WARNING WARNING WARNINGWhen using wheelchairrestraints not suppliedwith the Entervan, readand become familiarwith all installation andoperation instructionssupplied with yourparticular wheelchairrestraint system prior toinstallation or operationprocedures. If theinstructions are not fullyunderstood, contact themanufacturer immedi-ately. Failure to do somay result in propertydamage, serious bodilyinjury and/or death.

Instructions on page 28, (Steps 2 and 3).

C. Proper position of lap belt track attachments is withrelease keeper toward the rear away from wheelchair.

Wheelchair Securement

Two adjustable over-center buckle belts are providedfor securement of the rear of the wheelchair. Twoadjustable cam buckle belts are provided forsecurement of the front of the wheelchair. Refer to theillustrations on page 27 and the Belt AttachmentInstructions on pages 28 and 29 .

Belt Maintenance

Inspect seat belt assemblies frequently during time inservice to evaluate system for belt wear. Any defectssuch as belt cut, fraying or malfunctioning call forreplacement of the entire system including belt, buckleand hardware.

Any seat belt system exposed to environmentalconditions or climates such as dirt, mud, oil, sand,cement, and grease will severely reduce the life of thesystem. Extreme care must be taken in the inspectionof a system exposed to these conditions. The replace-ment of the system must be a top priority to ensureefficient functioning of the system and enhance thesafety to the end user.

Refer to the following guidelines, illustrations andinstructions for proper use of the Forward-FacingWheelchair and Occupant Belt/Track System.

Wheelchair Passenger Securement

One adjustable lap belt equipped with one “E” clip(keeper) which installs in the vehicle-mounted “A” trackand one female buckle receptacle is provided to beused in conjunction with the existing vehicle OEMfactory-equipped upper torso shoulder harness, forsecurement of the wheelchair occupant. Refer to theillustrations on page 27.

Lap Belt Positioning and Attachments

Refer to the illustrations on page 27.

A. Position of the lap belt buckle, after adjustment, is tobe located near hip position. The belt is to be worn lowand snugly. Adjustment of the lap belt is to be made atadjuster buckle behind the chair.

B. The lap belt must be used in conjunction with thevehicle factory-equipped upper torso shoulder harness.The latch plate side of belt must be opposite shoulderharness to properly extend shoulder harness acrossoccupant. The lap belt end fitting (keeper) must beattached to vehicle-mounted “A” track as outlined inWheelchair and Occupant Belt/Track Attachment

Forward-Facing Wheelchair and Occupant Belt/Track System Instructions

Op

eration


Keeper(“E” Clip)

AdjustableLap Belt

Note: Passenger sidemid-point position shown.Driver side mid pointsecurement is a mirroredimage. Attachmentprocedures are identical.

Adjustable CamBuckle Belt




Existing Vehicle FactoryOEM Installed Upper

Torso Shoulder Harness

Over-centerBuckle Belt

AdjustableLap Belt




Keeper (“E” Clip)attachment detailsare provided on page28 (Steps 2 and 3).

Existing Vehicle OEMFactory-Equipped UpperTorso Shoulder Harness



Horizontal “A” Trackon Floor


Op

eration

Strap Angle Positioning:The load angle should not beless than 30° or more than 60°from vertical in a plane alongthe fitting width as shown.

1

2

3

4

5

76

Tra

ck C

ente

r L

ine

LoadAngle

3" to 8"


continuedForward-Facing Wheelchair and Occupant Belt/Track System Instructions

1. Position and install the strap’strack fitting three inches to eightinches outside the front wheelwith the keeper away fromwheelchair.

2. To install the track fitting,depress the keeper and insertthe fitting (keeper end first) intothe track as shown.

3. Drop back end of fitting intotrack, and release keeper to lockas shown. Pull on fitting toensure that it is locked in track.To remove, simply reverse theprocedure.

4. Loop the other end of the straparound the front of the wheel-chair frame at a structurallysecure location and attach thesnap hook into the round ring asshown. Be careful to keep thestrap away from sharp edges orcorners.

5. Pull the tensioning strap on thecam buckle until tight. Repeatthe four steps for the other frontstrap, making certain thewheelchair is positioned perpen-dicular to the floor track.

6. Velcro* is provided to attachloose strap ends.

7. To release the tension on thestrap, press the buckle cam asshown.

*Velcro is a registered trademark ofVelcro USA, Inc.

Front Cam Buckle StrapAttachments

Read all warnings posted onpage on page 26!

Op

eration


1. Position and install the strap’strack fitting below and just to theinside of the rear wheel asshown. Pull on fitting to ensurethat it is locked in track. Note:See steps 2 and 3 on theopposite page for further trackfitting (keeper) details.

2. Wrap the other end of the straparound the back of the wheel-chair frame at a structurallysecure location and attach thesnap hook into the round ring.Be careful to keep the strapaway from sharp edges orcorners.

3. Pull the tensioning strap untiltight. While maintaining tension,lift handle, close and lockhandle. Pull on buckle handle toensure that it is locked.

4. To release over-center buckle,simply pull down tensioning straptowards floor as shown.

Rear Over-Center StrapAttachments

Read all warnings posted on page 26!

Install, remove andoperate ChryslerEasy-Out™ seats asdetailed in Chryslerowner's manual.Failure to do so mayresult in seriousbodily injury and/orproperty damage.

WARNINGThe 3-Passenger Rear Bench Seat (standardEntervan feature) is equipped with Chrysler Easy-Out Rollers™. Refer to your Chrysler owner’smanual for removal and installation instructions forthis seat.

Chrysler Easy-Out Roller™ Rear Bench Seat

Op

eration


Seat attachmentsmust be fully latchedin floor supportsbefore occupyingseats or operatingvehicle. Failure todo so will result inserious bodily injury.

Front seat removal andinstallation procedures areidentical for driver and passengerseat (driver seat photos shown).

Seat Securement Devices:The quick-release front seats areequipped with mechanical seatbase attachments that attach torecessed floor strikers (supports).Two release handles are locatedat the rear of the seat base.Squeezing the handles androtating the handles downward

disengages the attachments anddeploys the wheels. Squeezingthe handles and rotating thehandles upward engages theattachments.

A lock indicator button pops upwhen the seat is unlocked. Theindicator button returns into thehandle when the attachmentmechanism is in the fully-en-gaged position (seat base attach-ments are fully-engaged with floorstrikers) and in the fully-disen-gaged position (seat base attach-ments are fully-disengaged fromfloor strikers and wheels aredeployed).


1. Disconnect the electrical har-ness sockets (carefully pullsockets apart).

2. Squeeze the release handleslocated at the rear of the seatbases and rotate downward.Rotate the handles down fullyuntil the handles reach thelocked (horizontal) position andthe indicator buttons return intothe handles (photos B-D).

Note: A lock indicator buttonpops up when the seat isunlocked (mid-point of handlerotation). The indicator buttonsreturn into the handles when thehandles are rotated fully down(seat base attachments are fully-disengaged from floor strikersand wheels are deployed).

A B

C D

Fully-Engaged Seat Attachments

Lock Indicator Button UP(Mid-Point of Handle Rotation).

Fully-Disengaged Seat Attach-ments (Wheels Deployed)

Front Seat Removal

DIS

ENG

AGE

DIS

ENG

AGE

DIS

ENG

AGE

WARNING

Wheels Recessed Floor Supports

Release Handles

Driver's Seat Electrical Harness

Driver's Seat Base Foot Rest

Op

eration

Disconnect sockets.


F

Fully-Disengaged Seat Attach-ments (Wheels Deployed)

Front Seat Removal continued

3. Tip seat slightly backwardsand roll seat base out ofvehicle.

1. Roll seat base into position(aligning the seat baseattachments with the re-cessed floor strikers).

2. Squeeze the release handleslocated at the rear of theseat bases and rotateupward to latch the seatbase attachments with therecessed floor strikers(receptacles). Rotate thehandles up and fully forwarduntil the handles reach thelocked position and theindicator buttons return intothe handles. See photos F,G and H.

Note: Be certain all seatbase attachments are fullylatched. Read warning onopposite page!

3. Connect (plug) the electricalharness sockets.

Front Seat Installation

H

Fully-Engaged Seat Attachments

ENG

AGE

ENG

AGE

Connect sockets.

G

Lock Indicator Button UP(Mid-Point of Handle Rotation).

ENG

AGE

Op

eration

Do not contact theramp when recliningor moving a passen-ger seat rearward.Doing so may resultin property damage.

CAUTION

Spare Tire and Jack Location: Due to the modifi-cations* made to the Chrysler OEM (factory) chassisduring the Entervan conversion process, the Enter-van spare tire and jack are relocated. The spare tireis mounted to the spare tire mount and storagecabinet located inside the rear of the Entervan, notin the location outlined in the Chrysler-suppliedowner’s manual. The jack and jack handle arestored in the spare tire mount and storage cabinet.

Jacking and tire changing procedures have not beenaffected by the conversion. Detailed tire changinginstructions are provided in the Chrysler-suppliedowner’s manual. Refer to the Chrysler-suppliedmanual for tire changing instructions and safetyprecautions, as well as instructions regardingother roadside emergencies.

Altered Vehicle decal #21422 (stapled below) issupplied to notify anyone raising or changing a tireon an Entervan that the spare tire and jack havebeen relocated. Affix decal #21422 to the appropri-ate page in the Chrysler-supplied owner’s manual

Tire Cover Spare Tire Mount andStorage Cabinet

where the Tire Changing Instructions begin. In theevent that someone attempting to raise the vehicledoes not refer to this manual, Altered Vehicle decal#21422 will direct the person to the spare tire andjack storage location.

Spare Tire Mount and Storage Cabinet

Storage Cabinet Handle

Wheelchair andOccupant Belts

The storage cabinet providesstorage for the wheelchair andoccupant restraint belts. Thecabinet can also be used forstorage of roadside emergencyequipment.

Lift and rotate the handle counter-clockwise to open the cabinet.Rotate the handle clockwise andpush in to latch the handle.

* This vehicle was altered by TheBraun Corporation and as alteredit conforms to all Federal MotorVehicle Safety Standards affectedby the alteration in effect at thedate of manufacture.

Decal #21422

Tire Changing

Op

eration

Tire Changing

Jack Location and Access

1. Remove spare tire as detailed at left.

2. Loosen and remove the jack storage threadedretainer stud (turn counterclockwise). Removethe jack and jack handle.

Spare Tire Access

1. Remove the tire cover.

2. Loosen and remove the retaining nut (turncounterclockwise). Remove the spare tire.

Tire Changing Instructions

1. Press the dash-mounted redKNEEL switch tothe NO (down)position. If the rearof the vehicle is inthe kneeled posi-tion, the rear of thevehicle will raiseautomatically.

Note: If you haveexperienced poweror equipment failureand the vehicle is inthe kneeled posi-tion, refer to theKneel Actuator

Follow all jackingand tire changinginstructions andsafety precautionsin the Chrysler-supplied owner'smanual when chang-ing a flat tire orraising the vehicle.Failure to do so mayresult in seriousbodily injury and/orproperty damage.

WARNING

Manual Release Instructions on pages 23 and 24of this manual to raise the vehicle. Kneel Actua-tor Manual Release Instructions decal #52215 isposted on the driver side interior wall panel rearof the sliding door above the red-handled manualrelease lever assembly. This decal providesinstructions for overriding the kneel system.

2. Refer to the Chrysler factory-supplied manualfor tire changing instructions.

3. Store and Secure Jack and Tire: Replace thejack and jack handle in the spare tire mount andstorage cabinet and resecure. Secure the flat tireto the spare tire mount and storage cabinet.

Compact Spare Tire: The compact spare tireand wheel assembly (if so equipped), is foremergency use only (not for continuous use).The compact tire should only be used for theminimum length of time (mileage) required to getto a tire service center. Have the proper (original- full size) tire repaired or replaced immediately.Repair or replace the spare tire if worn or dam-aged.

Op

eration

Retaining Nut Jack Storage Threaded Retainer Stud

Maintenance andlubrication proce-dures should beperformed as speci-fied by authorizedservice personnel.Failure to do so mayresult in seriousbodily injury and/orproperty damage.

WARNING

Maintenance and Lubrication Schedule

Inboard (floor) ramp hinge

Outboard ramp extension hinge

Ramp fold pick-up bearing

Ramp extension cable

Wheelchair and occupant restraint belts(❖visually inspect before every use)

Inspect removable front seat bases for properengagement of latching mechanisms

Ramp fold arm bearing slot

Ramp rotation (Passive Access) top and bottompivot points

Passive Access ramp latch

Passive Access ramp latch cable. See CableAdjustment in General Inspection section ifrelease knob does not seat properly in the knobretainer bracket (knob contacts bracket prevent-ing positive latching).

Clean and lubricate with * Light Oil

Clean and lubricate with * Light Oil

Lubricate with * Light Oil

Inspect for proper alignment, securement ordefects such as cuts, fractures, etc. Resecure,replace or otherwise correct as needed

Inspect for any defects such as cuts, fraying orany malfunction of belt, buckle or securementhardware. Replace immediately if defective.

Replace or correct as needed

Lubricate with * Light Grease

Lubricate with * Light Oil

Inspect for proper operation, wear or damage.Lubricate with * Light Oil

Inspect for proper operation, wear or damage.Resecure, replace or otherwise correct asneeded.

Perform all procedures listed in previous section also

4 Weeksor 100Cycles❖

continued

1 Yearor

1250Cycles

Normal vehicle maintenance must beperformed as outlined in the Chrysler-supplied owner’s manual. Thismaintenance is not the responsibilityof The Braun Corporation. Refer tothe Warranty section of this manualfor details regarding The BraunCorporation Entervan Warranty.

Have an authorized service repairmanperform the following Entervanmaintenance and lubrication proce-dures at the scheduled intervalsaccording to the number of cycles orelapsed time, whichever comes first.Discontinue Entervan use immedi-ately if maintenance and lubricationprocedures are not or cannot beproperly performed, or if there is anysign of improper operation, damage,wear or any abnormal condition.

Contact your dealer or call The BraunCorporation at 1-800-THE LIFT. Oneof our national service representativeswill direct you to an authorized servicerepairman who will inspect yourEntervan.

Proper maintenance is necessary toensure safe, troublefree operation.Apply lubricants as outlined in thechart below. Note: Severe conditions(weather, environment, heavy usage,etc.) may require more frequentmaintenance. When replacing lubedcomponents, be sure to lubricateduring installation procedures.

* Lubricants specified within theschedule are available from The BraunCorporation. Part numbers of theselubricants are provided on page 36.

Main

tenan

ce

Correct or adjust as needed

Replace if needed

Tighten, lubricate, adjust microswitches,replace defective parts or otherwise correct asneeded

Inspect for obstructions and clean

Realign, tighten, lubricate, replace defectiveparts or otherwise correct as needed.

Cable Adjustment: Loosen cable securementAllen screws at knob and insert cable furtherand resecure. Remove knob and shorten cable(1/8" intervals) if needed only.

Resecure, adjust microswitches, replacedefective parts or otherwise correct as needed.Note: See Ramp Motor Assembly explodedview on page 48.

Replace defective parts or otherwise correct asneeded

Realign, resecure, adjust, lubricate, replacedefective parts or otherwise correct as needed.Note: See Kneel Actuator Assembly explodedview on page 50 also.


General Inspection

Inspect ramp fold arm for proper alignment withramp pick-up bearing

Inspect ramp fold arm bearing slot for excessivewear or damage

Inspect ramp for proper operation and positivesecurement

Lower power slide door track

Passive Access system - inspect:

• Latch for proper operation (apply * Light Oil)• Latch mounting hardware for positive

securement (loose or missing mountinghardware)

• Release cable for positive securement,alignment, wear, or other damage

• Release knob retainer bracket for positivesecurement, deformation, or other damage

• Does release knob seat properly in the knobretainer bracket? See Cable Adjustment ifknob contacts bracket preventing positivelatching.

• Passive Access latch pin (bolt assembly) forpositive securement, wear, misalignment, orother damage

• Missing or damaged ramp retaining hairpincotter and/or floor rotation flat washer

• Top and/or bottom ramp pivot points (axlesand/or bearing surfaces) for deformation,wear or other damage (apply * Light Oil)

Remove ramp motor cover and inspect:

• Motor mounting bolts for securement (looseor missing)

• Ramp fold arm securement (key)• Microswitches securement and adjustment• Microswitch wires and terminals for secure-

ment or damage

Inspect ramp, ramp fold arm and hinge assem-blies for broken welds, stress fractures, etc.

Inspect Kneel actuator assembly for:

• Actuator mounting bolts securement (looseor missing)

• Actuator shaft/chain bearing slots forexcessive wear or damage

• Actuator shaft/chain bearing slots forlubrication (* Light Grease)

(continued)

1 Yearor

1250Cycles

continued

continued

Main

tenan

ce


General Inspection * continued

Realign, resecure, adjust, lubricate, replacedefective parts or otherwise correct as needed.Note: See Kneel Actuator Assembly explodedview on page 50 also.

Resecure, repair or replace

Resecure, repair or replace

Replace if worn, missing or illegible. SeeDecals on pages 52-57.

15807

Specified (recommended) Available BraunLubricant Type Lubricant Amount Part No.

Light Penetrating Oil LPS2, General Purpose 11 oz.(30 weight or equivalent) Penetrating Oil Aerosol Can

Light Grease Lubriplate 14 oz.(Multipurpose) Can

Refer to the Maintenance/Lubrication Schedule for recommended applications per number of cycles or elapsed time.

* Light Oil

* Light Grease 15805

continued

Inspect Kneel actuator assembly for:

(continued)

• Actuator shaft/chain bearing lock collars forsecurement

• Inspect chain for misalignment, wear ordamage (apply * Light Grease)

• Inspect chain cotter pins for securement• Inspect chain UHMW idler for securement,

wear, damage or misalignment• Inspect electrical harnesses for positive

connections, proper routing, wear or otherdamage

• Inspect proximity switch mounting screws• Inspect polyethylene hose for positive

connection, routing, kinks, holes, wear orother damage

• Release cable mounting bracket mountingbolts securement (loose or missing)

• Release cable securement (turnbuckleconnection at motor, threaded mountingstud at mounting bracket and all jam nuts)

• Release cable alignment, routing, kinks,wear, or other damage

Inspect power cable

Inspect ground cable

Decals

1 Yearor

1250Cycles

Main

tenan

ce

Troubleshooting Diagnosis Chart

If a problem occurs with your Entervan, discontinue operation imme-diately. Contact your dealer or call The Braun Corporation at 1-800-THE LIFT. One of our national service representatives will direct you toan authorized service repairman who will inspect your Entervan.

The cause of the problem can be determined by locating the functionand related symptom in the Troubleshooting Diagnosis Chart. Thespecific cause and remedy can then be determined by process ofelimination. An Electrical Schematic and a Wiring Diagram are pro-vided for troubleshooting diagnosis. A Repair Parts section (Section 4)with exploded views and corresponding parts lists is provided. Correctthe problem if possible. If the problem continues, contact The BraunCorporation.

WARNING

Troubleshooting andrepair proceduresmust be performedas specified byauthorized servicepersonnel only.Failure to do so mayresult in seriousbodily injury and/orproperty damage.

FUNCTION SYMPTOM POSSIBLE CAUSE REMEDY

1.00NO

OPERATION

1.10No Power

To EntervanSystems

(Circuit Problem)

1.20Power toEntervanSystemsBut No

Operation

1.11 Poor ground connection1.12 Battery terminals dirty1.13 Battery defective1.14 Battery discharged1.15 12 volt source

1.16 Circuit breaker faulty

1.21 Transmission not in Park1.22 MANUAL/AUTO switch(s) not in

AUTO position1.23 Park Interlock microswitch

harness disconnected ordefective

1.24 Park Interlock microswitch out ofadjustment or defective

1.25 Loose connection1.26 Broken wire1.27 Wire terminal1.28 Switch defective1.29 Relay(s) defective

2.11 See 1.002.12 Park Interlock harness discon-

nected or defective2.13 KNEEL switch not in YES position2.14 Kneel Actuator MANUAL/AUTO

switch not in AUTO position2.15 Kneel actuator brake manually

released or other Kneel ActuatorManual Release problem.

2.16 Open control not activatedcontinuously for two seconds ormore (delay feature)

2.17 Kneel time delay defective2.18 Faulty fuse2.19 Actuator harness disconnected,

damaged or otherwise defective2.20 Actuator defective2.21 Roller chain disconnected,

damaged or otherwise defective

Clean and tightenClean and tightenReplaceCharge batteryCheck for loose terminals or brokenwire or cableRepair or replace

Engage transmission in ParkPress switch to AUTO position

Connect, repair or replace

Adjust or replace

Clean and tightenRepair or replaceCrimp tightly to wireReplaceReplace


Press Kneel switch to YES positionPress switch to AUTO position

Correct or repair as needed

Activate OPEN control for two secondsor longer (through delay)

ReplaceReplace fuseConnect, repair or replace

ReplaceConnect, repair or replace

continued continued

2.00KNEELSYSTEM(LOWER)

2.10No

LOWEROperation

Tro

ub

lesho

otin

g



continued continued

continued continued

Tro

ub

lesho

otin

g

Correct

Correct, replace and/or lubricate asneeded


Adjust or replace

Replace fuseConnect, repair or replace

Replace motor

Engage door operator. See Door andRamp Manual Operating InstructionsAlign, replace or otherwise correct asneeded

Remove obstruction

Realign, tighten, lubricate, replacedefective parts or otherwise correct asneededRealign, tighten, lubricate, replacedefective parts or otherwise correct asneeded

Activate OPEN control until door stops(opens fully)

Adjust microswitch so door opens fullyor replace

2.31 Mechanical binding2.32 Misalignment or damage to kneel

system components. InspectKneel actuator assembly for:• Actuator mounting boltssecurement (loose or missing)

• Actuator shaft/chain bearingslots for excessive wear ordamage

• Actuator shaft/chain bearingslots for lubrication (* LightGrease)

• Inspect chain for wear, misalign-ment, damage or lack oflubrication (* Light Grease)

• Inspect chain aluminum idler forsecurement, wear, damage ormisalignment

• Inspect polyethylene hose forpositive connection, properrouting, kinks, holes, wear orother damage

3.11 See 1.003.12 Door harness disconnected or

defective3.13 Door Opened microswitch out of

adjustment or defective3.14 Faulty fuse3.15 Door operator motor harness

disconnected or defective3.16 Door operator motor defective

3.21 Door operator manual releasehandle up (motor disengaged)

3.22 Misaligned or otherwise damagedmotor gear, gear adapter or doorgear rack

3.31 Obstruction in lower slide doortrack

3.32 Mechanical binding

3.33 Worn, damaged, misaligned,loose or missing door operatorcomponents such as springs,motor gear, gear adapter, gearrack and associated mountinghardware

3.41 OPEN control not activatedthroughout entire door openingfunction (until door stops)

3.42 Door Opened microswitch out ofadjustment or defective

3.20Motor RunsBut DoorDoes Not

Move

3.10NO

OPENOPERATION(Motor Does

Not Run)

3.30FaultyOpen

Operation

3.40Door DoesNot Open

Fully

2.00KNEELSYSTEM(LOWER)

2.30FaultyKneel

(Lower)Operation

3.00POWERDOOR(OPEN)


continued continued



Adjust or replace

ReplaceContinue to activate OPEN control fortwo seconds or longer after door isopen (through delay)


Adjust or replace

Replace motor

Adjust or replace Door OpenedMicroswitchEngage latch fully or repair PassiveAccess latch system


Adjust or replace

Realign, tighten, replace defective partsor otherwise correct as needed

Tighten, replace or otherwise correct asneededCheck and correctLubricate — See Maintenance andLubrication Schedule

Replace, attach or otherwise correct


Adjust or replace

Activate CLOSE control until rampstops (folds fully)


4.11 See 1.004.12 Faulty fuse4.13 Door harness disconnected or

defective4.14 Door Opened microswitch out of

adjustment or defective4.15 Door time delay defective4.16 Open control not activated

continuously for two seconds ormore after door is fully open(delay feature)

4.17 Ramp motor harness discon-nected or defective

4.18 Ramp Unfolded microswitch out ofadjustment or defective

4.19 Ramp motor defective

4.21 Door not fully open

4.22 Passive Access latch not fullyengaged (ramp not latched)

4.31 Ramp Unfolded microswitchharness disconnected ordefective

4.32 Ramp Unfolded microswitch out ofadjustment or defective

4.33 Misalignment or damage to:• Ramp fold bearing• Ramp fold arm• Ramp fold arm bearing slot• Ramp hinge

4.34 Loose, damaged or missing foldarm securement key

4.35 Mechanical binding4.36 Lack of lubrication

4.41 Ramp extension cable broken,detached, misaligned or other-wise defective

5.11 See 1.005.12 Faulty fuse5.13 Ramp harness disconnected or

defective5.14 Ramp Folded microswitch out of

adjustment or defective5.15 See 4.13, 4.14, 4.18 and 4.19

5.21 CLOSE control not activatedthroughout entire ramp foldingfunction (until ramp stops)

5.22 Ramp Folded microswitchharness disconnected ordefective

continued continued

5.20FaultyFold

Operation

5.10NO

FOLDOperation

4.40Faulty RampExtension

Unfold

4.30FaultyUnfold

Operation

4.10NO

UNFOLDOperation

4.00RAMP

UNFOLD

5.00RAMPFOLD

4.20Ramp

ContactsDoor

Tro

ub

lesho

otin

g



continued continued

6.30Faulty

Operation

6.40Door WillNot Close

Fully

Adjust or replace


Adjust or replace

Remove obstructionActivate CLOSE control until door stops(closes fully)

Adjust microswitch so door closes fullyor replace

Clean and lubricate with * Light Oil,remove obstruction or otherwise correct


Adjust or replace

Crimp tightlyRepairClean and tightenReplace fuseConnect securely

Replace if under 8.8 voltsReplace transmitterMatch transmitter code to receiver.Procedure: Match transmitter DIPswitches #1-#9 to receiver DIP switchcode. Transmitter DIP switch #10 mustbe opposite receiver DIP switch #10.Note: Reverse #10 switches to reversetransmitter push button functions.

5.00RAMP FOLD

5.23 Ramp Folded microswitch out ofadjustment or defective

5.24 See 4.33, 4.34, 4.35 and 4.36

6.11 See 1.00 and 3.106.12 Ramp harness disconnected or

defective6.13 Ramp Folded microswitch out of

adjustment or defective

6.21 See 3.20

6.31 See 3.30

6.41 Obstruction in door opening6.42 CLOSE control not activated

throughout entire door closingfunction (until door stops)

6.43 Door Closed microswitch out ofadjustment or defective

6.51 Outboard ramp extension hingenot properly lubricated, obstructedor otherwise damaged

6.52 Ramp Folded microswitchharness defective

6.53 Ramp Folded microswitch out ofadjustment or defective

7.11 See 1.00, 2.12, 2.13, 2.18, 2.19,2.20 and Section 2.30

7.21 See Section 2.30

8.11 See 1.00

8.21 Wire terminals8.22 Broken wire8.23 Poor ground connection8.24 Faulty fuse8.25 Wiring harness unplugged

8.31 9 Volt battery defective8.32 Transmitter switch defective8.33 Transmitter replaced without

proper coding8.34 Additional transmitter added to

system without proper coding

8.30No Signal

(Code) BeingTransmitted

8.20Power toEntervan

Systems ButNo Power to

Receiver

7.10NO RAISEOperation

6.50Door ContactsRamp When

Closing

6.10NO

CLOSEOperation

7.00KNEELSYSTEM(RAISE)

8.10No Operation

8.00REMOTE

CONTROL

6.00POWERDOOR

(CLOSE)

5.20Faulty FoldOperation

continued continued

7.20Faulty

Operation

6.20Motor Runs - Door

Does Not Move

Tro

ub

lesho

otin

g



Check voltage. Replace if defective.Replace if under 8.8 voltsCorrect or replaceCorrectTighten

Move transmitter within range

Replace receiver

Replace, connect or repair

Press switch to MANUAL position

Insert detent pin in release handle(fully-rearward position)Align, reroute, remove kinks, repair orreplace

Correct or replace

Correct or replace

Lubricate — * Apply Light Grease

Tighten, align or replace

Tighten or replace

Hold key in OPEN position for approxi-mately two seconds to start operationConnect, repair or replace

Adjust or replace


Replace Time Delay

Realign, replace defective parts orotherwise correct as needed

8.41 Vehicle battery8.42 9 Volt battery low8.43 Antenna deformed or damaged8.44 Antenna contacting metal8.45 Antenna loose in receiver

receptacle8.46 Out of 35 foot maximum range

8.51 See 8.208.52 Defective receiver

9.11 Release cable missing, discon-nected (turnbuckle connection atmotor, threaded mounting stud atmounting bracket, release leverconnection), or otherwisedefective

9.12 Power still applied to actuator(Kneel Actuator MANUAL/AUTOswitch not in MANUAL position)

9.21 Detent pin not inserted in releasehandle (fully-rearward position)

9.22 Release cable out of adjustment,out of alignment, routing obstruc-tion, kinked, worn or otherwisedamaged

9.23 Manual release lever bent,deformed or misaligned

9.24 Wear or damage to actuator shaft/chain bearing slots

9.25 Lack of lubrication in actuatorshaft/chain bearing slots

9.26 Loose, misaligned or damagedactuator shaft/chain bearing lockcollars

9.27 Loose or missing release cablemounting bracket mounting bolts

10.11 See 1.0010.12 Key Entry key not held in OPEN

position long enough (delay)10.13 Key Entry Open microswitch


10.14 Key Entry Open microswitch outof adjustment or defective

10.15 Faulty fuse10.16 Time Delay harness discon-

nected or defective10.17 Time Delay defective

10.21 Misalignment, wear or damageto slide lever, bushing spacers ormounting bracket

10.22 See 10.14, 10.16 and 10.17

continued continued

8.00REMOTE

CONTROL

continuedcontinued

8.40Poor

Reception(Pulsating)

9.10No

Operation

8.50Signal Received

But No Operation

10.20Faulty OPENOperation

9.00KNEEL

ACTUATORMANUALRELEASE

10.00KEY ENTRY

9.20Faulty

Operation

10.10No

OPENOperation

Tro

ub

lesho

otin

g


10.31 See 1.0010.32 Key Entry Close microswitch


10.33 Key Entry Close microswitch outof adjustment or defective

10.41 See 10.21 and 10.33


Adjust or replace

continued continued


10.00KEY ENTRY

10.40Faulty CLOSE

Operation

10.30No

CLOSEOperation

11.10No

ReleaseOperation

11.11 Release cable broken, discon-nected or otherwise defective

11.12 Faulty Passive Access latch (willnot disengage)

11.21 Loose, worn or otherwisedamaged Passive Access latch

11.22 Missing, loose, worn, bent,misaligned or otherwisedamaged Passive Access latchpin (bolt assembly)

11.23 Mechanical binding11.24 Lack of lubrication to latch

11.31 Missing PVC washer at bottompivot point (axle)

11.32 Misalignment, deformation, wearor other damage to top and/orbottom pivot points (axles and/orbearing surfaces)

11.33 Misalignment, deformation,looseness, wear or otherdamage to inboard (floor) ramphinge assembly, floor and lowerslide door track assembly ormounting hardware

11.34 Mechanical binding11.35 Lack of lubrication to top and

bottom pivot points

11.41 Faulty Passive Access latch (willnot engage)

11.42 See 11.20

11.51 Release knob does not seatproperly in knob retainer bracketpreventing latch from returningto spring-loaded latch position

11.52 See 11.20, 11.33 and 11.41

Connect or replace cable

Replace latch

Tighten, replace or otherwise correct asneededTighten, replace or otherwise correct asneeded

Correct as neededLubricate with * Light Oil

Replace washer

Correct as needed

Correct as needed

Correct as neededLubricate with * Light Oil

Replace latch

Cable Adjustment: Loosen cablesecurement Allen screws at knob andinsert cable further and resecure.Remove knob and shorten cable (1/8"intervals) if needed only.

11.20Faulty

ReleaseOperation

11.50Faulty

Latching

11.40No LatchingOperation

11.30Faulty

RotationOperation

11.00PassiveAccessSystem

Tro

ub

lesho

otin

g

Notes

Tro

ub

lesho

otin

g

WARNING

Risk of electrical fire!Install and electricallyterminate Auxiliaryelectrical device asspecified by devicemanufacturer.

A fuse block that can accommo-date up to six additional ATO®

type fuses is provided behind thedash below the steering column.This power source is available forinstallation of a dealer-installedpower seat, an electric tie-downor other auxiliary electrical device.The installer is responsible forsupplying the correct gaugewire and fuse for the particulardevice to be attached to the fuseblock (as specified by themanufacturer of the device).

The maximum load must notexceed 25 amperes. Wiringmust be routed and terminatedproperly by the installer. Wires

with female fully-insulated termi-nals can simply be connected toone of six available terminals onthe fuse block. Note: If install-ing an auxiliary electricaldevice that requires more thana 25 ampere power source, analternative power source mustbe provided. Refer to theElectrical Schematic and WiringDiagram contained in thismanual.

Note: A switch and power-supplycable are supplied with eachEntervan® for use when installingan auxiliary electrical device (ifapplicable).

Auxiliary Power Supplyfor Dealer-Installed Power Seat or Tie-Down

Tro

ub

lesho

otin

g

Wiring Diagram

Page 45A Page 46A

1 23

4

1 23

4

W / BK / V

W / BK / V

W /

BK

/ V

W /

BK

/ V

W /

V

#2#1

#3 #4 #5 #6 #7 #852

050A

-03

R 12V R 12V

R 12V

R 12V

R 12V

R 1

2VR

12V

R /

BK

W / BN / BU

BU / BK

W / BK / BU

W / OR / BN

R /

BK

R / BK

W /

OR

/ Y

W /

OR

/ Y

W / OR / Y

W / BK

W / BK

W / BK

W / BK

W / R

W / R

W /

R

W / R / BUW / R / BU

W / BK / GYW / BK / GY

Ground

BAT.

Aux.

(30 Amp.)

5204

6A

R 12V R 12V

R 12V

Ground

W /

BK

/ B

NW

/ B

K /

VB

N

R 12V

W / BK

W /

BKW /

R /

V

W /

R /

OR

W /

BR

/ O

R

OR

/ B

K

OR / BK

#9 #10

R 12V R 12V

R 1

2V

R 12V

Ground

R 12V

W /

BK

52037A

25

25

25

5

5

Kneel Actuator

Front Fuse Block Rear Fuse Block

R 1

2V

R 1

2V

R 1

2VGround

Park InterlockMicroswitch

W #

7

Connects to Vehicle Battery

(+) Positive Post

CircuitBreaker W / BK / BN W / BK / BN

W /

BK

/ B

N

W / BK / V W / BK / V

W #8

W / BK / R

W / BK / R

W / BK / R

W / BK / R

W / BK / R

W / BK / R

R / BK

R / BK

R 12V

R 12V

R 12V

BU

BU

BU

W #7

R 12V

R 12V

BNBN

V

TerminalBlock

2

1

3

4

5

6

7R 1

0 G

A.

R 1

2V

V

WW #7

R 1

2V

R 1

2V

Two-TouchRemote Control

Receiver

W /

R

5203

8A

V

W / BK / VW / V

BN

W / BK / BNW / BN / OR

W / R / V

W / BK / V

Ramp FoldedMicroswitch

R

BK

W / R / OR

OR / BK

RampFold/Unfolded

Gear Motor

Manual / AutoRamp Switch

OR

/ B

KO

R /

BK

Wall-MountedOpen / Close

Switch

52044A-0352044A-03 52044A-03

W

BN

V

V

2

3

1

Connects to Terminal Block #:

W / BK

R 12V

6

5

4

3

2

1

COLORNO.

9-COND WIRE CODE

7

8

9

WHITE / BLACK / GRAY

WHITE / BLACK / BLUE

BLUE / BLACK

WHITE / GREEN

WHITE / RED

WHITE

WHITE / BROWN / BLUE

WHITE / RED / BLUE

NOT USED

46 513 2

79 8

64 531 2

97 8

2 13 2

46 5

79 8

2 31 2

64 5

97 8

2 31 2

64 5

97 8

6

5

4

3

2

1

COLORNO.

9-COND WIRE CODE

7

8

9

WHITE / BLACK / GRAY

WHITE / BLACK / BLUE

BLUE / BLACK

WHITE / GREEN JUMPER

WHITE / RED

WHITE / GREEN JUMPER

WHITE / BROWN / BLUE

WHITE / RED / BLUE

NOT USED

6

5

4

3

2

1

COLORNO.

9-COND WIRE CODE

7

8

9

WHITE / BLACK / BROWN

WHITE / BLACK / VIOLET

WHITE / RED / VIOLET

BROWN

ORANGE / BLACK

WHITE / RED / ORANGE

WHITE / BROWN / ORANGE

NOT USED

NOT USED

6

5

4

3

2

1

COLORNO.

9-COND WIRE CODE

7

8

9

WHITE / BLACK / BROWN

WHITE / BLACK / VIOLET

WHITE / RED / VIOLET

BROWN

ORANGE / BLACK

WHITE / RED / ORANGE

WHITE / BROWN / ORANGE

NOT USED

NOT USED

64 531 2

97 8

2 31 2

64 5

97 8

2 31 2

64 5

97 8

46 513 2

79 8

2 13 2

46 5

79 8

6

5

4

3

2

1

COLORNO.

9-COND WIRE CODE

7

8

9

NOT USED

WHITE

NOT USED

NOT USED

NOT USED

NOT USED

RED

VIOLET

BROWN

46 513 2

79 8

64 531 2

97 8

2 13 2

46 5

79 8

2 31 2

64 5

97 8

2 31 2

64 5

97 8

6

5

4

3

2

1

COLORNO.

9-COND WIRE CODE

7

8

9

NOT USED

WHITE

NOT USED

NOT USED

NOT USED

NOT USED

RED

VIOLET

BROWN

D

C

B

A

NO.

4-COND WIRE CODE -ACTUATOR MOTOR

MF

M F

BLACK

RED

GREEN

WHITE

FEMALE

BLUE / BLACK

WHITE / RED

WHITE / GREEN

WHITE

MALE

F7

F8

F9

F10

F11

F12

F1

F2

F3

F4

F5

F6

P /

J 3

P /

J 2

P /

J 1

P / J 8

P / J 9

P / J 7

C & D

B

A

NO.

4-COND WIRE CODE -PROXIMITY SWITCHES

BLUE

BLACK

BLUE

BLACK

MALE

W / BN / BU

W / BK / GY

W / R / BU

W / BK / BU

FEMALE

C

D

RETRACTED

EXTENDED

A &

B

EXT. RET.

S

C-H

COMNO

NCN.O.

N.C.

COM.

Ramp UnfoldedMicroswitch

S

C-H

COMNO

NCN.O.

N.C.

COM.

S

C-H

COMNO

NCN.O.

N.C.

COM.

Door OpenedMicroswitch

DoorOperator

Motor

RY

P / J 6

V

V

V

BN

W W

BN BN BN

V

V V V

V

BN

R 1

2V

KneelSwitch

W #8

C NCNO

P / J 12

W #8

W #

7

52042A

W

V

R 12V

R 12V

R 12V

R 1

2V

BK

BU

Key Entry OpenMicroswitch

BKClose

Open

W

BUBN

Key Entry CloseMicroswitch

52048A

Outside Key EntryTime Delay

KneelTime Delay

2

1

3


V

GY

GY

V

BN

W

Y

R

5

25

R 10 GA.

Y

W / R

1 23

4

R 1

2V

R 1

2V

5204

6A

5204

3A-0

252

043A

-02

W / R

Y

6511

1A

5195

9A

R 10 GA. 6510

8A

5204

5A

Dash-MountedOpen / Close

Switch

W

BN

V

V

2

3

1


52041A

W

C NCNO

C NCNO

Manual / AutoKneel Switch

Y

Y

Y

V

DoorTime Delay

KNEEL (Y-6)

KNEEL (Y-5)

KNEEL (Y-4)

KNEEL (Y-3)

KNEEL (Y-2)

6

5

4

3

2

FUNCTIONNO.

7

8

9

RAMP (Y-7)

RAMP (Y-8)

DOOR (Y-9)

10 DOOR (Y-10)

Relay BlockIdentification Code

Electrical Schematic

Page 46BPage 45B

30

85

87A

87

86

30

85

87A

87

86

M

W / R

2-TOUCHREMOTE

10 GA. RED

BN

W

V

TERMINALBLOCK

REAR FUSE BLOCK

NOC

NC

25

V

BN

W / BK / V

WW

BN

BNBN

W / BK / R

1

2

4

5

6

7

W / V

OPEN

CLOSE

VV

W #8

M

BATTERY

CHASSIS GROUND

CIRCUIT BREAKER

CONNECTORS

JUNCTION

MOTOR

SWITCH

85 86

RELAY

87

87A30

SOLENOID

SYMBOLDESCRIPTION

SOLENOID OR RELAY

FUSE

THERMAL OVERLOAD PROTECTION

MICROSWITCH

25

5

5

25

30 A.

PARK INTERLOCKSWITCH

WALL-MOUNTEDOPEN / CLOSE

SWITCH

OPEN

CLOSE

NO

C

NC

OUTSIDEKEY ENTRY

OPEN

BN

GY GY

W

V

NO

C

NC

NO

C

NC

30

85

87A

87

86

30

85

87A

87

86

M

DOOR OPENEDMICROSWITCH

DOOROPERATOR

MOTOR

RAMPMOTOR

RAMPMANUAL/AUTO

SWITCH

RAMP UNFOLDEDMICROSWITCH

RAMP FOLDEDMICROSWITCH

30

85

87A

87

86

30

85

87A

87

86

30

85

87A

87

86

NC

W /

BK

/ G

Y

W /

BK

/ G

Y

W /

OR

/ Y

W / BK

W / BK

W / BK

R 12V (F2)

W / BN / BU

W /

BK

/ B

U

BU

BU

W / OR / BN

BN

V

W

ACTUATOREXTENDEDPROXIMITY

SWITCH

BK

BU W / R / BU W / R / BU

NC

BK

BU

ACTUATORRETRACTEDPROXIMITY

SWITCH

W / BN / BUW / BN / BU

R 12V

BN

V

W

W / GN

MKNEEL

ACTUATOR

W / GN

W

R

BU / BK

BU / BKBU / BK

BU / BK

BU / BK

KNEELSWITCH

W / V

W

BNBN

V

R 12V

R

12V R

12

V

OR

/ B

KB

KR

W / R / OR W / R / OR W / R / V

W / BK / V

W / BN / OR

W /

BK

/ B

NW

/ B

K /

BN

BN

BN

BNWV

BN

W

V

BNWV

BN

W

V

W / BK / BN W / BK / BN W / BK / BN

W / BK / V

W / BK / V

W / BK / V

W / BK / V

W / BK / V

W /

BK

/ V

R

12V

BN

V

W

R

12V

R

12V

R

12V

RY

Y

Y

R

12V

R 12V

R 12V

W #

8W

#8

W #7W #7

BU

BU

OR

/ B

K

W

W

BK

R 12V

R 12V (F2)

R 12V (F2)

F1

F2

F3

F4

F5

F6

GN

DRAWING SHOWN WITH:• VEHICLE IN PARK• KNEEL SWITCH IN YES• KNEEL MANUAL/AUTO SWITCH IN AUTO• RAMP MANUAL/AUTO SWITCH IN AUTO• RAMP STOWED• DOOR CLOSED• VEHICLE RAISED

BRAKE

BN

RAMP REMOTE

DOOR

KNEEL

KNEEL

KNEEL SOURCE R 12V

KNEEL SOURCE R 12V

R

12V

R

12V

BU

FRONT FUSE BLOCK

10 GA. RED

W / BK / GY

F7

F8

F9

F11

F12

W / R

W / RW / R

P8-D

P8-C

P8-A

P8-B

W / R

P1-4

P1-2

P1-1

P1-3

P1-7 P9-D

P9-CP1-6

P1-8P9-B

P9-A

P1-

5P3-7

P3-9

P3-8

P3-5

P6

P6-

TA

B

P2-6

P2-5

P2-3

W /

R /

VW

/ B

N /

OR

P2-7

P2-4P2-1

P7-

AP

7-B

OR

/ B

KP

2-2

Y-4

Y-5

Y-6

Y-7

Y-8

Y-9

Y-10

CLOSEC C

NC NO NC NO

BKBK

TIMEDELAY

V

V

V

V

V

5TIME DELAY

R

12V

R 12VR 12V

R

12V

R 12V

R 12V

W #8

P12

-2

CLOSE

DASH-MOUNTEDOPEN / CLOSE

SWITCH

OPEN

W

W

W

W #

7

W #7

BN

V

V V

V

BN

3

W / R

1

2

4

3

25F10

30

85

87A

87

86

W /

BK

/ R

W / BK / R W / BK / R

W / BK / R

W / BK / R

W / BK / R

W

W

R 12V (F3)Y-2

30

85

87A

87

86

R /

BK

BN

BN

BNBN

BN

BN

BN

R / BK

R / BK

R / BK

R / BK

R / BKR / BK

R /

BK

R 12V (F2)Y-3

TIMEDELAY

VVV

VV

1

2

4

3

R 12V (F3)

TIMEDELAY

DOORV

1

2

4

3

1/2MANUAL/AUTOKNEEL SWITCH

1/2MANUAL/AUTOKNEEL SWITCH

Y-1KNEEL

KEYENTRY

Unfold

for

Wiri

ng D

iagr

am

Repair Parts

1

2

3

4 5

6

6

7

8

9

9

9

10

17

18

19

121314

10

10

11

15

16

21

20

2223

222324

24

Power Door Operator Assembly

Item Qty. Description Part No.

13 1 Screw, #10-32 x 1/2", Button Head -SK 17193

14 1 Nut, #10-32, with Lockwasher 18349

15 1 Pin, 1/4" Diameter x 1" 16314

16 2 Pop Rivet, SD64BS 11513

17 1 Microswitch 51816

18 2 Nut, #4-40, with Lockwasher 19537

19 2 Screw, #4-40 x 5/8", Round Head 14810

20 1 Spring, 1/4" x 1", Extension with Hooks 10774

21 2 Bolt, 5/16"-18 x 1", Carriage 15572

22 2 Washer, 5/16", Flat 10063

23 2 Washer,5/16", Lock 10068

24 2 Nut, 5/16"-18, Hex 10058


1 1 Weldment, Door Operator Bracket 51176A96

2 1 Weldment, Gear Rack Tube 51252A96

3 1 Weldment, Motor Mounting Pivot Plate 51178A

4 1 Motor 19069

5 1 Gear Adapter 19071

6 3 Spacer, Motor 19130

7 3 Screw, #12-24 x 2", HH Type 23 19095

8 1 Gear Rack, Door Operator 52510

9 3 Washer, 1/4", Flat 10062

10 3 Nut, 1/4"-20, Hex Lock 10775

11 1 Manual Release Handle 52509

12 1 Plate, Microswitch Mounting 52511

Rep

air Parts

1

2

3

4

667

3

3

4

4

5

5

8

8

9

11

11

11

11

16

11

10

12

1314

12

15

Repair Parts

Power Ramp Motor Assembly Parts List

Ramp Assembly Parts List


1 1 Ramp Extension 51508-292 1 Ramp 51509-293 44 Screw, #10-32 x 1/2", Fl. Hd. - HX SKT 171924 44 Nut, #10-32 with Lockwasher, Zinc Pl. 183495 1 Hinge, 2" x 1/4" x 28", Stainless 18619R028

6 1 Weldment, Ramp Hinge - 29" 51542A-297 3 Stop, Mini Ramp, 30" (7 Gauge) 191298 1 Stop, Mini Ramp, 30" 186029 1 Link Extension Weldment 19021A

10 6 Screw, 1/4"-20 x 1/2", Fl. Soc. Cap Hd. 1886011 2 Bolt, 1/4"-20 x 3/4", Allen, Flat Head 1870812 1 Screw, 1/4"-20 x 3/4", Allen, Button Hd. 2014313 1 Washer, 1/4", Lock 1006714 1 Washer, 1/4", Flat 1006215 1 Pin, Ramp Support 5181516 1 Latch Bolt, Ramp Support 51541-9617 1 Screw, #8-18 x 3/4", Wafer Head 1414918 1 Cable Clip, 7/16", Plastic 1577719 2 Rubber Bumper 1095020 1 Bolt, 1/4"-20 x 1-1/4", Carriage 1475621* 1 Hose, 1/4" x 5/8", Fuel 51211R (5/8")

22 2 Nut, 1/4"-20, Hex 1005723 1 Cable Assembly 52513A24 1 Latch, with Cable 51652A25* 1 Hose, 1/4" x 2', Polyethylene 11144R (24")

26 1 Bracket, Cable Release, 29" Ramp 5154727 6 Screw, #8-18 x 1/2", Self-Tap,Phillips 1853328 1 Pin, Passive Release 1865029 2 Screw, #8-32 x 1/8", Set 1155730 1 Plate, Threshold, 29", Stainless Steel 5181431 1 Nut, 1/4"-20, Nylock 14614


1 1 Drive Arm Weldment 51514A-302 1 Housing Weldment 51515A-303 3 Bolt, 1/4"-20 x 3/4", Hex 109704 3 Washer, 1/4", Flat 100625 2 Microswitch, SPDT Cherry 142186 3 Screw, #4-40 x 1" Round Head 114847 1 Screw, #4-40 x 3/4" Round Head 114838 4 Nut, #4-40 with Lockwasher, Zinc Pl. 195379 1 Cover, Gear Motor/Housing 5151810 1 Motor, Ramp Assembly 51654A11 5 Screw, #8-18 x 1/2", PH/PHL SD SS 1853312 2 Bearing, Platform Fold 1885113 1 Pulley, Ramp Cable, Arm Drive 5153914 1 Bolt, 1/4"-20 x 3/4", Allen, Flat Head 1870815 1 Key, 3/16" x 3/16" x 1-1/4" 1100216 1 Washer, 3/8" x 1" x 1/16", PVC 19039

Power Ramp Motor Assembly

Note: Parts Listingbelow (in grey box).

* Raw material items ordered and priced per length (order specified length)

Rep

air Parts

Repair Parts

Ramp Assembly

1 3

3

19 4

23

3

3

204

21

22

6

5

7

1615

14

1213

87

4

7

10

10

10

11

31

27

27

27

27

30

28

26

2729

19

4

25

11

24

23

9

11

1718

Note: Parts Listing on oppositepage (in white box).

Rep

air Parts

Repair Parts

Kneel Actuator Assembly

1

2

4

6

23

8

8

8

9

9

9

9

11

10

11

1213

21

3

5

7

14

15

1617

18

823

98

239

8

2310

23

23

7

22

8

8

8

8

8

9

9

9

22

24

23

23

23

17

18

* Raw material items ordered and priced per length (order specified length)


1 1 Weldment, Actuator Mtg. Plate, Front 52030A

2 1 Weldment, Actuator Mtg. Plate, Rear 52031A

3 1 Weldment, Chain Adapter 52064A

4 1 Pin, Actuator Guide 65521

5 1 Chain Bolt, 4 x 4 x 7/16"-14 x 2.25 22868

6 1 Stud, Chain Attachment, 4 x 4 - .5P 52062

7 1 Tubing, 3/4" O.D. x .51" I.D. x 1.06" 13135R001

8 11 Washer, 3/8" Flat 10064

9 9 Bolt, 3/8"-16 x 1", Hex 10025

10 2 Bolt, 1/2"-13 x 3", Hex 10041

11 2 Washer, 1/2" Lock 10070

12 1 Pulley w/Bushing, Chain, Kneel, 4 x 4 51963A


13 1 Actuator, Kneel 51410

14 1 Nut, 7/16"-14, Hex Nylock 12895

15 1 Nut, 7/16"-14, Hex Jam 14414

16* 1 Chain, Leaf, 4 x 4 - .5 Pitch 21708R (11.5")

17 2 Pin, Cottered, 4 x 4 Leaf Chain 21759

18 2 Pin, Cotter, 1/16" x 3/4" 13713

19 1 Hose, 3/8" x 4", Polyethylene - not shown 15694R004

20* 1 Hose, 1/4" x 36", Polyethylene - not shown 11144R (36")

21 1 Rod, Threaded, #10-24 x 1" 19517R001

22 3 Washer, 1/2", Flat 10065

23 9 Washer, 3/8", Lock 10069

24 1 Mount, Chain Bolt 51714

Note: Kneel ActuatorManual Release LeverAssembly explodedview on opposite page.

Rep

air Parts

Repair Parts


1 1 Faceplate Weldment, Act. Man. Rel. 52013A2 1 Handle, Manual Release 513663 2 Washer, Nylon 126904 1 Nut, 1/4"-20, Nylock 146145 1 Bolt, 1/4"-20 x 3/4", Hex 109706 1 Cap, Vinyl, Red 182387 1 Pin, Detent 219188 1 Cable Assembly 520039 1 Spring 2192810 4 Screw, #8-18 x 3/4", PH/PHL SD SS 1814411 1 Screw, #8-18 x 1/2", PH/PHL SD SS 1853312 1 Switch, Manual- Auto 65215

Kneel Actuator ManualRelease Lever Assembly

1

11

MANUAL

AUTO

2

34

5

6

7

8

9

10

10

10

12

10

1

2

3

6

6

7

7

4

4

5

58

8

Passenger Door Outside Key Entry Assembly


1 1 Plate, Microswitch Mount, Key Entry 525012 1 Slide Lever, Key Entry 525023 2 Bushing Spacer 525034 2 Microswitch, SPDT Cherry, WTRPRF 179525 4 Screw, #2-56 x 1/2" Round Head 179616 4 Nut, #2-56, Hex 179627 4 Washer, #2, Flat 218018 2 Pop Rivet, SD64BS 11513

Note: Kneel ActuatorAssembly explodedview on opposite page.

Rep

air Parts

Decals

WARNING

Replace missing, wornor illegible decals.Failure to do so mayresult in serious bodilyinjury and/or propertydamage.

Decal Application Procedure

Clean “Mist-Grey” powder-coated surfaces (orpainted surfaces) with isopropyl alcohol beforedecal application. Use a clean cloth or papertowels. DO NOT use oily shop rags. Wipesurface free of residue with dry portion ofcleaning cloth.

Note: Pay close attention to the mask removalprocedure when posting die-cut decals.

Mask Removal

To remove the masking, start an edge and peelback slowly, at a sharp angle directly over the topof the decal.

Remember — the Entervan is only as safe as the operator.

Two Courtesy Requesteddecals are supplied withall Entervans to be postedon the vehicle as desired.

TM

12375

Fairfield, NJ USAOslo, Norway

Clearwater, FL USAKitchener, Ontario Can.

Huntington Beach, CA USARocklea, Queensland Aust.


1-800-THE LIFT (219) 946-6153 FAX: (219) 946-4670

Parking Courtesy Requested

The decals posted on yourEntervan are shown bymounting location. Partnumbers are provided forall decals. Inspect yourEntervan regularly for anymissing, worn or illegibledecals. Call 1-800-THELIFT for replacements.

ENTERTM

Locations:

• Posted on driver’s side door (top photo).

• Post on passenger’s side door (bottom photo).

Die-Cut Logo Decal Application:

1. Thoroughly clean the area where decal isto be applied with grease and waxremover. Dry completely.

2. Carefully remove backing paper fromdecal, making sure all pieces remainattached to carrier (masking paper).

3. Position decal as shown in photos (alignhorizontally with door panel).

4. Using a plastic squeegee, firmly press thedecal into place. Be certain all areashave been squeegeed thoroughly.

5. To remove the masking, start an edgeand peel back slowly at a sharp angle,directly over the top of the decal asshown above.

Courtesy RequestedDecal #12375

Actual Size: 3" Wide x 4" Tall

Entervan Logo Decal #51248

Actual Size: 14" x 2-1/2"

Rep

air Parts

Decals

Warnings and PowerOperation Instructions

Decal #52211

Actual Size:2-3/4" Wide x 8-9/16" Tall

Warnings and ManualOperation Instructions

Decal #52212

Actual Size:2-3/4" Wide x 9" Tall

Passive Access InstructionsDecal #18515

Actual Size: 2" Wide x 2-1/4" Tall

Posted on interior vertical face of rampmotor housing.

WARNING

Note: Engage vehicle transmissionin park, engage vehicle parking brake and press MANUAL/AUTO switch to MANUAL position before performing manual procedures.

Note: An assistant may be required to perform manual procedures.

TO OPEN DOOR:

1. Pull red manual door release handle UP fully. 2. Manually open door fully. 3. Push red manual door release handle DOWN fully.

TO UNFOLD RAMP:

1. Clear ramp path. 2. Push top of ramp out.

TO FOLD RAMP:

Manually lift and fold ramp fully.

TO CLOSE DOOR:

1. Pull red manual door release handle UP fully. 2. Manually close door fully. 3. Push red manual door release handle DOWN fully.

Note: Press MANUAL/AUTO switchto AUTO position before performingelectric procedures.

• Clear ramp path before performing manual unfold procedures. Ramp will free-fall.• Be certain door is fully open.• Keep clear of moving parts.

Failure to follow these rules may result in serious bodily injury and/or property damage.

MANUALOPERATION

52212

FOR PASSIVE (Non-Wheelchair)

ACCESS1. Press OPEN switch until door opens fully. Release switch.2. Pull cable knob UP to unlatch ramp.3. Manually rotate ramp OUT. 18515

Posted on front slide door post interior wallpanel adjacent to the latch release knob.

Posted on rear passenger-side interiorwall panel directly above ramp motorassembly.

Rep

air Parts

WARNING

POWEROPERATION

52211

Note: Engage vehicle transmission inPark, engage vehicle parking brake and press MANUAL/AUTO switch to AUTO position before operation.

FOR POWER KNEELING:

Press YES switch.

TO OPEN DOOR AND UNFOLD RAMP:

Press OPEN switch until door opens fully and ramp unfolds fully. Note: After door is fully open, a two second delay will occur before ramp starts to unfold.

TO FOLD RAMP AND CLOSE DOOR:

Press CLOSE switch until ramp folds fully and door closes fully.

TO TURN POWER KNEELING OFF:

Press NO switch.

• Read Entervan manual before operation.• Load and unload on level surface only.• Engage vehicle parking brake before operation.• Provide adequate clearance outside of vehicle to accommodate ramp.• Do not operate Entervan if you suspect damage, wear or any abnormal condition.• Keep clear of area in which door and ramp operate.• Close driver-side slide door before loading and unloading wheelchair passengers.

Failure to follow these rules may resultin serious bodily injury and/or property damage.





52215

MANUAL

AUTO

Decals

Kneel Actuator Manual ReleaseDecal #52215

Actual Size: 2-1/2" Wide x 3-1/8" Tall

Posted above kneel actuator manualrelease lever assembly mounting bracket.

Warning, Ramp Hazard (Rear)Decal #52206


Posted on ramp motor assembly cover.


52206


52207

Wall

Warning, Ramp Hazard (Front)Decal #52207


Posted on power slide door frontdoor post interior wall panel.

Power Slide DoorFront Door Post

Ramp MotorHousing Cover





52215

Rep

air Parts

Decals

Warning, Close Slide DoorDecal #52208


WARNINGClose slide door before loading and unloading wheelchair passengers.

52208

Door

Posted on driver's sideslide door interior panel.

Driver's Side Slide Door Interior Panel

Rep

air Parts


52217

Warning, Ramp Slope (Exterior)Decal #52217


Posted on passenger's side powerslide door window (outside).

Passenger's Side Slide Door


52205

Warning, Ramp Clearance (Exterior)Decal #52205


Posted on passenger's side powerslide door window (outside).


52205


52217

Rep

air Parts

Warning, Removable Front SeatDecal #18513

Actual Size: 3" Wide x 1-1/2" Tall

Posted on interior (inboard) face of seat base.Typical for both front seats. Driver's side seatshown - passenger's side seat is mirrored image.

WARNINGSeat securement devices must be fully engaged before occupying seat or operating vehicle. Failure to do so may result in serious bodily injury and/or property damage.

18513

WARNING

Seat securement devices must be fully

engaged before occupying seat or

operating vehicle. Failure to do so may

result in serious bodily injury and/or

property damage. 18513

Jacking InstructionsDecal #52214


Posted on driver's side end of tire rack.

WARNING

JACKINGINSTRUCTIONS

1. Press red KNEEL switch to NO position.

Note: If you have experienced power or equipment failure and the rear of the vehicle is in lowered position, refer to KNEEL ACTUATOR MANUAL RELEASE instruction decal #52215 posted on driver-side wall panel to raise vehicle.

2. Raise vehicle and change tire as instructed in Chrysler-supplied owner's manual.

Read jacking and tire changing safetyinstructions in Chrysler-suppliedowner's manual. Failure to do so may result in serious bodily injury and/or property damage.

52214

NOTICE: Jack stored behind spare tire.

Tire Rack

Caution, No Hand HoldDecal #13832

Actual Size: 2-11/16" Wide x 3/4" Tall

Posted on outboard face oframp rear side plate (portionabove bearing travel slot).

NO HAND HOLD13832

Decals

Decals

Rep

air Parts

Notice, Jack LocationDecal #65234

Actual Size: 1-1/4" Wide x 3/4" Tall

Posted on removable electric panelaccess cover below panel latch handle.

NOTICEJack stored in spare tire rack.

65234

Harness & Fuse Panel #52911A96-03

Kn

eel #1K

neel #2

Kn

eel #3K

neel #4

Kn

eel #5K

neel #6

Ram

p #7

Ram

p #8

Do

or #9

Do

or #10

65240

Posted onrelay blocks.

Note: Decalis cut in twosections forplacement.

Posted on electric paneladjacent to terminal block.

Posted nextto time delay.

Posted on rearfuse block.

12

34

56

7

18532

Relay LabelsDecal #65240Actual Size:

5/8" Wide x 11-3/4" Tall

Terminal LabelsDecal #18532Actual Size:

1/2" Wide x 5-5/8" Tall

Fuse LabelsDecal #52216Actual Size:

1-5/8" Wide x 1/2" Tall

REMOTE5

25RAMP

KEY ENTRY5

25KNEEL

DOOR25

52210

5KNEEL #2

Specifications

The following specifications are basic to the 1996and newer Chrysler Entervan II.

Weight:• Overall Weight of Stock Van (depends on type

of van): Approximately 4050 pounds• Conversion Add-On Weight (depends on type

and options): Approximately 350 pounds

Power source is 12 VDC battery with negativeground.

Electromechanical Kneeling System incorporat-ing:• Factory (OEM) Chrysler leaf springs• Heavy-duty weatherproof linear actuator with

sealed proximity switch activating the actuatorelectric brake

• Industrial four-leaf roller chain• On/Off Switch• Electrical override

The performance data contained within the Opera-tions Cycle Times Chart provides general perfor-mance criteria. This information is compiled fromtests conducted on standard Fully Automatic Series03 1996 and newer Chrysler Entervans meeting thefollowing constant operational specifications.

Operational Specifications:• Environmental temperature of 72° F. Extremely

low temperatures can moderately affect cycletime.

• Fully charged 12 volt DC power source. Lowvoltage will moderately affect test results.

• Door and ramp cycles timed with vehicle inkneeled (lowered) position.

Power Door Motor:• Type: Permanent Magnet• 12 VDC• Maximum Speed - 105 RPM• Maximum Torque: 120 inch pounds at 10 RPM• Approximately 1/50 Horsepower• Manual release (override)

Power Ramp Motor:• Type: Permanent Magnet• 12 VDC• 3 RPM• Torque: 1100 inch pounds• 1/17 Horsepower• Manual release (override)

Operation Duration (Min. to Max.)

Operations Cycle Times

Actuator Run Time

Lower Time only

Kneel (Down)

Door Open

Door Close

Ramp Fold

Ramp Unfold

Kneel (Up)Actuator Run Time

Raise Time only

Motor Run Time only

Fully Deployed

9.14 sec. to 12.35 sec.

5.57 sec. to 7.12 sec.

9.06 sec. to 9.73 sec.

2.50 sec. to 3.60 sec.

6.86 sec. to 13.79 sec.

4.23 sec. to 4.96 sec.

8.78 sec. to 9.54 sec.

8.82 sec. to 11.00 sec.

4.62 sec. to 6.03 sec.

Sp

ecification

s & D

imen

sion

s

Dimensions

68-3/8"71"

52-3/4"57-1/2"

56"52-1/2"

38"28-3/4"30-1/2"

5"4-5/8" Raised & 3-1/2" Lowered

9" Raised & 7-3/4" Lowered

47"80"55"

65-1/2"57-1/2"

ABCDEFGHIJKLMNOPQ

Dimension Description Chart Reference Dimension

H

I

F

Q

N

M

OP

G

Overall Height of VanOverall Height of Van with Luggage RackDoor Opening Usable Height (Slide Doors)

Interior Height at Center of VanInterior Height at Driver and Passenger PositionRamp Length

Ramp Length (First Section Only)Ramp Width (Usable Clear Opening)Ramp Width

Ground Clearance at FrameGround Clearance at Slide DoorsHeight at Floor

Interior Floor Length (Flat Ramp Area)Overall Interior Floor LengthInterior Width Behind Driver's Seat

Interior Width at Middle of RampInterior Width (to Ramp Motor)

C D

J

AB

KL

E

Sp

ecification

s & D

imen

sion

s

Warranty

Entervan frame and floor structural components

Entervan ramp, door and associated structural components

Entervan electrical components including but not limited toswitches, relays, connectors and solenoids

Entervan electromechanical kneel systems including but notlimited to electric actuator, chain, pulleys and associated hard-ware

Entervan appearance items including but not limited to interiorfloor covering and slide door lowered extension assemblies.

Corrosion Warranty:

Entervan frame, floor and lower door modification metal fabrica-tion corrosion applies to perforation only. Entervan lower slidedoor modification corrosion applies to outer-body sheet metal andpaint. Perforation is a rust-through condition such as an actualhole in the metal.

Years/Miles in Service Specific Area Covered

36 Monthsor

36,000 Miles(whichever comes first)

In accordance with the Chrysler 7 year/100,000mile corrosion warranty, The Braun Corporationwarrants to the purchaser of its Entervan conversionthat the metal fabrication on or of the frame, floorand lowered door extension are free from defects inmaterial and factory workmanship for a period of 7years or 100,000 miles on the odometer, whicheveroccurs first. The Braun Corporation further warrantsto the purchaser that the remainder of the modifica-

tions and alterations for associated parts are freefrom defects in material and workmanship for aperiod of 36 months or 36,000 miles, whichevercomes first. For clarification purposes, the followingchart outlines The Braun Corporation Entervanwarranty coverage. Refer to your Chrysler warrantyinformation booklet for all Chrysler OEM (factory)limited warranty details.

Both the 7 year/100,000 mile corrosion and the 3year/36,000 mile warranties described abovecommence on the date the conversion is put intoservice, providing the warranty registration card iscompleted and received by The Braun Corporationwithin thirty days of the purchase.

The Braun Corporation agrees to repair orreplace any of its Entervan factory-installed partsfound to be defective within the appropriate warranty

period or mileage. This warranty also covers thecost of labor for the repair or replacement of saidparts for one year provided that the repair is autho-rized by The Braun Corporation and carried out byan authorized service establishment (a Braun laborschedule determines the cost allowance for repairs).The Braun Corporation will not honor any warrantyclaim for repairs or replacement of parts unless theclaim is submitted with the appropriate factorywarranty authorization data and the repairs or

7 Yearor

100,000 Miles(whichever comes first)

CorrosionWarranty

see *Exceptions at right* Exceptions: Cosmetic or surface corrosion (resulting from stone

chips for example) would not be covered or repaired under thiscoverage. If corrosion does not cause holes, and is not theresult of usage and/or environmental conditions, repair cover-age lasts for 3 years or 36,000 miles, whichever comes first.

Warran

ty

Warranty

1014 S. MONTICELLO P.O. BOX 310 WINAMAC, IN. 46996 219•946•6153

Sample:Identification Decal

VIN # 1B4GP54R4TB154992ENTERVAN # 5200096 SERIAL 1203ENG. SERIES 03 ENG. RAMP SERIES 02MFG 07/20/96 DOOR OP. SERIES 02PAINT CODE INT - DIU35799KNEELING 1 EXT - DBU5069

VehicleIdentification

Number

EntervanModel Number

EngineeringSeries Number

Entervan Dateof Manufacture

SerialNumber

Engineering RampSeries Number

Door OperatorSeries Number

Sample:Return Authorization Tag

Date ReceivedAuthorized By

The Braun Corporation1014 S. Monticello StreetP.O. Box 310Winamac, IN 46996

Attn:(219) 946-6153 ENTER

TM

RETURN AUTHORIZATION TAG ENTERTM

Items below MUST be completed before credit will be issued

Returnee NameAccount #Replacement Invoice #

Entervan #

Example

Mfg. Date

Brief description of problem

This number will be located at driver side door jamb area

Return Authorization Procedure

you proper credit for warranty. The return authoriza-tion tag must be filled out with the appropriateEntervan model number, series numbers and serialnumber. The Entervan identification decal contain-ing the identification information is located on thedriver's door jamb. When filling out the yellow tag,please describe the problem briefly.

All parts under warranty must have a yellow returnauthorization tag attached before returning the partfor credit. A return authorization tag must be at-tached to every item and returned, freight prepaid,to The Braun Corporation. Yellow tags will be sentalong with the new replacement part. The authori-zation of yellow tags allows us to expediently give

Further, this warranty shall not extend to parts orworkmanship that may become defective becauseof the failure of anyone to operate the same inaccordance with the printed instructions of TheBraun Corporation or because of operation of thesame beyond its capacity.

Second buyers of a Braun Entervan conversionmay transfer the remaining warranty, if any, byobtaining a transfer of warranty application from TheBraun Corporation. This application must bereturned to The Braun Corporation within thirty daysfrom the date you purchase the vehicle and proof ofthe date of purchasing must be supplied with thetransfer of warranty application. There will be aminimum warranty transfer fee.

The Braun Corporation shall not be liable for anyincidental or consequential damages resulting fromany breach of warranty.

The Braun Corporation shall not be liable fortowing charges, travel and lodging, or any otherexpense incurred due to the loss of use of vehicle orother reason.

replacement of the parts are completed by a factory-authorized repairman. The factory authorizationdata, together with the name and location of thefactory-authorized repairman, can be obtained byeither written or telephone contact with The BraunCorporation at the addresses appearing in thismanual.

The return authorization procedure must beadhered to in order to process any warranty andrepair claims (details below).

The Braun Corporation reserves the right todesignate where any warranty work is to be per-formed.

The Braun Corporation also reserves the right toexamine any defective workmanship or part prior toany authorization of necessary repairs. This Enter-van warranty is not intended to replace or substituteany other warranties issued by the original manufac-turer of the vehicle or other suppliers of compo-nents. This warranty shall not apply to any part orworkmanship that may become defective due tomisuse, neglect, accident or other casualty, modifi-cations or alterations or unauthorized repairs.

5200096 - 03 - 1203 - 02 - 02 - 1

Warran

ty

Over 300 Braun Dealers and Distributors Worldwide

"Providing Access to the World"

®

"Providing Access to the World"

International Corporate Hdqrs: P.O. Box 310 Winamac, IN 46996 USA1-800-THE LIFT (219) 946-6153 FAX: (219) 946-4670

ENTERENTERTM

© The Braun Corporation 1996

MADE INAMERICA

®


1-800-THE LIFT (219) 946-6153 FAX: (219) 946-4670

Braun Chrysler Entervan®

Limited WarrantyThe Braun Corporation agrees to repair or replace any of its Entervan factory-

installed parts found to be defective within the appropriate warranty period or mileage. Thiswarranty also covers the cost of labor for the repair or replacement of said parts for one yearprovided that the repair is authorized by Braun and carried out by an authorized serviceestablishment (a Braun labor schedule determines the cost allowance for repairs). The BraunCorporation will not honor any warranty claim for repairs or replacement of parts unless theclaim is submitted with the appropriate factory warranty authorization data and the repairs orreplacement of the parts are completed by a factory-authorized repairman. The factoryauthorization data, together with the name and location of the factory-authorized repairman,can be obtained by either written or telephone contact with The Braun Corporation at theaddress listed below.

The return authorization procedure must be adhered to in order to process anywarranty and repair claims.

The Braun Corporation reserves the right to designate where any warranty work isto be performed.

The Braun Corporation also reserves the right to examine any defective workman-ship or part prior to any authorization of necessary repairs. This Entervan warranty isn’tintended to replace or substitute any other warranties issued by the original manufacturer ofthe vehicle or other suppliers or components. This warranty shall not apply to any part orworkmanship that may become defective due to misuse, neglect, accident or other casualty,modifications or alterations or unauthorized repairs. Further, this warranty shall not extend toparts or workmanship that may become defective because of the failure of anyone to operatethe same in accordance with the printed instructions of The Braun Corporation or because ofoperation of the same beyond its capacity.

Second buyers of a Braun Entervan conversion may transfer the remainingwarranty, if any, by obtaining a transfer of warranty application from The Braun Corporation.This application must be returned to The Braun Corporation within thirty days from the dateyou purchase the vehicle and proof of the date of purchasing must be supplied with thetransfer of warranty application. There will be a minimum warranty transfer fee.

The Braun Corporation shall not be liable for any incidental or consequentialdamages resulting from any breach of warranty.

The Braun Corporation shall not be liable for towing charges, travel and lodging, orany other expense incurred due to the loss of use of vehicle or other reason.

Note: See Warranty section within manual for detailed warranty coverage chart.

Braun Series 03 and later 1996 and newer Chrysler Entervan IIBraun Series 03 and later 1996 and newer Chrysler Entervan II®®

nu

arB

sei

reS

03

an

dr

etal

r

els

y rh

C r

ew

en

dn

a 6

99

1n

avr

etn

E®

II

All illustrations, descriptions and specifications in this manual are based on the latest product information available at the time of publication.The Braun Corporation reserves the right to make changes at any time without notice.

September 1996

5230096-03 August 1998Revision

tm owner's/service manual for series 03 and later fully

Documents