tm 10-3510-226-10-hr - liberated manuals.com · tm 10-3510-226-10-hr. hand receipt . covering ....

TM 10-3510-226-10-HR

HAND RECEIPT

COVERING CONTENTS OF COMPONENTS OF END ITEM (COEI),

BASIC ISSUE ITEMS (BII), AND ADDITIONAL AUTHORIZED LIST (AAL)

CONTAINERIZED BATCH LAUNDRY (CBL)

NSN 3510-01-527-2209 NSN 3510-01-527-2210

DISTRIBUTION STATEMENT A – Approved for public release; distribution is unlimited.

HEADQUARTERS, DEPARTMENT OF THE ARMY

31 AUGUST 2005

TM 10-3510-226-10-HR

HAND RECEIPT DEPARTMENT OF THE ARMY TM 10-3510-226-10-HR WASHINGTON, D.C., 31 August 2005

i

HAND RECEIPT

COVERING CONTENTS OF COMPONENTS OF END ITEM (COEI),

BASIC ISSUE ITEMS (BII), AND ADDITIONAL AUTHORIZED LIST (AAL)


NSN 3510-01-527-2209 NSN 3510-01-527-2210

REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS

You can help improve this manual. If you find any mistakes or if you know of a way to improve the procedures, please let us know. Mail your letter together with DA Form 2028 (Recommended Changes to Publications and Blank Forms), located in the back of this manual, direct to: Commander, U.S. Army Tank-automotive & Armaments Command, ATTN: AMSTA-LC-CECT, Kansas Street, Natick, MA 01760-5052. You may also send in your recommended changes via electronic mail directly to amssbriml @natick.army.mil. A reply will be furnished to you. Instructions for sending an electronic 2028 may be found at the back of this manual immediately preceding the hard copy 2028.

DISTRIBUTION STATEMENT A. – Approved for public release. Distribution is unlimited.

TABLE OF CONTENTS PAGE Section I. INTRODUCTION...............................................................................................................ii Section II. HAND RECEIPT.............................................................................................................. 1

TM 10-3510-226-10-HR

ii

Section I. INTRODUCTION

1. Scope This publication provides an overprinted DA Form 2062 (Hand Receipt) which lists the contents of Components of End Item (COEI), Basic Issue Items (BII), and Additional Authorization List (AAL) items related to the Containerized Batch Laundry (CBL). 2. General

a. Section II is the overprinted DA Form 2062 which lists the line item entry for system/end item and the content of COEI and BII extracted from TM 10-3510-226-10. The listings consist of exactly the same items and are in the same sequence as those listings in TM 10-3510-226-10.

b. The overprinted DA Form 2062 will eliminate manual preparation of the form and will assist organizations in

inventorying and accounting for property as required by AR 710-2.

c. Local reproduction of the overprinted DA Form 2062 is authorized. However, organizations will comply with local policies in the reproduction of DA Form 2062 by office copying equipment, field printing plant, or duplicating plant facilities.

d. Additional copies of this publication may be requisitioned from the U.S. Army Publications Distribution Center,

1655 Woodson Road, St. Louis, MO. 63114-6181, in accordance with procedures in Chapter 12, DA PAM 25-33. 3. Explanation of Blocks and Columns (DA Form 2062) Refer to DA Pam 710-2-1, Chapter 6 for additional information required to complete DA Form 2062.

a. FROM. Enter the organization, unit section or squad which issues the property.

b. TO. Enter the Unit Identifier Code (UIC) and the hand receipt file number of the unit/personnel receiving the property.

c. HAND RECEIPT NUMBER. Enter a locally designated number. Use it to post the location of property in the

property book.

d. END ITEM STOCK NUMBER. Contains the National Stock Number (NSN) to the end item covered by the hand receipt.

e. END ITEM DESCRIPTION. Contains the end item short title.

f. PUBLICATION NUMBER. Contains the TM number of the technical manual containing the operator/crew

instructions for the equipment.

g. PUBLICATION DATE. Date of the operator/crew technical manual.

h. QUANTITY. Quantity of the end item covered by this hand receipt.

i. STOCK NUMBER. (Column a). National stock number of the item described. Items without stock numbers should be requisitioned by Commercial and Government Entity Code (CAGEC) and part number with exception data in accordance with AR 710-2

TM 10-3510-226-10-HR

iii

j. ITEM DESCRIPTION (Column b). Enter a description of the item, to include the make or model and the serial/USA number, followed by the item description of COEI and BII items. In addition, it will contain the 5-digit Commercial and Government Entity Code (CAGEC), Part Number (P/N), and “Used On Code”. The “Used On Code” will not be used in this manual. k. ARC (Column c). The Accounting Requirements Code (ARC) is provided here. One of the following ARC will apply:

NOTE

The Accounting Requirements Code (ARC) refers to property accountability, not the Recoverability Code (RC). The ARC and the RC are listed in the Army Master Data File (AMDF).

(N) for Nonexpendable Items not consumed in use, retaining their identity during use and requiring accountability be maintained throughout the life of the item.

(D) for Durable Nonconsumable components of sets, kits, outfits and assemblages; all tools in FSCs 5120, 5130, 5140, 5180, 5210, 5220, and 5280; and any other nonconsumable with a price in excess of $50.00 or less and not already “N”.

(X) for Expendable Items, regardless of type classification or price and which is consumed in use. Includes all class 9 repair parts. Items not consumed in use which cost $50.00 or less and not already “N” or “D”.

l. SEC (Column d). The Controlled Inventory Item Code (formerly SEC code) is entered here. This is a one-position code which indicates the security classification, security risks or pilferage controls required for storage or transportation of assets. Order of precedence of assignment codes is classified, sensitive, pilferable, unclassified, as applicable. Codes applicable to this hand receipt are as follows:

TM 10-3510-226-10-HR

iv

SEC CODE PHYSICAL SECURITY CODE A CONFIDENTIAL – Former Restricted Data B CONFIDENTIAL – Restricted Data C CONFIDENTIAL D CONFIDENTIAL – Cryptologic E SECRET – Cryptologic F TOP SECRET – Cryptologic G SECRET – Former Restricted Data H SECRET – Restricted data K TOP SECRET – Former Restricted Data L TOP SECRET – Restricted Data O Naval Nuclear Propulsion Information S SECRET T TOP SECRET

SEC CODE SENSITIVE ITEMS CODE

P Ammunition and Explosives Q An item which is a drug or other substance determined by the Director, Drug Enforcement

Administration (DEA), Department of Justice, to be designated schedule symbol III, IV or V, as defined in the Controlled Substance Act of 1970, and other items requiring vault storage.

7 Sensitive information, prior to disposal, all nameplates, label plates, tags, stickers, documents or markings, which relate items to weapons system end item application, must be removed and destroyed.

SEC CODE PILFERABLE ITEMS CODE

Aircraft engine equipment and parts M Hand tools and shop equipment N Firearms V Individual clothing and equipment W Office machines X Photographic equipment and supplies Y Communications/electronic equipment and parts Z Vehicular equipment and parts. Pilferable item, due to its size, shape and utility, which does not

fall under one of the above categories. Pilferage controls may be designated by the coding activity to items coded U (unclassified) by recoding the items to J.

m. UI (Column e). Unit of Issue. Refer to AR 708-1 and/or CDA PAM 18-1 (Catalog Data Activity) for explanation

of abbreviations used in this column.

TM 10-3510-226-10-HR

n. QTY AUTH (Column f). The quantity authorized to be on hand, or part of the end item. o. Quantity (Column g). Actual quantity on hand. To be filled in by the receiving unit/personnel. p. Page of Pages. Contains page number and total number of pages for the COEI, BII, and AAL portions of the hand receipt. Hand Receipt holder will initial each page number (only when two or more forms are involved). When hand receipt holders change, the old initials will be lined out, and the new hand receipt holder will initial each page. 4. Authorization Documents

a. Components of End Item (COEI) are authorized by the applicable Repair Parts and Special Tools List (RPSTL). b. Basic Issue Items (BII) are authorized by the applicable operator’s manual. c. Additional Authorization List (AAL) items are authorized by the appropriate MTOE, TDA, CTA, or JTA authorization

documents.

Section II. HAND RECEIPT

Following is the Hand Receipt for the Containerized Batch Laundry (CBL).

v/(vi Blank)

CONTAINERIZED BATCH LAUNDRY (CBL) HAND RECEIPT/ANNEX NUMBER For use of this form, see DA PAM 710-2-1. The proponent agency is ODCSLOG.

FROM: TO: HAND RECEIPT NUMBER

FOR ANNEX/CR ONLY

END ITEM STOCK NUMBER 3510-01-527-2209 3510-01-527-2210

END ITEM DESCRIPTION CONTAINERIZED BATCH LAUNDRY

PUBLICATION NUMBER

TM 10-3510-226-10

PUBLICATION DATE

31 AUGUST 05

QUANTITY 1

g. QUANTITY STOCK NUMBER

a.

ITEM DESCRIPTION

b. * c.

SEC d.

UI e.

QTY AUTH

f. A B C D E F

COMPONENTS OF END ITEM (COEI)

4120-01-449-0459 AIR COND 66000 BTU (94833) 9454100

N U EA 1

4520-01-367-2739 HEATER 12000 BTU PORT (90598) H120

N U EA 1

5430-01-470-7380 TANK, FABRIC, COLLAPSIBLE (05YK6) RCF-3K-W-OT

N U EA 2

TM

10-3510-226-10-HR

* WHEN USED AS A: HAND RECEIPT, enter Hand Receipt Annex Number HAND RECEIPT FOR QUARTERS FURNITURE, enter Condition Codes HAND RECEIPT ANNEX/COMPONENTS RECEIPT; enter Accounting Requirements Code (ARC). PAGE ___1___ OF __10___ PAGES

DA FORM 2062, JAN 82 EDITION OF JAN 58 IS OBSOLETE USAPPC V2.10

CURRENT AS OF: 31 AUGUST 2005 1

TM 10-3510-226-10-H

R

2



a.

ITEM DESCRIPTION

b. * c.

SEC d.

UI e.

QTY AUTH

f. A B C D E F

BASIC ISSUE ITEMS LIST (BII)

4510-01-214-9139 ADAPTER ASSEMBLY (Fuel Drum Adapter) (81337) 618285

N U EA 1

8415-00-082-6108 APRON IMPERMEABLE (58536) A-A-55063

X U EA 2

7920-01-503-1671 BROOM, PUSH (83421) 7920-00-NIB-0322

X U EA 1

7920-01-531-0637 BRUSH, SANITARY (39428) 9756T23

X U EA 1

6150-01-247-4781 CABLE ASSEMBLY (50-ft 60-AMP) (97403)13226E7023-2

N U EA 1

6150-01-220-5587 CABLE ASSEMBLY (50-ft 100-Amp) (81349) MIL-C-29184

N U EA 3

6150-01-256-6301 CABLE PIGTAIL (4-ft 100-Amp) (97403)13226E7019

N U EA 3

7240-01-337-5269

CAN, GASOLINE, MILITARY (Olive Drab) (81349) A-A-59592

N U EA 1

OR OR

7240-01-337-5268

CAN, GASOLINE, MILITARY (sand) (81349) A-A-59592

N U EA 1

7240-00-160-0441 CAN, TRASH AND GARBAGE (39428) 9793506

N U EA 1

CIRCUIT BREAKER PANEL ACCESS KEY (56365) LP9618

N U EA 1

4310-01-531-0626 COMPRESSOR, UNIT RECIPROCATING (68821) CPFA2600P

N U EA 1

6150-01-516-2050 CORD EXTENSION (Extension Cord, 50-ft) (45152) 3375000

N U EA 4

Reverse of DA Form 2062 USAPPC V2.10 PAGE ____2___ OF _____10___ PAGES

CURRENT AS OF: 31 AUGUST 2005



a.

ITEM DESCRIPTION

b. * c.

SEC d.

UI e.

QTY AUTH

f. A B C D E F

(BII)-CONTINUED

7240-00-161-1147 COVER, CAN TRASH AND GARGABE (32 Gallon, Gray) (39428) 9793514

N U EA 1

DRYER KEY (59618) 70155601

N U EA 1

7290-00-616-0109 DUST PAN (58536) A-A-300

X U EA 1

6515-01-457-0631 FACE SHIELD HEAD GEAR (Double Matrix) (39428) 11618

X U EA 1

3510-01-531-0617 FACE SHIELD PROTECTION GUARD (1AG17) 76-1564-11

X U EA 1

4210-00-889-2491 FIRE EXTINGUISHER, 10-lb (80244) A-A-393, TY 1, CL 1, SZ10

N U EA 1

3990-01-531-0622

FIXTURE ASSEMBLY, STACKING (0U5N7) 43261127-2

N U EA 1

OR OR

3990-01-531-1958 FIXTURE ASSEMBLY, STACKING (0U5N7) 43261127-1

N U EA 1

7240-00-527-9868

FUNNEL, 32 OUNCE (39428) 89011616

X U EA 1

8415-01-463-5928 GLOVES, NATURAL RUBBER, SIZE MED/LG (39428) 23170ML

X U BX 1

8415-01-463-5922 GLOVES, NATURAL RUBBER, SIZE SM/MED (39428) 23170SM

X U BX 1

8415-00-266-8677 GLOVES, RUBBER, SIZE 10 (39428) 680-10

X U EA 2


X U EA 2


X U EA 2

4240-00-269-7912 GOGGLES, INDUSTRIAL (39428) 6636

X U EA 4

TM 10-3510-226-10-H

R

Reverse of DA Form 2062 USAPPC V2.10 PAGE _____3____ OF ___10_ PAGES

CURRENT AS OF: 31 AUGUST 2005 3

4 TM 10-3510-226-10-H

R

CONTAINERIZED BATCH LAUNDRY (CBL) g. QUANTITY STOCK NUMBER

a.

ITEM DESCRIPTION

b. * c.

SEC d.

UI e.

QTY AUTH

f. A B C D E F

(BII)-CONTINUED

4520-01-530-8693 HEATING ELEMENT ELECTRICAL, IMMERSION TYPE (81337) AP15N

N U EA 2

4720-00-077-0905 HOSE, ASSEMBLY, FUEL (1 Supply, 1 Return) (0U5N7) 43261146

N U EA 2

4720-01-531-0616 HOSE ASSEMBLY, NONMETALLIC (0U5N7) 43261150

N U EA 1

4720-01-531-0620 HOSE ASSEMBLY, NONMETALLIC (0U5N7) 43261151

N U EA 1

4720-01-531-0621 HOSE ASSEMBLY, NONMETALLIC (20-ft length, 2-in. diameter) (0U5N7) 43261152

N U EA 2

INSULATED LINER for 3000-GALLON WATER TANK GREEN (Top/Bottom Section) (81337)

N U EA 1

OR

INSULATED LINER for 3000-GALLON WATER TANK (Top/Bottom Section) N U EA 2

INSULATED LINER for 3000-GALLON WATER TANK (Left Side Section) (81337) 9-1-0829-GRN

N U EA 1

OR

INSULATED LINER for 3000-GALLON WATER TANK (Left Side Section) (0U5N7) 9-1-0829-TAN

N U EA 1

INSULATED LINER for 3000-GALLON WATER TANK (Right Side Section) (81337) 9-1-0828-TAN

N U EA 1

OR

INSULATED LINER for 3000-GALLON WATER TANK (Right Side Section) (81337) 9-1-0828-GRN

N U EA 2

4240-00-262-7092 LENS, GOGGLES, INDUSTRIAL (80204) ANSI-1

X U EA 4

Reverse of DA Form 2062 USAPPC V2.10 PAGE ____4____ OF __10___ PAGES



a.

ITEM DESCRIPTION

b. * c.

SEC d.

UI e.

QTY AUTH

f. A B C D E F

(BII)-CONTINUED

6230-01-397-1428 LIGHT, EXTENSION (00L99) ACS-2425PL

N U EA 2

4240-01-247-2348 MASK, AIR FILTERING (50378) 8511N95

N U BX 1

7330-00-205-3096 MEASURE, LIQUID (58536) A-A-1751

N U EA 1

MOUNTING BASE PLATE (OU5N7) 43261106

N U EA 1

MSDS BOOK (0U5N7) 43269009

X U EA 1

5120-01-354-2770 NUT DRIVER (Solid Shaft, 5/16 in.) (33287) J-35993-5

D U EA 1

5340-01-531-1962

PLATE, MOUNTING (End Plate Stacking Feature, Green) (0U5N7) 43262251-1

N U EA 1

OR OR

5340-01-531-1963 PLATE, MOUNTING (End Plate Stacking Feature, Tan) (0U5N7) 43262251-2

N U EA 1

5340-01-531-0618 PLATE MOUNTING (Foot, Interface, FDECU) (0U5N7) 43262117

N U EA 2

5340-01-531-0619 PLATE MOUNTING (Removable End Plate Stacking Fixture, FDECU) (0U5N7) 43262270

N U EA 2

5340-01-531-1959 PLATE, MOUNTING (Tie-Down Offset Anchor Clamp for FDECU) (0U5N7) 43262297

N U EA 1

5340-01-531-1960 PLATE, MOUNTING (Tie-Down Offset Slide Clamp for FDECU) (0U5N7) 43262296

N U EA 1

RAMP SECTIONS (0U5N7) 43262134-3

N U EA 2

5975-00-878-3791 ROD, GROUND (SECT, Type III, Class B) (81348) W-R-550

N U EA 2

5120-00-060-2004 SCREWDRIVER, PHILLIPS Tip, SIZE #1, (39428) 84959329

D U EA 1

TM 10-3510-226-10-H

R

Reverse of DA Form 2062 USAPPC V2.10 PAGE ____5____ OF __10___ PAGES


5

TM 10-3510-226-10-H

R

6


a.

ITEM DESCRIPTION

b. * c.

SEC d.

UI e.

QTY AUTH

f. A B C D E F

(BII)-CONTINUED 5120-00-142-5279

SCREWDRIVER, STANDARD TIP (39428) 84959162

D U EA 1

5120-00-288-8739 SCREWDRIVER SET, JEWELER’S SWIVEL (33164) 250

D U EA 1

7340-00-240-7079 SPOON, FOOD SERVICE (58536) A-A-1082

N U EA 1

6110-01-242-6691 STAND, DISTRIBUTION (BOX, TEMPER) (81337) 1-6-6005

N U EA 1

5430-00-134-3196 STRAP WEBBING (cargo strap small) (19207) 8690494

X U EA 10

7110-01-415-6895 TABLE, FOLDING (81337) 623954

N U EA 4

8340-01-240-5854 TEMPER, ARCH ASSEMBLY (81337) 5-4-4006

N U EA 3

8340-01-186-3030 TEMPER, CONTAINER TENT PIN (81337) 5-4-8487-1

N U EA 1

8340-01-186-3029 TEMPER, CONTAINER, VESTIBULE (81337) 5-4-3374-1

N U EA 1

6150-01-470-1916 TEMPER, CONVENIENCE OUTLET, DUPLEX w/GFCI (81337) 9-1-0624-1

N U EA 4

8340-01-186-3013 TEMPER, COVER, TENT FRAME (81337) 5-4-3347-1

N U EA 1

8340-01-186-3009 TEMPER, EAVE EXTENDER (81337) 5-4-3341

N U EA 6

6110-01-251-0402 TEMPER, ELECTRIC DISTRIBUTION BOX (81337) 1-6-6041

N U EA 1

Reverse of DA Form 2062 USAPPC V2.10 PAGE ____6____ OF ___10__ PAGES CURRENT AS OF: 31 AUGUST 2005



a.

ITEM DESCRIPTION

b. * c.

SEC d.

UI e.

QTY AUTH

f. A B C D E F

(BII)-CONTINUED

8340-01-186-3014 TEMPER, END SECTION, ISO (81337) 5-4-3350-1

N U EA 1

OR OR

8340-01-198-7618 TEMPER, END SECTION, ISO (81337) 5-4-3350-2

N U EA 1

TEMPER, END SECTION, MODIFIED ISO (81337) 9-1-0586

N U EA 1

OR OR

TEMPER, END SECTION, MODIFIED ISO (81337) 9-1-0586

N U EA 1

8340-01-186-3025 TEMPER, FLOOR, INSULATED (81337) 5-4-3369

N U EA 2

8340-01-186-3024 TEMPER, FLOOR, TENT (81337) 5-4-3368-1

N U EA 2

8340-01-186-3027 TEMPER, FLOOR, TENT, VESTIBULE (81337) 5-4-3372-1

N U EA 1

8340-01-186-3018 TEMPER, FLY, TENT (81337) 5-4-3353-1

N U EA 1

OR OR

8340-01-198-5358 TEMPER, FLY, TENT (81337) 5-4-3353-2

N U EA 1

8340-01-186-3004 TEMPER, HEADER ASSEMBLY (81337) 5-4-3335

N U EA 3

6230-01-465-8931 TEMPER, LIGHT SET, GENERAL ILLUMINATION, ISO (06967) F131-5004M

N U ST 1

8340-01-211-6798 TEMPER, PLENUM, TENT (81337) 5-4-3620

N U EA 1

8340-01-186-3005 TEMPER, PURLIN ASSEMBLY (81337) 5-4-3336

N U EA 10

8340-01-186-3008 TEMPER, RIDGE EXTENDER (81337) 5-4-3340

N U EA 3

8465-01-220-1419 TEMPER, STRAP, LIGHT SUPPORT ASSEMBLY, TYPE I, ISO (81337) 5-4-4005

N U EA 2

TM 10-3510-226-10-H

R

Reverse of DA Form 2062 USAPPC V2.10 PAGE ____7____ OF __10___ PAGES CURRENT AS OF: 31 AUGUST 2005 7

TM 10-3510-226-10-H

R

8


a.

ITEM DESCRIPTION

b. * c.

SEC d.

UI e.

QTY AUTH

f. A B C D E F

(BII)-CONTINUED

TEMPER, TENT LINE, ENDWALL (81337) 5-4-3350-1-36

N U EA 4

TEMPER, TENT LINE, TENT FLY (81337) 5-4-3353-1-26

N U EA 6

TEMPER, TENT LINE, VESTIBULE (81337) 5-4-3370-1-20

N U EA 4

TEMPER, TENT LINE, WINDOW SECTION (81337) 5-4-3363-1-32

N U EA 8

8340-01-392-0921

TEMPER, TENT LINER, END SECTION TEMPERATE, GREEN (81337) MIL-T-44243

N U EA 1

OR OR

8340-01-213-9566 TEMPER, TENT LINER, END SECTION TEMPERATE, TROPICAL DESERT (81337) MIL-T-44243

N U EA 1

8340-00-823-7451 TEMPER, TENT PIN, STEEL, 12-in., ISO (81337) 5-4-791

N U EA 30

8340-00-261-9751 TEMPER, TENT PIN, Wood, 24-in., ISO (81337) 5-4-1

N U EA 15

8340-01-186-3010 TEMPER, VESTIBULE FRAME ASSEMBLY (81337) 5-4-3343

N U EA 3

8340-01-186-3026 TEMPER, VESTIBULE, TENT (81337) 5-4-3370

N U EA 1

OR OR N EAU 1

8340-01-198-7621 TEMPER, VESTIBULE, TENT (81337) 5-4-3371

N U EA 1

8340-01-186-3021 TEMPER, WINDOW SECTION, ISO (81337) 5-4-3363-1

N U EA 2

OR OR

8340-01-198-7619 TEMPER, WINDOW SECTION, ISO (81337) 5-4-3363-2

N U EA 2

3990-01-204-3009 TIE DOWN, CARGO (cargo strap large) (98313) FDC5770-5

N U EA 5

Reverse of DA Form 2062 USAPPC V2.10 PAGE ____8____ OF __10___ PAGES CURRENT AS OF: 31 AUGUST 2005


a.

ITEM DESCRIPTION

b. * c.

SEC d.

UI e.

QTY AUTH

f. A B C D E F

(BII)-CONTINUED TM 10-3510-226-10 N U EA 1 TM 10-3510-226-10-HR N U EA 1 TM 10-3510-226-23 N U EA 1

TM 10-3510-226-23P N U EA 1

TRANSFER TOP, LAUNDRY CART (0U5N7) 43262305

N U EA 1

3920-00-929-8588 TRK 37-1/2x26x291/2 (81349) A-A-50025

N U EA 2

8460-01-471-1035 TRUNK, LOCKER TYPE II (58536) A-A-59490

N U EA 1

WASHER CONTROL PANEL ACCESS KEY (59618) F160562

N U EA 1

WASHER PROGRAM KEY (59618) 9001756

N U EA 1

5120-00-278-0341 WRENCH, ADJUSTABLE (10”, CHROME, CRESCENT, 15/16 IN. CAPACITY) (39428) W-72

D U EA 1

5120-01-461-1810 WRENCH, STRAP LARGE SIZE 6 3/8 IN. DIA (39428) 54325A24

D U EA 1

TM 10-3510-226-10-H

R

Reverse of DA Form 2062 USAPPC V2.10 PAGE ____9____ OF ___10__ PAGES CURRENT AS OF: 31 AUGUST 2005

9

TM 10-3510-226-10-H

R

10


a.

ITEM DESCRIPTION

b. * c.

SEC d.

UI e.

QTY AUTH

f. A B C D E F

ADDITIONAL AUTHORIZED LIST (AAL)

7920-00-772-5800 BRUSH, SANITARY (58536) A-A-3069

X U EA 6

8415-00-753-6552 GLOVES, TAP TYPE2 M10 (81349) MIL-G-12223

X U PR 2

4240-00-190-6432 GOGGLES INDUSTRIAL (58536) A-A-1110

X U EA 2

5120-00-926-7116 MALLET, WOOD (6-in. FACE X 8-in. Long Head (80244) LLL-M-71 TY9

D U EA 1

Reverse of DA Form 2062 USAPPC V2.10 PAGE ___10____ OF ____10__ PAGES


ARMY TM 10-3510-226-10-HR By Order of the Secretary of the Army:

PETER J. SCHOOMAKER General, United States Army Chief of Staff

Official:

SANDRA R. RILEY Administrative Assistant to the Secretary of the Army 0522402 Distribution: To be distributed in accordance with initial distribution number (IDN) 256846 requirements for TM 10-3510-226-10-HR.

These are the instructions for sending an electronic 2028 The following format must be used if submitting an electronic 2028. The subject line must be exactly the same and all fields must be included; however only the following fields are mandatory: 1, 3, 4, 5, 6, 7, 8, 9, 10, 13, 15, 16, 17, and 27. From: "Whomever" <[email protected]> To: [email protected] Subject: DA Form 2028 1. From: Joe Smith 2. Unit: home 3. Address: 4300 Park 4. City: Hometown 5. St: MO 6. Zip: 77777 7. Date Sent: 19-OCT-93 8. Pub no: 55-2840-229-23 9. Pub Title: TM 10. Publication Date: 04-JUL-85 11. Change Number: 7 12. Submitter Rank: MSG 13. Submitter FName: Joe 14. Submitter MName: T 15. Submitter LName: Smith 16. Submitter Phone: 123-123-1234 17. Problem: 1 18. Page: 2 19. Paragraph: 3 20. Line: 4 21. NSN: 5 22. Reference: 6 23. Figure: 7 24. Table: 8 25. Item: 9 26. Total: 123 27. Text: This is the text for the problem below line 27.

RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS

For use of this form, see AR 25-30; the proponent agency is ODISC4.

Use Part II (reverse) for Repair Parts and Special Tool Lists (RPSTL) and Supply Catalogs/Supply Manuals (SC/SM).

DATE

21 October 2003

TO: (Forward to proponent of publication or form) (Include ZIP Code) US ARMY TANK AUTOMOTIVE AND ARMAMENT COMMAND ATTN: AMSTA-LC-CECT 15 KANSAS ST NATICK, MA 01760-5052

FROM: (Activity and location) (Include ZIP Code) PFC JANE DOE Co A 3RD Engineer Br. Ft Leonard Wood, MO 63108

PART I – ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS PUBLICATION/FORM NUMBER TM 10-1670-296-23&P

DATE 30 October 2002

TITLE Unit Manual for Ancillary Equipment for Low Velocity Air Drop Systems

ITEM NO.

PAGE NO.

PARA- GRAPH

LINE NO. *

FIGURE NO.

TABLE NO.

RECOMMENDED CHANGES AND REASON (Provide exact wording of recommended changes, if possible).

0036 00-2

1

In Table 1, Sewing Machine Code Symbols, the second sewing machine code symbol should be MDZZ not MD22 Change the manual to show Sewing Machine, Industrial: Zig-Zag; 308 stitch; medium-duty; NSN 3530-01-181-1421 as a MDZZ code symbol.

*Reference to line numbers within the paragraph or subparagraph. TYPED NAME, GRADE OR TITLE Jane Doe, PFC

TELEPHONE EXCHANGE/AUTOVON, PLUS EXTENSION (508) 233-4141 DSN 256-4141

SIGNATURE Jane Doe Jane Doe

DA FORM 2028, FEB 74 REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED. USAPPC V3.00

TO: (Forward direct to addressee listed in publication) US ARMY TANK AUTOMOTIVE AND ARMAMENT COMMAND ATTN: AMSTA-LC-CECT 15 KANSAS ST NATICK, MA 01760-5052

FROM: (Activity and location) (Include ZIP Code) PFC JANE DOE Co A 3RD Engineer Br. Ft Leonard Wood, MO 63108


PART II – REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS PUBLICATION NUMBER TM 10-1670-296-23&P


TITLE Unit Manual for Ancillary Equipment for Low Velocity Air Drop Systems

PAGE NO.

COLM

NO.

LINE NO.

NATIONAL STOCK

NUMBER

REFERENCE

NO.

FIGURE

NO.

ITEM NO.

TOTAL NO. OF MAJOR

ITEMS SUPPORTED

RECOMMENDED ACTION

0066 00-1

4

Callout 16 in figure 4 is pointed to a D-Ring.In the Repair Part List key for Figure 4, item 16 is called a Snap Hook. Please correct one or the other.

PART III – REMARKS (Any general remarks or recommendations, or suggestions for improvement of publications and blank forms. Additional blank sheets may be used if more space is needed.)

TYPED NAME, GRADE OR TITLE

TELEPHONE EXCHANGE/AUTOVON, PLUS EXTENSION

SIGNATURE

UASPPC V3.00

RECOMMENDED CHANGES TO PUBLICATIONS AND BLANK FORMS

For use of this form, see AR 25-30; the proponent agency is ODISC4.

Use Part II (reverse) for Repair Parts and Special Tool Lists (RPSTL) and Supply Catalogs/Supply Manuals (SC/SM).

DATE

TO: (Forward to proponent of publication or form) (Include ZIP Code) Commander U.S. Army Tank-automotive and Armament Command ATTN: AMSTA-LC-CECT Kansas Street, Natick, MA 01760-5052.

FROM: (Activity and location) (Include ZIP Code)

PART I – ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS PUBLICATION/FORM NUMBER TM 10-3510-226-10-HR

DATE 31 August 2005

TITLE Hand Receipt Covering Contents of Component of End Item (COEI) Basic Issue Items (BII), and Additional Authorized List (AAL) for Containerized Batch Laundry(CBL)

ITEM NO.

PAGE NO.

PARA- GRAPH

LINE NO. *

FIGURE NO.

TABLE NO.

RECOMMENDED CHANGES AND REASON (Provide exact wording of recommended changes, if possible).

*Reference to line numbers within the paragraph or subparagraph. TYPED NAME, GRADE OR TITLE TELEPHONE EXCHANGE/AUTOVON, PLUS

EXTENSION SIGNATURE

DA FORM 2028, FEB 74 REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED. USAPPC V3.00

TO: (Forward direct to addressee listed in publication) Commander U.S. Army Tank-automotive and Armament Command ATTN: AMSTA-LC-CECT Kansas Street, Natick, MA 01760-5052.

FROM: (Activity and location) (Include ZIP Code) DATE

PART II – REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS PUBLICATION NUMBER TM 10-3510-226-10-HR

DATE 31 August 2005

TITLE Hand Receipt Covering Contents of Component of End Item (COEI) Basic Issue Items (BII), and Additional Authorized List (AAL) for Containerized Batch Laundry(CBL)

PAGE NO.

COLM

NO.

LINE NO.

NATIONAL STOCK

NUMBER

REFERENCE

NO.

FIGURE

NO.

ITEM NO.

TOTAL NO. OF MAJOR

ITEMS SUPPORTED

RECOMMENDED ACTION

PART III – REMARKS (Any general remarks or recommendations, or suggestions for improvement of publications and blank forms. Additional blank sheets may be used if more space is needed.)

TYPED NAME, GRADE OR TITLE TELEPHONE EXCHANGE/AUTOVON, PLUS EXTENSION SIGNATURE

UASPPC V3.00

These are the instructions for sending an electronic 2028 The following format must be used if submitting an electronic 2028. The subject line must be exactly the same and all fields must be included; however only the following fields are mandatory: 1, 3, 4, 5, 6, 7, 8, 9, 10, 13, 15, 16, 17, and 27. From: "Whomever" <[email protected]> To: [email protected] Subject: DA Form 2028 1. From: Joe Smith 2. Unit: home 3. Address: 4300 Park 4. City: Hometown 5. St: MO 6. Zip: 77777 7. Date Sent: 19-OCT-93 8. Pub no: 55-2840-229-23 9. Pub Title: TM 10. Publication Date: 04-JUL-85 11. Change Number: 7 12. Submitter Rank: MSG 13. Submitter FName: Joe 14. Submitter MName: T 15. Submitter LName: Smith 16. Submitter Phone: 123-123-1234 17. Problem: 1 18. Page: 2 19. Paragraph: 3 20. Line: 4 21. NSN: 5 22. Reference: 6 23. Figure: 7 24. Table: 8 25. Item: 9 26. Total: 123 27. Text: This is the text for the problem below line 27.

PIN: 082611-000

This fine document...

Was brought to you by me:

Liberated Manuals -- free army and government manuals

Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly available information, slap “watermarks” and other junk on it, and sell it. Those masters of search engine manipulation make sure that their sites that sell free information, come up first in search engines. They did not create it... They did not even scan it... Why should they get your money? Why are not letting you give those free manuals to your friends?

I am setting this document FREE. This document was made by the US Government and is NOT protected by Copyright. Feel free to share, republish, sell and so on.

I am not asking you for donations, fees or handouts. If you can, please provide a link to liberatedmanuals.com, so that free manuals come up first in search engines:

<A HREF=http://www.liberatedmanuals.com/>Free Military and Government Manuals</A>

– SincerelyIgor Chudovhttp://igor.chudov.com/

– Chicago Machinery Movers

http://www.liberatedmanuals.com/

https://www.machinerymoverschicago.com/

http://igor.chudov.com/

http://www.liberatedmanuals.com/