title weight and balance manual supplement ...this supplement provides specific weight and balance...

TITLE Page 1/1 10594 Ancra Proprietary Nov 17

TITLE

WEIGHT AND BALANCE MANUAL SUPPLEMENT

FOR ANCRA CARGO HANDLING SYSTEM

PART NUMBERS 85600-10 & 85600-17

DESIGNED FOR INSTALLATION ON

BOEING 737-800BCF AIRCRAFTS

Document No. 10594

Rev. C

ANCRA INTERNATIONAL LLC 875 West 8th Street AZUSA, CA 91702

Ancra International LLC proprietary rights are included in the information disclosed herein. Recipient, by accepting this document, agrees that neither this document nor the information disclosed herein nor any part thereof shall be reproduced or transferred to other documents or used or disclosed to others for manufacturing, technical or any other purpose except as specifically authorized in writing by Ancra International LLC.

Unpublished - all rights reserved under copyright laws. © 2017 Ancra International LLC

NOTICE Page 1/1 10594 Ancra Proprietary Nov 17

IMPORTANT NOTICE

This Supplement is incomplete without concurrent use of the applicable Boeing Weight and Balance Manual.

The information contained in this document supplements the information in the above manual in the areas shown

as pertains to the applicable Ancra 85600-10 and 85600-17 Cargo Handling Systems.

In no case, shall the information contained in this Supplement be interpreted to extend or change any other

operational limitations or procedures of the 737-800BCF aircraft as specified in the APPLICABLE BOEING

MANUAL. If areas of inconsistency are discovered, the applicable Boeing manual must take precedence.

INTRODUCTION Page 1/1 10594 Ancra Proprietary Nov 17

INTRODUCTION

This supplement provides specific Weight and Balance information for 737-800BCF aircraft, using Ancra Cargo

Handling Systems (CHS), P/N 85600-10 & 85600-17.

REVISIONS Page 1/1 10594 Ancra Proprietary Nov 17

REVISIONS

LTR DATE PREPARED BY CHECKED BY DESCRIPTION A SEPTEMBER 2017 S. ZADOIAN J. ROWLES INITIAL RELEASE

B OCTOBER 2017 S. ZADOIAN J. ROWLES CHANGE REVSION LEVEL ON TITEL PAGE.

CHANGING THIS PAGE TO DESCRIBE THE CHANGES IN REV B OF THE DOCUMENT.

UPDATED THE LIST OF EFFECTIVE PAGES TO IDENTIFY THE REVISED PAGES.

FIXED TYPOS (“OR LESSERIN” BECAME “OR LESS”) IN SECOND PAGE OF SECTION

1-64-01 & 1-64-02.

C NOVEMBER 2017 S. ZADOIAN J. ROWLES ADDED/FIXED REPORT NUMBER TO THE FOOTER OF ALL PAGES

CHANGE REVSION LEVEL ON TITEL PAGE.

CHANGING THIS PAGE TO DESCRIBE THE CHANGES IN REV B OF THE DOCUMENT.

UPDATED THE LIST OF EFFECTIVE PAGES TO IDENTIFY THE REVISED PAGES.

SECTION 1-64-00

O PARAGRAPH 1, REPLACED ICD REFERENCE WITH “THE CARGO”

O PARAGRAPH 1.2.1, CHANGED CG HEIGHT FROM 48 TO 36 INCHES

O FIGURE 1-64-00-1, ADDED FWD INDICATION ARROW








O PARAGRAPH 1.3, REPLACED THE PHRASE “SAFETY BARRIER NET” WITH “RIGID

CARGO BARRIER”

SECTION 1-64-01

O CAUTION 1, FIXED TYPO

O CAUTION 3, REPHRASED


O CAUTION 6, REPLACED ICD REFERENCE WITH “APPLICABLE BOEING MANUAL”

SECTION 1-64-02


O CAUTION 3, REPHRASED




EFFECTIVE PAGES Page 1/2 10594 Ancra Proprietary Nov 17

LIST OF EFFECTIVE PAGES

N =NEW R = REVISED D = DELETED

STATUS CH.SEC.SUB PAGE DATE

R TITLE 1 NOV 17

R IMPORTANT NOTICE 1 NOV 17

R INTRODUCTION 1 NOV 17

R REVISIONS 1 NOV 17

R LIST OF EFFECTIVE PAGES 1 NOV 17

R LIST OF MAIN MODIFICATIONS AFFECTING THIS MANUAL 1 NOV 17

R TABLE OF CONTENTS 1 NOV 17

R LIST OF FIGURES 1 NOV 17

R LIST OF TABLES 1 NOV 17

R 1 - CARGO LIMITATION (1-64-00) 1 NOV 17

R 1.1 - UNIT LOAD DEVICE (ULD) LIMITATIONS 1 NOV 17

R 1.2 - ULD CENTER OF GRAVITY (CG) LIMITS 1 NOV 17

R 1.2.1 - A SIZE ULD LATERALLY LOADED CG LIMITATIONS 1 NOV 17

R 1.2.2 - B SIZE (463L TYPE) ULD LATERALLY LOADED CG LIMITATIONS 2 NOV 17

R 1.2.3 - M SIZE ULD LATERALLY LOADED CG LIMITATIONS 2 NOV 17

R 1.2.4 - M SIZE ULD LONGITUDINALLY LOADED CG LIMITATIONS 3 NOV 17

R 1.2.5 - K SIZE ULD LONGITUDINALLY LOADED CG LIMITATIONS 3 NOV 17

R 1.3 - MAIN DECK LOADING 4 NOV 17

R 1.3.1 - CONFIGURATIONS 4 NOV 17

R 1.3.1.1 - (11) 88”X125” ULDS LOADED TRANSVERSELY PLUS (1) 60.4”X61.5” ULD 4 NOV 17

R 1.3.1.2 - (11) 88”X108” 463L ULDS LOADED TRANSVERSELY PLUS (1) 60.4”X61.5” ULD 4 NOV 17

R 1.3.1.3 - (10) 96”X125” ULDS LOADED TRANSVERSELY PLUS (1) 60.4”X61.5” ULD 4 NOV 17

R 1.3.1.4 - (9) 88”X125” ULDS LOADED TRANSVERSELY PLUS (1) 96”X125” ULD LOADED LONGITUDINALLY PLUS (1) 60.4”X61.5” ULD 5 NOV 17

R 1.3.1.5 - (8) 96”X125” ULDS LOADED TRANSVERSELY PLUS (1) 96”X125” ULD LOADED LONGITUDINALLY PLUS (1) 60.4”X61.5” ULD 5 NOV 17

R 1.3.2 - GEOMETRY (H-ARM & Y-ARM) 6 NOV 17

R 1.3.2.1 - A SIZE ULDS 6 NOV 17

R 1.3.2.2 - B SIZE ULDS 7 NOV 17

R 1.3.2.3 - M SIZE ULDS 8 NOV 17

R 1.3.2.4 - K SIZE ULD 9 NOV 17


R 2.1 - 85600-10 CHS EQUIPMENT MALFUNCTION LIMITATION 1 NOV 17

R 2.1.1 - ELEVEN (11) 88”X125” ULDS LOADED TRANSVERSELY PLUS ONE (1) 60.4”X61.5” ULD 3 NOV 17

R 2.1.1.1 - A1 (88”X125”) ULD 3 NOV 17

R 2.1.1.2 - A2 (88”X125”) ULD 4 NOV 17

R 2.1.1.3 - A3 (88”X125”) ULD 5 NOV 17

R 2.1.1.4 - A4 (88”X125”) ULD 6 NOV 17

R 2.1.1.5 - A5 (88”X125”) ULD 7 NOV 17

R 2.1.1.6 - A6 (88”X125”) ULD 8 NOV 17

R 2.1.1.7 - A7 (88”X125”) ULD 9 NOV 17

R 2.1.1.8 - A8 (88”X125”) ULD 10 NOV 17

R 2.1.1.9 - A9 (88”X125”) ULD 11 NOV 17

R 2.1.1.10 - A10 (88”X125”) ULD 12 NOV 17

R 2.1.1.11 - A11 (88”X125”) ULD 13 NOV 17

R 2.1.1.12 - K12 (60.4”X61.5”) ULD 14 NOV 17

R 2.2 - 85600-10 CHS COMPONENT AND SYSTEM WEIGHT 15 NOV 17

R 2.2 - 85600-10 CHS COMPONENT AND SYSTEM WEIGHT 16 NOV 17


R 3.1 - 85600-17 CHS EQUIPMENT MALFUNCTION LIMITATION 1 NOV 17

R 3.1.1 - ELEVEN (11) 88”X125” ULDS LOADED TRANSVERSELY PLUS ONE (1) 60.4”X61.5” ULD 3 NOV 17

R 3.1.1.1 - A1 (88”X125”) ULD 3 NOV 17

R 3.1.1.2 - A2 (88”X125”) ULD 4 NOV 17

R 3.1.1.3 - A3 (88”X125”) ULD 5 NOV 17

R 3.1.1.4 - A4 (88”X125”) ULD 6 NOV 17

R 3.1.1.5 - A5 (88”X125”) ULD 7 NOV 17

R 3.1.1.6 - A6 (88”X125”) ULD 8 NOV 17

R 3.1.1.7 - A7 (88”X125”) ULD 9 NOV 17

R 3.1.1.8 - A8 (88”X125”) ULD 10 NOV 17

R 3.1.1.9 - A9 (88”X125”) ULD 11 NOV 17

R 3.1.1.10 - A10 (88”X125”) ULD 12 NOV 17

R 3.1.1.11 - K12 (60.4”X61.5”) ULD 13 NOV 17

R 3.1.2 - ELEVEN (11) 88”X108” 463L ULDS LOADED TRANSVERSELY PLUS ONE (1) 60.4”X61.5” ULD 14 NOV 17

R 3.1.2.1 - B1 (88”X108”) ULD 14 NOV 17

R 3.1.2.2 - B2 (88”X108”) ULD 15 NOV 17

EFFECTIVE PAGES Page 2/2 10594 Ancra Proprietary Nov 17

N =NEW R = REVISED D = DELETED

STATUS CH.SEC.SUB PAGE DATE

R 3.1.2.3 - B3 (88”X108”) ULD 16 NOV 17

R 3.1.2.4 - B4 (88”X108”) ULD 17 NOV 17

R 3.1.2.5 - B5 (88”X108”) ULD 18 NOV 17

R 3.1.2.6 - B6 (88”X108”) ULD 19 NOV 17

R 3.1.2.7 - B7 (88”X108”) ULD 20 NOV 17

R 3.1.2.8 - B8 (88”X108”) ULD 21 NOV 17

R 3.1.2.9 - B9 (88”X108”) ULD 22 NOV 17

R 3.1.2.10 - B10 (88”X108”) ULD 23 NOV 17

R 3.1.2.11 - B11 (88”X108”) ULD 24 NOV 17

R 3.1.2.12 - K12 (60.4”X61.5”) ULD 25 NOV 17

R 3.1.3 - TEN (10) 96”X125” ULDS LOADED TRANSVERSELY PLUS ONE (1) 60.4”X61.5” ULD 26 NOV 17

R 3.1.3.1 - M1 (96”X125”) ULD 26 NOV 17

R 3.1.3.2 - M2 (96”X125”) ULD 27 NOV 17

R 3.1.3.3 - M3 (96”X125”) ULD 28 NOV 17

R 3.1.3.4 - M4 (96”X125”) ULD 29 NOV 17

R 3.1.3.5 - M5 (96”X125”) ULD 30 NOV 17

R 3.1.3.6 - M6 (96”X125”) ULD 31 NOV 17

R 3.1.3.7 - M7 (96”X125”) ULD 32 NOV 17

R 3.1.3.8 - M8 (96”X125”) ULD 33 NOV 17

R 3.1.3.9 - M9 (96”X125”) ULD 34 NOV 17

R 3.1.3.10 - M10 (96”X125”) ULD 35 NOV 17

R 3.1.3.11 - K12 (60.4”X61.5”) ULD 36 NOV 17

R 3.1.4 - NINE (9) 88”X125” ULDS LOADED TRANSVERSELY PLUS ONE (1) 96”X125” ULD LOADED LONGITUDINALLY PLUS ONE (1) 60.4”X61.5” ULD.

37 NOV 17

R 3.1.4.1 - A1 (88”X125”) ULD 37 NOV 17

R 3.1.4.2 - A2 (88”X125”) ULD 38 NOV 17

R 3.1.4.3 - A3 (88”X125”) ULD 39 NOV 17

R 3.1.4.4 - A4 (88”X125”) ULD 40 NOV 17

R 3.1.4.5 - M5L (96”X125”) ULD 41 NOV 17

R 3.1.4.6 - A7 (88”X125”) ULD 42 NOV 17

R 3.1.4.7 - A8 (88”X125”) ULD 43 NOV 17

R 3.1.4.8 - A9 (88”X125”) ULD 44 NOV 17

R 3.1.4.9 - A10 (88”X125”) ULD 45 NOV 17

R 3.1.4.10 - A11 (88”X125”) ULD 46 NOV 17

R 3.1.4.11 - K12 (60.4”X61.5”) ULD 47 NOV 17

R 3.1.5 - EIGHT (8) 96”X125” ULDS LOADED TRANSVERSELY PLUS ONE (1) 96”X125” ULD LOADED LONGITUDINALLY PLUS ONE (1) 60.4”X61.5” ULD

48 NOV 17

R 3.1.5.1 - M1 (96”X125”) ULD 48 NOV 17

R 3.1.5.2 - M2 (96”X125”) ULD 49 NOV 17

R 3.1.5.3 - M3 (96”X125”) ULD 50 NOV 17

R 3.1.5.4 - M4 (96”X125”) ULD 51 NOV 17

R 3.1.5.5 - M5L (96”X125”) ULD 52 NOV 17

R 3.1.5.6 - M7 (96”X125”) ULD 53 NOV 17

R 3.1.5.7 - M8 (96”X125”) ULD 54 NOV 17

R 3.1.5.8 - M9 (96”X125”) ULD 55 NOV 17

R 3.1.5.9 - M10 (96”X125”) ULD 56 NOV 17

R 3.1.5.10 - K12 (60.4”X61.5”) ULD 57 NOV 17

R 3.2 - 85600-17 CHS COMPONENT AND SYSTEM WEIGHTS 58 NOV 17

R 3.2 - 85600-17 CHS COMPONENT AND SYSTEM WEIGHTS 59 NOV 17

MOD Page 1/1 10594 Ancra Proprietary Nov 17

LIST OF MAIN MODIFICATIONS AFFECTING THIS MANUAL

MOD TITLE

Cargo Handling System Installation Ancra Cargo Handling Systems, P/N 85600-10 and 85600-17

TOC Page 1/3 10594 Ancra Proprietary Nov 17

TABLE OF CONTENTS

TITLE .................................................................................................................................................................................... 1

IMPORTANT NOTICE ............................................................................................................................................................ 1

INTRODUCTION ................................................................................................................................................................... 1

REVISIONS ........................................................................................................................................................................... 1

LIST OF EFFECTIVE PAGES ..................................................................................................................................................... 1

LIST OF MAIN MODIFICATIONS AFFECTING THIS MANUAL .................................................................................................. 1

TABLE OF CONTENTS ............................................................................................................................................................ 1

LIST OF FIGURES ................................................................................................................................................................... 1

LIST OF TABLES .................................................................................................................................................................... 1

1 CARGO LIMITATION (1-64-00) ..................................................................................................................................... 1

1.1 UNIT LOAD DEVICE (ULD) LIMITATIONS .............................................................................................................................. 1 1.2 ULD CENTER OF GRAVITY (CG) LIMITS ............................................................................................................................... 1

1.2.1 A Size ULD Laterally Loaded CG Limitations ........................................................................................................... 1 1.2.2 B Size (463L Type) ULD Laterally Loaded CG Limitations ....................................................................................... 2 1.2.3 M Size ULD Laterally Loaded CG Limitations ......................................................................................................... 2 1.2.4 M Size ULD Longitudinally Loaded CG Limitations ................................................................................................. 3 1.2.5 K Size ULD Longitudinally Loaded CG Limitations .................................................................................................. 3

1.3 MAIN DECK LOADING ...................................................................................................................................................... 4 1.3.1 Configurations........................................................................................................................................................ 4

1.3.1.1 (11) 88”x125” ULDs Loaded Transversely Plus (1) 60.4”x61.5” ULD ............................................................................... 4 1.3.1.2 (11) 88”x108” 463L ULDs Loaded Transversely Plus (1) 60.4”x61.5” ULD ...................................................................... 4 1.3.1.3 (10) 96”x125” ULDs Loaded Transversely Plus (1) 60.4”x61.5” ULD ............................................................................... 4 1.3.1.4 (9) 88”x125” ULDs Loaded Transversely Plus (1) 96”x125” ULD Loaded Longitudinally Plus (1) 60.4”x61.5” ULD ......... 5 1.3.1.5 (8) 96”x125” ULDs Loaded Transversely Plus (1) 96”x125” ULD Loaded Longitudinally Plus (1) 60.4”x61.5” ULD ......... 5

1.3.2 Geometry (H-Arm & Y-Arm) ................................................................................................................................... 6 1.3.2.1 A Size ULDs ...................................................................................................................................................................... 6 1.3.2.2 B Size ULDs ...................................................................................................................................................................... 7 1.3.2.3 M Size ULDs ..................................................................................................................................................................... 8 1.3.2.4 K Size ULD ....................................................................................................................................................................... 9


2.1 85600-10 CHS EQUIPMENT MALFUNCTION LIMITATION ...................................................................................................... 1 2.1.1 Eleven (11) 88”x125” ULDs Loaded Transversely Plus One (1) 60.4”x61.5” ULD ................................................... 3

2.1.1.1 A1 (88”x125”) ULD .......................................................................................................................................................... 3 2.1.1.2 A2 (88”x125”) ULD .......................................................................................................................................................... 4 2.1.1.3 A3 (88”x125”) ULD .......................................................................................................................................................... 5 2.1.1.4 A4 (88”x125”) ULD .......................................................................................................................................................... 6 2.1.1.5 A5 (88”x125”) ULD .......................................................................................................................................................... 7 2.1.1.6 A6 (88”x125”) ULD .......................................................................................................................................................... 8 2.1.1.7 A7 (88”x125”) ULD .......................................................................................................................................................... 9 2.1.1.8 A8 (88”x125”) ULD ........................................................................................................................................................ 10 2.1.1.9 A9 (88”x125”) ULD ........................................................................................................................................................ 11 2.1.1.10 A10 (88”x125”) ULD ...................................................................................................................................................... 12 2.1.1.11 A11 (88”x125”) ULD ...................................................................................................................................................... 13 2.1.1.12 K12 (60.4”x61.5”) ULD .................................................................................................................................................. 14

2.2 85600-10 CHS COMPONENT AND SYSTEM WEIGHT .......................................................................................................... 15



3.1 85600-17 CHS EQUIPMENT MALFUNCTION LIMITATION ...................................................................................................... 1 3.1.1 Eleven (11) 88”x125” ULDs Loaded Transversely Plus One (1) 60.4”x61.5” ULD ................................................... 3

3.1.1.1 A1 (88”x125”) ULD .......................................................................................................................................................... 3 3.1.1.2 A2 (88”x125”) ULD .......................................................................................................................................................... 4 3.1.1.3 A3 (88”x125”) ULD .......................................................................................................................................................... 5 3.1.1.4 A4 (88”x125”) ULD .......................................................................................................................................................... 6 3.1.1.5 A5 (88”x125”) ULD .......................................................................................................................................................... 7 3.1.1.6 A6 (88”x125”) ULD .......................................................................................................................................................... 8 3.1.1.7 A7 (88”x125”) ULD .......................................................................................................................................................... 9 3.1.1.8 A8 (88”x125”) ULD ........................................................................................................................................................ 10 3.1.1.9 A9 (88”x125”) ULD ........................................................................................................................................................ 11 3.1.1.10 A10 (88”x125”) ULD ...................................................................................................................................................... 12 3.1.1.11 K12 (60.4”x61.5”) ULD .................................................................................................................................................. 13

3.1.2 Eleven (11) 88”x108” 463L ULDs Loaded Transversely Plus One (1) 60.4”x61.5” ULD ........................................ 14 3.1.2.1 B1 (88”X108”) ULD ........................................................................................................................................................ 14 3.1.2.2 B2 (88”X108”) ULD ........................................................................................................................................................ 15 3.1.2.3 B3 (88”X108”) ULD ........................................................................................................................................................ 16 3.1.2.4 B4 (88”X108”) ULD ........................................................................................................................................................ 17 3.1.2.5 B5 (88”X108”) ULD ........................................................................................................................................................ 18 3.1.2.6 B6 (88”X108”) ULD ........................................................................................................................................................ 19 3.1.2.7 B7 (88”X108”) ULD ........................................................................................................................................................ 20 3.1.2.8 B8 (88”X108”) ULD ........................................................................................................................................................ 21 3.1.2.9 B9 (88”X108”) ULD ........................................................................................................................................................ 22 3.1.2.10 B10 (88”X108”) ULD ...................................................................................................................................................... 23 3.1.2.11 B11 (88”X108”) ULD ...................................................................................................................................................... 24 3.1.2.12 K12 (60.4”x61.5”) ULD .................................................................................................................................................. 25

3.1.3 Ten (10) 96”x125” ULDs Loaded Transversely Plus One (1) 60.4”x61.5” ULD...................................................... 26 3.1.3.1 M1 (96”X125”) ULD ....................................................................................................................................................... 26 3.1.3.2 M2 (96”X125”) ULD ....................................................................................................................................................... 27 3.1.3.3 M3 (96”X125”) ULD ....................................................................................................................................................... 28 3.1.3.4 M4 (96”X125”) ULD ....................................................................................................................................................... 29 3.1.3.5 M5 (96”X125”) ULD ....................................................................................................................................................... 30 3.1.3.6 M6 (96”X125”) ULD ....................................................................................................................................................... 31 3.1.3.7 M7 (96”X125”) ULD ....................................................................................................................................................... 32 3.1.3.8 M8 (96”X125”) ULD ....................................................................................................................................................... 33 3.1.3.9 M9 (96”X125”) ULD ....................................................................................................................................................... 34 3.1.3.10 M10 (96”X125”) ULD ..................................................................................................................................................... 35 3.1.3.11 K12 (60.4”x61.5”) ULD .................................................................................................................................................. 36

3.1.4 Nine (9) 88”x125” ULDs Loaded Transversely Plus One (1) 96”x125” ULD Loaded Longitudinally Plus One (1) 60.4”x61.5” ULD. ............................................................................................................................................................... 37

3.1.4.1 A1 (88”x125”) ULD ........................................................................................................................................................ 37 3.1.4.2 A2 (88”x125”) ULD ........................................................................................................................................................ 38 3.1.4.3 A3 (88”x125”) ULD ........................................................................................................................................................ 39 3.1.4.4 A4 (88”x125”) ULD ........................................................................................................................................................ 40 3.1.4.5 M5L (96”x125”) ULD ..................................................................................................................................................... 41 3.1.4.6 A7 (88”x125”) ULD ........................................................................................................................................................ 42 3.1.4.7 A8 (88”x125”) ULD ........................................................................................................................................................ 43 3.1.4.8 A9 (88”x125”) ULD ........................................................................................................................................................ 44 3.1.4.9 A10 (88”x125”) ULD ...................................................................................................................................................... 45 3.1.4.10 A11 (88”x125”) ULD ...................................................................................................................................................... 46 3.1.4.11 K12 (60.4”x61.5”) ULD .................................................................................................................................................. 47

3.1.5 Eight (8) 96”x125” ULDs Loaded Transversely Plus One (1) 96”x125” ULD Loaded Longitudinally Plus One (1) 60.4”x61.5” ULD ................................................................................................................................................................ 48

3.1.5.1 M1 (96”X125”) ULD ....................................................................................................................................................... 48 3.1.5.2 M2 (96”X125”) ULD ....................................................................................................................................................... 49 3.1.5.3 M3 (96”X125”) ULD ....................................................................................................................................................... 50 3.1.5.4 M4 (96”X125”) ULD ....................................................................................................................................................... 51 3.1.5.5 M5L (96”x125”) ULD ..................................................................................................................................................... 52


3.1.5.6 M7 (96”X125”) ULD ....................................................................................................................................................... 53 3.1.5.7 M8 (96”X125”) ULD ....................................................................................................................................................... 54 3.1.5.8 M9 (96”X125”) ULD ....................................................................................................................................................... 55 3.1.5.9 M10 (96”X125”) ULD ..................................................................................................................................................... 56 3.1.5.10 K12 (60.4”x61.5”) ULD .................................................................................................................................................. 57

3.2 85600-17 CHS COMPONENT AND SYSTEM WEIGHTS ......................................................................................................... 58

FIGURES Page 1/2 10594 Ancra Proprietary Nov 17

LIST OF FIGURES

FIGURE 1-64-00-1 – A SIZE ULD LATERALLY LOADED CG ....................................................................................................................... 1 FIGURE 1-64-00-2 – B SIZE (463L TYPE) ULD LATERALLY LOADED CG ..................................................................................................... 2 FIGURE 1-64-00-4 – M SIZE ULD LATERALLY LOADED CG ...................................................................................................................... 2 FIGURE 1-64-00-5 – M SIZE ULD LONGITUDINALLY LOADED CG ............................................................................................................. 3 FIGURE 1-64-00-6 – K SIZE ULD LONGITUDINALLY LOADED CG .............................................................................................................. 3 FIGURE 1-64-00-7 – (11) 88”X125” ULDS PLUS (1) 60.4”X61.5” ULD .............................................................................................. 4 FIGURE 1-64-00-8 – (11) 88”X108” 463L ULDS PLUS (1) 60.4”X61.5” ULD ........................................................................................ 4 FIGURE 1-64-00-9 – (10) 96”X125” ULDS PLUS (1) 60.4”X61.5” ULD ................................................................................................ 4 FIGURE 1-64-00-10 – (9) 88”X125” ULDS (1) 96”X125” ULD LONGITUDINAL PLUS (1) 60.4”X61.5” ULD ............................................... 5 FIGURE 1-64-00-11 – (8) 96”X125” ULDS PLUS (1) 96”X125” ULD LONGITUDINAL PLUS (1) 60.4”X61.5” ULD........................................ 5 FIGURE 1-64-00-12 – A SIZE ULDS GEOMETRY .................................................................................................................................... 6 FIGURE 1-64-00-13 – B SIZE ULDS GEOMETRY .................................................................................................................................... 7 FIGURE 1-64-00-14 – A SIZE ULDS GEOMETRY .................................................................................................................................... 8 FIGURE 1-64-00-15 – K SIZE ULDS GEOMETRY .................................................................................................................................... 9 FIGURE 1-64-01-16 – A1 ULD INSTALLED ON 85600-10 CHS ............................................................................................................... 3 FIGURE 1-64-01-17 – A2 ULD INSTALLED ON 85600-10 CHS ............................................................................................................... 4 FIGURE 1-64-01-18 – A3 ULD INSTALLED ON 85600-10 CHS ............................................................................................................... 5 FIGURE 1-64-01-19 – A4 ULD INSTALLED ON 85600-10 CHS ............................................................................................................... 6 FIGURE 1-64-01-20 – A5 ULD INSTALLED ON 85600-10 CHS ............................................................................................................... 7 FIGURE 1-64-01-21 – A6 ULD INSTALLED ON 85600-10 CHS ............................................................................................................... 8 FIGURE 1-64-01-22 – A7 ULD INSTALLED ON 85600-10 CHS ............................................................................................................... 9 FIGURE 1-64-01-23 – A8 ULD INSTALLED ON 85600-10 CHS ............................................................................................................. 10 FIGURE 1-64-01-24 – A9 ULD INSTALLED ON 85600-10 CHS ............................................................................................................. 11 FIGURE 1-64-01-25 – A10 ULD INSTALLED ON 85600-10 CHS ........................................................................................................... 12 FIGURE 1-64-01-26 – A11 ULD INSTALLED ON 85600-10 CHS ........................................................................................................... 13 FIGURE 1-64-01-27 – K12 ULD INSTALLED ON 85600-10 CHS ........................................................................................................... 14 FIGURE 1-64-02-28 – A1 ULD INSTALLED ON 85600-17 CHS ............................................................................................................... 3 FIGURE 1-64-02-29 – A2 ULD INSTALLED ON 85600-17 CHS ............................................................................................................... 4 FIGURE 1-64-02-30 – A3 ULD INSTALLED ON 85600-17 CHS ............................................................................................................... 5 FIGURE 1-64-02-31 – A4 ULD INSTALLED ON 85600-17 CHS ............................................................................................................... 6 FIGURE 1-64-02-32 – A5 ULD INSTALLED ON 85600-17 CHS ............................................................................................................... 7 FIGURE 1-64-02-33 – A6 ULD INSTALLED ON 85600-17 CHS ............................................................................................................... 8 FIGURE 1-64-02-34 – A7 ULD INSTALLED ON 85600-17 CHS ............................................................................................................... 9 FIGURE 1-64-02-35 – A8 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 10 FIGURE 1-64-02-36 – A9 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 11 FIGURE 1-64-02-37 – A10 ULD INSTALLED ON 85600-17 CHS ........................................................................................................... 12 FIGURE 1-64-02-38 – K12 ULD INSTALLED ON 85600-17 CHS ........................................................................................................... 13 FIGURE 1-64-02-39 – B1 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 14 FIGURE 1-64-02-40 – B2 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 15 FIGURE 1-64-02-41 – B3 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 16 FIGURE 1-64-02-42 – B4 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 17 FIGURE 1-64-02-43 – B5 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 18 FIGURE 1-64-02-44 – B6 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 19 FIGURE 1-64-02-45 – B7 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 20 FIGURE 1-64-02-46 – B8 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 21 FIGURE 1-64-02-47 – B9 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 22 FIGURE 1-64-02-48 – B10 ULD INSTALLED ON 85600-17 CHS ........................................................................................................... 23 FIGURE 1-64-02-49 – B11 ULD INSTALLED ON 85600-17 CHS ........................................................................................................... 24 FIGURE 1-64-02-50 – K12 ULD INSTALLED ON 85600-17 CHS ........................................................................................................... 25

FIGURES Page 2/2 10594 Ancra Proprietary Nov 17

FIGURE 1-64-02-51 – M1 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 26 FIGURE 1-64-02-52 – M2 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 27 FIGURE 1-64-02-53 – M3 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 28 FIGURE 1-64-02-54 – M4 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 29 FIGURE 1-64-02-55 – M5 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 30 FIGURE 1-64-02-56 – M6 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 31 FIGURE 1-64-02-57 – M7 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 32 FIGURE 1-64-02-58 – M8 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 33 FIGURE 1-64-02-59 – M9 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 34 FIGURE 1-64-02-60 – M10 ULD INSTALLED ON 85600-17 CHS .......................................................................................................... 35 FIGURE 1-64-02-61 – K12 ULD INSTALLED ON 85600-17 CHS ........................................................................................................... 36 FIGURE 1-64-02-62 – A1 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 37 FIGURE 1-64-02-63 – A2 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 38 FIGURE 1-64-02-64 – A3 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 39 FIGURE 1-64-02-65 – A4 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 40 FIGURE 1-64-02-66 – M5L ULD INSTALLED ON 85600-17 CHS .......................................................................................................... 41 FIGURE 1-64-02-67 – A7 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 42 FIGURE 1-64-02-68 – A8 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 43 FIGURE 1-64-02-69 – A9 ULD INSTALLED ON 85600-17 CHS ............................................................................................................. 44 FIGURE 1-64-02-70 – A10 ULD INSTALLED ON 85600-17 CHS ........................................................................................................... 45 FIGURE 1-64-02-71 – A11 ULD INSTALLED ON 85600-17 CHS ........................................................................................................... 46 FIGURE 1-64-02-72 – K12 ULD INSTALLED ON 85600-17 CHS ........................................................................................................... 47 FIGURE 1-64-02-73 – M1 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 48 FIGURE 1-64-02-74 – M2 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 49 FIGURE 1-64-02-75 – M3 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 50 FIGURE 1-64-02-76 – M4 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 51 FIGURE 1-64-02-77 – M5L ULD INSTALLED ON 85600-17 CHS .......................................................................................................... 52 FIGURE 1-64-02-78 – M7 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 53 FIGURE 1-64-02-79 – M8 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 54 FIGURE 1-64-02-80 – M9 ULD INSTALLED ON 85600-17 CHS ............................................................................................................ 55 FIGURE 1-64-02-81 – M10 ULD INSTALLED ON 85600-17 CHS .......................................................................................................... 56 FIGURE 1-64-02-82 – K12 ULD INSTALLED ON 85600-17 CHS ........................................................................................................... 57

TABLES Page 1/2 10594 Ancra Proprietary Nov 17

LIST OF TABLES

TABLE 1-64-00-1 – A SIZE ULD LATERALLY LOADED CG LIMITS ............................................................................................................... 1 TABLE 1-64-00-2 – B SIZE ULD LATERALLY LOADED CG LIMITS ............................................................................................................... 2 TABLE 1-64-00-3 – M SIZE ULD LATERALLY LOADED CG LIMITS .............................................................................................................. 2 TABLE 1-64-00-4 – M SIZE ULD LONGITUDINALLY LOADED CG LIMITS ..................................................................................................... 3 TABLE 1-64-00-5 – K SIZE ULD LONGITUDINALLY LOADED CG LIMITS ...................................................................................................... 3 TABLE 1-64-00-6 – A SIZE ULDS H-ARM ........................................................................................................................................... 6 TABLE 1-64-00-7 – A SIZE ULDS Y-ARM............................................................................................................................................ 6 TABLE 1-64-00-8 – B SIZE ULDS H-ARM ........................................................................................................................................... 7 TABLE 1-64-00-9 – B SIZEULDS Y-ARM ............................................................................................................................................ 7 TABLE 1-64-00-10 – M SIZE ULDS H-ARM ........................................................................................................................................ 8 TABLE 1-64-00-11 – M SIZE ULDS Y-ARM ........................................................................................................................................ 8 TABLE 1-64-00-12 – K SIZE ULDS H-ARM ......................................................................................................................................... 9 TABLE 1-64-00-13 – K SIZE ULDS Y-ARM .......................................................................................................................................... 9 TABLE 1-64-01-14 – MAXIMUM ALLOWABLE WEIGHTS FOR A1 ULD INSTALLED ON 85600-10 CHS ............................................................ 3 TABLE 1-64-01-15 – MAXIMUM ALLOWABLE WEIGHTS FOR A2 ULD INSTALLED ON 85600-10 CHS ............................................................ 4 TABLE 1-64-01-16 – MAXIMUM ALLOWABLE WEIGHTS FOR A3 ULD INSTALLED ON 85600-10 CHS ............................................................ 5 TABLE 1-64-01-17 – MAXIMUM ALLOWABLE WEIGHTS FOR A4 ULD INSTALLED ON 85600-10 CHS ............................................................ 6 TABLE 1-64-01-18 – MAXIMUM ALLOWABLE WEIGHTS FOR A5 ULD INSTALLED ON 85600-10 CHS ............................................................ 7 TABLE 1-64-01-19 – MAXIMUM ALLOWABLE WEIGHTS FOR A6 ULD INSTALLED ON 85600-10 CHS ............................................................ 8 TABLE 1-64-01-20 – MAXIMUM ALLOWABLE WEIGHTS FOR A7 ULD INSTALLED ON 85600-10 CHS ............................................................ 9 TABLE 1-64-01-21 – MAXIMUM ALLOWABLE WEIGHTS FOR A8 ULD INSTALLED ON 85600-10 CHS .......................................................... 10 TABLE 1-64-01-22 – MAXIMUM ALLOWABLE WEIGHTS FOR A9 ULD INSTALLED ON 85600-10 CHS .......................................................... 11 TABLE 1-64-01-23 – MAXIMUM ALLOWABLE WEIGHTS FOR A10 ULD INSTALLED ON 85600-10 CHS ........................................................ 12 TABLE 1-64-01-24 – MAXIMUM ALLOWABLE WEIGHTS FOR A11 ULD INSTALLED ON 85600-10 CHS ........................................................ 13 TABLE 1-64-01-25 – MAXIMUM ALLOWABLE WEIGHTS FOR K12 ULD INSTALLED ON 85600-10 CHS ........................................................ 14 TABLE 1-64-01-26 – 85600-10 CHS COMPONENT AND SYSTEM WEIGHT .................................................................................... 15 TABLE 1-64-02-27 – MAXIMUM ALLOWABLE WEIGHTS FOR A1 ULD INSTALLED ON 85600-17 CHS ............................................................ 3 TABLE 1-64-02-28 – MAXIMUM ALLOWABLE WEIGHTS FOR A2 ULD INSTALLED ON 85600-17 CHS ............................................................ 4 TABLE 1-64-02-29 – MAXIMUM ALLOWABLE WEIGHTS FOR A3 ULD INSTALLED ON 85600-17 CHS ............................................................ 5 TABLE 1-64-02-30 – MAXIMUM ALLOWABLE WEIGHTS FOR A4 ULD INSTALLED ON 85600-17 CHS ............................................................ 6 TABLE 1-64-02-31 – MAXIMUM ALLOWABLE WEIGHTS FOR A5 ULD INSTALLED ON 85600-17 CHS ............................................................ 7 TABLE 1-64-02-32 – MAXIMUM ALLOWABLE WEIGHTS FOR A6 ULD INSTALLED ON 85600-17 CHS ............................................................ 8 TABLE 1-64-02-33 – MAXIMUM ALLOWABLE WEIGHTS FOR A7 ULD INSTALLED ON 85600-17 CHS ............................................................ 9 TABLE 1-64-02-34 – MAXIMUM ALLOWABLE WEIGHTS FOR A8 ULD INSTALLED ON 85600-17 CHS .......................................................... 10 TABLE 1-64-02-35 – MAXIMUM ALLOWABLE WEIGHTS FOR A9 ULD INSTALLED ON 85600-17 CHS .......................................................... 11 TABLE 1-64-02-36 – MAXIMUM ALLOWABLE WEIGHTS FOR A10 ULD INSTALLED ON 85600-17 CHS ........................................................ 12 TABLE 1-64-02-37 – MAXIMUM ALLOWABLE WEIGHTS FOR K12 ULD INSTALLED ON 85600-17 CHS ........................................................ 13 TABLE 1-64-02-38 – MAXIMUM ALLOWABLE WEIGHTS FOR B1 ULD INSTALLED ON 85600-17 CHS .......................................................... 14 TABLE 1-64-02-39 – MAXIMUM ALLOWABLE WEIGHTS FOR B2 ULD INSTALLED ON 85600-17 CHS .......................................................... 15 TABLE 1-64-02-40 – MAXIMUM ALLOWABLE WEIGHTS FOR B3 ULD INSTALLED ON 85600-17 CHS .......................................................... 16 TABLE 1-64-02-41 – MAXIMUM ALLOWABLE WEIGHTS FOR B4 ULD INSTALLED ON 85600-17 CHS .......................................................... 17 TABLE 1-64-02-42 – MAXIMUM ALLOWABLE WEIGHTS FOR B5 ULD INSTALLED ON 85600-17 CHS .......................................................... 18 TABLE 1-64-02-43 – MAXIMUM ALLOWABLE WEIGHTS FOR B6 ULD INSTALLED ON 85600-17 CHS .......................................................... 19 TABLE 1-64-02-44 – MAXIMUM ALLOWABLE WEIGHTS FOR B7 ULD INSTALLED ON 85600-17 CHS .......................................................... 20 TABLE 1-64-02-45 – MAXIMUM ALLOWABLE WEIGHTS FOR B8 ULD INSTALLED ON 85600-17 CHS .......................................................... 21 TABLE 1-64-02-46 – MAXIMUM ALLOWABLE WEIGHTS FOR B9 ULD INSTALLED ON 85600-17 CHS .......................................................... 22 TABLE 1-64-02-47 – MAXIMUM ALLOWABLE WEIGHTS FOR B10 ULD INSTALLED ON 85600-17 CHS ........................................................ 23 TABLE 1-64-02-48 – MAXIMUM ALLOWABLE WEIGHTS FOR B11 ULD INSTALLED ON 85600-17 CHS ........................................................ 24 TABLE 1-64-02-49 – MAXIMUM ALLOWABLE WEIGHTS FOR K12 ULD INSTALLED ON 85600-17 CHS ........................................................ 25

TABLES Page 2/2 10594 Ancra Proprietary Nov 17

TABLE 1-64-02-50 – MAXIMUM ALLOWABLE WEIGHTS FOR M1 ULD INSTALLED ON 85600-17 CHS ......................................................... 26 TABLE 1-64-02-51 – MAXIMUM ALLOWABLE WEIGHTS FOR M2 ULD INSTALLED ON 85600-17 CHS ......................................................... 27 TABLE 1-64-02-52 – MAXIMUM ALLOWABLE WEIGHTS FOR M3 ULD INSTALLED ON 85600-17 CHS ......................................................... 28 TABLE 1-64-02-53 – MAXIMUM ALLOWABLE WEIGHTS FOR M4 ULD INSTALLED ON 85600-17 CHS ......................................................... 29 TABLE 1-64-02-54 – MAXIMUM ALLOWABLE WEIGHTS FOR M5 ULD INSTALLED ON 85600-17 CHS ......................................................... 30 TABLE 1-64-02-55 – MAXIMUM ALLOWABLE WEIGHTS FOR M6 ULD INSTALLED ON 85600-17 CHS ......................................................... 31 TABLE 1-64-02-56 – MAXIMUM ALLOWABLE WEIGHTS FOR M7 ULD INSTALLED ON 85600-17 CHS ......................................................... 32 TABLE 1-64-02-57 – MAXIMUM ALLOWABLE WEIGHTS FOR M8 ULD INSTALLED ON 85600-17 CHS ......................................................... 33 TABLE 1-64-02-58 – MAXIMUM ALLOWABLE WEIGHTS FOR M9 ULD INSTALLED ON 85600-17 CHS ......................................................... 34 TABLE 1-64-02-59 – MAXIMUM ALLOWABLE WEIGHTS FOR M10 ULD INSTALLED ON 85600-17 CHS ....................................................... 35 TABLE 1-64-02-60 – MAXIMUM ALLOWABLE WEIGHTS FOR K12 ULD INSTALLED ON 85600-17 CHS ........................................................ 36 TABLE 1-64-02-61 – MAXIMUM ALLOWABLE WEIGHTS FOR A1 ULD INSTALLED ON 85600-17 CHS .......................................................... 37 TABLE 1-64-02-62 – MAXIMUM ALLOWABLE WEIGHTS FOR A2 ULD INSTALLED ON 85600-17 CHS .......................................................... 38 TABLE 1-64-02-63 – MAXIMUM ALLOWABLE WEIGHTS FOR A3 ULD INSTALLED ON 85600-17 CHS .......................................................... 39 TABLE 1-64-02-64 – MAXIMUM ALLOWABLE WEIGHTS FOR A4 ULD INSTALLED ON 85600-17 CHS .......................................................... 40 TABLE 1-64-02-65 – MAXIMUM ALLOWABLE WEIGHTS FOR M5L ULD INSTALLED ON 85600-17 CHS ....................................................... 41 TABLE 1-64-02-66 – MAXIMUM ALLOWABLE WEIGHTS FOR A7 ULD INSTALLED ON 85600-17 CHS .......................................................... 42 TABLE 1-64-02-67 – MAXIMUM ALLOWABLE WEIGHTS FOR A8 ULD INSTALLED ON 85600-17 CHS .......................................................... 43 TABLE 1-64-02-68 – MAXIMUM ALLOWABLE WEIGHTS FOR A9 ULD INSTALLED ON 85600-17 CHS .......................................................... 44 TABLE 1-64-02-69 – MAXIMUM ALLOWABLE WEIGHTS FOR A10 ULD INSTALLED ON 85600-17 CHS ........................................................ 45 TABLE 1-64-02-70 – MAXIMUM ALLOWABLE WEIGHTS FOR A11 ULD INSTALLED ON 85600-17 CHS ........................................................ 46 TABLE 1-64-02-71 – MAXIMUM ALLOWABLE WEIGHTS FOR K12 ULD INSTALLED ON 85600-17 CHS ........................................................ 47 TABLE 1-64-02-72 – MAXIMUM ALLOWABLE WEIGHTS FOR M1 ULD INSTALLED ON 85600-17 CHS ......................................................... 48 TABLE 1-64-02-73 – MAXIMUM ALLOWABLE WEIGHTS FOR M2 ULD INSTALLED ON 85600-17 CHS ......................................................... 49 TABLE 1-64-02-74 – MAXIMUM ALLOWABLE WEIGHTS FOR M3 ULD INSTALLED ON 85600-17 CHS ......................................................... 50 TABLE 1-64-02-75 – MAXIMUM ALLOWABLE WEIGHTS FOR M4 ULD INSTALLED ON 85600-17 CHS ......................................................... 51 TABLE 1-64-02-76 – MAXIMUM ALLOWABLE WEIGHTS FOR M5L ULD INSTALLED ON 85600-17 CHS ....................................................... 52 TABLE 1-64-02-77 – MAXIMUM ALLOWABLE WEIGHTS FOR M7 ULD INSTALLED ON 85600-17 CHS ......................................................... 53 TABLE 1-64-02-78 – MAXIMUM ALLOWABLE WEIGHTS FOR M8 ULD INSTALLED ON 85600-17 CHS ......................................................... 54 TABLE 1-64-02-79 – MAXIMUM ALLOWABLE WEIGHTS FOR M9 ULD INSTALLED ON 85600-17 CHS ......................................................... 55 TABLE 1-64-02-80 – MAXIMUM ALLOWABLE WEIGHTS FOR M10 ULD INSTALLED ON 85600-17 CHS ....................................................... 56 TABLE 1-64-02-81 – MAXIMUM ALLOWABLE WEIGHTS FOR K12 ULD INSTALLED ON 85600-17 CHS ........................................................ 57 TABLE 1-64-02-82 – 85600-17 CHS COMPONENT AND SYSTEM WEIGHT .................................................................................... 58

1-64-00 Page 1/9 10594 Ancra Proprietary Nov 17

1 CARGO LIMITATION (1-64-00)

This section discusses the general limitations that applies to the cargo.

The 85600-10 & 85600-17 CHS have been designed in accordance to Boeing’s Interface Control

Drawing 851A0001 to be installed on the 737-800BCF main deck cargo compartment.

1.1 UNIT LOAD DEVICE (ULD) LIMITATIONS

The 85600-10 CHS is designed to accommodate the following ULDs:

i. Size A pallets (88”X125”), and

ii. Size K Pallet (60.4”X61.5”)

As for the 85600-17 CHS it can accommodate the following ULDs:

i. Size A pallets (88”X125”),

ii. Size B Pallets (88”X108”) 463L Type,

iii. Size M Pallets (96”X125”), and

iv. Size K Pallet (60.4”X61.5”)

All ULDs used must be certified under NAS 3610 and AS36100.

1.2 ULD CENTER OF GRAVITY (CG) LIMITS

The following subsections will discuss the CG limitations for the ULDs used with the Ancra CHS

85600-10 & 85600-17.

1.2.1 A SIZE ULD LATERALLY LOADED CG LIMITATIONS

Maximum center of gravity height for this type of ULD is 36.0 inches, measured from the bottom of

the ULD. The maximum center of gravity deviations from the ULD geometric center is shown and

defined by the figure and the table below.

Figure 1-64-00-1 – A Size ULD Laterally Loaded CG

Table 1-64-00-1 – A Size ULD Laterally Loaded CG Limits

ALLOWED CENTER OF GRAVITY ±10% LATERAL DIRECTION ±12.5 IN

LONGITUDINAL DIRECTION ±8.8 IN

FWD


1.2.2 B SIZE (463L TYPE) ULD LATERALLY LOADED CG LIMITATIONS




Figure 1-64-00-2 – B Size (463L Type) ULD Laterally Loaded CG

Table 1-64-00-2 – B Size ULD Laterally Loaded CG Limits



1.2.3 M SIZE ULD LATERALLY LOADED CG LIMITATIONS




Figure 1-64-00-3 – M Size ULD Laterally Loaded CG

Table 1-64-00-3 – M Size ULD Laterally Loaded CG Limits



FWD

FWD


1.2.4 M SIZE ULD LONGITUDINALLY LOADED CG LIMITATIONS




Figure 1-64-00-4 – M Size ULD Longitudinally Loaded CG

Table 1-64-00-4 – M Size ULD Longitudinally Loaded CG Limits



1.2.5 K SIZE ULD LONGITUDINALLY LOADED CG LIMITATIONS




Figure 1-64-00-5 – K Size ULD Longitudinally Loaded CG

Table 1-64-00-5 – K Size ULD Longitudinally Loaded CG Limits



FWD

FWD


1.3 MAIN DECK LOADING

The aircraft restraint system must be unimpaired and must be used.

The ULD profile must ensure a sufficient clearance to the cargo door, cargo compartment lining and

the ULD's loaded on the adjacent positions to enable it to be stowed in the aircraft without receiving

or inflicting damage.

Additional requirements have to be considered for loading of the ULD positions directly behind the

rigid cargo barrier.

1.3.1 CONFIGURATIONS 1.3.1.1 (11) 88”X125” ULDS LOADED TRANSVERSELY PLUS (1) 60.4”X61.5” ULD

This configuration is applicable for the 85600-10 & 85600-17 CHS

Figure 1-64-00-6 – (11) 88”X125” ULDS PLUS (1) 60.4”X61.5” ULD

1.3.1.2 (11) 88”X108” 463L ULDS LOADED TRANSVERSELY PLUS (1) 60.4”X61.5” ULD

This configuration is applicable for the 85600-17 CHS.

Figure 1-64-00-7 – (11) 88”x108” 463L ULDs Plus (1) 60.4”x61.5” ULD

1.3.1.3 (10) 96”X125” ULDS LOADED TRANSVERSELY PLUS (1) 60.4”X61.5” ULD


Figure 1-64-00-8 – (10) 96”x125” ULDs Plus (1) 60.4”x61.5” ULD


1.3.1.4 (9) 88”X125” ULDS LOADED TRANSVERSELY PLUS (1) 96”X125” ULD LOADED LONGITUDINALLY PLUS (1) 60.4”X61.5” ULD


Figure 1-64-00-9 – (9) 88”x125” ULDs (1) 96”x125” ULD Longitudinal Plus (1) 60.4”x61.5” ULD

1.3.1.5 (8) 96”X125” ULDS LOADED TRANSVERSELY PLUS (1) 96”X125” ULD LOADED LONGITUDINALLY PLUS (1) 60.4”X61.5” ULD


Figure 1-64-00-10 – (8) 96”x125” ULDs Plus (1) 96”x125” ULD Longitudinal Plus (1) 60.4”x61.5” ULD


1.3.2 GEOMETRY (H-ARM & Y-ARM) 1.3.2.1 A SIZE ULDS

This is applicable for the 85600-10 & 85600-17 CHS

Figure 1-64-00-11 – A Size ULDs Geometry

Table 1-64-00-6 – A Size ULDs H-ARM

ULD TYPE POSITION H-ARM (IN)

FROM TO AVERAGE

88"X125" ULD

A1 356.95 444.95 400.95

A2 445.95 533.95 489.95

A3 534.95 622.95 578.95

A4 623.95 711.95 667.95

A5 712.95 800.95 756.95

A6 801.95 889.95 845.95

A7 890.95 978.95 934.95

A8 979.95 1067.95 1023.95

A9 1068.95 1156.95 1112.95

A10 1157.95 1245.95 1201.95

A11 1246.95 1334.95 1290.95

Table 1-64-00-7 – A Size ULDs Y-ARM

ULD TYPE POSITION Y-ARM (IN)

FROM TO AVERAGE

88"X125" ULD

A1 -62.50 62.50 0.00

A2 -62.50 62.50 0.00

A3 -62.50 62.50 0.00

A4 -62.50 62.50 0.00

A5 -62.50 62.50 0.00

A6 -62.50 62.50 0.00

A7 -62.50 62.50 0.00

A8 -62.50 62.50 0.00

A9 -62.50 62.50 0.00

A10 -62.50 62.50 0.00

A11 -62.50 62.50 0.00


1.3.2.2 B SIZE ULDS

This is applicable for the 85600-17 CHS

Figure 1-64-00-12 – B Size ULDs Geometry

Table 1-64-00-8 – B Size ULDs H-ARM


FROM TO AVERAGE

88"X108" 463L TYPE

ULD

B1 356.95 444.95 400.95

B2 445.95 533.95 489.95

B3 534.95 622.95 578.95

B4 623.95 711.95 667.95

B5 712.95 800.95 756.95

B6 801.95 889.95 845.95

B7 890.95 978.95 934.95

B8 979.95 1067.95 1023.95

B9 1068.95 1156.95 1112.95

B10 1157.95 1245.95 1201.95

B11 1246.95 1334.95 1290.95

Table 1-64-00-9 – B SizeULDs Y-ARM


FROM TO AVERAGE

88"X108” 463L TYPE

ULD

B1 -54.00 54.00 0.00

B2 -54.00 54.00 0.00

B3 -54.00 54.00 0.00

B4 -54.00 54.00 0.00

B5 -54.00 54.00 0.00

B6 -54.00 54.00 0.00

B7 -54.00 54.00 0.00

B8 -54.00 54.00 0.00

B9 -54.00 54.00 0.00

B10 -54.00 54.00 0.00

B11 -54.00 54.00 0.00


1.3.2.3 M SIZE ULDS

This is applicable for the 85600-17 CHS

Figure 1-64-00-13 – A Size ULDs Geometry

Table 1-64-00-10 – M Size ULDs H-ARM


FROM TO AVERAGE

96"X125" ULD

M1 356.95 452.95 404.95

M2 453.95 549.95 501.95

M3 550.95 646.95 598.95

M4 647.95 743.95 695.95

M5 744.95 840.95 792.95

M5L 744.95 869.95 807.45

M6 841.95 937.95 889.95

M7 938.95 1034.95 986.95

M8 1035.95 1131.95 1083.95

M9 1132.95 1228.95 1180.95

M10 1229.95 1325.95 1277.95

Table 1-64-00-11 – M Size ULDs Y-ARM


FROM TO AVERAGE

96"X125" ULD

M1 -62.50 62.50 0.00

M2 -62.50 62.50 0.00

M3 -62.50 62.50 0.00

M4 -62.50 62.50 0.00

M5 -62.50 62.50 0.00

M5L -48.00 48.00 0.00

M6 -62.50 62.50 0.00

M7 -62.50 62.50 0.00

M8 -62.50 62.50 0.00

M9 -62.50 62.50 0.00

M10 -62.50 62.50 0.00


1.3.2.4 K SIZE ULD

This is applicable for the 85600-10 & 85600-17 CHS

Figure 1-64-00-14 – K Size ULDs Geometry

Table 1-64-00-12 – K Size ULDs H-ARM


FROM TO AVERAGE

60.4”X61.5” ULD

K12 1335.95 1397.45 1366.70

Table 1-64-00-13 – K Size ULDs Y-ARM


FROM TO AVERAGE

60.4”X61.5” ULD

K12 -30.20 30.20 0.00



2.1 85600-10 CHS EQUIPMENT MALFUNCTION LIMITATION

This section provides position weight limitation when a single latch or restraint used to secure ULDs

to the floor structure is missing or inoperative. The latches prevent ULD movement during flight which

is critical for flight safety.

A malfunction of any equipment is defined as damaged/inoperative or failed/missing equipment.

If a malfunction of any equipment should occur, onloading and offloading should be carried out

carefully to prevent damage to equipment, ULDs and/or aircraft structure.

All malfunctioning equipment should be replaced as soon as possible.

The tables that follow provide latch and/or restraint identification as well as the ULD load limitation

that must be applied in case of missing or inoperative equipment at that single location.

CAUTION 1: THIS SECTION IS APPLICABLE ONLY TO ANCRA’S 85600-10 CHS.

CAUTION 2: FOR ULD POSITIONS WITH MAXIMUM LOADS, ALL RESTRAINTS

AND LATCHES MUST BE IN PROPER POSITION AND USED AS

INTENDED.

CAUTION 3: ONLY ONE MISSING LATCH OR RESTRAIN IS ALLOWED PER ULD

POSITION.

CAUTION 4: MISSING OR INOPERATIVE GUIDES, CONVEYORS AND ROLLERS

ARE NOT ALLOWED.

CAUTION 5: IN THE FOLLOWING TABLES, WEIGHT REDUCED TO “0” MEANS:

THE APPLICABLE ULD POSITION(S) MUST BE UNOCCUPIED.

LOADING AN EMPTY ULD IN THAT POSITION IS PERMITTED

PROVIDED THERE ARE ENOUGH SERVICABLE LATCHES TO

PREVENT UNCONTROLLED MOVEMENT OF THE ULD.


CAUTION 6: CONFIGURATION - 88 X 125

IN AN EVENT THAT PALLET P7 THROUGH P12 ARE NOT LOADED

TO THEIR MAXIMUM ALLOWED WEIGHT AS SPECIFIED IN THE

APPLICABLE BOEING MANUAL THEN IT SHOULD MEET THE

FOLLOWING LOADING REQUIREMENT:

1. IF A PALLET IS EMPTY I.E; WEIGHT = 0 LBS THEN THE PALLET

ADJACENT TO IT, BOTH IN THE FWD AND AFT DIRECTION

SHOULD BE 0.35 TIMES THE MAXIMUM ALLOWABLE WEIGHT

OF THE PALLET OR LESS

2. BETWEEN ANY TWO ADJACENT PALLETS IF THE AFT

POSITION PALLET IS HEAVIER THAN THE FWD POSITION

PALLET THEN THE DISTRIBUTION OF CARGO SHOULD BE

SUCH THAT THE RATIO OF DISTRIBUTED WEIGHT BETWEEN

THE FWD AND THE AFT PALLET SHOULD BE AT LEAST 0.6 OR

GREATER

3. BETWEEN ANY TWO ADJACENT PALLETS IF THE FWD

POSITION PALLET IS HEAVIER THAN THE AFT POSITION

PALLET THEN THE DISTRIBUTION OF CARGO SHOULD BE

SUCH THAT THE RATIO OF DISTRIBUTED WEIGHT BETWEEN

THE FWD AND THE AFT PALLET SHOULD BE 1.7 OR LESS

Oct 17


2.1.1 ELEVEN (11) 88”X125” ULDS LOADED TRANSVERSELY PLUS ONE (1) 60.4”X61.5” ULD

2.1.1.1 A1 (88”X125”) ULD

Figure 1-64-01-15 – A1 ULD Installed on 85600-10 CHS

Table 1-64-01-14 – Maximum Allowable Weights for A1 ULD Installed on 85600-10 CHS

PALLET ID

ORIGINAL POSITION WEIGHT

MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A1 5300

F1 356.95 -43.08 87024-14 4028

F2 356.95 -22.35 87024-12 3922

F3 356.95 22.35 87024-11 3922

F4 356.95 43.09 87027-13 4081

L1 383.45 -62.50 87010-15 3922

L2 397.45 -62.50 87010-30 4187

L3 416.45 -62.50 87010-29 3498

L4 436.45 -62.50 87010-28 2173

A1 444.95 -45.00 87012-15 3127

A2 444.95 -24.23 87012-13 2438

A3 444.95 0.00 87012-13 3180

A4 444.95 24.13 87012-14 2438

A5 444.95 44.89 87012-14 2438

R1 377.45 62.50 87010-14 3710

R2 396.45 62.50 87010-13 4240

R3 416.45 62.50 87010-12 3498

R4 436.45 62.50 87010-11 2332


2.1.1.2 A2 (88”X125”) ULD



PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A2 5800

F1 445.95 -45.00 87012-15 1914

F2 445.95 -24.23 87012-13 1914

F3 445.95 0.00 87012-13 4466

F4 445.95 24.13 87012-14 3422

F5 445.95 44.89 87012-14 3422

L1 465.45 -62.50 87013-10 3712

L2 482.45 -62.50 87013-11 5800

L3 501.45 -62.50 87013-11 4930

L4 525.45 -62.50 87013-11 2842

A1 533.95 -45.50 87011-10 3364

A2 533.95 -24.75 87011-10 2668

A3 533.95 0.00 87011-10 3480

A4 533.95 24.75 87011-10 2668

A5 533.95 45.50 87011-10 2668

R1 462.45 62.50 87022-11 3596

R2 482.45 62.50 87022-10 5800

R3 502.45 62.50 87022-10 4698

R4 524.45 62.50 87022-10 2900


2.1.1.3 A3 (88”X125”) ULD



PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A3 6500

F1 534.95 -45.50 87011-10 2145

F2 534.95 -24.75 87011-10 2145

F3 534.95 0.00 87011-10 5005

F4 534.95 24.75 87011-10 3770

F5 534.95 45.50 87011-10 3770

L1 543.45 -62.50 87013-11 3250

L2 565.45 -62.50 87013-11 5200

L3 589.95 -62.50 87019-10 5785

L4 606.45 -62.50 87010-10 3900

A1 622.95 -45.50 87011-11 3770

A2 622.95 -24.75 87011-11 2990

A3 622.95 0.00 87011-11 3900

A4 622.95 24.75 87011-11 2990

A5 622.95 45.50 87011-11 2990

R1 543.45 62.50 87022-10 3185

R2 566.45 62.50 87022-10 5265

R3 586.45 62.50 87010-16 5785

R4 606.45 62.50 87010-10 4030


2.1.1.4 A4 (88”X125”) ULD



PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A4 6500

F1 623.95 -45.50 87011-11 2145

F2 623.95 -24.75 87011-11 2145

F3 623.95 0.00 87011-11 5005

F4 623.95 24.75 87011-11 3770

F5 623.95 45.50 87011-11 3770

L1 630.45 -62.50 87010-10 3185

L2 654.45 -62.50 87010-10 5005

L3 675.45 -62.50 87010-10 6175

L4 702.45 -62.50 87010-10 3835

A1 711.95 -45.50 87011-11 3770

A2 711.95 -24.75 87011-11 2990

A3 711.95 0.00 87011-11 3900

A4 711.95 24.75 87011-11 2990

A5 711.95 45.50 87011-11 2990

R1 630.45 62.50 87010-10 3185

R2 654.45 62.50 87010-10 5005

R3 675.45 62.50 87010-10 6175

R4 702.45 62.50 87010-10 3835


2.1.1.5 A5 (88”X125”) ULD



PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A5 10000

F1 712.95 -45.50 87011-11 3300

F2 712.95 -24.75 87011-11 3300

F3 712.95 0.00 87011-11 7700

F4 712.95 24.75 87011-11 5800

F5 712.95 45.50 87011-11 5800

L1 722.35 -62.50 87016-11 4000

L2 734.35 -62.50 87016-11 4500

L3 750.95 -62.50 87018-10 3800

L4 770.95 -62.50 87018-10 7300

L5 792.95 -62.50 87018-10 5000

A1 800.95 -45.50 87011-11 5800

A2 800.95 -24.75 87011-11 4600

A3 800.95 0.00 87011-11 6000

A4 800.95 24.75 87011-11 4600

A5 800.95 45.50 87011-11 4600

R1 722.35 62.50 87016-10 4000

R2 734.35 62.50 87016-10 4500

R3 750.95 62.50 87018-10 3800

R4 770.95 62.50 87018-10 7400

R5 792.95 62.50 87018-10 5000


2.1.1.6 A6 (88”X125”) ULD



PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A6 10000

F1 801.95 -45.50 87011-11 3300

F2 801.95 -24.75 87011-11 3300

F3 801.95 0.00 87011-11 7700

F4 801.95 24.75 87011-11 5800

F5 801.95 45.50 87011-11 5800

L1 807.95 -62.50 87018-10 4400

L2 827.95 -62.50 87018-10 6000

L3 847.95 -62.50 87018-10 4600

L4 861.95 -62.50 87017-10 5700

L5 880.95 -62.50 87017-10 4500

A1 889.95 -45.50 87011-11 5800

A2 889.95 -24.75 87011-11 4600

A3 889.95 0.00 87011-11 6000

A4 889.95 24.75 87011-11 4600

A5 889.95 45.50 87011-11 4600

R1 807.95 62.50 87018-10 4400

R2 827.95 62.50 87018-10 6000

R3 847.95 62.50 87018-10 4600

R4 861.95 62.50 87017-10 5700

R5 880.95 62.50 87017-10 4500


2.1.1.7 A7 (88”X125”) ULD



PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A7 6500

F1 890.95 -45.50 87011-11 2145

F2 890.95 -24.75 87011-11 2145

F3 890.95 0.00 87011-11 5005

F4 890.95 24.75 87011-11 3770

F5 890.95 45.50 87011-11 3770

L1 900.95 -62.50 87018-10 3510

L2 922.95 -62.50 87018-10 5590

L3 947.45 -62.50 87010-10 5460

L4 967.45 -62.50 87010-10 3575

A1 978.95 -45.50 87011-11 3770

A2 978.95 -24.75 87011-11 2990

A3 978.95 0.00 87011-11 3900

A4 978.95 24.75 87011-11 2990

A5 978.95 45.50 87011-11 2990

R1 900.95 62.50 87018-10 3510

R2 922.95 62.50 87018-10 5590

R3 947.45 62.50 87010-10 5460

R4 967.45 62.50 87010-10 3575


2.1.1.8 A8 (88”X125”) ULD



PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A8 6500

F1 979.95 -45.50 87011-11 2145

F2 979.95 -24.75 87011-11 2145

F3 979.95 0.00 87011-11 5005

F4 979.95 24.75 87011-11 3770

F5 979.95 45.50 87011-11 3770

L1 988.45 -62.50 87010-10 2990

L2 1008.45 -62.50 87010-10 4290

L3 1028.45 -62.50 87010-10 6045

L4 1051.45 -62.50 87010-10 4355

A1 1067.95 -45.50 87011-11 3770

A2 1067.95 -24.75 87011-11 2990

A3 1067.95 0.00 87011-11 3900

A4 1067.95 24.75 87011-11 2990

A5 1067.95 45.50 87011-11 2990

R1 988.45 62.50 87010-10 2990

R2 1008.45 62.50 87010-10 4290

R3 1028.45 62.50 87010-10 6045

R4 1051.45 62.50 87010-10 4355


2.1.1.9 A9 (88”X125”) ULD



PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A9 6500

F1 1068.95 -45.50 87011-11 2145

F2 1068.95 -24.75 87011-11 2145

F3 1068.95 0.00 87011-11 5005

F4 1068.95 24.75 87011-11 3770

F5 1068.95 45.50 87011-11 3770

L1 1076.45 -62.50 87010-10 3185

L2 1099.45 -62.50 87010-10 5005

L3 1120.45 -62.50 87010-10 6175

L4 1145.45 -62.50 87010-10 3900

A1 1156.95 -45.50 87011-11 3770

A2 1156.95 -24.75 87011-11 2990

A3 1156.95 0.00 87011-11 3900

A4 1156.95 24.75 87011-11 2990

A5 1156.95 45.50 87011-11 2990

R1 1076.45 62.50 87010-10 3185

R2 1099.45 62.50 87010-10 5005

R3 1120.45 62.50 87010-10 6175

R4 1145.45 62.50 87010-10 3900


2.1.1.10 A10 (88”X125”) ULD



PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A10 5000

F1 1157.95 -45.50 87011-11 1650

F2 1157.95 -24.75 87011-11 1650

F3 1157.95 0.00 87011-11 3850

F4 1157.95 24.75 87011-11 2900

F5 1157.95 45.50 87011-11 2900

L1 1167.45 -62.50 87010-10 2550

L2 1188.45 -62.50 87010-10 3850

L3 1209.45 -62.50 87010-10 4850

L4 1236.45 -62.50 87010-10 2900

A1 1245.95 -45.50 87011-11 2900

A2 1245.95 -24.75 87011-11 2300

A3 1245.95 0.00 87011-11 3000

A4 1245.95 24.75 87011-11 2300

A5 1245.95 45.50 87011-11 2300

R1 1167.45 62.50 87010-10 2550

R2 1188.45 62.50 87010-10 3850

R3 1209.45 62.50 87010-10 4850

R4 1236.45 62.50 87010-10 2900


2.1.1.11 A11 (88”X125”) ULD



PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

A11 5000

F1 1246.95 -45.50 87011-11 1650

F2 1246.95 -24.75 87011-11 1650

F3 1246.95 0.00 87011-11 3850

F4 1246.95 24.75 87011-11 2900

F5 1246.95 45.50 87011-11 2900

L1 1258.45 -62.50 87010-10 2400

L2 1278.45 -62.50 87010-10 3800

L3 1294.45 -62.50 87025-10 4900

L4 1316.35 -62.50 81159-10 3400

A1 1334.95 -45.50 87024-10 2900

A2 1334.95 -24.75 87011-11 2300

A3 1334.95 0.00 87011-11 3000

A4 1334.95 24.75 87011-11 2300

A5 1334.95 45.50 87024-10 2300

R1 1258.45 62.50 87010-10 2400

R2 1278.45 62.50 87010-10 3800

R3 1294.45 62.50 87025-12 4900

R4 1316.35 62.50 81159-11 3400


2.1.1.12 K12 (60.4”X61.5”) ULD

Figure 1-64-01-26 – K12 ULD Installed on 85600-10 CHS

Table 1-64-01-25 – Maximum Allowable Weights for K12 ULD Installed on 85600-10 CHS

PALLET ID


MISSING LOCK ID

MISSING BA

MISSING BL

MISSING PN

ALLOWABLE WEIGHT

K12 3500

F1 1335.95 -24.75 87011-11 2380

F2 1335.95 0.00 87011-11 2380

F3 1335.95 24.75 87011-11 3220

L1 1342.05 -30.20 87014-10 1820

L2 1355.95 -30.20 87014-10 2625

L3 1374.95 -30.20 87014-10 3080

L4 1391.95 -30.20 87014-10 1925

A1 1397.45 -24.75 87015-10 3080

A2 1397.45 0.00 87015-10 2380

A3 1397.45 24.75 87015-10 2380

R1 1342.05 30.20 87014-10 1820

R2 1355.95 30.20 87014-10 2625

R3 1374.95 30.20 87014-10 3080

R4 1391.95 30.20 87014-10 1925


2.2 85600-10 CHS COMPONENT AND SYSTEM WEIGHT

Table 1-64-01-26 – 85600-10 CHS COMPONENT AND SYSTEM WEIGHT

PART NUMBER NOMENCLATURE OR DESCRIBTION QTY UNIT WT. TOTAL WT.

80233-13 BALL MAT ASSEMBLY FILLER PANEL 5 1.90 9.50

84021-33 RAIL ASSY - SIDE GUIDE 2 0.60 1.20













84022-44 RAIL ASSY, SIDE GUIDE INCREASED HEIGHT 3 2.00 6.00





86996-10 ROLLER TRAY ASSY 51 0.80 40.80

86996-11 ROLLER TRAY ASSY 67 1.10 73.70

86996-12 ROLLER TRAY ASSY 19 1.60 30.40

86996-13 ROLLER TRAY ASSY 16 2.10 33.60

86996-15 ROLLER TRAY ASSY 16 0.80 12.80

86996-16 ROLLER TRAY ASSY 8 0.40 3.20

86996-17 ROLLER TRAY ASSY 14 0.70 9.80

86996-18 ROLLER TRAY ASSY 12 0.70 8.40

87001-10 BALL TRAY ASSY 5 2.00 10.00

87001-11 BALL TRAY ASSY 9 2.50 22.50

87001-12 BALL TRAY ASSY 3 1.00 3.00

87010-10 CROSS TRACK ASSEMBLY 42 4.70 197.40










87011-10 CARGO LOCK 1.35 CARGO SYSTEM 5 2.10 10.50

87011-11 CARGO LOCK 1.35 CARGO SYSTEM 43 2.60 111.80

87012-13 CARGO - LOCKWITH LONG BRIDGE 1.35 SYSTEM 1 15.00 15.00



87013-10 CROSS TRACK ASSY DOOR WAY 1 3.10 3.10

87013-11 CROSS TRACK ASSY DOOR WAY 5 3.00 15.00

87014-10 CONVEYOR ASSEMBLY AFT 1 47.00 47.00

87015-10 END STOP ASSY AFT 3 1.20 3.60


Table 1-64-01-26 – 85600-10 CHS COMPONENT AND SYSTEM WEIGHT

PART NUMBER NOMENCLATURE OR DESCRIBTION QTY UNIT WT. TOTAL WT.

87016-10 CONVEYOR ASSEMBLY FWD EXPANSION 1 12.70 12.70

87016-11 CONVEYOR ASSEMBLY FWD EXPANSION 1 12.70 12.70

87017-10 CONVEYOR ASSEMBLY AFT EXPANSION 2 32.30 64.60

87018-10 CROSSTRACK WINGBOX 16 4.80 76.80

87019-10 CROSSTRACK WITH IMPACT DOOR GUIDE ROLLER 1 6.50 6.50

87020-10 BALL MAT ASSY 737-800 CARGO SYSTEM 1 7.30 7.30



















87021-10 DOOR SILL PROTECTOR ASSY 1 25.40 25.40

87021-11 DOOR SILL PROTECTOR ASSY 1 24.40 24.40

87022-10 CROSS TRACK ASSY OPPOSITE OF DOOR WAY 5 3.40 17.00

87022-11 CROSS TRACK ASSY OPPOSITE OF DOOR WAY 1 3.40 3.40

87023-10 CROSS TRACK ASSY WITH GUIDE 2 3.50 7.00

87024-10 FWD STOP 2 1.00 2.00

87024-11 FWD STOP 1 1.00 1.00

87024-12 FWD STOP 1 1.00 1.00

87024-13 FWD STOP 1 1.00 1.00

87024-14 FWD STOP 1 1.00 1.00

87025-10 CROSSTRACK AFT 1 5.90 5.90

87025-12 CROSSTRACK AFT 1 4.10 4.10

87026-10 BALL TRAY ASSY, TRANSVERSE 2 8.60 17.20

87159-10 RAIL ASSEMBLY 1 3.00 3.00

87159-11 RAIL ASSEMBLY 1 3.00 3.00

Total Cargo Handling System Weight, P/N 85600-10: 1544 LB Cargo System Center of Gravity: (X) Balance Arm: 787.14 in (Y) Balance Arm: -1.59 in



3.1 85600-17 CHS EQUIPMENT MALFUNCTION LIMITATION

This section provides position weight limitation when a single latch or restraint used to secure ULDs

to the floor structure is missing or inoperative. The latches prevent ULD movement during flight which

is critical for flight safety.

A malfunction of any equipment is defined as damaged/inoperative or failed/missing equipment.

If a malfunction of any equipment should occur, onloading and offloading should be carried out

carefully to prevent damage to equipment, ULDs and/or aircraft structure.

All malfunctioning equipment should be replaced as soon as possible.

The tables that follow provide latch and/or restraint identification as well as the ULD load limitation

that must be applied in case of missing or inoperative e

title weight and balance manual supplement ...this supplement provides specific weight and balance...

Documents