Three Phase Technical Services

LLC, DubaiLV/MV SWITCHGEAR SITE SERVICESELECTRICAL SYSTEM STUDIESINDUSTRIAL & BUILDING AUTOMATION ENERGY AUDITORS & ELECTRICAL CONSULTANTSBTU METERS

2

OUR OBJECTIVESVISION :- To be a leading service provider for LV/MV Switchgear & Industrial & Building Automation in the Middle East with fair business practices up to Customer satisfaction

MISSION :- We are working with highly motivated

technical crew Putting constant efforts to adapt new

technologiesReview and feedback policy to meet

Customer satisfactionCordial relations with Customers

3

COMPANY SNAPSHOTSName :Three Phase Technical Services LLC

Year Of Inception : 2009

Employees :Designers/Engineers/Skilled Technicians

Field Experience : 17 yrs

Area Of Expertise Design, Installation, Testing, Commissioning, Energy Auditing, Engineering Services & Solutions etc

Contact Us :707, SIT Tower, Dubai Silicon Oasis, Dubai. PO Box: 127023Mob: +971 55 776 6524, Tel: +971 4 396 4086, Fax: +971 4 396 4087E-mail: info@3phtechservices.com or azmat.baig@3phtechservices.com

4

OUR MARKET – BUILDING SEGMENT

5

OUR MARKET – INFRASTRUCTURE SEGMENT

6

OUR MARKET – INDUSTRIAL SEGMENT

7

OUR MARKET – UTILITIES SEGMENT

8

OUR MARKET – OIL & GAS SEGMENT

9

OUR SERVICES HIGHLIGHTS

10

Electrical - Refurbishment & Retrofitting

Disconnection / Removal of switchgear then re-connect it after refurbishment

We can provide site audits of switchgear and protection system

Extensive expertise of upgrading protection systems by installing new relays for change of use or modernization/upgrade of protection and control systems.

 Onsite services ranging from circuit breaker repairs & installation.

Removal and re-installation of LV switchboardsPerforming full commissioning tests.Complete overhaul and replacement of LV

busbarsRemoval, installation and commissioning of LV

and MV components in power sub-stations. Design and installation of key interlocking

systems.

11

Benefits of facility refurbishmentImproves electrical equipment

reliability.

Extends the equipment life cycle.

Improvement in your quality of

service for the client.

Shows your commitment to quality to

your client. Reduction in downtime & operating

cost.

More economical than complete

replacement.

Incorporation of the latest

technology.

12

Annual Maintenance Contract (AMC)To prove the integrity of entire Electrical & Building

Automation System.

Identification of discrepancies, design concerns, control

system logic, construction or operational defects.

AMC/O&M services include Project Management,

Supervision and Engineering, Technicians (Electrical /

Automation), Project Data Entry and Document

Management, Punch List, Certification and Handover.

Pre-Commissioning, Commissioning, operations, Training

and System Integration

13

Thermography ( Thermal Imaging)It’s a process of using special cameras designed to look

only for heat by the way of infrared energy waves. Most valuable diagnostic tools for predictive maintenance

of electrical installationsIt detect anomalies often invisible to the naked eye,

thereby allowing corrective action to be taken.Diagnostics of electrical equipments, mainly transformers

insulators & switchgears. Fast and non-exhausting measurements of devices that

are not easily accessible or where measurements are dangerous to humans.

We provide full support in the rectification of any problems that are found by thermal imaging

14

Harmonic Measurement (Analysis)Harmonics in power systems can result in undesirable

influence such as Capacitor heating or failure, Telephone interference, Rotating equipment heating, Protection Relay malfunctioning, Transformer heating, Switchgear failure, Fuse blowing etc.

The main sources of harmonics in power system are static power converters (Electronic equipments which converts sinusoidal to non-sinusoidal), arc furnaces, discharge lighting and any other load that requires non-sinusoidal current.

In order to limit the harmonic current propagation in to the network, harmonic filters are placed close to the source of the harmonic currents.

Harmonic filters provide low impedance paths to harmonic currents and thus prevent them from flowing into the power network.

Harmonic Measurements & Analysis computes indices such as total voltage harmonic distortion factor at buses to evaluate the effect of the harmonic sources and to calculate the sizing of filters.

 

15

Capacitor Banks (Analysis)Adding power factor correction capacitors provides

well-known benefits to industrial plants, include power factor correction, voltage support, and release of system capacity.

However application of capacitors in power systems with excessive harmonics and/or transients might not survive long if they are improperly applied.

Capacitors are also known to cause power quality problems, such as oscillatory switching transients, and can possibly amplify other problems, such as harmonics.

Capacitors that solves some problems can cause other problems.

Variable Frequency Drives (VFDs) are another such example.

We investigates capacitor failures and fuse operations in an automatically switched capacitor bank.

Either harmonics are the sources of problem.

Or else transients from an unlikely source were to blame.

 

16

Energy Auditing (Energy Management)An energy audit is the first step to

determine how much energy your facility consumes

Evaluate the steps to be taken to make the property more energy efficient.

An energy audit provides you with the framework needed to establish or improve energy management.

It also provides a baseline for saving money and energy over time when corrected.

The audit of energy consumption is a specialized process.

It takes thorough knowledge and expertise in multiple fields to estimate design, commission and performance monitor projects for energy conservation.

17

Training We provides you with professional training opportunities to enhance

skills and knowledge of LV Switchgear & Industrial Automation solutions.

Whether in the training centre at our office, or on-site at your premises.

We listen to your specific requirements and organize the most relevant training courses.

Our courses are aimed at technicians, supervisors & engineers whose job function requires competencies to supervise, select, install, commission, maintain and test electrical -instrumentation systems and equipment.

We design tailor-made training packages for professionals who are committed to learn and gain experience in instruments and systems installed in the Industrial process and general maintenance services.

We give your teams the necessary skills to work better and ensure the security of your operations, while at the same time optimizing the efficiency of installed equipment.

18

for your attention

T hanks