the next steps for ultra-high temperature ceramics
TRANSCRIPT
![Page 1: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/1.jpg)
Engineering Conferences InternationalECI Digital ArchivesUltra-High Temperature Ceramics: Materials ForExtreme Environmental Applications II Proceedings
Spring 5-14-2014
The Next Steps for Ultra-High TemperatureCeramicsEric WuchinaNaval Surface Warfare Center
M. OpekaNaval Surface Warfare Center
Follow this and additional works at: http://dc.engconfintl.org/uhtc
Part of the Materials Science and Engineering Commons
This Conference Proceeding is brought to you for free and open access by the Proceedings at ECI Digital Archives. It has been accepted for inclusion inUltra-High Temperature Ceramics: Materials For Extreme Environmental Applications II by an authorized administrator of ECI Digital Archives. Formore information, please contact [email protected].
Recommended CitationEric Wuchina and M. Opeka, "The Next Steps for Ultra-High Temperature Ceramics" in "Ultra-High Temperature Ceramics: MaterialsFor Extreme Environmental Applications II", W. Fahrenholtz, Missouri Univ. of Science & Technology; W. Lee, Imperial CollegeLondon; E.J. Wuchina, Naval Service Warfare Center; Y. Zhou, Aerospace Research Institute Eds, ECI Symposium Series, (2013).http://dc.engconfintl.org/uhtc/3
![Page 2: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/2.jpg)
E. Wuchina
The Next Steps for UHTC Materials
M. Opeka
NSWCCD, Bethesda, MD/ONR, Arlington, VA
Ultra-High Temperature Ceramics for Extreme Environment Applications II
May 14, 2012
Hernstein, Austria
![Page 3: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/3.jpg)
Outline
BackgroundWhy UHTCs?
Current research & development focus
Systems Needs/Designers Phobias – are UHTCs getting a bad reputation?getting a bad reputation?
How to integrate into structure?Catastrophic FailureLong-term applications - oxidation
What needs to be done?New Processing TechnologiesTesting in Relevant Environments
![Page 4: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/4.jpg)
Why UHTCs?
What does a UHTC need to do:- Carry engineering load at RT - √- Carry load at high use temperature- Respond to thermally generated stresses (coatings)- Survive thermochemical environment - √
High Melting Temperature is a major criteria, but not the only oneMelting temperature of oxide phases formedMelting temperature of oxide phases formedPotential eutectic formation
Thermal Stress – R’ = σσσσk/(ααααE)Increasing strength helps, but only to certain extent
Applications are not just function of temperature- Materials needs for long flight time reusable vehicles are different that those for expendable weapons systems
![Page 5: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/5.jpg)
Random Thoughts
In many aerospace systems, designers will add weight and complexity by
using metals and active fuel cooling to avoid using advanced ceramics and
composites. - Direct function of the conservatism engrained in industry and the
system integrator being contracted to build a system and not
demonstrate a materials technology- Unfamiliarity with designing with brittle materials - safety factor.
- Advantages of weight savings and uncooled temperature capability not high enough to overcome risk aversionnot high enough to overcome risk aversion
Using monolithic ceramics and CMC requires a different design approach, not
just dropping in a ceramic part to replace a metallic component
- Rocket nozzle examples – learning how to use a brittle material in a highly transient heating environment
Need for subscale materials/component testing in realistic environments is imperative
Onus is on US to develop materials that will be used by designers
![Page 6: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/6.jpg)
High Temp Materials SelectionThermochemistry is Driver
- Metallurgical Thermo tools employed
- Lines divide stability regions of metal vs condensed metal oxide0
4
(a
tm) W-WO
3
Re-Re2O
7
Ir-IrO2
2000 40002500 3000
T (°C)
3500
Os-OsO4
Oxide Stable
- Each element shown is best representative of Group (eg., Ta-Nb-V)
- Each element is also representative of compounds (HfC, HfN, HfB2, HfO2, etc.)
- So what ???? How is this useful ????
2.503.003.504.004.505.00
104/T (K-1)
-16
-12
-8
-4
log
Po
2 (
atm
)
Y-Y2O
3
Be-BeO
Hf-HfO2
Ta-Ta2O
5
3
O Metal MPQ Oxide MP& M-C MP, MC MP
Si-SiO2
Al-Al2O
3 Metal Stable
![Page 7: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/7.jpg)
Current research vs
future directions
• Increase strength - SPS (engineers don’t like lack of toughness)
• Increase thermal conductivity (HfB2 is already very high)
• Decrease modulus (graphite second phases, but eutectic issue)
• Decrease thermal expansion (intrinsic property)
• Design around thermal stresses – rocket nozzles (ONR & AFRL)
• Understand and improve oxidation behavior – why SiC?• Understand and improve oxidation behavior – why SiC?
• Develop UHTC-matrix composites – hot pressing, SPS, HIP, all produce bulk monolithic materials.
– Modulus/CTE mismatch w/ C fibers a problem
– Current polymeric precursors - expensive and air sensitive
– Organnometallics
– Melt infiltration – refractory alloys reactive with fibers
– Densification/conversion of matrix
– Alternative Processing routes (CVC, in-situ reinforcement, cermets)
![Page 8: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/8.jpg)
High Operational Velocities ⇒⇒⇒⇒ High Temps & Heating Rates
NAI : One Mach Number per Year to 201225
Production
Hydrogen ScramjetMach 8-15
0 2 4 6 8 10
Mach Number
0
500
1000
1500
2000
2500
3000
3500
4000
Sta
gnation T
em
p (
ºC)
0
1000
2000
3000
4000
5000
6000
7000
Sta
gnation T
em
p (
ºF)High
Velocity = High Temps
Hypersonics
1960 1970 1980 1990 2000 2010 20200
5Ma
ch
Nu
mb
er
10
15
F-4
SR-71
F-15F-16 F-22
Hydrocarbon Scramjet Mach 4-7
Production
NAI
RamjetMach 3-4
High Speed TurbineMach 2-4
X-15
Concorde
XB-70
B-2F-117
Mach 8-15
Weapons
Strike Aircraft
SpaceAccess
X-Vehicles
&
![Page 9: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/9.jpg)
Higher Operating Temps Yield Higher Engine Performance
BreakthroughMaterials
TechnologyExample: Gas Turbine Engine
All Propulsion (Turbines, Rockets) Subject to 2nd Law
Thermodynamics
Data from Dr. B. L. Koff, Pratt& Whitney, 1996
Loss If No Matls Devt
![Page 10: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/10.jpg)
0
500
1000
1500
2000
2500
3000
3500
4000
Sta
gnation T
em
p (
ºC)
0
1000
2000
3000
4000
5000
6000
7000
Sta
gnation T
em
p (
ºF)
Scramjet PropulsionHigh Operational Velocities → High Temps & Heat Rates
High speed = High T
0 2 4 6 8 10
Mach Number
0 0
![Page 11: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/11.jpg)
Pressure-Time Traces of Graphite &
HfB2 Throats Showing Non-eroding
Behavior of Ceramic Nozzle
![Page 12: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/12.jpg)
Thermal Stress-Based Failure Mode:
Thinner Liners - Lower Thermally Generated Stresses
![Page 13: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/13.jpg)
THERMALLY GENERATED STRESSES
Solid HfB2 Throat
Similar Axial Stress Fields Have Been Observed
In Previous Analysis Efforts
Maybe the models are too conservative in
predicting thermal stress failures?
![Page 14: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/14.jpg)
Understanding of Oxidation at
Relevant Temperatures
SiO2
ZrO2 (B) + SiO2
Ref: Evaluation of Ultra High Temperature Ceramics for Propulsion ApplicationS.R. Levine, et al., NASA Glenn Res. Ctr, ACerS PacRim Conf., Seattle, WA, 01 Nov 2002
(1627C not high enough!)
SiO fills
ZrB2
holes
SiC
100 µm
Major: Monoclinic Trace: Cubic
SiO2 fills pores in HfO2
![Page 15: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/15.jpg)
Borides are not the
only UHTC Materials
Boria has high Pv, SiC active oxidation, and HfO2
does not sinter below 1800°C, so oxidation
behavior improves with temperature
![Page 16: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/16.jpg)
Arc-jet tests help understanding
thermochemical environment
HfN.75HfN.95
But sample geometry (radius of curvature), enthalpy, catalycity, and pressure all affect performance
![Page 17: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/17.jpg)
Relevant Testing Can be
Enlightening – and Scary
♦ SHARP-B2 UHTC flight test [Sannes, 9 and Johnson, 10]
• Very progressive & expensive
• Failure attributed to UHTC
processing
Pre-test Post-testSlide from D. Glass, NASA-Langley
♦ ZrB2-SiC nose tip during arc-jet test [Marino, 11].
• Failure attributed to titanium screw [12].
Second assembly withstood two test at 3 MW/m2 for 108 sec. Non-critical damage observed at base of UHTC tip. [Scatteia, 12]
Affecting future of Italian UHTC work?
Even in constrained 1-D heating environment for oxidation testing, low thermal shock resistance and low fracture toughness of
monolithic ceramics can result in catastrophic failure
Photos of
UHTC nose tip
during failure
![Page 18: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/18.jpg)
Improve oxidation
behavior
• Eliminate presence of Si - detrimental above 1700°C
• Test in relevant environments
• Dopants to control oxygen diffusion through oxide scale
• Decrease porosity of scale
- Substoichiometry & Doping – Wuchina & Opeka
- Liquid phase sintering – Fahrenholtz & HilmasWO3
HfCxOy Interphase
WO3
formation
Careful on effects on high-temperature strength
![Page 19: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/19.jpg)
Current NSWCCD Research Oxidation and Mechanical Properties in
the Hf-Ta-N System
Hf, Ta: Linear Oxidation Kinetics at High Temperature (HT)
Hf-20Ta: Parabolic Kinetics to 2000°C with strongly adherent scale (Marnoch, 1965)
HfC, HfC-25TaC
Hf20Ta:
HfO2 columnar
morphology in
alloy & oxide
(600X)
Oxidized 2100°C, 10 min
HfC-25TaC: Linear Kinetics at HT (Holcomb, 1988)
HfB2-20TaB2: Linear Kinetics at HT (Talmy, unpublished)
(Hf,Ta)Nx Ceramics: Not Investigated To-Date; Initial Navy Expts Conducted with HfTa alloys
Oxidized at 2000°C
(600X)
(10X)
Hf27Ta:
Oxidized at 1500C,
15 minutes; Oxide
scale thickness ≈
50 µm
![Page 20: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/20.jpg)
Alternative Processing
Techniques
CVD not a panacea, but shows possibilities
![Page 21: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/21.jpg)
UHTC-matrix composite – ca
1997 and Hf-HfN-HfB2 cermet
Hf acetate + C, CVI, C/C late stage PIP or gas infiltration, nano HfC
X-51 Inlet leading edge was follow-on
to work initiated in
late 1990s through SBIR
![Page 22: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/22.jpg)
Chemical Vapor Composites CVD with Particulate or fiber
reinforcement
![Page 23: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/23.jpg)
The Intersection of Basic
Science and Engineering
Ab-initio calculations for discovery of new materials and correlation of
chemical & physical models with materials by design approach for improving properties
High-fidelity analysis to understand multi-scale effects on macroscopic properties
Chemical Vapor InfiltrationOrgannometallic PrecursorsOrgannometallic PrecursorsMean Free Path
Modulus Mismatch – fiber breakage
PIP ProcessingPreceramic Polymer Development
Particulate Additions – filtration
Increase Yield & Reduce Cycles
Other TechniquesVapor Phase ConversionUHTC fibers
![Page 24: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/24.jpg)
New Materials for Hypersonic
Vehicles Include Eutectics
Hard-Hard Ceramic Eutectic Hard-Soft Ceramic Eutectic
ZrB2
SiC C
E
E
P
2270°C 2390°C
Hypersonics Aerosurfaces:
ZrB2-SiC (-C)
HfB2-SiC (-C)
SiC ZrB2 ZrB2 C
Microstructure and Property Differences Between Hard-Hard and Hard-Soft Ceramic Eutectics?
ZrB2
![Page 25: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/25.jpg)
New Materials for Propulsion
Systems Include Eutectics
Microstructure and Properties of Ceramic-Metal Eutectics?
Eutectic Temps & Intersolubilities Vary Significantly: HfC-W: 2890°C, HfN-W: 2800°C (PN2-Dependent), HfB2-W: 2280°C
HfC-Ta: 2550°C (large intersolubilities) HfN-Ta: 2800°C (some intersolubility) HfB2-Ta: Reaction to (TaHf)B
Non-Aluminized Propulsion:
HfC-W HfN-W
HfC-Ta HfN-Ta
(and ZrC, ZrN compositions)
HfB2-Ta: Reaction to (TaHf)B
Composition Control and Properties of “Metal” Phase a Major Issue for Cermet Eutectics
![Page 26: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/26.jpg)
New Materials for Propulsion
Systems Include Eutectics
Aluminized Boost Propulsion:
TaC-C
Non-Aluminized Non-Aluminized Boost Propulsion:
HfC-C HfN-BN HfB2-BN
![Page 27: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/27.jpg)
From CAD to part using laser or e-beam(?) metal deposition:
Metals were low-hanging fruit – Refractory Eutectic Ceramics and/or Coatings
are a bit tougher
Deposition Nozzle
Notional Eutectic Production via Additive Manufacturing
Pre-Alloyed
Titanium Powder
CO2 Laser
Substrate/Target Material
(could be casting, forging or rolled plate)
Laser Deposited Material
X
Y
Z
![Page 28: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/28.jpg)
Structural Insulators: A
Materials Challenge
High Strength High Temperature High Thermal Resistance (H,H,H)
High Strength Low Temperature High Thermal Resistivity (H,L,H)
Low Strength High Temperature High Thermal Resistivity (L,H,H)
Thermal Resistivity
• Maximize three competingproperties simultaneously
- Mechanical properties
(strength, fracture toughness)
- High use temperature
(@ high heating rates)
- High Thermal Resistivity
(H,H,H)(L,H,H)
Strength
Temperature
High Strength High Temperature Low Thermal Resistivity (H,H,L)
![Page 29: The Next Steps for Ultra-High Temperature Ceramics](https://reader031.vdocuments.site/reader031/viewer/2022022123/6212e50f75281269f848b08a/html5/thumbnails/29.jpg)
Conclusions
UHTCs are necessary for future hypersonic flight/propulsion systems due to higher use temperatures
Oxidation must be understood and controlled
Monolithic Ceramics will not likely be used in flight Monolithic Ceramics will not likely be used in flight hardware
Flaw Sensitivity (Attachment issues)
Thermal Shock failure
Current work – joining and reinforced UHTCs
Do good research, but think like an engineer, not a scientist!